ALC-OPT-MIB
227 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises Gauge |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.449 | Nodecodex | |||
| 1.3.6.1.4.1.449.2 | NodecdxProductSpecific | |||
| 1.3.6.1.4.1.449.2.1 | Nodecdx6500 | |||
| 1.3.6.1.4.1.449.2.1.2 | Nodecdx6500Configuration | |||
| 1.3.6.1.4.1.449.2.1.2.1 | Nodecdx6500CfgProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1 | Nodecdx6500PCTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1.27 | Nodecdx6500PPCTALCCfgTable | |||
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1 | Tablecdx6500PPCTALCPortTable | not-accessible | mandatory | This table contains ALC Port configuration parameters |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1 | Rowcdx6500PPCTALCPortEntry | not-accessible | mandatory | Entries in the ALC Port Configuration Table. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.1 | ColumnalcPCfgPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.2 | ColumnalcPCfgPortType | read-only | mandatory | Port Type of this port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.3 | ColumnalcPCfgSubtype | read-only | mandatory | This is the ALC port subtype. alcHpad - Host PAD. alcTpad - Terminal PAD. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.4 | ColumnalcPCfgPortControl | read-only | mandatory | Specify any of the following port control options: simp : Simple connection with no control signal handshake. dtr : Connection with DTR control signal handshak… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.5 | ColumnalcPCfgClockSource | read-only | mandatory | int : Internal clock source. ext : External clock source. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.6 | ColumnalcPCfgClockSpeed | read-only | mandatory | This is the speed of the port in bits per second, when using internal clocking. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.7 | ColumnalcPCfgPollDelayTimer | read-only | mandatory | This is the delay in milliseconds to impose between poll cycles if no interchanges are polled. Valid on TPAD lines only. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.8 | ColumnalcPCfgHostTimeout | read-only | mandatory | On a poll coerced line, the host is considered to be down if a poll is not received within this time, specified in milliseconds. Valid on HPAD lines only. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.9 | ColumnalcPCfgMaxMesgSize | read-only | mandatory | This specifies the maximum size of messages that can be sent or received on this line excluding padding characters. TPAD may receive multiple messages in a fra… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.10 | ColumnalcPCfgMinIntrvlBetweenPolls | read-only | mandatory | The minimum length of time, in milliseconds, between polls issued on this line. Valid on TPAD lines only. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.11 | ColumnalcPCfgRtsCtsTimeout | read-only | mandatory | The time in milliseconds, within which CTS must be raised following the RTS signal. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.12 | ColumnalcPCfgLeadPadChar | read-only | mandatory | This is the character to use when inserting leading padding characters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.13 | ColumnalcPCfgNumLeadPadChars | read-only | mandatory | This is the number of leading padding characters to use. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.14 | ColumnalcPCfgTrailPadChar | read-only | mandatory | This is the character to use when inserting trailing padding characters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.15 | ColumnalcPCfgNumTrailPadChars | read-only | mandatory | This is the number of trailing padding characters to use. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.16 | ColumnalcPCfgALCLineOptions | read-only | mandatory | Select options on this ALC port as follows: NONE : no option specified EMB_SYNC : Sychronization characters are inserted between messages in the same frame. MA… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.17 | ColumnalcPCfgConnType | read-only | mandatory | none : No connection. x25 : Connection type is X.25. nc : Skipped during configuration |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.18 | ColumnalcPCfgAcallMnemonic | read-only | mandatory | This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is sp… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.19 | ColumnalcPCfgCallingAddress | read-only | mandatory | The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.20 | ColumnalcPCfgCUD | read-only | mandatory | The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.21 | ColumnalcPCfgNumOfBuffers | read-only | mandatory | This defines the number of buffers that are available for data transfer in each direction. Each buffer will hold one message. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.22 | ColumnalcPCfgInHeader | read-only | mandatory | This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these posit… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.23 | ColumnalcPCfgOutHeader | read-only | mandatory | This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.24 | ColumnalcPCfgReconnectTimeout | read-only | mandatory | The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.25 | ColumnalcPCfgInactivityTimeout | read-only | mandatory | The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.26 | ColumnalcPCfgDebounceTimeout | read-only | mandatory | This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.27 | ColumnalcPCfgParity | read-only | mandatory | none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.28 | ColumnalcPCfgConnOptions | read-only | mandatory | Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in whi… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.29 | ColumnalcPCfgAvailableMesg | read-only | mandatory | This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded … |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.30 | ColumnalcPCfgUnavailableMesg | read-only | mandatory | This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is de… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2 | Tablecdx6500PPCTALCInterchangeTable | not-accessible | mandatory | This table contains ALC Interchange configuration parameters |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1 | Rowcdx6500PPCTALCInterchangeEntry | not-accessible | mandatory | Entries in the ALC Interchange Configuration Table. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.1 | ColumnalcICfgPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.2 | ColumnalcICfgInterchangeAddress | read-only | mandatory | The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.3 | ColumnalcICfgOptionOnInvalidCCC | read-only | mandatory | The action to be taken on receipt of a message with an invalid ccc. discard : Discard the message ignore : Treat the message as correct. reenter : (TPAD only) … |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.4 | ColumnalcICfgGenTerminalAddress | read-only | mandatory | Specifies the terminal address to which broadcast messages are sent when the GTA option is specified. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.5 | ColumnalcICfgHostTimeout | read-only | mandatory | The host is considered to be down if a poll is not received within this period, which is specified in milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.6 | ColumnalcICfgMaxComponentsPerFrame | read-only | mandatory | Specifies the maximum number of message segments transmitted in one frame (HPAD) or expected in one frame (TPAD). |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.7 | ColumnalcICfgFastPollCycleCount | read-only | mandatory | The polling rate for an interchange in fast poll. A poll is issued to this interchange once in every n poll cycles on the line. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.8 | ColumnalcICfgSlowPollCycleCount | read-only | mandatory | The polling rate for an interchange in slow poll. One slow poll IA is polled every n poll cycles on the line. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.9 | ColumnalcICfgN1Counter | read-only | mandatory | The number of polls that can be sent without receiving a response before the interchange enters slow poll. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.10 | ColumnalcICfgN2Counter | read-only | mandatory | The number of good poll responses required before the interchange enters fast poll. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.11 | ColumnalcICfgT1Timeout | read-only | mandatory | The time, in milliseconds, within which an interchange must start responding to a poll. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.12 | ColumnalcICfgT2Timeout | read-only | mandatory | The time, in milliseconds, within which an interchange must complete its transmission. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.13 | ColumnalcICfgReenterMessage | read-only | mandatory | This specifies the text of a message sent to terminals when a message with an incorrect ccc is received and the action on receipt of an invalid ccc is REENTER.… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.14 | ColumnalcICfgStartMessage | read-only | mandatory | This specifies the text of a message sent to terminals when polling of this interchange is started and the STST option is configured. Note that some terminals … |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.15 | ColumnalcICfgStopMessage | read-only | mandatory | This specifies the text of a message sent to terminals when polling of this interchange is stopped and the STST option is configured. Note that some terminals … |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.16 | ColumnalcICfgOptions | read-only | mandatory | Select options on this ALC Interchange as follows : NONE : no option specified GTA : (TPAD only) Indicates that there is a general terminal address which may b… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.17 | ColumnalcICfgValidTAList | read-only | mandatory | A list of hexadecimal numbers between 1 and 3F separated by commas. /f or /r after each is used to indicate forward or reverse abort respectively. Ranges may b… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.18 | ColumnalcICfgConnType | read-only | mandatory | none : No connection. x25 : Connection type is X.25. nc : Skipped during configuration |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.19 | ColumnalcICfgAcallMnemonic | read-only | mandatory | This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is sp… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.20 | ColumnalcICfgCallingAddress | read-only | mandatory | The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.21 | ColumnalcICfgCUD | read-only | mandatory | The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.22 | ColumnalcICfgNumOfBuffers | read-only | mandatory | This defined the number of buffers that are available for data transfer in each direction. Each buffer will hold one message. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.23 | ColumnalcICfgInHeader | read-only | mandatory | This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these posit… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.24 | ColumnalcICfgOutHeader | read-only | mandatory | This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.25 | ColumnalcICfgReconnectTimeout | read-only | mandatory | The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.26 | ColumnalcICfgInactivityTimeout | read-only | mandatory | The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.27 | ColumnalcICfgDebounceTimeout | read-only | mandatory | This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.28 | ColumnalcICfgParity | read-only | mandatory | none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.29 | ColumnalcICfgConnOptions | read-only | mandatory | Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in whi… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.30 | ColumnalcICfgAvailableMesg | read-only | mandatory | This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded … |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.31 | ColumnalcICfgUnavailableMesg | read-only | mandatory | This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is de… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3 | Tablecdx6500PPCTALCTerminalTable | not-accessible | mandatory | This table contains ALC Terminal configuration parameters |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1 | Rowcdx6500PPCTALCTerminalEntry | not-accessible | mandatory | Entries in the ALC Terminal Configuration Table. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.1 | ColumnalcTCfgPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.2 | ColumnalcTCfgInterchangeAddress | read-only | mandatory | The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.3 | ColumnalcTCfgTerminalAddress | read-only | mandatory | Address identifying this terminal. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.4 | ColumnalcTCfgConnType | read-only | mandatory | none : No connection type. x25 : Connection type is X.25. nc : Skipped during configuration |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.5 | ColumnalcTCfgAcallMnemonic | read-only | mandatory | This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is sp… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.6 | ColumnalcTCfgCallingAddress | read-only | mandatory | The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.7 | ColumnalcTCfgCUD | read-only | mandatory | The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.8 | ColumnalcTCfgNumOfBuffers | read-only | mandatory | This defined the number of buffers that are available for data transfer in each direction. Each buffer will hold one message. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.9 | ColumnalcTCfgInHeader | read-only | mandatory | This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these posit… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.10 | ColumnalcTCfgOutHeader | read-only | mandatory | This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.11 | ColumnalcTCfgReconnectTimeout | read-only | mandatory | The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.12 | ColumnalcTCfgInactivityTimeout | read-only | mandatory | The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.13 | ColumnalcTCfgDebounceTimeout | read-only | mandatory | This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately. |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.14 | ColumnalcTCfgParity | read-only | mandatory | none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.15 | ColumnalcTCfgConnOptions | read-only | mandatory | Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in whi… |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.16 | ColumnalcTCfgAvailableMesg | read-only | mandatory | This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded … |
| 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.17 | ColumnalcTCfgUnavailableMesg | read-only | mandatory | This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is de… |
| 1.3.6.1.4.1.449.2.1.3 | Nodecdx6500Statistics | |||
| 1.3.6.1.4.1.449.2.1.3.1 | Nodecdx6500StatProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1 | Nodecdx6500PSTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.28 | Nodecdx6500PPSTALCStatsTable | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1 | Tablecdx6500PPSTALCPortTable | not-accessible | mandatory | This table contains ALC Port Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1 | Rowcdx6500PPSTALCPortEntry | not-accessible | mandatory | Entries in the ALC Port Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.1 | ColumnalcPStatsPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.2 | ColumnalcPStatsPortType | read-only | mandatory | Port type of this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.3 | ColumnalcPStatsPortState | read-only | mandatory | Current Port State. connecting:The line has been enabled by the operator, but polling has not yet been established. online :The line is active. offline :The li… |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.4 | ColumnalcPStatsFramesIn | read-only | mandatory | Number of frames received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.5 | ColumnalcPStatsFramesOut | read-only | mandatory | Number of frames transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.6 | ColumnalcPStatsDataMesgsIn | read-only | mandatory | Number of data messages received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.7 | ColumnalcPStatsDataMesgsOut | read-only | mandatory | Number of data messages transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.8 | ColumnalcPStatsCharsIn | read-only | mandatory | Number of characters received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.9 | ColumnalcPStatsCharsOut | read-only | mandatory | Number of characters transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.10 | ColumnalcPStatsPolls | read-only | mandatory | Number of polls transmitted or received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.11 | ColumnalcPStatsGAs | read-only | mandatory | Number of Go Ahead messages transmitted or received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.12 | ColumnalcPStatsResets | read-only | mandatory | Number of Reset messages transmitted or received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.13 | ColumnalcPStatsDiscardBadIAIn | read-only | mandatory | Number of received messages discarded due to bad Interchange Address. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.14 | ColumnalcPStatsDiscardBadIAOut | read-only | mandatory | Number of transmitted messages discarded due to bad Interchange Address. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.15 | ColumnalcPStatsMaxQSizeOut | read-only | mandatory | Maximum transmit queue size. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.16 | ColumnalcPStatsCCCErrors | read-only | mandatory | Number of messages received with an invalid checksum. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.17 | ColumnalcPStatsSignalLosses | read-only | mandatory | Number of Signal Losses. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.18 | ColumnalcPStatsOverlengthFrames | read-only | mandatory | Number of overlength frames received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.19 | ColumnalcPStatsPortStatus | read-only | mandatory | Current Port Status. na :Value not Available |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.20 | ColumnalcPStatsConnState | read-only | mandatory | Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:Th… |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.21 | ColumnalcPStatsALCMesgsIn | read-only | mandatory | The number of messages received from ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.22 | ColumnalcPStatsALCMesgsOut | read-only | mandatory | The number of messages transmitted to ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.23 | ColumnalcPStatsX25MesgsIn | read-only | mandatory | The number of messages received from X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.24 | ColumnalcPStatsX25MesgsOut | read-only | mandatory | The number of messages transmitted to X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.25 | ColumnalcPStatsALCCharsIn | read-only | mandatory | The number of characters received from ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.26 | ColumnalcPStatsALCCharsOut | read-only | mandatory | The number of characters transmitted to ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.27 | ColumnalcPStatsX25CharsIn | read-only | mandatory | The number of characters received from X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.28 | ColumnalcPStatsX25CharsOut | read-only | mandatory | The number of characters transmitted to X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.29 | ColumnalcPStatsALCDiscardedMesgsEntityDown | read-only | mandatory | The number of messages received by ALC for which the destination entity is unable to process the data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.30 | ColumnalcPStatsX25DiscardedMesgsEntityDown | read-only | mandatory | The number of messages received by X.25 for which the destination entity is unable to process the data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.31 | ColumnalcPStatsX25DiscardedMesgsBadALCAddr | read-only | mandatory | The number of messages received from X.25 for which the addresses specified do not match those associated with the connection. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.32 | ColumnalcPStatsX25DiscardedMesgsBadHeader | read-only | mandatory | The number of messages received by X.25 of which the IN header configured does not match the header present in the message. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.33 | ColumnalcPStatsX25DiscardedMesgsTooLong | read-only | mandatory | The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.34 | ColumnalcPStatsALCDiscardedMesgsQFull | read-only | mandatory | The number of messages discarded because the ALC outbound message queue was full. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.35 | ColumnalcPStatsX25DiscardedMesgsQFull | read-only | mandatory | The number of messages discarded because the X.25 outbound message queue was full. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.36 | ColumnalcPStatsCurrTxALCQSize | read-only | mandatory | The number of messages currently queued in the ALC outbound message queue for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.37 | ColumnalcPStatsCurrTxX25QSize | read-only | mandatory | The number of messages currently queued in the X.25 outbound message queue for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.38 | ColumnalcPStatsMaxTxALCQSize | read-only | mandatory | The maximum (highwater mark) size of the ALC outbound queue so far. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.39 | ColumnalcPStatsMaxTxX25QSize | read-only | mandatory | The maximum (highwater mark) size of the X.25 outbound queue so far. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2 | Tablecdx6500PPSTALCInterchangeTable | not-accessible | mandatory | This table contains ALC Interchange Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1 | Rowcdx6500PPSTALCInterchangeEntry | not-accessible | mandatory | Entries in the ALC Interchange Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.1 | ColumnalcIStatsPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.2 | ColumnalcIStatsInterchangeAddress | read-only | mandatory | The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.3 | ColumnalcIStatsInterchangeState | read-only | mandatory | Current State of this Interchange. online :The interchange is active. This is displayed for HPAD interchanges, and TPAD interchanges configured as NOPOLL, only… |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.4 | ColumnalcIStatsFramesIn | read-only | mandatory | Number of ALC frames received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.5 | ColumnalcIStatsFramesOut | read-only | mandatory | Number of ALC frames transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.6 | ColumnalcIStatsDataMesgsIn | read-only | mandatory | Number of ALC data messages received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.7 | ColumnalcIStatsDataMesgsOut | read-only | mandatory | Number of ALC data messages transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.8 | ColumnalcIStatsCharsIn | read-only | mandatory | Total number of characters received, excluding synchronization characters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.9 | ColumnalcIStatsCharsOut | read-only | mandatory | Total number of characters transmitted, excluding synchronization characters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.10 | ColumnalcIStatsPolls | read-only | mandatory | The number of poll messages transmitted for a line defined as a TPAD. The number received for one defined as HPAD. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.11 | ColumnalcIStatsGAs | read-only | mandatory | The number of Go Ahead messages transmitted for a line defined as HPAD. The number received for one defined as TPAD. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.12 | ColumnalcIStatsResets | read-only | mandatory | The number of Reset messages transmitted for a line defined as TPAD. The number received for one defined as HPAD. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.13 | ColumnalcIStatsDiscardBadTAIn | read-only | mandatory | The number of received messages discarded because the Terminal Address was not defined. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.14 | ColumnalcIStatsDiscardBadTAOut | read-only | mandatory | The number of transmitted messages discarded because the Terminal Address was not defined. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.15 | ColumnalcIStatsDisabledIAIn | read-only | mandatory | The number of received messages discarded because the Interchange was disabled. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.16 | ColumnalcIStatsDisabledIAOut | read-only | mandatory | The number of transmitted messages discarded because the Interchange was disabled. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.17 | ColumnalcIStatsMaxQSizeOut | read-only | mandatory | Maximum number of frames queued for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.18 | ColumnalcIStatsCCCErrors | read-only | mandatory | Number of messages received with an invalid checksum. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.19 | ColumnalcIStatsT1Timeouts | read-only | mandatory | Number of T1 timer expirations. This is defined for TPAD only. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.20 | ColumnalcIStatsT2Timeouts | read-only | mandatory | Number of T2 timer expirations. This is defined for TPAD only. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.21 | ColumnalcIStatsConnState | read-only | mandatory | Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:Th… |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.22 | ColumnalcIStatsALCMesgsIn | read-only | mandatory | The number of messages received from ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.23 | ColumnalcIStatsALCMesgsOut | read-only | mandatory | The number of messages transmitted to ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.24 | ColumnalcIStatsX25MesgsIn | read-only | mandatory | The number of messages received from X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.25 | ColumnalcIStatsX25MesgsOut | read-only | mandatory | The number of messages transmitted to X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.26 | ColumnalcIStatsALCCharsIn | read-only | mandatory | The number of characters received from ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.27 | ColumnalcIStatsALCCharsOut | read-only | mandatory | The number of characters transmitted to ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.28 | ColumnalcIStatsX25CharsIn | read-only | mandatory | The number of characters received from X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.29 | ColumnalcIStatsX25CharsOut | read-only | mandatory | The number of characters transmitted to X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.30 | ColumnalcIStatsALCDiscardedMesgsEntityDown | read-only | mandatory | The number of messages received by ALC for which the destination entity is unable to process the data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.31 | ColumnalcIStatsX25DiscardedMesgsEntityDown | read-only | mandatory | The number of messages received by X.25 for which the destination entity is unable to process the data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.32 | ColumnalcIStatsX25DiscardedMesgsBadALCAddr | read-only | mandatory | The number of messages received from X.25 for which the addresses specified do not match those associated with the connection. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.33 | ColumnalcIStatsX25DiscardedMesgsBadHeader | read-only | mandatory | The number of messages received by X.25 of which the IN header configured does not match the header present in the message. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.34 | ColumnalcIStatsX25DiscardedMesgsTooLong | read-only | mandatory | The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.35 | ColumnalcIStatsALCDiscardedMesgsQFull | read-only | mandatory | The number of messages discarded because the ALC outbound message queue was full. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.36 | ColumnalcIStatsX25DiscardedMesgsQFull | read-only | mandatory | The number of messages discarded because the X.25 outbound message queue was full. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.37 | ColumnalcIStatsCurrTxALCQSize | read-only | mandatory | The number of messages currently queued in the ALC outbound message queue for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.38 | ColumnalcIStatsCurrTxX25QSize | read-only | mandatory | The number of messages currently queued in the X.25 outbound message queue for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.39 | ColumnalcIStatsMaxTxALCQSize | read-only | mandatory | The maximum (highwater mark) size of the ALC outbound queue so far. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.40 | ColumnalcIStatsMaxTxX25QSize | read-only | mandatory | The maximum (highwater mark) size of the X.25 outbound queue so far. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3 | Tablecdx6500PPSTALCTerminalTable | not-accessible | mandatory | This table contains ALC Terminalinal Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1 | Rowcdx6500PPSTALCTerminalEntry | not-accessible | mandatory | Entries in the ALC Terminalinal Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.1 | ColumnalcTStatsPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.2 | ColumnalcTStatsInterchangeAddress | read-only | mandatory | The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.3 | ColumnalcTStatsTerminalAddress | read-only | mandatory | Address identifying this terminal. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.4 | ColumnalcTStatsConnState | read-only | mandatory | Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:Th… |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.5 | ColumnalcTStatsALCMesgsIn | read-only | mandatory | The number of messages received from ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.6 | ColumnalcTStatsALCMesgsOut | read-only | mandatory | The number of messages transmitted to ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.7 | ColumnalcTStatsX25MesgsIn | read-only | mandatory | The number of messages received from X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.8 | ColumnalcTStatsX25MesgsOut | read-only | mandatory | The number of messages transmitted to X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.9 | ColumnalcTStatsALCCharsIn | read-only | mandatory | The number of characters received from ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.10 | ColumnalcTStatsALCCharsOut | read-only | mandatory | The number of characters transmitted to ALC. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.11 | ColumnalcTStatsX25CharsIn | read-only | mandatory | The number of characters received from X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.12 | ColumnalcTStatsX25CharsOut | read-only | mandatory | The number of characters transmitted to X.25. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.13 | ColumnalcTStatsALCDiscardedMesgsEntityDown | read-only | mandatory | The number of messages received by ALC for which the destination entity is unable to process the data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.14 | ColumnalcTStatsX25DiscardedMesgsEntityDown | read-only | mandatory | The number of messages received by X.25 for which the destination entity is unable to process the data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.15 | ColumnalcTStatsX25DiscardedMesgsBadALCAddr | read-only | mandatory | The number of messages received from X.25 for which the addresses specified do not match those associated with the connection. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.16 | ColumnalcTStatsX25DiscardedMesgsBadHeader | read-only | mandatory | The number of messages received by X.25 of which the IN header configured does not match the header present in the message. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.17 | ColumnalcTStatsX25DiscardedMesgsTooLong | read-only | mandatory | The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.18 | ColumnalcTStatsALCDiscardedMesgsQFull | read-only | mandatory | The number of messages discarded because the ALC outbound message queue was full. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.19 | ColumnalcTStatsX25DiscardedMesgsQFull | read-only | mandatory | The number of messages discarded because the X.25 outbound message queue was full. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.20 | ColumnalcTStatsCurrTxALCQSize | read-only | mandatory | The number of messages currently queued in the ALC outbound message queue for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.21 | ColumnalcTStatsCurrTxX25QSize | read-only | mandatory | The number of messages currently queued in the X.25 outbound message queue for transmission. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.22 | ColumnalcTStatsMaxTxALCQSize | read-only | mandatory | The maximum (highwater mark) size of the ALC outbound queue so far. |
| 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.23 | ColumnalcTStatsMaxTxX25QSize | read-only | mandatory | The maximum (highwater mark) size of the X.25 outbound queue so far. |
| 1.3.6.1.4.1.449.2.1.4 | Nodecdx6500Controls | |||
| 1.3.6.1.4.1.449.2.1.4.10 | Nodecdx6500ContALC | |||
| 1.3.6.1.4.1.449.2.1.4.10.1 | Tablecdx6500ContALCPortTable | not-accessible | mandatory | This table contains ALC Port Control parameters. |
| 1.3.6.1.4.1.449.2.1.4.10.1.1 | Rowcdx6500ContALCPortEntry | not-accessible | mandatory | Entries in the ALC Port Control Table. |
| 1.3.6.1.4.1.449.2.1.4.10.1.1.1 | ColumnalcPContPortNumber | not-accessible | mandatory | ALC Port Number. |
| 1.3.6.1.4.1.449.2.1.4.10.1.1.2 | ColumnalcPContPortBoot | write-only | mandatory | Boots the specified ALC Port. boot - Boot the port. noBoot - Do not boot the port. |
| 1.3.6.1.4.1.449.2.1.4.10.1.1.3 | ColumnalcPContPortEnable | write-only | mandatory | Enables the specified ALC Port. enable - Enable the port. noEnable - Do not enable the port. |
| 1.3.6.1.4.1.449.2.1.4.10.1.1.4 | ColumnalcPContPortDisable | write-only | mandatory | Disables the specified ALC Port. disable - Disable the port. noDisable - Do not disable the port. |
| 1.3.6.1.4.1.449.2.1.4.10.2 | Tablecdx6500ContALCInterchangeTable | not-accessible | mandatory | This table contains ALC Interchange Control parameters. |
| 1.3.6.1.4.1.449.2.1.4.10.2.1 | Rowcdx6500ContALCInterchangeEntry | not-accessible | mandatory | Entries in the ALC Interchange Control Table. |
| 1.3.6.1.4.1.449.2.1.4.10.2.1.1 | ColumnalcIContPortNumber | not-accessible | mandatory | ALC Port Number. |
| 1.3.6.1.4.1.449.2.1.4.10.2.1.2 | ColumnalcIContInterchangeAddress | not-accessible | mandatory | ALC Interchange address. |
| 1.3.6.1.4.1.449.2.1.4.10.2.1.3 | ColumnalcIContInterchangeBoot | write-only | mandatory | Boots the specified ALC Interchange. boot - Boot the interchange. noBoot - Do not boot the interchange. |
| 1.3.6.1.4.1.449.2.1.4.10.2.1.4 | ColumnalcIContInterchangeEnable | write-only | mandatory | Enables the specified ALC Interchange. enable - Enable the interchange. noEnable - Do not enable the interchange. |
| 1.3.6.1.4.1.449.2.1.4.10.2.1.5 | ColumnalcIContInterchangeDisable | write-only | mandatory | Disables the specified ALC Interchange. disable - Disable the interchange. noDisable - Do not disable the interchange. |
| 1.3.6.1.4.1.449.2.1.4.10.3 | Tablecdx6500ContALCTerminalTable | not-accessible | mandatory | This table contains ALC Terminal Control parameters. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1 | Rowcdx6500ContALCTerminalEntry | not-accessible | mandatory | Entries in the ALC Terminal Control Table. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1.1 | ColumnalcTContPortNumber | not-accessible | mandatory | ALC Port Number. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1.2 | ColumnalcTContInterchangeAddress | not-accessible | mandatory | ALC Interchange address. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1.3 | ColumnalcTContTerminalAddress | not-accessible | mandatory | Address identifying this terminal. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1.4 | ColumnalcTContTerminalBoot | write-only | mandatory | Boots the specified ALC terminal. boot - Boot the terminal. noBoot - Do not boot the terminal. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1.5 | ColumnalcTContTerminalEnable | write-only | mandatory | Enables the specified ALC Terminal. enable - Enable the terminal. noEnable - Do not enable the terminal. |
| 1.3.6.1.4.1.449.2.1.4.10.3.1.6 | ColumnalcTContTerminalDisable | write-only | mandatory | Disables the specified ALC terminal. disable - Disable the terminal. noDisable - Do not disable the terminal. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING |