BKTEL-HFC862-OVTX-V11-MIB
216 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.7501.1.2.101 | Nodeovtx | |||
| 1.3.6.1.4.1.7501.1.2.101.1 | NodeovtxCommon | |||
| 1.3.6.1.4.1.7501.1.2.101.1.1 | ScalarovtxCommonNumberOfModules | read-only | mandatory | Number of modules in table. |
| 1.3.6.1.4.1.7501.1.2.101.1.2 | TableovtxCommonTable | not-accessible | mandatory | The table contains all modules of the OVTX-type in the NE |
| 1.3.6.1.4.1.7501.1.2.101.1.2.1 | RowovtxCommonEntry | not-accessible | mandatory | Common-Values for a module. |
| 1.3.6.1.4.1.7501.1.2.101.1.2.1.1 | ColumnovtxNESlot | read-only | mandatory | The slot number of the chassis for which this entry contains management information. Equal to: modOVTXv11UniqueID |
| 1.3.6.1.4.1.7501.1.2.101.1.2.1.2 | ColumnovtxCommonType | read-only | mandatory | The type of physical module. modSlotEmpty indicates an empty slot. A Value of modSlotUnknown indicates that the type of module is unknown. |
| 1.3.6.1.4.1.7501.1.2.101.1.2.1.3 | ColumnovtxCommonDescr | read-write | mandatory | A textual description of the module. If not available, this Value should be set to a zero length string. |
| 1.3.6.1.4.1.7501.1.2.101.1.2.1.4 | ColumnovtxCommonFirmwareId | read-only | mandatory | The firmware Id of the module. |
| 1.3.6.1.4.1.7501.1.2.101.1.2.1.5 | ColumnovtxCommonModuleWidth | read-only | optional | The width of the module in multiples of slots (1, 2, ...) |
| 1.3.6.1.4.1.7501.1.2.101.2 | NodeovtxStates | |||
| 1.3.6.1.4.1.7501.1.2.101.2.1 | TableovtxStatesTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1 | RowovtxStatesEntry | not-accessible | mandatory | Alarms for a module. |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.1 | ColumnovtxStatesOutputLow | read-only | mandatory | Optical output power low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.2 | ColumnovtxStatesOutputHigh | read-only | mandatory | Optical output power high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.3 | ColumnovtxStatesInputLow | read-only | mandatory | RF input power low (CATV input) |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.4 | ColumnovtxStatesLaserAging | read-only | mandatory | The laser is aging |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.5 | ColumnovtxStatesTecHigh | read-only | mandatory | Laser cooler limit reached |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.6 | ColumnovtxStatesLaserTempLow | read-only | mandatory | Laser temperature low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.7 | ColumnovtxStatesLaserTempHigh | read-only | mandatory | Laser temperature high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.8 | ColumnovtxStatesOmiOrRfgainLow | read-only | mandatory | Omi or rf-gain (depending on mode) low (CATV input) |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.9 | ColumnovtxStatesOmiOrRfgainHigh | read-only | mandatory | Omi or rf-gain (depending on mode) high (CATV input) |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.10 | ColumnovtxStatesPowerSupplyLeft | read-only | mandatory | The left (looking from front) power supply unit fails |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.11 | ColumnovtxStatesPowerSupplyRight | read-only | mandatory | The right (looking from front) power supply unit fails |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.12 | ColumnovtxStatesFanLeft | read-only | mandatory | The left (looking from front) fan unit fails |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.13 | ColumnovtxStatesFanRight | read-only | mandatory | The right (looking from front) fan unit fails |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.14 | ColumnovtxStatesTemperatureLow | read-only | mandatory | Device internal temperature low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.15 | ColumnovtxStatesTemperatureHigh | read-only | mandatory | Device internal temperature high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.16 | ColumnovtxStatesPlus3p3VLow | read-only | mandatory | 3.3 Volt supply low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.17 | ColumnovtxStatesPlus3p3VHigh | read-only | mandatory | 3.3 Volt supply high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.18 | ColumnovtxStatesPlus5VLow | read-only | mandatory | 5 Volt supply low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.19 | ColumnovtxStatesPlus5VHigh | read-only | mandatory | 5 Volt supply high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.20 | ColumnovtxStatesPlus12VLow | read-only | mandatory | 12 Volt supply low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.21 | ColumnovtxStatesPlus12VHigh | read-only | mandatory | 12 Volt supply high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.22 | ColumnovtxStatesPlus24VLow | read-only | mandatory | 24 Volt supply low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.23 | ColumnovtxStatesPlus24VHigh | read-only | mandatory | 24 Volt supply high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.24 | ColumnovtxStatesMinus5VLow | read-only | mandatory | -5 Volt supply low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.25 | ColumnovtxStatesMinus5VHigh | read-only | mandatory | -5 Volt supply high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.26 | ColumnovtxStatesMinus12VLow | read-only | mandatory | -12 Volt supply low |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.27 | ColumnovtxStatesMinus12VHigh | read-only | mandatory | -12 Volt supply high |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.28 | ColumnovtxStatesLaserShutdown | read-only | mandatory | Laser is shutdown, no optical output |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.29 | ColumnovtxStatesInitializing | read-only | mandatory | The device is initializing |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.30 | ColumnovtxStatesBootloader | read-only | mandatory | The device is running in bootloader mode without a legal application software. |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.31 | ColumnovtxStatesCommLoss | read-only | mandatory | The NEC has lost the connection to the device. Reason may be a removed or defective device. Note that this state is set by the NEC and not by the device |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.32 | ColumnovtxStatesInputHigh | read-only | mandatory | RF input power high (CATV input) |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.33 | ColumnovtxStatesRedundancySwitch | read-only | mandatory | This (redundant) device has been activated (redundancy switchover) |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.34 | ColumnovtxStatesSatInputLow | read-only | mandatory | RF input power low (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.35 | ColumnovtxStatesSatInputHigh | read-only | mandatory | RF input power high (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.36 | ColumnovtxStatesSatOmiOrRfgainLow | read-only | mandatory | Omi or rf-gain (depending on mode) low (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5… |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.37 | ColumnovtxStatesSatOmiOrRfgainHigh | read-only | mandatory | Omi or rf-gain (depending on mode) high (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(… |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.38 | ColumnovtxStatesSatLnbShortCircuit | read-only | mandatory | Short-circuit at SAT LNB Only used if ovtxDisplaySatLnbSupplySupported != notSupported(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.39 | ColumnovtxStatesSbs1Level | read-only | mandatory | SBS #1 level alarm Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.40 | ColumnovtxStatesSbs2Level | read-only | mandatory | SBS #2 level alarm Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.41 | ColumnovtxStatesSbs1PllNotLocked | read-only | mandatory | SBS #1 PLL not locked Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.42 | ColumnovtxStatesSbs2PllNotLocked | read-only | mandatory | SBS #2 PLL not locked Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). |
| 1.3.6.1.4.1.7501.1.2.101.2.1.1.43 | ColumnovtxStatesInternalAlarm | read-only | mandatory | Internal hardware failure |
| 1.3.6.1.4.1.7501.1.2.101.3 | NodeovtxConfiguration | |||
| 1.3.6.1.4.1.7501.1.2.101.3.1 | TableovtxConfigurationTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1 | RowovtxConfigurationEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.1 | ColumnovtxConfigurationNESlotWrite | read-write | optional | By writing this variable a slot can be assigned for devices that dont support hardware slot detection. Reading '-1' means that the slot position is NOT writabl… |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.2 | ColumnovtxConfigurationModeAGC | read-write | mandatory | The AGC mode of the optical transmitter (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.3 | ColumnovtxConfigurationOmi | read-write | mandatory | The desired offset from nominal OMI in 0.1dB units (CATV input). This parameter is only used if AGC is on. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.4 | ColumnovtxConfigurationRfGain | read-write | mandatory | The desired offset from nominal gain in 0.1dB units (CATV input). This parameter is only used if AGC is off. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.5 | ColumnovtxConfigurationSbsSuppression | read-write | mandatory | The sbs suppression in 0.1dBm units. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.6 | ColumnovtxConfigurationChannelDistance | read-write | mandatory | The channel raster in MHz units. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.7 | ColumnovtxConfigurationLaserFrequency | read-write | mandatory | The laser frequency in GHz units. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.8 | ColumnovtxConfigurationRfInputLimitLoLo | read-write | mandatory | The rf input power low alarm limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.9 | ColumnovtxConfigurationRfInputLimitLo | read-write | mandatory | The rf input power low warning limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.10 | ColumnovtxConfigurationRfInputLimitHi | read-write | mandatory | The rf input power high warning limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.11 | ColumnovtxConfigurationRfInputLimitHiHi | read-write | mandatory | The rf input power high alarm limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.12 | ColumnovtxConfigurationRfGainMeasuredLimitLoLo | read-write | mandatory | The Measured-Rf-Gain offset low alarm limit in 0.1 dB units (in AGC ON mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.13 | ColumnovtxConfigurationRfGainMeasuredLimitLo | read-write | mandatory | The Measured-Rf-Gain offset low warning limit in 0.1 dB units (in AGC ON mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.14 | ColumnovtxConfigurationRfGainMeasuredLimitHi | read-write | mandatory | The Measured-Rf-Gain offset high warning limit in 0.1 dB units (in AGC ON mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.15 | ColumnovtxConfigurationRfGainMeasuredLimitHiHi | read-write | mandatory | The Measured-Rf-Gain offset high alarm limit in 0.1 dB units (in AGC ON mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.16 | ColumnovtxConfigurationOmiMeasuredLimitLoLo | read-write | mandatory | The Measured-OMI offset low alarm limit in 0.1 dB units (in AGC OFF mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.17 | ColumnovtxConfigurationOmiMeasuredLimitLo | read-write | mandatory | The Measured-OMI offset low warning limit in 0.1 dB units(in AGC OFF mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.18 | ColumnovtxConfigurationOmiMeasuredLimitHi | read-write | mandatory | The Measured-OMI offset high warning limit in 0.1 dB units(in AGC OFF mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.19 | ColumnovtxConfigurationOmiMeasuredLimitHiHi | read-write | mandatory | The Measured-OMI offset high alarm limit in 0.1 dB units(in AGC OFF mode) |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.20 | ColumnovtxConfigurationOutputPwrLimitLoLo | read-write | mandatory | The output power low alarm limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.21 | ColumnovtxConfigurationOutputPwrLimitLo | read-write | mandatory | The output power low warning limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.22 | ColumnovtxConfigurationOutputPwrLimitHi | read-write | mandatory | The output power high warning limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.23 | ColumnovtxConfigurationOutputPwrLimitHiHi | read-write | mandatory | The output power high alarm limit in 0.1 dBm units |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.24 | ColumnovtxConfigurationRedundancyMode | read-write | mandatory | The device's redundancy mode. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.25 | ColumnovtxConfigurationRedundancyMask | read-write | mandatory | The device's redundancy mask setings. |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.26 | ColumnovtxConfigurationCsoRegulationMode | read-write | mandatory | The desired CSO regulation mode of the optical transmitter. Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports csoRegModeChann… |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.27 | ColumnovtxConfigurationSlope | read-write | mandatory | The desired slope in 0.1 dB units (CATV input). Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports zero |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.28 | ColumnovtxConfigurationFiberLength | read-write | mandatory | The optical fiber length in meter units. Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports zero |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.29 | ColumnovtxConfigurationSatModeAGC | read-write | mandatory | The AGC mode of the optical transmitter (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports sat… |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.30 | ColumnovtxConfigurationSatOmi | read-write | mandatory | The desired offset from nominal OMI in 0.1dB units (SAT input). This parameter is only used if AGC is on. Only usable if ovtxDisplayRfInputCapabilities != rfIn… |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.31 | ColumnovtxConfigurationSatRfGain | read-write | mandatory | The desired offset from nominal gain in 0.1dB units (SAT input). This parameter is only used if AGC is off. Only usable if ovtxDisplayRfInputCapabilities != rf… |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.32 | ColumnovtxConfigurationSatSlope | read-write | mandatory | The desired slope in 0.1 dB units (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.33 | ColumnovtxConfigurationRfInputAlarmMode | read-write | mandatory | The RF input alarm mode (Can be used to disable alarms of unused RF inputs) Only usable if ovtxDisplayRfInputCapabilities == rfInputCatvAndSatSupported(3), oth… |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.34 | ColumnovtxConfigurationSatLnbSupply | read-write | mandatory | SAT LNB supply control. This feature is not supported by all transmitter devices, see ovtxDisplaySatLnbSupplySupported |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.35 | ColumnovtxConfigurationSbsSuppressionMode | read-write | mandatory | SBS suppression mode. This feature is not supported by all transmitter devices, see ovtxDisplaySbsSuppressionModeSupported |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.36 | ColumnovtxConfigurationSbsFiberType | read-write | mandatory | SBS fiber type. This feature is not supported by all transmitter devices, see ovtxDisplaySbsFiberParametersSupported |
| 1.3.6.1.4.1.7501.1.2.101.3.1.1.37 | ColumnovtxConfigurationSbsFiberLength | read-write | mandatory | SBS suppression mode. This feature is not supported by all transmitter devices, see ovtxDisplaySbsFiberParametersSupported |
| 1.3.6.1.4.1.7501.1.2.101.4 | NodeovtxControl | |||
| 1.3.6.1.4.1.7501.1.2.101.4.1 | TableovtxControlTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.4.1.1 | RowovtxControlEntry | not-accessible | mandatory | Alarms for a module. |
| 1.3.6.1.4.1.7501.1.2.101.4.1.1.1 | ColumnovtxControlLaserOutputMode | read-write | mandatory | The output mode of the laser. NOTE: The error mask used for parameter 'laserShutdownOnMaskedError(3)' is the same mask used for external IO port, 'ovtxConfigur… |
| 1.3.6.1.4.1.7501.1.2.101.4.1.1.2 | ColumnovtxControlReset | read-write | mandatory | Reset the module. |
| 1.3.6.1.4.1.7501.1.2.101.4.1.1.3 | ColumnovtxControlModuleLedBlink | read-write | mandatory | Writing this variable to true(1) lets the device's modul LED blink green for 10 seconds. Writing this variable to false(2) stops blinking at once. This variabl… |
| 1.3.6.1.4.1.7501.1.2.101.5 | NodeovtxMeasuringValues | |||
| 1.3.6.1.4.1.7501.1.2.101.5.1 | TableovtxMeasuringValuesTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1 | RowovtxMeasuringValuesEntry | not-accessible | mandatory | Common-Values for a module. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.1 | ColumnovtxOmiMeasuredLoLo | read-write | mandatory | Measured-OMI offset low alarm threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.2 | ColumnovtxOmiMeasuredLo | read-write | mandatory | Measured-OMI offset low warning threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.3 | ColumnovtxOmiMeasuredValue | read-only | mandatory | The offset from nominal OMI in steps of 0.1dB (CATV input). If AGC is on this parameter is equal to ovtxConfigurationOmi. If AGC is off this paramters shows th… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.4 | ColumnovtxOmiMeasuredHi | read-write | mandatory | Measured-OMI offset high warning threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.5 | ColumnovtxOmiMeasuredHiHi | read-write | mandatory | Measured-OMI offset high alarm threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.6 | ColumnovtxRfGainMeasuredLoLo | read-write | mandatory | Measured-Rf-Gain offset low alarm threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.7 | ColumnovtxRfGainMeasuredLo | read-write | mandatory | Measured-Rf-Gain offset low warning threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.8 | ColumnovtxRfGainMeasuredValue | read-only | mandatory | The offset from nominal gain in steps of 0.1dB (CATV input). If AGC is off this parameter is equal to ovtxConfigurationRfGain. If AGC is on this paramters show… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.9 | ColumnovtxRfGainMeasuredHi | read-write | mandatory | Measured-Rf-Gain offset high warning threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.10 | ColumnovtxRfGainMeasuredHiHi | read-write | mandatory | Measured-Rf-Gain offset high alarm threshold in steps of 0.1dB (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.11 | ColumnovtxLaserCurrentRelLoLo | read-only | mandatory | Relative laser current low alarm threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.12 | ColumnovtxLaserCurrentRelLo | read-only | mandatory | Relative laser current low warning threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.13 | ColumnovtxLaserCurrentRelValue | read-only | mandatory | The laser current relative to the current at begin of life in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.14 | ColumnovtxLaserCurrentRelHi | read-only | mandatory | Relative laser current high warning threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.15 | ColumnovtxLaserCurrentRelHiHi | read-only | mandatory | Relative laser current high alarm threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.16 | ColumnovtxTecCurrentRelLoLo | read-only | mandatory | Thermo-electric-cooler current low alarm threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.17 | ColumnovtxTecCurrentRelLo | read-only | mandatory | Thermo-electric-cooler current low warning threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.18 | ColumnovtxTecCurrentRelValue | read-only | mandatory | The thermo-electric-cooler current relative to its absolute high alarm threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.19 | ColumnovtxTecCurrentRelHi | read-only | mandatory | Thermo-electric-cooler current high warning threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.20 | ColumnovtxTecCurrentRelHiHi | read-only | mandatory | Thermo-electric-cooler current high alarm threshold in steps of 0.1%. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.21 | ColumnovtxOutputPowerLoLo | read-write | mandatory | Output power low alarm threshold in steps of 0.1dBm. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.22 | ColumnovtxOutputPowerLo | read-write | mandatory | Output power low warning threshold in steps of 0.1dBm. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.23 | ColumnovtxOutputPowerValue | read-only | mandatory | Output power in steps of 0.1dBm. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.24 | ColumnovtxOutputPowerHi | read-write | mandatory | Output power high warning threshold in steps of 0.1dBm. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.25 | ColumnovtxOutputPowerHiHi | read-write | mandatory | Output power high alarm threshold in steps of 0.1dBm. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.26 | ColumnovtxPlus3p3VLoLo | read-only | mandatory | The +3.3V supply voltage low alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.27 | ColumnovtxPlus3p3VLo | read-only | mandatory | The +3.3V supply voltage low warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.28 | ColumnovtxPlus3p3VValue | read-only | mandatory | The +3.3V supply voltage in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.29 | ColumnovtxPlus3p3VHi | read-only | mandatory | The +3.3V supply voltage high warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.30 | ColumnovtxPlus3p3VHiHi | read-only | mandatory | The +3.3V supply voltage high alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.31 | ColumnovtxPlus5VLoLo | read-only | mandatory | The +5V supply voltage low alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.32 | ColumnovtxPlus5VLo | read-only | mandatory | The +5V supply voltage low warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.33 | ColumnovtxPlus5VValue | read-only | mandatory | The +5V supply voltage in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.34 | ColumnovtxPlus5VHi | read-only | mandatory | The +5V supply voltage high warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.35 | ColumnovtxPlus5VHiHi | read-only | mandatory | The +5V supply voltage high alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.36 | ColumnovtxPlus12VLoLo | read-only | mandatory | The +12V supply voltage low alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.37 | ColumnovtxPlus12VLo | read-only | mandatory | The +12V supply voltage low warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.38 | ColumnovtxPlus12VValue | read-only | mandatory | The +12V supply voltage in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.39 | ColumnovtxPlus12VHi | read-only | mandatory | The +12V supply voltage high warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.40 | ColumnovtxPlus12VHiHi | read-only | mandatory | The +12V supply voltage high alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.41 | ColumnovtxPlus24VLoLo | read-only | mandatory | The +24V supply voltage low alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.42 | ColumnovtxPlus24VLo | read-only | mandatory | The +24V supply voltage low warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.43 | ColumnovtxPlus24VValue | read-only | mandatory | The +24V supply voltage in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.44 | ColumnovtxPlus24VHi | read-only | mandatory | The +24V supply voltage high warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.45 | ColumnovtxPlus24VHiHi | read-only | mandatory | The +24V supply voltage high alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.46 | ColumnovtxMinus5VLoLo | read-only | mandatory | The -5V supply voltage low alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.47 | ColumnovtxMinus5VLo | read-only | mandatory | The -5V supply voltage low warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.48 | ColumnovtxMinus5VValue | read-only | mandatory | The -5V supply voltage in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.49 | ColumnovtxMinus5VHi | read-only | mandatory | The -5V supply voltage high warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.50 | ColumnovtxMinus5VHiHi | read-only | mandatory | The -5V supply voltage high alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.51 | ColumnovtxMinus12VLoLo | read-only | mandatory | The -12V supply voltage low alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.52 | ColumnovtxMinus12VLo | read-only | mandatory | The -12V supply voltage low warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.53 | ColumnovtxMinus12VValue | read-only | mandatory | The -12V supply voltage in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.54 | ColumnovtxMinus12VHi | read-only | mandatory | The -12V supply voltage high warning threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.55 | ColumnovtxMinus12VHiHi | read-only | mandatory | The -12V supply voltage high alarm threshold in steps of 0.1V. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.56 | ColumnovtxTemperatureLoLo | read-only | mandatory | The module temperature low alarm threshold in steps of 0.1 celsius degrees. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.57 | ColumnovtxTemperatureLo | read-only | mandatory | The module temperature low warning threshold in steps of 0.1 celsius degrees. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.58 | ColumnovtxTemperatureValue | read-only | mandatory | The module temperature in steps of 0.1 celsius degrees. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.59 | ColumnovtxTemperatureHi | read-only | mandatory | The module temperature high warning threshold in steps of 0.1 celsius degrees. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.60 | ColumnovtxTemperatureHiHi | read-only | mandatory | The module temperature high alarm threshold in steps of 0.1 celsius degrees. |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.61 | ColumnovtxRfInputLoLo | read-write | mandatory | RfInput (total rms) low alarm threshold in steps of 0.1 dBm (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.62 | ColumnovtxRfInputLo | read-write | mandatory | RfInput (total rms) low warning threshold in steps of 0.1 dBm (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.63 | ColumnovtxRfInputValue | read-only | mandatory | RfInput (total rms) in steps of 0.1 dBm (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.64 | ColumnovtxRfInputHi | read-write | mandatory | RfInput (total rms) high warning threshold in steps of 0.1 dBm (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.65 | ColumnovtxRfInputHiHi | read-write | mandatory | RfInput (total rms) high alarm threshold in steps of 0.1 dBm (CATV input). |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.66 | ColumnovtxSatRfInputLoLo | read-write | mandatory | RfInput (total rms) low alarm threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwis… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.67 | ColumnovtxSatRfInputLo | read-write | mandatory | RfInput (total rms) low warning threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherw… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.68 | ColumnovtxSatRfInputValue | read-only | mandatory | RfInput (total rms) in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zer… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.69 | ColumnovtxSatRfInputHi | read-write | mandatory | RfInput (total rms) high warning threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), other… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.70 | ColumnovtxSatRfInputHiHi | read-write | mandatory | RfInput (total rms) high alarm threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwi… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.71 | ColumnovtxSatOmiMeasuredLoLo | read-write | mandatory | Measured-OMI offset low alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise … |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.72 | ColumnovtxSatOmiMeasuredLo | read-write | mandatory | Measured-OMI offset low warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwis… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.73 | ColumnovtxSatOmiMeasuredValue | read-only | mandatory | The offset from nominal OMI in steps of 0.1dB (SAT input). If SAT AGC is on this parameter is equal to ovtxConfigurationSatOmi. If SAT AGC is off this paramter… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.74 | ColumnovtxSatOmiMeasuredHi | read-write | mandatory | Measured-OMI offset high warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwi… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.75 | ColumnovtxSatOmiMeasuredHiHi | read-write | mandatory | Measured-OMI offset high alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.76 | ColumnovtxSatRfGainMeasuredLoLo | read-write | mandatory | Measured-Rf-Gain offset low alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherw… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.77 | ColumnovtxSatRfGainMeasuredLo | read-write | mandatory | Measured-Rf-Gain offset low warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), othe… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.78 | ColumnovtxSatRfGainMeasuredValue | read-only | mandatory | The offset from nominal gain in steps of 0.1dB (SAT input). If AGC is off this parameter is equal to ovtxConfigurationSatRfGain. If AGC is on this paramters sh… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.79 | ColumnovtxSatRfGainMeasuredHi | read-write | mandatory | Measured-Rf-Gain offset high warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), oth… |
| 1.3.6.1.4.1.7501.1.2.101.5.1.1.80 | ColumnovtxSatRfGainMeasuredHiHi | read-write | mandatory | Measured-Rf-Gain offset high alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), other… |
| 1.3.6.1.4.1.7501.1.2.101.6 | NodeovtxDisplay | |||
| 1.3.6.1.4.1.7501.1.2.101.6.1 | TableovtxDisplayTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1 | RowovtxDisplayEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.1 | ColumnovtxDisplayRfInputValue | read-only | mandatory | RfInput (total rms) in steps of 0.1 dBm. |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.2 | ColumnovtxDisplayLaserFrequencyMin | read-only | mandatory | The minimum adjustable laser frequency in GHz units. |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.3 | ColumnovtxDisplayLaserFrequencyMax | read-only | mandatory | The maximum adjustable laser frequency in GHz units. |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.4 | ColumnovtxDisplayLaserFrequencyStep | read-only | mandatory | The supported laser frequency stepsize in GHz units. |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.5 | ColumnovtxDisplayOmiNominal | read-only | mandatory | The nominal OMI in 0.1 percent units (CATV input) |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.6 | ColumnovtxDisplaySatOmiNominal | read-only | mandatory | The nominal OMI in 0.1 percent units (SAT input) Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.7 | ColumnovtxDisplayRegulationState | read-only | mandatory | The transmitters current regulation state Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports regulationStateUnknownOrNotSuppor… |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.8 | ColumnovtxDisplayExtendedCapabilities | read-only | mandatory | Returns true(1) if the transmitter supports the extended features represented by the variables ovtxConfigurationCsoRegulationMode, ovtxConfigurationSlope and o… |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.9 | ColumnovtxDisplayRfInputCapabilities | read-only | mandatory | Returns the transmitter supported RF input capabilities |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.10 | ColumnovtxDisplaySatLnbSupplySupported | read-only | mandatory | Returns the supported SAT LNB supply features |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.11 | ColumnovtxDisplaySbsExtensionsSupported | read-only | mandatory | Returns true(1) if the transmitter supports the extended SBS alarm features |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.12 | ColumnovtxDisplaySbsSuppressionModeSupported | read-only | mandatory | Returns true(1) if the transmitter supports the SbsSuppressionMode configuration feature |
| 1.3.6.1.4.1.7501.1.2.101.6.1.1.13 | ColumnovtxDisplaySbsFiberParametersSupported | read-only | mandatory | Returns true(1) if the transmitter supports the SbsFiber configuration feature |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AGCmode | INTEGER { modeAgcOff(1), modeUnmodulatedAgcOn(2), modeModulatedAgcOn(3) } | ||
| CsoRegulationMode | INTEGER { csoRegModeChannelControlled(1), csoRegModePilotControlled(2) } | ||
| LaserOutputMode | INTEGER { laserShutdown(1), laserActive(2), laserShutdownOnMaskedError(3) } | ||
| LnbSupplySupportedValue | INTEGER { notSupported(1), lnbSupply14V18VSwitchSupported(2), lnbSupply14V18VAnd22kHzSwitchSupported(3) } | ||
| LnbSupplyValue | INTEGER { lnbSupplyOff(1), lnbSupply14V(2), lnbSupply18V(3), lnbSupply14V_22kHz(4), lnbSupply18V_22kHz(5) } | ||
| NESlotWriteValue | INTEGER (-1..99) | ||
| RedundancyMask | INTEGER { maskAlarmsOnly(1), maskAlarmsAndWarnings(2), maskSpecialAdjusted(3) } | ||
| RedundancyMode | INTEGER { modeActiveLowOutput(1), modeActiveHighOutput(2), modeNominalMasterIrreversible(3), modeNominalMasterFallback(4), modeRedundantSlave(5) } | ||
| RegulationState | INTEGER { regulationStateUnknownOrNotSupported(1), regulationStateOutputpowerBased(2), regulationStateCsoBasedRough(3), regulationStateCsoBasedFine(4), regulationStatePilotBased(5) } | ||
| RfInputAlarmMode | INTEGER { alarmEnableAll(1), alarmCatvEnableSatDisable(2), alarmSatEnableCatvDisable(3) } | ||
| RfInputCapabilities | INTEGER { rfInputCatvOnlySupported(1), rfInputSatOnlySupported(2), rfInputCatvAndSatSupported(3) } | ||
| SatAGCmode | INTEGER { satAgcOff(1), satAgcOn(2) } | ||
| SbsFiberLengthValue | INTEGER { length10km(1), length25km(2), length40km(3), length65km(4) } | ||
| SbsFiberTypeValue | INTEGER { typeStandardFiber(1), typeSbsOptimizedFiber(2) } | ||
| SbsSuppressionModeValue | INTEGER { modeStandard(1), modeCatvOnly(2) } |