ADTRAN-DSUIQ-MIB
188 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.664.1.141 | NodeadDSUIQ | |||
| 1.3.6.1.4.1.664.1.141.14101 | NodeadDSUIQNetworkPhysUp | This trap indicates that the physical layer of the network is now up. | ||
| 1.3.6.1.4.1.664.1.141.14102 | NodeadDSUIQNetworkPhysDown | This trap indicates that the physical layer of the network is now down. | ||
| 1.3.6.1.4.1.664.1.141.14103 | NodeadDSUIQNetworkLMIUp | This trap indicates that the LMI state of the network is now up. | ||
| 1.3.6.1.4.1.664.1.141.14104 | NodeadDSUIQNetworkLMIDown | This trap indicates that the LMI state of the network is now down. | ||
| 1.3.6.1.4.1.664.1.141.14105 | NodeadDSUIQColdStart | This trap indicates that a cold start has occurred. | ||
| 1.3.6.1.4.1.664.2.141 | NodeadDSUIQmg | |||
| 1.3.6.1.4.1.664.2.141.1 | NodeadDSUIQSystemConfig | |||
| 1.3.6.1.4.1.664.2.141.1.1 | ScalaradDSUIQPassword | read-write | mandatory | Sets the Telnet and Vt100 Terminal Control Password (10 characters maximum). |
| 1.3.6.1.4.1.664.2.141.1.2 | ScalaradDSUIQTOD | read-write | mandatory | Sets the Time of Day with the format hh:mm. |
| 1.3.6.1.4.1.664.2.141.1.3 | ScalaradDSUIQDate | read-write | mandatory | Sets the Date with format MM-DD-YY. |
| 1.3.6.1.4.1.664.2.141.1.4 | ScalaradDSUIQIpAddress | read-write | mandatory | Sets the unit's IP Address. |
| 1.3.6.1.4.1.664.2.141.1.5 | ScalaradDSUIQIpAddressMask | read-write | mandatory | Sets the unit's Subnet Mask. |
| 1.3.6.1.4.1.664.2.141.1.6 | ScalaradDSUIQGatewayIpAddress | read-write | mandatory | Sets the Network's Gateway IP Address. |
| 1.3.6.1.4.1.664.2.141.1.7 | ScalaradDSUIQTrapManagerIpAddress | read-write | mandatory | Sets the IP Address of the Trap Host Manager. |
| 1.3.6.1.4.1.664.2.141.1.8 | ScalaradDSUIQTrapManagerDLCI | read-write | mandatory | Sets the DLCI of the Trap Host Manager. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.1.9 | ScalaradDSUIQTrapManagerPort | read-write | mandatory | Selects the Trap Manager Port. |
| 1.3.6.1.4.1.664.2.141.1.10 | ScalaradDSUIQControPortBaud | read-write | mandatory | Selects the Control Port baud rate. |
| 1.3.6.1.4.1.664.2.141.1.11 | ScalaradDSUIQControPortMode | read-write | mandatory | Selects the Control Port protocol. |
| 1.3.6.1.4.1.664.2.141.1.12 | ScalaradDSUIQEnableTraps | read-write | mandatory | Overall trap enable/disable. |
| 1.3.6.1.4.1.664.2.141.1.13 | ScalaradDSUIQAlarmState | read-only | mandatory | This bit map variable indicates alarm conditions which are currently set. When an alarm condition occurs, the corresponding event bit is set in this variable. … |
| 1.3.6.1.4.1.664.2.141.1.14 | ScalaradDSUIQArmAlarm | read-write | mandatory | This bit map variable arms or disarms an individual or group of events identified in adFradAlarmState as a source for generation of an Alarm Trap. The various … |
| 1.3.6.1.4.1.664.2.141.1.15 | ScalaradDSUIQAbortConfig | read-write | mandatory | A Set will cancel the current selections and revert to the last Saved configuration. |
| 1.3.6.1.4.1.664.2.141.1.16 | ScalaradDSUIQSaveConfig | read-write | mandatory | A Set operation will reset the unit and save current selections. |
| 1.3.6.1.4.1.664.2.141.2 | NodeadDSUIQNetPortConfig | |||
| 1.3.6.1.4.1.664.2.141.2.1 | ScalaradDSUIQNetPortLoopRate | read-write | mandatory | Selects the Rate for the DDS interface. |
| 1.3.6.1.4.1.664.2.141.2.2 | ScalaradDSUIQNetPortClockSource | read-write | mandatory | Selects the Timing source for the DDS interface. |
| 1.3.6.1.4.1.664.2.141.2.3 | ScalaradDSUIQNetPortSignaling | read-write | mandatory | Signaling type for the frame relay management interface. |
| 1.3.6.1.4.1.664.2.141.2.4 | ScalaradDSUIQNetPortt391 | read-write | mandatory | Sets the polling interval in seconds for the frame relay management interface. (Range 5 - 30). |
| 1.3.6.1.4.1.664.2.141.2.5 | ScalaradDSUIQNetPortn391 | read-write | mandatory | Sets the interval between full status polls for the frame relay management interface. (Range 1 - 255). |
| 1.3.6.1.4.1.664.2.141.2.6 | ScalaradDSUIQNetPortn392 | read-write | mandatory | Sets the error count for the frame relay management interface. (Range 1 - 10). |
| 1.3.6.1.4.1.664.2.141.2.7 | ScalaradDSUIQNetPortn393 | read-write | mandatory | Sets the error window (number of polling events)for the frame relay management interface. (Range 1 - 10). |
| 1.3.6.1.4.1.664.2.141.2.8 | ScalaradDSUIQNetPortMgmtDlci1Mode | read-write | mandatory | Sets the mode for the managent DLCI 1. If set for shared, management DLCI 1 is used for customer data and IQ management data. If set for dedicated, management … |
| 1.3.6.1.4.1.664.2.141.2.9 | ScalaradDSUIQNetPortMgmtDlci2Mode | read-write | mandatory | Sets the mode for the managent DLCI 2. If set for shared, management DLCI 2 is used for customer data and IQ management data. If set for dedicated, management … |
| 1.3.6.1.4.1.664.2.141.2.10 | ScalaradDSUIQNetMgmtDlci1 | read-write | mandatory | Sets the DLCI for management PVC 1. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.2.11 | ScalaradDSUIQNetMgmtDlci2 | read-write | mandatory | Sets the DLCI for management PVC 2. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.2.12 | ScalaradDSUIQNetPortMaxPVCs | read-write | mandatory | Sets the maxium PVCs supported by the IQ unit. (Range 1 - 100). |
| 1.3.6.1.4.1.664.2.141.2.13 | ScalaradDSUIQNetPortHistIntervals | read-write | mandatory | Sets the number of history intervals for storage. |
| 1.3.6.1.4.1.664.2.141.2.14 | ScalaradDSUIQNetPortHistIntervalsAvailable | read-only | mandatory | Returns the number of history intervals allowed based on the maxium number of PVCs selected. |
| 1.3.6.1.4.1.664.2.141.3 | NodeadDSUIQDtePortConfig | |||
| 1.3.6.1.4.1.664.2.141.3.1 | ScalaradDSUIQDtePortInterface | read-write | mandatory | Selects the DTE Port Interface type. |
| 1.3.6.1.4.1.664.2.141.3.2 | ScalaradDSUIQDtePortRate | read-write | mandatory | Selects the DTE Port Rate. |
| 1.3.6.1.4.1.664.2.141.3.3 | ScalaradDSUIQDteCTSOption | read-write | mandatory | Selects the Clear to Send (CTS) option. |
| 1.3.6.1.4.1.664.2.141.3.4 | ScalaradDSUIQDteCDOption | read-write | mandatory | Selects the Carrier Detect (CD) option. |
| 1.3.6.1.4.1.664.2.141.3.5 | ScalaradDSUIQDteDSROption | read-write | mandatory | Selects the Data Set Ready (DSR) option. |
| 1.3.6.1.4.1.664.2.141.3.6 | ScalaradDSUIQDtePortMgmtDLCI | read-write | mandatory | Sets the DTE Port Management DLCI. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.3.7 | ScalaradDSUIQDtePortt392 | read-write | mandatory | Sets the timeout in seconds between polling intervals. (Range 5 - 30). |
| 1.3.6.1.4.1.664.2.141.3.8 | ScalaradDSUIQDtePortn392 | read-write | mandatory | Sets the number of error events for the frame relay management. (Range 1 - 10). |
| 1.3.6.1.4.1.664.2.141.3.9 | ScalaradDSUIQDtePortn393 | read-write | mandatory | Sets the error window (polling events) for the frame relay management (Range 1 - 10). |
| 1.3.6.1.4.1.664.2.141.3.10 | ScalaradDSUIQDteManagementPvcOption | read-write | mandatory | Controls the presence of the DTE management PVC in a full status response to the DTE device. |
| 1.3.6.1.4.1.664.2.141.3.11 | ScalaradDSUIQDteSignalingResponsesOption | read-write | mandatory | Determines how the IQ device will respond to polls from the DTE device during a network failure. If set to always on, the IQ will respond to polls during a net… |
| 1.3.6.1.4.1.664.2.141.3.12 | ScalaradDSUIQDteFlowControlOption | read-write | mandatory | Determines how the IQ device will respond to congestion during DBU operation. If set for none, the IQ will drop frames during DBU operation when severe congest… |
| 1.3.6.1.4.1.664.2.141.4 | NodeadDSUIQPvcConfig | |||
| 1.3.6.1.4.1.664.2.141.4.1 | TableadDSUIQPvcConfigTable | not-accessible | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.4.1.1 | RowadDSUIQPvcConfigEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.4.1.1.1 | ColumnadDSUIQPvcConfigIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.4.1.1.2 | ColumnadDSUIQPvcDLCI | read-write | mandatory | Address for this PVC entry. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.4.1.1.3 | ColumnadDSUIQPvcCIR | read-write | mandatory | Commited Information Rate for this PVC in Kbps. |
| 1.3.6.1.4.1.664.2.141.4.1.1.4 | ColumnadDSUIQPvcSequenceOption | read-write | mandatory | Sequence number allows the IQ to detect lost frames across the frame relay service. This option should be disabled for PVCs that do not have IQ on both ends. |
| 1.3.6.1.4.1.664.2.141.4.1.1.5 | ColumnadDSUIQPvcDelayPacketOption | read-write | mandatory | Delay packet option for this PVC allows the IQ to sample round trip delay across the frame relay service. This option should be disabled for PVCs that do not h… |
| 1.3.6.1.4.1.664.2.141.4.1.1.6 | ColumnadDSUIQPvcDBUDLCI | read-write | mandatory | Used when this PVC entry is used for dial backup. This value should contain the PVC address as seen on the far end of the PVC. |
| 1.3.6.1.4.1.664.2.141.4.1.1.7 | ColumnadDSUIQPvcStatsControl | read-write | mandatory | Stats Control option determines how the IQ will track statistics for this PVC entry. Auto will allow the IQ to track statistics for a PVC if enough memory is a… |
| 1.3.6.1.4.1.664.2.141.5 | NodeadDSUIQCurrentStatus | |||
| 1.3.6.1.4.1.664.2.141.5.1 | ScalaradDSUIQDDSState | read-only | mandatory | Current status of the DDS interface |
| 1.3.6.1.4.1.664.2.141.5.2 | ScalaradDSUIQDteControlLeads | read-only | mandatory | This bit map integer reflects the current state of the DTE control leads as follows: bit meaning 0 CTS 1 RTS 2 DSR 3 DTR 4 DCD A 1 means the lead is on. |
| 1.3.6.1.4.1.664.2.141.5.3 | ScalaradDSUIQDBUPortType | read-only | mandatory | Returns the DBU card type installed. |
| 1.3.6.1.4.1.664.2.141.5.4 | ScalaradDSUIQLANPortStatus | read-only | mandatory | Returns the LAN card type installed. |
| 1.3.6.1.4.1.664.2.141.5.5 | ScalaradDSUIQLEDstatus | read-only | mandatory | This bit map integer reflects DSUIQ front panel LED state as follows: bit meaning 0 TEST 1 ALARM 2 DCD 3 RD 4 TD 5 CTS 6 RTS |
| 1.3.6.1.4.1.664.2.141.5.6 | ScalaradDSUIQDTESignalingState | read-only | mandatory | Current state of the PVC signaling between the DSUIQ and the attached frame relay dte. |
| 1.3.6.1.4.1.664.2.141.5.7 | ScalaradDSUIQNETSignalingState | read-only | mandatory | Current state of the PVC signaling between the DSUIQ and the frame relay service. |
| 1.3.6.1.4.1.664.2.141.5.8 | ScalaradDSUIQNETPVCCount | read-only | mandatory | Current count of network pvcs. |
| 1.3.6.1.4.1.664.2.141.5.9 | ScalaradDSUIQNETPVCConfigTableSize | read-only | mandatory | Current count of rows in the PVC config table. |
| 1.3.6.1.4.1.664.2.141.5.10 | ScalaradDSUIQDBUState | read-only | mandatory | Current state of the DBU interface. |
| 1.3.6.1.4.1.664.2.141.6 | NodeadDSUIQIntDDSStatus | |||
| 1.3.6.1.4.1.664.2.141.6.1 | TableadDSUIQIntDDSStatusTable | not-accessible | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.6.1.1 | RowadDSUIQIntDDSStatusEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.6.1.1.1 | ColumnadDSUIQIntDDSSlotIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.6.1.1.2 | ColumnadDSUIQIntDDSUnavailableTime | read-only | mandatory | Amount of time in seconds the DDS port is unavailable due to test or in an inactive state. |
| 1.3.6.1.4.1.664.2.141.6.1.1.3 | ColumnadDSUIQIntDDSStateChange | read-only | mandatory | Number of changes in the DDS port state. This includes all normal, inactive, and test state transitions. |
| 1.3.6.1.4.1.664.2.141.6.1.1.4 | ColumnadDSUIQIntDDSBPVFrameError | read-only | mandatory | Number of BPVs received when the DDS is set for 56K mode or the number of DDS framing errors when the DDS is set for 64K mode. |
| 1.3.6.1.4.1.664.2.141.7 | NodeadDSUIQDayDDSStatus | |||
| 1.3.6.1.4.1.664.2.141.7.1 | TableadDSUIQDayDDSStatusTable | not-accessible | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.7.1.1 | RowadDSUIQDayDDSStatusEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.7.1.1.1 | ColumnadDSUIQDayDDSSlotIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.7.1.1.2 | ColumnadDSUIQDayDDSUnavailableTime | read-only | mandatory | Amount of time in seconds the DDS port is unavailable due to test or in an inactive state. |
| 1.3.6.1.4.1.664.2.141.7.1.1.3 | ColumnadDSUIQDayDDSStateChange | read-only | mandatory | Number of changes in the DDS port state. This includes all normal, inactive, and test state transitions. |
| 1.3.6.1.4.1.664.2.141.7.1.1.4 | ColumnadDSUIQDayDDSBPVFrameError | read-only | mandatory | Number of BPVs received when the DDS is set for 56K mode or the number of DDS framing errors when the DDS is set for 64K mode. |
| 1.3.6.1.4.1.664.2.141.8 | NodeadDSUIQDiagnostic | |||
| 1.3.6.1.4.1.664.2.141.8.1 | TableadDSUIQDiagnosticTable | not-accessible | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.8.1.1 | RowadDSUIQDiagnosticEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.8.1.1.1 | ColumnadDSUIQDiagnosticIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.8.1.1.2 | ColumnadDSUIQDiagnosticDlci | read-only | mandatory | Sets the DLCI for PVC Loopback. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.8.1.1.3 | ColumnadDSUIQDiagnosticControl | read-write | mandatory | Starts or Stops PVC Loopback Test. |
| 1.3.6.1.4.1.664.2.141.8.1.1.4 | ColumnadDSUIQDiagnosticDuration | read-write | mandatory | Sets the Length of the PVC Loopback in minutes. |
| 1.3.6.1.4.1.664.2.141.8.1.1.5 | ColumnadDSUIQDiagnosticStatus | read-write | mandatory | PVC Loopback Test Status. (Active/Inactive). |
| 1.3.6.1.4.1.664.2.141.8.1.1.6 | ColumnadDSUIQDiagnosticSecondsRemaining | read-only | mandatory | PVC Loopback Test time remaining in seconds. |
| 1.3.6.1.4.1.664.2.141.8.1.1.7 | ColumnadDSUIQDiagnosticFramesTx | read-only | mandatory | Diagnostic Frames transmitted. |
| 1.3.6.1.4.1.664.2.141.8.1.1.8 | ColumnadDSUIQDiagnosticFramesRx | read-only | mandatory | Diagnostic Frames received. |
| 1.3.6.1.4.1.664.2.141.8.1.1.9 | ColumnadDSUIQDiagnosticLostFrames | read-only | mandatory | Diagnostic Frames Lost. |
| 1.3.6.1.4.1.664.2.141.8.1.1.10 | ColumnadDSUIQDiagnosticMaxDelay | read-only | mandatory | Diagnostic Maximum Delay measurement. |
| 1.3.6.1.4.1.664.2.141.8.1.1.11 | ColumnadDSUIQDiagnosticMinDelay | read-only | mandatory | Diagnostic Minimum Delay measurement. |
| 1.3.6.1.4.1.664.2.141.8.1.1.12 | ColumnadDSUIQDiagnosticAvgDelay | read-only | mandatory | Diagnostic Average Delay measurement. |
| 1.3.6.1.4.1.664.2.141.9 | NodeadDSUIQDBUConfig | |||
| 1.3.6.1.4.1.664.2.141.9.1 | ScalaradDSUIQDBUOption | read-write | mandatory | This option specifies whether the unit automatically enters dial backup mode or waits for manual setup. |
| 1.3.6.1.4.1.664.2.141.9.2 | ScalaradDSUIQDBUStartLockout | read-write | mandatory | This option selects the hour to begin disabling dial backup operation when daily or weekend lockout mode is active. |
| 1.3.6.1.4.1.664.2.141.9.3 | ScalaradDSUIQDBUEndLockout | read-write | mandatory | This option selects the hour to end dial backup lockout when daily or weekend lockout mode is active. |
| 1.3.6.1.4.1.664.2.141.9.4 | ScalaradDSUIQDBUMode | read-write | mandatory | This option specifies the dial backup operating mode for the unit as orginate or answer. One end must be set to originate and the other end to answer. |
| 1.3.6.1.4.1.664.2.141.9.5 | ScalaradDSUIQDBUOOS | read-write | mandatory | This option enables the unit to enter backup mode if an out-of-service condition is detected from the network. |
| 1.3.6.1.4.1.664.2.141.9.6 | ScalaradDSUIQDBUNoRx | read-write | mandatory | This option enables the unit to enter backup mode when a loss of receive signal is detected from the network. |
| 1.3.6.1.4.1.664.2.141.9.7 | ScalaradDSUIQDBUNoSealCurr | read-write | mandatory | This option enables the unit to enter backup mode when a loss of sealing current is detected from the network. |
| 1.3.6.1.4.1.664.2.141.9.8 | ScalaradDSUIQDBUNoLMI | read-write | mandatory | This option enables the unit to enter backup mode when network PVC signaling state goes down. |
| 1.3.6.1.4.1.664.2.141.9.9 | ScalaradDSUIQAutoRestoreTimer | read-write | mandatory | This option selects the amount of time that the DSUIQ circuit must be active before the unit switches from backup to normal mode of operation. The timer value … |
| 1.3.6.1.4.1.664.2.141.9.10 | ScalaradDSUIQRedialCount | read-write | mandatory | This option allows the selection of the number of times the unit will redial the Far End unit when attempting to go to backup and a busy or reorder condition o… |
| 1.3.6.1.4.1.664.2.141.9.11 | ScalaradDSUIQDBUFailTimeout | read-write | mandatory | This option allows the selection of the amount of time that the dedicated circuit failure condition is active before attempting to enter dial backup mode. The … |
| 1.3.6.1.4.1.664.2.141.9.12 | ScalaradDSUIQDBURedialTimer | read-write | mandatory | This option works in conjunction with the Redial Counter option. The Redial Timer specifies the amount of time between redial attempts. The Redial Timer value … |
| 1.3.6.1.4.1.664.2.141.9.13 | ScalaradDSUIQDBUPassCheck | read-write | mandatory | This option allows the unit to send and verify a dial backup passcode for an additional level of security. When enabled, the originate unit sends the passcode … |
| 1.3.6.1.4.1.664.2.141.9.14 | ScalaradDSUIQDBUPassCode | read-write | mandatory | This option sets the dial backup passcode used to provide an additional level of security. A passcode of one to ten digit characters can be set. If enabled, th… |
| 1.3.6.1.4.1.664.2.141.9.15 | ScalaradDSUIQWeekendLockout | read-write | mandatory | This option enables or disables Weekend Lockout for Dial Backup operation. If enabled, no backup will occur from midnight Friday to midnight Sunday. |
| 1.3.6.1.4.1.664.2.141.9.16 | ScalaradDSUIQDailyLockout | read-write | mandatory | This option enables or disables Daily Lockout for Dial Backup operation. If enabled, no backup will occur between Lockout Start hour and Lockout End hour. |
| 1.3.6.1.4.1.664.2.141.9.17 | ScalaradDSUIQAnswerAlways | read-write | mandatory | This option enables or disables Answer Always for Dial Backup operation. If enabled, the answer unit answers any incoming call regardless of failed conditions. |
| 1.3.6.1.4.1.664.2.141.9.18 | ScalaradDSUIQBeeperOption | read-write | mandatory | This option enables or disables the audible alarm when the IQ unit goes into dial backup mode. |
| 1.3.6.1.4.1.664.2.141.9.19 | ScalaradDSUIQDBUPhoneNumber1 | read-write | mandatory | This option is used to set a phone number to place a DBU call. |
| 1.3.6.1.4.1.664.2.141.9.20 | ScalaradDSUIQDBUPhoneNumber2 | read-write | mandatory | This option is used to set a phone number to place a DBU call. |
| 1.3.6.1.4.1.664.2.141.9.21 | ScalaradDSUIQDBUPhoneNumber3 | read-write | mandatory | This option is used to set a phone number to place a DBU call. |
| 1.3.6.1.4.1.664.2.141.9.22 | ScalaradDSUIQDBUPhoneNumber4 | read-write | mandatory | This option is used to set a phone number to place a DBU call. |
| 1.3.6.1.4.1.664.2.141.9.23 | ScalaradDSUIQDBUPhoneNumber5 | read-write | mandatory | This option is used to set a phone number to place a DBU call. |
| 1.3.6.1.4.1.664.2.141.9.24 | ScalaradDSUIQDBUISDNSwitch | read-write | mandatory | This option is used to select the ISDN switch type. |
| 1.3.6.1.4.1.664.2.141.9.25 | ScalaradDSUIQDBUISDNBChannelRate | read-write | mandatory | This option is used to select the ISDN channel rate. |
| 1.3.6.1.4.1.664.2.141.9.26 | ScalaradDSUIQDBUISDNSPID | read-write | mandatory | This option is used to set the SPID for the ISDN interface. |
| 1.3.6.1.4.1.664.2.141.9.27 | ScalaradDSUIQDBUISDNLDN | read-write | mandatory | This option is used to set LDN for the ISDN interface. |
| 1.3.6.1.4.1.664.2.141.9.28 | ScalaradDSUIQV34LineType | read-write | mandatory | This option selects the type of analog phone line. |
| 1.3.6.1.4.1.664.2.141.9.29 | ScalaradDSUIQDCEInterfaceType | read-write | mandatory | This option enables or disables Answer Always for Dial Backup operation. If enabled, the answer unit answers any incoming call regardless of failed conditions. |
| 1.3.6.1.4.1.664.2.141.9.30 | ScalaradDSUIQDCEBitRate | read-write | mandatory | This option is uses for utilization measurement of the DBU port when an external DCE device is used. Set this parameter in KBPS close to the connection rate. |
| 1.3.6.1.4.1.664.2.141.10 | NodeadDSUIQIntDBUStatus | |||
| 1.3.6.1.4.1.664.2.141.10.1 | TableadDSUIQIntDBUStatusTable | not-accessible | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.10.1.1 | RowadDSUIQIntDBUStatusEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.10.1.1.1 | ColumnadDSUIQIntDBUSlotIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.10.1.1.2 | ColumnadDSUIQIntDBUFramesRx | read-only | mandatory | The number of Frames the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.3 | ColumnadDSUIQIntDBUFramesTx | read-only | mandatory | The number of Frames the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.4 | ColumnadDSUIQIntDBUBytesRx | read-only | mandatory | The number of Bytes the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.5 | ColumnadDSUIQIntDBUBytesTx | read-only | mandatory | The number of Bytes the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.6 | ColumnadDSUIQIntDBUAvgThruputTx | read-only | mandatory | The Average Throughput the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.7 | ColumnadDSUIQIntDBUAvgThruputRx | read-only | mandatory | The Average Throughput the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.8 | ColumnadDSUIQIntDBUMaxThruputTx | read-only | mandatory | The Maximum Throughput the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.9 | ColumnadDSUIQIntDBUMaxThruputRx | read-only | mandatory | The Maximum Throughput the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.10 | ColumnadDSUIQIntDBUAvgUtilizationTx | read-only | mandatory | The Average Utilization the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.11 | ColumnadDSUIQIntDBUAvgUtilizationRx | read-only | mandatory | The Average Utilization the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.12 | ColumnadDSUIQIntDBUMaxUtilizationTx | read-only | mandatory | The Maximum Utilization the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.13 | ColumnadDSUIQIntDBUMaxUtilizationRx | read-only | mandatory | The Maximum Utilization the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.10.1.1.14 | ColumnadDSUIQIntTimeInDBU | read-only | mandatory | Time in seconds the DBU port was active. |
| 1.3.6.1.4.1.664.2.141.10.1.1.15 | ColumnadDSUIQIntDBUCrcErrors | read-only | mandatory | Number of frames received with CRC errors. |
| 1.3.6.1.4.1.664.2.141.10.1.1.16 | ColumnadDSUIQIntDBUAbortFrames | read-only | mandatory | Number of frames received without proper flag termination. |
| 1.3.6.1.4.1.664.2.141.10.1.1.17 | ColumnadDSUIQIntDBUOctectViolations | read-only | mandatory | Number of frames received with a bit count not divisible by eigth. |
| 1.3.6.1.4.1.664.2.141.10.1.1.18 | ColumnadDSUIQIntDBUDiscardFrames | read-only | mandatory | Number of frames discarded by the IQ unit |
| 1.3.6.1.4.1.664.2.141.10.1.1.19 | ColumnadDSUIQIntDBULengthErrors | read-only | mandatory | Number of frames received that is less than 5 bytes or greater than 4500 bytes. |
| 1.3.6.1.4.1.664.2.141.10.1.1.20 | ColumnadDSUIQIntDBUEncapsulationErrors | read-only | mandatory | Number of frames destined for the IQ IP stack with that does not meet the FRF.3 IA. |
| 1.3.6.1.4.1.664.2.141.10.1.1.21 | ColumnadDSUIQIntDBUUnroutable | read-only | mandatory | Number of frames received on a management DLCI destined for the IQ unit and have the wrong IP address. |
| 1.3.6.1.4.1.664.2.141.11 | NodeadDSUIQDayDBUStatus | |||
| 1.3.6.1.4.1.664.2.141.11.1 | TableadDSUIQDayDBUStatusTable | not-accessible | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.11.1.1 | RowadDSUIQDayDBUStatusEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.11.1.1.1 | ColumnadDSUIQDayDBUSlotIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.11.1.1.2 | ColumnadDSUIQDayDBUFramesRx | read-only | mandatory | The number of Frames the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.3 | ColumnadDSUIQDayDBUFramesTx | read-only | mandatory | The number of Frames the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.4 | ColumnadDSUIQDayDBUBytesRx | read-only | mandatory | The number of Bytes the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.5 | ColumnadDSUIQDayDBUBytesTx | read-only | mandatory | The number of Bytes the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.6 | ColumnadDSUIQDayDBUAvgThruputTx | read-only | mandatory | The Average Throughput the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.7 | ColumnadDSUIQDayDBUAvgThruputRx | read-only | mandatory | The Average Throughput the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.8 | ColumnadDSUIQDayDBUMaxThruputTx | read-only | mandatory | The Maximum Throughput the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.9 | ColumnadDSUIQDayDBUMaxThruputRx | read-only | mandatory | The Maximum Throughput the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.10 | ColumnadDSUIQDayDBUAvgUtilizationTx | read-only | mandatory | The Average Utilization the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.11 | ColumnadDSUIQDayDBUAvgUtilizationRx | read-only | mandatory | The Average Utilization the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.12 | ColumnadDSUIQDayDBUMaxUtilizationTx | read-only | mandatory | The Maximum Utilization the Port transmitted for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.13 | ColumnadDSUIQDayDBUMaxUtilizationRx | read-only | mandatory | The Maximum Utilization the Port received for the interval. |
| 1.3.6.1.4.1.664.2.141.11.1.1.14 | ColumnadDSUIQDayTimeInDBU | read-only | mandatory | Time in seconds the DBU port was active. |
| 1.3.6.1.4.1.664.2.141.11.1.1.15 | ColumnadDSUIQDayDBUCrcErrors | read-only | mandatory | Number of frames received with CRC errors. |
| 1.3.6.1.4.1.664.2.141.11.1.1.16 | ColumnadDSUIQDayDBUAbortFrames | read-only | mandatory | Number of frames received without proper flag termination. |
| 1.3.6.1.4.1.664.2.141.11.1.1.17 | ColumnadDSUIQDayDBUOctectViolations | read-only | mandatory | Number of frames received with a bit count not divisible by eigth. |
| 1.3.6.1.4.1.664.2.141.11.1.1.18 | ColumnadDSUIQDayDBUDiscardFrames | read-only | mandatory | Number of frames discarded by the IQ unit |
| 1.3.6.1.4.1.664.2.141.11.1.1.19 | ColumnadDSUIQDayDBULengthErrors | read-only | mandatory | Number of frames received that is less than 5 bytes or greater than 4500 bytes. |
| 1.3.6.1.4.1.664.2.141.11.1.1.20 | ColumnadDSUIQDayDBUEncapsulationErrors | read-only | mandatory | Number of frames destined for the IQ IP stack with that does not meet the FRF.3 IA. |
| 1.3.6.1.4.1.664.2.141.11.1.1.21 | ColumnadDSUIQDayDBUUnroutable | read-only | mandatory | Number of frames received on a management DLCI destined for the IQ unit and have the wrong IP address. |
| 1.3.6.1.4.1.664.2.141.12 | NodeadDSUIQTrapManager | |||
| 1.3.6.1.4.1.664.2.141.12.1 | TableadDSUIQTrapManagerTable | not-accessible | mandatory | The trap manger route table. |
| 1.3.6.1.4.1.664.2.141.12.1.1 | RowadDSUIQTrapManagerEntry | not-accessible | mandatory | n/a |
| 1.3.6.1.4.1.664.2.141.12.1.1.1 | ColumnadDSUIQTrapManagerRouteIndex | read-only | mandatory | n/a. |
| 1.3.6.1.4.1.664.2.141.12.1.1.2 | ColumnadDSUIQTrapManagerRouteIPAddress | read-write | mandatory | Sets the Trap Manager IP Address. |
| 1.3.6.1.4.1.664.2.141.12.1.1.3 | ColumnadDSUIQTrapManagerRouteDLCI | read-write | mandatory | Sets the Trap Manager DLCI. (Range 16 - 1007). |
| 1.3.6.1.4.1.664.2.141.12.1.1.4 | ColumnadDSUIQTrapManagerRoutePort | read-write | mandatory | Selects the Trap Manager Port. |