CASCADE-MIB
1436 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.277 | Nodecascade | |||
| 1.3.6.1.4.1.277.1 | Nodecascfr | |||
| 1.3.6.1.4.1.277.1.1 | Nodenet | |||
| 1.3.6.1.4.1.277.1.1 | NodenodeBoardInserted | This trap indicates that a board has been inserted into the indicated slot. | ||
| 1.3.6.1.4.1.277.1.1.1 | ScalarnetMask | read-write | mandatory | The IP subnet mask for the network. The default is 255.255.255.0 (class C) which allows 254 nodes. |
| 1.3.6.1.4.1.277.1.1.2 | ScalarnetNumber | read-write | mandatory | The IP network number for the network. |
| 1.3.6.1.4.1.277.1.1.3 | ScalarnetDlciAddrSig | read-write | mandatory | This variable states the DLCI addressing significance. |
| 1.3.6.1.4.1.277.1.1.4 | ScalarnetMaxSegsize | read-write | mandatory | This variable states the maximum sgement size for the network. |
| 1.3.6.1.4.1.277.1.1.8 | ScalarnetSmdsAreaMaskStart | read-write | mandatory | This variable states the starting digit number for defining the start of the Area Mask for SMDS Addresses. |
| 1.3.6.1.4.1.277.1.1.9 | ScalarnetSmdsAreaMaskDigits | read-write | mandatory | This variable states the number of digits used for defining the Area Mask for SMDS Addresses. |
| 1.3.6.1.4.1.277.1.2 | Nodease | |||
| 1.3.6.1.4.1.277.1.2 | NodenodeBoardPulled | This trap indicates that a board has been pulled out from the indicated slot. | ||
| 1.3.6.1.4.1.277.1.2.1 | TableaseTable | not-accessible | mandatory | A list of ASE entries. |
| 1.3.6.1.4.1.277.1.2.1.1 | RowaseEntry | not-accessible | mandatory | An ASE entry contains an external NMS path accessible from the node. |
| 1.3.6.1.4.1.277.1.2.1.1.1 | ColumnaseAddr | read-only | mandatory | IP Address for an external NMS. |
| 1.3.6.1.4.1.277.1.2.1.1.2 | ColumnaseMask | read-only | mandatory | IP Address mask for an external NMS. The default value is 255.255.255.255. |
| 1.3.6.1.4.1.277.1.2.1.1.3 | ColumnaseDefaultGwAddr | read-write | mandatory | Default Gateway IP Address for reaching the external NMS. This field is not applicable to NMSs which are reachable via SLIP or on the same Ethernet. |
| 1.3.6.1.4.1.277.1.2.1.1.4 | ColumnaseMetricType | read-only | mandatory | Type of metric (1 or 2) for each external NMS. The default is 1. (This field is not applicable to SLIP- based hosts.) |
| 1.3.6.1.4.1.277.1.2.1.1.5 | ColumnaseAdminStatus | read-write | mandatory | The desired state of the entry. |
| 1.3.6.1.4.1.277.1.2.1.1.6 | ColumnaseIfIndex | read-write | mandatory | The interface value of the corresponding MIB-II ifEntry. |
| 1.3.6.1.4.1.277.1.2.1.1.7 | ColumnaseDlci | read-write | mandatory | The management dlci through which the NMS communicates to the switch. |
| 1.3.6.1.4.1.277.1.3 | Nodenode | |||
| 1.3.6.1.4.1.277.1.3 | NodenodeBoardMismatch | This trap indicates that the actual board type on the indicated slot is inconsistent with what is configured. | ||
| 1.3.6.1.4.1.277.1.3.1 | ScalarnodeIpAddr | read-write | mandatory | The inband IP address of the node in the Cascade internal trunk IP network. |
| 1.3.6.1.4.1.277.1.3.2 | ScalarnodeLanIpAddr | read-write | mandatory | The inband (Ethernet) IP address of the node for a NMS to access the node and the internal trunk IP network. |
| 1.3.6.1.4.1.277.1.3.3 | TablenodeNMSTable | not-accessible | mandatory | A list of NMS entries. |
| 1.3.6.1.4.1.277.1.3.3.1 | RownodeNMSEntry | not-accessible | mandatory | A NMS entry contains an IP address of a NMS which has extended privilages. |
| 1.3.6.1.4.1.277.1.3.3.1.1 | ColumnnodeNMSIndex | read-only | mandatory | The IP address entry of a primary Network Management Station. |
| 1.3.6.1.4.1.277.1.3.3.1.2 | ColumnnodeNMSIpAddr | read-write | mandatory | The IP address of the primary Network Management Station. It is to this address that Traps and TFTP requests will be directed. |
| 1.3.6.1.4.1.277.1.3.4 | ScalarnodeState | read-write | mandatory | The state of the switch. The switch needs to await the state to be set to active before being fully operational after cold boot, when the NMS is reachable. |
| 1.3.6.1.4.1.277.1.3.5 | ScalarnodePollStatus | read-only | mandatory | The consolidated node status in response to keep-alive polls. It is an octet string of a proprietary format |
| 1.3.6.1.4.1.277.1.3.6 | ScalarnodeModel | read-only | mandatory | The part number of the node. |
| 1.3.6.1.4.1.277.1.3.7 | ScalarnodeSerial | read-only | mandatory | The serial number (i.e., Ethernet Addr) of the switch. |
| 1.3.6.1.4.1.277.1.3.8 | ScalarnodeSwRev | read-only | mandatory | The software revision number (major.minor). |
| 1.3.6.1.4.1.277.1.3.9 | ScalarnodeHwRev | read-only | mandatory | The hardware revision number (major.minor). |
| 1.3.6.1.4.1.277.1.3.10 | ScalarnodeEpromRev | read-only | mandatory | The EPROM firmware revision number (major.minor). |
| 1.3.6.1.4.1.277.1.3.11 | ScalarnodeCpuUtil | read-only | mandatory | The CPU utilization percentage for packet processing. |
| 1.3.6.1.4.1.277.1.3.12 | ScalarnodePsAStatus | read-only | mandatory | The status of the power supply A. For a detailed explanation for the power supply being either in the down or marginal state, refer to the nodePsADiagCode obje… |
| 1.3.6.1.4.1.277.1.3.13 | ScalarnodePsBStatus | read-only | mandatory | The status of the power supply B. For a detailed explanation for the power supply being either in the down or marginal state, refer to the nodePsBDiagCode obje… |
| 1.3.6.1.4.1.277.1.3.14 | TablenodeFanTable | not-accessible | mandatory | A list of fan entries. |
| 1.3.6.1.4.1.277.1.3.14.1 | RownodeFanEntry | not-accessible | mandatory | A Fan entry contains the status of a fan. |
| 1.3.6.1.4.1.277.1.3.14.1.1 | ColumnnodeFanIndex | read-only | mandatory | A unique value for each fan. |
| 1.3.6.1.4.1.277.1.3.14.1.2 | ColumnnodeFanStatus | read-only | mandatory | The status of the fan. |
| 1.3.6.1.4.1.277.1.3.14.1.3 | ColumnnodeFanSpeed | read-only | mandatory | The speed in Revolutions Per. Minute (RPM) of the fan. |
| 1.3.6.1.4.1.277.1.3.15 | ScalarnodeMemoryUtil | read-only | mandatory | The percentage of system memory utilization on this intelligent card. |
| 1.3.6.1.4.1.277.1.3.16 | ScalarnodeMemoryUsage | read-only | mandatory | The system memory utilization, in terms of free bytes, for this intelligent card. |
| 1.3.6.1.4.1.277.1.3.17 | ScalarnodeMaxFramesize | read-only | mandatory | The maximum frame size supported by the node. The default is 4096. |
| 1.3.6.1.4.1.277.1.3.18 | ScalarnodeQOSPollTimer | read-write | mandatory | The timer (seconds) for generating QOS polling packets. |
| 1.3.6.1.4.1.277.1.3.19 | ScalarnodeActivePvcs | read-only | mandatory | The number of currently active PVCs on the node. |
| 1.3.6.1.4.1.277.1.3.20 | ScalarnodeInactivePvcs | read-only | mandatory | The number of currently inactive PVCs on the node. |
| 1.3.6.1.4.1.277.1.3.21 | ScalarnodePendingPvcs | read-only | mandatory | The number of currently call pending PVCs on the node. |
| 1.3.6.1.4.1.277.1.3.22 | ScalarnodeInOctets | read-only | mandatory | The total number of octets received on the node, including framing bytes. |
| 1.3.6.1.4.1.277.1.3.23 | ScalarnodeInPkts | read-only | mandatory | The total number of packets received on the node. |
| 1.3.6.1.4.1.277.1.3.24 | ScalarnodeOutOctets | read-only | mandatory | The total number of octets transmitted out of the node, including framing bytes. |
| 1.3.6.1.4.1.277.1.3.25 | ScalarnodeOutPkts | read-only | mandatory | The total number of packets requested to be transmitted out of the node, including those that were discarded or not sent. |
| 1.3.6.1.4.1.277.1.3.26 | ScalarnodeSwFilename | read-write | mandatory | Name of the file to be downloaded. |
| 1.3.6.1.4.1.277.1.3.27 | ScalarnodeRebootAfterLoad | read-write | mandatory | Instructs the device to either automatically reboot after the successful scheduled download or not. |
| 1.3.6.1.4.1.277.1.3.28 | ScalarnodeSwToLoad | read-write | mandatory | Instructs the device to initiate a software download (via tftp) request to the master management station after the specified time ticks have elapsed. |
| 1.3.6.1.4.1.277.1.3.29 | ScalarnodeSwLoadState | read-write | mandatory | The state of the software download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by setting this object to INACT… |
| 1.3.6.1.4.1.277.1.3.30 | ScalarnodePrFilename | read-write | mandatory | Name of the PRAM image file to be downloaded. |
| 1.3.6.1.4.1.277.1.3.31 | ScalarnodePrToLoad | read-write | mandatory | Instructs the device to initiate a PRAM image file download (via tftp) request to the master management station after the specified time ticks have elapsed. |
| 1.3.6.1.4.1.277.1.3.32 | ScalarnodePrLoadState | read-write | mandatory | The state of the PRAM download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by setting this object to INACTIVE. |
| 1.3.6.1.4.1.277.1.3.33 | ScalarnodeToWarmboot | read-write | mandatory | Instructs the switch to initiate a system warm boot after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously schedule… |
| 1.3.6.1.4.1.277.1.3.34 | ScalarnodeToColdboot | read-write | mandatory | Instructs the switch to initiate a system cold boot after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously schedule… |
| 1.3.6.1.4.1.277.1.3.35 | ScalarnodeToRedundant | read-write | mandatory | If redundancy is configured, instructs the node acting as Backup to disable the Active node and take over as the Active node. The disabling is initiated after … |
| 1.3.6.1.4.1.277.1.3.36 | ScalarnodeInitiateBulkStats | read-write | mandatory | Initiates a Bulk Statistics poll and via TFTP, transfer the data to the specified IP address. |
| 1.3.6.1.4.1.277.1.3.37 | ScalarnodeDiagNonFatalSource | read-only | mandatory | Source who reported last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.38 | ScalarnodeDiagNonFatalTime | read-only | mandatory | Time the last non-fatal error was reported. |
| 1.3.6.1.4.1.277.1.3.39 | ScalarnodeDiagNonFatalErrMajor | read-only | mandatory | Major error code of last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.40 | ScalarnodeDiagNonFatalErrMinor | read-only | mandatory | Minor error code of last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.41 | ScalarnodeDiagNonFatalStr | read-only | mandatory | Ascii string describing last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.42 | ScalarnodeDiagFatalSource | read-only | mandatory | Source who reported last fatal error. |
| 1.3.6.1.4.1.277.1.3.43 | ScalarnodeDiagFatalTime | read-only | mandatory | Time the last fatal error was reported. |
| 1.3.6.1.4.1.277.1.3.44 | ScalarnodeDiagFatalErrMajor | read-only | mandatory | Major error code of last fatal error. |
| 1.3.6.1.4.1.277.1.3.45 | ScalarnodeDiagFatalErrMinor | read-only | mandatory | Minor error code of last fatal error. |
| 1.3.6.1.4.1.277.1.3.46 | ScalarnodeDiagFatalStr | read-only | mandatory | Ascii string describing last fatal error. |
| 1.3.6.1.4.1.277.1.3.47 | ScalarnodeDiagFatalReboots | read-only | mandatory | Number of times the switch has re-booted since last fatal error was reported. |
| 1.3.6.1.4.1.277.1.3.48 | ScalarnodeDiagFatalAddress | read-only | mandatory | Address switch was executing when it encountered fatal error. |
| 1.3.6.1.4.1.277.1.3.49 | ScalarnodeDiagBackgroundPasses | read-only | mandatory | Number of passes made by the background diagnostics. |
| 1.3.6.1.4.1.277.1.3.50 | ScalarnodeDiagBackgroundFailures | read-only | mandatory | Number of failures discovered by background diagnostics. |
| 1.3.6.1.4.1.277.1.3.51 | ScalarnodeDiagBackgroundSuccesses | read-only | mandatory | Number of successful passes by background diagnostics. |
| 1.3.6.1.4.1.277.1.3.52 | ScalarnodeDiagLEDReset | read-write | mandatory | Change the node state from marginal to active. Change the LED from yellow to green. |
| 1.3.6.1.4.1.277.1.3.53 | ScalarnodeDiagPowerExtensive | read-write | mandatory | Should power on diagnostics do slower, extensive testing, or fast testing? |
| 1.3.6.1.4.1.277.1.3.54 | ScalarnodePortPoll | read-only | mandatory | The consolidated port status in response to keep-alive polls. |
| 1.3.6.1.4.1.277.1.3.55 | ScalarnodeMaxTelnetConsole | read-write | mandatory | The number of concurrent telnet consoles allowed. The default is 2. The maximum is 5. Set it 0 to disable telnet access. |
| 1.3.6.1.4.1.277.1.3.56 | ScalarnodeConsoleTimeout | read-write | mandatory | Idle-logoff timer in minutes. The default is 5 minutes, and the maximum can be set is 60 minutes. To disable idle-logout, set this to 0. |
| 1.3.6.1.4.1.277.1.3.57 | TablenodeConsoleTable | not-accessible | mandatory | A list of active consoles on the node, logged in through telnet or serial port. |
| 1.3.6.1.4.1.277.1.3.57.1 | RownodeConsoleEntry | not-accessible | mandatory | Information of a console. |
| 1.3.6.1.4.1.277.1.3.57.1.1 | ColumnnodeConsoleIndex | read-only | mandatory | A positive integer to identify a console |
| 1.3.6.1.4.1.277.1.3.57.1.2 | ColumnnodeUserName | read-only | mandatory | The login user name up to 31 characters. There is no validation of the name, i.e., any string is acceptable. |
| 1.3.6.1.4.1.277.1.3.57.1.3 | ColumnnodeUserFrom | read-only | mandatory | The IP address from which the user logged in. 0.0.0.0 if the user logged in through serial port. |
| 1.3.6.1.4.1.277.1.3.57.1.4 | ColumnnodeConsoleAccessMode | read-only | mandatory | The access mode of the console. By default, a user is in READ ONLY mode. |
| 1.3.6.1.4.1.277.1.3.57.1.5 | ColumnnodeConsoleUptime | read-only | mandatory | How long the console has been active. |
| 1.3.6.1.4.1.277.1.3.58 | ScalarnodePsADiagCode | read-only | mandatory | The failure code of the power supply A. A non-zero value indicates one or more failures. Refer to the hardware manual for a description of the failure code. |
| 1.3.6.1.4.1.277.1.3.59 | ScalarnodePsBDiagCode | read-only | mandatory | The failure code of the power supply B. A non-zero value indicates one or more failures. Refer to the hardware manual for a description of the failure code. |
| 1.3.6.1.4.1.277.1.3.60 | ScalarnodeFrameMemoryUtil | read-only | mandatory | The percentage of frame memory utilization on this intelligent card. |
| 1.3.6.1.4.1.277.1.3.61 | ScalarnodeFrameMemoryUsage | read-only | mandatory | The frame memory utilization, in terms of free bytes, for this intelligent card. |
| 1.3.6.1.4.1.277.1.3.62 | ScalarnodeCapability | read-only | mandatory | The capability of this node. |
| 1.3.6.1.4.1.277.1.3.63 | ScalarnodeSvcLastCallFailure | read-only | mandatory | A textual string describing the last call failure. |
| 1.3.6.1.4.1.277.1.3.64 | ScalarnodeRerouteDelay | read-write | mandatory | The number of seconds delay between each reroute batch event. |
| 1.3.6.1.4.1.277.1.3.65 | ScalarnodeRerouteCount | read-write | mandatory | The number of virtual circuits to request a reroute for duing a single reroute batch event. |
| 1.3.6.1.4.1.277.1.3.66 | ScalarnodeFileTransferRequest | read-write | mandatory | This object is used to initiate file transfers to and from the switch. A management station can initiate a file transfer by settting this object of text string… |
| 1.3.6.1.4.1.277.1.3.67 | ScalarnodeFileTransferStatus | read-only | mandatory | The status of the file tarnsfer. |
| 1.3.6.1.4.1.277.1.3.68 | ScalarnodeTime | read-write | mandatory | The current wall-clock time that is set on the switch in Universal Coordinated Time (UCT). The value is the number of seconds since 00:00:00 UCT January 1, 197… |
| 1.3.6.1.4.1.277.1.3.69 | ScalarnodeBillingAPAddress | read-write | mandatory | The IP Address of the Adjunct Billing Processor that is servicing this switch. |
| 1.3.6.1.4.1.277.1.3.70 | ScalarnodeBillingAPUsername | read-write | mandatory | The Username of the account on the Adjunct Billing Processor to which usage data will be transferred via FTP. |
| 1.3.6.1.4.1.277.1.3.71 | ScalarnodeBillingAPPassword | read-write | mandatory | The Password corresponding to the account identified by nodeBillingAPUsername. A NULL string is returned when read. |
| 1.3.6.1.4.1.277.1.3.72 | ScalarnodeBillingSwAPCommsFailures | read-write | mandatory | The number of times that communication from the switch to the Adjunct Billing Processor has failed during the current aggregation period. A failure signifies f… |
| 1.3.6.1.4.1.277.1.3.73 | TablenodeBillingTable | not-accessible | mandatory | A table of Billing System managable objects, indexed by service. |
| 1.3.6.1.4.1.277.1.3.73.1 | RownodeBillingEntry | not-accessible | mandatory | A nodeBillingEntry contains a set of statistics that summarize the Billing System performance for a particular service. |
| 1.3.6.1.4.1.277.1.3.73.1.1 | ColumnnodeBillingService | read-only | mandatory | The service being reported. This is the index into the table. Additional table rows for Frame Relay and ATM may be provided in the future. |
| 1.3.6.1.4.1.277.1.3.73.1.2 | ColumnnodeBilling | read-write | mandatory | Switch to enable and disable billing on the STDX. When the value of nodeBilling is 'enabled', the value of a logical port's lportBilling object will take prece… |
| 1.3.6.1.4.1.277.1.3.73.1.3 | ColumnnodeBillingAggrPeriod | read-write | mandatory | Defines the length of the Billing Aggregation Period in seconds. The default value is 15 minutes. The minimum value is 10 minutes. |
| 1.3.6.1.4.1.277.1.3.73.1.4 | ColumnnodeBillingCurAggrPeriodStart | read-only | mandatory | The start-time of the current aggregation period, given by the number of seconds since 00:00:00 UCT January 1, 1970. |
| 1.3.6.1.4.1.277.1.3.73.1.5 | ColumnnodeBillingCurAggrPeriodEnd | read-only | mandatory | The end-time of the current aggregation period, given by the number of seconds since 00:00:00 UCT January 1, 1970. |
| 1.3.6.1.4.1.277.1.3.73.1.6 | ColumnnodeBillingCollection | read-write | mandatory | Defines how often the Data Aggregation process on the CP is to poll the IOPs for usage data. The default value is 30 second. The range is unbounded, but practi… |
| 1.3.6.1.4.1.277.1.3.73.1.7 | ColumnnodeBillingDailyProcessing | read-write | mandatory | Defines whether the Billing System is to perform a set of carrier-specific actions at the time given by nodeBillingDPTime. This object can be used to schedule … |
| 1.3.6.1.4.1.277.1.3.73.1.8 | ColumnnodeBillingDPTime | read-write | mandatory | Defines the time (given by the number of seconds since 00:00:00 UCT) that the Billing System is to perform a set of carrier-specific actions. This object can b… |
| 1.3.6.1.4.1.277.1.3.73.1.9 | ColumnnodeBillingUsageRecOvflWarnings | read-only | mandatory | Count of the number of usage record counter-value overflow conditions that have occurred during the current aggregation period. An overflow condition exists wh… |
| 1.3.6.1.4.1.277.1.3.73.1.10 | ColumnnodeBillingTotalUsageRecOvflWarnings | read-only | mandatory | Count of the number of usage record overflow conditions that have occurred during the current day. |
| 1.3.6.1.4.1.277.1.3.73.1.11 | ColumnnodeBillingBillableUsageEvents | read-only | mandatory | Count of the number of data units (e.g, SMDS L3 PDUs) processed for billing treatment. |
| 1.3.6.1.4.1.277.1.3.73.1.12 | ColumnnodeBillingNonBillableUsageEvents | read-only | mandatory | Count of the number of data units (e.g, SMDS L3 PDUs) not considered for billing treatment. |
| 1.3.6.1.4.1.277.1.3.73.1.13 | ColumnnodeBillingUsageRecCreated | read-only | mandatory | Count of the number of usage records created during the current aggregation period. |
| 1.3.6.1.4.1.277.1.3.73.1.14 | ColumnnodeBillingTotalUsageRecCreated | read-only | mandatory | Count of the total number of usage records created during the current day. |
| 1.3.6.1.4.1.277.1.3.73.1.15 | ColumnnodeBillingUsageRecCrFailures | read-only | mandatory | Total number of usage records that could not be created during the current aggregation period. This counter is normally incremented when the usage data file is… |
| 1.3.6.1.4.1.277.1.3.73.1.16 | ColumnnodeBillingTotalUsageRecCrFailures | read-only | mandatory | Total number of usage records that could not be created during the current day. |
| 1.3.6.1.4.1.277.1.3.73.1.17 | ColumnnodeBillingUsageRecSent | read-only | mandatory | Total number of usage records that have been transferred to the Adjunct Billing Processor during the current aggregation period. |
| 1.3.6.1.4.1.277.1.3.73.1.18 | ColumnnodeBillingTotalUsageRecSent | read-only | mandatory | Total number of usage records that have been transferred to the Adjunct Billing Processor during the current day. |
| 1.3.6.1.4.1.277.1.3.73.1.19 | ColumnnodeBillingUsageDataStoreFull | read-only | mandatory | The number of times the aggregated usage data store became full during the current aggregation period. |
| 1.3.6.1.4.1.277.1.3.73.1.20 | ColumnnodeBillingTotalUsageDataStoreFull | read-only | mandatory | Total number of times the aggregated usage data store became full during the current day. |
| 1.3.6.1.4.1.277.1.3.73.1.21 | ColumnnodeBillingAdminAction | read-write | mandatory | This object defines a set of administrative actions that can be performed by the Billing System. forceUpload - Forces the current aggregation period to end and… |
| 1.3.6.1.4.1.277.1.3.74 | ScalarnodeRerouteAlg | read-write | mandatory | The number of seconds delay between each reroute batch event. |
| 1.3.6.1.4.1.277.1.3.76 | ScalarnodeOamAlarmDisabled | read-write | mandatory | If disabled then don't generate oam alarms for circuits that are down on this switch. |
| 1.3.6.1.4.1.277.1.3.77 | TablenodeRefclocksrcTable | not-accessible | mandatory | A list of generators (sources) for the system reference clock on the node. This reference clock is used by the clock generation unit (CGU) to create the system… |
| 1.3.6.1.4.1.277.1.3.77.1 | RownodeRefclocksrcEntry | not-accessible | mandatory | Information of a single system reference clock source. |
| 1.3.6.1.4.1.277.1.3.77.1.1 | ColumnnodeRefclocksrcIndex | read-write | mandatory | A positive integer to identify an entry in the nodeRefclocksrcTable. |
| 1.3.6.1.4.1.277.1.3.77.1.2 | ColumnnodeRefclocksrcPriority | read-write | mandatory | The priority of the system reference clock source. A source with a nodeRefclocksrcPriority=n means that this source is used before a source with a higher value… |
| 1.3.6.1.4.1.277.1.3.77.1.3 | ColumnnodeRefclocksrcType | read-write | mandatory | The type of the reference clock source. It is either an external clock source connected to a ATM-IWU or DS3 card, or the reference clock is recovered from the … |
| 1.3.6.1.4.1.277.1.3.77.1.4 | ColumnnodeRefclocksrcSlotId | read-write | mandatory | The card number of the reference clock source. In case of an external clock interface this is the number of the card as defined in cardLogicalSlotId. In case o… |
| 1.3.6.1.4.1.277.1.3.77.1.5 | ColumnnodeRefclocksrcPportId | read-write | mandatory | The interface number of the reference clock source. In case of an external clock interface this is meaningless. In case of a clock recovered from the line inte… |
| 1.3.6.1.4.1.277.1.3.78 | ScalarnodeRefclockActiveSrc | read-only | mandatory | The entry number of the active reference clock source in nodeRefclocksrcTable. If zero, the CGU is in free-running mode or holdover mode using the last PLL par… |
| 1.3.6.1.4.1.277.1.3.79 | ScalarnodeRefclockActiveCGUSlotId | read-only | mandatory | The physical slot id of the current master CGU board. |
| 1.3.6.1.4.1.277.1.3.80 | ScalarnodeRefclockActiveCGUMode | read-only | mandatory | The clock mode of the current master CGU board. |
| 1.3.6.1.4.1.277.1.3.81 | ScalarnodeInitiateImageBackup | read-write | mandatory | When set, copy all of the runtime application images and configuration images to there corresponding backup locations on the hard disk. |
| 1.3.6.1.4.1.277.1.3.82 | ScalarnodeImageBackupState | read-only | mandatory | Provides the current state of the images backup operation. |
| 1.3.6.1.4.1.277.1.3.83 | ScalarnodeInitiateImageRestore | read-write | mandatory | When set, copy all of the runtime application images and configuration images from their BACKUP locations on the hard disk to there corresponding ACTIVE locati… |
| 1.3.6.1.4.1.277.1.3.84 | TablenodeApplicationTable | not-accessible | mandatory | A list of Application Image Descriptions. |
| 1.3.6.1.4.1.277.1.3.84.1 | RownodeApplicationEntry | not-accessible | mandatory | An Application Entry contains a description of the application image, the version of the PRIMARY copy and the version of the SECONDARY copy. |
| 1.3.6.1.4.1.277.1.3.84.1.1 | ColumnnodeApplicationIndex | read-only | mandatory | The numeric index of application images. 1 - SP Runtime Application 2 - IOM Type A Runtime Application 3 - IOM Type B Runtime Application 4 - IOM Type C Runtim… |
| 1.3.6.1.4.1.277.1.3.84.1.2 | ColumnnodeApplicationDescription | read-only | mandatory | The description of this Application Image. |
| 1.3.6.1.4.1.277.1.3.84.1.3 | ColumnnodePrimaryVersion | read-only | mandatory | The version of the PRIMARY Application Image. |
| 1.3.6.1.4.1.277.1.3.84.1.4 | ColumnnodeSecondaryVersion | read-only | mandatory | The version of the SECONDARY Application Image. |
| 1.3.6.1.4.1.277.1.3.85 | ScalarnodePrimarySyncRefAdminState | read-write | mandatory | The requested primary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.86 | ScalarnodePrimarySyncRefOperationalState | read-only | mandatory | The actual primary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.87 | ScalarnodeSecondarySyncRefAdminState | read-write | mandatory | The requested secondary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.88 | ScalarnodeSecondarySyncRefOperationalState | read-only | mandatory | The actual secondary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.89 | ScalarnodePrimaryPLLOperationalState | read-only | mandatory | The current state of the primary synchronization PLL. |
| 1.3.6.1.4.1.277.1.3.90 | ScalarnodeSecondaryPLLOperationalState | read-only | mandatory | The current state of the secondary synchronization PLL. |
| 1.3.6.1.4.1.277.1.3.91 | ScalarnodeExternalClockAOperationalState | read-only | mandatory | The current state of the External Clock A reference. |
| 1.3.6.1.4.1.277.1.3.92 | ScalarnodeExternalClockBOperationalState | read-only | mandatory | The current state of the External Clock B reference. |
| 1.3.6.1.4.1.277.1.3.93 | ScalarnodePortClockAOperationalState | read-only | mandatory | The current state of the Port Clock A reference. |
| 1.3.6.1.4.1.277.1.3.94 | ScalarnodePortClockBOperationalState | read-only | mandatory | The current state of the Port Clock B reference. |
| 1.3.6.1.4.1.277.1.3.95 | ScalarnodeExternalTimingSource | read-write | mandatory | The reference for the external timing output. |
| 1.3.6.1.4.1.277.1.3.96 | ScalarnodeSyncAutoRestore | read-write | mandatory | The configuration of the Synchronization Reference Auto Restoration function. |
| 1.3.6.1.4.1.277.1.3.97 | ScalarnodeExternalClockInterfaceType | read-only | mandatory | The interface type of the External Clock references. |
| 1.3.6.1.4.1.277.1.4 | NodenodePsAStatusChange | This trap indicates that the power supply A has changed state (toggled between up and down states). | ||
| 1.3.6.1.4.1.277.1.4 | Nodepport | |||
| 1.3.6.1.4.1.277.1.4.1 | ScalarpportNumber | read-only | mandatory | The number of physical ports (regardless of their current state) present at this node. |
| 1.3.6.1.4.1.277.1.4.2 | TablepportTable | not-accessible | mandatory | A list of physical port entries. The number of entries is given by the value of pportNumber. |
| 1.3.6.1.4.1.277.1.4.2.1 | RowpportEntry | not-accessible | mandatory | The physical port entry contains objects relevant to a physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.1 | ColumnpportSlotId | read-only | mandatory | The slot number of the corresponding physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.2 | ColumnpportId | read-only | mandatory | The port number of the corresponding physical port on the board. |
| 1.3.6.1.4.1.277.1.4.2.1.3 | ColumnpportAdminType | read-write | mandatory | The defined type of the board which the physical port is on. |
| 1.3.6.1.4.1.277.1.4.2.1.4 | ColumnpportNumLport | read-only | mandatory | The number of logical ports on the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.5 | ColumnpportDataRate | read-write | mandatory | An estimate of the physical port's data rate in bits per second. The data rate can't be an arbitrary value. The legal values are list below. Note that the T1/E… |
| 1.3.6.1.4.1.277.1.4.2.1.6 | ColumnpportType | read-only | mandatory | The actual type of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.7 | ColumnpportRecvClock | read-only | mandatory | The receive clock source. This object works in cooperation with pportXmitClock. The following are the various values for different clock source types: Type Clo… |
| 1.3.6.1.4.1.277.1.4.2.1.8 | ColumnpportXmitClock | read-only | mandatory | The transmit clock source. This object works in cooperation with pportXmitClock. The following are the various values for different clock source types: Type Cl… |
| 1.3.6.1.4.1.277.1.4.2.1.9 | ColumnpportAdminStatus | read-write | mandatory | The desired state of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.10 | ColumnpportOperStatus | read-only | mandatory | The current state of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.11 | ColumnpportDs1LineType | read-write | mandatory | The line type of the T1 or FT1-24B port. ANSI ESF is equivalent to Bellcore ESF. |
| 1.3.6.1.4.1.277.1.4.2.1.12 | ColumnpportDs1ZeroCoding | read-write | mandatory | The variety of zero code suppression used on the T1 or FT1-24B link. Jammed bit is equivalent to dsx1JBZS where the DS0s will run at 56K bps. |
| 1.3.6.1.4.1.277.1.4.2.1.13 | ColumnpportDs1LineBuildout | read-write | mandatory | The line build out or line length specification for the DS1 or DSX-1 transmitter. These values are card specific: 10 port DSX-1 card The accepted values are: 1… |
| 1.3.6.1.4.1.277.1.4.2.1.14 | ColumnpportDiagTestId | read-write | mandatory | Identification for the diagnostics tests to be run. |
| 1.3.6.1.4.1.277.1.4.2.1.15 | ColumnpportDiagTestRuns | read-write | mandatory | The number of passes of the diagnostics tests to be run. The default value is 1. |
| 1.3.6.1.4.1.277.1.4.2.1.16 | ColumnpportInOctets | read-only | mandatory | The total number of octets received on the physical port, including framing characters. |
| 1.3.6.1.4.1.277.1.4.2.1.17 | ColumnpportInFrames | read-only | mandatory | The total number of frames received on the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.18 | ColumnpportInDiscards | read-only | mandatory | The total number of inbound frames discarded. |
| 1.3.6.1.4.1.277.1.4.2.1.19 | ColumnpportInErrors | read-only | mandatory | The total number of inbound frames that contained erroneous headers (e.g., illegal or unknown DLCIs). |
| 1.3.6.1.4.1.277.1.4.2.1.20 | ColumnpportOutOctets | read-only | mandatory | The total number of octets transmitted out of the physical port, including framing characters. |
| 1.3.6.1.4.1.277.1.4.2.1.21 | ColumnpportOutFrames | read-only | mandatory | The total number of frames transmitted out of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.22 | ColumnpportOutDiscards | read-only | mandatory | The total number of outbound frames discarded due to severe congestion. |
| 1.3.6.1.4.1.277.1.4.2.1.23 | ColumnpportOutErrors | read-only | mandatory | The total number of outbound frames that causes xmit errors. |
| 1.3.6.1.4.1.277.1.4.2.1.24 | ColumnpportDiagState | read-write | mandatory | The current state of the diagnostic on this physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.25 | ColumnpportDiagOptionStr | read-write | mandatory | Optional parameters to the diagnostic. |
| 1.3.6.1.4.1.277.1.4.2.1.26 | ColumnpportDiagPassCount | read-only | mandatory | Number of successful diagnostic passes. |
| 1.3.6.1.4.1.277.1.4.2.1.27 | ColumnpportDiagFailCount | read-only | mandatory | Number of failed diagnostic passes. |
| 1.3.6.1.4.1.277.1.4.2.1.28 | ColumnpportDiagResultStr | read-only | mandatory | Description of last diagnostic failure. |
| 1.3.6.1.4.1.277.1.4.2.1.29 | ColumnpportLinkDownReason | read-only | mandatory | Reason why the link is down. The blue-alarm is equivalent to the Alarm Indication Signal (AIS) failure. |
| 1.3.6.1.4.1.277.1.4.2.1.30 | ColumnpportInterface | read-only | mandatory | Actual interface connected to Multi-Interface Port or ATM-IWU. |
| 1.3.6.1.4.1.277.1.4.2.1.31 | ColumnpportAdminInterface | read-write | mandatory | Configured interface connected to Multi-Interface Port or ATM-IWU. |
| 1.3.6.1.4.1.277.1.4.2.1.32 | ColumnpportCellScramble | read-write | mandatory | Configured ATM cell payload scrambling. |
| 1.3.6.1.4.1.277.1.4.2.1.33 | ColumnpportCbitParity | read-write | mandatory | Configured ATM DS3 C-bit Parity. |
| 1.3.6.1.4.1.277.1.4.2.1.34 | ColumnpportMaxBufferSize | read-write | mandatory | Maximum receive/transmit buffer size for the ATM UNI DS3 IOP |
| 1.3.6.1.4.1.277.1.4.2.1.35 | ColumnpportPeakCellRate0 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #0. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.36 | ColumnpportPeakCellRate1 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #1. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.37 | ColumnpportPeakCellRate2 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #2. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.38 | ColumnpportPeakCellRate3 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #3. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.39 | ColumnpportPeakCellRate4 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #4. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.40 | ColumnpportPeakCellRate5 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #5. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.41 | ColumnpportPeakCellRate6 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #6. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.42 | ColumnpportPeakCellRate7 | read-write | mandatory | Peak Cell Rate (cell/sec.) for rate queue #7. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.43 | ColumnpportInCells | read-only | mandatory | The total number of cells received |
| 1.3.6.1.4.1.277.1.4.2.1.44 | ColumnpportInErrorCells | read-only | mandatory | The total number of cells received with error |
| 1.3.6.1.4.1.277.1.4.2.1.45 | ColumnpportOutCells | read-only | mandatory | The total number of cells transmitted |
| 1.3.6.1.4.1.277.1.4.2.1.46 | ColumnpportDs3LineBuildout | read-write | mandatory | The line build out or line length specification for the DS3 transmitter. 1-port ATM-UNI DS3 card The accepted values are: 1 - 0 to 225 feet 2 - 226 to 450 feet |
| 1.3.6.1.4.1.277.1.4.2.1.47 | ColumnpportSetDS0LoopUp | read-write | mandatory | Bit map used to set one or more DS0's into loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put into loopback. |
| 1.3.6.1.4.1.277.1.4.2.1.48 | ColumnpportSetDS0LoopDown | read-write | mandatory | Bit map used to set one or more DS0's out of loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put out of loopback. |
| 1.3.6.1.4.1.277.1.4.2.1.49 | ColumnpportDS0LoopUpStatus | read-only | mandatory | Bit map reporting which DS0's have gone into loopback since the last time this variable was read |
| 1.3.6.1.4.1.277.1.4.2.1.50 | ColumnpportDS0LoopDownStatus | read-only | mandatory | Bit map reporting which DS0's have gone out of loopback since the last time this variable was read |
| 1.3.6.1.4.1.277.1.4.2.1.51 | ColumnpportDS0LoopStatus | read-only | mandatory | Bit map reporting which DS0's are currently in loopback. Low bit corresponds to DS0 1 |
| 1.3.6.1.4.1.277.1.4.2.1.52 | ColumnpportISDN | read-write | mandatory | Specifies whether ISDN PRI is enabled for this physical port |
| 1.3.6.1.4.1.277.1.4.2.1.53 | Columnpportdsx3LoopbackConfig | read-write | mandatory | Integer used to set the loopback state of the DS3 or E3 |
| 1.3.6.1.4.1.277.1.4.2.1.54 | Columnpportdsx3SendCode | read-write | mandatory | Integer used to send loopback code to far-end DS3 |
| 1.3.6.1.4.1.277.1.4.2.1.55 | Columnpportdsx3LoopStatus | read-only | mandatory | Integer indicating the current loopback status of the DS3 or E3 |
| 1.3.6.1.4.1.277.1.4.2.1.56 | Columnpportdsx3FEACStatus | read-only | mandatory | Integer indicating the current DS3 FAEC status: DS3 Equipment Failure (1), DS3 LOS (2), DS3 Out of Frame (4), DS3 AIS received (8), DS3 IDLE received (16), DS3… |
| 1.3.6.1.4.1.277.1.4.2.1.57 | Columnpportds1LoopbackConfig | read-write | mandatory | Integer used to set the loopback state of the DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.58 | Columnpportds1SendCode | read-write | mandatory | Integer used to send loopback code to far-end DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.59 | Columnpportds1LoopStatus | read-only | mandatory | Integer indicating the current loopback status of the DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.60 | ColumnpportSetClkBkup | read-only | mandatory | The desired clock source backup if the card is set in external clock source mode |
| 1.3.6.1.4.1.277.1.4.2.1.61 | ColumnpportAtmIdleWord | read-write | mandatory | The word used to stuff the payload of the ATM idle cell |
| 1.3.6.1.4.1.277.1.4.2.1.62 | ColumnpportAtmDisCardMode | read-write | mandatory | The desired clock source backup if the card is set in external clock source mode |
| 1.3.6.1.4.1.277.1.4.2.1.63 | ColumnpportAtmLastUnconfiguredVpi | read-only | mandatory | This entry holds the Vpi read from the last Unconfigured atm cell received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.64 | ColumnpportAtmLastUnconfiguredVci | read-only | mandatory | This entry holds the Vci read from the last Unconfigured atm cell received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.65 | ColumnpportAtmUnconfiguredCells | read-only | mandatory | This entry holds a count of the number of Unconfigured ATM cells received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.66 | ColumnpportAtmNumBitsVCI | read-only | mandatory | This entry holds a count of the VCI bits supppoted my this ATM card. |
| 1.3.6.1.4.1.277.1.4.2.1.67 | ColumnpportAtmNumBitsVPI | read-only | mandatory | This entry holds a count of the VPI bits supppoted my this ATM card. |
| 1.3.6.1.4.1.277.1.4.2.1.68 | ColumnpportAtmInterfaceType | read-write | mandatory | Integer used to set ATM UNI or NNI type |
| 1.3.6.1.4.1.277.1.4.2.1.69 | ColumnpportSonetSDHLoopbackConfig | read-write | mandatory | Integer used to set the loopback state of the Sonet/SDH port |
| 1.3.6.1.4.1.277.1.4.2.1.70 | ColumnpportSonetSDHLoopStatus | read-only | mandatory | Integer indicating the current loopback status of the Sonet/SDH port |
| 1.3.6.1.4.1.277.1.4.2.1.71 | ColumnpportOutDiscardsCell | read-only | mandatory | The total number of outbound cell discarded due to congestion. |
| 1.3.6.1.4.1.277.1.4.2.1.72 | ColumnpportAtmPlcp | read-write | mandatory | The PLCP maintains the state of the ATM Physical Layer Convergence Protocol. When the protocol is disabled atm direct mapping is used with hec cell delineation. |
| 1.3.6.1.4.1.277.1.4.2.1.73 | ColumnpportCbrTargetClockMode | read-write | mandatory | The clocking method to be used by the CBR card. 4-port CBR card 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive clock method |
| 1.3.6.1.4.1.277.1.4.2.1.74 | ColumnpportCbrCurrentClockMode | read-only | mandatory | The clocking method currently used by the CBR card. 4-port CBR card 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive clock method |
| 1.3.6.1.4.1.277.1.4.2.1.75 | ColumnpportClockMasterChannel | read-write | mandatory | The number of the channel (lport) on this pport that is used as ACM/SRTS master for this line interface: 4-port CBR E1/DS1 card (structured mode): 1..4 |
| 1.3.6.1.4.1.277.1.4.2.1.76 | ColumnpportFibreType | read-only | mandatory | The type of fibre connected to the ATM-IWU. Its type determines the maximum transmission distance. 1-port ATM-IWU STM-1/STS-3c card 4 - multimode fibre (maximu… |
| 1.3.6.1.4.1.277.1.4.2.1.77 | ColumnpportLaserStatus | read-write | mandatory | The configured state of the laser: 1-port ATM-IWU STM-1/STS-3c card & Topaz 4-port OC3 & STM-1 card 1 - off 2 - on |
| 1.3.6.1.4.1.277.1.4.2.1.78 | ColumnpportMaxActiveVpiBits | read-write | mandatory | The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges … |
| 1.3.6.1.4.1.277.1.4.2.1.79 | ColumnpportBipErrorsThresh | read-write | mandatory | The threshold of BIP errors. If the number of line BIP-24/8 rrors persists to exceed this value, the pport will be taken down and a trap will be issued: 1-port… |
| 1.3.6.1.4.1.277.1.4.2.1.80 | ColumnpportBipSectionErrors | read-only | mandatory | The number of B1 section BIP-8 errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.81 | ColumnpportBipLineErrors | read-only | mandatory | The number of line BIP-24/8 errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.82 | ColumnpportBipPathErrors | read-only | mandatory | The number of B3 path BIP-8 errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.83 | ColumnpportFebeErrors | read-only | mandatory | The number of line Far End Block Errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.84 | ColumnpportHcsErrors | read-only | mandatory | The number of correctable HCS errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.85 | ColumnpportHcsSevereErrors | read-only | mandatory | The number of uncorrectable HCS errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.86 | ColumnpportCongestedReceivedCells | read-only | mandatory | The number of received cells that were discarded due to congestion of the ATM-IWU, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.87 | ColumnpportCongestedTransmittedCells | read-only | mandatory | The number of cells to be transmitted, that were discarded due to congestion of the ATM-IWU, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.88 | ColumnpportAtmLayerErroredReceivedCells | read-only | mandatory | The number of received cells that were discarded due to ATM layer errors, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.89 | ColumnpportAtmLayerErroredTransmittedCells | read-only | mandatory | The number of cells to be transmitted, that were discarded due to ATM layer errors, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.90 | ColumnpportDS0BitStuff | read-write | mandatory | Bit stuffing on or off for 2047 bit pattern in DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.91 | ColumnpportDS0BitErrorCount | read-only | mandatory | Total number of errors in 2047 DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.92 | ColumnpportDS0BitErrorFreeSeconds | read-only | mandatory | Total number of error free seconds in 2047 DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.93 | ColumnpportDS0BitErroredSeconds | read-only | mandatory | Total number of errored seconds in 2047 DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.94 | ColumnpportDS0MidspanRepeaters | read-write | mandatory | Number of Midspan repeaters in a link to be punched thru for DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.95 | ColumnpportDS0TestPatternSync | read-only | mandatory | While DS0 far end testing, the DS0 pattern has detected the pattern four consecutive times. If the pattern is lost, this variable will be equal to one. |
| 1.3.6.1.4.1.277.1.4.2.1.96 | ColumnpportDS0InjectBitError | read-write | mandatory | While testing DS0 far end lpbk, setting this variable will inject a bit error into the test pattern. |
| 1.3.6.1.4.1.277.1.4.2.1.97 | ColumnpportDS0FarendLpbkType | read-write | mandatory | The type of DS0 equipment to be looped back at the far end during DS0 far end testing. 1 - OCU 2 - DSU 3 - CSU. |
| 1.3.6.1.4.1.277.1.4.2.1.98 | ColumnpportDS0LpbkMode | read-write | mandatory | This determines what mode the DS0 Processor will be set to. 1 - no lpbk 2 - switch lpbk 3 - far end lpbk. |
| 1.3.6.1.4.1.277.1.4.2.1.99 | ColumnpportDS0SwitchLpbkStart | read-write | mandatory | This is the first DS0 in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopback. If it's set to far end lo… |
| 1.3.6.1.4.1.277.1.4.2.1.100 | ColumnpportDS0SwitchLpbkEnd | read-write | mandatory | This is the Last DS0, +1, in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopback. If the DS0 processor … |
| 1.3.6.1.4.1.277.1.4.2.1.101 | ColumnpportDS0FarendDS0InLpbk | read-only | mandatory | This indicates the DS0 in far end loopback. |
| 1.3.6.1.4.1.277.1.4.2.1.102 | ColumnpportDS0SendTestTraffic | read-write | mandatory | Enable or Disable sending DS0 2047 test pattern for DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.103 | ColumnpportOc3LoopConfig | read-write | mandatory | The loopback state of the ATM IWU OC3 |
| 1.3.6.1.4.1.277.1.4.2.1.104 | ColumnpportOc3LoopStatus | read-only | mandatory | The current loopback status of the ATM IWU OC3 |
| 1.3.6.1.4.1.277.1.4.2.1.105 | ColumnpportISDNIpBaseAddr | read-write | mandatory | Specifies the base address used for IP Dynamic Address Assignment |
| 1.3.6.1.4.1.277.1.4.2.1.106 | ColumnpportSonetSTM1Scramble | read-write | mandatory | Configured SONET/STM-1 scrambling. |
| 1.3.6.1.4.1.277.1.4.2.1.107 | ColumnpportEFCIMarking | read-write | mandatory | Configured EFCI marking for cell traffic in Topaz IOMs |
| 1.3.6.1.4.1.277.1.4.2.1.108 | ColumnpportAtmQOSTransmitMode | read-write | mandatory | Select fix priority or weighted round-robin for cell transmission in different ATM QOS classes. |
| 1.3.6.1.4.1.277.1.4.2.1.109 | ColumnpportHECMode | read-write | mandatory | Configured ATM HEC single bit error correction routine. |
| 1.3.6.1.4.1.277.1.4.2.1.110 | ColumnpportISDNChannelStatus | read-only | mandatory | The ISDN call status of all the B-Channels on the pport are encoded into this 24 character, (for T1 ISDN PRI card...23B+D) or 31 character, (for E1 ISDN PRI ca… |
| 1.3.6.1.4.1.277.1.4.2.1.111 | Columnpportds1FarEndLoopStatus | read-write | mandatory | DS1 Far End Loopback Status as commanded by the switch |
| 1.3.6.1.4.1.277.1.4.2.1.112 | Columnpportds1FDLControl | read-write | mandatory | Enables or Disables FDL Function for DS1 ESF pport |
| 1.3.6.1.4.1.277.1.4.2.1.113 | Columnpportds1FDLPrmXmit | read-write | mandatory | Enables or Disables transmission of Performance Monitoring Report (PRM) messages on the DS1 ESF FDL |
| 1.3.6.1.4.1.277.1.4.2.1.114 | Columnpportds1FDLPidXmit | read-write | mandatory | Enables or Disables transmission of Path ID (PID) messages on the DS1 ESF FDL |
| 1.3.6.1.4.1.277.1.4.2.1.115 | Columnpportds1FDLXmitPid | read-write | mandatory | Transmit Path Id to be sent on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.116 | Columnpportds1FDLRcvPid | read-only | mandatory | The last path id message received on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.117 | Columnpportds1FDLRcvTsid | read-write | mandatory | The last test id message received on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.118 | ColumnpportSonetSDHFramingMode | read-write | mandatory | The Framing mode for SONET/SDH port interface types. |
| 1.3.6.1.4.1.277.1.4.2.1.119 | Columnpportds1InbandLoopType | read-write | mandatory | Integer used to distinguish Inband Line loopback code sent from the switch when commanding inband line loopbacks, and reckognized by the switch when responding… |
| 1.3.6.1.4.1.277.1.4.2.1.120 | ColumnpportESFDataLinkStatus | read-only | mandatory | The current status of the DS1 ESF (FDL) data link. |
| 1.3.6.1.4.1.277.1.4.2.1.121 | ColumnpportPMTcaId | read-write | mandatory | This object identifies the the most recently declared pport threshold crossing alert |
| 1.3.6.1.4.1.277.1.4.2.1.122 | ColumnpportBchanTimerValue | read-write | mandatory | This value is used on a per port basis to add a delay to answering a ISDN call of the initial Disconnect from the network. This due to the ARP cache not updati… |
| 1.3.6.1.4.1.277.1.4.2.1.123 | ColumnpportAAL5CRC32Error | read-only | mandatory | Number of received AAL5 packets with CRC32 errors. |
| 1.3.6.1.4.1.277.1.4.2.1.124 | ColumnpportAAL5CPIError | read-only | mandatory | Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros |
| 1.3.6.1.4.1.277.1.4.2.1.125 | ColumnpportAAL5LengthError | read-only | mandatory | Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - length value in trailer > 55 by… |
| 1.3.6.1.4.1.277.1.4.2.1.126 | ColumnpportAAL5ReassemblyTimerError | read-only | mandatory | Number of expired reassembly timers |
| 1.3.6.1.4.1.277.1.4.2.1.127 | ColumnpportAAL5MaxNrSegError | read-only | mandatory | Number of received AAL5 packets which exceeds the maximum allowed length |
| 1.3.6.1.4.1.277.1.4.2.1.128 | ColumnpportRedundancyArch | read-write | mandatory | Pport redundancy architecture. Default is disabled. aps-intracard aps-with-resilient-uni cards, resilient UNI is used to reroute traffic. aps-intercard-trunk-b… |
| 1.3.6.1.4.1.277.1.4.2.1.129 | ColumnpportAPSadminDir | read-write | mandatory | Provisioned APS switch-direction-mode. Default is uni- directional. |
| 1.3.6.1.4.1.277.1.4.2.1.130 | ColumnpportAPSlineType | read-write | mandatory | APS line type for the pport. Writable only when pportRedundancyArch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.131 | ColumnpportAPSrevertiveMode | read-write | mandatory | APS revertive mode. When revertive, after the condition for an automatic switchover clears, user traffic will be switched back to the working line after the pp… |
| 1.3.6.1.4.1.277.1.4.2.1.132 | ColumnpportAPSpairedSlotId | read-write | mandatory | Slot ID of the paired-with APS pport. Writable only when pportRedundancyArch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.133 | ColumnpportAPSpairedPportId | read-write | mandatory | Pport ID of the paired-with APS pport. Writable only when pportRedundancyARch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.134 | ColumnpportAPSsfBerThresh | read-write | mandatory | Exponent N for APS Signal Failure based on BER. A line bit-error-rate above 10^-N causes an SF BER failure to be asserted. SF BER is cleared when the line BER … |
| 1.3.6.1.4.1.277.1.4.2.1.135 | ColumnpportAPSsdBerThresh | read-write | mandatory | Exponent N for APS Signal Degrade based on BER. A line bit-error-rate above 10^-N causes an SD BER failure to be asserted. SD BER is cleared when the line BER … |
| 1.3.6.1.4.1.277.1.4.2.1.136 | ColumnpportAPSwtrPeriod | read-write | mandatory | APS wait-to-restore period. The number of minutes to wait after an automatic switch condition clears before switching back to the working line. |
| 1.3.6.1.4.1.277.1.4.2.1.137 | ColumnpportAPSprotectionLineState | read-only | mandatory | Indicates the state of the protection line selector. When selected, a protection switchover has taken place and user traffic is being selected from the protect… |
| 1.3.6.1.4.1.277.1.4.2.1.138 | ColumnpportAPSxCommand | read-write | mandatory | External switch commands. The clear command clears any previously activated external command. Manual switch is preemptable by auto-switch-requests (line failur… |
| 1.3.6.1.4.1.277.1.4.2.1.139 | ColumnpportAPSconfigStatus | read-only | mandatory | Status of APS pport configuration. The not-configured status indicates the pport APS feature is not configured or it is a non-APS pport. The valid state indica… |
| 1.3.6.1.4.1.277.1.4.2.1.140 | ColumnpportAPSOperRxStatus | read-only | mandatory | The current state of the pair of APS pports with respect to the ability of the pair to Receive user traffic. When indicated as up, user traffic may be received… |
| 1.3.6.1.4.1.277.1.4.2.1.141 | ColumnpportBertPattern | read-write | mandatory | Pattern generated by the XBERT |
| 1.3.6.1.4.1.277.1.4.2.1.142 | ColumnpportBertUserBytes | read-write | mandatory | Definition of 1,2,3 or 4 byte pattern if UserNByte selected. |
| 1.3.6.1.4.1.277.1.4.2.1.143 | ColumnpportBertErrorRate | read-write | mandatory | Error rate to insert in generated pattern. |
| 1.3.6.1.4.1.277.1.4.2.1.144 | ColumnpportBertCommand | read-write | mandatory | Single shot commands to the BERT. |
| 1.3.6.1.4.1.277.1.4.2.1.145 | ColumnpportBertStatus | read-only | mandatory | Current status of the BERT for this channel. |
| 1.3.6.1.4.1.277.1.4.2.1.146 | ColumnpportBertBitCount | read-only | mandatory | The number of bits received - stops counting at 0xFFFFFFFF |
| 1.3.6.1.4.1.277.1.4.2.1.147 | ColumnpportBertErrorCount | read-only | mandatory | The number of bits received in error- stops counting at 0xFFFFFFFF |
| 1.3.6.1.4.1.277.1.4.2.1.148 | Columnpportds1FELoopbackControl | read-write | mandatory | Enables or Disables Far end loopback control of the switch. Enabled (2) = Loop up and down commands from far end equipment will be processed. Disabled (1) - lo… |
| 1.3.6.1.4.1.277.1.4.2.1.149 | ColumnpportFT1DS0s | read-write | mandatory | DS0 usage bitmask for Fractional T1/E1 data rates. |
| 1.3.6.1.4.1.277.1.4.2.1.150 | ColumnpportIMUXCnt | read-write | mandatory | DS3 Inverse Multiplexer counter value - specifies number of idle cells to insert by the outbound process Hardware. |
| 1.3.6.1.4.1.277.1.4.2.1.151 | Columnpportds1PMConfigThresh | read-write | mandatory | The setting determines which standard is used for performance monitoring configuration thresholds |
| 1.3.6.1.4.1.277.1.4.2.1.152 | ColumnpportIdleCellType | read-write | mandatory | |
| 1.3.6.1.4.1.277.1.4.2.1.153 | ColumnpportATMTcaInHECErrorUAlertPeriod | read-write | mandatory | ATM tca ingress HEC error uncorrectable alert period (in min.). |
| 1.3.6.1.4.1.277.1.4.2.1.154 | ColumnpportATMTcaInHECErrorUThresh | read-write | mandatory | ATM tca ingress HEC error uncorrectable threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.155 | ColumnpportATMTcaEBufOverflowCBRAlertPeriod | read-write | mandatory | ATM tca egress buffer overflow CBR Alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.156 | ColumnpportATMTcaEBufOverflowCBRThresh | read-write | mandatory | ATM tca egress buffer overflow CBR threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.157 | ColumnpportATMTcaEBufOverflowABRAlertPeriod | read-write | mandatory | ATM tca egress buffer overflow ABR alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.158 | ColumnpportATMTcaEBufOverflowABRThresh | read-write | mandatory | ATM tca egress buffer overflow ABR threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.159 | ColumnpportATMTcaEBufOverflowVBR1AlertPeriod | read-write | mandatory | ATM tca egress buffer overflow VBR1 alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.160 | ColumnpportATMTcaEBufOverflowVBR1Thresh | read-write | mandatory | ATM tca egress buffer overflow VBR1 threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.161 | ColumnpportATMTcaEBufOverflowVBR2AlertPeriod | read-write | mandatory | ATM tca egress buffer overflow VBR2 alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.162 | ColumnpportATMTcaEBufOverflowVBR2Thresh | read-write | mandatory | ATM tca egress buffer overflow VBR2 threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.163 | ColumnpportATMTcaInFramerFIFOOverflowAlertPeriod | read-write | mandatory | ATM tca ingress framer FIFO overflow alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.164 | ColumnpportATMTcaInFramerFIFOOverflowThresh | read-write | mandatory | ATM tca ingress framer FIFO overflow threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.165 | ColumnpportATMTcaELookupFailureAlertPeriod | read-write | mandatory | ATM tca egress lookup failure alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.166 | ColumnpportATMTcaELookupFailureThresh | read-write | mandatory | ATM tca egress lookup failure threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.167 | ColumnpportATMTcaEnable | read-write | mandatory | ATM tca port enable. |
| 1.3.6.1.4.1.277.1.4.2.1.168 | ColumnpportATMTcaId | read-write | mandatory | This object identifies the the most recently declared pport ATM threshold crossing alert |
| 1.3.6.1.4.1.277.1.4.2.1.169 | ColumnpportFethAdminMacAddr | read-write | mandatory | The configured MAC address to use for this Fast Ethernet port. Setting this to all zeros will force the port to use the burned in MAC address. |
| 1.3.6.1.4.1.277.1.4.2.1.170 | ColumnpportFethOperMacAddr | read-only | mandatory | The actual MAC address in use for this Fast Ethernet port. |
| 1.3.6.1.4.1.277.1.4.2.1.171 | ColumnpportConfigAlarmSoakTime | read-write | mandatory | This is the soak time for configurable alarms. An alarm of this type must persist for this period before it is declared. The time is specified in millseconds u… |
| 1.3.6.1.4.1.277.1.4.2.1.172 | ColumnpportConfigAlarmClearTime | read-write | mandatory | This is the soak time for configurable alarms. An alarm of this type must remain clear for this period before it is declared to be cleared. The time is specifi… |
| 1.3.6.1.4.1.277.1.4.2.1.173 | ColumnpportFethPortCapability | read-write | mandatory | Selection for the speed (10/100) and mode (half/full duplex) of operation for Fast Ethernet ports. |
| 1.3.6.1.4.1.277.1.4.2.1.174 | ColumnpportVpshapingDiscardCellCount | read-only | mandatory | Cells discarded due to buffer overflow on this pport because of traffic shaping. |
| 1.3.6.1.4.1.277.1.4.3 | TablepportTrafficShaperTable | not-accessible | mandatory | A list of Parameters assigned to the 16 traffic shaper parameter conbinations of each pport of the ATM-IWU. |
| 1.3.6.1.4.1.277.1.4.3.1 | RowpportTrafficShaperEntry | not-accessible | mandatory | Information of a single system reference clock source. |
| 1.3.6.1.4.1.277.1.4.3.1.1 | ColumnpportTrafficShaperIndex | read-write | mandatory | A positive integer to identify an entry in the pportTrafficShaperTable. The ATM-IWU and CS cards support exactly 16 shapers. |
| 1.3.6.1.4.1.277.1.4.3.1.2 | ColumnpportTrafficShaperPriority | read-write | mandatory | The priority of the Shaper. Channels tied to a Shaper are served only if no higher priority Shapers await service. 0 ist the highest, 15 the lowest priority. |
| 1.3.6.1.4.1.277.1.4.3.1.3 | ColumnpportTrafficShaperCellRatioDividend | read-write | mandatory | The quotient of pportTrafficShaperCellRatioDividend and pportTrafficShaperCellRatioDivisor determines the average rate allocated to the shaper. The shaper serv… |
| 1.3.6.1.4.1.277.1.4.3.1.4 | ColumnpportTrafficShaperCellRatioDivisor | read-write | mandatory | See pportTrafficShaperCellRatioDividend |
| 1.3.6.1.4.1.277.1.4.3.1.5 | ColumnpportTrafficShaperPeak | read-write | mandatory | The peak cell rate. It defines the minimum gap (in cell units) between emission of any consecutive cells in this channel. |
| 1.3.6.1.4.1.277.1.4.3.1.6 | ColumnpportTrafficShaperCredit | read-write | mandatory | Defines the maximum number of credits that can be accumulated by a shaper. This is equivalent to the maximum burst allowed at the peak rate. |
| 1.3.6.1.4.1.277.1.5 | Nodelport | |||
| 1.3.6.1.4.1.277.1.5 | NodenodePsBStatusChange | This trap indicates that the power supply B has changed state (toggled between up and down states). | ||
| 1.3.6.1.4.1.277.1.5.1 | TablelportTable | not-accessible | mandatory | A list of logical port entries. The number of entries is given by the value of ifNumber in MIB-II. |
| 1.3.6.1.4.1.277.1.5.1.1 | RowlportEntry | not-accessible | mandatory | The logical port entry contains objects relevant to a logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.1 | ColumnlportIfIndex | read-only | mandatory | The ifIndex value of the corresponding ifEntry. |
| 1.3.6.1.4.1.277.1.5.1.1.2 | ColumnlportSlotId | read-only | mandatory | The slot number of the board the port is on. |
| 1.3.6.1.4.1.277.1.5.1.1.3 | ColumnlportPportId | read-only | mandatory | The physical port number of the interface on the board. |
| 1.3.6.1.4.1.277.1.5.1.1.4 | ColumnlportId | read-only | mandatory | The logical port number of the interface on the physical port. A logical port can be uniquely identified in a Cascade network as { NodeId.lportSlotId.lportPpor… |
| 1.3.6.1.4.1.277.1.5.1.1.5 | ColumnlportLink | read-write | mandatory | The equipment type of the peer to which the logical port is connected. |
| 1.3.6.1.4.1.277.1.5.1.1.6 | ColumnlportProtocol | read-write | mandatory | The data link protocol running on the logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.7 | ColumnlportSignal | read-write | mandatory | The user-network signalling capability for SVC and DLCMI of the logical port. Note that this only applies to fr protocol port. |
| 1.3.6.1.4.1.277.1.5.1.1.8 | ColumnlportFt1Ds0s | read-only | mandatory | The bit mask indicating the DS0s for the fractional T1/E1 logical port which must be a subset of the corresponding pportDs1Ds0s. It's represented by a 32-bit h… |
| 1.3.6.1.4.1.277.1.5.1.1.9 | ColumnlportGlobalDlci | read-write | mandatory | The global DLCI correspondent to the interface if the DLCI is globally significant in the network. Note that this object is read-write only during creation, an… |
| 1.3.6.1.4.1.277.1.5.1.1.10 | ColumnlportDlcmiStd | read-write | mandatory | This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface. |
| 1.3.6.1.4.1.277.1.5.1.1.11 | ColumnlportDlciAddrFmt | read-only | mandatory | This variable states which address format is in use on the Frame Relay interface. |
| 1.3.6.1.4.1.277.1.5.1.1.12 | ColumnlportDlciAddrLen | read-only | mandatory | This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address including the control po… |
| 1.3.6.1.4.1.277.1.5.1.1.13 | ColumnlportMaxFramesize | read-only | mandatory | The maximum frame size supported on the interface. Currently it's not used. |
| 1.3.6.1.4.1.277.1.5.1.1.14 | ColumnlportDceVerifTimer | read-write | mandatory | The polling verification timer (secs) on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll timer setti… |
| 1.3.6.1.4.1.277.1.5.1.1.15 | ColumnlportDceErrorThresh | read-write | mandatory | The error threshold on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll No Ack threshold setting. |
| 1.3.6.1.4.1.277.1.5.1.1.16 | ColumnlportDceEventCount | read-write | mandatory | The monitored events count on the DCE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.17 | ColumnlportDteErrorThresh | read-write | mandatory | The error threshold on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.18 | ColumnlportDteEventCount | read-write | mandatory | The monitored events count on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.19 | ColumnlportDtePollTimer | read-write | mandatory | The link status polling timer (secs) on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.20 | ColumnlportDteFullCounter | read-write | mandatory | The full status polling counter on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.21 | ColumnlportDteMulticast | read-only | mandatory | The multicast capability of the interface. |
| 1.3.6.1.4.1.277.1.5.1.1.22 | ColumnlportTrkRnode | read-write | mandatory | Node at the other end of the trunk. This object is read-write only during lport creation, and read-only thereafter. |
| 1.3.6.1.4.1.277.1.5.1.1.23 | ColumnlportTrkRlport | read-write | mandatory | Logical port (IfIndex) at the other end of the trunk. This |
| 1.3.6.1.4.1.277.1.5.1.1.24 | ColumnlportCongestState | read-only | mandatory | Congestion State for the logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.25 | ColumnlportQP1Len | read-only | mandatory | Priority-1 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.26 | ColumnlportQP2Len | read-only | mandatory | Priority-2 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.27 | ColumnlportQP3Len | read-only | mandatory | Priority-3 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.28 | ColumnlportQP4Len | read-only | mandatory | Priority-4 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.29 | ColumnlportErrTime | read-only | mandatory | The value of sysUpTime at which the last error was detected. |
| 1.3.6.1.4.1.277.1.5.1.1.30 | ColumnlportErrType | read-only | mandatory | The type of error that was last seen on this interface. |
| 1.3.6.1.4.1.277.1.5.1.1.31 | ColumnlportErrData | read-only | mandatory | An octet string containing as much of the error packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirabl… |
| 1.3.6.1.4.1.277.1.5.1.1.32 | ColumnlportDiagTestId | read-write | mandatory | Identification for the diagnostics tests to be run. |
| 1.3.6.1.4.1.277.1.5.1.1.33 | ColumnlportDiagTestRuns | read-write | mandatory | Number of passes of the diagnostics tests to be run. The default value is 1. |
| 1.3.6.1.4.1.277.1.5.1.1.34 | ColumnlportDataRate | read-write | mandatory | An estimate of the logical port's data rate in bits per second. |
| 1.3.6.1.4.1.277.1.5.1.1.35 | ColumnlportTrkStatus | read-only | mandatory | The current state of the trunk. The btdefined state only applies to backup trunks. |
| 1.3.6.1.4.1.277.1.5.1.1.36 | ColumnlportSevCongests | read-only | mandatory | The cumulative number of times that the lport's congestion state has changed from mildly-congested to severely-congested since the last reset. |
| 1.3.6.1.4.1.277.1.5.1.1.37 | ColumnlportAbsCongests | read-only | mandatory | The cumulative number of times that the lport's congestion state has changed from severely-congested to absolutely- congested since the last reset. |
| 1.3.6.1.4.1.277.1.5.1.1.38 | ColumnlportTrkOverhead | read-write | mandatory | An estimate of the overhead (headers and internal control messages) in trunking user data in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.39 | ColumnlportTrkUtil | read-write | mandatory | An estimate of the real utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.40 | ColumnlportVAvailbw | read-only | mandatory | Currently available virtual trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.41 | ColumnlportTrkLastTimeChange | read-only | mandatory | The sysUpTime value when the trunk was last changed to the current status. |
| 1.3.6.1.4.1.277.1.5.1.1.42 | ColumnlportCongestRate | read-only | mandatory | The rate (%) of entering severely or absolutely congested states in the last one minute interval. |
| 1.3.6.1.4.1.277.1.5.1.1.43 | ColumnlportCongestRateThresh | read-write | mandatory | The alert threshold (%) for the CongestRate; trap will be sent when exceeded. |
| 1.3.6.1.4.1.277.1.5.1.1.44 | ColumnlportDiagState | read-write | mandatory | The current state of the diagnostic on this logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.45 | ColumnlportDiagOptionStr | read-write | mandatory | Optional parameters to the diagnostic. |
| 1.3.6.1.4.1.277.1.5.1.1.46 | ColumnlportDiagPassCount | read-only | mandatory | Number of successful diagnostic passes. |
| 1.3.6.1.4.1.277.1.5.1.1.47 | ColumnlportDiagFailCount | read-only | mandatory | Number of failed diagnostic passes. |
| 1.3.6.1.4.1.277.1.5.1.1.48 | ColumnlportDiagResultStr | read-only | mandatory | Description of last diagnostic failure. |
| 1.3.6.1.4.1.277.1.5.1.1.49 | ColumnlportDs0BitStuff | read-write | mandatory | Is bit stuffing enabled on this lport? |
| 1.3.6.1.4.1.277.1.5.1.1.50 | ColumnlportErrorThreshold | read-write | mandatory | The per minute error threshold before a link error trap is sent. |
| 1.3.6.1.4.1.277.1.5.1.1.51 | ColumnlportUnsyncBandwidth | read-only | mandatory | The accumulated allocated/deallocated bandwidth which has not been propagated by OSPF yet. |
| 1.3.6.1.4.1.277.1.5.1.1.52 | ColumnlportDTEInStatusFrames | read-only | mandatory | The number of LMI STATUS frames received from the DCE since the last system reset. The count includes link integrity verification frames only. |
| 1.3.6.1.4.1.277.1.5.1.1.53 | ColumnlportDTEInFullStatusFrames | read-only | mandatory | The number of LMI Full STATUS frames received from the DTE since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.54 | ColumnlportDTEInAsyncStatusFrames | read-only | mandatory | The number of asynchronous LMI Status frames received from the DTE since the last system reset. For LMI Rev 1, these are Update STATUS frames. For ANSI Annex D… |
| 1.3.6.1.4.1.277.1.5.1.1.55 | ColumnlportDTEInErrorFrames | read-only | mandatory | The number of LMI frames received containing protocol errors. |
| 1.3.6.1.4.1.277.1.5.1.1.56 | ColumnlportDTEOutPollFrames | read-only | mandatory | The number of LMI Status Enquiry frames transmitted since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.57 | ColumnlportDTEPollErrorCounts | read-only | mandatory | The number of DTE in-channel signaling link reliability errors (i.e. LMI Status Enquiry frames that were not responded to, sequence number errors) since the la… |
| 1.3.6.1.4.1.277.1.5.1.1.58 | ColumnlportDTEFailCounts | read-only | mandatory | The number of times since the last system reset LMI has declared the DTE side of the link down due to excessive errors. |
| 1.3.6.1.4.1.277.1.5.1.1.59 | ColumnlportDTEFailReason | read-only | mandatory | The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent error. |
| 1.3.6.1.4.1.277.1.5.1.1.60 | ColumnlportDTEOperStatus | read-only | mandatory | The operational status of the DTE side of LMI on this link. |
| 1.3.6.1.4.1.277.1.5.1.1.61 | ColumnlportDCEInPollFrames | read-only | mandatory | The number of LMI poll frames received from the DTE since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.62 | ColumnlportDCEInErrorFrames | read-only | mandatory | The number of LMI frames received containing protocol errors. |
| 1.3.6.1.4.1.277.1.5.1.1.63 | ColumnlportDCEOutStatusFrames | read-only | mandatory | The number of LMI STATUS frames transmitted since the last system reset. The count includes link integrity verification frames only. |
| 1.3.6.1.4.1.277.1.5.1.1.64 | ColumnlportDCEOutFullStatusFrames | read-only | mandatory | The number of LMI Full STATUS frames transmitted since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.65 | ColumnlportDCEOutAsyncStatusFrames | read-only | mandatory | The number of asynchronous LMI Status frames transmitted since the last system reset. For LMI Rev 1, these are Update STATUS frames. For ANSI Annex D and CCITT… |
| 1.3.6.1.4.1.277.1.5.1.1.66 | ColumnlportDCEPollErrorCounts | read-only | mandatory | The number of DCE in-channel signaling link reliability errors (i.e. timeouts waiting for LMI Status Enquiry frames, sequence number errors) since the last sys… |
| 1.3.6.1.4.1.277.1.5.1.1.67 | ColumnlportDCEFailCounts | read-only | mandatory | The number of times since the last system reset LMI has declared the DCE side of the link down due to excessive errors. |
| 1.3.6.1.4.1.277.1.5.1.1.68 | ColumnlportDCEFailReason | read-only | mandatory | The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent error. |
| 1.3.6.1.4.1.277.1.5.1.1.69 | ColumnlportDCEOperStatus | read-only | mandatory | The operational status of the DCE side of LMI on this link. |
| 1.3.6.1.4.1.277.1.5.1.1.70 | ColumnlportDCEOperDlcmiStd | read-only | mandatory | This variable states which Data Link Connection Management scheme is actually being run on this link. This is used for DCE links configured for AutoDetect and … |
| 1.3.6.1.4.1.277.1.5.1.1.71 | ColumnlportLMIInErrorFrames | read-only | mandatory | The number of total frames received with an error. For NNI links this is the sum of lportDTEInErrorFrames and lportDCEInErrorFrames. |
| 1.3.6.1.4.1.277.1.5.1.1.72 | ColumnlportDCEnN4 | read-write | mandatory | This variable specifies the maximum number of LMI Status Enquiry frames that can be received from a DTE within time interval lportDCEnT3. This is only valid on… |
| 1.3.6.1.4.1.277.1.5.1.1.73 | ColumnlportDCEnT3 | read-write | mandatory | This variable specifies the time interval (secs) used to determine if lportDCEnN4 an excess number (lportDCEnN4) of Status Enquiry messages are received. This … |
| 1.3.6.1.4.1.277.1.5.1.1.74 | ColumnlportXmitLatencyThreshold | read-write | mandatory | Outbound frames are allowed on the transmit commit queue when the commit queue falls below this threshold (in microseconds). |
| 1.3.6.1.4.1.277.1.5.1.1.75 | ColumnlportXmitRefillPriority0Percentage | read-write | mandatory | Percentage of time the transmit queue is refilled in priority order 0, 1, 2, 3. |
| 1.3.6.1.4.1.277.1.5.1.1.76 | ColumnlportXmitRefillPriority1Percentage | read-write | mandatory | Percentage of time the transmit queue is refilled in priority order 1, 2, 3, 0. |
| 1.3.6.1.4.1.277.1.5.1.1.77 | ColumnlportXmitRefillPriority2Percentage | read-write | mandatory | Percentage of time the transmit queue is refilled in priority order 2, 3, 0, 1. |
| 1.3.6.1.4.1.277.1.5.1.1.78 | ColumnlportXmitRefillPriority3Percentage | read-write | mandatory | Percentage of time the transmit queue is refilled in priority order 3, 0, 1, 2. |
| 1.3.6.1.4.1.277.1.5.1.1.79 | ColumnlportXmitDiscardLow | read-write | mandatory | Priority holding queue low water discard threshold. Discarding stops when holding queue hits this level. |
| 1.3.6.1.4.1.277.1.5.1.1.80 | ColumnlportSevereThreshold | read-write | mandatory | Severe congestion level. Outbound red and amber packets are discarded when the transmit queue hits this threshold. |
| 1.3.6.1.4.1.277.1.5.1.1.81 | ColumnlportMildThreshold | read-write | mandatory | Mild congestion level. Outbound red packets are discarded when the transmit queue hits this threshold. |
| 1.3.6.1.4.1.277.1.5.1.1.86 | ColumnlportTrkKeepAliveTimer | read-write | mandatory | Send a keep-alive packet after this many seconds. These packets are sent on trunk links only. The range is 0 thru 15, with zero meaning the keep-alive protocol… |
| 1.3.6.1.4.1.277.1.5.1.1.87 | ColumnlportTrkKeepAliveErrorThreshold | read-write | mandatory | Declare the interface down after this many keep-alive packets in a row are missed. The default is five. |
| 1.3.6.1.4.1.277.1.5.1.1.88 | ColumnlportIgCutThruStatus | read-write | mandatory | Enable ingress cut-thru on this user lport. Default is disabled. |
| 1.3.6.1.4.1.277.1.5.1.1.89 | ColumnlportEgCutThruStatus | read-write | mandatory | Enable egress cut-thru on this user lport. Default is disabled. |
| 1.3.6.1.4.1.277.1.5.1.1.90 | ColumnlportEgCutThruThresh | read-write | mandatory | Egress cut thru threshold - start transmitting a frame on a user port after this many segments have arrived. |
| 1.3.6.1.4.1.277.1.5.1.1.91 | ColumnlportFrameRelayTrkEnable | read-write | mandatory | Allow Frame Relay Trunks on the user link. |
| 1.3.6.1.4.1.277.1.5.1.1.92 | ColumnlportSmdsSsiIf | read-write | mandatory | The interface number of the SSI which this DXI/SNI is multiplexed to. |
| 1.3.6.1.4.1.277.1.5.1.1.93 | ColumnlportSmdsSsiSlot | read-write | mandatory | The slot of the SSI which this DXI/SNI is multiplexed to. |
| 1.3.6.1.4.1.277.1.5.1.1.94 | ColumnlportSmdsScrnId | read-write | mandatory | The ID of address screen for this interface. |
| 1.3.6.1.4.1.277.1.5.1.1.95 | ColumnlportSmdsIaScrnOp | read-write | mandatory | Individual address screen operation. |
| 1.3.6.1.4.1.277.1.5.1.1.96 | ColumnlportSmdsGaScrnOp | read-write | mandatory | Group address screen operation. |
| 1.3.6.1.4.1.277.1.5.1.1.97 | ColumnlportSmdsIaScrnMap | read-write | mandatory | The individual address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit … |
| 1.3.6.1.4.1.277.1.5.1.1.98 | ColumnlportSmdsGaScrnMap | read-write | mandatory | The group address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. … |
| 1.3.6.1.4.1.277.1.5.1.1.99 | ColumnlportSmdsTrkAddr | read-write | mandatory | SMDS address. For SSI feeder port, this address is the local address of all SMDS optimim paths associated with this SSI feeder port. For SSI Optimum path port,… |
| 1.3.6.1.4.1.277.1.5.1.1.100 | ColumnlportSmdsCrc | read-write | mandatory | CRC which CPE generates. |
| 1.3.6.1.4.1.277.1.5.1.1.101 | ColumnlportSmdsCpePoll | read-write | mandatory | Whether CPE supports heart beat poll or not. |
| 1.3.6.1.4.1.277.1.5.1.1.102 | ColumnlportSmdsPduCheck | read-write | mandatory | turn of/off the detailed SIP3 PDU error checking. |
| 1.3.6.1.4.1.277.1.5.1.1.103 | ColumnlportSmdsCntOutFrDxi2HbPolls | read-write | mandatory | Number of DXI2 heart beat poll frames transmitted. |
| 1.3.6.1.4.1.277.1.5.1.1.104 | ColumnlportSmdsCntOutByteDxi2HbPolls | read-write | mandatory | Total number of octets in DXI2 heart beat poll frames transmitted. |
| 1.3.6.1.4.1.277.1.5.1.1.105 | ColumnlportSmdsCntInFrDxi2HbPolls | read-write | mandatory | Number of DXI2 heart beat poll frames received. |
| 1.3.6.1.4.1.277.1.5.1.1.106 | ColumnlportSmdsCntInByteDxi2HbPolls | read-write | mandatory | Total number of octets in DXI2 heart beat poll frames received. |
| 1.3.6.1.4.1.277.1.5.1.1.107 | ColumnlportSmdsCntOutFrSip3s | read-write | mandatory | Number of SIP3 frames transmitted. |
| 1.3.6.1.4.1.277.1.5.1.1.108 | ColumnlportSmdsCntOutByteSip3s | read-write | mandatory | Total number of octets in SIP3 frames transmitted. |
| 1.3.6.1.4.1.277.1.5.1.1.109 | ColumnlportSmdsCntInFrSip3s | read-write | mandatory | Number of SIP3 frames received. |
| 1.3.6.1.4.1.277.1.5.1.1.110 | ColumnlportSmdsCntInByteSip3s | read-write | mandatory | Total number of octets in SIP3 frames received. |
| 1.3.6.1.4.1.277.1.5.1.1.111 | ColumnlportSmdsCntDxi2LinkIdInvalids | read-write | mandatory | Number of instances that DXI2 link ID is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.112 | ColumnlportSmdsCntDxi2StationIdInvalids | read-write | mandatory | Number of instances that DXI2 station ID is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.113 | ColumnlportSmdsCntDxi2CrInvalids | read-write | mandatory | Number of instances that DXI2 command/response field is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.114 | ColumnlportSmdsCntDxi2AeInvalids | read-write | mandatory | Number of instances that DXI2 address extension field is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.115 | ColumnlportSmdsCntDxi2CtrlInvalids | read-write | mandatory | Number of instances that DXI2 control field is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.116 | ColumnlportSmdsCntDxi2FrameSizeErrors | read-write | mandatory | Number of instances there is a DXI2 frame size error. |
| 1.3.6.1.4.1.277.1.5.1.1.117 | ColumnlportSmdsCntSip3RsvdInvalids | read-write | mandatory | Number of instances that SIP3 reserved field in header is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.118 | ColumnlportSmdsCntSip3BetagMismatchs | read-write | mandatory | Number of instances that SIP3 BE tag is not macthed. |
| 1.3.6.1.4.1.277.1.5.1.1.119 | ColumnlportSmdsCntSip3BasizeIncorrects | read-write | mandatory | Number of instances that SIP3 BA size is incorrect. |
| 1.3.6.1.4.1.277.1.5.1.1.120 | ColumnlportSmdsCntSip3BasizeInvalids | read-write | mandatory | Number of instances that SIP3 BA size is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.121 | ColumnlportSmdsCntSip3DaTypeInvalids | read-write | mandatory | Number of instances that SIP3 destination address type is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.122 | ColumnlportSmdsCntSip3DaInvalids | read-write | mandatory | Number of instances that SIP3 destination address is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.123 | ColumnlportSmdsCntSip3SaTypeInvalids | read-write | mandatory | Number of instances that SIP3 source address type is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.124 | ColumnlportSmdsCntSip3SaInvalids | read-write | mandatory | Number of instances that SIP3 source address is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.125 | ColumnlportSmdsCntSip3BasizeMismatchs | read-write | mandatory | Number of instances that SIP3 BA sizes in the header and trailer are not matched. |
| 1.3.6.1.4.1.277.1.5.1.1.126 | ColumnlportSmdsCntSip3HeLenInvalids | read-write | mandatory | Number of instances that SIP3 header extension length is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.127 | ColumnlportSmdsCntSip3HeVersionInvalids | read-write | mandatory | Number of instances that SIP3 header extension version is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.128 | ColumnlportSmdsCntSip3HeCarrierInvalids | read-write | mandatory | Number of instances that SIP3 header extension carrier is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.129 | ColumnlportSmdsCntSip3Crc32Errors | read-write | mandatory | Number of SIP3 CRC errors. |
| 1.3.6.1.4.1.277.1.5.1.1.130 | ColumnlportSmdsCntSip3TRsvdInvalids | read-write | mandatory | Number of instances that SIP3 reserved field in trailer is invalid. |
| 1.3.6.1.4.1.277.1.5.1.1.131 | ColumnlportSmdsCntSaNotFounds | read-write | mandatory | Number of instances that source address not found. |
| 1.3.6.1.4.1.277.1.5.1.1.132 | ColumnlportSmdsCntSaValidationFails | read-write | mandatory | Number of instances that source address validation failed. |
| 1.3.6.1.4.1.277.1.5.1.1.133 | ColumnlportSmdsCntSaDaOnSamePorts | read-write | mandatory | Number of instances that source address and destination addresses are on the same port. |
| 1.3.6.1.4.1.277.1.5.1.1.134 | ColumnlportSmdsCntDaSsiMismacths | read-write | mandatory | Obsolete. |
| 1.3.6.1.4.1.277.1.5.1.1.135 | ColumnlportSmdsCntSsiProvisionErrors | read-write | mandatory | Obsolete. |
| 1.3.6.1.4.1.277.1.5.1.1.136 | ColumnlportSmdsCntDstIaNotFounds | read-write | mandatory | Number of instances that destination individual address not found. |
| 1.3.6.1.4.1.277.1.5.1.1.137 | ColumnlportSmdsCntDstGaNotFounds | read-write | mandatory | Number of instances that destination group address not found. |
| 1.3.6.1.4.1.277.1.5.1.1.138 | ColumnlportSmdsCntSrcIaScrnFails | read-write | mandatory | Number of instances that source individual address screening failed. |
| 1.3.6.1.4.1.277.1.5.1.1.139 | ColumnlportSmdsCntDstIaScrnFails | read-write | mandatory | Number of instances that destination individual address screening failed. |
| 1.3.6.1.4.1.277.1.5.1.1.140 | ColumnlportSmdsCntDstGaScrnFails | read-write | mandatory | Number of instances that destination group address screening failed. |
| 1.3.6.1.4.1.277.1.5.1.1.141 | ColumnlportSmdsTotalDiscards | read-write | mandatory | total number of discards. |
| 1.3.6.1.4.1.277.1.5.1.1.142 | ColumnlportSmdsSsiNode | read-write | mandatory | The Node of the SSI which this DXI/SNI is multiplexed to. |
| 1.3.6.1.4.1.277.1.5.1.1.143 | ColumnlportBilling | read-write | mandatory | This object defines the ability to enable and disable billing on this logical port (for SMDS this must be a DXI). When the value of nodeBilling is 'enabled', t… |
| 1.3.6.1.4.1.277.1.5.1.1.144 | ColumnlportSmdsReserved144 | read-write | mandatory | reserved! ignore! |
| 1.3.6.1.4.1.277.1.5.1.1.145 | ColumnlportLinkStatus | read-write | mandatory | Link protocol status. The Link protocol may be frame relay LMI, DXI heart beat poll, PPP LCP, etc, depends on the lport type. |
| 1.3.6.1.4.1.277.1.5.1.1.146 | ColumnlportLMIDelay | read-write | mandatory | The number of seconds 1-9 to buffer (or initiate) a FR LMI async update (or ATM OAM alarms) to allow filtering of LMI async events. Zero (0) indicates that no … |
| 1.3.6.1.4.1.277.1.5.1.1.147 | ColumnlportCRC | read-write | mandatory | Lport CRC selection: 0 - 16 bit CRC 1 - 32 bit CRC |
| 1.3.6.1.4.1.277.1.5.1.1.148 | ColumnlportSmdsMulticastGa | read-write | mandatory | The Multicast Group Address is the smds broadcast address which is used to get smds address from its IP address. |
| 1.3.6.1.4.1.277.1.5.1.1.149 | ColumnlportSmdsMulticastIpAddr | read-write | mandatory | This IP address is this logical port's IP address. |
| 1.3.6.1.4.1.277.1.5.1.1.150 | ColumnlportAtmVPI | read-write | mandatory | VPI value in the ATM cell header: ATM DXI with HSSI IOP VPI (4 lsb bit) range: 0 - 15 ATM UNI DS3/E3 IOP VPI (4 lsb bit) range: 0 - 15 |
| 1.3.6.1.4.1.277.1.5.1.1.151 | ColumnlportAtmVCI | read-write | mandatory | VCI value in the ATM cell header: ATM DXI with HSSI IOP VCI (6 lsb bit) range: 0 - 63 ATM UNI DS3/E3 IOP VCI (8 lsb bit) range: 0 - 255 |
| 1.3.6.1.4.1.277.1.5.1.1.152 | ColumnlportPeakCellRateindex | read-write | mandatory | Peak cell rate queue index |
| 1.3.6.1.4.1.277.1.5.1.1.153 | ColumnlportSustCellRate | read-write | mandatory | Sustainable cell rate in cell/second |
| 1.3.6.1.4.1.277.1.5.1.1.154 | ColumnlportBurstTolerance | read-write | mandatory | Burst Tolerance in multiple of 32 cells |
| 1.3.6.1.4.1.277.1.5.1.1.155 | ColumnlportBuTrkOnFailure | read-write | mandatory | Enables or disables trunk backup due to link down. |
| 1.3.6.1.4.1.277.1.5.1.1.156 | ColumnlportTrkFailureThrsh | read-write | mandatory | The number of seconds a primary trunk must remain down for trunk backup to be initiated. |
| 1.3.6.1.4.1.277.1.5.1.1.157 | ColumnlportTrkRestThrsh | read-write | mandatory | The number of seconds a primary trunk must remain up for trunk backup to be terminated |
| 1.3.6.1.4.1.277.1.5.1.1.158 | ColumnlportBuTrkRetryInt | read-write | mandatory | The number of seconds between backup trunk call setup retries. |
| 1.3.6.1.4.1.277.1.5.1.1.159 | ColumnlportBuTrkRetryNum | read-write | mandatory | The number of backup trunk call setup tries per call setup cycle. |
| 1.3.6.1.4.1.277.1.5.1.1.160 | ColumnlportBuTrkCycleInt | read-write | mandatory | The number of seconds between backup trunk call setup cycles. |
| 1.3.6.1.4.1.277.1.5.1.1.161 | ColumnlportTrkManualBu | read-write | mandatory | Initiate or terminate manual backup for a primary trunk. none neither initiate or terminate initCmd initiate operator commanded backup termCmd terminate operat… |
| 1.3.6.1.4.1.277.1.5.1.1.162 | ColumnlportPrimTrk | read-write | mandatory | Indicates the primary trunk lportIfIndex for which a backup trunk is serving as a backup. This value is also used to determine trunk type by the following conv… |
| 1.3.6.1.4.1.277.1.5.1.1.163 | ColumnlportInitCallSetup | read-write | mandatory | TRUE if node must initiate backup trunk call setup for this primary trunk. Otherwise FALSE. |
| 1.3.6.1.4.1.277.1.5.1.1.164 | ColumnlportBuFailReason | read-only | mandatory | Indicates the reason for the failure to perform trunk backup. |
| 1.3.6.1.4.1.277.1.5.1.1.165 | ColumnlportQ922Enable | read-write | mandatory | Set 1 to eanble Q.922 on this port. Q.922 must be enabled if the port is used for SVC. |
| 1.3.6.1.4.1.277.1.5.1.1.166 | ColumnlportQ922State | read-only | mandatory | Q.922 state. This object only makes sense when Q.922 is enabled. |
| 1.3.6.1.4.1.277.1.5.1.1.167 | ColumnlportTrkPduRevision | read-only | mandatory | The Trunk PDU Revision number being used over this trunk. |
| 1.3.6.1.4.1.277.1.5.1.1.168 | ColumnlportPVCMgrPduRevision | read-only | mandatory | The PVC Manager PDU Revision number being used over this trunk. |
| 1.3.6.1.4.1.277.1.5.1.1.169 | ColumnlportDS0LoopStatus | read-only | mandatory | Indicates whether this logical port has one or more DS0's in loopback |
| 1.3.6.1.4.1.277.1.5.1.1.170 | ColumnlportISDNDuration | read-only | mandatory | The number of seconds that the ISDN call has been established. |
| 1.3.6.1.4.1.277.1.5.1.1.171 | ColumnlportISDNSourceAddr | read-only | mandatory | The E.164 address of the source of this ISDN connection. |
| 1.3.6.1.4.1.277.1.5.1.1.172 | ColumnlportISDNDestAddr | read-only | mandatory | The E.164 address of the destination of this ISDN connection. |
| 1.3.6.1.4.1.277.1.5.1.1.173 | ColumnlportISDNIpAddr | read-only | mandatory | The Ip Address of the client connected to this B-Channel |
| 1.3.6.1.4.1.277.1.5.1.1.174 | ColumnlportISDNCallRejCause | read-only | mandatory | The cause of the call rejection - inability to authenticate or pool is busy. |
| 1.3.6.1.4.1.277.1.5.1.1.175 | ColumnlportLastInvalidDLCI | read-only | mandatory | This item pertains to user frame relay lports only. The frame relay header of the received frame contains a dlci, which uniquely identifies a specific pvc on t… |
| 1.3.6.1.4.1.277.1.5.1.1.176 | ColumnlportTrkProtState | read-only | mandatory | The current operational state of the link trunk protocol on this link. |
| 1.3.6.1.4.1.277.1.5.1.1.177 | ColumnlportTrkTrafficMix | read-write | mandatory | The types of traffic allowed over a Cascade trunk. |
| 1.3.6.1.4.1.277.1.5.1.1.178 | ColumnlportNumVC | read-only | mandatory | The number of VCs going to or through a particular port. |
| 1.3.6.1.4.1.277.1.5.1.1.179 | ColumnlportTrkAdminCost | read-write | mandatory | The administrative cost of the trunk. Used when routing circuits. Trunks with lower costs are preferred. Value ranges from 1 to 65,535. |
| 1.3.6.1.4.1.277.1.5.1.1.180 | ColumnlportPrivateNet | read-write | mandatory | If non-zero, indicates the private network that the lport belongs to. If 0, the lport is publicly shared. |
| 1.3.6.1.4.1.277.1.5.1.1.181 | ColumnlportTrkStaticDelay | read-write | mandatory | The measured round-trip delay of the trunk, in milliseconds. Measured when the trunk last became operational. |
| 1.3.6.1.4.1.277.1.5.1.1.182 | ColumnlportTrkDynamicDelay | read-write | mandatory | The recently measured round-tip delay of the trunk. May vary from lportTrkStaticDelay due to congestion, or reprovisioning of the underlying media. |
| 1.3.6.1.4.1.277.1.5.1.1.183 | ColumnlportAtmDataRateQoS1 | read-write | mandatory | An estimate of the logical port's data rate in bits per second reserved for QoS class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.184 | ColumnlportAtmDataRateQoS2 | read-write | mandatory | An estimate of the logical port's data rate in bits per second reserved for QoS class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.185 | ColumnlportAtmDataRateQoS3 | read-write | mandatory | An estimate of the logical port's data rate in bits per second reserved for QoS class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.186 | ColumnlportAtmDataRateQoS4 | read-write | mandatory | An estimate of the logical port's data rate in bits per second reserved for QoS class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.187 | ColumnlportOutVAvailbwQoS1 | read-only | mandatory | Current outgoing available virtual bandwidth reserved for QoS class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.188 | ColumnlportOutVAvailbwQoS2 | read-only | mandatory | Current outgoing available virtual bandwidth reserved for QoS class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.189 | ColumnlportOutVAvailbwQoS3 | read-only | mandatory | Current outgoing available virtual bandwidth reserved for QoS class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.190 | ColumnlportOutVAvailbwQoS4 | read-only | mandatory | Current outgoing available virtual bandwidth reserved for QoS class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.191 | ColumnlportInVAvailbwQoS1 | read-only | mandatory | Current incoming available virtual bandwidth reserved for QoS class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.192 | ColumnlportInVAvailbwQoS2 | read-only | mandatory | Current incoming available virtual bandwidth reserved for QoS class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.193 | ColumnlportInVAvailbwQoS3 | read-only | mandatory | Current incoming available virtual bandwidth reserved for QoS class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.194 | ColumnlportInVAvailbwQoS4 | read-only | mandatory | Currently incoming available virtual bandwidth reserved for QoS class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.195 | ColumnlportOutAllocbwQoS1 | read-only | mandatory | Current outgoing allocated bandwidth for QoS Class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.196 | ColumnlportOutAllocbwQoS2 | read-only | mandatory | Current outgoing allocated bandwidth for QoS Class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.197 | ColumnlportOutAllocbwQoS3 | read-only | mandatory | Current outgoing allocated bandwidth for QoS Class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.198 | ColumnlportOutAllocbwQoS4 | read-only | mandatory | Current outgoing allocated bandwidth for QoS Class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.199 | ColumnlportInAllocbwQoS1 | read-only | mandatory | Current incoming allocated bandwidth for QoS Class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.200 | ColumnlportInAllocbwQoS2 | read-only | mandatory | Current incoming allocated bandwidth for QoS Class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.201 | ColumnlportInAllocbwQoS3 | read-only | mandatory | Current incoming allocated bandwidth for QoS Class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.202 | ColumnlportInAllocbwQoS4 | read-only | mandatory | Current incoming allocated bandwidth for QoS Class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.203 | ColumnlportDynamicQoSbw | read-write | mandatory | Bitmap defining which QoS Classes should have bandwidth allocated dynamically from lportDataRate instead of reserving a percentage up-front. |
| 1.3.6.1.4.1.277.1.5.1.1.204 | ColumnlportSVCRetryTimer | read-write | mandatory | The duration in seconds (1..255) the network is allowed to re-establish a SVC after network failure before clearing the SVC. A value of (0) indicates continuou… |
| 1.3.6.1.4.1.277.1.5.1.1.205 | ColumnlportAtmNetworkType | read-write | mandatory | Whether this lport is supporting a private or public network. |
| 1.3.6.1.4.1.277.1.5.1.1.206 | ColumnlportAtmRouteMetricQoS1 | read-write | mandatory | Routing metric associated with QoS Class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.207 | ColumnlportAtmRouteMetricQoS2 | read-write | mandatory | Routing metric associated with QoS Class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.208 | ColumnlportAtmRouteMetricQoS3 | read-write | mandatory | Routing metric associated with QoS Class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.209 | ColumnlportAtmRouteMetricQoS4 | read-write | mandatory | Routing metric associated with QoS Class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.210 | ColumnlportIlmiPollTimeout | read-write | mandatory | The duration in seconds (1..255) the ILMI poll is generated by the network-side UME. A value of 0 set to default polling period of 5 seconds. |
| 1.3.6.1.4.1.277.1.5.1.1.211 | ColumnlportAtmProtocol | read-write | mandatory | UNI protocol version for this port. |
| 1.3.6.1.4.1.277.1.5.1.1.212 | ColumnlportIlmiAdminStatus | read-write | mandatory | Administrative state for ILMI function on this port. |
| 1.3.6.1.4.1.277.1.5.1.1.213 | ColumnlportIlmiOperStatus | read-only | mandatory | Operational status for ILMI function on this port. |
| 1.3.6.1.4.1.277.1.5.1.1.214 | ColumnlportIlmiPollRetry | read-write | mandatory | The number of retries of ILMI poll request will be generated when network-side UME detects loss of ILMI connectivity. A value of 0 sets to default value of 4 t… |
| 1.3.6.1.4.1.277.1.5.1.1.215 | ColumnlportAtmVpiBits | read-write | mandatory | Number of bits of VPI supported. |
| 1.3.6.1.4.1.277.1.5.1.1.216 | ColumnlportAtmVciBits | read-write | mandatory | Number of bits of VCI supported. |
| 1.3.6.1.4.1.277.1.5.1.1.217 | ColumnlportAtmOamAlarmEnable | read-write | mandatory | If disabled then OAM alarms are not generated for circuits that are down on this lport. |
| 1.3.6.1.4.1.277.1.5.1.1.218 | ColumnlportInVAvailbw | read-only | mandatory | Currently available Incoming virtual bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.219 | ColumnlportbwUNIPolicy | read-write | mandatory | The network policy towards requiring sufficient bandwidth at the UNI interface prior to allowing a circuit to be established. |
| 1.3.6.1.4.1.277.1.5.1.1.220 | ColumnlportStarvation | read-only | mandatory | The CBR card detected a starvation condition on this lport for the extended period defined in Bellcore TA-NWT-001248 |
| 1.3.6.1.4.1.277.1.5.1.1.221 | ColumnlportRecOverflow | read-only | mandatory | The CBR card detected a receive overflow condition on this lport for the extended period defined in Bellcore TA-NWT-001248 |
| 1.3.6.1.4.1.277.1.5.1.1.222 | ColumnlportLossOfCellSequence | read-only | mandatory | The CBR card detected a LOS condition on this lport for the extended period defined in Bellcore TA-NWT-001248 |
| 1.3.6.1.4.1.277.1.5.1.1.223 | ColumnlportLossOfStructurePointer | read-only | mandatory | The CBR card detected a loss of structure pointer condition on this lport for the extended period defined in Bellcore TA-NWT-001248 |
| 1.3.6.1.4.1.277.1.5.1.1.224 | ColumnlportCbrInsDummyCells | read-only | mandatory | The number of dummy cells inserted due to cell loss on a constant bit rate (AAL1) interface. |
| 1.3.6.1.4.1.277.1.5.1.1.225 | ColumnlportRecFifoUnderflowCnt | read-only | mandatory | The number of receive FIFO underflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the lportStarvation. |
| 1.3.6.1.4.1.277.1.5.1.1.226 | ColumnlportRecFifoOverflowCnt | read-only | mandatory | The number of receive FIFO overflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the receive FIFO overf… |
| 1.3.6.1.4.1.277.1.5.1.1.227 | ColumnlportCbrLossOfStructurePointerCnt | read-only | mandatory | The object counts how often the structured CBR card detected a loss of the structure pointer since the last reset. |
| 1.3.6.1.4.1.277.1.5.1.1.228 | ColumnlportCbrLossOfCellSequenceCnt | read-only | mandatory | The number of loss of cell sequence since the last reset. |
| 1.3.6.1.4.1.277.1.5.1.1.229 | ColumnlportShaperId | read-write | mandatory | The shaper to be used for this ATM trunk interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card Values: 1..16 |
| 1.3.6.1.4.1.277.1.5.1.1.230 | ColumnlportIlmiPrefixScreenMode | read-write | mandatory | The type of screening to apply against dynamic prefixes received from the peer ILMI entity at this DTE port. |
| 1.3.6.1.4.1.277.1.5.1.1.231 | ColumnlportSmdsPduViolTca | read-write | mandatory | This object defines the ability to enable and disable SMDS pdu violation traps on this logical port. This functionality applies to the following logical port t… |
| 1.3.6.1.4.1.277.1.5.1.1.232 | ColumnlportSmdsPduViolThresh | read-write | mandatory | This object defines the Smds pdu violation threshold for this logical port. The allowable range of threshold values is 1-255. The default value of this object … |
| 1.3.6.1.4.1.277.1.5.1.1.233 | ColumnlportSmdsPduHdrSip3SaNotFound | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Not Found. The first 8 bytes of t… |
| 1.3.6.1.4.1.277.1.5.1.1.234 | ColumnlportSmdsPduHdrSip3SaDaOnSamePort | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Da On Same Port. The first 8 byte… |
| 1.3.6.1.4.1.277.1.5.1.1.235 | ColumnlportSmdsPduHdrSip3DstGaNotFound | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga Not Found. The first 8 bytes … |
| 1.3.6.1.4.1.277.1.5.1.1.236 | ColumnlportSmdsPduHdrSip3DstIaScrnFail | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia Scrn Fail. The first 8 bytes … |
| 1.3.6.1.4.1.277.1.5.1.1.237 | ColumnlportSmdsPduHdrSip3SaValFail | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Val Fail. The first 8 bytes of th… |
| 1.3.6.1.4.1.277.1.5.1.1.238 | ColumnlportSmdsPduHdrSip3DstIaNotFound | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia Not Found. The first 8 bytes … |
| 1.3.6.1.4.1.277.1.5.1.1.239 | ColumnlportSmdsPduHdrSip3SrcIaScrnFail | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Src Ia Scrn Fail. The first 8 bytes … |
| 1.3.6.1.4.1.277.1.5.1.1.240 | ColumnlportSmdsPduHdrSip3DstGaScrnFail | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga Scrn Fail. The first 8 bytes … |
| 1.3.6.1.4.1.277.1.5.1.1.241 | ColumnlportSmdsPduHdrSip3SaTypeInvalid | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Type Invalid. The first 8 bytes o… |
| 1.3.6.1.4.1.277.1.5.1.1.242 | ColumnlportSmdsPduHdrSip3DaTypeInvalid | read-only | mandatory | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Da Type Invalid. The first 8 bytes o… |
| 1.3.6.1.4.1.277.1.5.1.1.243 | ColumnlportSmdsPduHdrDxi2LinkIdInvalid | read-only | mandatory | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Link Id Invalid. The length of this object is 4 bytes. |
| 1.3.6.1.4.1.277.1.5.1.1.244 | ColumnlportSmdsPduHdrDxi2CrInvalid | read-only | mandatory | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Cr Invalid. The length of this object is 4 bytes. |
| 1.3.6.1.4.1.277.1.5.1.1.245 | ColumnlportSmdsPduHdrDxi2CtrlInvalid | read-only | mandatory | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ctrl Invalid. The length of this object is 4 bytes. |
| 1.3.6.1.4.1.277.1.5.1.1.246 | ColumnlportSmdsPduHdrDxi2StationIdInvalid | read-only | mandatory | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Station Id Invalid. The length of this object is 4 bytes. |
| 1.3.6.1.4.1.277.1.5.1.1.247 | ColumnlportSmdsPduHdrDxi2AeInvalid | read-only | mandatory | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ae Invalid. The length of this object is 4 bytes. |
| 1.3.6.1.4.1.277.1.5.1.1.248 | ColumnlportDS0FarendLpbkEnabled | read-write | mandatory | Set a single DS0 into farend loopback 1-24. |
| 1.3.6.1.4.1.277.1.5.1.1.249 | ColumnlportDS0FarendLpbkDisabled | read-write | mandatory | Set a single DS0 out farend loopback 1-24. |
| 1.3.6.1.4.1.277.1.5.1.1.250 | ColumnlportTrkProtFailureThreshold | read-write | mandatory | The time, measured in seconds, that Trunk Protocol waits before transitioning the state of an unresponsive trunk from UP to DOWN. Trunk protocol keepalive requ… |
| 1.3.6.1.4.1.277.1.5.1.1.251 | ColumnlportPtr | read-only | mandatory | An octet string indicating the lport pointer. |
| 1.3.6.1.4.1.277.1.5.1.1.252 | ColumnlportISDNPoolUtil | read-only | mandatory | The percent utilization of the B-channel pool that this b-channel belongs to. |
| 1.3.6.1.4.1.277.1.5.1.1.253 | ColumnlportISDNIpAddrAssignFail | read-only | mandatory | The cause value for why Ip Address assignment has failed. |
| 1.3.6.1.4.1.277.1.5.1.1.254 | ColumnlportTrkUtilQoS1 | read-write | mandatory | An estimate of the real QoS1 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.255 | ColumnlportTrkUtilQoS2 | read-write | mandatory | An estimate of the real QoS2 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.256 | ColumnlportTrkUtilQoS3 | read-write | mandatory | An estimate of the real QoS3 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.257 | ColumnlportTrkUtilQoS4 | read-write | mandatory | An estimate of the real QoS4 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.267 | ColumnlportInCells | read-only | mandatory | The total number of cells received |
| 1.3.6.1.4.1.277.1.5.1.1.268 | ColumnlportOutCells | read-only | mandatory | The total number of cells transmitted |
| 1.3.6.1.4.1.277.1.6 | Nodeckt | |||
| 1.3.6.1.4.1.277.1.6 | NodenodeFanStatusChange | This trap indicates that a fan has changed state (toggled between up and down states). | ||
| 1.3.6.1.4.1.277.1.6.1 | TablecktTable | not-accessible | mandatory | A table containing information about specific DLCIs, channels and corresponding circuits. |
| 1.3.6.1.4.1.277.1.6.1.1 | RowcktEntry | not-accessible | mandatory | The information regarding a single Data Link Connection Identifier. |
| 1.3.6.1.4.1.277.1.6.1.1.1 | ColumncktSrcIfIndex | read-only | mandatory | The ifIndex value of the corresponding ifEntry. |
| 1.3.6.1.4.1.277.1.6.1.1.2 | ColumncktSrcDlci | read-only | mandatory | The DLCI used as the key for the circuit. For local DLCI significance, this is the local DLCI. For Global DLCI significance, this is the remote DLCI. |
| 1.3.6.1.4.1.277.1.6.1.1.3 | ColumncktPriority | read-write | mandatory | The priority level (1 through 3) for this circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.4 | ColumncktCir | read-write | mandatory | The average number of user data (bits) that the network agrees to transfer over the circuit in one direction, measured over the measurement interval T = cktBc/… |
| 1.3.6.1.4.1.277.1.6.1.1.5 | ColumncktBc | read-write | mandatory | The maximum amount of data (bits) that the network agrees to transfer over the circuit under normal conditions, during the measurement interval. |
| 1.3.6.1.4.1.277.1.6.1.1.6 | ColumncktBe | read-write | mandatory | The maximum amount of uncommitted data (bits) that the network will attempt to transfer over the circuit during the measurement interval. By default, if not co… |
| 1.3.6.1.4.1.277.1.6.1.1.7 | ColumncktDestNodeId | read-write | mandatory | The destination node ID for this circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.8 | ColumncktDestIfIndex | read-write | mandatory | The interface identifier at the destination node for this circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.9 | ColumncktDestDlci | read-write | mandatory | The DLCI which is the destination of the key DLCI. For local DLCI significance, this is the remote DLCI since the key DLCI is the local DLCI. For global signif… |
| 1.3.6.1.4.1.277.1.6.1.1.10 | ColumncktTos | read-only | mandatory | The type of service for the circuit. Only committed is supported in the FCS. |
| 1.3.6.1.4.1.277.1.6.1.1.11 | ColumncktOde | read-write | mandatory | This variable states whether graceful discard is enabled for the ckt. |
| 1.3.6.1.4.1.277.1.6.1.1.12 | ColumncktAdminStatus | read-write | mandatory | The desired state of the ckt. |
| 1.3.6.1.4.1.277.1.6.1.1.13 | ColumncktCreationTime | read-only | mandatory | The value of sysUpTime when the circuit was created (activated). |
| 1.3.6.1.4.1.277.1.6.1.1.14 | ColumncktLastTimeChange | read-only | mandatory | The sysUpTime value when the circuit was last changed to the current state. |
| 1.3.6.1.4.1.277.1.6.1.1.15 | ColumncktVcState | read-only | mandatory | The current state of the PVC segment in the Cascade network. |
| 1.3.6.1.4.1.277.1.6.1.1.16 | ColumncktDceState | read-only | mandatory | The DCE state of the circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.17 | ColumncktDteStatus | read-only | mandatory | The DTE status of the circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.18 | ColumncktRnr | read-only | mandatory | The receiver's readiness for accepting data flow. |
| 1.3.6.1.4.1.277.1.6.1.1.19 | ColumncktNiDown | read-only | mandatory | The state of the network interface. |
| 1.3.6.1.4.1.277.1.6.1.1.20 | ColumncktDteState | read-only | mandatory | The DTE state of the circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.21 | ColumncktOperStatus | read-only | mandatory | The current operational status of the entire PVC. |
| 1.3.6.1.4.1.277.1.6.1.1.22 | ColumncktOutForward | read-only | mandatory | If the value is 1, it means the outbound flow is on. |
| 1.3.6.1.4.1.277.1.6.1.1.23 | ColumncktRerouteCnt | read-only | mandatory | The reroute count. |
| 1.3.6.1.4.1.277.1.6.1.1.24 | ColumncktVcPtr | read-only | mandatory | An 8-byte Octect string indicating the vc pointer. |
| 1.3.6.1.4.1.277.1.6.1.1.25 | ColumncktHopCnt | read-only | mandatory | The count of hops along the circuit path. (Max is 16) |
| 1.3.6.1.4.1.277.1.6.1.1.26 | ColumncktPath | read-only | mandatory | The circuit path consisting a sequence of outbound interface indexes at nodes along the established circuit. The format is interface:interface:interface...... |
| 1.3.6.1.4.1.277.1.6.1.1.27 | ColumncktFailReason | read-only | mandatory | The reason for the PVC establishment failure. |
| 1.3.6.1.4.1.277.1.6.1.1.28 | ColumncktFailNode | read-only | mandatory | The node which causes the PVC failure. |
| 1.3.6.1.4.1.277.1.6.1.1.29 | ColumncktFailPort | read-only | mandatory | The port on the fail node which causes the PVC failure. |
| 1.3.6.1.4.1.277.1.6.1.1.30 | ColumncktMcastGroupId | read-write | mandatory | Multicast group identifier (1..32). This field is 0 for unicast PVCs. |
| 1.3.6.1.4.1.277.1.6.1.1.31 | ColumncktMcastMemberList | read-write | mandatory | A list of operations and the affected unicast DLCIs (lportId, cktId)s in a multicast group. The syntax is as follows: [op:dlci,dlci,...,op:dlci,dlci,...] where… |
| 1.3.6.1.4.1.277.1.6.1.1.32 | ColumncktMcastParentGroups | read-only | mandatory | An 8-byte Octect string indicating the parent groups this DLCI belongs to. |
| 1.3.6.1.4.1.277.1.6.1.1.33 | ColumncktInFrames | read-only | mandatory | The number of inbound frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.34 | ColumncktInDEFrames | read-only | mandatory | The number of inbound DE-marked frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.35 | ColumncktInODEFrames | read-only | mandatory | The number of inbound ODE-marked frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.36 | ColumncktInFECNFrames | read-only | mandatory | The number of inbound frames indicating forward congestion since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.37 | ColumncktInBECNFrames | read-only | mandatory | The number of inbound frames indicating backward congestion since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.38 | ColumncktInDiscards | read-only | mandatory | Number of inbound frames discarded by rate enforcement. |
| 1.3.6.1.4.1.277.1.6.1.1.39 | ColumncktInOctets | read-only | mandatory | The number of inbound octets since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.40 | ColumncktInDEOctets | read-only | mandatory | The number of inbound DE-marked octets since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.41 | ColumncktInODEOctets | read-only | mandatory | The number of inbound ODE-marked octets since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.42 | ColumncktOutFrames | read-only | mandatory | The number of outbound frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.43 | ColumncktOutDEFrames | read-only | mandatory | The number of outbound DE-marked frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.44 | ColumncktOutODEFrames | read-only | mandatory | The number of outbound ODE-marked frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.45 | ColumncktOutFECNFrames | read-only | mandatory | The number of outbound FECN-marked frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.46 | ColumncktOutBECNFrames | read-only | mandatory | The number of outbound BECN-marked frames since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.47 | ColumncktOutOctets | read-only | mandatory | The number of outbound octets since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.48 | ColumncktOutDEOctets | read-only | mandatory | The number of outbound DE-marked octets since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.49 | ColumncktOutODEOctets | read-only | mandatory | The number of outbound ODE-marked octets since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.50 | ColumncktOutLostFrames | read-only | mandatory | The number of outbound frames that have been lost since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.51 | ColumncktOutLostDEFrames | read-only | mandatory | The number of outbound DE-marked frames that have been lost since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.52 | ColumncktOutLostODEFrames | read-only | mandatory | The number of outbound ODE-marked frames that have been lost since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.53 | ColumncktOutLostOctets | read-only | mandatory | The number of outbound octets that have been lost since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.54 | ColumncktOutLostDEOctets | read-only | mandatory | The number of outbound DE-marked octets that have been lost since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.55 | ColumncktOutLostODEOctets | read-only | mandatory | The number of outbound ODE-marked octets that have been lost since the last reset. |
| 1.3.6.1.4.1.277.1.6.1.1.56 | ColumncktRtMinDelay | read-only | mandatory | The minimum round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.57 | ColumncktRtMaxDelay | read-only | mandatory | The maximum round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.58 | ColumncktRtAvgDelay | read-only | mandatory | The average round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.59 | ColumncktDiagTestId | read-write | mandatory | Identification for the diagnostics tests to be run. |
| 1.3.6.1.4.1.277.1.6.1.1.60 | ColumncktDiagTestRuns | read-write | mandatory | Number of passes of the diagnostics tests to be run. The default value is 1. |
| 1.3.6.1.4.1.277.1.6.1.1.61 | ColumncktHelloCounter | read-only | mandatory | Number of PVC hello pdu frames received in the VC entry of the called side. |
| 1.3.6.1.4.1.277.1.6.1.1.62 | ColumncktHelloAckCounter | read-only | mandatory | Number of PVC hello Ack pdu frames received in the VC entry of the calling side. |
| 1.3.6.1.4.1.277.1.6.1.1.63 | ColumncktDefinedPath | read-write | mandatory | User defined path. in the format of Nx,x,x,Nx,.... If x is not prefixed with 'N', x is an interface ID. If x is prefixed with `N`, x is a node ID. |
| 1.3.6.1.4.1.277.1.6.1.1.64 | ColumncktDefinedPathCount | read-only | mandatory | User defined path hop count. |
| 1.3.6.1.4.1.277.1.6.1.1.65 | ColumncktDefinedPathEnable | read-write | mandatory | If set to 1, it means there is an user defined path for this circuit and it is enabled. |
| 1.3.6.1.4.1.277.1.6.1.1.66 | ColumncktDefinedPathAltOption | read-write | mandatory | If set to 1, it means that if the user defined path fails, use the ospf-determined path. |
| 1.3.6.1.4.1.277.1.6.1.1.67 | ColumncktUsingDefinedPath | read-only | mandatory | If set to 1, it indicates the PVC is currently using the defined path. |
| 1.3.6.1.4.1.277.1.6.1.1.68 | ColumncktTryAltPath | read-only | mandatory | If set to 1, it means the inactive PVC will be activated on the ospf-determined path in the next retry. |
| 1.3.6.1.4.1.277.1.6.1.1.69 | ColumncktNotVirgin | read-only | mandatory | If set to 1, it means this VC entry has been successfuly activated before. |
| 1.3.6.1.4.1.277.1.6.1.1.70 | ColumncktInForward | read-only | mandatory | If the value is 1, it means the inbound flow is OK. |
| 1.3.6.1.4.1.277.1.6.1.1.71 | ColumncktBtusSeg | read-write | mandatory | Number of Bus xmit units per data segment |
| 1.3.6.1.4.1.277.1.6.1.1.72 | ColumncktInSegmentsDiscards | read-only | mandatory | Number of segments received that were discarded because of frame reassembly errors. |
| 1.3.6.1.4.1.277.1.6.1.1.73 | ColumncktAtmVPI | read-write | mandatory | VPI value in the ATM cell header: ATM DXI with HSSI IOP VPI (4 lsb bit) range: 0 - 15 ATM UNI DS3/E3 IOP VPI (4 lsb bit) range: 0 - 15 T1 ATM 4 lsb range 0-15 … |
| 1.3.6.1.4.1.277.1.6.1.1.74 | ColumncktAtmVCI | read-write | mandatory | VCI value in the ATM cell header: ATM DXI with HSSI IOP VCI (6 lsb bit) range: 0 - 63 ATM UNI DS3/E3 IOP VCI (8 lsb bit) range: 0 - 255 T1 ATM 4 lsb VCI (6 lsb… |
| 1.3.6.1.4.1.277.1.6.1.1.75 | ColumncktType | read-only | mandatory | 1 if a permanent virtual circuit; 2 if a switched virtual circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.76 | ColumncktSvcCallingParty | read-only | mandatory | The calling party number if this is a switched virtual circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.77 | ColumncktSvcCalledParty | read-only | mandatory | The called party number if this is a switched virtual circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.78 | ColumncktSvcDuration | read-only | mandatory | The duration since the SVC circuit has been running. |
| 1.3.6.1.4.1.277.1.6.1.1.79 | ColumncktSvcCause | read-only | mandatory | SVC cause number. The index will be 0.0 and should be disregarded. The following cause numbers maybe returned by stdx: 1 - unassigned number, callee is not ass… |
| 1.3.6.1.4.1.277.1.6.1.1.80 | ColumncktXlatFlag | read-write | mandatory | 0 if RFC1490 or no translation; 1 if RFC1483 translation. |
| 1.3.6.1.4.1.277.1.6.1.1.81 | ColumncktDestLaddr | read-write | mandatory | The destination logical address of the circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.82 | ColumncktSrcLaddr | read-write | mandatory | The source logical address of the circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.83 | ColumncktLoop | read-write | mandatory | Setting this variable controls the loopback status of the given circuit endpoint. |
| 1.3.6.1.4.1.277.1.6.1.1.84 | ColumncktRerouteBalance | read-write | mandatory | Setting this variable controls the use of rerouting to balance link usage. |
| 1.3.6.1.4.1.277.1.6.1.1.85 | ColumncktCallingBackup | read-only | mandatory | Indicates if a caller endpoint is calling a backup PVC. |
| 1.3.6.1.4.1.277.1.6.1.1.86 | ColumncktRCir | read-write | mandatory | The average number of user data (bits) that the network agrees to transfer over the circuit in the opposite direction, measured over the measurement interval T… |
| 1.3.6.1.4.1.277.1.6.1.1.87 | ColumncktAtmQoS | read-write | mandatory | The Quality of Service of the ATM Circuit. Valid only for ATM type circuits. |
| 1.3.6.1.4.1.277.1.6.1.1.88 | ColumncktAtmInCells | read-only | mandatory | The Number of ATM cells received on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.89 | ColumncktAtmOutCells | read-only | mandatory | The Number of ATM cells transmitted on a VC (VPC or VCC).. |
| 1.3.6.1.4.1.277.1.6.1.1.90 | ColumncktAtmInDiscardedClp0Cells | read-only | mandatory | The Number of ATM CLP0 cells received and discarded on a VC (VPC or VCC).. |
| 1.3.6.1.4.1.277.1.6.1.1.91 | ColumncktAtmInDiscardedClp1Cells | read-only | mandatory | The Number of ATM CLP1 cells received and discarded on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.92 | ColumncktAtmVcType | read-write | mandatory | Type of ATM connection (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.93 | ColumncktAtmPCR | read-write | mandatory | The Peak Cell Rate measured in cells/second at which cells are transmitted for this circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.94 | ColumncktAtmSCR | read-write | mandatory | The Sustainable Cell Rate is the average transmission rate in cells per second for this circuit. It must be less than or or equal to the Peak Cell Rate. |
| 1.3.6.1.4.1.277.1.6.1.1.95 | ColumncktAtmMBS | read-write | mandatory | The Maximum Burst size determines the maximum number of cells that can be transmitted at the peak cell rate. |
| 1.3.6.1.4.1.277.1.6.1.1.96 | ColumncktAtmInPassedClp0Cells | read-only | mandatory | The Number of ATM CLP 0 cells received and passed UPC on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.97 | ColumncktAtmInPassedClp1Cells | read-only | mandatory | The Number of ATM CLP 1 cells received and passed UPC on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.98 | ColumncktAtmInTaggedCells | read-only | mandatory | The Number of ATM cells received and tagged on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.99 | ColumncktAtmOutClp0Cells | read-only | mandatory | The Number of ATM CLP 0 cells transmitted on a VC (VPC or VCC).. |
| 1.3.6.1.4.1.277.1.6.1.1.100 | ColumncktAtmOutClp1Cells | read-only | mandatory | The Number of ATM CLP 1 cells transmitted on a VC (VPC or VCC).. |
| 1.3.6.1.4.1.277.1.6.1.1.101 | ColumncktAtmRQoS | read-write | mandatory | The Quality of Service of the ATM connection in the opposite direction. |
| 1.3.6.1.4.1.277.1.6.1.1.102 | ColumncktAtmTfdType | read-write | mandatory | The combination of traffic parameters. |
| 1.3.6.1.4.1.277.1.6.1.1.103 | ColumncktAtmRTfdType | read-write | mandatory | The combination of traffic parameters in opposite direction. |
| 1.3.6.1.4.1.277.1.6.1.1.104 | ColumncktAtmTfdParam1 | read-write | mandatory | The traffic descriptor parameter 1. |
| 1.3.6.1.4.1.277.1.6.1.1.105 | ColumncktAtmTfdParam2 | read-write | mandatory | The traffic descriptor parameter 2. |
| 1.3.6.1.4.1.277.1.6.1.1.106 | ColumncktAtmTfdParam3 | read-write | mandatory | The traffic descriptor parameter 3. |
| 1.3.6.1.4.1.277.1.6.1.1.107 | ColumncktAtmRTfdParam1 | read-write | mandatory | The traffic descriptor parameter 1 for opposite direction. |
| 1.3.6.1.4.1.277.1.6.1.1.108 | ColumncktAtmRTfdParam2 | read-write | mandatory | The traffic descriptor parameter 3 for opposite direction. |
| 1.3.6.1.4.1.277.1.6.1.1.109 | ColumncktAtmRTfdParam3 | read-write | mandatory | The traffic descriptor parameter 3 for opposite direction. |
| 1.3.6.1.4.1.277.1.6.1.1.110 | ColumncktAtmFrameIWF | read-write | mandatory | Frame Relay/ATM Interworking Function indicator. |
| 1.3.6.1.4.1.277.1.6.1.1.111 | ColumncktAtmUserPlane | read-write | mandatory | Bitmap defining user plane capabilities. |
| 1.3.6.1.4.1.277.1.6.1.1.112 | ColumncktRBc | read-write | mandatory | The maximum amount of data (bits) that the network agrees to transfer over the circuit in the opposite direction under normal conditions, during the measuremen… |
| 1.3.6.1.4.1.277.1.6.1.1.113 | ColumncktRBe | read-write | mandatory | The maximum amount of uncommitted data (bits) that the network will attempt to transfer over the circuit in the opposite direction during the measurement inter… |
| 1.3.6.1.4.1.277.1.6.1.1.114 | ColumncktOamLoopbackDirection | read-write | mandatory | Which direction to send the loopback cell. If 'local', send out this circuit entry's port. If 'remote', send out the remote circuit entry's port. |
| 1.3.6.1.4.1.277.1.6.1.1.115 | ColumncktOamLoopbackType | read-write | mandatory | Type of oam loopback to send - either segment or end to end. |
| 1.3.6.1.4.1.277.1.6.1.1.116 | ColumncktOamLoopbackHops | read-write | mandatory | Number of hops the loopback cell should traverse inside the Cascade network before being echoed back by the far Cascade device. |
| 1.3.6.1.4.1.277.1.6.1.1.117 | ColumncktOamLoopbackCount | read-write | mandatory | Number of oam loopback cells left to send this session. Setting this from zero to non-zero starts the loopback session. |
| 1.3.6.1.4.1.277.1.6.1.1.118 | ColumncktOamLoopbackReceived | read-only | mandatory | Number of oam responses received for this loopback session. |
| 1.3.6.1.4.1.277.1.6.1.1.119 | ColumncktOamLoopbackTimeouts | read-only | mandatory | Number of times a loopback response was not received within the timeout period during this loopback session. |
| 1.3.6.1.4.1.277.1.6.1.1.120 | ColumncktOamLoopbackReceivedHigh | read-only | mandatory | Highest response time (in milliseconds) of an oam loopback response this loopback session. |
| 1.3.6.1.4.1.277.1.6.1.1.121 | ColumncktOamLoopbackReceivedLow | read-only | mandatory | Lowest response time (in milliseconds) of an oam loopback response this loopback session. |
| 1.3.6.1.4.1.277.1.6.1.1.122 | ColumncktOamLoopbackReceivedAvg | read-only | mandatory | Average response time (in milliseconds) of an oam loopback response this loopback session. |
| 1.3.6.1.4.1.277.1.6.1.1.123 | ColumncktOamAlarmDisable | read-write | mandatory | If disabled, then don't generate oam alarms if this circuit is down. |
| 1.3.6.1.4.1.277.1.6.1.1.124 | ColumncktShaperId | read-write | mandatory | The shaper to be used for this virtual connection interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card Values: 1..16 |
| 1.3.6.1.4.1.277.1.6.1.1.125 | ColumncktOspfCtd | read-write | mandatory | The allowed cell delay: 4-port CBR E1/DS1 card The maximum allowed cell delay in msec |
| 1.3.6.1.4.1.277.1.6.1.1.126 | ColumncktOspfCdv | read-write | mandatory | The allowed cell delay variation: 4-port CBR E1/DS1 card The maximum allowed cell delay variation in msec |
| 1.3.6.1.4.1.277.1.6.1.1.127 | ColumncktOutPort | read-only | mandatory | The outgoing port number for the adjacent VC entry in this switch. |
| 1.3.6.1.4.1.277.1.6.1.1.128 | ColumncktOutVc | read-only | mandatory | The adjacent VC entry corresponding to this circuit accross the bus. |
| 1.3.6.1.4.1.277.1.6.1.1.129 | ColumncktRVc | read-only | mandatory | The adjacent VC entry corresponding to this circuit accross the trunk. |
| 1.3.6.1.4.1.277.1.6.1.1.130 | ColumncktEntryType | read-only | mandatory | The internal type of circuit entry allocated by the circuit manager. |
| 1.3.6.1.4.1.277.1.6.1.1.131 | ColumncktDiagStr | read-only | mandatory | Internal diagnostic information. |
| 1.3.6.1.4.1.277.1.6.1.1.132 | ColumncktSvcAalType | read-only | mandatory | The AAL type for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.133 | ColumncktSvcBBearerClass | read-only | mandatory | The Broadband bearer capability class for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.134 | ColumncktSvcBBearerClippingSusc | read-only | mandatory | The Broadband bearer capability clipping susceptibility for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.135 | ColumncktSvcBBearerTmgReq | read-only | mandatory | The Broadband bearer capability timing requirements for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.136 | ColumncktSvcBBearerTfcType | read-only | mandatory | The Broadband bearer capability traffic type for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.137 | ColumncktAtmUPCEnable | read-write | mandatory | Enable ATM UPC Function. |
| 1.3.6.1.4.1.277.1.6.1.1.138 | ColumncktRPriority | read-write | mandatory | The priority level (0 through 3) for this circuit in the opposite direction. When port service type is defined as 'mono-class', this priority means the forward… |
| 1.3.6.1.4.1.277.1.6.1.1.139 | ColumncktRtPriority | read-write | mandatory | The routing priority level of the circuit which is a 8 bit number where the 3-bit bumping priority is contained in bits 0-2 and the 4-bit bandwidth priority is… |
| 1.3.6.1.4.1.277.1.6.1.1.140 | ColumncktDeltaBc | read-write | mandatory | The maximum number of bits that the network agree to transfer over the circuit as committed bits during the measurement interval under the CONDITION that the c… |
| 1.3.6.1.4.1.277.1.6.1.1.141 | ColumncktDeltaBe | read-write | mandatory | The maximum number of bits that the network agree to transfer over the circuit as allowed excess bits during the measurement interval under the CONDITION that … |
| 1.3.6.1.4.1.277.1.6.1.1.142 | ColumncktDeltaRBc | read-write | mandatory | The maximum number of bits that the network agree to transfer over the circuit as committed bits in the opposite direction during the measurement interval unde… |
| 1.3.6.1.4.1.277.1.6.1.1.143 | ColumncktDeltaRBe | read-write | mandatory | The maximum number of bits that the network agree to transfer over the circuit as allowed excess bits in the opposite direction during the measurement interval… |
| 1.3.6.1.4.1.277.1.6.1.1.144 | ColumncktRedFrPcnt | read-write | mandatory | The percentage of RED frame bits that are allowed to enter the network, during the measurement interval, under non-congestion condition. Its value range is 0 -… |
| 1.3.6.1.4.1.277.1.6.1.1.145 | ColumncktRedFrRPcnt | read-write | mandatory | The percentage of RED frame bits that are allowed to enter the network in the opposite direction, during the measurement interval, under non-congestion conditi… |
| 1.3.6.1.4.1.277.1.6.1.1.146 | ColumncktRateEnforceSchm | read-write | mandatory | Variable used to indicate the rate enforcement scheme employed. 0: Slide window rate enforcement scheme 1: Jump window rate enforcement scheme 2: Simple rate e… |
| 1.3.6.1.4.1.277.1.6.1.1.147 | ColumncktRateEnforceRSchm | read-write | mandatory | Variable used to indicate the rate enforcement scheme employed in the opposite direction. 0: Slide window rate enforcement scheme 1: Jump window rate enforceme… |
| 1.3.6.1.4.1.277.1.6.1.1.148 | ColumncktROde | read-write | mandatory | This variable states whether graceful discard is enabled for the ckt in the opposite direction. |
| 1.3.6.1.4.1.277.1.6.1.1.149 | ColumncktPrivateNet | read-write | mandatory | If non-zero, indicates the private network that the circuit belongs to. If 0, the circuit has access to the entire public portion of the network. |
| 1.3.6.1.4.1.277.1.6.1.1.150 | ColumncktPrivateNetOverflow | read-write | mandatory | Indicates how private network circuits are handled, when the resources of the network have become exhausted. If set to use-public, the resources of the public … |
| 1.3.6.1.4.1.277.1.6.1.1.151 | ColumncktCustomerID | read-write | mandatory | The Customer that owns this circuit. For Virtual Private Networking Support. |
| 1.3.6.1.4.1.277.1.6.1.1.152 | ColumncktAtmCDVT | read-write | mandatory | The Cell Delay Variation Tolerance for the VC |
| 1.3.6.1.4.1.277.1.6.1.1.153 | ColumncktNdcEnable | read-write | mandatory | Enable/disable Network Data Collection for a PVC on an IOM. The number of NDC-monitored PVCs is limited as follows: 30 per DS3 interface, 90 per OC3 interface,… |
| 1.3.6.1.4.1.277.1.6.1.1.154 | ColumncktInterworkingFrToAtmCLP | read-write | mandatory | CLP mapping for Frame Relay To ATM Service Interworking. |
| 1.3.6.1.4.1.277.1.6.1.1.155 | ColumncktInterworkingFrToAtmDe | read-write | mandatory | DE bit mapping for ATM To Frame Relay Service Interworking. |
| 1.3.6.1.4.1.277.1.6.1.1.156 | ColumncktNrtsCLP1 | read-write | mandatory | Whether to use the discard threshold as the CLP1 Discard threshold upon reception of a cell by the NRTS processor in the forward direction. |
| 1.3.6.1.4.1.277.1.6.1.1.157 | ColumncktNrtsDiscardClp0 | read-only | mandatory | The number of the CLP0 cells received and discarded by the NRTS processor. |
| 1.3.6.1.4.1.277.1.6.1.1.158 | ColumncktNrtsDiscardClp1 | read-only | mandatory | The number of the CLP1 cells received and discarded by the NRTS processor. |
| 1.3.6.1.4.1.277.1.6.1.1.159 | ColumncktMPEnableAMF | read-write | mandatory | Whether the Multilink PPP PVC Attributes Modification Feature is enabled. |
| 1.3.6.1.4.1.277.1.6.1.1.160 | ColumncktMPEligible | read-write | mandatory | Whether this circuit is eligible to be a member of a Multilink PPP bundle. |
| 1.3.6.1.4.1.277.1.6.1.1.161 | ColumncktMPForcedCaller | read-write | mandatory | Whether this end of the circuit has been forced to be caller to support Multilink PPP PVC Attributes Modification Feature. |
| 1.3.6.1.4.1.277.1.6.1.1.162 | ColumncktMPForcedCallee | read-write | mandatory | Whether this end of the circuit has been forced to be callee to support Multilink PPP PVC Attributes Modification Feature. |
| 1.3.6.1.4.1.277.1.6.1.1.163 | ColumncktFrameSize | read-write | mandatory | The average frame size (measured in number of bytes) of the traffic on the circuit. If not configured, it is set to 280 (bytes) by default. |
| 1.3.6.1.4.1.277.1.6.1.1.164 | ColumncktRFrameSize | read-write | mandatory | The average frame size (measured in number of bytes) of the traffic on the circuit on the reverse direction. If not configured, it is set to 280 (bytes) by def… |
| 1.3.6.1.4.1.277.1.6.1.1.165 | ColumncktRNrtsCLP1 | read-write | mandatory | Whether to use the discard threshold as the CLP1 Discard threshold upon reception of a cell by the NRTS processor in the reverse direction. |
| 1.3.6.1.4.1.277.1.6.1.1.166 | ColumncktBBearerAtmTransferCapability | read-only | mandatory | The broadband bearer ATM transfer capability of this SVC. This object is not pertinent to IISP 3.x, UNI 3.x or Q.2931 signaling. |
| 1.3.6.1.4.1.277.1.6.1.1.167 | ColumncktAtmFrameDiscard | read-write | mandatory | The ATM frame discard state for this circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.168 | ColumncktRAtmFrameDiscard | read-write | mandatory | The reverse ATM frame discard state for this circuit. |
| 1.3.6.1.4.1.277.1.6.1.1.169 | ColumncktAbrFRMRTT | read-only | mandatory | The ABR fixed RM round trip time for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.170 | ColumncktAbrICR | read-only | mandatory | The ABR initial cell rate for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.171 | ColumncktRAbrICR | read-only | mandatory | The reverse ABR initial cell rate for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.172 | ColumncktAbrRIF | read-only | mandatory | The ABR rate increase factor for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.173 | ColumncktRAbrRIF | read-only | mandatory | The reverse ABR rate increase factor for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.174 | ColumncktAbrRDF | read-only | mandatory | The ABR rate decrease factor for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.175 | ColumncktRAbrRDF | read-only | mandatory | The reverse ABR rate decrease factor for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.176 | ColumncktAbrTBE | read-only | mandatory | The ABR transient buffer exposure for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.177 | ColumncktRAbrTBE | read-only | mandatory | The reverse ABR transient buffer exposure for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.178 | ColumncktAbrNRM | read-only | mandatory | The ABR NRM for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.179 | ColumncktRAbrNRM | read-only | mandatory | The reverse ABR NRM for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.180 | ColumncktAbrTRM | read-only | mandatory | The ABR TRM for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.181 | ColumncktRAbrTRM | read-only | mandatory | The reverse ABR TRM for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.182 | ColumncktAbrCDF | read-only | mandatory | The ABR CDF for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.183 | ColumncktRAbrCDF | read-only | mandatory | The reverse ABR CDF for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.184 | ColumncktAbrADTF | read-only | mandatory | The ABR ADTF for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.185 | ColumncktRAbrADTF | read-only | mandatory | The reverse ABR ADTF for this SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.186 | ColumncktAccumCTD | read-only | mandatory | The accumulated cell(frame) transfer delay for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid. |
| 1.3.6.1.4.1.277.1.6.1.1.187 | ColumncktAccumCDV | read-only | mandatory | The accumulated cell delay variation for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid. |
| 1.3.6.1.4.1.277.1.6.1.1.188 | ColumncktAccumRCDV | read-only | mandatory | The accumulated reverse cell delay variation for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid. |
| 1.3.6.1.4.1.277.1.6.1.1.189 | ColumncktCLR | read-write | mandatory | The cell loss ratio requirement, expressed as a negative exponent of 10. The default value 255 represents any cell loss ratio acceptable. |
| 1.3.6.1.4.1.277.1.6.1.1.190 | ColumncktRCLR | read-write | mandatory | The reverse cell loss ratio requirement, expressed as a negative exponent of 10. The default value 255 represents any cell loss ratio acceptable. |
| 1.3.6.1.4.1.277.1.6.1.1.191 | ColumncktAtmLijId | read-only | mandatory | The Leaf Initiated Join ID of the PMP SVC rooted at this interface. |
| 1.3.6.1.4.1.277.1.6.1.1.192 | ColumncktAtmLijType | read-only | mandatory | The Leaf Initiated Join type of the PMP SVC rooted at this interface. |
| 1.3.6.1.4.1.277.1.6.1.1.193 | ColumncktRtLastDelay | read-only | mandatory | The last round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.194 | ColumncktRtAccuMinDelay | read-only | mandatory | The prev min round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.195 | ColumncktRtAccuMaxDelay | read-only | mandatory | The prev max round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.196 | ColumncktRtAccuAvgDelay | read-only | mandatory | The prev avg round-trip delay (micro-seconds). |
| 1.3.6.1.4.1.277.1.6.1.1.197 | ColumncktQosIntPeriod | read-write | mandatory | The number of periods for calculating qos params. |
| 1.3.6.1.4.1.277.1.6.1.1.198 | ColumncktAtmOutOAMClp0Cells | read-only | mandatory | The number of OAM CLP0 cells transmitted on this circuit. For BIO1 card (on Garnet Platform), this count is not reported separately - see cktEntry 99. |
| 1.3.6.1.4.1.277.1.6.1.1.199 | ColumncktAtmOutOAMClp1Cells | read-only | mandatory | The number of OAM CLP1 cells transmitted on this circuit. For BIO1 card (on Garnet Platform), this count is not reported separately - see cktEntry 100. |
| 1.3.6.1.4.1.277.1.6.1.1.200 | ColumncktReqCTD | read-write | mandatory | The requested cell/frame delay variation for this circuit, in microseconds. The range for PVC is 1 - 0x00FFFFFF. The default is 0x00FFFFFF, which means not val… |
| 1.3.6.1.4.1.277.1.6.1.1.201 | ColumncktInOctetsPeak | read-only | mandatory | The 5-minute peak value of the number of inbound octets (bytes) for the circuit - from Bulk Statistics. |
| 1.3.6.1.4.1.277.1.6.1.1.202 | ColumncktOutOctetsPeak | read-only | mandatory | The 5-minute peak value of the number of outbound octets (bytes) for the circuit - from Bulk Statistics. |
| 1.3.6.1.4.1.277.1.6.1.1.203 | ColumncktInDEOctetsPeak | read-only | mandatory | The 5-minute peak value of the number of inbound DE-marked octets (bytes) for the circuit - from Bulk Statistics. |
| 1.3.6.1.4.1.277.1.6.1.1.204 | ColumncktOutDEOctetsPeak | read-only | mandatory | The 5-minute peak value of the number of outbound DE-marked octets (bytes) for the circuit - from Bulk Statistics. |
| 1.3.6.1.4.1.277.1.6.1.1.205 | ColumncktInODEOctetsPeak | read-only | mandatory | The 5-minute peak value of the number of inbound ODE-marked octets (bytes) for the circuit - from Bulk Statistics. |
| 1.3.6.1.4.1.277.1.6.1.1.206 | ColumncktOutODEOctetsPeak | read-only | mandatory | The 5-minute peak value of the number of outbound ODE-marked octets (bytes) for the circuit - from Bulk Statistics. |
| 1.3.6.1.4.1.277.1.6.1.1.207 | ColumncktAdminCostThreshold | read-write | mandatory | Maximum allowable admin cost for the circuit. If no paths are available with cost less than or equal to this value, the circuit is not established. DEFVAL is 0… |
| 1.3.6.1.4.1.277.1.6.1.1.208 | ColumncktAtmSvcServiceCategory | read-only | mandatory | The derived service category in the forward direction for this ATM SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.209 | ColumncktAtmSvcRServiceCategory | read-only | mandatory | The derived service category in the reverse direction for this ATM SVC. |
| 1.3.6.1.4.1.277.1.6.1.1.210 | ColumncktInterworkingFrToAtmEFCI | read-write | mandatory | EFCI mapping for Frame Relay To ATM Service Interworking. |
| 1.3.6.1.4.1.277.1.6.1.1.211 | ColumncktDiagSARMon | read-write | mandatory | Used to start or stop flow on the inbound/outbound ATMizer without informing the PPC. |
| 1.3.6.1.4.1.277.1.6.1.1.212 | ColumncktAdminCostReal | read-only | mandatory | Actual value of total administration cost of a circuit. Ranges from 0 to 0xFFFFFFFF. |
| 1.3.6.1.4.1.277.1.6.1.1.213 | ColumncktAtmInClp0Cells | read-only | mandatory | The Number of ATM CLP 0 cells received on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.214 | ColumncktAtmInClp1Cells | read-only | mandatory | The Number of ATM CLP 1 cells received on a VC (VPC or VCC). |
| 1.3.6.1.4.1.277.1.6.1.1.215 | ColumncktATMAAL5CRC32Error | read-only | mandatory | Number of received AAL5 packets with CRC32 errors. |
| 1.3.6.1.4.1.277.1.6.1.1.216 | ColumncktATMAAL5CPIError | read-only | mandatory | Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros |
| 1.3.6.1.4.1.277.1.6.1.1.217 | ColumncktATMAAL5LengthError | read-only | mandatory | Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - length value in trailer > 55 by… |
| 1.3.6.1.4.1.277.1.6.1.1.218 | ColumncktATMAAL5ReassemblyTimerError | read-only | mandatory | Number of expired reassembly timers |
| 1.3.6.1.4.1.277.1.6.1.1.219 | ColumncktATMAAL5MaxNrSegError | read-only | mandatory | Number of received AAL5 packets which exceeds the maximum allowed length |
| 1.3.6.1.4.1.277.1.6.1.1.220 | ColumncktIWF1490to1483Error | read-only | mandatory | Number of Frames received that failed the rfc1490 to rfc 1483 header translation. This error counter indicates that frames being recevied from the frame relay … |
| 1.3.6.1.4.1.277.1.6.1.1.221 | ColumncktIWF1490to1483LastBadHeader | read-only | mandatory | Ascii string of the first 8 bytes of the header from the last frame discarded because the 1490 to 1483 header translation failed. The string displays the hexid… |
| 1.3.6.1.4.1.277.1.6.1.1.222 | ColumncktIWF1483to1490Error | read-only | mandatory | Number of Frames received that failed the rfc1483 to rfc 1490 header translation. This error counter indicates that frames being recevied from the atm side of … |
| 1.3.6.1.4.1.277.1.6.1.1.223 | ColumncktIWF1483to1490LastBadHeader | read-only | mandatory | Ascii string of the first 10 bytes of the header from the last frame discarded because the 1483 to 1490 header translation failed. The string displays the hexi… |
| 1.3.6.1.4.1.277.1.6.2 | TablecktLeafTable | not-accessible | mandatory | A table containing information about leaves of multipoint circuits. |
| 1.3.6.1.4.1.277.1.6.2.1 | RowcktLeafEntry | not-accessible | mandatory | The objects relevant to a single leaf in a multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.1 | ColumncktLeafSrcIfIndex | read-only | mandatory | The interface ID at this node's ingress port for the corresponding multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.2 | ColumncktLeafSrcDlci | read-only | mandatory | The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's ingress port for the corresponding multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.3 | ColumncktLeafEndpointIndex | read-only | mandatory | An identifier unique to this leaf for the corresponding multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.4 | ColumncktLeafCreationTime | read-only | mandatory | The value of sysUpTime when this leaf was created for the corresponding multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.5 | ColumncktLeafEgressIfIndex | read-only | mandatory | The interface ID at this node's egress port for this leaf's segment of the corresponding multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.6 | ColumncktLeafEgressDlci | read-only | mandatory | The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's egress port for this leaf's segment of the corresponding mul… |
| 1.3.6.1.4.1.277.1.6.2.1.7 | ColumncktLeafDestNodeId | read-write | mandatory | The node ID of the node where this leaf terminates. |
| 1.3.6.1.4.1.277.1.6.2.1.8 | ColumncktLeafDestIfIndex | read-write | mandatory | The interface ID at the egress port of the destination node for this leaf, if this is a PVC. |
| 1.3.6.1.4.1.277.1.6.2.1.9 | ColumncktLeafDestDlci | read-only | mandatory | The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's destination port for the corresponding multipoint circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.10 | ColumncktLeafSvcCallingParty | read-only | mandatory | The calling party number for this leaf, if this is an SVC. |
| 1.3.6.1.4.1.277.1.6.2.1.11 | ColumncktLeafSvcCalledParty | read-only | mandatory | The called party number for this leaf, if this is an SVC. |
| 1.3.6.1.4.1.277.1.6.2.1.12 | ColumncktLeafAdminStatus | read-write | mandatory | The desired state for the leaf entry. |
| 1.3.6.1.4.1.277.1.6.2.1.13 | ColumncktLeafVcState | read-only | mandatory | The current state of the leaf PVC segment in the Cascade network. |
| 1.3.6.1.4.1.277.1.6.2.1.14 | ColumncktLeafOperStatus | read-only | mandatory | The current operational status of the entire leaf PVC. |
| 1.3.6.1.4.1.277.1.6.2.1.15 | ColumncktLeafDceState | read-only | mandatory | The DCE state of the circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.16 | ColumncktLeafDteStatus | read-only | mandatory | The DTE status of the circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.17 | ColumncktLeafDteState | read-only | mandatory | The DTE state of the circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.18 | ColumncktLeafVcPtr | read-only | mandatory | An 8-byte Octect string indicating the vc pointer. |
| 1.3.6.1.4.1.277.1.6.2.1.19 | ColumncktLeafHopCnt | read-only | mandatory | The count of hops along the circuit path. (Max is 16) |
| 1.3.6.1.4.1.277.1.6.2.1.20 | ColumncktLeafPath | read-only | mandatory | The circuit path consisting a sequence of outbound interface indexes at nodes along the established circuit. The format is interface:interface:interface...... |
| 1.3.6.1.4.1.277.1.6.2.1.21 | ColumncktLeafFailReason | read-only | mandatory | The reason for the PVC establishment failure. |
| 1.3.6.1.4.1.277.1.6.2.1.22 | ColumncktLeafFailNode | read-only | mandatory | The node which causes the PVC failure. |
| 1.3.6.1.4.1.277.1.6.2.1.23 | ColumncktLeafFailPort | read-only | mandatory | The port on the fail node which causes the PVC failure. |
| 1.3.6.1.4.1.277.1.6.2.1.24 | ColumncktLeafHelloCounter | read-only | mandatory | Number of PVC hello pdu frames received in the VC entry of the called side. |
| 1.3.6.1.4.1.277.1.6.2.1.25 | ColumncktLeafHelloAckCounter | read-only | mandatory | Number of PVC hello Ack pdu frames received in the VC entry of the calling side. |
| 1.3.6.1.4.1.277.1.6.2.1.26 | ColumncktLeafAtmVPI | read-write | mandatory | VPI value in the ATM cell header |
| 1.3.6.1.4.1.277.1.6.2.1.27 | ColumncktLeafAtmVCI | read-write | mandatory | VCI value in the ATM cell header |
| 1.3.6.1.4.1.277.1.6.2.1.28 | ColumncktLeafType | read-only | mandatory | 1 if a permanent virtual circuit; 2 if a switched virtual circuit. |
| 1.3.6.1.4.1.277.1.6.2.1.29 | ColumncktLeafAtmInCells | read-only | mandatory | The Number of ATM cells received on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.30 | ColumncktLeafAtmOutCells | read-only | mandatory | The Number of ATM cells transmitted on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.31 | ColumncktLeafAtmInDiscardedClp0Cells | read-only | mandatory | The Number of ATM CLP0 cells received and discarded on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.32 | ColumncktLeafAtmInDiscardedClp1Cells | read-only | mandatory | The Number of ATM CLP1 cells received and discarded on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.33 | ColumncktLeafAtmInPassedClp0Cells | read-only | mandatory | The Number of ATM CLP 0 cells received and passed UPC on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.34 | ColumncktLeafAtmInPassedClp1Cells | read-only | mandatory | The Number of ATM CLP 1 cells received and passed UPC on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.35 | ColumncktLeafAtmInTaggedCells | read-only | mandatory | The Number of ATM cells received and tagged on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.36 | ColumncktLeafAtmOutClp0Cells | read-only | mandatory | The Number of ATM CLP 0 cells transmitted on a VCC. |
| 1.3.6.1.4.1.277.1.6.2.1.37 | ColumncktLeafAtmOutClp1Cells | read-only | mandatory | The Number of ATM CLP 1 cells transmitted on a VCC. |
| 1.3.6.1.4.1.277.1.6.3 | TablecktSmdsRtTable | not-accessible | mandatory | A table containing information about destination, VC, hops and routes. |
| 1.3.6.1.4.1.277.1.6.3.1 | RowcktSmdsRtEntry | not-accessible | mandatory | The information regarding routes from a node to all its neighbors. |
| 1.3.6.1.4.1.277.1.6.3.1.1 | ColumncktSmdsRemoteNode | read-only | mandatory | The nodeId of the node to which a rought is sought. |
| 1.3.6.1.4.1.277.1.6.3.1.2 | ColumncktSmdsHopCnt | read-only | mandatory | The number of hops to reach the desired destination node. |
| 1.3.6.1.4.1.277.1.6.3.1.3 | ColumncktSmdsRoute | read-only | mandatory | The out-going Interface Id of each of the nodes in the path. |
| 1.3.6.1.4.1.277.1.6.3.1.4 | ColumncktSmdsLocalPort | read-only | mandatory | The out-going local portId. |
| 1.3.6.1.4.1.277.1.6.3.1.5 | ColumncktSmdsRemotePort | read-only | mandatory | The remote portId of the destination nodeId. |
| 1.3.6.1.4.1.277.1.6.3.1.6 | ColumncktSmdsVcState | read-only | mandatory | The state of the circuit. |
| 1.3.6.1.4.1.277.1.7 | Nodecard | |||
| 1.3.6.1.4.1.277.1.7 | NodenodeSwDownloadComplete | This trap indicates that a software download was complete. | ||
| 1.3.6.1.4.1.277.1.7.1 | ScalarcardNumber | read-only | mandatory | The number of manageable cards physically present in this node. Standby cards are not considered manageable. |
| 1.3.6.1.4.1.277.1.7.2 | TablecardTable | not-accessible | mandatory | A list of cardEntry's. The number of entries is given by the value of cardNumber |
| 1.3.6.1.4.1.277.1.7.2.1 | RowcardEntry | not-accessible | mandatory | The card entry contains objects relevant to managing intelligent cards. |
| 1.3.6.1.4.1.277.1.7.2.1.1 | ColumncardLogicalSlotId | read-only | mandatory | The logical slot number of this card. This is used as an index for the cardTable. In redundant configurations, this can be the physical slot number of either r… |
| 1.3.6.1.4.1.277.1.7.2.1.2 | ColumncardPhysicalSlotId | read-only | mandatory | The physical slot number of this card. This can be different from cardLogicalSlotId in redundant configurations. |
| 1.3.6.1.4.1.277.1.7.2.1.3 | ColumncardAdminType | read-write | mandatory | The desired card type. |
| 1.3.6.1.4.1.277.1.7.2.1.4 | ColumncardOperType | read-only | mandatory | The actual card type. |
| 1.3.6.1.4.1.277.1.7.2.1.5 | ColumncardState | read-only | mandatory | The state of this card. |
| 1.3.6.1.4.1.277.1.7.2.1.6 | ColumncardAdminStatus | read-write | mandatory | The desired status of this card. |
| 1.3.6.1.4.1.277.1.7.2.1.7 | ColumncardOperStatus | read-only | mandatory | The current status of this card. |
| 1.3.6.1.4.1.277.1.7.2.1.8 | ColumncardDiagStatus | read-only | mandatory | The current diagnostics status of this card, as determined by background diagnostics. |
| 1.3.6.1.4.1.277.1.7.2.1.9 | ColumncardRedundConfig | read-only | mandatory | Is the card configured for redundancy? |
| 1.3.6.1.4.1.277.1.7.2.1.10 | ColumncardRedundSlotMask | read-write | mandatory | A 32-bit mask indicating the slot position of this card and its redundant partner. The low bit is slot 1 and the high bit is slot 32. |
| 1.3.6.1.4.1.277.1.7.2.1.11 | ColumncardRedundActual | read-only | mandatory | Is the card currently connected to a redundant card? |
| 1.3.6.1.4.1.277.1.7.2.1.12 | ColumncardRedundState | read-only | mandatory | The current redundancy state of this card. Exception: when used as an index for the following objects: cardAdminType, cardAdminCapability, and cardAdminStatus,… |
| 1.3.6.1.4.1.277.1.7.2.1.13 | ColumncardToRedundant | read-write | mandatory | Instructs the standby card to reset the active card and take over as new active card. The reset takes place after specified time ticks have elapsed. A value of… |
| 1.3.6.1.4.1.277.1.7.2.1.14 | ColumncardDiagNonFatalSource | read-only | mandatory | Source who reported last non-fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.15 | ColumncardDiagNonFatalTime | read-only | mandatory | Time the last non-fatal error was reported. |
| 1.3.6.1.4.1.277.1.7.2.1.16 | ColumncardDiagNonFatalErrMajor | read-only | mandatory | Major error code of last non-fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.17 | ColumncardDiagNonFatalErrMinor | read-only | mandatory | Minor error code of last non-fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.18 | ColumncardDiagNonFatalStr | read-only | mandatory | Ascii string describing last non-fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.19 | ColumncardDiagFatalSource | read-only | mandatory | Source who reported last fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.20 | ColumncardDiagFatalTime | read-only | mandatory | Time the last fatal error was reported. |
| 1.3.6.1.4.1.277.1.7.2.1.21 | ColumncardDiagFatalErrMajor | read-only | mandatory | Major error code of last fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.22 | ColumncardDiagFatalErrMinor | read-only | mandatory | Minor error code of last fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.23 | ColumncardDiagFatalStr | read-only | mandatory | Ascii string describing last fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.24 | ColumncardDiagFatalReboots | read-only | mandatory | Number of times the switch has re-booted since last fatal error was reported. |
| 1.3.6.1.4.1.277.1.7.2.1.25 | ColumncardDiagFatalAddress | read-only | mandatory | Address switch was executing when it encountered fatal error. |
| 1.3.6.1.4.1.277.1.7.2.1.26 | ColumncardDiagBackgroundPasses | read-only | mandatory | Number of passes made by the background diagnostics. |
| 1.3.6.1.4.1.277.1.7.2.1.27 | ColumncardDiagBackgroundFailures | read-only | mandatory | Number of failures discovered by background diagnostics. |
| 1.3.6.1.4.1.277.1.7.2.1.28 | ColumncardDiagBackgroundSuccesses | read-only | mandatory | Number of successful passes by background diagnostics. |
| 1.3.6.1.4.1.277.1.7.2.1.29 | ColumncardDiagLEDReset | read-write | mandatory | Change the card state from marginal to active. Change the LED from yellow to green. |
| 1.3.6.1.4.1.277.1.7.2.1.30 | ColumncardDiagPowerExtensive | read-write | mandatory | Should power on diagnostics do slower, extensive testing, or fast testing? |
| 1.3.6.1.4.1.277.1.7.2.1.31 | ColumncardCpuUtil | read-only | mandatory | The CPU utilization percentage for packet processing on this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.32 | ColumncardMemoryUsage | read-only | mandatory | The memory utilization, in terms of free bytes, for this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.33 | ColumncardMaxVCs | read-only | mandatory | The number of available VC entries on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.34 | ColumncardInUseVCs | read-only | mandatory | The number of currently in use VC entries on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.35 | ColumncardFreeVCs | read-only | mandatory | The number of currently free VC entries on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.36 | ColumncardInOctets | read-only | mandatory | The total number of octets received on this card, including framing bytes. |
| 1.3.6.1.4.1.277.1.7.2.1.37 | ColumncardInPkts | read-only | mandatory | The total number of packets received on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.38 | ColumncardOutOctets | read-only | mandatory | The total number of octets transmitted out of this card, including framing bytes. |
| 1.3.6.1.4.1.277.1.7.2.1.39 | ColumncardOutPkts | read-only | mandatory | The total number of packets requested to be transmitted out of this card, including those that were discarded or not sent. |
| 1.3.6.1.4.1.277.1.7.2.1.40 | ColumncardToWarmboot | read-write | mandatory | Warm boots the card after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request. |
| 1.3.6.1.4.1.277.1.7.2.1.41 | ColumncardToColdboot | read-write | mandatory | Cold boots the card after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request. |
| 1.3.6.1.4.1.277.1.7.2.1.42 | ColumncardModel | read-only | mandatory | The part number of the card. |
| 1.3.6.1.4.1.277.1.7.2.1.43 | ColumncardSerial | read-only | mandatory | The serial number of the card. |
| 1.3.6.1.4.1.277.1.7.2.1.44 | ColumncardSwRev | read-only | mandatory | The software rev number (major.minor). |
| 1.3.6.1.4.1.277.1.7.2.1.45 | ColumncardHwRev | read-only | mandatory | The hardware rev number (major.minor). |
| 1.3.6.1.4.1.277.1.7.2.1.46 | ColumncardEpromRev | read-only | mandatory | The EPROM firmware rev number (major.minor). |
| 1.3.6.1.4.1.277.1.7.2.1.47 | ColumncardName | read-write | mandatory | The name of this card |
| 1.3.6.1.4.1.277.1.7.2.1.48 | ColumncardCktGroupTrap | read-only | mandatory | This is a ( 4 + n*134 ) byte octet string where n => 1. The first and second byte is the interface/slot id of the link/IOP going down or link goes up. The thir… |
| 1.3.6.1.4.1.277.1.7.2.1.49 | ColumncardOutBtus | read-only | mandatory | The number of bus transfer units sent by this card. |
| 1.3.6.1.4.1.277.1.7.2.1.50 | ColumncardInGoodBtus | read-only | mandatory | The number of good bus transfer units received by this card. |
| 1.3.6.1.4.1.277.1.7.2.1.51 | ColumncardInErrorBtus | read-only | mandatory | The number of bus transfer units received with errors. |
| 1.3.6.1.4.1.277.1.7.2.1.52 | ColumncardInNoVcBtus | read-only | mandatory | The number of bus transfer units discarded because no circuit was found. |
| 1.3.6.1.4.1.277.1.7.2.1.53 | ColumncardInLinkDownBtus | read-only | mandatory | The number of bus transfer units discarded because the outgoing link was inactive. |
| 1.3.6.1.4.1.277.1.7.2.1.54 | ColumncardInNoBufferBtus | read-only | mandatory | The number of bus transfer units discarded because no buffer was available. |
| 1.3.6.1.4.1.277.1.7.2.1.55 | ColumncardInForwardBitBtus | read-only | mandatory | The number of bus transfer units discarded because the circuit forward bit was off. |
| 1.3.6.1.4.1.277.1.7.2.1.56 | ColumncardDiagTestId | read-write | mandatory | Identification of the diagnostics tests to be run. |
| 1.3.6.1.4.1.277.1.7.2.1.57 | ColumncardDiagTestRuns | read-write | mandatory | The number of passes of the diagnostics tests to be run. The default value is 1. |
| 1.3.6.1.4.1.277.1.7.2.1.58 | ColumncardDiagState | read-write | mandatory | The current state of the foreground diagnostics on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.59 | ColumncardDiagOptionStr | read-write | mandatory | Optional parameters to the diagnostic. |
| 1.3.6.1.4.1.277.1.7.2.1.60 | ColumncardDiagPasses | read-only | mandatory | Number of successful diagnostic passes. |
| 1.3.6.1.4.1.277.1.7.2.1.61 | ColumncardDiagFailures | read-only | mandatory | Number of failed diagnostic passes. |
| 1.3.6.1.4.1.277.1.7.2.1.62 | ColumncardDiagResultString | read-only | mandatory | Description of last diagnostic failure. |
| 1.3.6.1.4.1.277.1.7.2.1.63 | ColumncardFrameMemoryUtil | read-only | mandatory | The percentage of frame memory utilization on this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.64 | ColumncardResetPram | read-write | mandatory | Setting this to 1 causes a reset of PRAM on the corresponding card. |
| 1.3.6.1.4.1.277.1.7.2.1.65 | ColumncardMemoryUtil | read-only | mandatory | The percentage of system memory utilization on this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.66 | ColumncardFrameMemoryUsage | read-only | mandatory | The frame memory utilization, in terms of free bytes, for this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.67 | ColumncardUpTime | read-only | mandatory | The time (in hundredths of a second) since this card was last booted. |
| 1.3.6.1.4.1.277.1.7.2.1.68 | ColumncardPramChecksum | read-only | mandatory | The PRAM checksum for this card. |
| 1.3.6.1.4.1.277.1.7.2.1.69 | ColumncardPhysicalIndex | read-only | mandatory | The physical slot id of this card. |
| 1.3.6.1.4.1.277.1.7.2.1.70 | ColumncardExternalClockRate | read-only | mandatory | The external clock rate for DSX1, T1 and E1 cards. The value is specified in units of 8KHz and can range from 1 to 255. |
| 1.3.6.1.4.1.277.1.7.2.1.71 | ColumncardShootState | read-write | mandatory | Specifies whether the system monitor on the CP should shoot this card if it's unreachable. The default is enabled. The card index used in the binding refers to… |
| 1.3.6.1.4.1.277.1.7.2.1.72 | ColumncardEraseAll | read-write | mandatory | When set to 1, erases program flash and PRAM on specified card. |
| 1.3.6.1.4.1.277.1.7.2.1.73 | ColumncardAdminCapability | read-write | mandatory | The desired capability of the card |
| 1.3.6.1.4.1.277.1.7.2.1.74 | ColumncardOperCapability | read-only | mandatory | The actual capability of the card |
| 1.3.6.1.4.1.277.1.7.2.1.75 | ColumncardISDNswtype | read-write | mandatory | Specifies the ISDN central office switch type for the card. |
| 1.3.6.1.4.1.277.1.7.2.1.76 | ColumncardCpuFgUtil | read-only | mandatory | The CPU foreground utilization percentage for packet processing on this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.77 | ColumncardTrkProtState | read-write | mandatory | Control for issue of Link Trunk Protocol request frames. If set to disabled, the issue of trunk protocol requests is blocked for all trunks on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.78 | ColumncardISDNSigType | read-write | mandatory | Specifies whether the ISDN Signalling type is Associated or Non-Facility Associated Signalling |
| 1.3.6.1.4.1.277.1.7.2.1.79 | ColumncardISDNChanId | read-write | mandatory | Specifies whether Channel ID assignment is performed by the central office switch or the 9000 - Exclusive (central office) Preferred (9000) |
| 1.3.6.1.4.1.277.1.7.2.1.80 | ColumncardTransmitClockConfig | read-write | mandatory | The transmit clock source for timing section of the card |
| 1.3.6.1.4.1.277.1.7.2.1.81 | ColumncardTransmitClockSwitchOver | read-write | mandatory | Enable/disable automatic transmit clock source switch-over once a failed clock reference has recovered. |
| 1.3.6.1.4.1.277.1.7.2.1.82 | ColumncardTransmitClockStatus | read-only | mandatory | The transmit clock PLL synchronization status of the card |
| 1.3.6.1.4.1.277.1.7.2.1.83 | ColumncardSystemPrimaryClockPortConfig | read-write | mandatory | The port number (1-x) on the card that specifies the system primary clock source. A zero specifies no port |
| 1.3.6.1.4.1.277.1.7.2.1.84 | ColumncardSystemPrimaryClockStatus | read-only | mandatory | The system primary clock status as detected on the card. On the BIO, this refers to the Timing Module 1 clock status as detected by the BIO. |
| 1.3.6.1.4.1.277.1.7.2.1.85 | ColumncardSystemSecondaryClockPortConfig | read-write | mandatory | The port number (1 to x) on the card that specifies the system secondary clock source. A zero specifies no port |
| 1.3.6.1.4.1.277.1.7.2.1.86 | ColumncardSystemSecondaryClockStatus | read-only | mandatory | The system secondary clock status as detected on the card. On the BIO, this refers to the Timing Module 2 clock status as detected by the BIO. |
| 1.3.6.1.4.1.277.1.7.2.1.87 | ColumncardInCells | read-only | mandatory | The total number of cells received on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.88 | ColumncardInErrorCells | read-only | mandatory | The total number of cells received on this card with HEC error. |
| 1.3.6.1.4.1.277.1.7.2.1.89 | ColumncardInErrorVPIVCI | read-only | mandatory | The total number of cells received with HEC invalid VPI, VCI. |
| 1.3.6.1.4.1.277.1.7.2.1.90 | ColumncardOutCells | read-only | mandatory | The total number of cells transmitted out of this card |
| 1.3.6.1.4.1.277.1.7.2.1.91 | ColumncardOutDiscardCells | read-only | mandatory | The total number of cells discarded due to congestion on this card |
| 1.3.6.1.4.1.277.1.7.2.1.92 | ColumncardQOSQueueSize | read-only | mandatory | The ATM QOS queue size (per cell) of each port on the card |
| 1.3.6.1.4.1.277.1.7.2.1.93 | ColumncardLastErrorPort | read-only | mandatory | The port number (1 to x) of the last cell with invalid cell header on the card |
| 1.3.6.1.4.1.277.1.7.2.1.94 | ColumncardLastErrorVPI | read-only | mandatory | The VPI of the last cell with invalid cell header on the card |
| 1.3.6.1.4.1.277.1.7.2.1.95 | ColumncardLastErrorVCI | read-only | mandatory | The VCI of the last cell with invalid cell header on the card |
| 1.3.6.1.4.1.277.1.7.2.1.96 | ColumncardSystemPrimaryClockModeConfig | read-write | mandatory | The system primary clock mode. PLCP is for DS3 port only |
| 1.3.6.1.4.1.277.1.7.2.1.97 | ColumncardSystemSecondaryClockModeConfig | read-write | mandatory | The system secondary clock mode. PLCP is for DS3 port only |
| 1.3.6.1.4.1.277.1.7.2.1.98 | ColumncardNFBDEStatus | read-write | mandatory | Non Fatal Background Diagnostic Error Status |
| 1.3.6.1.4.1.277.1.7.2.1.99 | ColumncardProductCode | read-only | mandatory | This card's product code. |
| 1.3.6.1.4.1.277.1.7.2.1.100 | ColumncardMfgPN | read-only | mandatory | This card's manufacturing part number. |
| 1.3.6.1.4.1.277.1.7.2.1.101 | ColumncardTotalUpTime | read-only | mandatory | This card's total accumulated up time, in hours. |
| 1.3.6.1.4.1.277.1.7.2.1.102 | ColumncardIOAType | read-only | mandatory | The type of IOA attached to this card. |
| 1.3.6.1.4.1.277.1.7.2.1.103 | ColumncardIOAHwRev | read-only | mandatory | The attached IOA's hardware revision. |
| 1.3.6.1.4.1.277.1.7.2.1.104 | ColumncardIOASerial | read-only | mandatory | The attached IOA's serial number. |
| 1.3.6.1.4.1.277.1.7.2.1.105 | ColumncardIOAProductCode | read-only | mandatory | The attached IOA's product code. |
| 1.3.6.1.4.1.277.1.7.2.1.106 | ColumncardIOAMfgPN | read-only | mandatory | The attached IOA's manufacturing part number. |
| 1.3.6.1.4.1.277.1.7.2.1.107 | ColumncardDS0Support | read-only | mandatory | Some B-Stdx T1 boards do not support lpbk. |
| 1.3.6.1.4.1.277.1.7.2.1.108 | ColumncardDiagParamId | read-write | mandatory | Parameter identifier for internal diagnostics. |
| 1.3.6.1.4.1.277.1.7.2.1.109 | ColumncardDiagParamValue | read-write | mandatory | Value assigned to parameter specified by cardDiagParamId. |
| 1.3.6.1.4.1.277.1.7.2.1.110 | ColumncardBulkStatsPeakCapability | read-write | mandatory | Configures capability to collect peak 5-minute statistics. Capability change takes effect upon IOM reboot. |
| 1.3.6.1.4.1.277.1.7.2.1.111 | ColumncardBulkStatsTotalCapability | read-write | mandatory | Configures capability to collect total statistics. Capability change takes effect upon IOM reboot. |
| 1.3.6.1.4.1.277.1.7.2.1.112 | ColumncardBulkStatsPeakEnable | read-write | mandatory | Reflects the operational state of the peak 5-minute statistic collection on an IOM. For this setting to be enabled, the respective capability must be enabled. |
| 1.3.6.1.4.1.277.1.7.2.1.113 | ColumncardBulkStatsTotalEnable | read-write | mandatory | Reflects the operational state of the total statistic collection on an IOM. For this setting to be enabled, the respective capability must be enabled. |
| 1.3.6.1.4.1.277.1.7.2.1.114 | ColumncardBulkStatsBaseCollectPeriod | read-write | mandatory | Configures base collection period for bulk statistics on an IOM in minutes. Only the following values are allowed: 15, 20, 30, 60, 120, 180, 240, 360, 720, 144… |
| 1.3.6.1.4.1.277.1.7.2.1.115 | ColumncardNrtsHwRev | read-only | mandatory | Hardware revision of the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.116 | ColumncardNrtsOutCellBufSize | read-only | mandatory | The size of the NRTS output cell buffer. |
| 1.3.6.1.4.1.277.1.7.2.1.117 | ColumncardNrtsOperState | read-only | mandatory | The operational status of the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.118 | ColumncardNrtsAdminState | read-write | mandatory | The admin status of the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.119 | ColumncardNrtsCcrmProtocolId | read-write | mandatory | The protocol ID field for the CCRM cells. Must be different from the BCM protocol ID. Default is 6. |
| 1.3.6.1.4.1.277.1.7.2.1.120 | ColumncardNrtsBcmProtocolId | read-write | mandatory | The protocol ID field for the BCM cells. Must be different from the CCRM protocol ID. Default is 5. |
| 1.3.6.1.4.1.277.1.7.2.1.121 | ColumncardNrtsRmGenInterval | read-write | mandatory | The RM cell generation interval in ms. Minimum is 30, maximum is 250, default is 100. |
| 1.3.6.1.4.1.277.1.7.2.1.122 | ColumncardNrtsIdleCktThresh | read-write | mandatory | The number of RM cell generation intervals with no cell reception upon which the circuit is declared idle. Minimum is 1, maximum is 8, default is 8. |
| 1.3.6.1.4.1.277.1.7.2.1.123 | ColumncardNrtsVbrNrtManage | read-write | mandatory | Indicates whether VBR NRT traffic should be managed by the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.124 | ColumncardNrtsIcrFact | read-write | mandatory | A factor used to calculate the Initial Cell Rate for a circuit from its MCR and PCR. |
| 1.3.6.1.4.1.277.1.7.2.1.125 | ColumncardNrtsMcastDiscardThresh | read-write | mandatory | A NRTS discard threshold for the multicast circuits. |
| 1.3.6.1.4.1.277.1.7.2.1.126 | ColumncardNrtsMcastDiscardCount | read-only | mandatory | A NRTS discard counter for the multicast circuits. |
| 1.3.6.1.4.1.277.1.7.2.1.127 | ColumncardAdminIOAType | read-write | mandatory | The type of IOA attached to this card viewed from NMS. |
| 1.3.6.1.4.1.277.1.7.2.1.128 | ColumncardNrtsMcastRate | read-write | mandatory | The NRTS shaping rate for multicast circuits as a fraction of the line rate. |
| 1.3.6.1.4.1.277.1.7.2.1.129 | ColumncardMonStatus | read-write | mandatory | |
| 1.3.6.1.4.1.277.1.7.2.1.130 | ColumncardImageSetA | read-only | mandatory | The details of Image Set A. The elements of each image are space delimited and include Part Number, Revision, Size and Description. The details of each image a… |
| 1.3.6.1.4.1.277.1.7.2.1.131 | ColumncardImageSetB | read-only | mandatory | The details of Image Set B. The elements of each image are space delimited and include Part Number, Revision, Size and Description. The details of each image a… |
| 1.3.6.1.4.1.277.1.7.2.1.132 | ColumncardMacAddress | read-only | mandatory | ethernet MAC address of the card if there is an ethernet interface. Currently only CP cards may have ethernet. Cards without ethernet return 0 length octet str… |
| 1.3.6.1.4.1.277.1.7.2.1.133 | ColumncardFlashRev | read-only | mandatory | The boot flash rev number. |
| 1.3.6.1.4.1.277.1.7.2.1.134 | ColumncardRequiredCapabilityBitmask | read-only | mandatory | Bitmask indicating this cards' required capabilities based on configured features. A bit is set to one if the corresponding capability is required. This variab… |
| 1.3.6.1.4.1.277.1.7.2.1.135 | ColumncardOperCapabilityBitmask | read-only | mandatory | Bitmask indicating this cards' actual capabilities. A bit is set to one if the corresponding capability is supported. This variable is a bitmask so only power-… |
| 1.3.6.1.4.1.277.1.7.2.1.136 | ColumncardDslModule | read-write | mandatory | This is for Dynamic Software Loadl You can type: ModuleName Version, ModuleName Version, ... to load modules. |
| 1.3.6.1.4.1.277.1.7.2.1.137 | ColumncardIPTableSize | read-write | mandatory | The maximum number of IP routing table entries supported by the card. If set to 0, routing table size is assumed unlimited. |
| 1.3.6.1.4.1.277.1.7.2.1.138 | ColumncardIPTableState | read-only | mandatory | State of the card's IP routing table. If set to marginal, the routing table maximum size has been exceeded. and all routes except management prefixes have been… |
| 1.3.6.1.4.1.277.1.7.2.1.139 | ColumncardATMTcaInBufOverflowAlertPeriod | read-write | mandatory | The atm tca ingress buffer overflow alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.140 | ColumncardATMTcaInBufOverflowThresh | read-write | mandatory | The atm tca ingress buffer overflow threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.141 | ColumncardATMTcaInInvalidVpiVciAlertPeriod | read-write | mandatory | The atm tca ingress invalid vpi/vci alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.142 | ColumncardATMTcaInInvalidVpiVciThresh | read-write | mandatory | The atm tca ingress invalid vpi/vci threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.143 | ColumncardATMTcaInATMDCFullAlertPeriod | read-write | mandatory | The atm tca ingress ATM DC full alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.144 | ColumncardATMTcaInATMDCFullThresh | read-write | mandatory | The atm tca ingress ATM DC full threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.145 | ColumncardATMTcaEnable | read-write | mandatory | The atm tca enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.146 | ColumncardATMTcaId | read-only | mandatory | This object identifies the the most recently declared card ATM threshold crossing alert |
| 1.3.6.1.4.1.277.1.7.2.1.147 | ColumncardATMTcaECidLookupFailureAlertPeriod | read-write | mandatory | The atm tca ingress buffer overflow alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.148 | ColumncardATMTcaECidLookupThresh | read-write | mandatory | The atm tca ingress buffer overflow threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.149 | ColumncardATMTcaSPPearlOCbrFailureAlertPeriod | read-write | mandatory | The atm tca sp pearl overflow CBR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.150 | ColumncardATMTcaSPPearlOCbrThresh | read-write | mandatory | The atm tca sp pearl overflow CBR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.151 | ColumncardATMTcaSPPearlOAbrFailureAlertPeriod | read-write | mandatory | The atm tca sp pearl overflow ABR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.152 | ColumncardATMTcaSPPearlOAbrThresh | read-write | mandatory | The atm tca sp pearl overflow ABR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.153 | ColumncardATMTcaSPPearlOVbr1FailureAlertPeriod | read-write | mandatory | The atm tca sp pearl overflow VBR1 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.154 | ColumncardATMTcaSPPearlOVbr1Thresh | read-write | mandatory | The atm tca sp pearl overflow VBR1 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.155 | ColumncardATMTcaSPPearlOVbr2FailureAlertPeriod | read-write | mandatory | The atm tca sp pearl overflow VBR2 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.156 | ColumncardATMTcaSPPearlOVbr2Thresh | read-write | mandatory | The atm tca sp pearl overflow VBR2 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.157 | ColumncardATMTcaSPPearlGCbrFailureAlertPeriod | read-write | mandatory | The atm tca sp pearl congestion CBR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.158 | ColumncardATMTcaSPPearlGCbrThresh | read-write | mandatory | The atm tca sp pearl congestion CBR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.159 | ColumncardATMTcaSPPearlGAbrFailureAlertPeriod | read-write | mandatory | The atm tca sp pearl congestion ABR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.160 | ColumncardATMTcaSPPearlGAbrThresh | read-write | mandatory | The atm tca sp pearl congestion ABR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.161 | ColumncardATMTcaSPPearlGVbr1FailureAlertPeriod | read-write | mandatory | The atm tca sp pearl congestion VBR1 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.162 | ColumncardATMTcaSPPearlGVbr1Thresh | read-write | mandatory | The atm tca sp pearl congestion VBR1 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.163 | ColumncardATMTcaSPPearlGVbr2FailureAlertPeriod | read-write | mandatory | The atm tca sp pearl congestion VBR2 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.164 | ColumncardATMTcaSPPearlGVbr2Thresh | read-write | mandatory | The atm tca sp pearl congestion VBR2 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.165 | ColumncardATMTcaSPEnable | read-write | mandatory | The atm tca SP enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.166 | ColumncardSPEFCIEnable | read-write | mandatory | The atm EFCI marking enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.167 | ColumncardSPClpEnable | read-write | mandatory | The atm CLP-1 enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.168 | ColumnspATMTcaId | read-only | mandatory | This object identifies the the most recently declared sp ATM threshold crossing alert and first byte is used to indicate the switching port number. i.e. sp 1 h… |
| 1.3.6.1.4.1.277.1.7.2.1.169 | ColumncardSubcardToRedundant | read-write | mandatory | Commands the card to initiate an immediate protection switch on the identified subcard that it controls. This causes control to be switched from the active car… |
| 1.3.6.1.4.1.277.1.7.2.1.170 | ColumncardMemory5Usage | read-only | mandatory | The bank5 memory utilization, in terms of free bytes, for CP Oynx card only. |
| 1.3.6.1.4.1.277.1.7.2.1.171 | ColumncardSF1OperStatus | read-only | mandatory | The current status of Switch Fabric 1 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.172 | ColumncardSF2OperStatus | read-only | mandatory | The current status of Switch Fabric 2 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.173 | ColumncardTM1OperStatus | read-only | mandatory | The current status of Timing Module 1 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.174 | ColumncardTM2OperStatus | read-only | mandatory | The current status of Timing Module 2 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.175 | ColumncardMemStartLog | read-write | mandatory | |
| 1.3.6.1.4.1.277.1.7.2.1.176 | ColumncardMemLogLevel | read-write | mandatory | Set the Memory log level. Default 6 |
| 1.3.6.1.4.1.277.1.7.2.1.177 | ColumncardMemClrLog | read-write | mandatory | |
| 1.3.6.1.4.1.277.1.7.2.1.178 | ColumncardValidSubcards | read-only | mandatory | The number of manageable subcards physically present in this card. |
| 1.3.6.1.4.1.277.1.7.2.1.179 | ColumncardClp0CbrThreshold | read-write | mandatory | The CLP 0 threshold for CBR queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the thre… |
| 1.3.6.1.4.1.277.1.7.2.1.180 | ColumncardClp01CbrThreshold | read-write | mandatory | The maximum length of CBR queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.181 | ColumncardClp0VbrRtThreshold | read-write | mandatory | The CLP 0 threshold for VBR RT queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the t… |
| 1.3.6.1.4.1.277.1.7.2.1.182 | ColumncardClp01VbrRtThreshold | read-write | mandatory | The maximum length of VBR-RT queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshol… |
| 1.3.6.1.4.1.277.1.7.2.1.183 | ColumncardClp0VbrNrtThreshold | read-write | mandatory | The CLP 0 threshold for VBR NRT queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the … |
| 1.3.6.1.4.1.277.1.7.2.1.184 | ColumncardClp01VbrNrtThreshold | read-write | mandatory | The maximum length of VBR-NRT queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this thresho… |
| 1.3.6.1.4.1.277.1.7.2.1.185 | ColumncardClp0UAbrThreshold | read-write | mandatory | The CLP 0 threshold for ABR/UBR queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the … |
| 1.3.6.1.4.1.277.1.7.2.1.186 | ColumncardClp01UAbrThreshold | read-write | mandatory | The maximum length of UBR/ABR queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this thresho… |
| 1.3.6.1.4.1.277.1.7.2.1.187 | ColumncardControlMessagesFromBus | read-write | mandatory | The number of complete control Messages received over the Cell Bus for this card. |
| 1.3.6.1.4.1.277.1.7.2.1.188 | ColumncardControlMessagesToBus | read-write | mandatory | The number of complete control Messages transmitted by this card over the Cell Bus. |
| 1.3.6.1.4.1.277.1.7.2.1.189 | ColumncardBTUsFromBus | read-write | mandatory | The number of BTUs received by this card over the Cell Bus. |
| 1.3.6.1.4.1.277.1.7.2.1.190 | ColumncardBTUsToBus | read-write | mandatory | The number of BTUs transmitted by this card over the Cell Bus. |
| 1.3.6.1.4.1.277.1.7.2.1.191 | ColumncardInvalidPvcBTUs | read-write | mandatory | The number of BTUs received by this card over the Cell Bus with an invalid PVC identifier. |
| 1.3.6.1.4.1.277.1.7.2.1.192 | ColumncardIncompleteFramesFromBus | read-write | mandatory | The number of partial frames received by this card over the Cell Bus which were discarded due to missing BTUs. |
| 1.3.6.1.4.1.277.1.7.2.1.193 | ColumncardBTUsBusErrors | read-write | mandatory | The number of BTUs received by this card over the Cell Bus which were discarded due to errors. |
| 1.3.6.1.4.1.277.1.7.2.1.194 | ColumncardBTUsNoResource | read-write | mandatory | The number of BTUs received by this card over the Cell Bus which were discarded due to no free BTUs available to replace it. |
| 1.3.6.1.4.1.277.1.7.2.1.195 | ColumncardInvalidPvcBTUsThreshold | read-write | mandatory | Send trap if the number of BTUs received by this card over the Cell Bus with an invalid PVC identifier exceeds this in a one minute interval. Zero value implie… |
| 1.3.6.1.4.1.277.1.7.2.1.196 | ColumncardIncompleteFramesFromBusThreshold | read-write | mandatory | Send trap if the number of partial frames received by this card over the Cell Bus which were discarded due to missing BTUs exceeds this in a one minute interva… |
| 1.3.6.1.4.1.277.1.7.2.1.197 | ColumncardBTUsBusErrorThreshold | read-write | mandatory | Send trap if the number of BTUs received by this card over the Cell Bus which were discarded due to errors exceeds this in a one minute interval. Zero value im… |
| 1.3.6.1.4.1.277.1.7.2.1.198 | ColumncardBTUsNoResourceThreshold | read-write | mandatory | Send trap if the number of BTUs received by this card over the Cell Bus which were discarded due to no free BTUs available to replace it exceeds this in a one … |
| 1.3.6.1.4.1.277.1.7.2.1.199 | ColumncardFrameMemoryThreshold | read-write | mandatory | The percentage of frame memory utilization on this card which will generate a trap. Zero value implies no check. |
| 1.3.6.1.4.1.277.1.7.2.1.200 | ColumncardHoldQFrameMemory | read-only | mandatory | The frame memory utilization, in terms of bytes, currently on the Hold Queues for this card. |
| 1.3.6.1.4.1.277.1.7.2.1.201 | ColumncardTotalAAL5RxErrorCount | read-only | mandatory | The total number of Rx errors detected by the AAL5 processor on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.202 | ColumncardOperMemSize | read-only | mandatory | The total memory size on this card, in MB (1024 Kbytes). |
| 1.3.6.1.4.1.277.1.8 | Nodeds1 | |||
| 1.3.6.1.4.1.277.1.8 | NodenodeSwDownloadFailed | This trap indicates that a software download failed. | ||
| 1.3.6.1.4.1.277.1.8.1 | Tabledsx1ConfigTable | not-accessible | mandatory | The DS1 Configuration table. |
| 1.3.6.1.4.1.277.1.8.1.1 | Rowdsx1ConfigEntry | not-accessible | mandatory | An entry in the DS1 Configuration table. |
| 1.3.6.1.4.1.277.1.8.1.1.1 | Columndsx1SlotId | read-only | mandatory | The slot number of the corresponding DS1. |
| 1.3.6.1.4.1.277.1.8.1.1.2 | Columndsx1PortId | read-only | mandatory | The port number of the corresponding DS1 on the board. |
| 1.3.6.1.4.1.277.1.8.1.1.3 | Columndsx1TimeElapsed | read-only | mandatory | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.4.1.277.1.8.1.1.4 | Columndsx1ValidIntervals | read-only | mandatory | The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in… |
| 1.3.6.1.4.1.277.1.8.1.1.5 | Columndsx1LineType | read-only | mandatory | This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reaso… |
| 1.3.6.1.4.1.277.1.8.1.1.6 | Columndsx1LineCoding | read-only | mandatory | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS refers the Jamme… |
| 1.3.6.1.4.1.277.1.8.1.1.7 | Columndsx1SendCode | read-only | mandatory | This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data… |
| 1.3.6.1.4.1.277.1.8.1.1.8 | Columndsx1CircuitIdentifier | read-only | mandatory | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.4.1.277.1.8.1.1.9 | Columndsx1LoopbackConfig | read-only | mandatory | This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a reque… |
| 1.3.6.1.4.1.277.1.8.1.1.10 | Columndsx1LineStatus | read-only | mandatory | This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. The dsx1Line… |
| 1.3.6.1.4.1.277.1.8.1.1.11 | Columndsx1SignalMode | read-only | mandatory | 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Sig- naling is in use. 'bitOriented' indicat… |
| 1.3.6.1.4.1.277.1.8.1.1.12 | Columndsx1TransmitClockSource | read-only | mandatory | The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local cloc… |
| 1.3.6.1.4.1.277.1.8.1.1.13 | Columndsx1Fdl | read-only | mandatory | This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following i… |
| 1.3.6.1.4.1.277.1.8.1.1.14 | Columndsx1FdlVersion | read-only | mandatory | The version of the Dallas FDL firmware |
| 1.3.6.1.4.1.277.1.8.2 | Tabledsx1CurrentTable | not-accessible | mandatory | The DS1 Current table. |
| 1.3.6.1.4.1.277.1.8.2.1 | Rowdsx1CurrentEntry | not-accessible | mandatory | An entry in the DS1 Current table. |
| 1.3.6.1.4.1.277.1.8.2.1.1 | Columndsx1CurrentSlotId | read-only | mandatory | The slot number of the corresponding DS1. |
| 1.3.6.1.4.1.277.1.8.2.1.2 | Columndsx1CurrentPortId | read-only | mandatory | The port number of the corresponding DS1 on the board. |
| 1.3.6.1.4.1.277.1.8.2.1.3 | Columndsx1CurrentESs | read-only | mandatory | The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute inter- val. |
| 1.3.6.1.4.1.277.1.8.2.1.4 | Columndsx1CurrentSESs | read-only | mandatory | The number of Severely Errored Seconds encoun- tered by a DS1 interface in the current 15 minute interval. |
| 1.3.6.1.4.1.277.1.8.2.1.5 | Columndsx1CurrentSEFSs | read-only | mandatory | The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute interval. |
| 1.3.6.1.4.1.277.1.8.2.1.6 | Columndsx1CurrentUASs | read-only | mandatory | The number of Unavailable Seconds encountered by a DS1 interface in the current 15 minute in- terval. |
| 1.3.6.1.4.1.277.1.8.2.1.7 | Columndsx1CurrentCSSs | read-only | mandatory | The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the current 15 minute interval. |
| 1.3.6.1.4.1.277.1.8.2.1.8 | Columndsx1CurrentBESs | read-only | mandatory | The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current 15 minute interval. |
| 1.3.6.1.4.1.277.1.8.3 | Tabledsx1IntervalTable | not-accessible | mandatory | The DS1 Interval table. |
| 1.3.6.1.4.1.277.1.8.3.1 | Rowdsx1IntervalEntry | not-accessible | mandatory | An entry in the DS1 Interval table. |
| 1.3.6.1.4.1.277.1.8.3.1.1 | Columndsx1IntervalSlotId | read-only | mandatory | The slot number of the corresponding DS1. |
| 1.3.6.1.4.1.277.1.8.3.1.2 | Columndsx1IntervalPortId | read-only | mandatory | The port number of the corresponding DS1 on the board. |
| 1.3.6.1.4.1.277.1.8.3.1.3 | Columndsx1IntervalNumber | read-only | mandatory | A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming tha… |
| 1.3.6.1.4.1.277.1.8.3.1.4 | Columndsx1IntervalESs | read-only | mandatory | The number of Errored Seconds encountered by a DS1 interface in one of the previous 96, indi- vidual 15 minute, intervals. |
| 1.3.6.1.4.1.277.1.8.3.1.5 | Columndsx1IntervalSESs | read-only | mandatory | The number of Severely Errored Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.277.1.8.3.1.6 | Columndsx1IntervalSEFSs | read-only | mandatory | The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.277.1.8.3.1.7 | Columndsx1IntervalUASs | read-only | mandatory | The number of Unavailable Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.277.1.8.3.1.8 | Columndsx1IntervalCSSs | read-only | mandatory | The number of Controlled Slip Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.277.1.8.3.1.9 | Columndsx1IntervalBESs | read-only | mandatory | The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.277.1.8.4 | Tabledsx1TotalTable | not-accessible | mandatory | The DS1 Total table. 24 hour interval. |
| 1.3.6.1.4.1.277.1.8.4.1 | Rowdsx1TotalEntry | not-accessible | mandatory | An entry in the DS1 Total table. |
| 1.3.6.1.4.1.277.1.8.4.1.1 | Columndsx1TotalSlotId | read-only | mandatory | The slot number of the corresponding DS1. |
| 1.3.6.1.4.1.277.1.8.4.1.2 | Columndsx1TotalPortId | read-only | mandatory | The port number of the corresponding DS1 on the board. |
| 1.3.6.1.4.1.277.1.8.4.1.3 | Columndsx1TotalESs | read-only | mandatory | The number of Errored Seconds encountered by a DS1 interface in the previous 24 hour interval |
| 1.3.6.1.4.1.277.1.8.4.1.4 | Columndsx1TotalSESs | read-only | mandatory | The number of Severely Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval. |
| 1.3.6.1.4.1.277.1.8.4.1.5 | Columndsx1TotalSEFSs | read-only | mandatory | The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24 hour interval. |
| 1.3.6.1.4.1.277.1.8.4.1.6 | Columndsx1TotalUASs | read-only | mandatory | The number of Unavailable Seconds encountered by a DS1 interface in the previous 24 hour in- terval. |
| 1.3.6.1.4.1.277.1.8.4.1.7 | Columndsx1TotalCSSs | read-only | mandatory | The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the previous 24 hour interval. |
| 1.3.6.1.4.1.277.1.8.4.1.8 | Columndsx1TotalBESs | read-only | mandatory | The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24 hour interval. |
| 1.3.6.1.4.1.277.1.9 | NodenodePrDownloadComplete | This trap indicates that a PRAM download was complete. | ||
| 1.3.6.1.4.1.277.1.10 | NodenodePrDownloadFailed | This trap indicates that a PRAM download failed. | ||
| 1.3.6.1.4.1.277.1.11 | NodenodeTracefull | This trap indicates that the node trace table was full and has been copied to a TFTP buffer awaiting to be xfered to the NMS. | ||
| 1.3.6.1.4.1.277.1.12 | NodenodeDiagLogfull | This trap indicates that the diagnostic log table was full and has been copied to a TFTP buffer awaiting to be xfered to the NMS. | ||
| 1.3.6.1.4.1.277.1.13 | NodenodeFlashMemErr | This trap indicates that a checksum or CRC-32 error occurred in Flash. | ||
| 1.3.6.1.4.1.277.1.14 | NodenodePramErr | This trap indicates that a checksum error or battery problem occurred in PRAM. | ||
| 1.3.6.1.4.1.277.1.15 | NodenodeRamErr | This trap indicates that an I/O error occurred in DRAM or SRAM. | ||
| 1.3.6.1.4.1.277.1.16 | NodenodeInternalErr | This trap indicates that a fatal internal hardware or software error encountered and system needs to be re-booted. | ||
| 1.3.6.1.4.1.277.1.17 | NodepportStatusChange | This trap indicates that the indicated physical port has changed state. | ||
| 1.3.6.1.4.1.277.1.18 | NodelportCongests | This trap indicates that the rate of entering severely and absolutely congested state on the indicated logical port has exceeded the threshold. | ||
| 1.3.6.1.4.1.277.1.19 | NodetrkStatusChange | This trap indicates that the trunk associated with the indicated logical port has changed state. | ||
| 1.3.6.1.4.1.277.1.20 | NodecktDlciStatusChange | This trap indicates that the user-to-user PVC state has been changed for this virtual circuit. It has either been created or invalidated, or has toggled betwee… | ||
| 1.3.6.1.4.1.277.1.21 | NodecktDlciReroute | This trap indicates that a PVC has been re-routed. | ||
| 1.3.6.1.4.1.277.1.22 | NodepportInterfaceMismatch | This trap indicates the actual physical interface is different than the configured physical interface. | ||
| 1.3.6.1.4.1.277.1.23 | NodelportErrorExceedThreshold | This trap indicates the frame errors per minute on this lport exceeded the threshold. | ||
| 1.3.6.1.4.1.277.1.24 | NodenodeErrorReport | A component in the switch discovered a non-fatal error condition. | ||
| 1.3.6.1.4.1.277.1.25 | NodecktGrpStatusChange | Circuits on interfaces go up or down. | ||
| 1.3.6.1.4.1.277.1.26 | NodenodeUserLogin | An user has logged in STDX through either serial console or telnet. | ||
| 1.3.6.1.4.1.277.1.27 | NodenodeUserLogout | An user has logged out. | ||
| 1.3.6.1.4.1.277.1.28 | NodecardUp | This trap indicates that an intelligent card has transitioned to an ACTIVE state. | ||
| 1.3.6.1.4.1.277.1.29 | NodecardDown | This trap indicates that an intelligent card has transitioned to a NON-ACTIVE state. | ||
| 1.3.6.1.4.1.277.1.30 | NodelnkStatusChange | This trap indicates that the link status (Link protocol) associated with the indicated logical port has changed state. | ||
| 1.3.6.1.4.1.277.1.31 | NodelnkSmdsHbpNaTca | This trap indicates that non-Ack count for SMDS DXI heartbeat poll exceedes the threshold. The non-Ack count is reset every 15 minutes. | ||
| 1.3.6.1.4.1.277.1.32 | NodelnkSmdsDiscardTca | This trap indicates that Total Discard packet count for SMDS packet exceedes the threshold. ( This trap has not been implemented in this release yet ). | ||
| 1.3.6.1.4.1.277.1.33 | NodecardRedundSwitchOver | This trap indicates that the card in the specified slot has shot its active partner and has become the active card of the pair. | ||
| 1.3.6.1.4.1.277.1.34 | NodecardErrorReport | The specified card discovered a non-fatal error condition. | ||
| 1.3.6.1.4.1.277.1.35 | NodesvcSetup | This trap is generated by the ingress switch whenever a Frame Relay Svc is setup or cleared. cktStatus indicates whether it is a setup or a clearing. | ||
| 1.3.6.1.4.1.277.1.36 | NodesvcClearing | Reserved for Frame Relay SVC. | ||
| 1.3.6.1.4.1.277.1.37 | NodesvcFailure | This trap is generated by the ingress switch whenever a Frame Relay svc setup fails. cktSvcCause contains the cause number. | ||
| 1.3.6.1.4.1.277.1.38 | NodetrkBuAttempt | This trap indicates that an attempt to establish the backup trunk associated with the indicated logical port is being made. | ||
| 1.3.6.1.4.1.277.1.39 | NodetrkBuFailure | This trap indicates that the primary trunk associated with the indicated logical port has not been backed up or the backup trunk associated with the indicated … | ||
| 1.3.6.1.4.1.277.1.40 | NodetrkBuReleased | This trap indicates that the backup trunk associated with the indicated logical port has been released. | ||
| 1.3.6.1.4.1.277.1.41 | NodepportDS0LoopUpChange | This trap indicates one or more DS0's have gone into loopback.pportDS0LoopUpStatus reports the DS0's that have gone into loopback. | ||
| 1.3.6.1.4.1.277.1.42 | NodepportDS0LoopDownChange | This trap indicates one or more DS0's have gone out of loopback.pportDS0LoopDownStatus reports the DS0's that have gone out of loopback. | ||
| 1.3.6.1.4.1.277.1.43 | NodelportISDNCallRej | This trap indicates that a call has been rejected due either the inability to authenticate the call or lack of B-channel pool resources. | ||
| 1.3.6.1.4.1.277.1.44 | Nodepportdsx3LoopChange | This trap indicates when the DS3 or E3 has changed its current loopback state. | ||
| 1.3.6.1.4.1.277.1.45 | Nodepportds1LoopChange | This trap indicates when the DS1 has changed its current loopback state. | ||
| 1.3.6.1.4.1.277.1.46 | NodepportExtClockBackup | This trap indicates that a pport has lost the external clock source and is switching over to the backup clock selected. | ||
| 1.3.6.1.4.1.277.1.47 | NodepportExtClockRestore | This trap indicates that external clock is recovered and the pport will switch back to external clock. | ||
| 1.3.6.1.4.1.277.1.48 | NodepportExtClkCapabilityMismatch | This trap indicates the port on this card (and the card itself) is not capable of running external clock. | ||
| 1.3.6.1.4.1.277.1.50 | NodenodeBillingUsageRecOvflWarning | Warning that a usage record counter-value overflow condition has occurred while aggregating usage data recently collected from one or more IOPs. An overflow co… | ||
| 1.3.6.1.4.1.277.1.51 | NodenodeBillingUsageRecCrFailed | Notification that a usage record could not be created. | ||
| 1.3.6.1.4.1.277.1.52 | NodenodeBillingStateChange | Notification that billing has been enabled or disabled on the switch. This trap is generated at switch boot or when the value of the nodeBilling object is modi… | ||
| 1.3.6.1.4.1.277.1.53 | NodelportBillingStateChange | Notification that billing has been enabled or disabled on a particular logical port. This trap is generated the value of the lportBilling is modified for a par… | ||
| 1.3.6.1.4.1.277.1.54 | NodenodeBillingSwAPCommsFailure | Notification that switch to Adjunct Processor communication has failed and that a usage file transfer has failed to complete. | ||
| 1.3.6.1.4.1.277.1.57 | NodelportCBRLineDataError | This trap indicates the error state of the CBR lport. | ||
| 1.3.6.1.4.1.277.1.58 | NodeclkSourceSwitch | This trap indicates that the CBR port switched its clock method. | ||
| 1.3.6.1.4.1.277.1.59 | NodeclkSourceFailure | This trap indicates that the clock generation unit switched between holdover mode and synchronization to reference clock. | ||
| 1.3.6.1.4.1.277.1.60 | NodelportSmdsSip3SaNotFoundTca | This trap indicates that the number of Sa Not Found violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.61 | NodelportSmdsSip3SaDaOnSamePortTca | This trap indicates that the number of Sa Da On Same Port violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.62 | NodelportSmdsSip3DstGaNotFoundTca | This trap indicates that the number of Dst Ga Not Found violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.63 | NodelportSmdsSip3DstIaScrnFailTca | This trap indicates that the number of Dst Ia Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.64 | NodelportSmdsSip3SaValFailTca | This trap indicates that the number of Sa Val Fail violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.65 | NodelportSmdsSip3DstIaNotFoundTca | This trap indicates that the number of Dst Ia Not Found violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.66 | NodelportSmdsSip3SrcIaScrnFailTca | This trap indicates that the number of Src Ia Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.67 | NodelportSmdsSip3DstGaScrnFailTca | This trap indicates that the number of Dst Ga Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.68 | NodelportSmdsDxi2LinkIdInvalidTca | This trap indicates that the number of Link Id Invalid violations exceeded the specified Smds pdu violation threshold for the logical port. | ||
| 1.3.6.1.4.1.277.1.69 | NodenodePrimarySyncReferenceChange | Notification that the Primary Synchronization Reference operational state has changed. | ||
| 1.3.6.1.4.1.277.1.70 | NodenodeSecondarySyncReferenceChange | Notification that the Secondary Synchronization Reference operational state has changed. | ||
| 1.3.6.1.4.1.277.1.71 | NodenodeExternalClockAChange | Notification that the External Reference Clock A operational state has changed. | ||
| 1.3.6.1.4.1.277.1.72 | NodenodeExternalClockBChange | Notification that the External Reference Clock B operational state has changed. | ||
| 1.3.6.1.4.1.277.1.73 | NodenodePortReferenceAChange | Notification that the Port Reference Clock A operational state has changed. | ||
| 1.3.6.1.4.1.277.1.74 | NodenodePortReferenceBChange | Notification that the Port Reference Clock B operational state has changed. | ||
| 1.3.6.1.4.1.277.1.75 | NodepportDS0InitiateLpbkFailure | This trap indicates that the DS0 requested to be set into far end loopback has failed to do so. | ||
| 1.3.6.1.4.1.277.1.76 | NodepportDS0InitiateLpbkSuccess | This trap indicates that the DS0 requested to be set into far end loopback has succeeded. | ||
| 1.3.6.1.4.1.277.1.77 | NodelportISDNIpAddrRej | This trap indicates that an Ip Address assignment failed. | ||
| 1.3.6.1.4.1.277.1.78 | NodecktAtmStatusChange | This trap indicates that the user-to-user ATM PVC state has been changed for this virtual circuit. It has either been created or invalidated, or has toggled be… | ||
| 1.3.6.1.4.1.277.1.79 | NodecktAtmReroute | This trap indicates that an ATM PVC has been re-routed. | ||
| 1.3.6.1.4.1.277.1.80 | NodecardTransmitClockStatusChange | This trap indicates the IOM transmit clock synchronization status has chnaged. | ||
| 1.3.6.1.4.1.277.1.81 | NodecardSystemPrimaryClockStatusChange | This trap indicates that the IOM system primary clock reference status has changed. | ||
| 1.3.6.1.4.1.277.1.82 | NodecardSystemSecondaryClockStatusChange | This trap indicates that the IOM system primary clock reference status has changed. | ||
| 1.3.6.1.4.1.277.2 | Nodecascsmds | |||
| 1.3.6.1.4.1.277.2.1 | Nodesmdsaddr | |||
| 1.3.6.1.4.1.277.2.1.1 | TablesmdsaddrTable | not-accessible | mandatory | A list of smds adress entries. |
| 1.3.6.1.4.1.277.2.1.1.1 | RowsmdsaddrEntry | not-accessible | mandatory | An smds address and its associated information. |
| 1.3.6.1.4.1.277.2.1.1.1.1 | ColumnsmdsaddrAddr | read-write | mandatory | SMDS address. The 4 most significant bits are the address type : 1100 for an individual address, 1110 for a group address. The following 4 bits are 0001. The f… |
| 1.3.6.1.4.1.277.2.1.1.1.2 | ColumnsmdsaddrType | read-write | mandatory | SMDS address internal type. |
| 1.3.6.1.4.1.277.2.1.1.1.3 | ColumnsmdsaddrId | read-write | mandatory | smds address internal ID. Range from 1 to 192 for local individual addresses. Range from 193 to 704 for Alien individual addresses. Range from 1 to 64 for loca… |
| 1.3.6.1.4.1.277.2.1.1.1.4 | ColumnsmdsaddrIf | read-write | mandatory | The interface to which this address is assigned. |
| 1.3.6.1.4.1.277.2.1.1.1.5 | ColumnsmdsaddrParentGrpMap | read-only | mandatory | The parent group bit map. The bit position of each bit in this bit map represent a parent group address ID. The most significant bit is corresponding to group … |
| 1.3.6.1.4.1.277.2.1.1.1.6 | ColumnsmdsaddrParentScrnMap | read-only | mandatory | This MIB object not applicable to switch software versions 03.99.00 and above. The parent screen bit map. The bit position of each bit in this bit map represen… |
| 1.3.6.1.4.1.277.2.1.1.1.7 | ColumnsmdsaddrMemberAddrMap | read-write | mandatory | The member individual address bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. Th… |
| 1.3.6.1.4.1.277.2.1.1.1.8 | ColumnsmdsaddrAdminStatus | read-write | mandatory | administration status |
| 1.3.6.1.4.1.277.2.1.1.1.9 | ColumnsmdsaddrSlot | read-write | mandatory | The Slot in which this address is assigned. |
| 1.3.6.1.4.1.277.2.1.1.1.10 | ColumnsmdsaddrSsiIfNum | read-write | mandatory | The SSI to which this address is associated. |
| 1.3.6.1.4.1.277.3 | Nodenamebinding | |||
| 1.3.6.1.4.1.277.3.1 | TablenamebindingTable | not-accessible | mandatory | A table of name bindings to a set of logical ports. |
| 1.3.6.1.4.1.277.3.1.1 | RownamebindingEntry | not-accessible | mandatory | The name binding entry contains objects relative to a name binding. |
| 1.3.6.1.4.1.277.3.1.1.1 | ColumnnameType | read-write | mandatory | The name type. |
| 1.3.6.1.4.1.277.3.1.1.2 | ColumnnameName | read-write | mandatory | A name of the type indicated by nameType. |
| 1.3.6.1.4.1.277.3.1.1.3 | ColumnnamePrimary | read-write | mandatory | The current binding type for this entry. |
| 1.3.6.1.4.1.277.3.1.1.4 | ColumnnameIfIndex | read-write | mandatory | The interface number of the logical port for this binding. |
| 1.3.6.1.4.1.277.3.1.1.5 | ColumnnameNodeId | read-only | mandatory | The identifier number of the node for this binding. |
| 1.3.6.1.4.1.277.3.1.1.6 | ColumnnameStatus | read-write | mandatory | The status of the binding. |
| 1.3.6.1.4.1.277.4 | Nodeisdnaddr | |||
| 1.3.6.1.4.1.277.4.1 | TableisdnAddrTable | not-accessible | mandatory | A list of E.164 address entries. |
| 1.3.6.1.4.1.277.4.1.1 | RowisdnAddrEntry | not-accessible | mandatory | Information about a single local E.164 address in the table. Setting this varible to 0 removes the entry. |
| 1.3.6.1.4.1.277.4.1.1.1 | ColumnisdnAddrIf | read-write | mandatory | The interface id of the logical port in question |
| 1.3.6.1.4.1.277.4.1.1.2 | ColumnisdnAddr | read-write | mandatory | ISDN address. The actual E164 number. For example, ISDN address 15086922600 is stored as string 15086922600. Setting this value to a null string removes this e… |
| 1.3.6.1.4.1.277.4.1.1.3 | ColumnisdnChanType | read-write | mandatory | type of logical port 0 => isdn b-channel, 1 => sw56 |
| 1.3.6.1.4.1.277.4.2 | TableisdnCallerIDTable | not-accessible | mandatory | A list of valid caller ids |
| 1.3.6.1.4.1.277.4.2.1 | RowisdnCallerIDEntry | not-accessible | mandatory | Information about a single valid caller id. |
| 1.3.6.1.4.1.277.4.2.1.1 | ColumnisdnCallerIDIf | read-write | mandatory | The interface id of the logical port in question |
| 1.3.6.1.4.1.277.4.2.1.2 | ColumnisdnCallerIDAddr | read-write | mandatory | ISDN address. The actual E164 number. For example, ISDN address 15086922600 is stored as string 15086922600. |
| 1.3.6.1.4.1.277.4.2.1.3 | ColumnisdnCallerAdminStatus | read-write | mandatory | administration status |
| 1.3.6.1.4.1.277.5 | Nodecascsvc | |||
| 1.3.6.1.4.1.277.5.1 | Nodesvcaddress | |||
| 1.3.6.1.4.1.277.5.1.1 | TablesvcNodePrefixTable | not-accessible | mandatory | A table of prefixes associated with this node. |
| 1.3.6.1.4.1.277.5.1.1.1 | RowsvcNodePrefixEntry | not-accessible | mandatory | The node prefix entry contains objects relevant to SVC prefixes associated with the node. |
| 1.3.6.1.4.1.277.5.1.1.1.1 | ColumnsvcNodePrefixPrefix | read-only | mandatory | A prefix associated with this node. E.164 prefixes are coded as 1-15 ASCII octets with no leading padding required. ATM endsystem prefixes are coded as 1-20 bi… |
| 1.3.6.1.4.1.277.5.1.1.1.2 | ColumnsvcNodePrefixNumBits | read-write | mandatory | The number of valid bits associated with this entry's prefix object. By default, this value will be 8 times the prefix object's octet string length. |
| 1.3.6.1.4.1.277.5.1.1.1.3 | ColumnsvcNodePrefixNmbPlan | read-write | mandatory | The numbering plan corresponding to this entry's prefix object. |
| 1.3.6.1.4.1.277.5.1.1.1.4 | ColumnsvcNodePrefixAdminStatus | read-write | mandatory | The status of this entry. |
| 1.3.6.1.4.1.277.5.1.2 | TablesvcPrefixTable | not-accessible | mandatory | A table of SVC address prefixes associated with ports on this node. |
| 1.3.6.1.4.1.277.5.1.2.1 | RowsvcPrefixEntry | not-accessible | mandatory | The prefix entry contains objects relevant to SVC prefixes associated with this port. |
| 1.3.6.1.4.1.277.5.1.2.1.1 | ColumnsvcPrefixIfIndex | read-only | mandatory | The interface value of the corresponding MIB-II ifEntry. |
| 1.3.6.1.4.1.277.5.1.2.1.2 | ColumnsvcPrefixPrefix | read-only | mandatory | A prefix associated with this port. E.164 prefixes are coded as 1-15 ASCII octets with no leading padding required. ATM endsystem prefixes are coded as 1-20 bi… |
| 1.3.6.1.4.1.277.5.1.2.1.3 | ColumnsvcPrefixNumBits | read-write | mandatory | The number of valid bits associated with this entry's prefix object. By default, this value will be 8 times the prefix object's octet string length. |
| 1.3.6.1.4.1.277.5.1.2.1.4 | ColumnsvcPrefixNmbPlan | read-write | mandatory | The numbering plan corresponding to this entry's prefix object. |
| 1.3.6.1.4.1.277.5.1.2.1.5 | ColumnsvcPrefixAdminCost | read-write | mandatory | This object is only relevant for ports connecting this network to another network and is used to represent the administrative cost of reaching destinations con… |
| 1.3.6.1.4.1.277.5.1.2.1.6 | ColumnsvcPrefixLocalGatewayAddress | read-write | mandatory | This object is only relevant for ports connecting this network to another network and is used to replace the calling party number when egress address translati… |
| 1.3.6.1.4.1.277.5.1.2.1.7 | ColumnsvcPrefixLocalGatewayNmbPlan | read-write | mandatory | The numbering plan corresponding to this entry's local gateway address object. |
| 1.3.6.1.4.1.277.5.1.2.1.8 | ColumnsvcPrefixRemoteGatewayAddress | read-write | mandatory | This object is only relevant for ports connecting this network to another network and is used to replace the calling party number when egress address translati… |
| 1.3.6.1.4.1.277.5.1.2.1.9 | ColumnsvcPrefixRemoteGatewayNmbPlan | read-write | mandatory | The numbering plan corresponding to this entry's remote gateway address object. |
| 1.3.6.1.4.1.277.5.1.2.1.10 | ColumnsvcPrefixAdminStatus | read-write | mandatory | The status of this entry. |
| 1.3.6.1.4.1.277.5.1.3 | TablesvcAddrTable | not-accessible | mandatory | A table of SVC addresses associated with with ports on this node. |
| 1.3.6.1.4.1.277.5.1.3.1 | RowsvcAddrEntry | not-accessible | mandatory | The address entry contains objects relevant to SVC addresses associated with this port. |
| 1.3.6.1.4.1.277.5.1.3.1.1 | ColumnsvcAddrIfIndex | read-only | mandatory | The interface value of the corresponding MIB-II ifEntry. |
| 1.3.6.1.4.1.277.5.1.3.1.2 | ColumnsvcAddrAddress | read-only | mandatory | An address associated with this port. E.164 addresses are coded as 1-15 ASCII octets. ATM-Endsystem addresses are coded as 20 binary octets. |
| 1.3.6.1.4.1.277.5.1.3.1.3 | ColumnsvcAddrNmbPlan | read-write | mandatory | The numbering plan corresponding to this entry's address object. |
| 1.3.6.1.4.1.277.5.1.3.1.4 | ColumnsvcAddrAdminStatus | read-write | mandatory | The status of this entry. |
| 1.3.6.1.4.1.277.5.1.4 | TablesvcAtmUserPartTable | not-accessible | mandatory | A table of partial SVC addresses associated with ports on this node, relevant only to ATM DTE ports for use in ILMI address registration. |
| 1.3.6.1.4.1.277.5.1.4.1 | RowsvcAtmUserPartEntry | not-accessible | mandatory | The user part entry contains objects relevant to partial SVC addresses associated with ATM DTE ports on this node. |
| 1.3.6.1.4.1.277.5.1.4.1.1 | ColumnsvcAtmUserPartIfIndex | read-only | mandatory | The interface value of the corresponding MIB-II ifEntry. |
| 1.3.6.1.4.1.277.5.1.4.1.2 | ColumnsvcAtmUserPartUserPart | read-only | mandatory | A partial ATM endsystem address associated with this ATM DTE port. It will be combined with ATM endsystem prefixes received from the peer DCE to form a full AT… |
| 1.3.6.1.4.1.277.5.1.4.1.3 | ColumnsvcAtmUserPartAdminStatus | read-write | mandatory | The status of this entry. |
| 1.3.6.1.4.1.277.5.2 | Nodesvcmgt | |||
| 1.3.6.1.4.1.277.5.2.1 | TablesvcConfigTable | not-accessible | mandatory | A table of SVC configuration paramaters associated with logical ports. The number of entries is given by the value of ifNumber in MIB-II. |
| 1.3.6.1.4.1.277.5.2.1.1 | RowsvcConfigEntry | not-accessible | mandatory | The SVC configuration entry contains objects relevant to SVC operation on a logical port. |
| 1.3.6.1.4.1.277.5.2.1.1.1 | ColumnsvcConfigIfIndex | read-only | mandatory | The ifIndex value of the corresponding ifEntry. |
| 1.3.6.1.4.1.277.5.2.1.1.2 | ColumnsvcConfigInitiateIdentStatsUpload | read-write | mandatory | Setting this object initiates a TFTP upload of SVC identification statistics to the specified IP address. These statistics may be used to identify SVC's of int… |
| 1.3.6.1.4.1.277.5.2.1.1.3 | ColumnsvcConfigCgPtyInsertionMode | read-write | mandatory | This object determines whether a statically configured address shall be inserted in the calling party address IE for calls entering the network at this port. |
| 1.3.6.1.4.1.277.5.2.1.1.4 | ColumnsvcConfigCgPtyInsertionAddress | read-write | mandatory | The calling party address to use in conjunction with the calling party insertion function. E.164 addresses are coded as 15 ASCII octets, utilizing leading ASCI… |
| 1.3.6.1.4.1.277.5.2.1.1.5 | ColumnsvcConfigCgPtyInsertionNmbPlan | read-write | mandatory | The numbering plan corresponding to this entry's calling party insertion address object. |
| 1.3.6.1.4.1.277.5.2.1.1.6 | ColumnsvcConfigCgPtyScreenMode | read-write | mandatory | The type of screening to perform on the calling party number for calls entering the network at this port. Screening will be conducted by performing a bit-wise … |
| 1.3.6.1.4.1.277.5.2.1.1.7 | ColumnsvcConfigEgressAddrXlateMode | read-write | mandatory | This object determines the type of address translation, if any to occur for calls exiting the network at this port. The tunnelling mode will screen the called … |
| 1.3.6.1.4.1.277.5.2.1.1.8 | ColumnsvcConfigIngressAddrXlateMode | read-write | mandatory | This object determines the type of address translation, if any to occur for calls entering the network at this port. The tunnelling mode reverses the actions o… |
| 1.3.6.1.4.1.277.5.2.1.1.9 | ColumnsvcConfigCgPtyPresentationMode | read-write | mandatory | This object controls the circumstances under which the calling party number shall be presented at the egress port of the network. |
| 1.3.6.1.4.1.277.5.2.2 | TablesvcAtmConfigTable | not-accessible | mandatory | A table of ATM signalling paramaters associated with ATM logical ports. The maximum number of entries is given by the value of ifNumber in MIB-II. |
| 1.3.6.1.4.1.277.5.2.2.1 | RowsvcAtmConfigEntry | not-accessible | mandatory | The SVC ATM configuration entry contains objects relevant to the configuration and monitoring of ATM signalling on an ATM logical port. |
| 1.3.6.1.4.1.277.5.2.2.1.1 | ColumnsvcAtmConfigIfIndex | read-only | mandatory | The ifIndex value of the corresponding ifEntry. |
| 1.3.6.1.4.1.277.5.2.2.1.2 | ColumnsvcAtmConfigAdminStatus | read-write | mandatory | The configured state of the ATM signalling function for this port. |
| 1.3.6.1.4.1.277.5.2.2.1.3 | ColumnsvcAtmConfigOperStatus | read-only | mandatory | The operational status of the signalling function on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.4 | ColumnsvcAtmConfigQ93bMaxRestart | read-write | mandatory | The maximum number of unacknowledged restarts to send before declaring a signalling failure. |
| 1.3.6.1.4.1.277.5.2.2.1.5 | ColumnsvcAtmConfigQ93bMaxStatEnq | read-write | mandatory | The maximum number of unacknowledged status enquiries to send before issuing a restart. |
| 1.3.6.1.4.1.277.5.2.2.1.6 | ColumnsvcAtmConfigQ93bT303 | read-write | mandatory | Protocol Timer T303, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.7 | ColumnsvcAtmConfigQ93bT308 | read-write | mandatory | Protocol Timer T308, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.8 | ColumnsvcAtmConfigQ93bT309 | read-write | mandatory | Protocol Timer T309, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.9 | ColumnsvcAtmConfigQ93bT310 | read-write | mandatory | Protocol Timer T310, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.10 | ColumnsvcAtmConfigQ93bT313 | read-write | mandatory | Protocol Timer T313, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.11 | ColumnsvcAtmConfigQ93bT316 | read-write | mandatory | Protocol Timer T316, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.12 | ColumnsvcAtmConfigQ93bT322 | read-write | mandatory | Protocol Timer T322, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.13 | ColumnsvcAtmConfigQ93bT398 | read-write | mandatory | Protocol Timer T398, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.14 | ColumnsvcAtmConfigQ93bT399 | read-write | mandatory | Protocol Timer T399, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.15 | ColumnsvcAtmConfigQ93bTotalConns | read-only | mandatory | The total number of SVC's established on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.16 | ColumnsvcAtmConfigQ93bActiveConns | read-only | mandatory | The number of SVC's present on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.17 | ColumnsvcAtmConfigQ93bLastCauseTx | read-only | mandatory | The last transmitted cause code for this port. |
| 1.3.6.1.4.1.277.5.2.2.1.18 | ColumnsvcAtmConfigQ93bLastCauseRx | read-only | mandatory | The last received cause code for this port. |
| 1.3.6.1.4.1.277.5.2.2.1.19 | ColumnsvcAtmConfigQ93bNumSetupPduTx | read-only | mandatory | The number of setup PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.20 | ColumnsvcAtmConfigQ93bNumSetupPduRx | read-only | mandatory | The number of setup PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.21 | ColumnsvcAtmConfigQ93bNumCallProcPduTx | read-only | mandatory | The number of call proceeding PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.22 | ColumnsvcAtmConfigQ93bNumCallProcPduRx | read-only | mandatory | The number of call proceeding PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.23 | ColumnsvcAtmConfigQ93bNumConnectPduTx | read-only | mandatory | The number of connect PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.24 | ColumnsvcAtmConfigQ93bNumConnectPduRx | read-only | mandatory | The number of connect PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.25 | ColumnsvcAtmConfigQ93bNumConnectAckPduTx | read-only | mandatory | The number of connect ack PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.26 | ColumnsvcAtmConfigQ93bNumConnectAckPduRx | read-only | mandatory | The number of connect ack PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.27 | ColumnsvcAtmConfigQ93bNumReleasePduTx | read-only | mandatory | The number of release PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.28 | ColumnsvcAtmConfigQ93bNumReleasePduRx | read-only | mandatory | The number of release PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.29 | ColumnsvcAtmConfigQ93bNumReleaseCmpltPduTx | read-only | mandatory | The number of release complete PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.30 | ColumnsvcAtmConfigQ93bNumReleaseCmpltPduRx | read-only | mandatory | The number of release complete PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.31 | ColumnsvcAtmConfigQ93bNumAddPtyPduTx | read-only | mandatory | The number of add party PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.32 | ColumnsvcAtmConfigQ93bNumAddPtyPduRx | read-only | mandatory | The number of add party PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.33 | ColumnsvcAtmConfigQ93bNumAddPtyAckPduTx | read-only | mandatory | The number of add party acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.34 | ColumnsvcAtmConfigQ93bNumAddPtyAckPduRx | read-only | mandatory | The number of add party acknowledge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.35 | ColumnsvcAtmConfigQ93bNumAddPtyRejPduTx | read-only | mandatory | The number of add party reject PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.36 | ColumnsvcAtmConfigQ93bNumAddPtyRejPduRx | read-only | mandatory | The number of add party reject PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.37 | ColumnsvcAtmConfigQ93bNumDropPtyPduTx | read-only | mandatory | The number of drop party PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.38 | ColumnsvcAtmConfigQ93bNumDropPtyPduRx | read-only | mandatory | The number of drop party PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.39 | ColumnsvcAtmConfigQ93bNumDropPtyAckPduTx | read-only | mandatory | The number of drop party acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.40 | ColumnsvcAtmConfigQ93bNumDropPtyAckPduRx | read-only | mandatory | The number of drop party acknowledge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.41 | ColumnsvcAtmConfigQ93bNumStatusEnqPduTx | read-only | mandatory | The number of status enquiry PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.42 | ColumnsvcAtmConfigQ93bNumStatusEnqPduRx | read-only | mandatory | The number of status enquiry PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.43 | ColumnsvcAtmConfigQ93bNumStatusPduTx | read-only | mandatory | The number of status PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.44 | ColumnsvcAtmConfigQ93bNumStatusPduRx | read-only | mandatory | The number of status PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.45 | ColumnsvcAtmConfigQ93bNumRestartPduTx | read-only | mandatory | The number of restart PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.46 | ColumnsvcAtmConfigQ93bNumRestartPduRx | read-only | mandatory | The number of restart PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.47 | ColumnsvcAtmConfigQ93bNumRestartAckPduTx | read-only | mandatory | The number of restart acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.48 | ColumnsvcAtmConfigQ93bNumRestartAckPduRx | read-only | mandatory | The number of restart acknowledge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.49 | ColumnsvcAtmConfigQSaalMaxCC | read-write | mandatory | The maximum number of unacknowledged transmitted control PDU's before declaring a loss of connection. |
| 1.3.6.1.4.1.277.5.2.2.1.50 | ColumnsvcAtmConfigQSaalMaxPD | read-write | mandatory | The maximum number of PDU's transmitted before a POLL PDU is transmitted. |
| 1.3.6.1.4.1.277.5.2.2.1.51 | ColumnsvcAtmConfigQSaalMaxStat | read-write | mandatory | The maximum number of list elements in a STAT PDU. |
| 1.3.6.1.4.1.277.5.2.2.1.52 | ColumnsvcAtmConfigQSaalTPoll | read-write | mandatory | The protocol timer corresponding to the polling function, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.53 | ColumnsvcAtmConfigQSaalTKeepalive | read-write | mandatory | The protocol timer corresponding to the keepalive function, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.54 | ColumnsvcAtmConfigQSaalTNoResponse | read-write | mandatory | The protocol timer corresponding to the response timeout function, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.55 | ColumnsvcAtmConfigQSaalTCC | read-write | mandatory | The protocol timer corresponding to the transmission of control PDU's, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.56 | ColumnsvcAtmConfigQSaalTIdle | read-write | mandatory | The protocol timer corresponding to the idle function for UNI 3.1, only, specified in milliseconds. |
| 1.3.6.1.4.1.277.5.2.2.1.57 | ColumnsvcAtmConfigQSaalNumDiscardTx | read-only | mandatory | The number of QSaal transmit discards on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.58 | ColumnsvcAtmConfigQSaalNumDiscardRx | read-only | mandatory | The number of QSaal receive discards on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.59 | ColumnsvcAtmConfigQSaalNumErrorTx | read-only | mandatory | The number of QSaal transmit errors on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.60 | ColumnsvcAtmConfigQSaalNumErrorRx | read-only | mandatory | The number of QSaal receive errors on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.61 | ColumnsvcAtmConfigQSaalNumBgnPduTx | read-only | mandatory | The number of begin PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.62 | ColumnsvcAtmConfigQSaalNumBgnPduRx | read-only | mandatory | The number of begin PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.63 | ColumnsvcAtmConfigQSaalNumBgakPduTx | read-only | mandatory | The number of begin acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.64 | ColumnsvcAtmConfigQSaalNumBgakPduRx | read-only | mandatory | The number of begin acknowledge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.65 | ColumnsvcAtmConfigQSaalNumBgrejPduTx | read-only | mandatory | The number of begin reject PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.66 | ColumnsvcAtmConfigQSaalNumBgrejPduRx | read-only | mandatory | The number of begin reject PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.67 | ColumnsvcAtmConfigQSaalNumEndPduTx | read-only | mandatory | The number of end PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.68 | ColumnsvcAtmConfigQSaalNumEndPduRx | read-only | mandatory | The number of end PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.69 | ColumnsvcAtmConfigQSaalNumEndakPduTx | read-only | mandatory | The number of end acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.70 | ColumnsvcAtmConfigQSaalNumEndakPduRx | read-only | mandatory | The number of end acknowldge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.71 | ColumnsvcAtmConfigQSaalNumRsPduTx | read-only | mandatory | The number of resynchronization PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.72 | ColumnsvcAtmConfigQSaalNumRsPduRx | read-only | mandatory | The number of resynchronization PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.73 | ColumnsvcAtmConfigQSaalNumRsakPduTx | read-only | mandatory | The number of resynchronization acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.74 | ColumnsvcAtmConfigQSaalNumRsakPduRx | read-only | mandatory | The number of resynchronization acknowldge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.75 | ColumnsvcAtmConfigQSaalNumErPduTx | read-only | mandatory | The number of error recovery PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.76 | ColumnsvcAtmConfigQSaalNumErPduRx | read-only | mandatory | The number of errror recovery PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.77 | ColumnsvcAtmConfigQSaalNumErakPduTx | read-only | mandatory | The number of error recovery acknowledge PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.78 | ColumnsvcAtmConfigQSaalNumErakPduRx | read-only | mandatory | The number of errror recovery acknowledge PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.79 | ColumnsvcAtmConfigQSaalNumSdPduTx | read-only | mandatory | The number of sequenced data PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.80 | ColumnsvcAtmConfigQSaalNumSdPduRx | read-only | mandatory | The number of sequenced data PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.81 | ColumnsvcAtmConfigQSaalNumPollPduTx | read-only | mandatory | The number of poll PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.82 | ColumnsvcAtmConfigQSaalNumPollPduRx | read-only | mandatory | The number of poll PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.83 | ColumnsvcAtmConfigQSaalNumStatPduTx | read-only | mandatory | The number of status PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.84 | ColumnsvcAtmConfigQSaalNumStatPduRx | read-only | mandatory | The number of status PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.85 | ColumnsvcAtmConfigQSaalNumUstatPduTx | read-only | mandatory | The number of unsolicited status PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.86 | ColumnsvcAtmConfigQSaalNumUstatPduRx | read-only | mandatory | The number of unsolicited status PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.87 | ColumnsvcAtmConfigQSaalNumUdPduTx | read-only | mandatory | The number of unnumbered user data PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.88 | ColumnsvcAtmConfigQSaalNumUdPduRx | read-only | mandatory | The number of unnumbered user data PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.89 | ColumnsvcAtmConfigQSaalNumMdPduTx | read-only | mandatory | The number of unnumbered management data PDU's transmitted on this port. |
| 1.3.6.1.4.1.277.5.2.2.1.90 | ColumnsvcAtmConfigQSaalNumMdPduRx | read-only | mandatory | The number of unnumbered management data PDU's received on this port. |
| 1.3.6.1.4.1.277.5.2.3 | TablesvcAtmFailedCallTable | not-accessible | mandatory | A table of objects describing the N most recent SVC failures per port, in FIFO order. |
| 1.3.6.1.4.1.277.5.2.3.1 | RowsvcAtmFailedCallEntry | not-accessible | mandatory | The failed call entry contains objects relevant to abnormal SVC call failures. |
| 1.3.6.1.4.1.277.5.2.3.1.1 | ColumnsvcAtmFailedCallIfIndex | read-only | mandatory | The interface value of the corresponding MIB-II ifEntry for the port at which this call failure was declared. |
| 1.3.6.1.4.1.277.5.2.3.1.2 | ColumnsvcAtmFailedCallIndex | read-only | mandatory | The instance number for this failed call at this port. |
| 1.3.6.1.4.1.277.5.2.3.1.3 | ColumnsvcAtmFailedCallDirection | read-only | mandatory | The direction of the failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.4 | ColumnsvcAtmFailedCallPduType | read-only | mandatory | The Pdu Type containing the cause IE. |
| 1.3.6.1.4.1.277.5.2.3.1.5 | ColumnsvcAtmFailedCallPduDirection | read-only | mandatory | Whether the terminating PDU was transmitted or received on this port. |
| 1.3.6.1.4.1.277.5.2.3.1.6 | ColumnsvcAtmFailedCallCause | read-only | mandatory | The failure cause contained in the cause IE. |
| 1.3.6.1.4.1.277.5.2.3.1.7 | ColumnsvcAtmFailedCallLocation | read-only | mandatory | The failure location contained in the cause IE. |
| 1.3.6.1.4.1.277.5.2.3.1.8 | ColumnsvcAtmFailedCallDiagnostic | read-only | mandatory | The diagnostic information contained in the cause IE. |
| 1.3.6.1.4.1.277.5.2.3.1.9 | ColumnsvcAtmFailedCallCreationTime | read-only | mandatory | The sysUpTime when this call was initiated. |
| 1.3.6.1.4.1.277.5.2.3.1.10 | ColumnsvcAtmFailedCallTerminationTime | read-only | mandatory | The sysUpTime when this call was terminated. |
| 1.3.6.1.4.1.277.5.2.3.1.11 | ColumnsvcAtmFailedCallFailureNodeId | read-only | mandatory | The node which caused the SVC failure. |
| 1.3.6.1.4.1.277.5.2.3.1.12 | ColumnsvcAtmFailedCallFailureIfIndex | read-only | mandatory | The port on the failure node which caused the SVC failure. |
| 1.3.6.1.4.1.277.5.2.3.1.13 | ColumnsvcAtmFailedCallCallingParty | read-only | mandatory | The calling party number for this failed call, if present. |
| 1.3.6.1.4.1.277.5.2.3.1.14 | ColumnsvcAtmFailedCallCalledParty | read-only | mandatory | The called party number for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.15 | ColumnsvcAtmFailedCallAtmTfdType | read-only | mandatory | The combination of forward traffic parameters for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.16 | ColumnsvcAtmFailedCallAtmTfdParam1 | read-only | mandatory | Forward traffic descriptor parameter 1 for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.17 | ColumnsvcAtmFailedCallAtmTfdParam2 | read-only | mandatory | Forward traffic descriptor parameter 2 for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.18 | ColumnsvcAtmFailedCallAtmTfdParam3 | read-only | mandatory | Forward traffic descriptor parameter 3 for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.19 | ColumnsvcAtmFailedCallAtmQosClass | read-only | mandatory | Forward QOS class for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.20 | ColumnsvcAtmFailedCallAtmRTfdType | read-only | mandatory | The combination of reverse traffic parameters for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.21 | ColumnsvcAtmFailedCallAtmRTfdParam1 | read-only | mandatory | Reverse traffic descriptor parameter 1 for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.22 | ColumnsvcAtmFailedCallAtmRTfdParam2 | read-only | mandatory | Reverse traffic descriptor parameter 2 for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.23 | ColumnsvcAtmFailedCallAtmRTfdParam3 | read-only | mandatory | Reverse traffic descriptor parameter 3 for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.24 | ColumnsvcAtmFailedCallAtmRQoSClass | read-only | mandatory | Reverse QOS class for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.25 | ColumnsvcAtmFailedCallBBearerClass | read-only | mandatory | Broadband bearer class for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.26 | ColumnsvcAtmFailedCallBBearerTfcType | read-only | mandatory | Broadband bearer traffic type for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.27 | ColumnsvcAtmFailedCallBBearerTmgRqmt | read-only | mandatory | Broadband bearer timing requirement for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.28 | ColumnsvcAtmFailedCallBBearerUplaneCfg | read-only | mandatory | Broadband bearer user plane configuration for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.29 | ColumnsvcAtmFailedCallBBearerClippingSusc | read-only | mandatory | Broadband bearer clipping susceptability for this failed call. |
| 1.3.6.1.4.1.277.5.2.3.1.30 | ColumnsvcAtmFailedCallAdminStatus | read-only | mandatory | All entries are initially invalid. Due to the FIFO nature of this table, once N entries have been created, all entries will always be valid. |
| 1.3.6.1.4.1.277.5.55 | NodesvcAtmFailedCall | Notification that one or more SVC call failures have been logged in the svcAtmFailedCallTable. | ||
| 1.3.6.1.4.1.277.5.56 | NodesvcAtmSigStatusChange | Notification that the status of the ATM signalling function has changed on the port. | ||
| 1.3.6.1.4.1.277.6 | Nodesoftware | |||
| 1.3.6.1.4.1.277.6.1 | TableswTable | not-accessible | mandatory | A list of swEntry's. The number of entries is given by the value of swCardNumber |
| 1.3.6.1.4.1.277.6.1.1 | RowswEntry | not-accessible | mandatory | The software entry contains objects describing the software cards. |
| 1.3.6.1.4.1.277.6.1.1.1 | ColumnswLogicalSlotId | read-only | mandatory | The logical slot number of this card. This is used as an index for the swTable. In redundant configurations, this can be the physical slot number of either red… |
| 1.3.6.1.4.1.277.6.1.1.2 | ColumnswRedundState | read-only | mandatory | The current redundancy state of this card. |
| 1.3.6.1.4.1.277.6.1.1.3 | ColumnswRevision | read-only | mandatory | The software revision number in the form (major.minor.maint.patch) where major == the major release number minor == the minor release number maint == a mainten… |
| 1.3.6.1.4.1.277.6.1.1.4 | ColumnswBuildID | read-only | mandatory | An identifier which uniquely identifies the software image within the scope of the release. The build ID is generated automatically through the build process a… |
| 1.3.6.1.4.1.277.6.1.1.5 | ColumnswBuildDate | read-only | mandatory | The date on which the software image was generated. |
| 1.3.6.1.4.1.277.6.1.1.6 | ColumnswBuildDescription | read-only | mandatory | A general description of the release. |
| 1.3.6.1.4.1.277.6.1.1.7 | ColumnswCopyrightNotice | read-only | mandatory | Legalese describing the Copyrights covering this software image. |
| 1.3.6.1.4.1.277.6.1.1.8 | ColumnswCapabilityMask | read-only | mandatory | A 32-bit integer which bitmaps optional or additional features supported by this software release. For use by the NMS in determining capabilities of the softwa… |
| 1.3.6.1.4.1.277.6.1.1.9 | ColumnswFeatureMask | read-only | mandatory | A 32-bit integer which bitmaps optional or additional features supported by this software release. For use by the NMS in determining capabilities of the softwa… |
| 1.3.6.1.4.1.277.6.1.1.10 | ColumnswPatchMask | read-only | mandatory | A 32-bit integer which bitmaps incremental patches which have been applied to the software release. The significance of this bitmap varies by release. For Casc… |
| 1.3.6.1.4.1.277.6.1.1.11 | ColumnswBuildUserId | read-only | mandatory | The user ID of the person responsible for generating the software image. For Cascade internal use. |
| 1.3.6.1.4.1.277.6.1.1.12 | ColumnswBuildView | read-only | mandatory | Source control information for image generation. For Cascade internal use. |
| 1.3.6.1.4.1.277.6.1.1.13 | ColumnswBuildConfigSpec | read-only | mandatory | Source control information for image generation. For Cascade internal use. |
| 1.3.6.1.4.1.277.9 | Nodeprovserver | |||
| 1.3.6.1.4.1.277.49 | NodenodeFileTransferReport | Reporting the outcome of a previous file transfer request. nodeFileTransferRequest specifies the request and nodeFileTransferStatus gives the outcome. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CardStatuses | INTEGER { | ||
| CardTypes | INTEGER { | ||
| Index | INTEGER |