AirPair-MIB
572 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | ifIndex OBJECT-TYPE |
| RFC1155-SMI | Counter Gauge IpAddress TimeTicks |
| SNMPv2-MIB | snmp |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3 | Nodeorg | |||
| 1.3.6 | Nodedod | |||
| 1.3.6.1 | Nodeinternet | |||
| 1.3.6.1.2.1.11.0 | NodecoldStart | A coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation … | ||
| 1.3.6.1.2.1.11.1 | NodelinkDown | A linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration. | ||
| 1.3.6.1.2.1.11.2 | NodelinkUp | A linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up. | ||
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.7262 | Nodedragonwave | |||
| 1.3.6.1.4.1.7262.1 | NodeairPair | |||
| 1.3.6.1.4.1.7262.1.1 | ScalarapResetSystem | write-only | mandatory | Writing '1' to this object resets the NIC, Modem, and radio. |
| 1.3.6.1.4.1.7262.1.2 | ScalarapSaveMIB | write-only | mandatory | Writing '1' to this object save all MIB values. Note: If the AirPair type is 'airpair120' or 'airpair170' and the radio band doesn't match the AirPair type, Mi… |
| 1.3.6.1.4.1.7262.1.3 | ScalarapAdminStatus | read-write | mandatory | NOT IMPLEMENTED The desired state of the system. 'testing' and 'down' indicates that no user packet data can be passed.'down' disables the transmitter, while '… |
| 1.3.6.1.4.1.7262.1.4 | ScalarapOperStatus | read-only | mandatory | The current operational state of the system. Testing indicates that no operational packets can be passed. |
| 1.3.6.1.4.1.7262.1.5 | ScalarapAirInterfaceEncryption | read-only | mandatory | OBSOLETE. This enables encryption on the air interface. |
| 1.3.6.1.4.1.7262.1.6 | ScalarapMibVersionNumber | read-only | mandatory | The version number of the MIB. |
| 1.3.6.1.4.1.7262.1.7 | ScalarapType | read-only | mandatory | Indicates the specific type of system this is. |
| 1.3.6.1.4.1.7262.1.8 | ScalarapSpeed | read-write | mandatory | Changes the working speed of the Airpair. Writes are only valid if system is a FLEX. Due to backwards compatibility issue, 0 value should be treated as 0 Mbps. |
| 1.3.6.1.4.1.7262.1.9 | ScalarapMaxSpeed | read-only | mandatory | Indicates the maximum speed that this system can operate at. Due to backwards compatibility issue, 0 value should be treated as 0 Mbps. |
| 1.3.6.1.4.1.7262.1.10 | ScalarapKey | write-only | mandatory | Enter your AirPairFLEX key here along with the maximum speed for that key to upgrade the FLEX system. Format: [speed] [key] Example: 50 abc123 |
| 1.3.6.1.4.1.7262.1.11 | NodeapAuthentication | |||
| 1.3.6.1.4.1.7262.1.11.1 | ScalaruniquePeerAuthenticationKey | read-write | mandatory | The serial number of the peer node that this node will communicate with. This is only used when authentication mode is set to unique. |
| 1.3.6.1.4.1.7262.1.11.2 | ScalarpeerDetectedSerialNumber | read-only | mandatory | The serial number of the peer node that the system is presently communicating with. This is only used when authentication is set to unique. |
| 1.3.6.1.4.1.7262.1.11.3 | ScalarauthenticationMode | read-write | mandatory | This sets the authentication mode for the system.If configured for unique authentication, an AIRPAIR node only exchanges user traffic with one other AIRPAIR no… |
| 1.3.6.1.4.1.7262.1.11.4 | ScalarauthenticationFailureAction | read-write | mandatory | This sets the authentication failure action for the system. Block traffic will block all user traffic including remote management access. Pass traffic will all… |
| 1.3.6.1.4.1.7262.1.11.5 | ScalarpeerAuthenticationStatus | read-only | mandatory | Specifies the current authentication status of the system. Authenticated means authentication is on and the system has been authenticated, notAuthenticated mea… |
| 1.3.6.1.4.1.7262.1.12 | NodeapNetworkInterfaceCard | |||
| 1.3.6.1.4.1.7262.1.12.1 | ScalarnetworkInterfaceDesc | read-only | mandatory | A textual string containing information about the modem. Includes the manufacturer, product name, software version, and hardware version of the modem card. |
| 1.3.6.1.4.1.7262.1.12.2 | ScalaripAddress | read-only | mandatory | The IP Address of the network interface card. |
| 1.3.6.1.4.1.7262.1.12.3 | ScalarsubnetMask | read-only | mandatory | The subnet mask for the network interface card. |
| 1.3.6.1.4.1.7262.1.12.4 | ScalardefaultGateway | read-only | mandatory | The default gateway for the network interface card |
| 1.3.6.1.4.1.7262.1.12.5 | ScalarautoNegotiationSetup | read-write | mandatory | Turns auto-negotiation on or off. Turning off results in the interface defaulting to 100BaseT, Full Duplex. |
| 1.3.6.1.4.1.7262.1.12.6 | ScalarnegotiatedLinkParameters | read-only | mandatory | Displays the Interface card current operating negotiated parameters. |
| 1.3.6.1.4.1.7262.1.12.7 | ScalarminimumNegotiableLinkParameters | read-only | mandatory | Displays the minimum negotiable parameter set for the enet interface. |
| 1.3.6.1.4.1.7262.1.12.8 | ScalarserialNumber | read-only | mandatory | The Serial number of the network interface card. |
| 1.3.6.1.4.1.7262.1.12.9 | ScalarsnmpSetRequests | read-only | mandatory | Indicates whether SNMP SET requests are allowed. |
| 1.3.6.1.4.1.7262.1.12.10 | ScalarhttpAccessMode | read-write | mandatory | NOT IMPLEMENTED Indicates whether HTTP access is allowed. |
| 1.3.6.1.4.1.7262.1.12.11 | ScalartelnetAccessMode | read-write | mandatory | Indicates whether Telnet access is allowed. |
| 1.3.6.1.4.1.7262.1.12.12 | ScalardnsServer | read-write | mandatory | NOT IMPLEMENTED Indicates the DNS for the system. |
| 1.3.6.1.4.1.7262.1.12.13 | ScalarvlanTagging | read-write | mandatory | Indicates whether VLAN tagging is enabled. |
| 1.3.6.1.4.1.7262.1.12.14 | ScalarvlanTag | read-write | mandatory | The first two bytes are set to 0x8100. The two byte control tag is set by the user. |
| 1.3.6.1.4.1.7262.1.12.15 | NodenicStatistics | |||
| 1.3.6.1.4.1.7262.1.12.15.1 | ScalarnicFramesIn | read-only | mandatory | The current count of NIC frames received. |
| 1.3.6.1.4.1.7262.1.12.15.2 | ScalarnicFramesOut | read-only | mandatory | The current count of NIC frames sent. |
| 1.3.6.1.4.1.7262.1.12.15.3 | ScalarnicFramesInError | read-only | mandatory | The current count of NIC frames received in error. |
| 1.3.6.1.4.1.7262.1.12.15.4 | ScalarnicUndersizedFramesIn | read-only | mandatory | The current count of undersized NIC frames received. |
| 1.3.6.1.4.1.7262.1.12.15.5 | ScalarnicOversizedFramesIn | read-only | mandatory | The current count of oversized NIC frames received. |
| 1.3.6.1.4.1.7262.1.12.15.6 | ScalarnicFramesInQueue1Discarded | read-only | mandatory | The current count of NIC frames received in queue 2 that were discarded, but due to an error. One possible reason is lack of buffer space. |
| 1.3.6.1.4.1.7262.1.12.15.7 | ScalarnicFramesInQueue2Discarded | read-only | mandatory | The current count of NIC frames received in queue 2 that were discarded, but due to an error. One possible reason is lack of buffer space. |
| 1.3.6.1.4.1.7262.1.12.15.8 | ScalarnicFramesInQueue1 | read-only | mandatory | The current count of NIC frames passed through queue 1. |
| 1.3.6.1.4.1.7262.1.12.15.9 | ScalarnicFramesInQueue2 | read-only | mandatory | The current count of NIC frames passed through queue 2. |
| 1.3.6.1.4.1.7262.1.12.15.10 | ScalarnicFramesInQueue3 | read-only | mandatory | The current count of NIC frames passed through queue 3. |
| 1.3.6.1.4.1.7262.1.12.15.11 | ScalarnicFramesInQueue4 | read-only | mandatory | The current count of NIC frames passed through queue 4. |
| 1.3.6.1.4.1.7262.1.12.15.12 | ScalarnicFramesInQueue3Discarded | read-only | mandatory | The current count of NIC frames received in queue 3 that were discarded, but due to an error. One possible reason is lack of buffer space. |
| 1.3.6.1.4.1.7262.1.12.15.13 | ScalarnicFramesInQueue4Discarded | read-only | mandatory | The current count of NIC frames received in queue 4 that were discarded, but due to an error. One possible reason is lack of buffer space. |
| 1.3.6.1.4.1.7262.1.12.16 | ScalarmaxFrameSize | read-write | mandatory | The default maximum frame size is 1600 bytes. The settable maximum frame size must be a multiple of 128. If the chosen maximum frame size is not a multiple of … |
| 1.3.6.1.4.1.7262.1.12.17 | ScalarpauseFrameEnable | read-write | mandatory | When PAUSE is enabled, pause frames can be generated by the system and the pause frames will flow toward the link partner on the network. When PAUSE is enabled… |
| 1.3.6.1.4.1.7262.1.12.18 | ScalaropticalTransmitterState | read-write | mandatory | When it is on, optical transmitter is enabled. Otherwise optical transmitter is disabled. |
| 1.3.6.1.4.1.7262.1.13 | NodeapIntermediateFrequencyCard | |||
| 1.3.6.1.4.1.7262.1.13.1 | ScalarintermediateFrequencyDesc | read-only | mandatory | A textual string containing information about the modem. Includes the manufacturer, product name, software version, and hardware version of the modem card. |
| 1.3.6.1.4.1.7262.1.13.2 | ScalarifTxSynthesizerLock | read-only | mandatory | Indicates if the transmit synthesizer is locked. |
| 1.3.6.1.4.1.7262.1.13.3 | ScalarifRxSynthesizerLock | read-only | mandatory | Indicates if the receive synthesizer is locked. |
| 1.3.6.1.4.1.7262.1.14 | NodeapFrequencies | |||
| 1.3.6.1.4.1.7262.1.14.1 | ScalarfrequencyType | read-write | mandatory | The radio frequency standard used in the system. Frequency bands are divided into sub bands. ie FCC 23 Ghz Band is comprised of fcc23a, fcc23b, fcc23c and fcc2… |
| 1.3.6.1.4.1.7262.1.14.2 | ScalarfreqGroupSelected | read-write | mandatory | The frequency group selected for the system. The frequency subbands are divided into frequency groups txHigh and txLow. An AIRPAIR system must have one node co… |
| 1.3.6.1.4.1.7262.1.14.3 | TabletxHighFreqTable | not-accessible | mandatory | A table of txHigh frequency settings for the system |
| 1.3.6.1.4.1.7262.1.14.3.1 | RowtxHighFreqEntry | not-accessible | mandatory | A txHighFrequency entry containing all the frequency values |
| 1.3.6.1.4.1.7262.1.14.3.1.1 | ColumntxHighFreqIndex | read-only | mandatory | A unique value for each frequency channel. |
| 1.3.6.1.4.1.7262.1.14.3.1.2 | ColumntxHighFreqChannelIndex | read-only | mandatory | The channel index for the frequency. |
| 1.3.6.1.4.1.7262.1.14.3.1.3 | ColumntxHighFreqTransmitIfFrequency | read-only | mandatory | The IF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.3.1.4 | ColumntxHighFreqReceiveIfFrequency | read-only | mandatory | The IF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.3.1.5 | ColumntxHighFreqTransmitRfFrequency | read-only | mandatory | The RF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.3.1.6 | ColumntxHighFreqReceiveRfFrequency | read-only | mandatory | The RF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.3.1.7 | ColumntxHighFreqAvailable | read-write | mandatory | Specifies whether the frequency channel can be used. |
| 1.3.6.1.4.1.7262.1.14.3.1.8 | ColumntxHighFreqSelected | read-write | mandatory | Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system. |
| 1.3.6.1.4.1.7262.1.14.4 | TabletxLowFreqTable | not-accessible | mandatory | A table of txLow frequency settings for the system |
| 1.3.6.1.4.1.7262.1.14.4.1 | RowtxLowFreqEntry | not-accessible | mandatory | A txLowFrequeny entry containing the frequency values for a specific index |
| 1.3.6.1.4.1.7262.1.14.4.1.1 | ColumntxLowFreqIndex | read-only | mandatory | A unique value for each frequency channel. |
| 1.3.6.1.4.1.7262.1.14.4.1.2 | ColumntxLowFreqChannelIndex | read-only | mandatory | The channel index for the frequency. |
| 1.3.6.1.4.1.7262.1.14.4.1.3 | ColumntxLowFreqTransmitIfFrequency | read-only | mandatory | The IF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.4.1.4 | ColumntxLowFreqReceiveIfFrequency | read-only | mandatory | The IF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.4.1.5 | ColumntxLowFreqTransmitRfFrequency | read-only | mandatory | The RF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.4.1.6 | ColumntxLowFreqReceiveRfFrequency | read-only | mandatory | The RF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.4.1.7 | ColumntxLowFreqAvailable | read-write | mandatory | Specifies whether the frequency channel can be used. |
| 1.3.6.1.4.1.7262.1.14.4.1.8 | ColumntxLowFreqSelected | read-write | mandatory | Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system. |
| 1.3.6.1.4.1.7262.1.14.5 | TablegoFreqTable | not-accessible | mandatory | A table of go frequency settings for the system |
| 1.3.6.1.4.1.7262.1.14.5.1 | RowgoFreqEntry | not-accessible | mandatory | A goFrequency entry containing all the frequency values |
| 1.3.6.1.4.1.7262.1.14.5.1.1 | ColumngoFreqIndex | read-only | mandatory | A unique value for each frequency channel. |
| 1.3.6.1.4.1.7262.1.14.5.1.2 | ColumngoFreqChannelIndex | read-only | mandatory | The channel index for the frequency. |
| 1.3.6.1.4.1.7262.1.14.5.1.3 | ColumngoFreqTransmitIfFrequency | read-only | mandatory | The IF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.5.1.4 | ColumngoFreqReceiveIfFrequency | read-only | mandatory | The IF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.5.1.5 | ColumngoFreqTransmitRfFrequency | read-only | mandatory | The RF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.5.1.6 | ColumngoFreqReceiveRfFrequency | read-only | mandatory | The RF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.5.1.7 | ColumngoFreqAvailable | read-only | mandatory | Specifies whether the frequency channel can be used. |
| 1.3.6.1.4.1.7262.1.14.5.1.8 | ColumngoFreqSelected | read-write | mandatory | Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system. |
| 1.3.6.1.4.1.7262.1.14.6 | TablereturnFreqTable | not-accessible | mandatory | A table of return frequency settings for the system |
| 1.3.6.1.4.1.7262.1.14.6.1 | RowreturnFreqEntry | not-accessible | mandatory | A returnFrequency entry containing all the frequency values |
| 1.3.6.1.4.1.7262.1.14.6.1.1 | ColumnreturnFreqIndex | read-only | mandatory | A unique value for each frequency channel. |
| 1.3.6.1.4.1.7262.1.14.6.1.2 | ColumnreturnFreqChannelIndex | read-only | mandatory | The channel index for the frequency. |
| 1.3.6.1.4.1.7262.1.14.6.1.3 | ColumnreturnFreqTransmitIfFrequency | read-only | mandatory | The IF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.6.1.4 | ColumnreturnFreqReceiveIfFrequency | read-only | mandatory | The IF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.6.1.5 | ColumnreturnFreqTransmitRfFrequency | read-only | mandatory | The RF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.6.1.6 | ColumnreturnFreqReceiveRfFrequency | read-only | mandatory | The RF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.6.1.7 | ColumnreturnFreqAvailable | read-only | mandatory | Specifies whether the frequency channel can be used. |
| 1.3.6.1.4.1.7262.1.14.6.1.8 | ColumnreturnFreqSelected | read-write | mandatory | Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system. |
| 1.3.6.1.4.1.7262.1.14.7 | TableunlicensedTxFreqTable | not-accessible | mandatory | OBSOLETE. A table of unlicensed Tx frequency settings for the system |
| 1.3.6.1.4.1.7262.1.14.7.1 | RowunlicensedTxFreqEntry | not-accessible | mandatory | A unlicensed Tx entry containing all the frequency values |
| 1.3.6.1.4.1.7262.1.14.7.1.1 | ColumnunlicensedTxFreqIndex | read-only | mandatory | A unique value for each frequency channel. |
| 1.3.6.1.4.1.7262.1.14.7.1.2 | ColumnunlicensedTxFreqChannelIndex | read-only | mandatory | The channel index for the frequency. |
| 1.3.6.1.4.1.7262.1.14.7.1.3 | ColumnunlicensedTxIfFrequency | read-only | mandatory | The IF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.7.1.4 | ColumnunlicensedTxRfFrequency | read-only | mandatory | The RF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.7.1.5 | ColumnsetUnlicensedTxFrequency | read-write | mandatory | To set the TX frequencies in the progrmmed frequency. |
| 1.3.6.1.4.1.7262.1.14.8 | TableunlicensedRxFreqTable | not-accessible | mandatory | OBSOLETE. A table of unlicensed Rx frequency settings for the system |
| 1.3.6.1.4.1.7262.1.14.8.1 | RowunlicensedRxFreqEntry | not-accessible | mandatory | A unlicensed Rx entry containing all the frequency values |
| 1.3.6.1.4.1.7262.1.14.8.1.1 | ColumnunlicensedRxFreqIndex | read-only | mandatory | A unique value for each frequency channel. |
| 1.3.6.1.4.1.7262.1.14.8.1.2 | ColumnunlicensedRxFreqChannelIndex | read-only | mandatory | The channel index for the frequency. |
| 1.3.6.1.4.1.7262.1.14.8.1.3 | ColumnunlicensedRxIfFrequency | read-only | mandatory | The IF Rx frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.8.1.4 | ColumnunlicensedRxRfFrequency | read-only | mandatory | The RF Rx frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.8.1.5 | ColumnsetUnlicensedRxFrequency | read-write | mandatory | To set the Rx frequencies in the progrmmed frequency. |
| 1.3.6.1.4.1.7262.1.14.9 | NodeprogrammedFrequency | |||
| 1.3.6.1.4.1.7262.1.14.9.1 | ScalarprogrammedFrequencyChannel | read-only | mandatory | The channel that has been programmed into the system. |
| 1.3.6.1.4.1.7262.1.14.9.2 | ScalarprogrammedFrequencyTxIf | read-only | mandatory | The programmed IF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.9.3 | ScalarprogrammedFrequencyRxIf | read-only | mandatory | The programmed IF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.9.4 | ScalarprogrammedFrequencyTxRf | read-only | mandatory | The programmed RF TX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.9.5 | ScalarprogrammedFrequencyRxRf | read-only | mandatory | The RF RX frequency in MHz. |
| 1.3.6.1.4.1.7262.1.14.10 | NodeapFrequencyFile | |||
| 1.3.6.1.4.1.7262.1.14.10.1 | ScalarfrequencyFileOption | read-only | mandatory | Option which tells whether frequency file is being used for system settings. |
| 1.3.6.1.4.1.7262.1.15 | NodeapModem | |||
| 1.3.6.1.4.1.7262.1.15.1 | ScalarmdmDesc | read-only | mandatory | A textual string containing information about the modem. Includes the manufacturer, product name, software version, and hardware version of the modem card. |
| 1.3.6.1.4.1.7262.1.15.2 | ScalarmdmModulationType | read-only | mandatory | The modulation type of the modem, distinguished according to the physical/link protocol. |
| 1.3.6.1.4.1.7262.1.15.3 | ScalarmdmCurrentRxSpeed | read-only | mandatory | An estimate of the modem's current Rx bandwidth in bits per second. |
| 1.3.6.1.4.1.7262.1.15.4 | ScalarmdmCurrentTxSpeed | read-only | mandatory | An estimate of the modem's current Tx bandwidth in bits per second. |
| 1.3.6.1.4.1.7262.1.15.5 | ScalarmdmAdminStatus | read-write | mandatory | NOT IMPLEMENTED The desired state of the modem card. 'testing' and 'down' indicates that no user packet data can be passed. |
| 1.3.6.1.4.1.7262.1.15.6 | ScalarmdmOperStatus | read-only | mandatory | The current operational state of the interface. Testing indicates that no operational packets can be passed. |
| 1.3.6.1.4.1.7262.1.15.7 | ScalarmdmLastChange | read-only | mandatory | The value of sysUpTime at the time the modem entered its current operational state. If the current state was entered prior to the last re-initialization of the… |
| 1.3.6.1.4.1.7262.1.15.8 | ScalarmdmBer | read-only | mandatory | An estimation of the current uncorrected BER. Uncorrected BER is the bit error rate as measured before frame error correction. |
| 1.3.6.1.4.1.7262.1.15.9 | ScalarmdmEbToNoiseRatio | read-only | mandatory | The ratio of the modem Estimated Energy per information bit to Noise power spectral density |
| 1.3.6.1.4.1.7262.1.15.10 | ScalarmdmRSL | read-only | mandatory | NOT USED. DEPRECATED. Use radioRSL object in radio folder. The Received Signal Level at the demodulator. Indicates the power of the receive level in -dBm. |
| 1.3.6.1.4.1.7262.1.15.11 | ScalarmdmEqualizerStress | read-only | mandatory | Indicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working. |
| 1.3.6.1.4.1.7262.1.15.12 | ScalarmdmReset | read-write | mandatory | Writing 1 to this object causes the modem card to be reset. All other values are not recognized. This variable always reads back as 0. mdmOperStatus should be … |
| 1.3.6.1.4.1.7262.1.15.13 | ScalarmdmSlopeEqualizerStress | read-only | mandatory | A floating point number indicating how much the received signal has been spectrally sloped. |
| 1.3.6.1.4.1.7262.1.15.14 | ScalarmdmPhaseImbalance | read-only | mandatory | Reports the I/Q phase correction applied by demodulator ASSP correction loops. |
| 1.3.6.1.4.1.7262.1.15.15 | ScalarmdmAmplitudeImbalance | read-only | mandatory | Reports the I/Q amplitude correction applied by demodulator ASSP correction loops. |
| 1.3.6.1.4.1.7262.1.15.16 | NodemdmStatistics | |||
| 1.3.6.1.4.1.7262.1.15.16.1 | ScalarmdmFramesOut | read-only | mandatory | The current count of Modem frames sent. |
| 1.3.6.1.4.1.7262.1.15.16.2 | ScalarmdmFramesBlocksIn | read-only | mandatory | The current count of Modem blocks received. |
| 1.3.6.1.4.1.7262.1.15.16.3 | ScalarmdmFramesBlocksInError | read-only | mandatory | The current count of Modem blocks received in error. |
| 1.3.6.1.4.1.7262.1.15.16.4 | ScalarmdmFramesIn | read-only | mandatory | The current count of Modem frames received. |
| 1.3.6.1.4.1.7262.1.15.16.5 | ScalarmdmFramesInError | read-only | mandatory | The current count of Modem frames received in error. |
| 1.3.6.1.4.1.7262.1.15.16.6 | ScalarmdmQueueFramesDiscarded | read-only | mandatory | The current count of Modem frames in the queue that were discarded. |
| 1.3.6.1.4.1.7262.1.15.16.7 | ScalarmdmBWUtilization | read-only | mandatory | The carried load over link capacity. |
| 1.3.6.1.4.1.7262.1.15.16.8 | ScalarmdmIngressDataRate | read-only | mandatory | The data rate coming into the ethernet port. The data rate you see is multiplied by 100. e.g. A display of 1530 is actually 15.30 Mpbs |
| 1.3.6.1.4.1.7262.1.15.16.9 | ScalarmdmEgressDataRate | read-only | mandatory | The data rate going out of the ethernet port. The data rate you see is multiplied by 100. e.g. A display of 1530 is actually 15.30 Mpbs. |
| 1.3.6.1.4.1.7262.1.15.17 | ScalaraamStatus | read-write | mandatory | Indicates whether Automatic Adaptive Modulation(AAM) is enabled. |
| 1.3.6.1.4.1.7262.1.15.18 | ScalarmdmCurrentRxSpeedInt | read-only | mandatory | Integer version of 'mdmCurrentRxSpeed' object. Divide by '10000' to get the actual value. Mainly provided to facilitate plotting of values. An estimate of the … |
| 1.3.6.1.4.1.7262.1.15.19 | ScalarmdmCurrentTxSpeedInt | read-only | mandatory | Integer version of 'mdmCurrentTxSpeed' object. Divide by '10000' to get the actual value. Mainly provided to facilitate plotting of values. An estimate of the … |
| 1.3.6.1.4.1.7262.1.15.20 | ScalarmdmBerInt | read-only | mandatory | Integer version of 'mdmBer' object.Divide by 1e+8 to get the actual value. Any value less than 1e-8 will be truncated to 0.Mainly provided to facilitate plotti… |
| 1.3.6.1.4.1.7262.1.15.21 | ScalarmdmEbToNoiseRatioInt | read-only | mandatory | Integer version of 'mdmEbToNoiseRatio' object. Divide by '10' to get the actual value. Mainly provided to facilitate plotting of values. The ratio of the modem… |
| 1.3.6.1.4.1.7262.1.15.22 | ScalarmdmSlopeEqualizerStressInt | read-only | mandatory | Integer version of 'mdmSlopeEqualizerStress' object. Divide by '100' to get the actual value. Mainly provided to facilitate plotting of values.A floating point… |
| 1.3.6.1.4.1.7262.1.15.23 | ScalarmdmPhaseImbalanceInt | read-only | mandatory | Integer version of 'mdmPhaseImbalance' object. Divide by '100' to get the actual value. Mainly provided to facilitate plotting of values.Reports the I/Q phase … |
| 1.3.6.1.4.1.7262.1.15.24 | ScalarmdmAmplitudeImbalanceInt | read-only | mandatory | Integer version of 'mdmAmplitudeImbalance' object. Divide by '100' to get the actual value. Mainly provided to facilitate plotting of values. Reports the I/Q a… |
| 1.3.6.1.4.1.7262.1.16 | NodeapRadio | |||
| 1.3.6.1.4.1.7262.1.16.1 | ScalarradioDesc | read-only | mandatory | A textual string containing information about the radio. Includes the manufacturer, product name, software version, serial number, and hardware version of the … |
| 1.3.6.1.4.1.7262.1.16.2 | ScalarradioPhysAddr | read-only | mandatory | The physical address used to distinguish it from other radios. |
| 1.3.6.1.4.1.7262.1.16.3 | ScalarradioAdminStatus | read-write | mandatory | OBSOLETE. The desired state of the radio. The radio only transmits when in the up state i.e. the transmitter is muted when in the down, testing state or firmwa… |
| 1.3.6.1.4.1.7262.1.16.4 | ScalarradioOperStatus | read-only | mandatory | The current operational state of the interface. Testing indicates that no operational packets can be passed. Testing also indicates that a firmware upgrade may… |
| 1.3.6.1.4.1.7262.1.16.5 | ScalarradioLastChanged | read-only | mandatory | The value of sysUpTime at the time the radio entered its current operational state. If the current state was entered prior to the last re-initialization of the… |
| 1.3.6.1.4.1.7262.1.16.6 | ScalarradioRSL | read-only | mandatory | The Received Signal Level indicates the power of the receive level in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm. |
| 1.3.6.1.4.1.7262.1.16.7 | ScalarradioTxGain | read-write | mandatory | The gain of the radio in the transmit chain. Indicates the gain in dB. |
| 1.3.6.1.4.1.7262.1.16.8 | ScalarradioRxGain | read-write | mandatory | The gain of the radio in the receive chain. Indicates the gain in dB. |
| 1.3.6.1.4.1.7262.1.16.9 | ScalarradioVoltageSupply | read-only | mandatory | The voltage level of the supply to the radio. |
| 1.3.6.1.4.1.7262.1.16.10 | ScalarradioReset | read-write | mandatory | Writing 1 to this object causes the radio to be reset. All other values are not recognized. This variable always reads back as 0. radioOperStatus should be pol… |
| 1.3.6.1.4.1.7262.1.16.11 | ScalartransmitPowerDbm | read-write | mandatory | This defines the transmit level of the radio. If ATPC is enabled, you can't change the transmit power. The power you see is divided by 10. e.g. A display of 13… |
| 1.3.6.1.4.1.7262.1.16.12 | ScalarprogrammedAntennaDiameter | read-write | mandatory | This defines the diameter of the antenna used by the system represented in inches. |
| 1.3.6.1.4.1.7262.1.16.13 | ScalarpowerOption | read-write | mandatory | This indicates the power option of the radio: normal or high power. |
| 1.3.6.1.4.1.7262.1.16.14 | ScalaratpcStatus | read-write | mandatory | Indicates whether Automatic Transmit Power Control (ATPC) is enabled. |
| 1.3.6.1.4.1.7262.1.16.15 | ScalaratpcRslThreshold | read-only | mandatory | This defines the atpc rsl threshold. |
| 1.3.6.1.4.1.7262.1.16.16 | ScalaratpcFadeStep | read-only | mandatory | This defines atpc fade step size. |
| 1.3.6.1.4.1.7262.1.16.17 | ScalaratpcRslHysteresis | read-only | mandatory | This defines the rsl hysteresis. |
| 1.3.6.1.4.1.7262.1.16.18 | ScalaratpcMaximumChange | read-only | mandatory | This defines the maximum allowed atpc change. |
| 1.3.6.1.4.1.7262.1.16.19 | ScalarredundancyStatus | read-write | mandatory | Indicates whether radio redundancy is enabled or not. It can be turned on only when there is valid primary and secondary serial number in flash |
| 1.3.6.1.4.1.7262.1.16.20 | ScalarredundancyMode | read-write | mandatory | Radio installtion type dcdp - different channel or differenr polarzation, scsp - same channel and same polarization |
| 1.3.6.1.4.1.7262.1.16.21 | ScalarredundancyCurrentSerialNum | read-only | mandatory | Display active radio's serial number |
| 1.3.6.1.4.1.7262.1.16.22 | ScalarredundancySecondarySerialNum | read-write | mandatory | Display the secondary radio's serial number in flash |
| 1.3.6.1.4.1.7262.1.16.23 | ScalarredundancyPrimarySerialNum | read-write | mandatory | Display the primary radio's serial number in flash |
| 1.3.6.1.4.1.7262.1.16.24 | ScalarradioRSLUnsignedInt | read-only | mandatory | The Received Signal Level indicates the power of the receive level in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm. Object provided mainly … |
| 1.3.6.1.4.1.7262.1.16.25 | ScalarradioTemperature | read-only | mandatory | The Radio temperature in degree Centigrade. The actual temperature is got by dividing the number by 10. e.g. -432 is actually -43.2 degree centigrade. |
| 1.3.6.1.4.1.7262.1.17 | NodeapCalendar | |||
| 1.3.6.1.4.1.7262.1.17.1 | Scalardate | read-only | mandatory | A string in the format as follows: XX/YY/ZZ Where XX = day of month (range 01 to 31) YY = month of year(range 01 to 12) ZZ = year (range 01 - 99) |
| 1.3.6.1.4.1.7262.1.17.2 | Scalartime | read-only | mandatory | A string in the format as follows: aa:bb:cc:dd Where aa = hour of day ( range 00 to 23 ) bb = minute of hour ( range 00 to 59 ) cc = second of minute( range 00… |
| 1.3.6.1.4.1.7262.1.18 | NodeapLeds | |||
| 1.3.6.1.4.1.7262.1.18.1 | ScalarpowerLed | read-only | mandatory | Indicates the status of the power led. |
| 1.3.6.1.4.1.7262.1.18.2 | ScalarlinkStatusOrSpeedLed | read-only | mandatory | Indicates the status of Ethernet link for release 3 or earlier hardware platforms. Indicates the speed of the Ethernet link for release 4 or later platforms. T… |
| 1.3.6.1.4.1.7262.1.18.3 | ScalartrafficLed | read-only | mandatory | Indicates the presence of Ethernet traffic. It represents transmit and receive traffic on the ethernet interface. |
| 1.3.6.1.4.1.7262.1.18.4 | ScalarduplexModeOrLinkTypeLed | read-only | mandatory | For release 3 or earlier hardward platforms, indicates whether the Ethernet link is working in full duplex mode, 1 means off and 2 means on. The values of 3, 4… |
| 1.3.6.1.4.1.7262.1.18.5 | ScalarrfOnLed | read-only | mandatory | Indicates whether the radio is transmitting or not |
| 1.3.6.1.4.1.7262.1.18.6 | ScalarmodemSyncLed | read-only | mandatory | Indicates that the modem is synchronized to another AirPair |
| 1.3.6.1.4.1.7262.1.18.7 | ScalarsystemTroubleLed | read-only | mandatory | Indicates the status of the system trouble LED. The Trouble LED will be on if on of the following conditions exist: i)Communication with the radio has failed. … |
| 1.3.6.1.4.1.7262.1.18.8 | ScalarmultiSegmentLed | read-only | mandatory | NOT IMPLEMENTED Indicates the value loaded to the multi-segment LED. Used for antenna alignment. Value is read as a percentage. |
| 1.3.6.1.4.1.7262.1.18.9 | ScalarfanAlarmLed | read-only | mandatory | Indicates whether the fan alarm led is off or not.If any one of the fan stops working, this led will be turned on. This alarm is applicable for split IDU/ODU m… |
| 1.3.6.1.4.1.7262.1.19 | NodeapSystemAlarms | |||
| 1.3.6.1.4.1.7262.1.19.1 | ScalarclearAlarmCounters | write-only | mandatory | Clears the alarm counters for the specified group |
| 1.3.6.1.4.1.7262.1.19.2 | NodenetworkInterfaceCardAlarms | |||
| 1.3.6.1.4.1.7262.1.19.2.1 | ScalarexplicitAuthenticationFailure | read-only | mandatory | Authentication of the peer AirPair node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on AirPair faulty… |
| 1.3.6.1.4.1.7262.1.19.2.2 | ScalarexplicitAuthenticationFailureCount | read-only | mandatory | Indicates the number of times explicit authentication has failed. |
| 1.3.6.1.4.1.7262.1.19.2.3 | ScalarautoNegotiationDuplexMismatch | read-only | mandatory | NOT USED. DEPRECATED. The AirPair ethernet interface has a mismatch in duplex. The severity is major, the probable cause is an incorrect configuration of the s… |
| 1.3.6.1.4.1.7262.1.19.2.4 | ScalarautoNegotiationDuplexMismatchCount | read-only | mandatory | NOT USED. DEPRECATED. Indicates the number of times auto negotiation has failed. |
| 1.3.6.1.4.1.7262.1.19.2.5 | ScalardroppedEnetFramesThresholdExceeded | read-only | mandatory | The threshold for number of frames dropped has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the … |
| 1.3.6.1.4.1.7262.1.19.2.6 | ScalardroppedEnetFramesThresholdParameters | read-write | mandatory | A read-write string: The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the form… |
| 1.3.6.1.4.1.7262.1.19.2.7 | ScalardroppedEnetFramesThresholdCount | read-only | mandatory | Indicates the approximate time, in seconds, that this alarm has been in the active state |
| 1.3.6.1.4.1.7262.1.19.2.8 | ScalarbandwidthUtilizationThresholdExceeded | read-only | mandatory | The threshold for the percentage of available bandwidth has been exceeded. The threshold and the number of seconds that it must exceed this threshold are progr… |
| 1.3.6.1.4.1.7262.1.19.2.9 | ScalarbandwidthUtilizationThresholdParameters | read-write | mandatory | A read-write string: The percentage of available bandwidth threshold and the number of seconds that it must exceed this threshold are programmed by the user. A… |
| 1.3.6.1.4.1.7262.1.19.2.10 | ScalarbandwidthUtilizationThresholdCount | read-only | mandatory | Indicates the approximate time, in seconds, that this alarm has been in the active state |
| 1.3.6.1.4.1.7262.1.19.2.11 | ScalarrlsMismatch | read-only | mandatory | RLS configurations on the pair of systems are mismatched. |
| 1.3.6.1.4.1.7262.1.19.2.12 | ScalarrlsMismatchCount | read-only | mandatory | Indicates the approximate time, in seconds, that this alarm has been in the active state |
| 1.3.6.1.4.1.7262.1.19.2.13 | ScalarrLSShutdownActivated | read-only | mandatory | RLS shutdown is activated. |
| 1.3.6.1.4.1.7262.1.19.2.14 | ScalarrLSShutdownActivatedCount | read-only | mandatory | Indicates the approximate time, in seconds, that this alarm has been in the active state |
| 1.3.6.1.4.1.7262.1.19.2.15 | ScalarethernetLinkDown | read-only | mandatory | Indicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected t… |
| 1.3.6.1.4.1.7262.1.19.2.16 | ScalarethernetLinkDownActivatedCount | read-only | mandatory | Indicates the approximate time, in seconds, that this alarm has been in the active state |
| 1.3.6.1.4.1.7262.1.19.3 | NodemodemAlarms | |||
| 1.3.6.1.4.1.7262.1.19.3.1 | ScalarmodemLossOfSignalLockFromDemodulator | read-only | mandatory | Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of acti… |
| 1.3.6.1.4.1.7262.1.19.3.2 | ScalarmodemLossOfSignalLockFromDemodulatorCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.3 | ScalarmodemUncorrectedBerThresholdExceeded | read-only | mandatory | The uncorrected BER threshold has been exceeded. The severity is major, the probable cause is physical interference in the air link or misalignment of the radi… |
| 1.3.6.1.4.1.7262.1.19.3.4 | ScalarmodemUncorrectedBerThresholdParameters | read-write | mandatory | A read-write string: The threshold, in exponential format, and the number of seconds in exponential format that the uncorrected BER must exceed this threshold … |
| 1.3.6.1.4.1.7262.1.19.3.5 | ScalarmodemUncorrectedBerThresholdExceededCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.6 | ScalarmodemModulatorPllLockFailure | read-only | mandatory | Modulator PLL failure. The severity is critical, the probable cause a faulty modem card within AirPair, and recommended course of action is to replace the mode… |
| 1.3.6.1.4.1.7262.1.19.3.7 | ScalarmodemModulatorPllLockFailureCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.8 | ScalarmodemModulatorLossOfSyncBytes | read-only | mandatory | Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course… |
| 1.3.6.1.4.1.7262.1.19.3.9 | ScalarmodemModulatorLossOfSyncBytesCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.10 | ScalarmodemModulatorInputFifoError | read-only | mandatory | Overrun or underrun of the FIFO contained inside the modulator. The severity is critical, the probable cause is electrical interference, and recommended course… |
| 1.3.6.1.4.1.7262.1.19.3.11 | ScalarmodemModulatorInputFifoErrorCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.12 | ScalarmodemModulatorInputDataError | read-only | mandatory | All ones or all zeroes at the input of the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action… |
| 1.3.6.1.4.1.7262.1.19.3.13 | ScalarmodemModulatorInputDataErrorCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.14 | ScalarmodemSnrBelowThreshold | read-only | mandatory | The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misali… |
| 1.3.6.1.4.1.7262.1.19.3.15 | ScalarmodemSnrAlarmThresholdParameter | read-write | mandatory | The demodulator SNR threshold level which triggers the modemSnrBelowThreshold alarm. A number in the range 10 to 25. The proper setting depends on the operatio… |
| 1.3.6.1.4.1.7262.1.19.3.16 | ScalarmodemSnrBelowThresholdCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.17 | ScalarmodemCardMismatchedHardwareFirmware | read-only | mandatory | The modem card has firmware that is incompatible with the hardware. The card will not operate properly. |
| 1.3.6.1.4.1.7262.1.19.3.18 | ScalarmodemCardMismatchedHardwareFirmwareCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.19 | ScalarmodemAAMConfigMismatch | read-only | mandatory | In the near end Automatic Adaptive Modulation(AAM) feature set to on and in peer it is set to off |
| 1.3.6.1.4.1.7262.1.19.3.20 | ScalarmodemAAMConfigMismatchCount | read-only | mandatory | Indicates the approximate number of seconds AAMConfigMismatch alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.3.21 | ScalarmodemAAMQpskActive | read-only | mandatory | Indicates aam is active and system running on QPSK modulation |
| 1.3.6.1.4.1.7262.1.19.3.22 | ScalarmodemAAMQpskActiveCount | read-only | mandatory | Indicates the approximate number of seconds AAMQpskActive alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4 | NoderadioAlarms | |||
| 1.3.6.1.4.1.7262.1.19.4.1 | ScalarradioPLDROLostLock | read-only | mandatory | The PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is t… |
| 1.3.6.1.4.1.7262.1.19.4.2 | ScalarradioPLDROLostLockCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4.3 | ScalarradioLostCommunication | read-only | mandatory | RS232 communication lost between AIRPAIR and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recomme… |
| 1.3.6.1.4.1.7262.1.19.4.4 | ScalarradioLostCommunicationCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4.5 | ScalarradioMismatch | read-only | mandatory | The radio connected to the AIRPAIR modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrect… |
| 1.3.6.1.4.1.7262.1.19.4.6 | ScalarradioMismatchCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4.7 | ScalarradioPowerAmp | read-only | mandatory | The power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit with… |
| 1.3.6.1.4.1.7262.1.19.4.8 | ScalarradioPowerAmpCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4.9 | ScalarradioRslBelowThreshold | read-only | mandatory | The minimum radio receive signal level threshold has been crossed. The severity is major, the probable cause is physical interference in the air link path or m… |
| 1.3.6.1.4.1.7262.1.19.4.10 | ScalarradioRslBelowThresholdParameters | read-write | mandatory | A read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows:… |
| 1.3.6.1.4.1.7262.1.19.4.11 | ScalarradioRslBelowThresholdCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4.12 | ScalarradioHighPowerOptionM1 | read-only | mandatory | This applies to High Power Radios only. Indicates Power Amp Alarm (M1). |
| 1.3.6.1.4.1.7262.1.19.4.13 | ScalarradioHighPowerOptionM1Count | read-only | mandatory | This applies to High Power Radios only. Indicates the number of seconds that Power Amp Alarm (M1) has been active. |
| 1.3.6.1.4.1.7262.1.19.4.14 | ScalarradioHighPowerOptionM2 | read-only | mandatory | This applies to High Power Radios only. Indicates Power Amp Alarm (M2). |
| 1.3.6.1.4.1.7262.1.19.4.15 | ScalarradioHighPowerOptionM2Count | read-only | mandatory | This applies to High Power Radios only. Indicates the number of seconds that Power Amp Alarm (M2) has been active. |
| 1.3.6.1.4.1.7262.1.19.4.16 | ScalarradioHighPowerTxDetector | read-only | mandatory | This applies to High Power Radios only. Indicates minimum power threshold has not been surpassed. |
| 1.3.6.1.4.1.7262.1.19.4.17 | ScalarradioHighPowerTxDetectorCount | read-only | mandatory | This applies to High Power Radios only. Indicates the number of seconds that radioHighPowerTxDetector alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.4.18 | ScalaratpcConfigMismatch | read-only | mandatory | The pair of the systems don't have same ATPC configurations. On one side ATPC is enabled, but on the other side ATPC is not enabled. |
| 1.3.6.1.4.1.7262.1.19.4.19 | ScalaratpcConfigMismatchCount | read-only | mandatory | Indicates how long atpc configurations are mismatched on the two systems. |
| 1.3.6.1.4.1.7262.1.19.4.20 | ScalarredundancySecondaryActive | read-only | mandatory | Radio redundancy on, secondary radio is active |
| 1.3.6.1.4.1.7262.1.19.4.21 | ScalarredundancySecondaryActiveCount | read-only | mandatory | Indicates how long secondary radio is active. |
| 1.3.6.1.4.1.7262.1.19.4.22 | ScalarredundancySerialNumMismatch | read-only | mandatory | Radio serial number programmed in flash and radio doesn't match |
| 1.3.6.1.4.1.7262.1.19.4.23 | ScalarredundancySerialNumMismatchCount | read-only | mandatory | Indicates how long redundancyserailNumMismatch alarm is active. |
| 1.3.6.1.4.1.7262.1.19.4.24 | ScalarexcessiveCableLossChange | read-only | mandatory | Cable loss change exceeds the threshold |
| 1.3.6.1.4.1.7262.1.19.4.25 | ScalarexcessiveCableLossChangeCount | read-only | mandatory | Indicates how long Cable loss change has exceeded the threshold |
| 1.3.6.1.4.1.7262.1.19.4.26 | ScalarexcessiveRxCableLoss | read-only | mandatory | Rx gain can not be adjusted to desired value |
| 1.3.6.1.4.1.7262.1.19.4.27 | ScalarexcessiveRxCableLossCount | read-only | mandatory | Indicates how long rx gain can not be adjusted to desired value |
| 1.3.6.1.4.1.7262.1.19.5 | NodeintermediateFrequencyCardAlarms | |||
| 1.3.6.1.4.1.7262.1.19.5.1 | ScalarifTxSynthesizerUnlocked | read-only | mandatory | The IF card within the modem unit has a Transmit Synthesizer which is not locked and as a result will not transmit. The severity is critical, the probable caus… |
| 1.3.6.1.4.1.7262.1.19.5.2 | ScalarifTxSynthesizerUnlockedCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.5.3 | ScalarifRxSynthesizerUnlocked | read-only | mandatory | The IF card within the modem unit has a Receive Synthesizer which is not locked. The severity is critical, the probable cause an incorrectly programmed frequen… |
| 1.3.6.1.4.1.7262.1.19.5.4 | ScalarifRxSynthesizerUnlockedCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. |
| 1.3.6.1.4.1.7262.1.19.6 | NodeotherAlarms | |||
| 1.3.6.1.4.1.7262.1.19.6.1 | ScalarrxCableLossExcessive | read-only | mandatory | The Rx cable loss exceeds limit. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.2 | ScalarrxCableLossExcessiveCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.3 | ScalartxCableLossExcessive | read-only | mandatory | The Tx cable loss exceeds limit. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.4 | ScalartxCableLossExcessiveCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.5 | Scalarfan1Failed | read-only | mandatory | The fan 1 failed. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.6 | Scalarfan1FailedCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.7 | Scalarfan2Failed | read-only | mandatory | The fan 2 failed. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.8 | Scalarfan2FailedCount | read-only | mandatory | Indicates the approximate number of seconds that this alarm has been active. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.19.6.9 | Scalarreserved | read-only | mandatory | To be filled. |
| 1.3.6.1.4.1.7262.1.19.6.10 | ScalarreservedAlarmCount | read-only | mandatory | To be filled. |
| 1.3.6.1.4.1.7262.1.19.6.11 | ScalarsntpServerUnavailableAlarm | read-only | mandatory | All of the SNTP servers are not available. |
| 1.3.6.1.4.1.7262.1.19.6.12 | ScalarsntpServerUnavailableAlarmCount | read-only | mandatory | Indicates how long in seconds all of the SNTP servers are not available. |
| 1.3.6.1.4.1.7262.1.19.7 | NodefrequencyFileAlarms | |||
| 1.3.6.1.4.1.7262.1.19.7.1 | ScalarfrequencyFileInvalid | read-only | mandatory | Executing frequency file is valid or not |
| 1.3.6.1.4.1.7262.1.19.7.2 | ScalarfrequencyFileInvalidCount | read-only | mandatory | Indicates the time (in secs) since this alarm exist. |
| 1.3.6.1.4.1.7262.1.19.7.3 | ScalaroptionalParaNotEntered | read-only | mandatory | Executing frequency file doesn't contain all the parameters needed for optimum performance of the system. |
| 1.3.6.1.4.1.7262.1.19.7.4 | ScalaroptionalParaNotEnteredCount | read-only | mandatory | Indicates the time (in secs) since this alarm exist. |
| 1.3.6.1.4.1.7262.1.19.7.5 | ScalarprogRadioBandNotFound | read-only | mandatory | Executing frequency file doesn't contain radio band info that is programmed in the system. |
| 1.3.6.1.4.1.7262.1.19.7.6 | ScalarprogRadioBandNotFoundCount | read-only | mandatory | Indicates the time (in secs) since this alarm exist. |
| 1.3.6.1.4.1.7262.1.20 | NodeapSnmpTraps | |||
| 1.3.6.1.4.1.7262.1.20.1 | TablesnmpTrapHostTable | not-accessible | mandatory | Table containing SNMP trap host entries. |
| 1.3.6.1.4.1.7262.1.20.1.1 | RowsnmpTrapHostEntry | not-accessible | mandatory | The snmp trap host entry containing all the trap host information |
| 1.3.6.1.4.1.7262.1.20.1.1.1 | ColumnsnmpTrapHostIndex | read-only | mandatory | A unique value for each trap host. |
| 1.3.6.1.4.1.7262.1.20.1.1.2 | ColumnsnmpTrapHostMode | read-only | mandatory | Indicates how the snmp trap host is obtained for the system. |
| 1.3.6.1.4.1.7262.1.20.1.1.3 | ColumnsnmpTrapHostIpAddress | read-only | mandatory | Indicates snmp trap host IP address. |
| 1.3.6.1.4.1.7262.1.20.1.1.4 | ColumnsnmpTrapHostDomainName | read-only | mandatory | NOT IMPLEMENTED. Indicates snmp trap host name that is used when DNS is used. |
| 1.3.6.1.4.1.7262.1.20.1.1.5 | ColumnsnmpTrapHostCommunityName | read-only | mandatory | The community string name used in Traps. |
| 1.3.6.1.4.1.7262.1.20.1.1.6 | ColumnsnmpTrapHostActivated | read-only | mandatory | Specifies whether traps are to be sent to this specific host or not |
| 1.3.6.1.4.1.7262.1.20.2 | ScalarcoldStartTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.3 | NodeexplicitAuthenticationFailureV1Trap | Authentication of the peer AirPair node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on AirPair faulty… | ||
| 1.3.6.1.4.1.7262.1.20.3 | ScalarlinkDownTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.4 | NodeautoNegotiationDuplexMismatchV1Trap | The AirPair ethernet interface has a mismatch in duplex. The severity is major, the probable cause is an incorrect configuration of the switch or router connec… | ||
| 1.3.6.1.4.1.7262.1.20.4 | ScalarlinkUpTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.5 | ScalarexplicitAuthenticationFailureTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.5 | NodemodemLossOfSignalLockFromDemodulatorV1Trap | Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of acti… | ||
| 1.3.6.1.4.1.7262.1.20.6 | ScalarautoNegotiationDuplexMismatchTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.6 | NodemodemUncorrectedBerThresholdExceededV1Trap | The uncorrected BER threshold has been exceeded. The severity is major, the probable cause is physical interference in the air link or misalignment of the radi… | ||
| 1.3.6.1.4.1.7262.1.20.7 | ScalarmodemLossOfSignalLockFromDemodulatorTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.7 | NodemodemModulatorPllLockFailureV1Trap | Modulator PLL failure. The severity is critical, the probable cause a faulty modem card within AirPair, and recommended course of action is to replace the mode… | ||
| 1.3.6.1.4.1.7262.1.20.8 | NodemodemModulatorLossOfSyncBytesV1Trap | Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course… | ||
| 1.3.6.1.4.1.7262.1.20.8 | ScalarmodemUncorrectedBerThresholdExceededTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.9 | NodemodemModulatorInputFifoErrorV1Trap | Overrun or underrun of the FIFO contained inside the modulator. The severity is critical, the probable cause is electrical interference, and recommended course… | ||
| 1.3.6.1.4.1.7262.1.20.9 | ScalarmodemModulatorPllLockFailureTrap | read-write | mandatory | Description |
| 1.3.6.1.4.1.7262.1.20.10 | NodemodemModulatorInputDataErrorV1Trap | All ones or all zeroes at the input of the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action… | ||
| 1.3.6.1.4.1.7262.1.20.10 | ScalarmodemModulatorLossOfSyncBytesTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.11 | ScalarmodemModulatorInputFifoErrorTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.11 | NodemodemSnrBelowThresholdV1Trap | The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misali… | ||
| 1.3.6.1.4.1.7262.1.20.12 | ScalarmodemModulatorInputDataErrorTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.12 | NoderadioPLDROLostLockV1Trap | The PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is t… | ||
| 1.3.6.1.4.1.7262.1.20.13 | ScalarmodemSnrBelowThresholdTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.13 | NoderadioLostCommunicationV1Trap | RS232 communication lost between AIRPAIR and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recomme… | ||
| 1.3.6.1.4.1.7262.1.20.14 | NoderadioMismatchV1Trap | The radio connected to the AIRPAIR modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrect… | ||
| 1.3.6.1.4.1.7262.1.20.14 | ScalarradioPLDROLostLockTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.15 | ScalarradioLostCommunicationTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.15 | NoderadioPowerAmpV1Trap | The power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit with… | ||
| 1.3.6.1.4.1.7262.1.20.16 | NodeifTxSynthUnlockedV1Trap | The IF card within the modem unit has a Transmit Synthesizer which is not locked and as a result will not transmit. The severity is critical, the probable caus… | ||
| 1.3.6.1.4.1.7262.1.20.16 | ScalarradioMismatchTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.17 | NodeifRxSynthUnlockedV1Trap | The IF card within the modem unit has a Receive Synthesizer which is not locked. The severity is critical, the probable cause an incorrectly programmed frequen… | ||
| 1.3.6.1.4.1.7262.1.20.17 | ScalarradioPowerAmpTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.18 | ScalarifTxSynthesizerUnlockedTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.18 | NodettySessionCommencedV1Trap | A person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. | ||
| 1.3.6.1.4.1.7262.1.20.19 | ScalarifRxSynthesizerUnlockedTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.19 | NodettySessionTerminatedV1Trap | A person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. | ||
| 1.3.6.1.4.1.7262.1.20.20 | NoderslBelowThresholdV1Trap | The RSL has been detected below its minimum threshold. | ||
| 1.3.6.1.4.1.7262.1.20.20 | ScalarttyManagementSessionCommencedTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.21 | NodedroppedFramesThresholdExceededV1Trap | The ethernet dropped frames threshold has been detected above its threshold value. | ||
| 1.3.6.1.4.1.7262.1.20.21 | ScalarttyManagementSessionTerminatedTrap | read-write | mandatory | Specifies whether this trap is to be sent or not |
| 1.3.6.1.4.1.7262.1.20.22 | NodebwUtilizationThresholdExceededV1Trap | The ethernet bandwidth threshold has been detected above its threshold value. | ||
| 1.3.6.1.4.1.7262.1.20.22 | ScalarrslThresholdExceedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the radio receive signal level threshold is exceeded. If enabled, the system will send t… |
| 1.3.6.1.4.1.7262.1.20.23 | ScalardroppedFramesThresholdExceedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the dropped ethernet frames threshold is exceeded. If enabled, the system will send this… |
| 1.3.6.1.4.1.7262.1.20.23 | NodeexplicitAuthFailureClearedV1Trap | The condition has cleared. The peer node is now authenticated. | ||
| 1.3.6.1.4.1.7262.1.20.24 | NodeautoNegDuplexMismatchClearedV1Trap | The condition has cleared. The Ethernet connection is not experiencing auto-negotiation duplex mismatch. | ||
| 1.3.6.1.4.1.7262.1.20.24 | ScalarbandwidthUtilizationThresholdExceedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will se… |
| 1.3.6.1.4.1.7262.1.20.25 | ScalarifRxCableLossExceedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will se… |
| 1.3.6.1.4.1.7262.1.20.25 | NodelossOfSyncSigFromDemoClearedV1Trap | The condition has cleared. The demodulator is synchronized. | ||
| 1.3.6.1.4.1.7262.1.20.26 | ScalarifTxCableLossExceedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will se… |
| 1.3.6.1.4.1.7262.1.20.26 | NodeuncorrectedBerThresExceededClearedV1Trap | The condition has cleared. The demodulator uncorrected BER is now below its minimum threshold value. | ||
| 1.3.6.1.4.1.7262.1.20.27 | Scalarfan1FailedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will se… |
| 1.3.6.1.4.1.7262.1.20.27 | NodemodemModPLLFailureClearedV1Trap | The condition has cleared. The modem PLL is not failing. | ||
| 1.3.6.1.4.1.7262.1.20.28 | Scalarfan2FailedTrap | read-write | mandatory | Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will se… |
| 1.3.6.1.4.1.7262.1.20.28 | NodemodemModLossOfSyncBytesClearedV1Trap | The condition has cleared. The modem is not experiencing loss of synch bytes. | ||
| 1.3.6.1.4.1.7262.1.20.29 | ScalarmdmCardHardwareFirmwareMismatchTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.29 | NodemodemModInputFifoOverUnderClearedV1Trap | The condition has cleared. The modem is not experiencing input FIFO over/under runs. | ||
| 1.3.6.1.4.1.7262.1.20.30 | ScalaratpcConfigMismatchTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.30 | NodemodemModInputDataInacClearedV1Trap | The condition has cleared. The modem is not experiencing data inactivity. | ||
| 1.3.6.1.4.1.7262.1.20.31 | ScalarhiPowerOptionM1Trap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.31 | NodesnrBelowThresholdClearedV1Trap | The condition has cleared. SNR is now above its minimum threshold value. | ||
| 1.3.6.1.4.1.7262.1.20.32 | ScalarhiPowerOptionM2Trap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.32 | NoderadioPLDROLostLockClearedV1Trap | The condition has cleared. The radio PLDRO/LO lost lock condition has cleared. | ||
| 1.3.6.1.4.1.7262.1.20.33 | ScalarhiPowerTxDetectorTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.33 | NoderadioLostCommunicationClearedV1Trap | The condition has cleared. RS232 communication has been re-establisted between AIRPAIR and the radio. | ||
| 1.3.6.1.4.1.7262.1.20.34 | NoderadioMismatchClearedV1Trap | The condtion has cleared. The radio matches the programmed parameters in the modem. | ||
| 1.3.6.1.4.1.7262.1.20.34 | ScalarsntpServersUnreachableTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.35 | NoderadioPowerAmpClearedV1Trap | The condtion has cleared. The radio Power Amp is not in the failed state. | ||
| 1.3.6.1.4.1.7262.1.20.35 | ScalarrlsMismatchTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.36 | NodeifTxSynthUnlockedClearedV1Trap | The condtion has cleared. The IF stage transmit synthesizer is now locked. | ||
| 1.3.6.1.4.1.7262.1.20.36 | ScalarrLSShutdownActivatedTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.37 | ScalarfrequencyFileInvalidTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.37 | NodeifRxSynthUnlockedClearedV1Trap | The condtion has cleared. The IF stage receive synthesizer is now locked. | ||
| 1.3.6.1.4.1.7262.1.20.38 | ScalaroptionalParaNotEntTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.38 | NoderslBelowThresholdClearedV1Trap | The condition has cleared. RSL is now above its minimum threshold. | ||
| 1.3.6.1.4.1.7262.1.20.39 | NodedroppedFramesThresholdExceededClearedV1Trap | The condition has cleared.The ethernet dropped frames threshold is now below its threshold value. | ||
| 1.3.6.1.4.1.7262.1.20.39 | ScalarprogRadioBandNotFoundTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.40 | NodebwUtilizationThresholdExceededClearedV1Trap | The condition has cleared. The ethernet bandwidth threshold is now below its threshold value. | ||
| 1.3.6.1.4.1.7262.1.20.40 | ScalarradioRedundancySwitchOverSuccessTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.41 | ScalarradioRedundancySwitchOverFailedTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.41 | NoderxIfCableLossExceededV1Trap | The Rx cable loss has exceeded limit. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.42 | ScalarradioRedundancyNoAtpcSupportTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.42 | NoderxIfCableLossExceededClearedV1Trap | The condition has cleared. The Rx cable loss is now within limit. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.43 | ScalarradioRedundancyInvalidRadioFirmwareTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.43 | NodetxIfCableLossExceededV1Trap | The Tx cable loss has exceeded limit. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.44 | ScalarradioRedundancySwitchByLocalEndTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.44 | NodetxIfCableLossExceededClearedV1Trap | The condition has cleared. The Tx cable loss is now within limit. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.45 | Nodefan1FailedV1Trap | The Fan1 has failed. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.45 | ScalarradioRedundancySwitchByPeerTrap | read-write | mandatory | Enables or disables the trap. |
| 1.3.6.1.4.1.7262.1.20.46 | ScalaraamConfigMismatchTrap | read-write | mandatory | Enables or disables the aamConfigMismatch trap. |
| 1.3.6.1.4.1.7262.1.20.46 | Nodefan1FailedClearedV1Trap | The condition has cleared. The fan1 is running normally. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.47 | ScalaraamQpskActiveTrap | read-write | mandatory | Enables or disables the aamQpskActive trap. |
| 1.3.6.1.4.1.7262.1.20.47 | Nodefan2FailedV1Trap | The Fan2 has failed. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.48 | Nodefan2FailedClearedV1Trap | The condition has cleared. The fan2 is running normally. This trap is only valid when the AirPair installation type is IDU-ODU split | ||
| 1.3.6.1.4.1.7262.1.20.48 | ScalarprimaryRadioFaultyTrap | read-write | mandatory | Enables or disables the primaryRadioFaulty trap. |
| 1.3.6.1.4.1.7262.1.20.49 | NodemodemCardMismatchedHardwareFirmwareV1Trap | The modem card has firmware that is incompatible with the hardware. The card will not operate properly. | ||
| 1.3.6.1.4.1.7262.1.20.49 | ScalarradioSerialNumberMismatchTrap | read-write | mandatory | Enables or disables the radioSerialNumberMismatch trap. |
| 1.3.6.1.4.1.7262.1.20.50 | NodemodemCardMismatchedHardwareFirmwareClearedV1Trap | The condition has cleared. The modem card does not have incompatible firmware with the hardware. | ||
| 1.3.6.1.4.1.7262.1.20.50 | TablesnmpV3TrapHostsTable | not-accessible | mandatory | Table containing snmp V3 trap host entries |
| 1.3.6.1.4.1.7262.1.20.50.1 | RowsnmpV3TrapHostsEntry | not-accessible | mandatory | Contains the snmp v3 trap host information |
| 1.3.6.1.4.1.7262.1.20.50.1.1 | ColumnsnmpV3TrapHostsIndex | read-only | mandatory | A unique value for each v3 trap host. |
| 1.3.6.1.4.1.7262.1.20.50.1.2 | ColumnsnmpV3TrapHostIpAddress | read-only | mandatory | Indicates snmp trap host IP address. |
| 1.3.6.1.4.1.7262.1.20.50.1.3 | ColumnsnmpV3TrapHostUserName | read-only | mandatory | The user name of the v3 trap host. |
| 1.3.6.1.4.1.7262.1.20.50.1.4 | ColumnsnmpV3TrapHostAuthProtocol | read-only | mandatory | The authentication alogorithm used by the v3 trap host. |
| 1.3.6.1.4.1.7262.1.20.50.1.5 | ColumnsnmpV3TrapHostAuthPassword | read-only | mandatory | The authentication password of the v3 trap host. |
| 1.3.6.1.4.1.7262.1.20.50.1.6 | ColumnsnmpV3TrapHostPrivProtocol | read-only | mandatory | The privacy encryiption alogorithm used by the v3 trap host. |
| 1.3.6.1.4.1.7262.1.20.50.1.7 | ColumnsnmpV3TrapHostPrivPassword | read-only | mandatory | The privacy password of the v3 trap host. |
| 1.3.6.1.4.1.7262.1.20.50.1.8 | ColumnsnmpV3TrapHostActivated | read-only | mandatory | Specifies whether a specific v3 trap host is allowed to access the system |
| 1.3.6.1.4.1.7262.1.20.51 | NodeatpcConfigMismatchV1Trap | ATPC configuration mismatch in the Airpair systems. ATPC is enabled at one system, but ATPC is not enabled at the other system. | ||
| 1.3.6.1.4.1.7262.1.20.51 | ScalarexcessiveCblLossChangeTrap | read-write | mandatory | Enables or disables the excessiveCblLossChange trap. |
| 1.3.6.1.4.1.7262.1.20.52 | NodeatpcConfigMismatchClearedV1Trap | ATPC configuration mismatch in the Airpair systems is cleared. Both systems enabled ATPC. | ||
| 1.3.6.1.4.1.7262.1.20.53 | NoderadioHiPwrOptM1V1Trap | When hi-power radio is used, hi-power gate M1 drain current is out of lower or upper limits. | ||
| 1.3.6.1.4.1.7262.1.20.54 | NoderadioHiPwrOptM1ClearedV1Trap | When hi-power radio is used, hi-power gate M1 drain current is between lower and upper limits. | ||
| 1.3.6.1.4.1.7262.1.20.55 | NoderadioHiPwrOptM2V1Trap | When hi-power radio is used, hi-power gate M2 drain current is out of lower or upper limits. | ||
| 1.3.6.1.4.1.7262.1.20.56 | NoderadioHiPwrOptM2ClearedV1Trap | When hi-power radio is used, hi-power gate M2 drain current is between lower and upper limits. | ||
| 1.3.6.1.4.1.7262.1.20.57 | NoderadioHiPwrTxDetectorV1Trap | When hi-power radio is used, hi-power tx detector dBm value is smaller than limit. | ||
| 1.3.6.1.4.1.7262.1.20.58 | NoderadioHiPwrTxDetectorClearedV1Trap | When hi-power radio is used, hi-power tx detector dBm value is not smaller than limit. | ||
| 1.3.6.1.4.1.7262.1.20.59 | NodesntpServersUnreachableV1Trap | Can't reach any of the sntp servers | ||
| 1.3.6.1.4.1.7262.1.20.60 | NodesntpServersUnreachableClearedV1Trap | At least one of SNTP servers is reachable | ||
| 1.3.6.1.4.1.7262.1.20.61 | NoderlsMismatchV1Trap | RLS mismatch | ||
| 1.3.6.1.4.1.7262.1.20.62 | NoderlsMismatchClearedV1Trap | RLS mismatch cleared | ||
| 1.3.6.1.4.1.7262.1.20.63 | NoderLSShutdownActivatedv1Trap | RLS shutdown is activated | ||
| 1.3.6.1.4.1.7262.1.20.64 | NoderLSShutdownActivatedClearedV1Trap | RLS shutdown is not activated | ||
| 1.3.6.1.4.1.7262.1.20.65 | NodefrequencyFileInvalidV1Trap | When the executing frequency file is invalid, this trap is generated. | ||
| 1.3.6.1.4.1.7262.1.20.66 | NodeoptionalParaNotEntFreqFileV1Trap | when the optional parameters are not entered in frequency file, and the system boots up, this trap is generated. | ||
| 1.3.6.1.4.1.7262.1.20.67 | NodeprogRadioBandNotFoundFreqFileV1Trap | when the executing frequency file doesn't contain the info related to programmed radio band, this trap is generated. | ||
| 1.3.6.1.4.1.7262.1.20.68 | NoderedundancySwitchOverSuccessTrap | Redundancy radio switch over success | ||
| 1.3.6.1.4.1.7262.1.20.69 | NoderedundancySwitchOverFailedTrap | Redundancy radio switch over failed | ||
| 1.3.6.1.4.1.7262.1.20.70 | NoderadioNoAtpcSupportTrap | Radio does not support atpc | ||
| 1.3.6.1.4.1.7262.1.20.71 | NoderadioNoAtpcSupportClearedTrap | Radio does not support atpc cleared | ||
| 1.3.6.1.4.1.7262.1.20.72 | NoderadioFirmwareMismatchTrap | Radio firmware on radio and on modem card mismatch | ||
| 1.3.6.1.4.1.7262.1.20.73 | NoderadioFirmwareMismatchClearedTrap | Radio firmware mismatch cleared | ||
| 1.3.6.1.4.1.7262.1.20.74 | NoderedundancySwitchInitByLocalend | Radio switch initiated by local end | ||
| 1.3.6.1.4.1.7262.1.20.75 | NoderedundancySwitchInitByPeer | Radio switch initiated by peer | ||
| 1.3.6.1.4.1.7262.1.20.76 | NodeaamConfigMisMatch | Adaptive modulation configuration mismatch | ||
| 1.3.6.1.4.1.7262.1.20.77 | NodeaamConfigMisMatchClear | Adaptive modulation configuration mismatch cleared | ||
| 1.3.6.1.4.1.7262.1.20.78 | NodeaamQpskActive | Adaptive modulation on and system running on QPSK modulation | ||
| 1.3.6.1.4.1.7262.1.20.79 | NodeaamQpskActiveCleared | Adaptive modulation on system running on higher modulation | ||
| 1.3.6.1.4.1.7262.1.20.81 | NodeprimaryRadioFaultyClearedTrap | primary radio is not faulty anymore | ||
| 1.3.6.1.4.1.7262.1.20.83 | NoderadioSerialNumberMismatchTrapClearedTrap | Redundancy, Radio Serial number mismatch cleared. | ||
| 1.3.6.1.4.1.7262.1.20.84 | NodeexcessiveCableLossChangeTrap | Excessive transmit cable loss change. | ||
| 1.3.6.1.4.1.7262.1.20.85 | NodeexcessiveCableLossChangeClearedTrap | Excessive transmit cable loss change cleared. | ||
| 1.3.6.1.4.1.7262.1.21 | NodeapSnmpManagers | |||
| 1.3.6.1.4.1.7262.1.21.1 | ScalarsnmpUserAccess | read-only | mandatory | Specifies the user access to the system.If access is set to managers then only managers with there ip addresses set in snmpManagersTable will be able to gain s… |
| 1.3.6.1.4.1.7262.1.21.2 | ScalarsnmpManagerAnyCommunityName | read-only | mandatory | The community string name used by the 'any' manager. |
| 1.3.6.1.4.1.7262.1.21.3 | TablesnmpManagersTable | not-accessible | mandatory | Table containing snmp manager entries |
| 1.3.6.1.4.1.7262.1.21.3.1 | RowsnmpManagersEntry | not-accessible | mandatory | Contains the snmp manager information |
| 1.3.6.1.4.1.7262.1.21.3.1.1 | ColumnsnmpManagersIndex | read-only | mandatory | A unique value for each manager. |
| 1.3.6.1.4.1.7262.1.21.3.1.2 | ColumnsnmpManagerIpAddress | read-only | mandatory | The IP address of the Manager. |
| 1.3.6.1.4.1.7262.1.21.3.1.3 | ColumnsnmpManagerCommunityName | read-only | mandatory | The community string name used by the manager. |
| 1.3.6.1.4.1.7262.1.21.3.1.4 | ColumnsnmpManagerActivated | read-only | mandatory | Specifies whether a specific manager is allowed to access the system |
| 1.3.6.1.4.1.7262.1.21.4 | TablesnmpV3ManagersTable | not-accessible | mandatory | Table containing snmp V3 manager entries |
| 1.3.6.1.4.1.7262.1.21.4.1 | RowsnmpV3ManagersEntry | not-accessible | mandatory | Contains the snmp v3 manager information |
| 1.3.6.1.4.1.7262.1.21.4.1.1 | ColumnsnmpV3ManagersIndex | read-only | mandatory | A unique value for each v3 manager. |
| 1.3.6.1.4.1.7262.1.21.4.1.2 | ColumnsnmpV3ManagerUserName | read-only | mandatory | The user name of the v3 Manager. |
| 1.3.6.1.4.1.7262.1.21.4.1.3 | ColumnsnmpV3ManagerAuthProtocol | read-only | mandatory | The authentication alogorithm used by the v3 manager. |
| 1.3.6.1.4.1.7262.1.21.4.1.4 | ColumnsnmpV3ManagerAuthPassword | read-only | mandatory | The authentication password of the v3 Manager. |
| 1.3.6.1.4.1.7262.1.21.4.1.5 | ColumnsnmpV3ManagerPrivProtocol | read-only | mandatory | The privacy encryiption alogorithm used by the v3 manager. |
| 1.3.6.1.4.1.7262.1.21.4.1.6 | ColumnsnmpV3ManagerPrivPassword | read-only | mandatory | The privacy password of the v3 Manager. |
| 1.3.6.1.4.1.7262.1.21.4.1.7 | ColumnsnmpV3ManagerActivated | read-only | mandatory | Specifies whether a specific v3 manager is allowed to access the system |
| 1.3.6.1.4.1.7262.1.22 | NodeapLinkAnalysis | |||
| 1.3.6.1.4.1.7262.1.22.1 | Scalarunits | read-only | mandatory | OBSOLETE. The units of measurement used in the link analysis. |
| 1.3.6.1.4.1.7262.1.22.2 | ScalardistanceInputMethod | read-only | mandatory | OBSOLETE. The input method used that determines whether distance between nodes coordinates were used for system calculations. |
| 1.3.6.1.4.1.7262.1.22.3 | ScalardistanceBetweenNodes | read-only | mandatory | OBSOLETE. The distance between nodes, in either meters, or feet, depending on the the Units used. This object will be 0 if Longitude and Latitude are used. |
| 1.3.6.1.4.1.7262.1.22.4 | ScalarlatitudeThisNode | read-only | mandatory | OBSOLETE.The latitude of this node.This object will be 0 if DistanceBetweenNodes is used. |
| 1.3.6.1.4.1.7262.1.22.5 | ScalarlongitudeThisNode | read-only | mandatory | OBSOLETE. The longitude of this node.This object will be 0 if DistanceBetweenNodes is used. |
| 1.3.6.1.4.1.7262.1.22.6 | ScalarlatitudePeerNode | read-only | mandatory | OBSOLETE. The latitude of the peer node.This object will be 0 if DistanceBetweenNodes is used. |
| 1.3.6.1.4.1.7262.1.22.7 | ScalarlongitudePeerNode | read-only | mandatory | OBSOLETE. The longitude of the peer node.This object will be 0 if DistanceBetweenNodes is used. |
| 1.3.6.1.4.1.7262.1.22.8 | ScalarlinkAnalysisFrequencyBand | read-only | mandatory | OBSOLETE. The frequency band that this system was set up for |
| 1.3.6.1.4.1.7262.1.22.9 | ScalaravailabilityPercentage | read-only | mandatory | OBSOLETE. The required availability of the link. A value of 95999 is 95.000% |
| 1.3.6.1.4.1.7262.1.22.10 | Scalarpolarization | read-only | mandatory | OBSOLETE. The polarization of the node. |
| 1.3.6.1.4.1.7262.1.22.11 | ScalarlinkAnalysisAirPairType | read-only | mandatory | OBSOLETE. The AirPair type that this system was set up as |
| 1.3.6.1.4.1.7262.1.22.12 | ScalarrainRegion | read-only | mandatory | OBSOLETE. The rain region of the site. |
| 1.3.6.1.4.1.7262.1.22.13 | ScalarantennaDiameter | read-only | mandatory | OBSOLETE. The diameter of the antenna, in inches or centimeters. |
| 1.3.6.1.4.1.7262.1.22.14 | ScalartransmitPowerBackoff | read-only | mandatory | OBSOLETE. The transmitter back off power. |
| 1.3.6.1.4.1.7262.1.23 | NodeapCoS | |||
| 1.3.6.1.4.1.7262.1.23.1 | Scalardot1pFiltering | read-write | mandatory | Sets DotP1 filtering on/off. |
| 1.3.6.1.4.1.7262.1.23.2 | Scalardot1pValue0QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 0. |
| 1.3.6.1.4.1.7262.1.23.3 | Scalardot1pValue1QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 1. |
| 1.3.6.1.4.1.7262.1.23.4 | Scalardot1pValue2QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 2. |
| 1.3.6.1.4.1.7262.1.23.5 | Scalardot1pValue3QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 3. |
| 1.3.6.1.4.1.7262.1.23.6 | Scalardot1pValue4QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 4. |
| 1.3.6.1.4.1.7262.1.23.7 | Scalardot1pValue5QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 5. |
| 1.3.6.1.4.1.7262.1.23.8 | Scalardot1pValue6QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 6. |
| 1.3.6.1.4.1.7262.1.23.9 | Scalardot1pValue7QueueAssignment | read-write | mandatory | Queue assignment for DotP1 value 7. |
| 1.3.6.1.4.1.7262.1.23.10 | ScalarcosQueueWidth | read-write | mandatory | The class of service queue width. Enter a value from 1 to 16 to define the priority queues size. |
| 1.3.6.1.4.1.7262.1.24 | NodeapManagementSessions | |||
| 1.3.6.1.4.1.7262.1.24.1 | NodettySessionUser1 | |||
| 1.3.6.1.4.1.7262.1.24.1.1 | ScalarttySessionUser1Name | read-only | mandatory | The username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in pr… |
| 1.3.6.1.4.1.7262.1.24.1.2 | ScalarttySessionUser1ConnectionType | read-only | mandatory | The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on i… |
| 1.3.6.1.4.1.7262.1.24.1.3 | ScalarttySessionUser1State | read-only | mandatory | The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of th… |
| 1.3.6.1.4.1.7262.1.24.2 | NodettySessionUser2 | |||
| 1.3.6.1.4.1.7262.1.24.2.1 | ScalarttySessionUser2Name | read-only | mandatory | The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. |
| 1.3.6.1.4.1.7262.1.24.2.2 | ScalarttySessionUser2ConnectionType | read-only | mandatory | The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on i… |
| 1.3.6.1.4.1.7262.1.24.2.3 | ScalarttySessionUser2State | read-only | mandatory | The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of th… |
| 1.3.6.1.4.1.7262.1.24.3 | NodettySessionUser3 | |||
| 1.3.6.1.4.1.7262.1.24.3.1 | ScalarttySessionUser3Name | read-only | mandatory | The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. |
| 1.3.6.1.4.1.7262.1.24.3.2 | ScalarttySessionUser3ConnectionType | read-only | mandatory | The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on i… |
| 1.3.6.1.4.1.7262.1.24.3.3 | ScalarttySessionUser3State | read-only | mandatory | The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of th… |
| 1.3.6.1.4.1.7262.1.24.4 | NodettySessionUser4 | |||
| 1.3.6.1.4.1.7262.1.24.4.1 | ScalarttySessionUser4Name | read-only | mandatory | The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. |
| 1.3.6.1.4.1.7262.1.24.4.2 | ScalarttySessionUser4ConnectionType | read-only | mandatory | The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on i… |
| 1.3.6.1.4.1.7262.1.24.4.3 | ScalarttySessionUser4State | read-only | mandatory | The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of th… |
| 1.3.6.1.4.1.7262.1.24.5 | NodettySessionUser5 | |||
| 1.3.6.1.4.1.7262.1.24.5.1 | ScalarttySessionUser5Name | read-only | mandatory | The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. |
| 1.3.6.1.4.1.7262.1.24.5.2 | ScalarttySessionUser5ConnectionType | read-only | mandatory | The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on i… |
| 1.3.6.1.4.1.7262.1.24.5.3 | ScalarttySessionUser5State | read-only | mandatory | The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of th… |
| 1.3.6.1.4.1.7262.1.24.6 | NodettySessionUser6 | |||
| 1.3.6.1.4.1.7262.1.24.6.1 | ScalarttySessionUser6Name | read-only | mandatory | The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. |
| 1.3.6.1.4.1.7262.1.24.6.2 | ScalarttySessionUser6ConnectionType | read-only | mandatory | The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on i… |
| 1.3.6.1.4.1.7262.1.24.6.3 | ScalarttySessionUser6State | read-only | mandatory | The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of th… |
| 1.3.6.1.4.1.7262.1.24.7 | NodesessionUserInterformation | |||
| 1.3.6.1.4.1.7262.1.24.7.1 | ScalarttySessionUserName | read-only | mandatory | NOT IMPLEMENTED. Object type placeholder for username string for SNMP traps. The username of a person currently logged in to the system using Telnet or HTTP. T… |
| 1.3.6.1.4.1.7262.1.24.7.2 | ScalarttySessionUserConnectionType | read-only | mandatory | NOT IMPLEMENTED. Object type placeholder for connection type for SNMP traps. The physical port used to log in to the system. The serial port is always local to… |
| 1.3.6.1.4.1.7262.1.25 | NodeapInstall | |||
| 1.3.6.1.4.1.7262.1.25.1 | ScalarapInstallationType | read-only | mandatory | The AirPair installation type. All ODU or IDU-ODU split |
| 1.3.6.1.4.1.7262.1.25.2 | ScalarapRxCableLoss | read-only | mandatory | Rx cable loss. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.25.3 | ScalarapTxCableLoss | read-only | mandatory | Tx cable loss. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.25.4 | ScalarapFan1Status | read-only | mandatory | The fan 1 status. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.25.5 | ScalarapFan2Status | read-only | mandatory | The fan 2 status. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.25.6 | ScalarapFanTestMode | read-write | mandatory | This operation turns on or off fan test mode. Fan test mode forces all fans in the system to on. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.25.7 | ScalarapCableLossChange | read-only | mandatory | Cable loss change. Valid only when the installation type is IDU-ODU split |
| 1.3.6.1.4.1.7262.1.27 | NodehttpSecure | |||
| 1.3.6.1.4.1.7262.1.27.1 | ScalarhttpSecureCertificateStatus | read-only | mandatory | Returns the HTTPS certificate status |
| 1.3.6.1.4.1.7262.1.27.2 | ScalarhttpSecureAccessForAdminUsers | read-write | mandatory | the HTTPS access requirement for Admin user group. |
| 1.3.6.1.4.1.7262.1.27.3 | ScalarhttpSecureAccessForNocUsers | read-write | mandatory | the HTTPS access requirement for Noc user group. |
| 1.3.6.1.4.1.7262.1.27.4 | ScalarhttpSecureAccessForSuperUsers | read-write | mandatory | the HTTPS access requirement for Super user group. |
| 1.3.6.1.4.1.7262.1.28 | NodegigaEQos | |||
| 1.3.6.1.4.1.7262.1.28.1 | ScalarqosEnable | read-write | mandatory | Indicates whether gigabit Ethernet QOS is enabled. |
| 1.3.6.1.4.1.7262.1.28.2 | Scalardot1pValue0To7VsQueueMapping | read-write | mandatory | User queue assignments for Dot1P values 0 to 7. Dot1P value 0 is lowest priority and Dot1P value 7 is highest priority. We have 4 user queues. Their correspond… |
| 1.3.6.1.4.1.7262.1.28.3 | ScalarqueueOperationMode | read-write | mandatory | This sets the user queue operation mode. (a) In expedite mode, User Queue 4 has 100% of CIR. User Queue 4 will be serviced until it is empty. (b) In non expedi… |
| 1.3.6.1.4.1.7262.1.28.4 | ScalaruserQueue1To4CIRs | read-write | mandatory | Committeed Information Rate (CIR) assignments for user queues 1 to 4. CIR is the percentage of maximum bandwidth for user traffic. (a) In queue operation exped… |
| 1.3.6.1.4.1.7262.1.28.5 | ScalaruserQueue1To4PBS | read-write | mandatory | Peak Burst Size (PBS) for user queues 1 to 4. PBS is the percentage of total user queue packet buffer size. The sum of PBS's of all 4 user queues must not exce… |
| 1.3.6.1.4.1.7262.1.28.6 | ScalardefaultQosValue | read-write | mandatory | Default Qos value is the assigned 802.1p value for the ethernet frames that don't have dot1p tagged. |
| 1.3.6.1.4.1.7262.1.29 | NoderapidLinkShutdown | |||
| 1.3.6.1.4.1.7262.1.29.1 | ScalarrlsEnable | read-write | mandatory | The Rapid Link Shutdown feature: enabled or disabled. Changing this option requires a system reset. |
| 1.3.6.1.4.1.7262.1.29.2 | ScalarautomaticLinkReestablish | read-write | mandatory | If this feature is enabled, the link will be automatically reestablihedl If this feature is disabled, the user must explicitly use the manualReestablish object… |
| 1.3.6.1.4.1.7262.1.29.3 | ScalarmanualLinkReestablish | read-write | mandatory | This object is writeable ONLY if automaticLinkReestablish is set to disabled. The user explicitly brings the link back up by setting this object to enabled. Th… |
| 1.3.6.1.4.1.7262.1.29.4 | ScalarhysterisisErredFramesPerMilliSecond | read-write | mandatory | The link will be automatically shut down when this number of erred modem frames threshold is exceeded during the time set in the hysterisisErredMilliSeconds ob… |
| 1.3.6.1.4.1.7262.1.29.5 | ScalarhysterisisErredMilliSeconds | read-write | mandatory | The time to determine a link that has excessive errors. The link will be automatically shut down when this number of milliseconds experiences the number of err… |
| 1.3.6.1.4.1.7262.1.29.6 | ScalarhysterisisUnerredFramesPerMilliSecond | read-write | mandatory | The link will be automatically brought back up when the number of erred modem frames is less than this value ( only if automaticLinkReestablish is set to enabl… |
| 1.3.6.1.4.1.7262.1.29.7 | ScalarhysterisisUnerredMilliSeconds | read-write | mandatory | The time block to use to determine if the link is error free enough to warrant it to automatically reestablish itself ( only if automaticLinkReestablish is set… |
| 1.3.6.1.4.1.7262.1.29.8 | ScalarwriteRlsMonitorParametersToSystem | read-write | mandatory | This writes the following parameters to RAM: hysterisisErredFramesPerMilliSecond, hysterisisErredMilliSeconds, hysterisisUnerredFramesPerMilliSecond, hysterisi… |
| 1.3.6.1.4.1.7262.1.29.9 | ScalarrlsAdvancedAlgorithm | read-write | mandatory | When it is on RLS advanced algorithm is used, otherwise RLS advanced algorithm is not used. |
| 1.3.6.1.4.1.7262.1.29.10 | ScalarrlsSampleTimeInMilliSeconds | read-write | mandatory | |
| 1.3.6.1.4.1.7262.1.30 | Nodesntp | |||
| 1.3.6.1.4.1.7262.1.30.1 | ScalarsntpEnable | read-write | mandatory | Indicates whether SNTP feature is enabled. |
| 1.3.6.1.4.1.7262.1.30.2 | ScalarsntpOffset | read-write | mandatory | System time offset from GMT. |
| 1.3.6.1.4.1.7262.1.30.3 | TablesntpServerTable | not-accessible | mandatory | Table containing sntp server entries |
| 1.3.6.1.4.1.7262.1.30.3.1 | RowsntpServerEntry | not-accessible | mandatory | Contains the sntp server information |
| 1.3.6.1.4.1.7262.1.30.3.1.1 | ColumnsntpServerIndex | read-only | mandatory | A unique value for each server. |
| 1.3.6.1.4.1.7262.1.30.3.1.2 | ColumnsntpServerIpAddress | read-write | mandatory | The IP address of the server. |
| 1.3.6.1.4.1.7262.1.30.3.1.3 | ColumnsntpServerStatus | read-only | mandatory | The status of the sntp server. |
| 1.3.6.1.4.1.7262.1.30.3.1.4 | ColumnsntpServerStratum | read-only | mandatory | Specifies the stratum of a server, 0 for failed server |
| 1.3.6.1.4.1.7262.1.31 | NodeapLogs | |||
| 1.3.6.1.4.1.7262.1.31.1 | ScalareventLogEnable | read-write | mandatory | Indicates whether event log is enabled. |
| 1.3.6.1.4.1.7262.1.31.2 | ScalarperfmLogEnable | read-write | mandatory | Indicates whether performance log is enabled. |
| 1.3.6.1.4.1.7262.1.31.3 | ScalarperfmLogInterval | read-write | mandatory | Performance statistics are logged periodically by this interval. |
| 1.3.6.1.4.1.7262.1.32 | Noderadius | |||
| 1.3.6.1.4.1.7262.1.32.1 | ScalarsuperUserAuthentication | read-write | mandatory | The set strict mode on or off |
| 1.3.6.1.4.1.7262.1.32.2 | ScalarserverTimeOut | read-only | mandatory | Timeout period for authentication requests |
| 1.3.6.1.4.1.7262.1.32.3 | ScalarserverDeadTime | read-only | mandatory | Time to declare an unresponsive server 'dead' |
| 1.3.6.1.4.1.7262.1.32.4 | ScalarserverReTransmit | read-only | mandatory | Maximum number of retransmits to an unresponsive server |
| 1.3.6.1.4.1.7262.1.32.5 | TableradiusServerTable | not-accessible | mandatory | Table containing radius server entries |
| 1.3.6.1.4.1.7262.1.32.5.1 | RowradiusServerEntry | not-accessible | mandatory | Contains the sntp server information |
| 1.3.6.1.4.1.7262.1.32.5.1.1 | ColumnradiusServerIndex | read-only | mandatory | A unique value for each server. |
| 1.3.6.1.4.1.7262.1.32.5.1.2 | ColumncfgdHostIpAddress | read-write | mandatory | The IP address of the configured radius server. |
| 1.3.6.1.4.1.7262.1.32.5.1.3 | ColumnactiveHostIpAddress | read-only | mandatory | The IP address of the active radius server. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING | ||
| PhysAddress | OCTET STRING |