ADSLF-MIB
81 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.4.32.1 | ScalaradslLineCoding | read-only | mandatory | Specifies the ADSL coding type used on this line. Other types may be added in the future with higher values ala ifIANAtype. This is used to create a LCS sub-MI… |
| 1.3.6.1.4.1.429.4.32.2 | ScalaradslLineType | read-only | mandatory | this describes which other tables go with this ifEntry. use EITHER three separate ifEntries (and adslLinEntries): (1) and tables 1,2,3, 6,7,8,9 (2) with 1,4,5,… |
| 1.3.6.1.4.1.429.4.32.3 | ScalaradslLineSpecific | read-only | mandatory | OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATU-C interface in a DSLAM (among other possibilities) |
| 1.3.6.1.4.1.429.4.32.4 | ScalaradslLineStatus | read-only | mandatory | Status indicates mandatory state of the line. This is a bit-map of possible conditions. These are from the perspective of the ATU-C, since any loss of communic… |
| 1.3.6.1.4.1.429.4.32.5 | ScalaradslAturInvSerialNumber | read-only | mandatory | Vendor specific Serial number of the ATU-C modem |
| 1.3.6.1.4.1.429.4.32.6 | ScalaradslAturInvVendorID | read-only | mandatory | The vendor ID assigned by T1E1.4 according to its Appendix D. |
| 1.3.6.1.4.1.429.4.32.7 | ScalaradslAturCurrOutputPower | read-only | mandatory | Current output power |
| 1.3.6.1.4.1.429.4.32.8 | ScalaradslAturCurrTransmitRate | read-only | mandatory | Current transmit rate in kbps, limited to multiples of 32kbps |
| 1.3.6.1.4.1.429.4.32.9 | ScalaradslAturCurrCodeWordLength | read-only | mandatory | Current Code Word Length, calculated from Transmit rate and noise margin |
| 1.3.6.1.4.1.429.4.32.10 | ScalaradslAturCurrSnrMgn | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.11 | ScalaradslAturCurrAtn | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.12 | ScalaradslAturCurrReceiveGain | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.13 | ScalaradslAturPerfValidIntervals | read-only | mandatory | number of valid intervals in the adslAturPerfDataTable |
| 1.3.6.1.4.1.429.4.32.14 | ScalaradslAturPerfLof | read-only | mandatory | count of the number of Loss of Framing events since system reset. |
| 1.3.6.1.4.1.429.4.32.15 | ScalaradslAturPerfLos | read-only | mandatory | count of the number of Loss of Signal events since system reset. |
| 1.3.6.1.4.1.429.4.32.16 | ScalaradslAturPerfLpr | read-only | mandatory | count of the number of Loss of Power events since system reset. |
| 1.3.6.1.4.1.429.4.32.17 | ScalaradslAturPerfCV | read-only | mandatory | count of the number of Loss of Coding Violation events since system reset. |
| 1.3.6.1.4.1.429.4.32.18 | ScalaradslAturPerfES | read-only | mandatory | count of the number of Errored Seconds since system reset. |
| 1.3.6.1.4.1.429.4.32.19 | ScalaradslAturPerfCurr1DayElapSecs | read-only | mandatory | The total time interval over which all Curr1Day interval counters are measured. If 0, this interval is invalid. |
| 1.3.6.1.4.1.429.4.32.20 | ScalaradslAturPerfCurr1DayMoniSecs | read-only | mandatory | The total number of valid seconds in the Curr1Day interval counters. This may be less than adslAturPerfCurr1DayElapSecs only when there were some seconds in th… |
| 1.3.6.1.4.1.429.4.32.21 | ScalaradslAturPerfPrev1DayElapSecs | read-only | mandatory | The total time interval over which all Prev1Day interval counters are measured. If 0, this interval is invalid. |
| 1.3.6.1.4.1.429.4.32.22 | ScalaradslAturPerfPrev1DayMoniSecs | read-only | mandatory | The total number of valid seconds in the Prev1Day interval counters. This may be less than adslAturPerfPrev1DayElapSecs only when there were some seconds in th… |
| 1.3.6.1.4.1.429.4.32.23 | ScalaradslAturPerfCurr1DayLofs | read-only | mandatory | Count of the number of seconds when there was Loss of Framing during the mandatory day, as measured by adslAturPerfCurr1DayElapSecs. |
| 1.3.6.1.4.1.429.4.32.24 | ScalaradslAturPerfPrev1DayLofs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.25 | ScalaradslAturPerfCurr1DayLoss | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.26 | ScalaradslAturPerfPrev1DayLoss | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.27 | ScalaradslAturPerfCurr1DayLprs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.28 | ScalaradslAturPerfPrev1DayLprs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.29 | ScalaradslAturPerfCurr1DayCVs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.30 | ScalaradslAturPerfPrev1DayCVs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.31 | ScalaradslAturPerfCurr1DayES | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.32 | ScalaradslAturPerfPrev1DayES | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.33 | ScalaradslAturPerfCurr15minLofs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.34 | ScalaradslAturPerfPrev15minLofs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.35 | ScalaradslAturPerfCurr15minLoss | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.36 | ScalaradslAturPerfPrev15minLoss | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.37 | ScalaradslAturPerfCurr15minLprs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.38 | ScalaradslAturPerfPrev15minLprs | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.39 | ScalaradslAturPerfCurr15minES | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.40 | ScalaradslAturPerfPrev15minES | read-only | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.41 | ScalaradslAturThresh15MinLofs | read-write | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.42 | ScalaradslAturThresh15MinLoss | read-write | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.43 | ScalaradslAturThresh15MinLprs | read-write | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.44 | ScalaradslAturThresh15MinCVs | read-write | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.45 | ScalaradslAturThresh15MinES | read-write | mandatory | to be supplied. |
| 1.3.6.1.4.1.429.4.32.46 | ScalaradslAturInitFailureTrapEnable | read-write | mandatory | values as above |
| 1.3.6.1.4.1.429.4.32.47 | ScalaradslAturChanCurrTxRate | read-only | mandatory | derived from adslAturConfMinTxRate + <available excess bandwidth> * (adslAturConfRateChanRatio / 100) as long as it is < adslAturChanConfMaxTxRate |
| 1.3.6.1.4.1.429.4.32.48 | ScalaradslAturChanPrevTxRate | read-only | mandatory | The rate that was set at the previous adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Small rate changes are accum… |
| 1.3.6.1.4.1.429.4.32.49 | ScalaradslAturChanReceivedBlocks | read-only | mandatory | count of all encoded blocks received on this channel. |
| 1.3.6.1.4.1.429.4.32.50 | ScalaradslAturChanTransmittedBlocks | read-only | mandatory | count of all encoded blocks transmitted on this channel. |
| 1.3.6.1.4.1.429.4.32.51 | ScalaradslAturChanCorrectedBlocks | read-only | mandatory | count of all blocks received with errors that were corrected. These blocks are passed on as good data. |
| 1.3.6.1.4.1.429.4.32.52 | ScalaradslAturChanUncorrectableBlocks | read-only | mandatory | count of all blocks received with uncorrectable errors. These blocks are dropped from the received data stream. |
| 1.3.6.1.4.1.429.4.32.53 | ScalarusrAdslCFMStatusFlag | read-write | mandatory | This variable controls saving and loading of configuration information for the ADSL WAN Driver. The value can be set to either save or load by a management sta… |
| 1.3.6.1.4.1.429.4.32.54 | ScalarusrAdslCfgFileName | read-only | mandatory | The name of a ConfigFile to read/write the ADSL parameters. If the value of this object is an empty string, then the ADSL Driver uses the default name `@file:/… |
| 1.3.6.1.4.1.429.4.32.55 | ScalarusrAdslResetStatus | read-write | mandatory | The Reset Status of the ADSL Starlet chipset |
| 1.3.6.1.4.1.429.4.32.56 | ScalarusrAdslActualBaudDataRateDwn | read-only | mandatory | Actual Downstream Baud Rate |
| 1.3.6.1.4.1.429.4.32.57 | ScalarusrAdslFwRel | read-only | mandatory | Firmware release number of the GTI supplied transceiver software module. |
| 1.3.6.1.4.1.429.4.32.58 | ScalarusrAdslAdiVerson | read-only | mandatory | Value is a number that corresponds to the version number of the ADI chipset. |
| 1.3.6.1.4.1.429.4.32.59 | ScalarusrAdslLocalReqDwnConstStatus | read-write | mandatory | Value corresponds to the local downstream constellation requested. |
| 1.3.6.1.4.1.429.4.32.60 | ScalarusrAdslActualUpConstStatus | read-only | mandatory | Value corresponds to the actual upstream constellation that was used, which may differ from the value requested. |
| 1.3.6.1.4.1.429.4.32.62 | ScalarusrAdslRemoteReqUpConstStatus | read-only | mandatory | Value corresponds to the remote requested downstream constellation requested. |
| 1.3.6.1.4.1.429.4.32.63 | ScalarusrAdslStartletVerson | read-only | mandatory | Value is a number that corresponds to the version number of the STARLET VLSI in the transceiver. |
| 1.3.6.1.4.1.429.4.32.64 | ScalarusrAdslActualDwnConstStatus | read-only | mandatory | Value corresponds to the actual downstream constellation that was used, which may differ from the value requested. |
| 1.3.6.1.4.1.429.4.32.65 | ScalarusrAdslLocalReqUpConstStatus | read-write | mandatory | Value corresponds to the local upstream constellation requested. |
| 1.3.6.1.4.1.429.4.32.66 | ScalarusrAdslRemoteReqDwnConstStatus | read-only | mandatory | Value corresponds to the remote downstream constellation requested. |
| 1.3.6.1.4.1.429.4.32.67 | ScalarusrAdslLocalReqBaudDataRateDwn | read-write | mandatory | Local Downstream Baud Rate requested by the User. |
| 1.3.6.1.4.1.429.4.32.68 | ScalarusrAdslFixBitStatus | read-write | mandatory | Fixed Bit Rate feature status. |
| 1.3.6.1.4.1.429.4.32.69 | ScalarusrAdslLocalReqXmitPower | read-write | mandatory | Transmit power requested at the local ADSL transceiver represented i n dB. |
| 1.3.6.1.4.1.429.4.32.70 | ScalarusrAdslRemoteProtocolType | read-only | mandatory | Protocol type in use by the remote RTU. |
| 1.3.6.1.4.1.429.4.32.71 | ScalarusrAdslMeanSqError | read-only | mandatory | Received signal to noise ratio. |
| 1.3.6.1.4.1.429.4.32.72 | ScalarusrAdslLocalActualXmitPower | read-only | mandatory | Transmit power of the local ADSL transceiver represented in dB. |
| 1.3.6.1.4.1.429.4.32.73 | ScalarusrAdslOverFlowCounter | read-only | mandatory | Running counter for when usrAdslBytesErrorCorrected or usrAdslBytesNotErrorCorrected overflows. This Number is reset to zero each time the Transceiver transiti… |
| 1.3.6.1.4.1.429.4.32.74 | ScalarusrAdslLastFailedStatus | read-only | mandatory | Defines the last detailed state reached in usrAdslStartupProgress before startup failed. |
| 1.3.6.1.4.1.429.4.32.75 | ScalarusrAdslBytesNotErrCorrected | read-only | mandatory | Number of bytes not corrected by Reed-Solomon error correction algorithm in the STARLET.This Number is reset to zero each time the Transceiver transitions from… |
| 1.3.6.1.4.1.429.4.32.76 | ScalarusrAdslOpState | read-only | mandatory | Defines the high level operating state of the transceiver. Used by the customer to determine whether the transceiver is in idle mode or data mode. |
| 1.3.6.1.4.1.429.4.32.77 | ScalarusrAdslBytesErrCorrected | read-only | mandatory | Number of bytes corrected by Reed-Solomon error correction algorithm in the STARLET.This Number is reset to zero each time the Transceiver transitions from Idl… |
| 1.3.6.1.4.1.429.4.32.78 | ScalarusrAdslLocalProtocolType | read-only | mandatory | Protocol type in use by the local RTU. |
| 1.3.6.1.4.1.429.4.32.79 | ScalarusrAdslLastFailedErrorValue | read-only | mandatory | Defines the last detailed value reached in usrAdslStartupProgress before startup failed. |
| 1.3.6.1.4.1.429.4.32.81 | ScalarusrAdslLocalReceiverGain | read-only | mandatory | Total local receiver gain measured in dB. |
| 1.3.6.1.4.1.429.4.32.82 | ScalarusrAdslSwitchType | read-write | mandatory | DSLAM switch type. |
| 1.3.6.1.4.1.429.4.32.90 | ScalarusrAdslRemoteReqBaudDataRateDwn | read-only | mandatory | Remote Downstream Baud Rate requested by the User. |