ADTRAN-ATLAS-T1-MIB
72 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.664 | Nodeadtran | |||
| 1.3.6.1.4.1.664.2 | NodeadMgmt | |||
| 1.3.6.1.4.1.664.2.154 | NodeadATLASmg | |||
| 1.3.6.1.4.1.664.2.154.1 | NodeadGenATLASmg | |||
| 1.3.6.1.4.1.664.2.154.1.9 | NodeadATLAST1mg | |||
| 1.3.6.1.4.1.664.2.154.1.9.1 | ScalaradATLAST1IfNumber | read-only | mandatory | The number of T1 ports (regardless of their current state) present on this system. |
| 1.3.6.1.4.1.664.2.154.1.9.2 | TableadATLAST1IfTable | not-accessible | mandatory | The Atlas T1 Interface Status Table |
| 1.3.6.1.4.1.664.2.154.1.9.2.1 | RowadATLAST1IfEntry | not-accessible | mandatory | An entry in the Atlas T1 Interface Status Table |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.1 | ColumnadATLAST1IfIndex | read-only | mandatory | This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-I… |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.2 | ColumnadATLAST1IfSlotNum | read-only | mandatory | This variable indicates the slot number of a particular ATLAS module with a T1 interface. |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.3 | ColumnadATLAST1IfPortNum | read-only | mandatory | This variable indicates the port number of a particular T1 interface on an ATLAS module. |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.4 | ColumnadATLAST1IfAlarmStatus | read-only | mandatory | This variable shows the status of each alarm by setting a bit. If the bit is set the alarm is active. Multiple bits can be set at one time. Bit # ALARM 0x01 LO… |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.5 | ColumnadATLAST1IfRxLevel | read-only | mandatory | This variable represents the recieved signal strength in dB. |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.6 | ColumnadATLAST1IfCurrentLOFC | read-only | mandatory | This variable indicates the value of the loss of frame count for the current 15 minute interval. |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.7 | ColumnadATLAST1IfTotalLOFC | read-only | mandatory | This variable indicates the value of the loss of frame count for the current 24 hours. |
| 1.3.6.1.4.1.664.2.154.1.9.2.1.8 | ColumnadATLAST1IfResetPRMStats | read-write | mandatory | This variable resets the performance monitoring statistics for all of the intervals: current, 15 min, and total. |
| 1.3.6.1.4.1.664.2.154.1.9.3 | TableadATLAST1IfIntervalTable | not-accessible | mandatory | The Atlas T1 Interface Interval Performance Table |
| 1.3.6.1.4.1.664.2.154.1.9.3.1 | RowadATLAST1IfIntervalEntry | not-accessible | mandatory | An entry in the Atlas T1 Interface Interval Performance Table |
| 1.3.6.1.4.1.664.2.154.1.9.3.1.1 | ColumnadATLAST1IfIntervalIndex | read-only | mandatory | This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-I… |
| 1.3.6.1.4.1.664.2.154.1.9.3.1.2 | ColumnadATLAST1IfIntervalNumber | read-only | mandatory | A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming tha… |
| 1.3.6.1.4.1.664.2.154.1.9.3.1.3 | ColumnadATLAST1IfIntervalLOFC | read-only | mandatory | The Loss of Frame Count encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.664.2.154.1.9.4 | TableadATLAST1IfDS0Table | not-accessible | mandatory | The Atlas T1 Interface DS0 Table |
| 1.3.6.1.4.1.664.2.154.1.9.4.1 | RowadATLAST1IfDS0Entry | not-accessible | mandatory | An entry in the Atlas T1 Interface DS0 Table |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.1 | ColumnadATLAST1IfDS0Index | read-only | mandatory | This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-I… |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.2 | ColumnadATLAST1IfDS0Status | read-only | mandatory | This variable shows the overall status of each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different status stat… |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.3 | ColumnadATLAST1IfDS0Alarm | read-only | mandatory | This variable shows the overall alarm status of each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different alarm… |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.4 | ColumnadATLAST1IfDS0RxSignalStatusA | read-only | mandatory | This variable shows the status of the receive signal's A bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the… |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.5 | ColumnadATLAST1IfDS0RxSignalStatusB | read-only | mandatory | This variable shows the status of the receive signal's B bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the… |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.6 | ColumnadATLAST1IfDS0TxSignalStatusA | read-only | mandatory | This variable shows the status of the transmit signal's A bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for th… |
| 1.3.6.1.4.1.664.2.154.1.9.4.1.7 | ColumnadATLAST1IfDS0TxSignalStatusB | read-only | mandatory | This variable shows the status of the transmit signal's B bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for th… |
| 1.3.6.1.4.1.664.2.154.1.9.5 | TableadATLAST1TstTable | not-accessible | mandatory | The Atlas T1 Test Table |
| 1.3.6.1.4.1.664.2.154.1.9.5.1 | RowadATLAST1TstEntry | not-accessible | mandatory | An entry in the Atlas T1 Test Table |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.1 | ColumnadATLAST1TstIndex | read-only | mandatory | This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-I… |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.2 | ColumnadATLAST1TstLocalLpBk | read-write | mandatory | This variable sets the status of the local loopback for sending test signals. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.3 | ColumnadATLAST1TstRemoteLpBk | read-write | mandatory | This variable sets the status of the remote loopback for sending test signals. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.4 | ColumnadATLAST1TstRemoteLpBkStatus | read-only | mandatory | This variable indicates the current remote loopback status. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.5 | ColumnadATLAST1TstPattern | read-write | mandatory | This variable sets the pattern to be sent for testing. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.6 | ColumnadATLAST1TstPatternSync | read-only | mandatory | This variable shows whether there is sync between transmitting and recieving the test pattern. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.7 | ColumnadATLAST1TstPatternSyncLost | read-only | mandatory | This variable shows whether sync has been lost since it was last cleared. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.8 | ColumnadATLAST1TstPatternESs | read-only | mandatory | This variable shows the amount of errored seconds since it was last cleared. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.9 | ColumnadATLAST1TstPatternBESs | read-only | mandatory | This variable shows the amount of bursty errored seconds since it was last cleared. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.10 | ColumnadATLAST1TstPatternSESs | read-only | mandatory | This variable shows the amount of severely errored seconds since it was last cleared. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.11 | ColumnadATLAST1TstClearResults | read-write | mandatory | This variable is used to clear the results of the test. |
| 1.3.6.1.4.1.664.2.154.1.9.5.1.12 | ColumnadATLAST1TstInjectError | read-write | mandatory | This variable is used to inject an error in the test pattern. |
| 1.3.6.1.4.1.664.2.154.15400900 | NodeadATLAST1RxYellowActive | This trap indicates a yellow alarm is being received. | ||
| 1.3.6.1.4.1.664.2.154.15400901 | NodeadATLAST1RxYellowInActive | This trap indicates a yellow alarm is no longer being received. | ||
| 1.3.6.1.4.1.664.2.154.15400902 | NodeadATLAST1RxAISActive | This trap indicates an alarm indication signal (AIS) is being received. | ||
| 1.3.6.1.4.1.664.2.154.15400903 | NodeadATLAST1RxAISInActive | This trap indicates an alarm indication signal (AIS) is no longer being received. | ||
| 1.3.6.1.4.1.664.2.154.15400904 | NodeadATLAST1RedAlarmActive | This trap indicates a red alarm is active. | ||
| 1.3.6.1.4.1.664.2.154.15400905 | NodeadATLAST1RedAlarmInActive | This trap indicates a red alarm is inactive. | ||
| 1.3.6.1.4.1.664.2.154.15400906 | NodeadATLAST1LOSActive | This trap indicates a loss of signal (LOS) is active. | ||
| 1.3.6.1.4.1.664.2.154.15400907 | NodeadATLAST1LOSInActive | This trap indicates a loss of signal (LOS) is inactive. | ||
| 1.3.6.1.4.1.664.2.154.15400908 | NodeadATLAST1TxAISActive | This trap indicates an alarm indication signal (LOS) is being sent. | ||
| 1.3.6.1.4.1.664.2.154.15400909 | NodeadATLAST1TxAISInActive | This trap indicates an alarm indication signal (LOS) is no longer being sent. | ||
| 1.3.6.1.4.1.664.2.154.15400910 | NodeadATLAST1TxYellowActive | This trap indicates a yellow alarm is being sent. | ||
| 1.3.6.1.4.1.664.2.154.15400911 | NodeadATLAST1TxYellowInActive | This trap indicates a yellow alarm is no longer being sent. | ||
| 1.3.6.1.4.1.664.2.154.15400912 | NodeadATLAST1CurrentES | This trap indicates that the current interval errored second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400913 | NodeadATLAST1CurrentSES | This trap indicates that the current interval severely errored second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400914 | NodeadATLAST1CurrentSEFS | This trap indicates that the current interval severely errored framing second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400915 | NodeadATLAST1CurrentUAS | This trap indicates that the current interval unavailable second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400916 | NodeadATLAST1CurrentCSS | This trap indicates that the current interval controlled slip second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400917 | NodeadATLAST1CurrentPCV | This trap indicates that the current interval path coding violations threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400918 | NodeadATLAST1CurrentLES | This trap indicates that the current interval line errored second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400919 | NodeadATLAST1CurrentLCV | This trap indicates that the current interval line code violations threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400920 | NodeadATLAST1TotalES | This trap indicates that the total errored second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400921 | NodeadATLAST1TotalSES | This trap indicates that the total severely errored second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400922 | NodeadATLAST1TotalSEFS | This trap indicates that the total severely errored framing second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400923 | NodeadATLAST1TotalUAS | This trap indicates that the total unavailable second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400924 | NodeadATLAST1TotalCSS | This trap indicates that the total controlled slip second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400925 | NodeadATLAST1TotalPCV | This trap indicates that the total path coding violations threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400926 | NodeadATLAST1TotalLES | This trap indicates that the total line errored second threshold has been exceeded. | ||
| 1.3.6.1.4.1.664.2.154.15400927 | NodeadATLAST1TotalLCV | This trap indicates that the total line code violations threshold has been exceeded. |