BIANCA-BOX-ISDN-MIB
164 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC1155-SMI | Counter OBJECT-TYPE TimeTicks |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3 | Nodeorg | |||
| 1.3.6 | Nodedod | |||
| 1.3.6.1 | Nodeinternet | |||
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.272 | Nodebintec | |||
| 1.3.6.1.4.1.272.4 | Nodebibo | |||
| 1.3.6.1.4.1.272.4.2 | Nodeisdn | |||
| 1.3.6.1.4.1.272.4.2.1 | TableisdnIfTable | not-accessible | mandatory | The isdnIfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected ISDN interface (BRI or PRI). Entries… |
| 1.3.6.1.4.1.272.4.2.1.1 | RowisdnIfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.1.1.1 | ColumnisdnIfIndex | read-only | mandatory | Unique index of the basic or primary rate interface. |
| 1.3.6.1.4.1.272.4.2.1.1.2 | ColumnisdnIfDescription | read-only | mandatory | Textual description of the basic rate interface including its slot and number (e.g. bri2-0 means slot 2, unit 0). |
| 1.3.6.1.4.1.272.4.2.1.1.3 | ColumnisdnIfLayer1State | read-only | mandatory | The ISDN physical layer state according to I.430 f1(1) = inactive; f2(2) = sensing; f3(3) = deactivated; f4(4) = awaiting signal; f5(5) = identifying input; f6… |
| 1.3.6.1.4.1.272.4.2.1.1.4 | ColumnisdnIfBchannelControl | read-only | mandatory | B-channels are controlled by a call control protocol in the D-channel. Otherwise they may be used as permanent links. |
| 1.3.6.1.4.1.272.4.2.1.1.5 | ColumnisdnIfActivationRequest | read-write | mandatory | When this object is set to 'activate' the BRICK will start an activation sequence of ISDN-Layer1 of the basic rate interface. |
| 1.3.6.1.4.1.272.4.2.1.1.6 | ColumnisdnIfMode | read-write | mandatory | Specifies the mode of the interface. TE or NT Mode will be set for ISDN interfaces without PABX control. For PRI both NT (network termination) and TE (terminal… |
| 1.3.6.1.4.1.272.4.2.1.1.7 | ColumnisdnIfTimerT3 | read-write | mandatory | Value of Timer T3 in milliseconds.T3 is started whenever ISDNLayer-1 is activated (i.e. Activation Request is started). |
| 1.3.6.1.4.1.272.4.2.1.1.8 | ColumnisdnIfUsePowerDetector | read-write | mandatory | Use the PS1 Power Detector to control the layer 1 automaton.This object is only valid for basic rate interfaces. |
| 1.3.6.1.4.1.272.4.2.1.1.9 | ColumnisdnIfNumberOfChannels | read-only | mandatory | Number of Channels including the D channel, that are available on this ISDN Interface (3 = BRI, 31 = PRI). |
| 1.3.6.1.4.1.272.4.2.1.1.10 | ColumnisdnIfTimeouts | read-only | mandatory | Number of timeouts of T3 during lifetime of the system. |
| 1.3.6.1.4.1.272.4.2.1.1.11 | ColumnisdnIfActivates | read-only | mandatory | Number of successful activation cycles during lifetime of the system. |
| 1.3.6.1.4.1.272.4.2.1.1.12 | ColumnisdnIfDeactivates | read-only | mandatory | Number of deactivations during lifetime of the system. |
| 1.3.6.1.4.1.272.4.2.1.1.13 | ColumnisdnIfAutoconfigState | read-write | mandatory | Start auto configuration on this ISDN Interface. Auto configuration is a mechanism to automatically detect the attributes of an ISDN interface. This can be don… |
| 1.3.6.1.4.1.272.4.2.1.1.14 | ColumnisdnIfAutoconfig | read-write | mandatory | Start Autoconfiguration on this ISDN interface at bootup. |
| 1.3.6.1.4.1.272.4.2.1.1.21 | ColumnisdnIfSlips | read-only | mandatory | Slip conditions detected since startup. Flags that the frequency of receive clock is different than frequency of internal system clock. |
| 1.3.6.1.4.1.272.4.2.2 | TableisdnChTable | not-accessible | mandatory | The isdnChTable contains information for each physical B or D channel on the system. The entries contain information regarding the configuration of the channel… |
| 1.3.6.1.4.1.272.4.2.2.1 | RowisdnChEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.2.1.1 | ColumnisdnChIsdnIfIndex | read-only | mandatory | Unique index of an Interface. |
| 1.3.6.1.4.1.272.4.2.2.1.2 | ColumnisdnChNumber | read-only | mandatory | The channel number. 0 is D-channel, 1..2 are the B- channels of a BRI module, and 1..31 are the B-channels of a PRI module. |
| 1.3.6.1.4.1.272.4.2.2.1.3 | ColumnisdnChState | read-only | mandatory | Status of the Channel controlled either by the call control protocol or the physical state of the interface. |
| 1.3.6.1.4.1.272.4.2.2.1.4 | ColumnisdnChType | read-write | mandatory | Type of Channel.Setting this object to one of the leased values creates a new entry in the ifTable. |
| 1.3.6.1.4.1.272.4.2.2.1.5 | ColumnisdnChBundle | read-write | mandatory | Index of the bundle to aggregate multiple Channels to one interface. Not valid in dialup mode. |
| 1.3.6.1.4.1.272.4.2.2.1.6 | ColumnisdnChThroughput | read-only | mandatory | Throughput of the channel in bits/second (64000 for B-channels, 16000 for BRI D-Channels. |
| 1.3.6.1.4.1.272.4.2.2.1.7 | ColumnisdnChReceivedPackets | read-only | mandatory | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.2.1.8 | ColumnisdnChReceivedOctets | read-only | mandatory | Count of received valid HDLC bytes. |
| 1.3.6.1.4.1.272.4.2.2.1.9 | ColumnisdnChReceivedErrors | read-only | mandatory | Count of received valid errors (can be detected by HDLC-Checksum-Errors). |
| 1.3.6.1.4.1.272.4.2.2.1.10 | ColumnisdnChTransmitPackets | read-only | mandatory | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.2.1.11 | ColumnisdnChTransmitOctets | read-only | mandatory | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.2.1.12 | ColumnisdnChTransmitErrors | read-only | mandatory | Count of transmitted valid HDLC errors. Can occur when the transmitter can not be reloaded fast enough when transmitting large packets. This should only happen… |
| 1.3.6.1.4.1.272.4.2.3 | TableisdnStkTable | not-accessible | mandatory | The isdnStkTable contains information for each ISDN protocol stack currently configured on the system. Entries are normally created by the system at boot time,… |
| 1.3.6.1.4.1.272.4.2.3.1 | RowisdnStkEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.3.1.1 | ColumnisdnStkNumber | read-write | mandatory | Unique number of an ISDN stack (0..n). This number can be used in the isdnDispatchTable. |
| 1.3.6.1.4.1.272.4.2.3.1.3 | ColumnisdnStkIsdnIfIndex | read-write | mandatory | The index of the ISDN interface. The isdnIfTable lists all available ISDN interfaces. |
| 1.3.6.1.4.1.272.4.2.3.1.4 | ColumnisdnStkProtocolProfile | read-write | mandatory | The protocol for the D channel. Assigning `delete' to this object has the effect of removing the entry from this table. |
| 1.3.6.1.4.1.272.4.2.3.1.5 | ColumnisdnStkConfiguration | read-write | mandatory | |
| 1.3.6.1.4.1.272.4.2.3.1.6 | ColumnisdnStkSPID | read-write | mandatory | The service profile identifier; only required for the national ISDN1 protocol in North America. |
| 1.3.6.1.4.1.272.4.2.3.1.7 | ColumnisdnStkTeiProc | read-write | mandatory | The Tei procedure used. Note that for point-to-point configurations this object should be set to fixed(2). |
| 1.3.6.1.4.1.272.4.2.3.1.8 | ColumnisdnStkTeiValue | read-write | mandatory | The Tei value. Note that for point-to-point configurations this object should be 0. |
| 1.3.6.1.4.1.272.4.2.3.1.22 | ColumnisdnStkClearAllCalls | read-write | mandatory | Setting this value to clear(2) will force all current connections on this stack to terminate. |
| 1.3.6.1.4.1.272.4.2.3.1.23 | ColumnisdnStkStatus | read-only | mandatory | Shows the status of this ISDN stack. If auto configuration was successful for this stack, this object will be loaded(1). If this stack is not loaded, ISDN call… |
| 1.3.6.1.4.1.272.4.2.3.1.24 | ColumnisdnStkLayer2State | read-only | mandatory | Shows the current state of Layer2. To allow ISDN connections, the state established(4) must be assigned. |
| 1.3.6.1.4.1.272.4.2.3.1.25 | ColumnisdnStkBchannels | read-write | mandatory | Number of B channels that correspond to that stack. |
| 1.3.6.1.4.1.272.4.2.3.1.26 | ColumnisdnStkDialOutPrefix | read-write | mandatory | Prefix for PABX dialout. This entry is added to a dialing number provided by the calling site via PPP negotiation (LCP Callback Option / PPP Bandwith Alllocati… |
| 1.3.6.1.4.1.272.4.2.4 | TableisdnCallTable | not-accessible | mandatory | The isdnCallTable displays all currently active ISDN calls (incoming and outgoing). Only the system can add or remove entries to this table. Creating entries: … |
| 1.3.6.1.4.1.272.4.2.4.1 | RowisdnCallEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.4.1.1 | ColumnisdnCallStkNumber | read-only | mandatory | The number of the ISDN-Stack, this call is going through. Refer to the isdnStkTable. |
| 1.3.6.1.4.1.272.4.2.4.1.2 | ColumnisdnCallType | read-only | mandatory | The direction of the call. |
| 1.3.6.1.4.1.272.4.2.4.1.3 | ColumnisdnCallReference | read-only | mandatory | The corresponding Call-Reference Value on the ISDN D-channel. |
| 1.3.6.1.4.1.272.4.2.4.1.4 | ColumnisdnCallAge | read-only | mandatory | The age of the call. For outgoing calls, the time since the call began, or for incoming calls, the time since the call was received. The format is in hh:mm:ss.… |
| 1.3.6.1.4.1.272.4.2.4.1.5 | ColumnisdnCallState | read-write | mandatory | The state of the call. |
| 1.3.6.1.4.1.272.4.2.4.1.6 | ColumnisdnCallIsdnIfIndex | read-only | mandatory | The corresponding ISDN interface that is used for this call. Refer to the isdnIfTable. |
| 1.3.6.1.4.1.272.4.2.4.1.7 | ColumnisdnCallChannel | read-only | mandatory | The corresponding B-channel on this ISDN interface. Refer to the isdnIfTable. |
| 1.3.6.1.4.1.272.4.2.4.1.8 | ColumnisdnCallDspItem | read-only | mandatory | The item to or from which this call is connected. For any routing tasks (IP, IPX, X.25, bridging, ...) the ppp(1) item is used. For the isdnlogin program, logi… |
| 1.3.6.1.4.1.272.4.2.4.1.9 | ColumnisdnCallRemoteNumber | read-only | mandatory | The ISDN number that was called (for outgoing calls) or was calling (for incoming calls). |
| 1.3.6.1.4.1.272.4.2.4.1.10 | ColumnisdnCallRemoteSubaddress | read-only | mandatory | The subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnCallRemoteNumber. |
| 1.3.6.1.4.1.272.4.2.4.1.11 | ColumnisdnCallLocalNumber | read-only | mandatory | The calling party number that was sent (with the outgoing call) or was received (with incoming calls). Refer to the isdnStkTable. |
| 1.3.6.1.4.1.272.4.2.4.1.12 | ColumnisdnCallLocalSubaddress | read-only | mandatory | The subaddress of the calling party number. See isdnCallRLocalNumber. |
| 1.3.6.1.4.1.272.4.2.4.1.13 | ColumnisdnCallServiceIndicator | read-only | mandatory | Service indicator that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.4.1.14 | ColumnisdnCallAddInfo | read-only | mandatory | Additional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol. |
| 1.3.6.1.4.1.272.4.2.4.1.15 | ColumnisdnCallBC | read-only | mandatory | Bearer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.4.1.16 | ColumnisdnCallLLC | read-only | mandatory | Low Layer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.4.1.17 | ColumnisdnCallHLC | read-only | mandatory | The number of charging ticks received since this connection was established. Actual charges can be computed by multiplying this value with the unit price (e.g.… |
| 1.3.6.1.4.1.272.4.2.4.1.18 | ColumnisdnCallCharge | read-only | mandatory | This object contains the charge for this call either as units or as 1/1000 of the respective currency. Which type of information is choosen, depends on the inf… |
| 1.3.6.1.4.1.272.4.2.4.1.19 | ColumnisdnCallReceivedPackets | read-only | mandatory | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.4.1.20 | ColumnisdnCallReceivedOctets | read-only | mandatory | Count of received valid HDLC Octets. |
| 1.3.6.1.4.1.272.4.2.4.1.21 | ColumnisdnCallReceivedErrors | read-only | mandatory | Count of received invalid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.4.1.22 | ColumnisdnCallTransmitPackets | read-only | mandatory | Count of transmitted HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.4.1.23 | ColumnisdnCallTransmitOctets | read-only | mandatory | Count of transmitted Octets. |
| 1.3.6.1.4.1.272.4.2.4.1.24 | ColumnisdnCallTransmitErrors | read-only | mandatory | Count of transmit errors (Collision, TX underrun). |
| 1.3.6.1.4.1.272.4.2.4.1.25 | ColumnisdnCallChargeInfo | read-only | mandatory | Textual information of charge, i.e. 0.12 DM or 3 units |
| 1.3.6.1.4.1.272.4.2.4.1.26 | ColumnisdnCallScreening | read-only | mandatory | Screening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by th… |
| 1.3.6.1.4.1.272.4.2.4.1.27 | ColumnisdnCallInfo | read-only | mandatory | Additional information to identify the call |
| 1.3.6.1.4.1.272.4.2.5 | TableisdnDispatchTable | not-accessible | mandatory | The isdnDispatchTable is the central distribution center for all incoming ISDN connections. Incoming ISDN connections are `dispatched' to a service (isdnDspIte… |
| 1.3.6.1.4.1.272.4.2.5.1 | RowisdnDispatchEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.5.1.1 | ColumnisdnDspStkNumber | read-write | mandatory | The ISDN stack number for this entry. |
| 1.3.6.1.4.1.272.4.2.5.1.2 | ColumnisdnDspItem | read-write | mandatory | The item to connect this call to. Routing tasks (IP, IPX, X.25, bridging, ...) should use the ppp(1). For the isdnlogin program use the login(2) item. For CAPI… |
| 1.3.6.1.4.1.272.4.2.5.1.3 | ColumnisdnDspLocalNumber | read-write | mandatory | If the Called Party Number of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing calls … |
| 1.3.6.1.4.1.272.4.2.5.1.4 | ColumnisdnDspLocalSubaddress | read-write | mandatory | If the Called Party Subaddress of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing ca… |
| 1.3.6.1.4.1.272.4.2.5.1.5 | ColumnisdnDspBearer | read-write | mandatory | The isdnDspBearer is used for dispatching different types of calls |
| 1.3.6.1.4.1.272.4.2.5.1.6 | ColumnisdnDspSlot | read-write | mandatory | Identification number of the used slot. |
| 1.3.6.1.4.1.272.4.2.5.1.7 | ColumnisdnDspUnit | read-write | mandatory | Identification number of the used unit. |
| 1.3.6.1.4.1.272.4.2.5.1.8 | ColumnisdnDspDirection | read-write | mandatory | Specifies whether the entry is to be used for outgoing calls, incoming calls or both. |
| 1.3.6.1.4.1.272.4.2.5.1.9 | ColumnisdnDspMode | read-write | mandatory | This object specifies the matching direction for incoming calls. When set to right-to-left, the rightmost digits of the called address of an incoming call are … |
| 1.3.6.1.4.1.272.4.2.5.1.10 | ColumnisdnDspUserName | read-write | mandatory | The name of the user. |
| 1.3.6.1.4.1.272.4.2.6 | TableisdnDChanX31Table | not-accessible | mandatory | The isdnDChanX31Table contains information for the X.31 stack for each available ISDN D-channel. This information is mainly used for X.25 packet-switching func… |
| 1.3.6.1.4.1.272.4.2.6.1 | RowisdnDChanX31Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.6.1.1 | ColumnisdnX31IsdnIfIndex | read-write | mandatory | The corresponding ISDN interface that is used for this call. Refer to the isdnIfTable. |
| 1.3.6.1.4.1.272.4.2.6.1.2 | ColumnisdnX31TeiProc | read-write | mandatory | The procedure used for polling of TEI (terminal end-point identifiers) values. |
| 1.3.6.1.4.1.272.4.2.6.1.3 | ColumnisdnX31TeiValue | read-write | mandatory | The TEI value for this interface. |
| 1.3.6.1.4.1.272.4.2.6.1.5 | ColumnisdnX31AssignedTo | read-write | mandatory | The service this TEI value is assigned to. |
| 1.3.6.1.4.1.272.4.2.7 | ScalarisdnAccountingTemplate | read-write | mandatory | Specifies the format of accounting messages sent by the syslog protocol. The format can consist of any order of the following variables. Tag Meaning %S Date th… |
| 1.3.6.1.4.1.272.4.2.8 | TableisdnCallHistoryTable | not-accessible | mandatory | The isdnCallHistoryTable contains information pertaining to the last 20 ISDN calls made, since the last system startup. Each call that appears in the isdnCallT… |
| 1.3.6.1.4.1.272.4.2.8.1 | RowisdnCallHistoryEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.8.1.1 | ColumnisdnCallHistoryStkNumber | read-only | mandatory | The number of the ISDN-Stack, this call went through. |
| 1.3.6.1.4.1.272.4.2.8.1.2 | ColumnisdnCallHistoryType | read-only | mandatory | The direction of the call, incoming or outgoing. |
| 1.3.6.1.4.1.272.4.2.8.1.3 | ColumnisdnCallHistoryTime | read-only | mandatory | The time the call was received (incoming) or was placed (outgoing). |
| 1.3.6.1.4.1.272.4.2.8.1.4 | ColumnisdnCallHistoryDuration | read-only | mandatory | The duration of the call in seconds. |
| 1.3.6.1.4.1.272.4.2.8.1.5 | ColumnisdnCallHistoryIsdnIfIndex | read-only | mandatory | The corresponding ISDN interface that this call used. |
| 1.3.6.1.4.1.272.4.2.8.1.6 | ColumnisdnCallHistoryChannel | read-only | mandatory | The corresponding B-channel on this ISDN interface. |
| 1.3.6.1.4.1.272.4.2.8.1.7 | ColumnisdnCallHistoryDspItem | read-only | mandatory | The item this call was connected to. Routing tasks (IP, IPX, X.25, bridging, ...) use ppp(1). The isdnlogin program uses login(2). CAPI 1.1 programs, use the i… |
| 1.3.6.1.4.1.272.4.2.8.1.8 | ColumnisdnCallHistoryRemoteNumber | read-only | mandatory | The ISDN number that was called (for outgoing calls) or was calling (for incoming calls). |
| 1.3.6.1.4.1.272.4.2.8.1.9 | ColumnisdnCallHistoryRemoteSubaddress | read-only | mandatory | The subaddress of the remote number. See isdnCall- HistoryRemoteNumber. |
| 1.3.6.1.4.1.272.4.2.8.1.10 | ColumnisdnCallHistoryLocalNumber | read-only | mandatory | The calling party number that was sent (with the outgoing call) or was received (with incoming calls). |
| 1.3.6.1.4.1.272.4.2.8.1.11 | ColumnisdnCallHistoryLocalSubaddress | read-only | mandatory | The subaddress of the calling party number. |
| 1.3.6.1.4.1.272.4.2.8.1.12 | ColumnisdnCallHistoryServiceIndicator | read-only | mandatory | Service indicator that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.8.1.13 | ColumnisdnCallHistoryAddInfo | read-only | mandatory | Additional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol. |
| 1.3.6.1.4.1.272.4.2.8.1.14 | ColumnisdnCallHistoryBC | read-only | mandatory | Bearer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.8.1.15 | ColumnisdnCallHistoryLLC | read-only | mandatory | Low Layer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.8.1.16 | ColumnisdnCallHistoryHLC | read-only | mandatory | High Layer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.272.4.2.8.1.17 | ColumnisdnCallHistoryCharge | read-only | mandatory | The number of charging ticks received for this connection. Actual charges can be computed by multiplying this value with the unit price, e.g. .12 DM in Germany… |
| 1.3.6.1.4.1.272.4.2.8.1.18 | ColumnisdnCallHistoryDSS1Cause | read-only | mandatory | ISDN error condition reported by the DSS1 protocol, for Euro ISDN. See Appendix C in the User's Guide. |
| 1.3.6.1.4.1.272.4.2.8.1.19 | ColumnisdnCallHistory1TR6Cause | read-only | mandatory | ISDN error condition reported by the 1TR6 protocol, for National ISDN in Germany. See Appendix C in the User's Guide. |
| 1.3.6.1.4.1.272.4.2.8.1.20 | ColumnisdnCallHistoryLocalCause | read-only | mandatory | ISDN error condition reported by the system locally. See Appendix C in the User's Guide. |
| 1.3.6.1.4.1.272.4.2.8.1.21 | ColumnisdnCallHistoryChargeInfo | read-only | mandatory | Textual information of charge, i.e. 0.12 DM or 3 units |
| 1.3.6.1.4.1.272.4.2.8.1.22 | ColumnisdnCallHistoryScreening | read-only | mandatory | Screening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by th… |
| 1.3.6.1.4.1.272.4.2.8.1.23 | ColumnisdnCallHistoryInfo | read-only | mandatory | Additional information to identify the call |
| 1.3.6.1.4.1.272.4.2.8.1.24 | ColumnisdnCallHistoryReceivedPackets | read-only | mandatory | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.8.1.25 | ColumnisdnCallHistoryReceivedOctets | read-only | mandatory | Count of received valid HDLC Octets. |
| 1.3.6.1.4.1.272.4.2.8.1.26 | ColumnisdnCallHistoryReceivedErrors | read-only | mandatory | Count of received invalid HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.8.1.27 | ColumnisdnCallHistoryTransmitPackets | read-only | mandatory | Count of transmitted HDLC Frames. |
| 1.3.6.1.4.1.272.4.2.8.1.28 | ColumnisdnCallHistoryTransmitOctets | read-only | mandatory | Count of transmitted Octets. |
| 1.3.6.1.4.1.272.4.2.8.1.29 | ColumnisdnCallHistoryTransmitErrors | read-only | mandatory | Count of transmit errors (Collision, TX underrun). |
| 1.3.6.1.4.1.272.4.2.9 | ScalarisdnLoginOnPPPDispatch | read-write | mandatory | Allows or disallows incoming ISDN calls (with an ISDN service indicator of 'telephony'), to be connected to the isdnlogin daemon even though the call has a mat… |
| 1.3.6.1.4.1.272.4.2.10 | ScalarisdnHistoryMaxEntries | read-write | mandatory | Maximum number of isdnCallHistory entries in memory. |
| 1.3.6.1.4.1.272.4.2.11 | TableisdnloginAllowTable | not-accessible | mandatory | The isdnloginAllowTable contains information about the ISDN partners that are allowed to login to the BRICK via the isdnlogin service. ISDN callers are identif… |
| 1.3.6.1.4.1.272.4.2.11.1 | RowisdnloginAllowEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.11.1.1 | ColumnisdnloginAllowStkNumber | read-write | mandatory | The number of the ISDN stack, that accepts incoming isdnlogin calls. Refer to the isdnStkTable. The value `-1' matches all available stacks. |
| 1.3.6.1.4.1.272.4.2.11.1.2 | ColumnisdnloginAllowRemoteNumber | read-write | mandatory | The number of the ISDN partner that is allowed to login via isdnlogin through the corresponding ISDN Stack. The wildcards '*', '?', '[', ']', '{', '}' may be u… |
| 1.3.6.1.4.1.272.4.2.11.1.3 | ColumnisdnloginAllowRemoteSubaddress | read-write | mandatory | The subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnloginAllowRemoteNumber. |
| 1.3.6.1.4.1.272.4.2.11.1.4 | ColumnisdnloginAllowScreening | read-write | mandatory | The screening indicator of the calling party number (CPN). The isdnloginAllowScreening field can be used to gauge the `trustworthiness' of the CPN field (see i… |
| 1.3.6.1.4.1.272.4.2.12 | TableisdnCreditsTable | not-accessible | mandatory | The isdnCreditsTable contains informations about current used resources and maximum allowed resources for each during a specified interval subsystem. Creating … |
| 1.3.6.1.4.1.272.4.2.12.1 | RowisdnCreditsEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.2.12.1.1 | ColumnisdnCreditsSubsysNumber | read-only | mandatory | Type of Subsystem. |
| 1.3.6.1.4.1.272.4.2.12.1.2 | ColumnisdnCreditsSurveillance | read-write | mandatory | Surveillance on or off. |
| 1.3.6.1.4.1.272.4.2.12.1.3 | ColumnisdnCreditsMeasuretime | read-write | mandatory | Time of one observation interval in seconds. |
| 1.3.6.1.4.1.272.4.2.12.1.4 | ColumnisdnCreditsMaxInCon | read-write | mandatory | Maximum number of allowed incoming connections during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.272.4.2.12.1.5 | ColumnisdnCreditsMaxOutCon | read-write | mandatory | Maximum number of allowed outgoing connections during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.272.4.2.12.1.6 | ColumnisdnCreditsMaxCharge | read-write | mandatory | Maximum allowed charge amount during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.272.4.2.12.1.7 | ColumnisdnCreditsMaxInDuration | read-write | mandatory | Maximum connect time for incoming connections in seconds during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.272.4.2.12.1.8 | ColumnisdnCreditsMaxOutDuration | read-write | mandatory | Maximum connect time for outgoing connections in seconds during the observation interval. -1 disables this limit |
| 1.3.6.1.4.1.272.4.2.12.1.9 | ColumnisdnCreditsTimeleft | read-write | mandatory | Time in seconds left in current interval. Writing to Timeleft will restart the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.10 | ColumnisdnCreditsCurrentInCon | read-only | mandatory | Current number of incoming connections. |
| 1.3.6.1.4.1.272.4.2.12.1.11 | ColumnisdnCreditsCurrentOutCon | read-only | mandatory | Current number of outgoing connections. |
| 1.3.6.1.4.1.272.4.2.12.1.12 | ColumnisdnCreditsTotalInCon | read-only | mandatory | Total count of incoming connections during the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.13 | ColumnisdnCreditsTotalOutCon | read-only | mandatory | Total count of outgoing connections during the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.14 | ColumnisdnCreditsTotalMaxCon | read-only | mandatory | Maximum number of simultaniously established connections during the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.15 | ColumnisdnCreditsTotalCharge | read-only | mandatory | Total accounted charge during the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.16 | ColumnisdnCreditsTotalInDuration | read-only | mandatory | Total connect time of incoming connections during the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.17 | ColumnisdnCreditsTotalOutDuration | read-only | mandatory | Total connect time of outgoing connections during the observation interval. |
| 1.3.6.1.4.1.272.4.2.12.1.18 | ColumnisdnCreditsMaxCurrentInCon | read-write | mandatory | Maximum number of currently allowed incoming connections. -1 disables this limit. |
| 1.3.6.1.4.1.272.4.2.12.1.19 | ColumnisdnCreditsMaxCurrentOutCon | read-write | mandatory | Maximum number of currently allowed outgoing connections. -1 disables this limit. |
| 1.3.6.1.4.1.272.4.2.12.1.20 | ColumnisdnCreditsMaxCurrentCon | read-write | mandatory | Maximum number of currently allowed connections in both directions. -1 disables this limit. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Date | INTEGER | ||
| HexValue | INTEGER |