BIANCA-BRICK-IP-MIB
184 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3 | Nodeorg | |||
| 1.3.6 | Nodedod | |||
| 1.3.6.1 | Nodeinternet | |||
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.272 | Nodebintec | |||
| 1.3.6.1.4.1.272.4 | Nodebibo | |||
| 1.3.6.1.4.1.272.4.5 | Nodebiboip | |||
| 1.3.6.1.4.1.272.4.5.3 | TableipExtIfTable | not-accessible | mandatory | The ipExtIfTable contains extended information related to IP and the interfaces found on the system. Entries can only be added or deleted by the system. |
| 1.3.6.1.4.1.272.4.5.3.1 | RowipExtIfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.3.1.1 | ColumnipExtIfIndex | read-only | mandatory | Unique interface index |
| 1.3.6.1.4.1.272.4.5.3.1.3 | ColumnipExtIfRipSend | read-write | mandatory | specifies which versions of RIP messages are sent to that interface. Usually RIP messages are sent as broadcast, except this object is set to ripV2mcast. In th… |
| 1.3.6.1.4.1.272.4.5.3.1.4 | ColumnipExtIfRipReceive | read-write | mandatory | specifies which versions of RIP messages are accepted from that interface. RIP V2 messages are received regardless if they are sent as broadcast or multicast. |
| 1.3.6.1.4.1.272.4.5.3.1.5 | ColumnipExtIfProxyArp | read-write | mandatory | Switch for Proxy ARP on this interface. |
| 1.3.6.1.4.1.272.4.5.3.1.6 | ColumnipExtIfNat | read-write | mandatory | This object can be used to switch NAT on and off for a specific interface. |
| 1.3.6.1.4.1.272.4.5.3.1.7 | ColumnipExtIfNatRmvFin | read-write | mandatory | This object specifies, wether entries in the IpNatTable shall be removed, when TCP-FINS have been received and acknowledged in both directions, a TCP-RST has b… |
| 1.3.6.1.4.1.272.4.5.3.1.8 | ColumnipExtIfNatTcpTimeout | read-write | mandatory | TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds. |
| 1.3.6.1.4.1.272.4.5.3.1.9 | ColumnipExtIfNatOtherTimeout | read-write | mandatory | Non-TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds. |
| 1.3.6.1.4.1.272.4.5.3.1.10 | ColumnipExtIfNatOutXlat | read-write | mandatory | This object can be used to switch the outgoing address translation off. Then, all addresses are passed instead of being translated. The session mechanism remai… |
| 1.3.6.1.4.1.272.4.5.3.1.11 | ColumnipExtIfAccounting | read-write | mandatory | Switch for accounting on the specified interface. An IP packet is being accounted, when this object is set to on for either the source or the destination inter… |
| 1.3.6.1.4.1.272.4.5.3.1.12 | ColumnipExtIfTcpSpoofing | read-write | mandatory | Switch for TCP spoofing on this interface. TCP keepalive polls are answered by the BRICK to prevent unnecessary ISDN connections. Set this object to on for ISD… |
| 1.3.6.1.4.1.272.4.5.3.1.13 | ColumnipExtIfAccessAction | read-write | mandatory | This object describes the action, that is done, when a packet received from the interface has been filtered out. When set to ignore, no action takes place. Whe… |
| 1.3.6.1.4.1.272.4.5.3.1.14 | ColumnipExtIfAccessReport | read-write | mandatory | This object specifies, how a packed filtered by accesslists should be logged. When set to none, no logging takes place. When set to info, protocol, ip-addresse… |
| 1.3.6.1.4.1.272.4.5.3.1.15 | ColumnipExtIfOspf | read-write | mandatory | Configure the OSPF status of this interface. Routing information about routes on passive and active interfaces is propagated on active interfaces. Only active … |
| 1.3.6.1.4.1.272.4.5.3.1.16 | ColumnipExtIfOspfMetric | read-write | mandatory | Configure the metric calculation of OSPF interfaces. If set to auto the metric is calculated based on ifSpeed. If set to fixed the metric is taken from the osp… |
| 1.3.6.1.4.1.272.4.5.3.1.17 | ColumnipExtIfTcpCksum | read-write | mandatory | Enable or disable the TCP checksum check for local packets received on the corresponding interface. Disabling the check may improve performance for some local … |
| 1.3.6.1.4.1.272.4.5.3.1.18 | ColumnipExtIfBackRtVerify | read-write | mandatory | This object activates an additional check for incoming packets. If set to on, incoming packets are only accepted if return packets sent back to their source IP… |
| 1.3.6.1.4.1.272.4.5.3.1.19 | ColumnipExtIfRuleIndex | read-write | mandatory | This object defines the index of the first access rule that is applied for incoming packets. If set to 0 or if there is no access rule with this index no acces… |
| 1.3.6.1.4.1.272.4.5.3.1.20 | ColumnipExtIfAuthentication | read-write | mandatory | This object defines the authentication scheme used for incoming packets. |
| 1.3.6.1.4.1.272.4.5.3.1.21 | ColumnipExtIfAuthMode | read-write | mandatory | This object defines the authentication mode. If set to strict each source IP address must be authenticated. If set to loose all source IP addresses are allowed… |
| 1.3.6.1.4.1.272.4.5.3.1.22 | ColumnipExtIfAuthLifeTime | read-write | mandatory | This object defines the time in seconds a successful authentication is valid since the IP partner was authenticated. |
| 1.3.6.1.4.1.272.4.5.3.1.23 | ColumnipExtIfAuthKeepalive | read-write | mandatory | This object defines the period between short authentications that are invisible to the user |
| 1.3.6.1.4.1.272.4.5.3.1.24 | ColumnipExtIfRouteAnnounce | read-write | mandatory | This object defines the condition when routes on this interface are propagated by routing protocols. If set to up-only routes are only propagated if the operat… |
| 1.3.6.1.4.1.272.4.5.3.1.25 | ColumnipExtIfIpFragmentation | read-write | mandatory | This object defines different modes used for fragmentation of IP datagrams greater than the MTU of the destination interface. If set to enabled (1) each IP dat… |
| 1.3.6.1.4.1.272.4.5.3.1.26 | ColumnipExtIfRerouting | read-write | mandatory | This object enables or disables rerouting on this interface. The default value is enabled. If set to disabled, then only the better one route from two or more … |
| 1.3.6.1.4.1.272.4.5.3.1.27 | ColumnipExtIfBodRuleIndex | read-write | mandatory | This object defines the index of the first rule used for Bandwidth on Demand (BOD) that is applied for incoming and/or outgoing traffic. If set to 0 or if ther… |
| 1.3.6.1.4.1.272.4.5.3.1.28 | ColumnipExtIfQosRuleIndex | read-write | mandatory | This object defines the index of the first rule used for Qos (Qualtiy of Service) rules applied for IP traffic. If set to 0 or if there is no entry in the ipQo… |
| 1.3.6.1.4.1.272.4.5.3.1.29 | ColumnipExtIfIpsecAccounting | read-write | mandatory | This object determines, whether packets which are en- or decapsulated by IPSec should be accounted with encapsulation header(ipsec) or without the encapsulatio… |
| 1.3.6.1.4.1.272.4.5.3.1.30 | ColumnipExtIfMulticast | read-write | mandatory | Enable that multicast frames are accepted from that interface. |
| 1.3.6.1.4.1.272.4.5.3.1.31 | ColumnipExtIfNatSilentDeny | read-write | mandatory | This object specifies - if NAT is enabled (see ipExtIfNat) - wether incoming IP packets not passed by the NAT barrier should answered with an ICMP Host Unreach… |
| 1.3.6.1.4.1.272.4.5.4 | TableipExtRtTable | not-accessible | mandatory | The ipExtRtTable can be used in addition (not instead of) to the ipRouteTable to specify routing of IP datagrams. The selection of datagram-types is more speci… |
| 1.3.6.1.4.1.272.4.5.4.1 | RowipExtRtEntry | not-accessible | mandatory | Each entry in the ipExtRtTable describes a set of IP datagrams and the destination interface for that set. Metric parameters allow for ordering of the differen… |
| 1.3.6.1.4.1.272.4.5.4.1.1 | ColumnipExtRtProtocol | read-write | mandatory | This object specifies the value of the protocolfield in the ip header for all IP-datagrams belonging to the set. If this object is set to dont-verify, the valu… |
| 1.3.6.1.4.1.272.4.5.4.1.2 | ColumnipExtRtSrcIfIndex | read-write | mandatory | This object specifies the source index of the IP-datagrams. If this object has a value other than 0, only datagrams received over the interface with the approp… |
| 1.3.6.1.4.1.272.4.5.4.1.3 | ColumnipExtRtSrcAddr | read-write | mandatory | This object describes together with ipExtRtSrcMask the range of the source-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.4 | ColumnipExtRtSrcMask | read-write | mandatory | This object describes together with ipExtRtSrcAddr the range of the source-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.5 | ColumnipExtRtSrcPort | read-write | mandatory | This object describes together with ipExtRtSrcPortRange the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and i… |
| 1.3.6.1.4.1.272.4.5.4.1.6 | ColumnipExtRtSrcPortRange | read-write | mandatory | This object describes together with ipExtRtSrcPort the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and includ… |
| 1.3.6.1.4.1.272.4.5.4.1.7 | ColumnipExtRtDstAddr | read-write | mandatory | This object describes together with ipExtRtDstMask the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.8 | ColumnipExtRtDstMask | read-write | mandatory | This object describes together with ipExtRtDstAddr the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.9 | ColumnipExtRtDstPort | read-write | mandatory | This object describes together with ipExtRtDstPortRange the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and i… |
| 1.3.6.1.4.1.272.4.5.4.1.10 | ColumnipExtRtDstPortRange | read-write | mandatory | This object describes together with ipExtRtDstPort the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and includ… |
| 1.3.6.1.4.1.272.4.5.4.1.11 | ColumnipExtRtTos | read-write | mandatory | This object describes together with ipExtRtTosMask the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TO… |
| 1.3.6.1.4.1.272.4.5.4.1.12 | ColumnipExtRtTosMask | read-write | mandatory | This object describes together with ipExtRtTos the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS va… |
| 1.3.6.1.4.1.272.4.5.4.1.13 | ColumnipExtRtDstIfMode | read-write | mandatory | This object describes different behavior depending on the ifOperStatus of the destination interface: dialup-wait: The route matches, when the ifOperStatus of t… |
| 1.3.6.1.4.1.272.4.5.4.1.14 | ColumnipExtRtDstIfIndex | read-write | mandatory | This object specifies the destination interface for the IP-datagrams belonging to the set. If the value of this object is set to 0, the datagrams of the set ar… |
| 1.3.6.1.4.1.272.4.5.4.1.15 | ColumnipExtRtNextHop | read-write | mandatory | This object is used on point-to-multipoint interfaces with indirect routes (see ipExrRtType) to specify the IP-address of the gateway on the network, where the… |
| 1.3.6.1.4.1.272.4.5.4.1.16 | ColumnipExtRtType | read-write | mandatory | This object specifies, on point-to-multipoint interface wether the datagram shall be sent to the destination IP address in the IP datagram header (direct) or t… |
| 1.3.6.1.4.1.272.4.5.4.1.17 | ColumnipExtRtMetric1 | read-write | mandatory | This object is used to specify an order on the entries in the ipExtRtTable. If a datagram is matching multiple entries, the entry with the lowest value of ipEx… |
| 1.3.6.1.4.1.272.4.5.4.1.18 | ColumnipExtRtMetric2 | read-write | mandatory | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.19 | ColumnipExtRtMetric3 | read-write | mandatory | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.20 | ColumnipExtRtMetric4 | read-write | mandatory | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.21 | ColumnipExtRtMetric5 | read-write | mandatory | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.22 | ColumnipExtRtProto | read-write | mandatory | This object describes, how the route has been gained. This will normaly be netmgmt, because there is currently no routing protocol, that is able to handle exte… |
| 1.3.6.1.4.1.272.4.5.4.1.23 | ColumnipExtRtAge | read-write | mandatory | This object specifies the age of the route. |
| 1.3.6.1.4.1.272.4.5.5 | TableipNatTable | not-accessible | mandatory | If NAT is switched on for an interface, this table contains an entry for each session running over the interface. Table entries are creates by the system whene… |
| 1.3.6.1.4.1.272.4.5.5.1 | RowipNatEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.5.1.1 | ColumnipNatIfIndex | read-only | mandatory | This object specifies the interface, for which the session is monitored. |
| 1.3.6.1.4.1.272.4.5.5.1.2 | ColumnipNatProtocol | read-only | mandatory | This object specifies the protocol, the session is using. The value icmp specifies an icmp-echo (ping) session. ICMP error messages are processed by the approp… |
| 1.3.6.1.4.1.272.4.5.5.1.3 | ColumnipNatIntAddr | read-only | mandatory | This object specifies the internal local IP Address used for the session. The internal address is only visible to inside networks and is translated to the exte… |
| 1.3.6.1.4.1.272.4.5.5.1.4 | ColumnipNatIntPort | read-only | mandatory | This object specifies the internal local portnumber used for the session. The internal portnumber is only visible to inside networks and is translated to the e… |
| 1.3.6.1.4.1.272.4.5.5.1.5 | ColumnipNatExtAddr | read-only | mandatory | This object specifies the external local address used for the session. This address is visible outside only and will be translated to the internal address, whe… |
| 1.3.6.1.4.1.272.4.5.5.1.6 | ColumnipNatExtPort | read-only | mandatory | This object specifies the external local portnumber used for the session. This address is visible outside only and is translated to the internal portnumber, wh… |
| 1.3.6.1.4.1.272.4.5.5.1.7 | ColumnipNatRemoteAddr | read-only | mandatory | This object specifies the remote IP-address used for the session. This is an outside address. However, it is visible to outside networks and also to inside net… |
| 1.3.6.1.4.1.272.4.5.5.1.8 | ColumnipNatRemotePort | read-only | mandatory | This object specifies the remote portnumber used for the session. This is an outside portnumber. However, it is visible to outside networks and also to inside … |
| 1.3.6.1.4.1.272.4.5.5.1.9 | ColumnipNatDirection | read-only | mandatory | This object specifies, whether the session is incoming (from outside to inside) or outgoing (from inside to outside). |
| 1.3.6.1.4.1.272.4.5.5.1.10 | ColumnipNatAge | read-only | mandatory | This object specifies how long no packet has been transferred for the session and is used internally for timeout purposes. |
| 1.3.6.1.4.1.272.4.5.6 | TableipNatPresetTable | not-accessible | mandatory | This table specifies the IP addresses and port numbers for sessions requested from outside. If this table is empty and NAT is enabled, only packets for session… |
| 1.3.6.1.4.1.272.4.5.6.1 | RowipNatPresetEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.6.1.1 | ColumnipNatPrIfIndex | read-write | mandatory | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.6.1.2 | ColumnipNatPrProtocol | read-write | mandatory | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.6.1.3 | ColumnipNatPrRemoteAddr | read-write | mandatory | This object specifies together with ipNatPrRemoteMask the the set of IP addresses of remote hosts initiating the connection. The table entry will be valid for … |
| 1.3.6.1.4.1.272.4.5.6.1.4 | ColumnipNatPrRemoteMask | read-write | mandatory | This object specifies together with ipNatPrRemoteAddr the the set of IP addresses of remote hosts initiating the connection. The table entry will be valid for … |
| 1.3.6.1.4.1.272.4.5.6.1.5 | ColumnipNatPrExtAddr | read-write | mandatory | This object specifies together with ipNatPrExtMask the the set of called IP addresses, for which the table entry shall be valid. The entry is valid, if the cal… |
| 1.3.6.1.4.1.272.4.5.6.1.6 | ColumnipNatPrExtMask | read-write | mandatory | This object specifies together with ipNatPrExtAddr the the set of called IP addresses, for which the table entry shall be valid. The entry is valid, if the cal… |
| 1.3.6.1.4.1.272.4.5.6.1.7 | ColumnipNatPrExtPort | read-write | mandatory | This object specifies together with ipNatPrExtPortRange the range of portnumbers for incoming call, for which the table entry shall be valid. If both objects a… |
| 1.3.6.1.4.1.272.4.5.6.1.8 | ColumnipNatPrExtPortRange | read-write | mandatory | This object specifies together with ipNatPrExtPort the range of portnumbers for incoming call, for which the table entry shall be valid. If both objects are se… |
| 1.3.6.1.4.1.272.4.5.6.1.9 | ColumnipNatPrIntAddr | read-write | mandatory | This object specifies the internal target hosts IP address for incoming calls matching the table entry. An incoming call matching this entry will be routed to … |
| 1.3.6.1.4.1.272.4.5.6.1.10 | ColumnipNatPrIntPort | read-write | mandatory | This object specifies the internal target hosts port-number for incoming calls matching the table entry. If this object is set to -1, the target portnumber wil… |
| 1.3.6.1.4.1.272.4.5.7 | TableipSessionTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1 | RowipSessionEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.1 | ColumnipSessionSrcAddr | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.2 | ColumnipSessionSrcPort | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.3 | ColumnipSessionDstAddr | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.4 | ColumnipSessionDstPort | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.5 | ColumnipSessionOutPkts | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.6 | ColumnipSessionOutOctets | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.7 | ColumnipSessionInPkts | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.8 | ColumnipSessionInOctets | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.9 | ColumnipSessionProtocol | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.10 | ColumnipSessionAge | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.11 | ColumnipSessionIdle | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.12 | ColumnipSessionSrcIfIndex | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.7.1.13 | ColumnipSessionDstIfIndex | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.5.12 | TableipImportTable | not-accessible | mandatory | This table specifies how routes from one routing protocol are imported into another routing protocol. The dummy protocol default-route allows the generation of… |
| 1.3.6.1.4.1.272.4.5.12.1 | RowipImportEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.12.1.1 | ColumnipImportSrcProto | read-write | mandatory | This object describes the protocol that generated the route and inserted it into the routing table. |
| 1.3.6.1.4.1.272.4.5.12.1.2 | ColumnipImportDstProto | read-write | mandatory | This object describes the destination protocol into that the routes should be imported. |
| 1.3.6.1.4.1.272.4.5.12.1.3 | ColumnipImportMetric1 | read-write | mandatory | This object defines the metric in the context of the destination protocol the imported routes should get. If set to -1 these routes get a protocol specific def… |
| 1.3.6.1.4.1.272.4.5.12.1.4 | ColumnipImportType | read-write | mandatory | This object might define protocol specific properties of the imported routes in the context of the destination protocol. |
| 1.3.6.1.4.1.272.4.5.12.1.5 | ColumnipImportAddr | read-write | mandatory | This object specifies together with ipImportMask the range of IP addresses for which the table entry should be valid. The entry is valid if the destination IP … |
| 1.3.6.1.4.1.272.4.5.12.1.6 | ColumnipImportMask | read-write | mandatory | This object specifies together with ipImportAddr the range of IP addresses for which the table entry should be valid. The entry is valid if the destination IP … |
| 1.3.6.1.4.1.272.4.5.12.1.7 | ColumnipImportEffect | read-write | mandatory | This object defines the effect this row should have. If set to import, the importation from ipImportSrcProto to ipImportDstProto takes place. If set to doNotIm… |
| 1.3.6.1.4.1.272.4.5.12.1.8 | ColumnipImportIfIndex | read-write | mandatory | This object specifies the interface index of the interface for which the entry should be valid. If set to 0 it will be valid for all interfaces. |
| 1.3.6.1.4.1.272.4.5.13 | TableipPriorityTable | not-accessible | mandatory | This table defines the order, in which routes from different protocols are being used to determine the destination of an ip packet. The table will contain an e… |
| 1.3.6.1.4.1.272.4.5.13.1 | RowipPriorityEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.13.1.1 | ColumnipPriorityProto | read-only | mandatory | This object specifies the routig-protocol, for which the entry is valid. |
| 1.3.6.1.4.1.272.4.5.13.1.2 | ColumnipPriorityValue | read-write | mandatory | This object contains the priority-value for a specific routing protocol. Low values mean high precedence. |
| 1.3.6.1.4.1.272.4.5.15 | TableipFilterTable | not-accessible | mandatory | The ipFilterTable defines filters that describe subsets of IP packets. The filter matches if all conditions defined are true when comparing with the header of … |
| 1.3.6.1.4.1.272.4.5.15.1 | RowipFilterEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.15.1.1 | ColumnipFilterIndex | read-only | mandatory | This object uniquely references this filter. The index value is generated automatically. |
| 1.3.6.1.4.1.272.4.5.15.1.2 | ColumnipFilterDescr | read-write | mandatory | A textual string describing this filter. |
| 1.3.6.1.4.1.272.4.5.15.1.3 | ColumnipFilterProtocol | read-write | mandatory | This object specifies the value of the protocol field in the ip header for all IP-datagrams belonging to the set. If this object is set to dont-verify, the val… |
| 1.3.6.1.4.1.272.4.5.15.1.4 | ColumnipFilterSrcAddr | read-write | mandatory | This object specifies together with ipFilterSrcMask the set of IP addresses of datagrams that belong to the subset defined by this entry. If both objects are s… |
| 1.3.6.1.4.1.272.4.5.15.1.5 | ColumnipFilterSrcMask | read-write | mandatory | This object specifies together with ipFilterSrcAddr the set of IP addresses of datagrams that belong to the subset defined by this entry. If both objects are s… |
| 1.3.6.1.4.1.272.4.5.15.1.6 | ColumnipFilterSrcPort | read-write | mandatory | This object describes together with ipFilterSrcPortRange the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and … |
| 1.3.6.1.4.1.272.4.5.15.1.7 | ColumnipFilterSrcPortRange | read-write | mandatory | This object describes together with ipFilterDstPort the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and inclu… |
| 1.3.6.1.4.1.272.4.5.15.1.8 | ColumnipFilterDstAddr | read-write | mandatory | This object describes together with ipFilterDstMask the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.… |
| 1.3.6.1.4.1.272.4.5.15.1.9 | ColumnipFilterDstMask | read-write | mandatory | This object describes together with ipFilterDstAddr the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.… |
| 1.3.6.1.4.1.272.4.5.15.1.10 | ColumnipFilterDstPort | read-write | mandatory | This object describes together with ipFilterDstPortRange the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and … |
| 1.3.6.1.4.1.272.4.5.15.1.11 | ColumnipFilterDstPortRange | read-write | mandatory | This object describes together with ipFilterDstPort the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and inclu… |
| 1.3.6.1.4.1.272.4.5.15.1.12 | ColumnipFilterTcpConnState | read-write | mandatory | This object describes the state of the TCP connection associated with the packets belonging to the set. If this object is set to established, the value of the … |
| 1.3.6.1.4.1.272.4.5.15.1.13 | ColumnipFilterIcmpType | read-write | mandatory | This object describes the ICMP type of the packets belonging to the set. If this object is set to dont-verify, the value of the ICMP type field is not specifie… |
| 1.3.6.1.4.1.272.4.5.15.1.14 | ColumnipFilterTos | read-write | mandatory | This object describes together with ipFilterTosMask the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A T… |
| 1.3.6.1.4.1.272.4.5.15.1.15 | ColumnipFilterTosMask | read-write | mandatory | This object describes together with ipFilterTos the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS v… |
| 1.3.6.1.4.1.272.4.5.16 | TableipRuleTable | not-accessible | mandatory | The ipRuleTable defines access rules for checking incoming IP packets. The rules are processed in order, i.e. each rule has a link to the next rule. The set of… |
| 1.3.6.1.4.1.272.4.5.16.1 | RowipRuleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.16.1.1 | ColumnipRuleIndex | read-only | mandatory | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.16.1.2 | ColumnipRuleFilterIndex | read-write | mandatory | References the rule's associated filter. |
| 1.3.6.1.4.1.272.4.5.16.1.3 | ColumnipRuleAction | read-write | mandatory | This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is pro… |
| 1.3.6.1.4.1.272.4.5.16.1.4 | ColumnipRuleNextRuleIndex | read-write | mandatory | Specifies the next rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.18 | TableipNatOutTable | not-accessible | mandatory | This table specifies the IP address translation for outgoing sessions. If no matching entry is found the IP address is set to the IP address defined on the int… |
| 1.3.6.1.4.1.272.4.5.18.1 | RowipNatOutEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.18.1.1 | ColumnipNatOutIfIndex | read-write | mandatory | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.18.1.2 | ColumnipNatOutProtocol | read-write | mandatory | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.18.1.3 | ColumnipNatOutRemoteAddr | read-write | mandatory | This object specifies together with ipNatOutRemoteMask the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, t… |
| 1.3.6.1.4.1.272.4.5.18.1.4 | ColumnipNatOutRemoteMask | read-write | mandatory | This object specifies together with ipNatOutRemoteAddr the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, t… |
| 1.3.6.1.4.1.272.4.5.18.1.5 | ColumnipNatOutExtAddr | read-write | mandatory | This object specifies the external IP address to which the internal IP address is mapped. |
| 1.3.6.1.4.1.272.4.5.18.1.6 | ColumnipNatOutRemotePort | read-write | mandatory | This object specifies together with ipNatOutRemotePortRange the range of portnumbers for outgoing calls, for which the table entry shall be valid. If both obje… |
| 1.3.6.1.4.1.272.4.5.18.1.7 | ColumnipNatOutRemotePortRange | read-write | mandatory | This object specifies together with ipNatOutRemotePort the range of portnumbers for outgoing calls, for which the table entry shall be valid. If both objects a… |
| 1.3.6.1.4.1.272.4.5.18.1.8 | ColumnipNatOutIntAddr | read-write | mandatory | This object specifies together with ipNatOutIntMask the internal hosts IP address for outgoing calls matching the table entry. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.18.1.9 | ColumnipNatOutIntMask | read-write | mandatory | This object specifies together with ipNatOutIntAddr the internal hosts IP address for outgoing calls matching the table entry. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.18.1.10 | ColumnipNatOutIntPort | read-write | mandatory | This object specifies the internal source port for which the table entry shall be valid. If this object is set to -1, any internal source port matches this ent… |
| 1.3.6.1.4.1.272.4.5.18.1.11 | ColumnipNatOutExtPort | read-write | mandatory | This object may be used to specify a fixed external source port to which the internal source port is mapped. If this object is set to -1, the port is mapped to… |
| 1.3.6.1.4.1.272.4.5.19 | TableipHostsAliveTable | not-accessible | mandatory | This table specifies the watched IP addresses. Entries in the table are created and removed manually by network management. |
| 1.3.6.1.4.1.272.4.5.19.1 | RowipHostsAliveEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.19.1.1 | ColumnipHostsAliveGroup | read-write | mandatory | The group of the watched IP-Addresses |
| 1.3.6.1.4.1.272.4.5.19.1.2 | ColumnipHostsAliveIPAddress | read-write | mandatory | The watched IP-Address |
| 1.3.6.1.4.1.272.4.5.19.1.3 | ColumnipHostsAliveState | read-only | mandatory | The State of the watched IP-Address |
| 1.3.6.1.4.1.272.4.5.19.1.4 | ColumnipHostsAliveInterval | read-write | mandatory | This is the timeinterval for state verification |
| 1.3.6.1.4.1.272.4.5.19.1.5 | ColumnipHostsAliveDownAction | read-write | mandatory | This action must be perform, if the hosts do not answer |
| 1.3.6.1.4.1.272.4.5.19.1.6 | ColumnipHostsAliveFirstIfIndex | read-write | mandatory | The first ifc |
| 1.3.6.1.4.1.272.4.5.19.1.7 | ColumnipHostsAliveRange | read-write | mandatory | The range of all ifc�s |
| 1.3.6.1.4.1.272.4.5.21 | TableipBodRuleTable | not-accessible | mandatory | The ipBodRuleTable defines access rules for checking incoming IP packets. The rules are processed in order, i.e. each rule has a link to the next rule. The set… |
| 1.3.6.1.4.1.272.4.5.21.1 | RowipBodRuleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.21.1.1 | ColumnipBodRuleIndex | read-only | mandatory | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.21.1.2 | ColumnipBodRuleFilterIndex | read-write | mandatory | References the rule's associated filter. |
| 1.3.6.1.4.1.272.4.5.21.1.3 | ColumnipBodRuleAction | read-write | mandatory | This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is pro… |
| 1.3.6.1.4.1.272.4.5.21.1.4 | ColumnipBodRuleDirection | read-write | mandatory | This object specifies the direction of the packets for which the rule is processed. |
| 1.3.6.1.4.1.272.4.5.21.1.5 | ColumnipBodRuleChannels | read-write | mandatory | The number of B-channels to invoke if the rule's associated filter matches. |
| 1.3.6.1.4.1.272.4.5.21.1.6 | ColumnipBodRuleNextRuleIndex | read-write | mandatory | Specifies the next rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.21.1.7 | ColumnipBodRuleIdleTime | read-write | mandatory | Specifies the time in seconds the interface-specific shorthold interval (see biboPPPTable) is extended if the rule's associated filter matches. When set to zer… |
| 1.3.6.1.4.1.272.4.5.22 | TableipQoSTable | not-accessible | mandatory | The ipQosTable defines the classifier rules that are applied to IP traffic arriving this interface in a particular direction. The rules are processed in order,… |
| 1.3.6.1.4.1.272.4.5.22.1 | RowipQoSEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.22.1.1 | ColumnipQoSIndex | read-only | mandatory | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.22.1.2 | ColumnipQoSFilterIndex | read-write | mandatory | References the associated filter (see IpFilterTable). |
| 1.3.6.1.4.1.272.4.5.22.1.3 | ColumnipQoSNextRuleIndex | read-write | mandatory | Specifies the next classifier rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.22.1.4 | ColumnipQoSAction | read-write | mandatory | This object specifies the action to be performed if the associated filter matches. If set to ignore the filter is not consulted and the next rule is processed … |
| 1.3.6.1.4.1.272.4.5.22.1.5 | ColumnipQoSTos | read-write | mandatory | Value for TOS field inside IP header to be set. |
| 1.3.6.1.4.1.272.4.5.22.1.7 | ColumnipQoSTosSetRate | read-write | mandatory | Maximum amount of packets per second that should be TOS changed. |
| 1.3.6.1.4.1.272.4.5.22.1.8 | ColumnipQoSTosSetBurst | read-write | mandatory | Maximum amount of packets per second additional to the ipQosSetRate that could be TOS changed. |
| 1.3.6.1.4.1.272.4.5.22.1.11 | ColumnipQoSServiceClass | read-write | mandatory | This object specifies together with ipQoSClassId the class of service used for the congestion management, priorization and traffic shapping. If set to high-pri… |
| 1.3.6.1.4.1.272.4.5.22.1.12 | ColumnipQoSClassId | read-write | mandatory | This object specifies together with ipQoSServiceClass (normal(1) only) the class of service used for congestion avoidance, congestion management, priorization … |
| 1.3.6.1.4.1.272.4.5.22.1.13 | ColumnipQoSDirection | read-write | mandatory | This object specifies the direction for witch this classifier rule applies on this interface, possible values: outgoing(1) = used for outgoing packets only inc… |