ASCEND-CALL-LOGGING-MIB
18 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.529.25.1 | ScalarcallLoggingNumServers | read-only | mandatory | The maximum number of Call Logging servers supported by the system. |
| 1.3.6.1.4.1.529.25.2 | TablecallLoggingServerTable | not-accessible | mandatory | A list of entries for Call Logging Server addresses. |
| 1.3.6.1.4.1.529.25.2.1 | RowcallLoggingServerEntry | not-accessible | mandatory | Entry holding information about the currently active Call Logging Server and the address of a Server. |
| 1.3.6.1.4.1.529.25.2.1.1 | ColumncallLoggingServerIndex | read-only | mandatory | The index number for this Call Logging server entry. Its value ranges from 1 to 'callLoggingNumServers'. and identifies which server entry is associated with. |
| 1.3.6.1.4.1.529.25.2.1.2 | ColumncallLoggingCurrentServerFlag | read-only | mandatory | Value indicates whether this entry is the current Call Logging server or not. |
| 1.3.6.1.4.1.529.25.2.1.3 | ColumncallLoggingServerIPAddress | read-write | mandatory | The IP address of Call Logging server. The value 0.0.0.0 is returned if entry is invalid. |
| 1.3.6.1.4.1.529.25.2.1.4 | ColumncallLoggingEnableActiveServer | read-write | mandatory | This is used to set the active call Logging server. If set to enable(2) it will enable the call Logging server, A read on the variable will return notApplicabl… |
| 1.3.6.1.4.1.529.25.3 | ScalarcallLoggingStatus | read-write | mandatory | Enable/Disable call loggin support. Note: Prior to enable the call Logging, one of the Call Logging server must be setup with a valid IP address. If the server… |
| 1.3.6.1.4.1.529.25.4 | ScalarcallLoggingPortNumber | read-write | mandatory | The UDP server port to use for Call Logging packets. |
| 1.3.6.1.4.1.529.25.5 | ScalarcallLoggingKey | read-write | mandatory | The (RADIUS_ACCT) call logging key to access server. |
| 1.3.6.1.4.1.529.25.6 | ScalarcallLoggingTimeout | read-write | mandatory | Number of seconds to wait for a response to previous Call Logging request sent to server. |
| 1.3.6.1.4.1.529.25.7 | ScalarcallLoggingIdBase | read-write | mandatory | The Base to use in reporting Call Logging ID. |
| 1.3.6.1.4.1.529.25.8 | ScalarcallLoggingResetTime | read-write | mandatory | The time to reset to the primary server after it has failed. |
| 1.3.6.1.4.1.529.25.9 | ScalarcallLoggingStopPacketsOnly | read-write | mandatory | Send call log Stop packets that have username=0. These are caused by connections that are dropped before authentication is done. |
| 1.3.6.1.4.1.529.25.10 | ScalarcallLoggingRetryLimit | read-write | mandatory | Number of retries before removing Call Logging packet. 0 means leave on retry list until maximum retry entries are exceeded. |
| 1.3.6.1.4.1.529.25.11 | ScalarcallLoggingAssStatus | read-write | mandatory | Indicates the status of Active Session Snapshot protocol. Writing the attribute with a nonzero value causes the start of an Active Session Snapshot. If no serv… |
| 1.3.6.1.4.1.529.25.12 | ScalarcallLoggingDroppedPacketCount | read-only | mandatory | Number of dropped Call Logging packets since the last Active Session Snapshot |
| 1.3.6.1.4.1.529.25.13 | ScalarcallLoggingRadCompatMode | read-only | mandatory | Indicates call logging RADIUS compatibility mode. This variable is deprecated, starting with TAOS Release 8.0. this variable has a fixed value of radVendorSpec… |