CHIPCOMMIB
1416 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.49 | Nodechipcom | |||
| 1.3.6.1.4.1.49.1 | NodechipHello | A chipHello trap is sent every minute by an agent with the hello trap enabled. The hello trap will discontinue being sent when either the agent receives an aut… | ||
| 1.3.6.1.4.1.49.2 | NodechipSlotDown | This trap indicates that the module in the indicated slot is down. Usually, this trap is sent when the module has been removed. Sometimes, this trap is sent wh… | ||
| 1.3.6.1.4.1.49.2 | Nodechipmib02 | |||
| 1.3.6.1.4.1.49.2.1 | NodechipGen | |||
| 1.3.6.1.4.1.49.2.1.1 | ScalarchipGenProduct | read-only | mandatory | The product type represented by this agent. |
| 1.3.6.1.4.1.49.2.1.2 | ScalarchipGenServiceDate | read-only | mandatory | The date that the product was last serviced in the format yymmdd. If this date is unknown, the value of this object is '000000'. |
| 1.3.6.1.4.1.49.2.1.3 | ScalarchipGenNetman | read-only | mandatory | The IP (source) Address of the last authenticated SNMP PDU received by this entity before this request. An IP Address of 00.00.00.00 represents the default val… |
| 1.3.6.1.4.1.49.2.1.4 | ScalarchipGenDiagnostics | read-only | mandatory | The result of this product's diagnostic test(s). If any test fails, this will have the failed(2) value. Note, many products do not operate after a diagnostic f… |
| 1.3.6.1.4.1.49.2.1.5 | ScalarchipGenSerial | read-only | mandatory | The serial number of this product. |
| 1.3.6.1.4.1.49.2.1.6 | ScalarchipGenID | read-write | mandatory | A unique ID used for grouping disparate agents together. For example, a concentrator may contain multiple agents. This ID is could be assigned by the managemen… |
| 1.3.6.1.4.1.49.2.1.7 | ScalarchipGenVers | read-only | mandatory | The version identifier(s) for this agent. |
| 1.3.6.1.4.1.49.2.1.8 | ScalarchipGenAuthFailureAddr | read-only | mandatory | The source IP Address of the last SNMP request that caused an authentication failure trap to be generated. This object is also included in the SNMP authenticat… |
| 1.3.6.1.4.1.49.2.1.9 | ScalarchipGenTimeLastChanged | read-only | mandatory | A snapshot of sysUpTime when the last trap was generated. This attribute can be used to save polling by a management station. If there have been no traps gener… |
| 1.3.6.1.4.1.49.2.2 | NodechipEcho | |||
| 1.3.6.1.4.1.49.2.2.1 | ScalarchipEchoStart | read-write | mandatory | Setting chipEchoStart to startEcho(2) causes the device to begin an ICMP echo sequence using the parameters indicated by the rest of the chipEcho group. |
| 1.3.6.1.4.1.49.2.2.2 | ScalarchipEchoAddr | read-write | mandatory | The IP Address to which the device will ping. This object can only be set to valid unicast class A, class B, or class C addresses. The default IP Address is lo… |
| 1.3.6.1.4.1.49.2.2.3 | ScalarchipEchoPattern | read-write | mandatory | The actual pattern to be contained in the ICMP echo packet. |
| 1.3.6.1.4.1.49.2.2.4 | ScalarchipEchoNumber | read-write | mandatory | The number of ICMP echo packets (pings) to send. |
| 1.3.6.1.4.1.49.2.2.5 | ScalarchipEchoSize | read-write | mandatory | The size of the ICMP echo packet (ping) to send when chipEchoStart is set. The valid range is between 64 and 1500 octets. |
| 1.3.6.1.4.1.49.2.2.6 | ScalarchipEchoResponseCounts | read-only | mandatory | The count of ICMP echo response packets received since the last PING was initiated. |
| 1.3.6.1.4.1.49.2.3 | NodechipProducts | |||
| 1.3.6.1.4.1.49.2.3.1 | Nodeonline | |||
| 1.3.6.1.4.1.49.2.3.1.1 | NodeolAgents | |||
| 1.3.6.1.4.1.49.2.3.1.1.1 | ScalarolAgentsMySlot | read-only | mandatory | The slot id of this agent. |
| 1.3.6.1.4.1.49.2.3.1.1.2 | ScalarolAgentsMasterReset | read-write | mandatory | Resetting mastership causes a new mastership election to occur. The agent with the highest mastership priority will become the new master. If there is more tha… |
| 1.3.6.1.4.1.49.2.3.1.1.3 | TableolAgentsTable | not-accessible | mandatory | A table of agents in the concentrator as seen by this agent. A master will see all the agents; a slave will only see itself. |
| 1.3.6.1.4.1.49.2.3.1.1.3.1 | RowolAgentsEntry | not-accessible | mandatory | A profile of an agent within the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.1.3.1.1 | ColumnolAgentsSlotIndex | read-only | mandatory | The slot number that identifies the referenced agent. |
| 1.3.6.1.4.1.49.2.3.1.1.3.1.2 | ColumnolAgentsStationAddr | read-only | mandatory | The unique identifier for this agent. Often this is the value of ifPhysAddress for the first interface. |
| 1.3.6.1.4.1.49.2.3.1.1.3.1.3 | ColumnolAgentsIpAddress | read-only | mandatory | An IP Address that can be used to communicate to this agent. Note, this object's value may change as the agent switches to different sub-networks. |
| 1.3.6.1.4.1.49.2.3.1.1.3.1.4 | ColumnolAgentsMasterStatus | read-only | mandatory | The mastership status of this agent. |
| 1.3.6.1.4.1.49.2.3.1.1.3.1.5 | ColumnolAgentsMasterPriority | read-write | mandatory | The mastership priority of this agent. Ten is the highest and one is the lowest. Never means will not be able become master. Some agents do not have the capabi… |
| 1.3.6.1.4.1.49.2.3.1.1.3.1.6 | ColumnocAgentsSubSlot | read-only | mandatory | The subslot index for this agent. For agents not located in the ONcore system, this object will always return 1 for this object value. |
| 1.3.6.1.4.1.49.2.3.1.2 | NodeolConc | |||
| 1.3.6.1.4.1.49.2.3.1.2.1 | ScalarolConcType | read-only | mandatory | This object identifies the type of concentrator represented by this agent. |
| 1.3.6.1.4.1.49.2.3.1.2.2 | ScalarolConcReset | read-write | mandatory | Setting this value to reset(2) causes this concentrator to reset. |
| 1.3.6.1.4.1.49.2.3.1.2.3 | ScalarolConcNumSlots | read-only | mandatory | The number of slots in this concentrator. This value is the sum total of all payload slots plus any slots reserved for controller modules. For example, for an … |
| 1.3.6.1.4.1.49.2.3.1.2.4 | ScalarolConcProfile | read-only | mandatory | A bit string where the least significant bit corresponds to slot 1. A '1' in the bit indicates that a module is present in that slot. The number of octets prov… |
| 1.3.6.1.4.1.49.2.3.1.3 | NodeolEnv | |||
| 1.3.6.1.4.1.49.2.3.1.3.1 | ScalarolEnvTempStatus | read-only | mandatory | The overall temperature status for this concentrator. This object's value is an aggregate of all the temperature probes in the concentrator, such that, when at… |
| 1.3.6.1.4.1.49.2.3.1.3.2 | ScalarolEnvPSCapacity | read-only | mandatory | The total capacity of power supplies for this concentrator. |
| 1.3.6.1.4.1.49.2.3.1.3.3 | TableolEnvPSTable | not-accessible | mandatory | A table that contains information about each potential power supply in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.3.3.1 | RowolEnvPSEntry | not-accessible | mandatory | A list of information for each power supply in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.3.3.1.1 | ColumnolEnvPSIndex | read-only | mandatory | Identifies the power supply for which this entry contains power supply information. For systems with the primary and backup power supply (as opposed to the N+1… |
| 1.3.6.1.4.1.49.2.3.1.3.3.1.2 | ColumnolEnvPSAdminState | read-write | mandatory | The current desired state of the power supply. A power supply in standby does not provide power to the concentrator. Note, in a Load Sharing Hub, this object i… |
| 1.3.6.1.4.1.49.2.3.1.3.3.1.3 | ColumnolEnvPSOperStatus | read-only | mandatory | The current operational state of the power supply. A power supply in standby does not provide power to the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.3.4 | ScalarolEnvFanStatus | read-only | mandatory | The overall status of the fan(s). When fan operational status is known, this object's value is an aggregate of all fan status in the concentrator such that, wh… |
| 1.3.6.1.4.1.49.2.3.1.3.5 | TableolEnvTable | not-accessible | mandatory | A table that contains information about the concentrator environment. |
| 1.3.6.1.4.1.49.2.3.1.3.5.1 | RowolEnvEntry | not-accessible | mandatory | A list of information for each monitored component in this concentrator. |
| 1.3.6.1.4.1.49.2.3.1.3.5.1.1 | ColumnolEnvType | read-only | mandatory | The type of hardware component monitored in this concentrator. |
| 1.3.6.1.4.1.49.2.3.1.3.5.1.2 | ColumnolEnvStatus | read-only | mandatory | The status of the monitored hardware component. |
| 1.3.6.1.4.1.49.2.3.1.4 | NodeolModules | |||
| 1.3.6.1.4.1.49.2.3.1.4.1 | TableolModTable | not-accessible | mandatory | A table that contains generic information about every module that is present within the concentrator. If the concentrator is the ONcore Hub, then only the moth… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1 | RowolModEntry | not-accessible | mandatory | A list of information for each module in the concentrator. If the concentrator is the ONcore Hub, then only the motherboard is present in this table. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.1 | ColumnolModSlotIndex | read-only | mandatory | The unique slot number of this module. Its value ranges between 1 and olConcNumSlots and remains constant at least from one re-initialization of the entity's n… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.2 | ColumnolModType | read-only | mandatory | The unique type identifier for this module. This type is used to identify the branch in olSpecMods (see below). module-unmanageable(1) means that only the foll… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.3 | ColumnolModClass | read-only | mandatory | The class of this module. Generally speaking, this object indicates the kind of module. Specifically, the class identifier specifies the internal representatio… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.4 | ColumnolModDescr | read-only | mandatory | A textual string containing information about the module. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.5 | ColumnolModVersion | read-only | mandatory | The software version number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.6 | ColumnolModVendor | read-only | mandatory | The actual manufacturer of this board. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.7 | ColumnolModResetModule | read-write | mandatory | Setting this object to reset(2) causes this module to reset. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.8 | ColumnolModConfigToDips | read-write | mandatory | Setting this object to configure(2) causes this module to configure based on the dip switch settings. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.9 | ColumnolModConfigured | read-only | mandatory | This object indicates whether this module has already been configured. An unconfigured module is configured to a safe state where the network is isolated and t… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.10 | ColumnolModNetwork | read-write | mandatory | The network that this module is attached to. If the value is other(1) or port-switching(3), setting this object to a different value will generate the invalidD… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.11 | ColumnolModNetworkType | read-only | mandatory | The network type of this module. port-switching(3) means that the network type differs depending on the port (like the router module). The network type reflect… |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.12 | ColumnolModStatus | read-only | mandatory | The module's status. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.13 | ColumnolModNumPorts | read-only | mandatory | The number of ports on this module. Note, ports may be physical ports like 10BASE-T ports, or logical, like the bridge module ports. |
| 1.3.6.1.4.1.49.2.3.1.4.1.1.14 | ColumnolModNumTrunks | read-only | mandatory | The number of trunks on this module. Note, trunks are links that are, by definition, backbone connections. Examples of trunks are ring in and ring out ports fo… |
| 1.3.6.1.4.1.49.2.3.1.4.2 | TableolPortTable | not-accessible | mandatory | A table that contains generic information about each port on each module present within the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1 | RowolPortEntry | not-accessible | mandatory | A list of information about each port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.1 | ColumnolPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.2 | ColumnolPortIndex | read-only | mandatory | The port number of this port within this module. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.3 | ColumnolPortType | read-only | mandatory | The type of port. logical(1) is used to manage port resources that may not map directly to physical connections. The OEBM, for example, has two logical ports, … |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.4 | ColumnolPortConnector | read-only | mandatory | The connector type of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.5 | ColumnolPortStatus | read-only | mandatory | The status of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.6 | ColumnolPortAdminState | read-write | mandatory | The desired state of this port. Setting a port to be redundant-primary(3) or redundant-backup requires that the buddy slot and buddy port also be set to valid … |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.7 | ColumnolPortNetwork | read-write | mandatory | The network that this port is attached to. If the value of olPortNetwork is per-module(4), then use the olModNetwork to manage this port. Setting olPortNetwork… |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.8 | ColumnolPortNetworkType | read-only | mandatory | The network type of this port. The type reflects the valid values for olPortNetwork. |
| 1.3.6.1.4.1.49.2.3.1.4.2.1.9 | ColumnolPortAlertFilter | read-write | mandatory | Enabling this object for a port will allow the generation of port up (or port down) traps for port status transitions caused by end stations powering up (or do… |
| 1.3.6.1.4.1.49.2.3.1.4.3 | TableolTrunkTable | not-accessible | mandatory | A table that contains generic information about each trunk on each module present within the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1 | RowolTrunkEntry | not-accessible | mandatory | A list of information about each trunk in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.1 | ColumnolTrunkSlotIndex | read-only | mandatory | The slot number of this trunk's module. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.2 | ColumnolTrunkIndex | read-only | mandatory | The trunk number of this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.3 | ColumnolTrunkType | read-only | mandatory | The type of trunk. ringIn(3) and ringOut(4) refer to special trunks on the token ring protocol type modules. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.4 | ColumnolTrunkConnector | read-only | mandatory | The connector type of this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.5 | ColumnolTrunkStatus | read-only | mandatory | The status of this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.6 | ColumnolTrunkAdminState | read-write | mandatory | The desired state of this trunk. Enabling a trunk allows the trunk to pass network traffic. This object may be used to configure fiber trunk redundancy. Settin… |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.7 | ColumnolTrunkWrapState | read-only | mandatory | The wrap state of this trunk. A trunk can wrap in response to a network event such as a break in the cable. |
| 1.3.6.1.4.1.49.2.3.1.4.3.1.8 | ColumnolTrunkNeighbor | read-only | mandatory | The upstream or downstream neighbor of the trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4 | NodeolSpecMods | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.3 | Nodeol50nnMCTL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.3.1 | Tableol50nnMCTLModTable | not-accessible | mandatory | A table that contains information about each 50nnM-CTL in the concentrator. Note, current architecture will limit the number of instances to one per concentrat… |
| 1.3.6.1.4.1.49.2.3.1.4.4.3.1.1 | Rowol50nnMCTLModEntry | not-accessible | mandatory | A list of information for each 50nnM-CTL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.3.1.1.1 | Columnol50nnMCTLModSlotIndex | read-only | mandatory | The slot number for this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.3.1.1.2 | Columnol50nnMCTLModTempStatus | read-only | mandatory | The temperature as detected by the probes on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4 | Nodeol51nnMMGT | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.4.1 | Tableol51nnMMGTModTable | not-accessible | mandatory | A table that contains module information about each EMM module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.1.1 | Rowol51nnMMGTModEntry | not-accessible | mandatory | A list of module information for a particular EMM module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.1 | Columnol51nnMMGTModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.2 | Columnol51nnMMGTModMasterPriority | read-write | mandatory | The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive un… |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.3 | Columnol51nnMMGTModMasterStatus | read-only | mandatory | The mastership status of this agent. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.4 | Columnol51nnMMGTModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. Note that EMMs before v3.0 will have 00-00-00-00-00-0… |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.2 | Tableol51nnMMGTPortTable | not-accessible | mandatory | A table of information that contains port-specific information for each port on each 51nnM-MGT module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.2.1 | Rowol51nnMMGTPortEntry | not-accessible | mandatory | A list of information about a specific port on a 51nnM-MGT module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.2.1.1 | Columnol51nnMMGTPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.2.1.2 | Columnol51nnMMGTPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.4.2.1.3 | Columnol51nnMMGTIpAddress | read-only | mandatory | The IP Address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5 | Nodeol51nnMFIB | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.5.1 | Tableol51nnMFIBModTable | not-accessible | mandatory | A table of module-specific information for each 51nnM-FIB module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.1.1 | Rowol51nnMFIBModEntry | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-FIB module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.1 | Columnol51nnMFIBModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.2 | Columnol51nnMFIBModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.3 | Columnol51nnMFIBModLLW | read-write | mandatory | The current state of this module's low light warning configuration. Enabling this feature causes the module to check for low light and to issue a warning if lo… |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.4 | Columnol51nnMFIBModDipLLW | read-only | mandatory | The low light warning configuration indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2 | Tableol51nnMFIBPortTable | not-accessible | mandatory | A table of port-specific information for each port of each 51nnM-FIB module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1 | Rowol51nnMFIBPortEntry | not-accessible | mandatory | A list of information about a specific port on a 51nnM-FIB module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.1 | Columnol51nnMFIBPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.2 | Columnol51nnMFIBPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.3 | Columnol51nnMFIBPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.4 | Columnol51nnMFIBPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.5 | Columnol51nnMFIBPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.6 | Columnol51nnMFIBPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6 | Nodeol51nnMUTP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1 | Tableol51nnMUTPModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-UTP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1 | Rowol51nnMUTPModEntry | not-accessible | mandatory | A module entry containing objects that describe the module level for that particular module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.1 | Columnol51nnMUTPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.2 | Columnol51nnMUTPModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.3 | Columnol51nnMUTPModCrossover | read-write | mandatory | The current state of this module's crossover configuration. Setting this object to uncrossed(2) allows the last port to be used to connect to another repeater.… |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.4 | Columnol51nnMUTPModDipCrossover | read-only | mandatory | The crossover configuration indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.5 | Columnol51nnMUTPModFFL | read-write | mandatory | The number of bits to store in the repeater's fifo buffer. See the module user's guide for more information. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.6 | Columnol51nnMUTPModDipFFL | read-write | mandatory | The fifo fill level as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2 | Tableol51nnMUTPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1 | Rowol51nnMUTPPortEntry | not-accessible | mandatory | A port entry containing objects that describe this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.1 | Columnol51nnMUTPPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.2 | Columnol51nnMUTPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.3 | Columnol51nnMUTPPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.4 | Columnol51nnMUTPPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.5 | Columnol51nnMUTPPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.6 | Columnol51nnMUTPPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.7 | Columnol51nnMUTPPortLinkInteg | read-write | mandatory | The port's link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.8 | Columnol51nnMUTPPortDipLinkInteg | read-only | mandatory | The link integrity configuration as indicated by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.9 | Columnol51nnMUTPPortSquelch | read-write | mandatory | The port's squelch configuration. See the module's user's guide for more information. |
| 1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.10 | Columnol51nnMUTPPortDipSquelch | read-only | mandatory | The port's squelch configuration as indicated by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7 | Nodeol51nnMTP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.7.1 | Tableol51nnMTPModTable | not-accessible | mandatory | A table of module-specific information for each 51nnM-TP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.1.1 | Rowol51nnMTPModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.1 | Columnol51nnMTPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.2 | Columnol51nnMTPModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.3 | Columnol51nnMTPModCrossover | read-write | mandatory | The current state of this module's crossover configuration. Setting this object to uncrossed(2) allows the last port to be used to connect to another repeater.… |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.4 | Columnol51nnMTPModDipCrossover | read-only | mandatory | The crossover configuration indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2 | Tableol51nnMTPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1 | Rowol51nnMTPPortEntry | not-accessible | mandatory | A port entry containing objects that describe this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.1 | Columnol51nnMTPPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.2 | Columnol51nnMTPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.3 | Columnol51nnMTPPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.4 | Columnol51nnMTPPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.5 | Columnol51nnMTPPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.6 | Columnol51nnMTPPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.7 | Columnol51nnMTPPortLinkInteg | read-write | mandatory | The port's link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.8 | Columnol51nnMTPPortDipLinkInteg | read-only | mandatory | The link integrity configuration as indicated by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.9 | Columnol51nnMTPPortSquelch | read-write | mandatory | The port's squelch configuration. See the module's user's guide for more information. |
| 1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.10 | Columnol51nnMTPPortDipSquelch | read-only | mandatory | The port's squelch configuration as indicated by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8 | Nodeol51nnMBNC | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.8.1 | Tableol51nnMBNCModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-BNC module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.1.1 | Rowol51nnMBNCModEntry | not-accessible | mandatory | A module entry containing objects that describe the module level for that particular module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.1.1.1 | Columnol51nnMBNCModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.1.1.2 | Columnol51nnMBNCModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2 | Tableol51nnMBNCPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2.1 | Rowol51nnMBNCPortEntry | not-accessible | mandatory | A port entry containing objects that describe this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.1 | Columnol51nnMBNCPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.2 | Columnol51nnMBNCPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.3 | Columnol51nnMBNCPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.4 | Columnol51nnMBNCPortDipTermination | read-only | mandatory | The state of this port's termination as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.5 | Columnol51nnMBNCPortDipGround | read-only | mandatory | The state of this port's ground as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9 | Nodeol51nnBEE | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.9.1 | Tableol51nnBEEModTable | not-accessible | mandatory | A table of module-specific information for each 51nnB-EE module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.1.1 | Rowol51nnBEEModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnB-EE module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.1.1.1 | Columnol51nnBEEModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.1.1.2 | Columnol51nnBEEModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.1.1.3 | Columnol51nnBEEModProtocols | read-only | mandatory | A textual description of the protocols supported by this module |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2 | Tableol51nnBEEPortTable | not-accessible | mandatory | A table of port-specific for each port of each 51nnB-EE module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2.1 | Rowol51nnBEEPortEntry | not-accessible | mandatory | A list of port-specific informatoin about a specific 51nnB-EE port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.1 | Columnol51nnBEEPortSlotIndex | read-only | mandatory | The slot number for this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.2 | Columnol51nnBEEPortIndex | read-only | mandatory | The port number for this port within this slot. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.3 | Columnol51nnBEEPortIpAddress | read-only | mandatory | The IP Address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.4 | Columnol51nnBEEPortDipNetwork | read-only | mandatory | The network for this port as specified by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.5 | Columnol51nnBEEPortDefNetwork | read-only | mandatory | The network for this port as specified by the OEBM's non-volatile storage. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10 | Nodeol51nnRES | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.10.1 | Tableol51nnRESModTable | not-accessible | mandatory | A table of module-specific information for each 51nnR-ES module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.1.1 | Rowol51nnRESModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnR-ES module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.1.1.1 | Columnol51nnRESModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.1.1.2 | Columnol51nnRESModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.1.1.3 | Columnol51nnRESModProtocols | read-only | mandatory | A textual description of the protocols supported by this module |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2 | Tableol51nnRESPortTable | not-accessible | mandatory | A table of port-specific for each port of each 51nnR-ES module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2.1 | Rowol51nnRESPortEntry | not-accessible | mandatory | A list of port-specific informatoin about a specific 51nnR-ES port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.1 | Columnol51nnRESPortSlotIndex | read-only | mandatory | The slot number for this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.2 | Columnol51nnRESPortIndex | read-only | mandatory | The port number for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.3 | Columnol51nnRESPortIpAddress | read-only | mandatory | The IP Address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.4 | Columnol51nnRESPortDipNetwork | read-only | mandatory | The network for this port as specified by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.5 | Columnol51nnRESPortDefNetwork | read-only | mandatory | The network for this port as specified by the OERM's non-volatile storage. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11 | Nodeol51nnREE | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.11.1 | Tableol51nnREEModTable | not-accessible | mandatory | A table of module-specific information for each 51nnR-EE module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.1.1 | Rowol51nnREEModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnR-EE module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.1.1.1 | Columnol51nnREEModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.1.1.2 | Columnol51nnREEModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.1.1.3 | Columnol51nnREEModProtocols | read-only | mandatory | A textual description of the protocols supported by this module |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2 | Tableol51nnREEPortTable | not-accessible | mandatory | A table of port-specific for each port of each 51nnR-EE module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2.1 | Rowol51nnREEPortEntry | not-accessible | mandatory | A list of port-specific informatoin about a specific 51nnR-EE port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.1 | Columnol51nnREEPortSlotIndex | read-only | mandatory | The slot number for this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.2 | Columnol51nnREEPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.3 | Columnol51nnREEPortIpAddress | read-only | mandatory | The IP Address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.4 | Columnol51nnREEPortDipNetwork | read-only | mandatory | The network for this port as specified by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.5 | Columnol51nnREEPortDefNetwork | read-only | mandatory | The network for this port as specified by the OERM's non-volatile storage. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12 | Nodeol51nnMAUIF | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.12.1 | Tableol51nnMAUIFModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-AUIF module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.1.1 | Rowol51nnMAUIFModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-AUIF module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.1.1.1 | Columnol51nnMAUIFModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2 | Tableol51nnMAUIFPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1 | Rowol51nnMAUIFPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-AUIF port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.1 | Columnol51nnMAUIFPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.2 | Columnol51nnMAUIFPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.3 | Columnol51nnMAUIFPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.4 | Columnol51nnMAUIFPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.5 | Columnol51nnMAUIFPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.6 | Columnol51nnMAUIFPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.7 | Columnol51nnMAUIFPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13 | Nodeol51nnMAUIM | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.13.1 | Tableol51nnMAUIMModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-AUIM module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.1.1 | Rowol51nnMAUIMModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-AUIM module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.1.1.1 | Columnol51nnMAUIMModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2 | Tableol51nnMAUIMPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1 | Rowol51nnMAUIMPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-AUIM port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.1 | Columnol51nnMAUIMPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.2 | Columnol51nnMAUIMPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.3 | Columnol51nnMAUIMPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.4 | Columnol51nnMAUIMPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.5 | Columnol51nnMAUIMPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.6 | Columnol51nnMAUIMPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.7 | Columnol51nnMAUIMPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.8 | Columnol51nnMAUIMPortSQETest | read-write | mandatory | The current SQE test configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.9 | Columnol51nnMAUIMPortDipSQETest | read-only | mandatory | The SQE test configuration for this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.10 | Columnol51nnMAUIMPortCollision | read-write | mandatory | The current collision configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.11 | Columnol51nnMAUIMPortDipCollision | read-only | mandatory | The collision configuration for this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.12 | Columnol51nnMAUIMPortHalfStep | read-write | mandatory | The current step configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.13 | Columnol51nnMAUIMPortDipHalfStep | read-only | mandatory | The step configuration for this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14 | Nodeol5208MTP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.14.1 | Tableol5208MTPModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 5208M-TP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.1.1 | Rowol5208MTPModEntry | not-accessible | mandatory | A description of the 5208M-TP module attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.1 | Columnol5208MTPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.2 | Columnol5208MTPModBypsAdminState | read-write | mandatory | The desired state of this module with respect to the ring. Setting this attribute to bypass(2) will cause this module to be removed from the ring that passes t… |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.3 | Columnol5208MTPModBypsOperState | read-only | mandatory | The operational state of this module with respect to the ring. If this attribute is equal to bypass(2), then the module has been removed from the ring that pas… |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.4 | Columnol5208MTPModDipCableImp | read-only | mandatory | The setting of this module's port impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twist… |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.2 | Tableol5208MTPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.2.1 | Rowol5208MTPPortEntry | not-accessible | mandatory | A description of 5208M-TP port attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.1 | Columnol5208MTPPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.2 | Columnol5208MTPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.3 | Columnol5208MTPPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.4 | Columnol5208MTPPortStationType | read-write | mandatory | Determines whether the station connected to this port has a MAC address. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3 | Tableol5208MTPTrunkTable | not-accessible | mandatory | A list of trunk-specific information about each trunk for this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1 | Rowol5208MTPTrunkEntry | not-accessible | mandatory | A description of 5208M-TP trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.1 | Columnol5208MTPTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.2 | Columnol5208MTPTrunkIndex | read-only | mandatory | The trunk number for this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.3 | Columnol5208MTPTrunkDipAdminState | read-only | mandatory | The state of this trunk as indicated by the trunk's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.4 | Columnol5208MTPTrunkCableMon | read-write | mandatory | The cable monitor configuration for this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.5 | Columnol5208MTPTrunkDipCableMon | read-only | mandatory | The cable monitor configuration as indicated by this trunk's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.6 | Columnol5208MTPTrunkNetMapState | read-write | mandatory | The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate… |
| 1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.7 | Columnol5208MTPTrunkExtBcnRecovery | read-write | mandatory | Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which… |
| 1.3.6.1.4.1.49.2.3.1.4.4.15 | Nodeol51nnMFP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.15.1 | Tableol51nnMFPModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-FP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.1.1 | Rowol51nnMFPModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-FP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.1.1.1 | Columnol51nnMFPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2 | Tableol51nnMFPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1 | Rowol51nnMFPPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-FP port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.1 | Columnol51nnMFPPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.2 | Columnol51nnMFPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.3 | Columnol51nnMFPPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.4 | Columnol51nnMFPPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.5 | Columnol51nnMFPPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.6 | Columnol51nnMFPPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.7 | Columnol51nnMFPPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.8 | Columnol51nnMFPPortLLW | read-write | mandatory | The current low light warning configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.9 | Columnol51nnMFPPortDipLLW | read-only | mandatory | The low light warning configuration indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.10 | Columnol51nnMFPPortHipwr | read-write | mandatory | The current high power optic configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.11 | Columnol51nnMFPPortDipHipwr | read-only | mandatory | The high power optic configuration for this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16 | Nodeol51nnMFBP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.16.1 | Tableol51nnMFBPModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-FBP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.1.1 | Rowol51nnMFBPModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-FBP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.1.1.1 | Columnol51nnMFBPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2 | Tableol51nnMFBPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1 | Rowol51nnMFBPPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-FBP port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.1 | Columnol51nnMFBPPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.2 | Columnol51nnMFBPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.3 | Columnol51nnMFBPPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.4 | Columnol51nnMFBPPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.5 | Columnol51nnMFBPPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.6 | Columnol51nnMFBPPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.7 | Columnol51nnMFBPPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.8 | Columnol51nnMFBPPortLLW | read-write | mandatory | The current low light warning configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.9 | Columnol51nnMFBPPortDipLLW | read-only | mandatory | The low light warning configuration indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.10 | Columnol51nnMFBPPortHipwr | read-write | mandatory | The current high power optic configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.11 | Columnol51nnMFBPPortDipHipwr | read-only | mandatory | The high power optic configuration for this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17 | Nodeol51nnMTPL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.17.1 | Tableol51nnMTPLModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-TPL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.1.1 | Rowol51nnMTPLModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.1.1.1 | Columnol51nnMTPLModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.1.1.2 | Columnol51nnMTPLModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2 | Tableol51nnMTPLPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1 | Rowol51nnMTPLPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPL port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.1 | Columnol51nnMTPLPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.2 | Columnol51nnMTPLPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.3 | Columnol51nnMTPLPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the … |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.4 | Columnol51nnMTPLPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.5 | Columnol51nnMTPLPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.6 | Columnol51nnMTPLPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.7 | Columnol51nnMTPLPortLinkInteg | read-write | mandatory | The current link integrity configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.8 | Columnol51nnMTPLPortDipLinkInteg | read-only | mandatory | The link integrity configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.9 | Columnol51nnMTPLPortSquelch | read-write | mandatory | The current squelch configuration for this port. See the module's user's guide for more information. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.10 | Columnol51nnMTPLPortJabber | read-write | mandatory | The current receive jabber configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.11 | Columnol51nnMTPLPortDipJabber | read-only | mandatory | The receive jabber configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18 | Nodeol51nnMTPPL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.18.1 | Tableol51nnMTPPLModTable | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPPL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.1.1 | Rowol51nnMTPPLModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPPL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.1.1.1 | Columnol51nnMTPPLModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2 | Tableol51nnMTPPLPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1 | Rowol51nnMTPPLPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPPL port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.1 | Columnol51nnMTPPLPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.2 | Columnol51nnMTPPLPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.3 | Columnol51nnMTPPLPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the … |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.4 | Columnol51nnMTPPLPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.5 | Columnol51nnMTPPLPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.6 | Columnol51nnMTPPLPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.7 | Columnol51nnMTPPLPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.8 | Columnol51nnMTPPLPortLinkInteg | read-write | mandatory | The current link integrity configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.9 | Columnol51nnMTPPLPortDipLinkInteg | read-only | mandatory | The link integrity configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.10 | Columnol51nnMTPPLPortSquelch | read-write | mandatory | The current squelch configuration for this port. See the module's user's guide for more information. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.11 | Columnol51nnMTPPLPortJabber | read-write | mandatory | The current receive jabber configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.12 | Columnol51nnMTPPLPortDipJabber | read-only | mandatory | The receive jabber configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19 | Nodeol52nnMTP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1 | Tableol52nnMTPModTable | not-accessible | mandatory | A list of module-specific information about a specific 52nnM-TP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1.1 | Rowol52nnMTPModEntry | not-accessible | mandatory | A description of the 52nnM-TP module attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.1 | Columnol52nnMTPModSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.2 | Columnol52nnMTPModRingSpeed | read-write | mandatory | The ring's bandwidth. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.3 | Columnol52nnMTPModDipRingSpeed | read-only | mandatory | The dip switch setting for the ring's bandwidth. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.4 | Columnol52nnMTPModCableImp | read-write | mandatory | The setting of this module's port impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twist… |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.5 | Columnol52nnMTPModDipCableImp | read-only | mandatory | The dip switch setting for the module's port impedance matching. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.2 | Tableol52nnMTPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.2.1 | Rowol52nnMTPPortEntry | not-accessible | mandatory | A description of 52nnM-TP port attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.1 | Columnol52nnMTPPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.2 | Columnol52nnMTPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.3 | Columnol52nnMTPPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.4 | Columnol52nnMTPPortStationType | read-write | mandatory | Determines whether the station connected to this port has a MAC address. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.3 | Tableol52nnMTPTrunkTable | not-accessible | mandatory | A list of trunk-specific information about each trunk for this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.3.1 | Rowol52nnMTPTrunkEntry | not-accessible | mandatory | A description of 52nnM-TP trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.3.1.1 | Columnol52nnMTPTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.3.1.2 | Columnol52nnMTPTrunkIndex | read-only | mandatory | The trunk number for this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.19.3.1.3 | Columnol52nnMTPTrunkDipAdminState | read-only | mandatory | The state of this trunk as indicated by the trunk's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20 | Nodeol52nnMFR | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.20.1 | Tableol52nnMFRModTable | not-accessible | mandatory | A list of module-specific information about a specific 52nnM-FR module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.1.1 | Rowol52nnMFRModEntry | not-accessible | mandatory | A description of the 52nnM-FR module attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.1.1.1 | Columnol52nnMFRModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.1.1.2 | Columnol52nnMFRModRingSpeed | read-write | mandatory | The ring's bandwidth. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.1.1.3 | Columnol52nnMFRModDipRingSpeed | read-only | mandatory | The dip switch setting for the ring's bandwidth. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2 | Tableol52nnMFRPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2.1 | Rowol52nnMFRPortEntry | not-accessible | mandatory | A description of 52nnM-FR port attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.1 | Columnol52nnMFRPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.2 | Columnol52nnMFRPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.3 | Columnol52nnMFRPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.4 | Columnol52nnMFRPortCableImp | read-only | mandatory | The setting of this port's impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair… |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.5 | Columnol52nnMFRPortStationType | read-write | mandatory | Determines whether the station connected to this port has a MAC address. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3 | Tableol52nnMFRTrunkTable | not-accessible | mandatory | A list of trunk-specific information about each trunk for this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1 | Rowol52nnMFRTrunkEntry | not-accessible | mandatory | A description of 52nnM-FR trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.1 | Columnol52nnMFRTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.2 | Columnol52nnMFRTrunkIndex | read-only | mandatory | The trunk number of this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.3 | Columnol52nnMFRTrunkDipAdminState | read-only | mandatory | The state of this trunk as indicated by the trunk's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.4 | Columnol52nnMFRTrunkCableMon | read-write | mandatory | The cable monitor configuration for this trunk. This does not apply to fiber trunks. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.5 | Columnol52nnMFRTrunkDipCableMon | read-only | mandatory | The cable monitor configuration as indicated by this trunk's dip switches. This does not apply to fiber trunks. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.6 | Columnol52nnMFRTrunkCompMode | read-write | mandatory | The compatibility mode for this trunk. This only applies to fiber trunks. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.7 | Columnol52nnMFRTrunkDipCompMode | read-only | mandatory | The compatibility mode as indicated by this trunk's dip switches. This only applies to fiber trunks. |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.8 | Columnol52nnMFRTrunkNetMapState | read-write | mandatory | The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate… |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.9 | Columnol52nnMFRTrunkExtBcnRecovery | read-write | mandatory | Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which… |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.10 | Columnol52nnMFRTrunkBuddySlot | read-write | mandatory | The slot index of the redundant trunk's buddy. To set a trunk to be redundant, the buddy's slot must be set to a valid value. This object is applicable to fibe… |
| 1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.11 | Columnol52nnMFRTrunkAdminState | read-write | mandatory | The desired state of this trunk. Enabling a trunk allows the trunk to pass network traffic. This object may be used to configure fiber trunk redundancy. Settin… |
| 1.3.6.1.4.1.49.2.3.1.4.4.21 | Nodeol51nnMTS | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1 | Tableol51nnMTSModTable | not-accessible | mandatory | A table of module-specific information for each 51nnM-TS module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1 | Rowol51nnMTSModEntry | not-accessible | mandatory | A list of module information for each 51nnM-TS module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.1 | Columnol51nnMTSModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.2 | Columnol51nnMTSModProtocols | read-only | mandatory | A textual description of the protocols supported by this module |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.3 | Columnol51nnMTSModIpAddress | read-only | mandatory | The IP Address of the terminal server. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.4 | Columnol51nnMTSModTCPPort | read-only | mandatory | The TCP port number of the the terminal server's remote console port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.5 | Columnol51nnMTSModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the mac address of the terminal server. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.6 | Columnol51nnMTSModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.7 | Columnol51nnMTSModCPURev | read-only | mandatory | The terminal server's CPU revision. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.2 | Tableol51nnMTSPortTable | not-accessible | mandatory | A table of information that contains port-specific information for each port on each 51nnM-TS module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.2.1 | Rowol51nnMTSPortEntry | not-accessible | mandatory | A list of information about a specific port on a 51nnM-TS module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.1 | Columnol51nnMTSPortSlotIndex | read-only | mandatory | The slot number for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.2 | Columnol51nnMTSPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.3 | Columnol51nnMTSPortAdminState | read-write | mandatory | The administrative state of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.4 | Columnol51nnMTSPortOperState | read-only | mandatory | The operational mode of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22 | Nodeol51nnMFL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.22.1 | Tableol51nnMFLModTable | not-accessible | mandatory | A table of module-specific information for each 51nnM-FL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.1.1 | Rowol51nnMFLModEntry | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-FL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.1.1.1 | Columnol51nnMFLModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.1.1.2 | Columnol51nnMFLModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2 | Tableol51nnMFLPortTable | not-accessible | mandatory | A table of port-specific information for each port of each 51nnM-FL module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1 | Rowol51nnMFLPortEntry | not-accessible | mandatory | A list of information about a specific port on a 51nnM-FL module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.1 | Columnol51nnMFLPortSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.2 | Columnol51nnMFLPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.3 | Columnol51nnMFLPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return invalidData error. Remote Fail… |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.4 | Columnol51nnMFLPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.5 | Columnol51nnMFLPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. |
| 1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.6 | Columnol51nnMFLPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.23 | Nodeol50nnMRCTL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.23.1 | Tableol50nnMRCTLModTable | not-accessible | mandatory | A table that contains information about each 50nnM-RCTL in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.23.1.1 | Rowol50nnMRCTLModEntry | not-accessible | mandatory | A list of information for each 50nnM-RCTL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.1 | Columnol50nnMRCTLModSlotIndex | read-only | mandatory | The slot number for this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.2 | Columnol50nnMRCTLModOperState | read-only | mandatory | The operational state of the 50nnM-RCTL module. Specifically, this is an indicator of whether the 50nnM-RCTL module is providing clock signals to the backplane… |
| 1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.3 | Columnol50nnMRCTLModClockStatus | read-only | mandatory | The current status of the on-board clocks on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.4 | Columnol50nnMRCTLModTempStatus | read-only | mandatory | The temperature as detected by the probe on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24 | Nodeol51nnMFB | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.24.1 | Tableol51nnMFBModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 51nnM-FB module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.1.1 | Rowol51nnMFBModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-FB module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.1 | Columnol51nnMFBModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.2 | Columnol51nnMFBModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.3 | Columnol51nnMFBModLLW | read-write | mandatory | The current state of this module's low light warning configuration. Enabling this feature causes the module to check for low light and to issue a warning if lo… |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.4 | Columnol51nnMFBModDipLLW | read-only | mandatory | The low light warning configuration indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2 | Tableol51nnMFBPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1 | Rowol51nnMFBPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-FB port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.1 | Columnol51nnMFBPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.2 | Columnol51nnMFBPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.3 | Columnol51nnMFBPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.4 | Columnol51nnMFBPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.5 | Columnol51nnMFBPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.6 | Columnol51nnMFBPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25 | Nodeol53nnMMGT | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1 | Tableol53nnMMGTModTable | not-accessible | mandatory | A list of module attributes that apply to this model. To access an ol53nnMMGTModTable entry, the ol53nnMMGTModSlotIndex attribute is used. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1 | Rowol53nnMMGTModEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-MGT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.1 | Columnol53nnMMGTModSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.2 | Columnol53nnMMGTModMasterPriority | read-write | mandatory | The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive un… |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.3 | Columnol53nnMMGTModMasterStatus | read-only | mandatory | The mastership status of this agent. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.4 | Columnol53nnMMGTModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the MAC address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.5 | Columnol53nnMMGTModIpAddress | read-only | mandatory | The IP address associated with this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.6 | Columnol53nnMMGTModDownStreamMAC | read-only | mandatory | Down stream MAC |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.7 | Columnol53nnMMGTModUpStreamMAC | read-only | mandatory | Up stream MAC |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.8 | Columnol53nnMMGTModfddiMACPath | read-write | mandatory | The FDDI path which should be inserted into the MAC |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.9 | Columnol53nnMMGTModDownStreamModule | read-only | mandatory | Down stream slot (transmit to) |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.10 | Columnol53nnMMGTModUpStreamModule | read-only | mandatory | Up stream slot (receive from) |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.11 | Columnol53nnMMGTModDownStreamOperPath | read-only | mandatory | Transmit DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.12 | Columnol53nnMMGTModUpStreamOperPath | read-only | mandatory | Receive DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.13 | Columnol53nnMMGTModRingInfo | read-only | mandatory | An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2 | Tableol53nnMMGTPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1 | Rowol53nnMMGTPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-MGT port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.1 | Columnol53nnMMGTPortSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.2 | Columnol53nnMMGTPortIndex | read-only | mandatory | A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular valu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.3 | Columnol53nnMMGTPortConfig | read-only | mandatory | Specifies the FDDI port type (a or b). |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.4 | Columnol53nnMMGTPortPcmState | read-only | mandatory | (refer to ANSI SMT 9.6.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.5 | Columnol53nnMMGTPortConnectState | read-only | mandatory | An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Wit… |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.6 | Columnol53nnMMGTPortNeighbor | read-only | mandatory | The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.7 | Columnol53nnMMGTPortRemoteMACIndicated | read-only | mandatory | The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT … |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.8 | Columnol53nnMMGTPortBSFlag | read-only | mandatory | The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.9 | Columnol53nnMMGTPortPCWithhold | read-only | mandatory | PC-Withhold, (refer to ANSI SMT 9.4.1). |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.10 | Columnol53nnMMGTPortLerCondition | read-only | mandatory | This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.3 | Tableol53nnMMGTTrunkTable | not-accessible | mandatory | FDDI module specific trunk table variables. At present there are none. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.3.1 | Rowol53nnMMGTTrunkEntry | not-accessible | mandatory | A description of 53nnM-MGT trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.3.1.1 | Columnol53nnMMGTTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.25.3.1.2 | Columnol53nnMMGTTrunkIndex | read-only | mandatory | A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular va… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26 | Nodeol53nnMFBMIC | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1 | Tableol53nnMFBMICModTable | not-accessible | mandatory | A list of module attributes that apply to this model. To access an ol53nnMFBMICModTable entry, the ol53nnMFBMICModSlotIndex attribute is used. |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1 | Rowol53nnMFBMICModEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-FBMIC module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.1 | Columnol53nnMFBMICModSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.2 | Columnol53nnMFBMICModDownStreamModule | read-only | mandatory | Down stream slot (transmit to) |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.3 | Columnol53nnMFBMICModUpStreamModule | read-only | mandatory | Up stream slot (receive from) |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.4 | Columnol53nnMFBMICModDownStreamOperPath | read-only | mandatory | Transmit DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.5 | Columnol53nnMFBMICModUpStreamOperPath | read-only | mandatory | Receive DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.6 | Columnol53nnMFBMICModRingInfo | read-only | mandatory | An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2 | Tableol53nnMFBMICPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1 | Rowol53nnMFBMICPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-FBMIC port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.1 | Columnol53nnMFBMICPortSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.2 | Columnol53nnMFBMICPortIndex | read-only | mandatory | A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular valu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.3 | Columnol53nnMFBMICPortConfig | read-write | mandatory | Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3), and master(4). In addition, there can only be one active slave po… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.4 | Columnol53nnMFBMICPortPcmState | read-only | mandatory | (refer to ANSI SMT 9.6.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.5 | Columnol53nnMFBMICPortConnectState | read-only | mandatory | An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Wit… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.6 | Columnol53nnMFBMICPortNeighbor | read-only | mandatory | The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.7 | Columnol53nnMFBMICPortRemoteMACIndicated | read-only | mandatory | The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT … |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.8 | Columnol53nnMFBMICPortBSFlag | read-only | mandatory | The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.9 | Columnol53nnMFBMICPortPCWithhold | read-only | mandatory | PC-Withhold, (refer to ANSI SMT 9.4.1). |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.10 | Columnol53nnMFBMICPortLerCondition | read-only | mandatory | This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.3 | Tableol53nnMFBMICTrunkTable | not-accessible | mandatory | FDDI module specific trunk table variables. At present there are none. |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.3.1 | Rowol53nnMFBMICTrunkEntry | not-accessible | mandatory | A description of 53nnM-FBMIC trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.3.1.1 | Columnol53nnMFBMICTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.26.3.1.2 | Columnol53nnMFBMICTrunkIndex | read-only | mandatory | A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular va… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27 | Nodeol53nnMFIBST | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1 | Tableol53nnMFIBSTModTable | not-accessible | mandatory | A list of module attributes that apply to this model. To access an ol53nnMFIBSTModTable entry, the ol53nnMFIBSTModSlotIndex attribute is used. |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1 | Rowol53nnMFIBSTModEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-FIBST module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.1 | Columnol53nnMFIBSTModSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.2 | Columnol53nnMFIBSTModDownStreamModule | read-only | mandatory | Down stream slot (transmit to) |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.3 | Columnol53nnMFIBSTModUpStreamModule | read-only | mandatory | Up stream slot (receive from) |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.4 | Columnol53nnMFIBSTModDownStreamOperPath | read-only | mandatory | Transmit DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.5 | Columnol53nnMFIBSTModUpStreamOperPath | read-only | mandatory | Receive DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.6 | Columnol53nnMFIBSTModRingInfo | read-only | mandatory | An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2 | Tableol53nnMFIBSTPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1 | Rowol53nnMFIBSTPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-FIBST port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.1 | Columnol53nnMFIBSTPortSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.2 | Columnol53nnMFIBSTPortIndex | read-only | mandatory | A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular valu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.3 | Columnol53nnMFIBSTPortConfig | read-write | mandatory | Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave por… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.4 | Columnol53nnMFIBSTPortPcmState | read-only | mandatory | (refer to ANSI SMT 9.6.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.5 | Columnol53nnMFIBSTPortConnectState | read-only | mandatory | An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Wit… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.6 | Columnol53nnMFIBSTPortNeighbor | read-only | mandatory | The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.7 | Columnol53nnMFIBSTPortRemoteMACIndicated | read-only | mandatory | The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT … |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.8 | Columnol53nnMFIBSTPortBSFlag | read-only | mandatory | The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.9 | Columnol53nnMFIBSTPortPCWithhold | read-only | mandatory | PC-Withhold, (refer to ANSI SMT 9.4.1). |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.10 | Columnol53nnMFIBSTPortLerCondition | read-only | mandatory | This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.3 | Tableol53nnMFIBSTTrunkTable | not-accessible | mandatory | FDDI module specific trunk table variables. At present there are none. |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.3.1 | Rowol53nnMFIBSTTrunkEntry | not-accessible | mandatory | A description of 53nnM-FIBST trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.3.1.1 | Columnol53nnMFIBSTTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.27.3.1.2 | Columnol53nnMFIBSTTrunkIndex | read-only | mandatory | A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular va… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28 | Nodeol53nnMSTP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1 | Tableol53nnMSTPModTable | not-accessible | mandatory | A list of module attributes that apply to this model. To access an ol53nnMSTPModTable entry, the ol53nnMSTPModSlotIndex attribute is used. |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1 | Rowol53nnMSTPModEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-STP module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.1 | Columnol53nnMSTPModSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.2 | Columnol53nnMSTPModDownStreamModule | read-only | mandatory | Down stream slot (transmit to) |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.3 | Columnol53nnMSTPModUpStreamModule | read-only | mandatory | Down stream slot (receive from) |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.4 | Columnol53nnMSTPModDownStreamOperPath | read-only | mandatory | transmit DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.5 | Columnol53nnMSTPModUpStreamOperPath | read-only | mandatory | receive DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.6 | Columnol53nnMSTPModRingInfo | read-only | mandatory | An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2 | Tableol53nnMSTPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1 | Rowol53nnMSTPPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-STP port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.1 | Columnol53nnMSTPPortSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.2 | Columnol53nnMSTPPortIndex | read-only | mandatory | A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular valu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.3 | Columnol53nnMSTPPortConfig | read-write | mandatory | Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave por… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.4 | Columnol53nnMSTPPortPcmState | read-only | mandatory | (refer to ANSI SMT 9.6.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.5 | Columnol53nnMSTPPortConnectState | read-only | mandatory | An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Wit… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.6 | Columnol53nnMSTPPortNeighbor | read-only | mandatory | The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.7 | Columnol53nnMSTPPortRemoteMACIndicated | read-only | mandatory | The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT … |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.8 | Columnol53nnMSTPPortBSFlag | read-only | mandatory | The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.9 | Columnol53nnMSTPPortPCWithhold | read-only | mandatory | PC-Withhold, (refer to ANSI SMT 9.4.1). |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.10 | Columnol53nnMSTPPortLerCondition | read-only | mandatory | This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.11 | Columnol53nnMSTPPortPersonality | read-write | mandatory | Specifies the physical signaling used by the port, the only valid values are sddi(3) and tpddi(4). |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.3 | Tableol53nnMSTPTrunkTable | not-accessible | mandatory | FDDI module specific trunk table variables. At present there are none. |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.3.1 | Rowol53nnMSTPTrunkEntry | not-accessible | mandatory | A description of 53nnM-STP trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.3.1.1 | Columnol53nnMSTPTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.28.3.1.2 | Columnol53nnMSTPTrunkIndex | read-only | mandatory | A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular va… |
| 1.3.6.1.4.1.49.2.3.1.4.4.29 | Nodeol51nnMTPCL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1 | Tableol51nnMTPCLModTable | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPCL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1 | Rowol51nnMTPCLModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPCL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.1 | Columnol51nnMTPCLModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.2 | Columnol51nnMTPCLModMonitorConn | read-write | mandatory | When both connectors are on the same network: Setting this object to connector-1 allows the EMM to monitor the port statistics of port 1-12 on a per-port basis… |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.3 | Columnol51nnMTPCLModConn1Network | read-write | mandatory | The network that this connector is attached to. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.4 | Columnol51nnMTPCLModConn2Network | read-write | mandatory | The network that this connector is attached to. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.5 | Columnol51nnMTPCLModConn1DipNetwork | read-only | mandatory | The network indicated by the connector dip switch. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.6 | Columnol51nnMTPCLModConn2DipNetwork | read-only | mandatory | The network indicated by the connector dip switch. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.7 | Columnol51nnMTPCLModAutoPartition | read-write | mandatory | This object holds the consecutive collision count limit value. The module goes into the auto-partition mode whenever the consecutive collision count exceeds th… |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2 | Tableol51nnMTPCLPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1 | Rowol51nnMTPCLPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPCL port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.1 | Columnol51nnMTPCLPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.2 | Columnol51nnMTPCLPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.3 | Columnol51nnMTPCLPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the … |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.4 | Columnol51nnMTPCLPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.5 | Columnol51nnMTPCLPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.6 | Columnol51nnMTPCLPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.7 | Columnol51nnMTPCLPortLinkInteg | read-write | mandatory | The current link integrity configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.8 | Columnol51nnMTPCLPortDipLinkInteg | read-only | mandatory | The link integrity configuration as indicated by this dip switch. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30 | Nodeol52nnBTT | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1 | Tableol52nnBTTModTable | not-accessible | mandatory | A table of module-specific information for each 52nnB-TT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1.1 | Rowol52nnBTTModEntry | not-accessible | mandatory | A list of module-specific information about a specific 52nnB-TT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.1 | Columnol52nnBTTModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.2 | Columnol52nnBTTModBridgeType | read-only | mandatory | Whether the bridge is a source-routing bridge or a source-routing-transparent bridge. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.3 | Columnol52nnBTTModSoftwareVersion | read-only | mandatory | The version number of the software loaded into the module's flash chips. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.4 | Columnol52nnBTTModSRBridgeNo | read-only | mandatory | The module's source routing bridge number. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.5 | Columnol52nnBTTModNetworkStatus | read-only | mandatory | The status of the ring containing this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2 | Tableol52nnBTTPortTable | not-accessible | mandatory | A table of port-specific for each port of each 52nnB-TT module i the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1 | Rowol52nnBTTPortEntry | not-accessible | mandatory | A list of port-specific information about a specific 52nnB-TT port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.1 | Columnol52nnBTTPortSlotIndex | read-only | mandatory | The slot number for this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.2 | Columnol52nnBTTPortIndex | read-only | mandatory | The port number for this port within this slot. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.3 | Columnol52nnBTTPortConnector | read-write | mandatory | The port connector. Notice that setting port connector available only for the front pannel port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.4 | Columnol52nnBTTPortSTAPState | read-only | mandatory | The port connector. Notice that setting port connector available only for the front pannel port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.5 | Columnol52nnBTTPortIpAddress | read-only | mandatory | The IP address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.6 | Columnol52nnBTTPortMACAddress | read-only | mandatory | A 6 octet address that uniquely identifies this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.7 | Columnol52nnBTTPortThroughput | read-only | mandatory | Port throughput measured in Kbytes per second. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.8 | Columnol52nnBTTPortForwarding | read-only | mandatory | Port forwarding rate measured in frames per second. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.9 | Columnol52nnBTTPortSRRingNo | read-only | mandatory | The port's source routing ring number. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.10 | Columnol52nnBTTPortRingSpeed | read-write | mandatory | The ring's bandwidth. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.3 | Tableol52nnBTTTrunkTable | not-accessible | mandatory | A table that contains trunk-specific information for each trunk on each 52nnB-TT in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.3.1 | Rowol52nnBTTTrunkEntry | not-accessible | mandatory | A list of information about a specific Trunk on a 52nnB-TT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.3.1.1 | Columnol52nnBTTTrunkSlotIndex | read-only | mandatory | The slot number of this module. Its value ranges between 1 and olConcNumSlots. |
| 1.3.6.1.4.1.49.2.3.1.4.4.30.3.1.2 | Columnol52nnBTTTrunkIndex | read-only | mandatory | The trunk number of this module. Its value ranges between 1 and olModNumTrunks. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31 | Nodeol51nnIx | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1 | Tableol51nnIxModTable | not-accessible | mandatory | A table of module-specific information for each 51nnI-x module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1.1 | Rowol51nnIxModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnI-x module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.1 | Columnol51nnIxModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.2 | Columnol51nnIxModSwType | read-only | mandatory | The software currently loaded and executing has the module operating as a Bridge, Switch or Router. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.3 | Columnol51nnIxModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.4 | Columnol51nnIxModDipPromDefaults | read-only | mandatory | The current module configuration with respect to default PROM values as specified by dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.5 | Columnol51nnIxModProtocols | read-only | mandatory | A textual description of the protocols supported by this module |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2 | Tableol51nnIxPortTable | not-accessible | mandatory | A table of port-specific information for each port of each 51nnI-x module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1 | Rowol51nnIxPortEntry | not-accessible | mandatory | A list of port-specific information about a specific 51nnI-x port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.1 | Columnol51nnIxPortSlotIndex | read-only | mandatory | The slot number for this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.2 | Columnol51nnIxPortIndex | read-only | mandatory | The port number for this port within this slot. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.3 | Columnol51nnIxPortDipAdminState | read-only | mandatory | The state of this port as indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.4 | Columnol51nnIxPortSTAPState | read-only | mandatory | The current IEEE 802.1d Spanning Tree Algorithm and Protocol state (STAP) of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.5 | Columnol51nnIxPortIpAddress | read-only | mandatory | The IP Address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.6 | Columnol51nnIxPortDipNetwork | read-only | mandatory | The network for this port as specified by this port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.7 | Columnol51nnIxPortDefNetwork | read-only | mandatory | The network for this port as specified by the OEIM's non-volatile storage. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32 | Nodeol52nnMMGT | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1 | Tableol52nnMMGTModTable | not-accessible | mandatory | A table that contains module information about each 52nnM-MGT in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1 | Rowol52nnMMGTModEntry | not-accessible | mandatory | A list of module information for each 52nnM-MGT in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.1 | Columnol52nnMMGTModSlotIndex | read-only | mandatory | The slot number of this module. Its value ranges between 1 and olConcNumSlots. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.2 | Columnol52nnMMGTModMasterPriority | read-write | mandatory | The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive un… |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.3 | Columnol52nnMMGTModMasterStatus | read-only | mandatory | The mastership status of this agent. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.4 | Columnol52nnMMGTModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this module. The station address is the MAC address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.5 | Columnol52nnMMGTModRingSpeed | read-write | mandatory | The ring's bandwidth. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.6 | Columnol52nnMMGTModNetworkStatus | read-only | mandatory | The status of the ring containing this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.7 | Columnol52nnMMGTModMasterNetwork | read-write | mandatory | The network that this module should assign itself to upon becoming master if the module was previously a slave. no-change(25) indicates that the module should … |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.8 | Columnol52nnMMGTModLocalMACAddress | read-write | mandatory | A MAC address with the locally administered bit set to one. Setting this value to an invalid address will return invalidData error. An invalid address is a val… |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.9 | Columnol52nnMMGTModMACAddressType | read-write | mandatory | The desired MAC address for this agent. burned-in(1) indicates that the factory setting as defined in ol52nnMMGTModStationAddr should be used. locally-administ… |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.10 | Columnol52nnMMGTModActiveMACAddress | read-only | mandatory | A actual MAC address that is being used by this agent. This is the MAC address of port 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.2 | Tableol52nnMMGTPortTable | not-accessible | mandatory | A table that contains port-specific information for each port on each 52nnM-MGT in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.2.1 | Rowol52nnMMGTPortEntry | not-accessible | mandatory | A list of information about a specific port on a 52nnM-MGT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.2.1.1 | Columnol52nnMMGTPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.2.1.2 | Columnol52nnMMGTPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.2.1.3 | Columnol52nnMMGTPortIpAddress | read-only | mandatory | The IP address associated with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3 | Tableol52nnMMGTTrunkTable | not-accessible | mandatory | A table that contains trunk-specific information for each trunk on each 52nnM-MGT in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3.1 | Rowol52nnMMGTTrunkEntry | not-accessible | mandatory | A list of information about a specific Trunk on a 52nnM-MGT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.1 | Columnol52nnMMGTTrunkSlotIndex | read-only | mandatory | The slot number of this module. Its value ranges between 1 and olConcNumSlots. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.2 | Columnol52nnMMGTTrunkIndex | read-only | mandatory | The slot number of this module. Its value ranges between 1 and olModNumTrunks. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.3 | Columnol52nnMMGTTrunkCableMon | read-write | mandatory | The cable monitor configuration for this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.4 | Columnol52nnMMGTTrunkNetMapState | read-write | mandatory | The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate… |
| 1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.5 | Columnol52nnMMGTTrunkExtBcnRecovery | read-write | mandatory | Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which… |
| 1.3.6.1.4.1.49.2.3.1.4.4.33 | Nodeol50nnMHCTL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1 | Tableol50nnMHCTLModTable | not-accessible | mandatory | A table that contains information about each 50nnM-HCTL in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1 | Rowol50nnMHCTLModEntry | not-accessible | mandatory | A list of information for each 50nnM-HCTL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.1 | Columnol50nnMHCTLModSlotIndex | read-only | mandatory | The slot number for this module. The value should be 7. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.2 | Columnol50nnMHCTLModOperState | read-only | mandatory | The operational state of the 50nnM-HCTL module. Specifically, this is an indicator of whether the 50nnM-HCTL module is providing clock signals to the backplane… |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.3 | Columnol50nnMHCTLModClockStatus | read-only | mandatory | The current status of the on-board clocks on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.4 | Columnol50nnMHCTLModTempStatus | read-only | mandatory | The temperature as detected by the probe on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.5 | Columnol50nnMHCTLModPDBStatus | read-only | mandatory | Indicates whether this 6-slot concentrator contains a power distribution board that supports powersupply redundancy. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.6 | Columnol50nnMHCTLModDipCh1ActCol | read-only | mandatory | The Ethernet channel 1 activity/collision LED configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.7 | Columnol50nnMHCTLModDipCh2ActCol | read-only | mandatory | The Ethernet channel 2 activity/collision LED configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.8 | Columnol50nnMHCTLModDipCh3ActCol | read-only | mandatory | The Ethernet channel 3 activity/collision LED configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.35 | Nodeoc61nnMCAR | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.35.6 | Tableoc61nnMCARModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 61nnM-CAR module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.35.6.1 | Rowoc61nnMCARModEntry | not-accessible | mandatory | A list of module-specific information about a specific 61nnM-CAR module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.35.6.1.1 | Columnoc61nnMCARModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.35.6.1.2 | Columnoc61nnMCARModSubSlotIndex | read-only | mandatory | The subslot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.35.6.1.3 | Columnoc61nnMCARModBootVersion | read-only | mandatory | The software boot eprom version of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43 | Nodeoc60nnMMGT | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6 | Tableoc60nnMMGTModTable | not-accessible | mandatory | A table that contains module information about each 60nnM-MGT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1 | Rowoc60nnMMGTModEntry | not-accessible | mandatory | A list of module information for each 60nnM-MGT module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1.1 | Columnoc60nnMMGTModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1.2 | Columnoc60nnMMGTModSubSlotIndex | read-only | mandatory | The subslot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1.3 | Columnoc60nnMMGTModBootVersion | read-only | mandatory | The software boot eprom version of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1.4 | Columnoc60nnMMGTModMasterPriority | read-write | mandatory | The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive un… |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1.5 | Columnoc60nnMMGTModMasterStatus | read-only | mandatory | The mastership status of this agent. |
| 1.3.6.1.4.1.49.2.3.1.4.4.43.6.1.6 | Columnoc60nnMMGTModHubSerial | read-only | mandatory | The Hub serial number mastership is presiding over. Zero length string for slaves. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45 | Nodeoc61nnDMGT | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6 | Tableoc61nnDMGTModTable | not-accessible | mandatory | A table that contains information about Ethernet Network Monitor Cards in the ONcore Hub. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1 | Rowoc61nnDMGTModEntry | not-accessible | mandatory | A list of information for an Ethernet Network Monitor Card in the ONcore Hub. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.1 | Columnoc61nnDMGTModSlotIndex | read-only | mandatory | The slot number of this card. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.2 | Columnoc61nnDMGTModSubSlotIndex | read-only | mandatory | The subslot number of this card. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.3 | Columnoc61nnDMGTModBootVersion | read-only | mandatory | The software boot eprom version of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.4 | Columnoc61nnDMGTModIpAddress | read-only | mandatory | The current IP address of this card and the associated interface. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.5 | Columnoc61nnDMGTModSubnetMask | read-only | mandatory | The current subnet mask of this card and the associated interface. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.6 | Columnoc61nnDMGTModDefaultGateway | read-only | mandatory | The current default gateway of this card and the associated interface. Note that a value of 0.0.0.0 indicates that this interface is not con- configured to be … |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.7 | Columnoc61nnDMGTModStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies this card. Note that an address of 00-00-00-00-00-00 is invalid and the module has failed. |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.8 | Columnoc61nnDMGTModInterfaceMode | read-write | mandatory | The desired connectvity mode of this card. When this attribute is set to enabled(1) and the card is set to a network, it will forward messages to and from the … |
| 1.3.6.1.4.1.49.2.3.1.4.4.45.6.1.9 | Columnoc61nnDMGTModRMONHostStatsMode | read-write | mandatory | The desired RMON host staticstics mode of this card. When this attribute is set to enabled, the card will gather RMON host table statistics. Note that when thi… |
| 1.3.6.1.4.1.49.2.3.1.4.4.46 | Nodeoc61nnMFBP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2 | Tableoc61nnMFBPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1 | Rowoc61nnMFBPPortEntry | not-accessible | mandatory | A list of port specific information about this module's ports. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.1 | Columnoc61nnMFBPPortSlotIndex | read-only | mandatory | The slot number of the module assocaited with this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.2 | Columnoc61nnMFBPPortIndex | read-only | mandatory | The port number with respect to the module it resides on. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.3 | Columnoc61nnMFBPPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to redundant-primary or redundant-backup with invalid buddy slot or buddy port will result in an error. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.4 | Columnoc61nnMFBPPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.5 | Columnoc61nnMFBPPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. Valid ports are those ports which are not redundant. The buddy port admin state will be set to redundant. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.6 | Columnoc61nnMFBPPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.2.1.7 | Columnoc61nnMFBPPortHipwr | read-write | mandatory | The current port high power optics mode. Setting this variable to enable(1), will enable the port to drive up to 4K meter fiber cable. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.6 | Tableoc61nnMFBPModTable | not-accessible | mandatory | A list of module specific information about this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.6.1 | Rowoc61nnMFBPModEntry | not-accessible | mandatory | Values to describe module specific inormation. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.6.1.1 | Columnoc61nnMFBPModSlotIndex | read-only | mandatory | The slot index of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.6.1.2 | Columnoc61nnMFBPModSubSlotIndex | read-only | mandatory | The subslot index of this module. (e.g. mother boards have subslot index equals to one. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.6.1.3 | Columnoc61nnMFBPModBootVersion | read-only | mandatory | The software boot eprom version of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.46.6.1.4 | Columnoc61nnMFBPModDipNVRam | read-only | mandatory | The Non-Volatile RAM dip switch setting for this module. Setting this object to enable(1) will cause the module to be configured according to the configuration… |
| 1.3.6.1.4.1.49.2.3.1.4.4.47 | Nodeoc61nnMTPL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2 | Tableoc61nnMTPLPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1 | Rowoc61nnMTPLPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 61nnM-TPL port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.1 | Columnoc61nnMTPLPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.2 | Columnoc61nnMTPLPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.3 | Columnoc61nnMTPLPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the … |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.4 | Columnoc61nnMTPLPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.5 | Columnoc61nnMTPLPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.6 | Columnoc61nnMTPLPortDipNetwork | read-only | mandatory | The network indicated by the port's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.7 | Columnoc61nnMTPLPortLinkInteg | read-write | mandatory | The current link integrity configuration for this port. Setting this object to enabled(1) makes it conform to the 10BASE-T link integrity standard. Setting thi… |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.2.1.8 | Columnoc61nnMTPLPortAutoPolarity | read-write | mandatory | The current auto polarity configuration for this port. Setting this object to enabled(1) causes the module to switch the port polarity automatically when the p… |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.6 | Tableoc61nnMTPLModTable | not-accessible | mandatory | A list of module-specific information about a specific 61nnM-TPL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.6.1 | Rowoc61nnMTPLModEntry | not-accessible | mandatory | A list of module-specific information about a specific 61nnM-TPL module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.6.1.1 | Columnoc61nnMTPLModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.6.1.2 | Columnoc61nnMTPLModSubSlotIndex | read-only | mandatory | The subslot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.6.1.3 | Columnoc61nnMTPLModBootVersion | read-only | mandatory | The software boot eprom version of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.47.6.1.4 | Columnoc61nnMTPLModDipNVRam | read-only | mandatory | The Non-Volatile RAM dip switch setting for this module. Enabling this switch will cause the module to be configured according to the configurations that were … |
| 1.3.6.1.4.1.49.2.3.1.4.4.48 | Nodeol51nnMTPLS | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.48.1 | Tableol51nnMTPLSModTable | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPLS module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.1.1 | Rowol51nnMTPLSModEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPLS module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.1.1.1 | Columnol51nnMTPLSModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.1.1.2 | Columnol51nnMTPLSModDipNetwork | read-only | mandatory | The network indicated by the module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.1.1.3 | Columnol51nnMTPLSModAutoPartition | read-write | mandatory | This object holds the consecutive collision count limit value. The module goes into the auto-partition mode whenever the consecutive collision count exceeds th… |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2 | Tableol51nnMTPLSPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1 | Rowol51nnMTPLSPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 51nnM-TPLS port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.1 | Columnol51nnMTPLSPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.2 | Columnol51nnMTPLSPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.3 | Columnol51nnMTPLSPortAdminState | read-write | mandatory | The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the … |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.4 | Columnol51nnMTPLSPortDipAdminState | read-write | mandatory | The admin state of this port as indicated by the dip switches. i.e. This object indicates whether the port will initialize to enabled or disabled when the modu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.5 | Columnol51nnMTPLSPortDipSecurity | read-only | mandatory | The security state of this port as indicated by the dip switches. i.e. This object indicates whether the port's security state will initialize to enabled (full… |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.6 | Columnol51nnMTPLSPortBuddySlot | read-write | mandatory | The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.7 | Columnol51nnMTPLSPortBuddyPort | read-write | mandatory | The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically … |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.8 | Columnol51nnMTPLSPortLinkInteg | read-write | mandatory | The current link integrity configuration for this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.48.2.1.9 | Columnol51nnMTPLSPortDipLinkInteg | read-only | mandatory | The link integrity configuration as indicated by this module's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50 | Nodeoc60nnMRCTL | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.50.1 | Tableol60nnMRCTLModTable | not-accessible | mandatory | A table that contains information about the Controller in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.1.1 | Rowol60nnMRCTLModEntry | not-accessible | mandatory | A list of information for the Controller module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.1.1.1 | Columnol60nnMRCTLModSlotIndex | read-only | mandatory | The slot number for this module. Note that this module will always be in slot 17. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.1.1.2 | Columnol60nnMRCTLModOperState | read-only | mandatory | The operational state of the Controller module. Specifically, this is an indicator of whether the Controller module is providing clock signals to the backplane… |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.1.1.3 | Columnol60nnMRCTLModClockStatus | read-only | mandatory | The current status of the on-board clocks on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.1.1.4 | Columnol60nnMRCTLModTempStatus | read-only | mandatory | The overall temperature status for this concentrator as detected by this module. This object's value is an aggregate of all temperature probes located within t… |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6 | Tableoc60nnMRCTLModTable | not-accessible | mandatory | A table that contains information about the Controller in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1 | Rowoc60nnMRCTLModEntry | not-accessible | mandatory | A list of information for the Controller module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.1 | Columnoc60nnMRCTLModSlotIndex | read-only | mandatory | The slot number for this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.2 | Columnoc60nnMRCTLModSubSlotIndex | read-only | mandatory | The subslot number for this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.3 | Columnoc60nnMRCTLModBootVersion | read-only | mandatory | The software boot eprom version of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.4 | Columnoc60nnMRCTLModOperState | read-only | mandatory | The operational state of the Controller module. Specifically, this is an indicator of whether the Controller module is providing clock signals to the backplane… |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.5 | Columnoc60nnMRCTLModClockStatus | read-only | mandatory | The current status of the on-board clocks on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.6 | Columnoc60nnMRCTLModTempStatus | read-only | mandatory | The overall temperature status for the concentrator as detected by this module. This object's value is an aggregate of all the temperature probes located withi… |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.7 | Columnoc60nnMRCTLModAtoDConverterStatus | read-only | mandatory | The current status of the on-board A/D converter. Typically, when this object has a value of faulty(2), it is because the value obtained from the A/D converter… |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.8 | Columnoc60nnMRCTLModPS1Status | read-only | mandatory | The current status of powersupply 1. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.9 | Columnoc60nnMRCTLModPS2Status | read-only | mandatory | The current status of powersupply 2. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.10 | Columnoc60nnMRCTLModPS3Status | read-only | mandatory | The current status of powersupply 3. |
| 1.3.6.1.4.1.49.2.3.1.4.4.50.6.1.11 | Columnoc60nnMRCTLModPS4Status | read-only | mandatory | The current status of powersupply 4. |
| 1.3.6.1.4.1.49.2.3.1.4.4.51 | Nodeol50nnMRCLS | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.51.1 | Tableol50nnMRCLSModTable | not-accessible | mandatory | A table that contains information about each Redundant Controller in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.51.1.1 | Rowol50nnMRCLSModEntry | not-accessible | mandatory | A list of information for each Load Sharing Redundant controller module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.51.1.1.1 | Columnol50nnMRCLSModSlotIndex | read-only | mandatory | The slot number for this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.51.1.1.2 | Columnol50nnMRCLSModOperState | read-only | mandatory | The operational state of the Load Sharing Redudant Controller module. Specifically, this is an indicator of whether the Load Sharing Redudant Controller module… |
| 1.3.6.1.4.1.49.2.3.1.4.4.51.1.1.3 | Columnol50nnMRCLSModClockStatus | read-only | mandatory | The current status of the on-board clocks on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.51.1.1.4 | Columnol50nnMRCLSModTempStatus | read-only | mandatory | The temperature as detected by the probe on this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52 | Nodeol41nnHMTP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.52.1 | Tableol41nnHMTPModTable | not-accessible | mandatory | A list of module-specific information associated with a particular ol41nnHMTP or ol41nnHMTP-FL module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.1.1 | Rowol41nnHMTPModEntry | not-accessible | mandatory | A module entry containing objects that describe the module level for that particular module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.1.1.1 | Columnol41nnHMTPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.1.1.2 | Columnol41nnHMTPModSerialNo | read-only | mandatory | The serial number of this module, as entered by the user through the Management interface. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.1.1.3 | Columnol41nnHMTPModProtocols | read-only | mandatory | A list of the various protocols supported by the module's agent. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.1.1.4 | Columnol41nnHMTPModIpAddress | read-only | mandatory | The IP Address of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.2 | Tableol41nnHMTPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.2.1 | Rowol41nnHMTPPortEntry | not-accessible | mandatory | A port entry containing objects that describe this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.2.1.1 | Columnol41nnHMTPPortSlotIndex | read-only | mandatory | The slot (stack) number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.2.1.2 | Columnol41nnHMTPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.2.1.3 | Columnol41nnHMTPPortReset | read-write | mandatory | Used to reset the port's '802.3 state machine', which will re-enable a disabled port and/or reconnect a partitioned port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.52.2.1.4 | Columnol41nnHMTPPortLinkInteg | read-write | mandatory | The port's (good) link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. … |
| 1.3.6.1.4.1.49.2.3.1.4.4.53 | Nodeol41nnHETP | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.53.1 | Tableol41nnHETPModTable | not-accessible | mandatory | A list of module-specific information associated with a particular ol41nnHETP module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.1.1 | Rowol41nnHETPModEntry | not-accessible | mandatory | A module entry containing objects that describe the module level for that particular module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.1.1.1 | Columnol41nnHETPModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.1.1.2 | Columnol41nnHETPModSerialNo | read-only | mandatory | The serial number of this module, as entered by the user through the Management interface. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.2 | Tableol41nnHETPPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.2.1 | Rowol41nnHETPPortEntry | not-accessible | mandatory | A port entry containing objects that describe this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.2.1.1 | Columnol41nnHETPPortSlotIndex | read-only | mandatory | The slot (stack) number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.2.1.2 | Columnol41nnHETPPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.2.1.3 | Columnol41nnHETPPortReset | read-write | mandatory | Used to reset the port's '802.3 state machine', which will re-enable a disabled port and/or reconnect a partitioned port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.53.2.1.4 | Columnol41nnHETPPortLinkInteg | read-write | mandatory | The port's (good) link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62 | Nodeol52nnMEC | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1 | Tableol52nnMECModTable | not-accessible | mandatory | A list of module-specific information associated with a particular 52nnM-EC module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1 | Rowol52nnMECModEntry | not-accessible | mandatory | A description of the 52nnM-EC module attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.1 | Columnol52nnMECModSlotIndex | read-only | mandatory | The slot number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.2 | Columnol52nnMECModSoftwareVersion | read-only | mandatory | The version number of the software. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.3 | Columnol52nnMECModSystemStatusCode | read-only | mandatory | A 43 octet indication of the current applicable IBM 3174 System Status Code. For more information consult the 52nnM-EC reference manual. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.4 | Columnol52nnMECModRingSpeed | read-write | mandatory | The ring's bandwidth in Mega-bits per second. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.5 | Columnol52nnMECModNetworkStatus | read-only | mandatory | The status of the ring containing this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.6 | Columnol52nnMECModIpAddress | read-only | mandatory | The IP Address of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.1.1.7 | Columnol52nnMECModMACStationAddr | read-only | mandatory | A 6 octet address that uniquely identifies the MAC address of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.2 | Tableol52nnMECPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.2.1 | Rowol52nnMECPortEntry | not-accessible | mandatory | A description of this module's port attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.2.1.1 | Columnol52nnMECPortSlotIndex | read-only | mandatory | The slot number of this port's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.2.1.2 | Columnol52nnMECPortIndex | read-only | mandatory | The port number of this port. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.3 | Tableol52nnMECTrunkTable | not-accessible | mandatory | A list of trunk-specific information about each trunk for this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.3.1 | Rowol52nnMECTrunkEntry | not-accessible | mandatory | A description of 52nnM-EC trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.3.1.1 | Columnol52nnMECTrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.62.3.1.2 | Columnol52nnMECTrunkIndex | read-only | mandatory | The trunk number for this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65 | Nodeol53nnMTDDI | |||
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1 | Tableol53nnMTDDIModTable | not-accessible | mandatory | A list of module attributes that apply to this model. To access an ol53nnMTDDIModTable entry, the ol53nnMTDDIModSlotIndex attribute is used. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1 | Rowol53nnMTDDIModEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-TDDI module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1.1 | Columnol53nnMTDDIModSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1.2 | Columnol53nnMTDDIModDownStreamModule | read-only | mandatory | Down stream slot (transmit to) |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1.3 | Columnol53nnMTDDIModUpStreamModule | read-only | mandatory | Down stream slot (receive from) |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1.4 | Columnol53nnMTDDIModDownStreamOperPath | read-only | mandatory | transmit DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1.5 | Columnol53nnMTDDIModUpStreamOperPath | read-only | mandatory | receive DBA (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.1.1.6 | Columnol53nnMTDDIModRingInfo | read-only | mandatory | An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only) |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2 | Tableol53nnMTDDIPortTable | not-accessible | mandatory | A table of port-specific information for each port of this module type. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1 | Rowol53nnMTDDIPortEntry | not-accessible | mandatory | A list of module-specific information about a specific 53nnM-TDDI port in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.1 | Columnol53nnMTDDIPortSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.2 | Columnol53nnMTDDIPortIndex | read-only | mandatory | A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular valu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.3 | Columnol53nnMTDDIPortConfig | read-write | mandatory | Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave por… |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.4 | Columnol53nnMTDDIPortPcmState | read-only | mandatory | (refer to ANSI SMT 9.6.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.5 | Columnol53nnMTDDIPortConnectState | read-only | mandatory | An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Wit… |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.6 | Columnol53nnMTDDIPortNeighbor | read-only | mandatory | The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.7 | Columnol53nnMTDDIPortRemoteMACIndicated | read-only | mandatory | The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT … |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.8 | Columnol53nnMTDDIPortBSFlag | read-only | mandatory | The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.9 | Columnol53nnMTDDIPortPCWithhold | read-only | mandatory | PC-Withhold, (refer to ANSI SMT 9.4.1). |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.2.1.10 | Columnol53nnMTDDIPortLerCondition | read-only | mandatory | This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.3 | Tableol53nnMTDDITrunkTable | not-accessible | mandatory | FDDI module specific trunk table variables. At present there are none. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.3.1 | Rowol53nnMTDDITrunkEntry | not-accessible | mandatory | A description of 53nnM-TDDI trunk attributes. |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.3.1.1 | Columnol53nnMTDDITrunkSlotIndex | read-only | mandatory | A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index i… |
| 1.3.6.1.4.1.49.2.3.1.4.4.65.3.1.2 | Columnol53nnMTDDITrunkIndex | read-only | mandatory | A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular va… |
| 1.3.6.1.4.1.49.2.3.1.4.5 | TableolModSummaryTable | not-accessible | mandatory | A table of condensed module information. |
| 1.3.6.1.4.1.49.2.3.1.4.5.1 | RowolModSummaryEntry | not-accessible | mandatory | A summary of all the generic and value added information associated with this module. |
| 1.3.6.1.4.1.49.2.3.1.4.5.1.1 | ColumnolModSummarySlotIndex | read-only | mandatory | The slot number of this module that this summary pertains to. |
| 1.3.6.1.4.1.49.2.3.1.4.5.1.2 | ColumnolModSummaryInfo | read-only | mandatory | A summary of all information relating to this module in condensed format. The condensed format is only as large as needed to hence the largest value which usua… |
| 1.3.6.1.4.1.49.2.3.1.4.6 | TableocModTable | not-accessible | mandatory | A table that contains generic information about every module that is present within the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1 | RowocModEntry | not-accessible | mandatory | A list of information for each module in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.1 | ColumnocModSlotIndex | read-only | mandatory | The unique slot number of this module. Its value ranges between 1 and olConcNumSlots and remains constant at least from one re-initialization of the entity's n… |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.2 | ColumnocModSubSlotIndex | read-only | mandatory | The unique subslot number of this module. Its value ranges between 1 and the value of ocModNumSubSlots for the mother board in this slot (ocModNumSubSlots.<slo… |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.3 | ColumnocModType | read-only | mandatory | The unique type identifier for this module. This type is used to identify the branch in olSpecMods (see below). module-unmanageable(1) means that only the foll… |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.4 | ColumnocModClass | read-only | mandatory | The class of this module. The class defines the internal data structure used to manage this module. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.5 | ColumnocModDescr | read-only | mandatory | A textual string containing information about the module. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.6 | ColumnocModVersion | read-only | mandatory | The software version number of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.7 | ColumnocModVendor | read-only | mandatory | The vendor of this module. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.8 | ColumnocModResetModule | read-write | mandatory | Setting this object to reset(2) causes this module to reset. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.9 | ColumnocModConfigToDips | read-write | mandatory | Setting this object to configure(2) causes this module to configure based on the dip switch settings. Note, if the NV dip switch (if applicable) is set to conf… |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.10 | ColumnocModConfigured | read-only | mandatory | This object indicates whether this module has already been configured. An unconfigured module is configured to a safe state (ports are disabled and the module … |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.11 | ColumnocModNetwork | read-write | mandatory | The network that this module is attached to. Setting this module to a value that it does not support will return an invalidData error. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.12 | ColumnocModNetworkType | read-only | mandatory | The network type of this module. The network type reflects the valid values for ocModNetwork. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.13 | ColumnocModStatus | read-only | mandatory | The module's status. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.14 | ColumnocModNumPorts | read-only | mandatory | The number of ports on this module. Note, ports may be physical ports like 10BASE-T ports, or logical, like the bridge module ports. |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.15 | ColumnocModNumTrunks | read-only | mandatory | The number of trunks on this module. Note, trunks are links that are, by definition, backbone connections. Examples of trunks are ring in and ring out ports fo… |
| 1.3.6.1.4.1.49.2.3.1.4.6.1.16 | ColumnocModNumSubSlots | read-only | mandatory | The number of possible submodules that can exist in this slot. |
| 1.3.6.1.4.1.49.2.3.1.5 | NodeolNets | |||
| 1.3.6.1.4.1.49.2.3.1.5.1 | NodeolNet | |||
| 1.3.6.1.4.1.49.2.3.1.5.1.1 | TableolNetDPTable | not-accessible | mandatory | A table that contains information linking physical backplane allocation to logical networks. This information is useful: (1) to determine the physical allocati… |
| 1.3.6.1.4.1.49.2.3.1.5.1.1.1 | RowolNetDPEntry | not-accessible | mandatory | A list of information about each data path in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.1.1.1.1 | ColumnolNetDPDataPath | read-only | mandatory | The data path on the backplane. Data paths between different protocols overlap. That is, an ethernet data path will overlap with multiple token ring and fddi d… |
| 1.3.6.1.4.1.49.2.3.1.5.1.1.1.2 | ColumnolNetDPNetID | read-only | mandatory | The network that this data path corresponds to. If the data path is not being used at all, notUsed(1) is the return value. If the data path is being used by an… |
| 1.3.6.1.4.1.49.2.3.1.5.1.2 | TableolNetSecurityMACTable | not-accessible | mandatory | A table of security configuration parameters and MAC addresses associated with every port with security configured in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.1.2.1 | RowolNetSecurityMACEntry | not-accessible | mandatory | A list of security configuration parameters and MAC addresses associated with each port with security configured in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.1.2.1.1 | ColumnolNetSecurityMACSlotIndex | read-only | mandatory | The slot number that contains this port. |
| 1.3.6.1.4.1.49.2.3.1.5.1.2.1.2 | ColumnolNetSecurityMACPortIndex | read-only | mandatory | The port number within this slot. |
| 1.3.6.1.4.1.49.2.3.1.5.1.2.1.3 | ColumnolNetSecurityMACAddress | read-write | mandatory | The security MAC address assigned to this port. |
| 1.3.6.1.4.1.49.2.3.1.5.1.2.1.4 | ColumnolNetSecurityMACMode | read-write | mandatory | The desired security mode for this port/address. |
| 1.3.6.1.4.1.49.2.3.1.5.1.2.1.5 | ColumnolNetSecurityMACStatus | read-write | mandatory | Each instance of the olNetSecurityMACTable associated with this olNetSecurityMACEntry (slot, port, and address) will be deleted by the agent if this olNetSecur… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3 | NodeolNetOlSec | |||
| 1.3.6.1.4.1.49.2.3.1.5.1.3.1 | TableolNetOlSecAddrTable | not-accessible | mandatory | A table of security MAC addresses. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.1.1 | RowolNetOlSecAddrEntry | not-accessible | mandatory | Security MAC addresses indexed by slot, port, and MAC address. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.1.1.1 | ColumnolNetOlSecAddrSlotIndex | read-only | mandatory | The slot number index (used along with the port and address indices). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.1.1.2 | ColumnolNetOlSecAddrPortIndex | read-only | mandatory | The port number index (used along with the slot and address indices). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.1.1.3 | ColumnolNetOlSecAddrAddress | read-write | mandatory | The security MAC address index (used along with the slot and port indices). Note that there may be multiple addresses associated with a single port. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.1.1.4 | ColumnolNetOlSecAddrStatus | read-write | mandatory | Setting this object to valid(1) will cause the corresponding security MAC address to be associated with the given port. Setting this object to invalid(2) will … |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2 | TableolNetOlSecControlTable | not-accessible | mandatory | A table of security configuration parameters pertaining to a specific port. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1 | RowolNetOlSecControlEntry | not-accessible | mandatory | Security configuration parameters pertaining to a specific port (indexed by slot and port). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.1 | ColumnolNetOlSecControlSlotIndex | read-only | mandatory | The slot number index (used along with the port index). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.2 | ColumnolNetOlSecControlPortIndex | read-only | mandatory | The port number index (used along with the slot index). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.3 | ColumnolNetOlSecControlMode | read-write | mandatory | The desired security mode for this port. Setting this object to enable(1) is equivalent to setting the 'SecType' object (see below) to full(1), since both acti… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.4 | ColumnolNetOlSecControlSecType | read-write | mandatory | Setting this object enables a certain type of security for this port: Eavesdropping Security-only, Intrusion Security-only, or Full. Note that setting this obj… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.5 | ColumnolNetOlSecControlActOnIntr | read-write | mandatory | This object can be used to get or set the port-action-on- intrusion flag on a per-port basis. When an Intrusion Security breach is attempted on a port, the Sec… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.6 | ColumnolNetOlSecControlClearAddrs | read-write | mandatory | When this object is set to clear-all-addrs(1) then all of the security MAC addresses associated with this port will be cleared. Note that this will not change … |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.2.1.7 | ColumnolNetOlSecControlAutolearnMask | read-write | mandatory | This mask is used when autolearning is performed to determine whether the nMM should learn any security MAC addresses for this port. If this object is set to e… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.3 | NodeolNetOlSecAutolearn | |||
| 1.3.6.1.4.1.49.2.3.1.5.1.3.3.1 | ScalarolNetOlSecAutolearnTrigger | read-write | mandatory | When this object is set to autolearn(1) then the nMM will capture a snapshot of its MAC address cache for those ports whose 'AutolearnMask' object is disabled(… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.3.2 | ScalarolNetOlSecAutolearnDownload | read-write | mandatory | When this object is set to download-addresses(1) then the nMM will download its snapshot of addresses to the Security Module. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.4 | TableolNetOlSecLearnTable | not-accessible | mandatory | A table of security MAC addresses which have been autolearned on the nMM by taking a snapshot of its MAC address cache. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.4.1 | RowolNetOlSecLearnEntry | not-accessible | mandatory | Security MAC addresses which have been autolearned (indexed by slot, port, and address). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.4.1.1 | ColumnolNetOlSecLearnSlotIndex | read-only | mandatory | The slot number index (used along with the port and address indices). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.4.1.2 | ColumnolNetOlSecLearnPortIndex | read-only | mandatory | The port number index (used along with the slot and address indices). |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.4.1.3 | ColumnolNetOlSecLearnAddress | read-write | mandatory | The security MAC address index (used along with the slot and port indices). Note that there may be multiple addresses per port. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.4.1.4 | ColumnolNetOlSecLearnStatus | read-write | mandatory | Setting this object to valid(1) will cause the corresponding security MAC address to be included in the snapshot of autolearned addresses. Setting this object … |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5 | TableolNetOlSecIntruderTable | not-accessible | mandatory | A table of entries which describe Intrusion Security breach attempts. This table contains the same info as the following table, the difference being that this … |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1 | RowolNetOlSecIntruderEntry | not-accessible | mandatory | A table of entries which describe Intrusion Security breach attempts. The index is simply the chronological order in which the attempt occurred; e.g. index 1 c… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1.1 | ColumnolNetOlSecIntruderChronIndex | read-only | mandatory | The chronological index into the Intruder Table. An index of 1 corresponds to the first Intrusion Security breach attempt, an index of 2 corresponds to the nex… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1.2 | ColumnolNetOlSecIntruderSlot | read-only | mandatory | The slot number on which the intrusion attempt occurred. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1.3 | ColumnolNetOlSecIntruderPort | read-only | mandatory | The port number on which the intrusion attempt occurred. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1.4 | ColumnolNetOlSecIntruderAddress | read-only | mandatory | The address of the intruder, if known. If it is not known then this object will equal all zeroes. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1.5 | ColumnolNetOlSecIntruderTimeSince | read-only | mandatory | The time in hundredths of a second since the Intrusion Security breach attempt took place. For example, if it is equal to 500 ticks then the intrusion attempt … |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.5.1.6 | ColumnolNetOlSecIntruderDisabled | read-only | mandatory | This object indicates whether the port on which the intrusion attempt took place was automatically disabled. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6 | TableolNetOlSecPortIntrTable | not-accessible | mandatory | A table of entries which describe Intrusion Security breach attempts. This table contains the same info as the previous table, the difference being the indices… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1 | RowolNetOlSecPortIntrEntry | not-accessible | mandatory | A table of entries which describe Intrusion Security breach attempts. The indices are the slot, port, and chronological order in time of the intrusion attempt. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1.1 | ColumnolNetOlSecPortIntrSlotIndex | read-only | mandatory | The slot number on which the intrusion attempt occurred. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1.2 | ColumnolNetOlSecPortIntrPortIndex | read-only | mandatory | The port number on which the intrusion attempt occurred. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1.3 | ColumnolNetOlSecPortIntrChronIndex | read-only | mandatory | The chronological index into the Intruder Table. An index of 1 corresponds to the first Intrusion Security breach attempt for that port, an index of 2 correspo… |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1.4 | ColumnolNetOlSecPortIntrAddress | read-only | mandatory | The address of the intruder, if known. If it is not known then this object will equal all zeroes. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1.5 | ColumnolNetOlSecPortIntrTimeSince | read-only | mandatory | The time in hundredths of a second since the Intrusion Security breach attempt took place. For example, if it is equal to 500 ticks then the intrusion attempt … |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.6.1.6 | ColumnolNetOlSecPortIntrDisabled | read-only | mandatory | This object indicates whether the port on which the intrusion attempt took place was automatically disabled. |
| 1.3.6.1.4.1.49.2.3.1.5.1.3.7 | NodeolNetOlSecTrap | |||
| 1.3.6.1.4.1.49.2.3.1.5.1.3.7.1 | ScalarolNetOlSecTrapReason | read-only | mandatory | This object is included in security traps to specify the reason for the trap. When this object is read it will represent the reason for the most recently gener… |
| 1.3.6.1.4.1.49.2.3.1.5.2 | NodeolEnet | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.1 | TableolEnetStatsTable | not-accessible | mandatory | A table that contains statistical information about Ethernet (IEEE 802.3) networks. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1 | RowolEnetStatsEntry | not-accessible | mandatory | A list of statistical information about each Ethernet (IEEE 802.3) network in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.1 | ColumnolEnetStatsNetID | read-only | mandatory | The network index that uniquely identifies this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.2 | ColumnolEnetStatsFramesRcvdOks | read-only | mandatory | The count of frames that were successfully received by this network. This counter does not include frames received in error. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.3 | ColumnolEnetStatsOctetsRcvdOks | read-only | mandatory | The count of the number of octets that were successfully received by this network. This counter does not include octets that were part of frames that were rece… |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.4 | ColumnolEnetStatsMcastRcvdOks | read-only | mandatory | The count of the number of multicast frames successfully received by this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.5 | ColumnolEnetStatsBcastRcvdOks | read-only | mandatory | The count of the number of broadcast frames successfully received by this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.6 | ColumnolEnetStatsFrameTooLongs | read-only | mandatory | The count of the number of frames received by this network that exceeds the maximum permitted Ethernet (802.3) frame size. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.7 | ColumnolEnetStatsAlignmentErrors | read-only | mandatory | The count of the number of frames received by this network that did not pass the frame check sequence (FCS) check and that are not an integral number of octets… |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.8 | ColumnolEnetStatsFCSErrors | read-only | mandatory | The count of the number of frames received by this network that did not pass the frame check sequence (FCS) check and are an integral number of octets. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.9 | ColumnolEnetStatsRunts | read-only | mandatory | The count of the number of frames received by this network that are less than 512 bits long. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.10 | ColumnolEnetStatsLocalColls | read-only | mandatory | The count of the number of times that two or more ports within this concentrator have received traffic simultaneously. |
| 1.3.6.1.4.1.49.2.3.1.5.2.1.1.11 | ColumnolEnetStatsDropEvents | read-only | mandatory | The total number of events in which frames were dropped due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is … |
| 1.3.6.1.4.1.49.2.3.1.5.2.2 | TableolEnetStatsModTable | not-accessible | mandatory | A table of statistical information counted for each module in each Ethernet (IEEE 802.3) network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1 | RowolEnetStatsModEntry | not-accessible | mandatory | A list of statistical information for each port on each Ethernet (IEEE 802.3) network in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.1 | ColumnolEnetStatsModNetID | read-only | mandatory | The unique identifier for this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.2 | ColumnolEnetStatsModSlotIndex | read-only | mandatory | The slot number that contains this module. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.3 | ColumnolEnetStatsModFramesRcvdOks | read-only | mandatory | The count of frames that were successfully received by this module. This counter does not include frames received in error. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.4 | ColumnolEnetStatsModOctetsRcvdOks | read-only | mandatory | The count of the number of octets that were successfully received by this module. This counter does not include octets that were part of frames that were recei… |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.5 | ColumnolEnetStatsModMcastRcvdOks | read-only | mandatory | The count of the number of multicast frames successfully received by this module. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.6 | ColumnolEnetStatsModBcastRcvdOks | read-only | mandatory | The count of the number of broadcast frames successfully received by this module. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.7 | ColumnolEnetStatsModFrameTooLongs | read-only | mandatory | The count of the number of frames received by this module that exceeds the maximum permitted Ethernet (802.3) frame size. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.8 | ColumnolEnetStatsModAlignmentErrors | read-only | mandatory | The count of the number of frames received by this module that did not pass the frame check sequence (FCS) check and that are not an integral number of octets.… |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.9 | ColumnolEnetStatsModFCSErrors | read-only | mandatory | The count of the number of frames received by this module that did not pass the frame check sequence (FCS) check and are an integral number of octets. |
| 1.3.6.1.4.1.49.2.3.1.5.2.2.1.10 | ColumnolEnetStatsModRunts | read-only | mandatory | The count of the number of frames received by this module that are less than 512 bits long. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3 | TableolEnetStatsPortTable | not-accessible | mandatory | A table of statistical information counted for each port in each Ethernet (IEEE 802.3) network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1 | RowolEnetStatsPortEntry | not-accessible | mandatory | A list of statistical information for each port on each Ethernet (IEEE 802.3) network in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.1 | ColumnolEnetStatsPortNetID | read-only | mandatory | The unique identifier for this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.2 | ColumnolEnetStatsPortSlotIndex | read-only | mandatory | The slot number that contains this port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.3 | ColumnolEnetStatsPortIndex | read-only | mandatory | The port number within this slot. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.4 | ColumnolEnetStatsPortFramesRcvdOks | read-only | mandatory | The count of frames that were successfully received by this port. This counter does not include frames received in error. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.5 | ColumnolEnetStatsPortOctetsRcvdOks | read-only | mandatory | The count of the number of octets that were successfully received by this port. This counter does not include octets that were part of frames that were receive… |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.6 | ColumnolEnetStatsPortMcastRcvdOks | read-only | mandatory | The count of the number of multicast frames successfully received by this port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.7 | ColumnolEnetStatsPortBcastRcvdOks | read-only | mandatory | The count of the number of broadcast frames successfully received by this port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.8 | ColumnolEnetStatsPortFrameTooLongs | read-only | mandatory | The count of the number of frames received by this port that exceeds the maximum permitted Ethernet (802.3) frame size. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.9 | ColumnolEnetStatsPortAlignmentErrors | read-only | mandatory | The count of the number of frames received by this port that did not pass the frame check sequence (FCS) check and that are not an integral number of octets. T… |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.10 | ColumnolEnetStatsPortFCSErrors | read-only | mandatory | The count of the number of frames received by this port that did not pass the frame check sequence (FCS) check and are an integral number of octets. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.11 | ColumnolEnetStatsPortRunts | read-only | mandatory | The count of the number of frames received by this port that are less than 512 bits long. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.12 | ColumnolEnetStatsPortSrcAddrChanges | read-only | mandatory | The count of the number of times that olEnetStatsPortLastSourceAddr { olEnetStatsPortEntry 11 } has changed. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.13 | ColumnolEnetStatsPortLastSrcAddr | read-only | mandatory | The last source address seen on this port for this network for the last successfully received frame. |
| 1.3.6.1.4.1.49.2.3.1.5.2.3.1.14 | ColumnolEnetStatsPortLastErrAddr | read-only | mandatory | The value stored in the source address portion of a frame received in error (alignment, FCS, or too long). Since the frame was received in error, there is no g… |
| 1.3.6.1.4.1.49.2.3.1.5.2.4 | TableolEnetMapTable | not-accessible | mandatory | A table that contains a cache of information relating an Ethernet source address with a specific port for a given network. An indication of this source's utili… |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1 | RowolEnetMapEntry | not-accessible | mandatory | A list of information that tracks a source address to a specific port for each network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.1 | ColumnolEnetMapNetID | read-only | mandatory | The network index that uniquely identifies this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.2 | ColumnolEnetMapAddress | read-only | mandatory | An Ethernet source address received by this port on this network. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.3 | ColumnolEnetMapSlotIndex | read-only | mandatory | The slot number of the port that received this address. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.4 | ColumnolEnetMapPortIndex | read-only | mandatory | The port number within olEnetMapSlotIndex's slot that received this address. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.5 | ColumnolEnetMapFrames | read-only | mandatory | An estimated count of the number of frames generated by this address. This count should be interpreted as an indicator, not a true frame count. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.6 | ColumnolEnetMapOctets | read-only | mandatory | An estimated count of the number of octets generated by this address. This count should be interpreted as an indicator, not a true octet count. |
| 1.3.6.1.4.1.49.2.3.1.5.2.4.1.7 | ColumnolEnetMapTime | read-only | mandatory | The time in in hundredths of a second since this address was last seen. For example, if olEnetMapTime is 500 ticks, then this adddress was seen 5 seconds ago. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5 | NodechipSnmpDot3RptrMgt | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1 | NodechipRptrBasicPackage | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1 | NodechipRptrRptrInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1 | TablechipRptrRptrInfoTable | not-accessible | mandatory | Table of descriptive and status information about the repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1 | RowchipRptrRptrInfoEntry | not-accessible | mandatory | An entry in the table, containing information about a repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.1 | ColumnchipRptrRptrInfoSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrRptrInfoNetID resides. If chipRptrRptrInfoNetID does not identify an… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.2 | ColumnchipRptrRptrInfoNetID | read-only | mandatory | The network index that uniquely identifies this repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.3 | ColumnchipRptrGroupCapacity | read-only | mandatory | The chipRptrGroupCapacity is the number of groups that can be contained within the repeater. Within each managed repeater, the groups are uniquely numbered in … |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.4 | ColumnchipRptrOperStatus | read-only | mandatory | The chipRptrOperStatus object indicates the operational state of the repeater. The chipRptrHealthText object may be consulted for more specific information abo… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.5 | ColumnchipRptrHealthText | read-only | mandatory | The health text object is a text string that provides information relevant to the operational state of the repeater. Agents may use this string to provide deta… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.6 | ColumnchipRptrReset | read-write | mandatory | Setting this object to reset(2) causes a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std]. Setting this object to noReset(1) has no effec… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.7 | ColumnchipRptrNonDisruptTest | read-write | mandatory | Setting this object to selfTest(2) causes the repeater to perform a agent-specific, non- disruptive self-test that has the following characteristics: a) The na… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.1.1.1.8 | ColumnchipRptrTotalPartitionedPorts | read-only | mandatory | This object returns the total number of ports in the repeater whose current state meets all three of the following criteria: chipRptrPortOperStatus does not ha… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2 | NodechipRptrGroupInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1 | TablechipRptrGroupTable | not-accessible | mandatory | Table of descriptive and status information about the groups of ports. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1 | RowchipRptrGroupEntry | not-accessible | mandatory | An entry in the table, containing information about a single group of ports. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.1 | ColumnchipRptrGroupSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrGroupNetID resides. If chipRptrGroupNetID does not identify an isola… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.2 | ColumnchipRptrGroupNetID | read-only | mandatory | The network index that uniquely identifies this group's repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.3 | ColumnchipRptrGroupIndex | read-only | mandatory | This object identifies the group within the repeater for which this entry contains information. This value is never greater than chipRptrGroupCapacity. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.4 | ColumnchipRptrGroupDescr | read-only | mandatory | A textual description of the group. This value should include the full name and version identification of the group's hardware type and indicate how the group … |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.5 | ColumnchipRptrGroupObjectID | read-only | mandatory | The vendor's authoritative identification of the group. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides a straight-forwar… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.6 | ColumnchipRptrGroupOperStatus | read-only | mandatory | An object that indicates the operational status of the group. A status of notPresent(4) indicates that the group is temporarily or permanently physically and/o… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.7 | ColumnchipRptrGroupLastOperStatusChange | read-only | mandatory | An object that contains the value of sysUpTime at the time that the value of the chipRptrGroupOperStatus object for this group last changed. A value of zero in… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.2.1.1.8 | ColumnchipRptrGroupPortCapacity | read-only | mandatory | The chipRptrGroupPortCapacity is the number of ports that can be contained within the group. Valid range is 1-1024. Within each group, the ports are uniquely n… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3 | NodechipRptrPortInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1 | TablechipRptrPortTable | not-accessible | mandatory | Table of descriptive and status information about the ports. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1 | RowchipRptrPortEntry | not-accessible | mandatory | An entry in the table, containing information about a single port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.1 | ColumnchipRptrPortSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrPortNetID resides. If chipRptrPortNetID does not identify an isolate… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.2 | ColumnchipRptrPortNetID | read-only | mandatory | The network index that uniquely identifies this port's repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.3 | ColumnchipRptrPortGroupIndex | read-only | mandatory | This object identifies the group containing the port for which this entry contains information. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.4 | ColumnchipRptrPortIndex | read-only | mandatory | This object identifies the port within the group for which this entry contains information. This value can never be greater than chipRptrGroupPortCapacity for … |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.5 | ColumnchipRptrPortAdminStatus | read-write | mandatory | Setting this object to disabled(2) disables the port. A disabled port neither transmits nor receives. Once disabled, a port must be explicitly enabled to resto… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.6 | ColumnchipRptrPortAutoPartitionState | read-only | mandatory | The autoPartitionState flag indicates whether the port is currently partitioned by the repeater's auto-partition protection. The conditions that cause port par… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.1.3.1.1.7 | ColumnchipRptrPortOperStatus | read-only | mandatory | This object indicates the port's operational status. The notPresent(3) status indicates the port is physically removed (note this may or may not be possible de… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2 | NodechipRptrMonitorPackage | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.1 | NodechipRptrMonitorRptrInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.1.1 | TablechipRptrMonitorRptrTable | not-accessible | mandatory | Table of performance and error statistics for the Repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.1.1.1 | RowchipRptrMonitorRptrEntry | not-accessible | mandatory | An entry in the table, containing total performance and error statistics for a repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.1.1.1.1 | ColumnchipRptrMonitorSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrMonitorNetID resides. If chipRptrMonitorNetID does not identify an i… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.1.1.1.2 | ColumnchipRptrMonitorNetID | read-only | mandatory | The network index that uniquely identifies this repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.1.1.1.3 | ColumnchipRptrMonitorTransmitCollisions | read-only | mandatory | This counter is incremented every time the repeater state machine enters the TRANSMIT COLLISION state from any state other than ONE PORT LEFT (Ref: Fig 9-2, IE… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2 | NodechipRptrMonitorGroupInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1 | TablechipRptrMonitorGroupTable | not-accessible | mandatory | Table of performance and error statistics for the groups. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1 | RowchipRptrMonitorGroupEntry | not-accessible | mandatory | An entry in the table, containing total performance and error statistics for a single group. Regular retrieval of the information in this table provides a mean… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1.1 | ColumnchipRptrMonitorGroupSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrMonitorGroupNetID resides. If chipRptrMonitorGroupNetID does not ide… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1.2 | ColumnchipRptrMonitorGroupNetID | read-only | mandatory | The network index that uniquely identifies this group's repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1.3 | ColumnchipRptrMonitorGroupIndex | read-only | mandatory | This object identifies the group within the repeater for which this entry contains information. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1.4 | ColumnchipRptrMonitorGroupTotalFrames | read-only | mandatory | The total number of frames of valid frame length that have been received on the ports in this group. This counter is the summation of the values of the chipRpt… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1.5 | ColumnchipRptrMonitorGroupTotalOctets | read-only | mandatory | The total number of octets contained in the valid frames that have been received on the ports in this group. This counter is the summation of the values of the… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.2.1.1.6 | ColumnchipRptrMonitorGroupTotalErrors | read-only | mandatory | The total number of errors which have occurred on all of the ports in this group. This counter is the summation of the values of the chipRptrMonitorPortTotalEr… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3 | NodechipRptrMonitorPortInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1 | TablechipRptrMonitorPortTable | not-accessible | mandatory | Table of performance and error statistics for the ports. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1 | RowchipRptrMonitorPortEntry | not-accessible | mandatory | An entry in the table, containing performance and error statistics for a single port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.1 | ColumnchipRptrMonitorPortSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrMonitorPortNetID resides. If chipRptrMonitorPortNetID does not ident… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.2 | ColumnchipRptrMonitorPortNetID | read-only | mandatory | The network index that uniquely identifies this port's repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.3 | ColumnchipRptrMonitorPortGroupIndex | read-only | mandatory | This object identifies the group containing the port for which this entry contains information. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.4 | ColumnchipRptrMonitorPortIndex | read-only | mandatory | This object identifies the port within the group for which this entry contains information. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.5 | ColumnchipRptrMonitorPortReadableFrames | read-only | mandatory | This object is the number of frames of valid frame length that have been received on this port. This counter is incremented by one for each frame received on t… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.6 | ColumnchipRptrMonitorPortReadableOctets | read-only | mandatory | This object is the number of octets contained in valid frames that have been received on this port. This counter is incremented by OctetCount for each frame re… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.7 | ColumnchipRptrMonitorPortFCSErrors | read-only | mandatory | This counter is incremented by one for each frame received on this port with the FCSError signal asserted and the FramingError and CollisionEvent signals deass… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.8 | ColumnchipRptrMonitorPortAlignmentErrors | read-only | mandatory | This counter is incremented by one for each frame received on this port with the FCSError and FramingError signals asserted and CollisionEvent signal deasserte… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.9 | ColumnchipRptrMonitorPortFrameTooLongs | read-only | mandatory | This counter is incremented by one for each frame received on this port whose OctetCount is greater than maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). If chipRp… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.10 | ColumnchipRptrMonitorPortShortEvents | read-only | mandatory | This counter is incremented by one for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime. ShortEventMaxTime is greater than 74 b… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.11 | ColumnchipRptrMonitorPortRunts | read-only | mandatory | This counter is incremented by one for each CarrierEvent on this port that meets one of the following two conditions. Only one test need be made. a) The Activi… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.12 | ColumnchipRptrMonitorPortCollisions | read-only | mandatory | This counter is incremented by one for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is asserted. The approximate minimu… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.13 | ColumnchipRptrMonitorPortLateEvents | read-only | mandatory | This counter is incremented by one for each CarrierEvent on this port in which the CollIn(X) variable transitions to the value SQE (Ref: 9.6.6.2, IEEE 802.3 St… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.14 | ColumnchipRptrMonitorPortVeryLongEvents | read-only | mandatory | This counter is incremented by one for each CarrierEvent on this port whose ActivityDuration is greater than the MAU Jabber Lockup Protection timer TW3 (Ref: 9… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.15 | ColumnchipRptrMonitorPortDataRateMismatches | read-only | mandatory | This counter is incremented by one for each frame received on this port that meets all of the following conditions: a) The CollisionEvent signal is not asserte… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.16 | ColumnchipRptrMonitorPortAutoPartitions | read-only | mandatory | This counter is incremented by one for each time the repeater has automatically partitioned this port. The conditions that cause port partitioning are specifie… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.2.3.1.1.17 | ColumnchipRptrMonitorPortTotalErrors | read-only | mandatory | The total number of errors which have occurred on this port. This counter is the summation of the values of other error counters (for the same port), namely: c… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3 | NodechipRptrAddrTrackPackage | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.1 | NodechipRptrAddrTrackRptrInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.2 | NodechipRptrAddrTrackGroupInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3 | NodechipRptrAddrTrackPortInfo | |||
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1 | TablechipRptrAddrTrackTable | not-accessible | mandatory | Table of address mapping information about the ports. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1 | RowchipRptrAddrTrackEntry | not-accessible | mandatory | An entry in the table, containing address mapping information about a single port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.1 | ColumnchipRptrAddrTrackSlotIndex | read-only | mandatory | The slot number of the repeater module on which the isolated network identified by chipRptrMonitorGroupNetID resides. If chipRptrMonitorGroupNetID does not ide… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.2 | ColumnchipRptrAddrTrackGroupNetID | read-only | mandatory | The network index that uniquely identifies this port's repeater. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.3 | ColumnchipRptrAddrTrackGroupIndex | read-only | mandatory | This object identifies the group containing the port for which this entry contains information. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.4 | ColumnchipRptrAddrTrackPortIndex | read-only | mandatory | This object identifies the port within the group for which this entry contains information. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.5 | ColumnchipRptrAddrTrackLastSourceAddress | read-only | mandatory | This object is the SourceAddress of the last readable frame (i.e., counted by chipRptrMonitorPortReadableFrames) received by this port. |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.6 | ColumnchipRptrAddrTrackSourceAddrChanges | read-only | mandatory | This counter is incremented by one for each time that the chipRptrAddrTrackLastSourceAddress attribute for this port has changed. This may indicate whether a l… |
| 1.3.6.1.4.1.49.2.3.1.5.2.5.3.3.1.1.7 | ColumnchipRptrAddrTrackNewLastSrcAddress | read-only | mandatory | This object is the SourceAddress of the last readable frame (i.e., counted by chipRptrMonitorPortReadableFrames) received by this port. If no frames have been … |
| 1.3.6.1.4.1.49.2.3.1.5.3 | NodeolTRnet | |||
| 1.3.6.1.4.1.49.2.3.1.5.3.1 | ScalarolTRnetMapState | read-only | mandatory | The state of the inter-module token ring map. If the map is being updated, then the state of the map is changing. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2 | TableolTRnetStatsTable | not-accessible | mandatory | A list of Token Ring statistics entries counted for each network. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1 | RowolTRnetStatsEntry | not-accessible | mandatory | A collection of statistics kept for a particular Token Ring interface. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.1 | ColumnolTRnetStatsNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.2 | ColumnolTRnetStatsLineErrors | read-only | mandatory | The total number of line errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.3 | ColumnolTRnetStatsBurstErrors | read-only | mandatory | The total number of burst errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.4 | ColumnolTRnetStatsACErrors | read-only | mandatory | The total number of AC (Address Copied) errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.5 | ColumnolTRnetStatsLostFrameErrors | read-only | mandatory | The total number of lost frame errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.6 | ColumnolTRnetStatsCongestionErrors | read-only | mandatory | The total number of receive congestion errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.7 | ColumnolTRnetStatsFrameCopiedErrors | read-only | mandatory | The total number of frame copied errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.8 | ColumnolTRnetStatsTokenErrors | read-only | mandatory | The total number of token errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.9 | ColumnolTRnetStatsDuplicateAddresses | read-only | mandatory | The total number of token errors reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.10 | ColumnolTRnetStatsBeaconEvents | read-only | mandatory | The total number of times that the ring enters the beaconing state. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.11 | ColumnolTRnetStatsLastBeaconSender | read-only | mandatory | The address of the sender of the last beacon frame received on this ring. If no beacon frames have been received, this object will be six zero octets. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.12 | ColumnolTRnetStatsLastBeaconNAUN | read-only | mandatory | The address of the NAUN in the last beacon frame received on this ring. If no beacon frames have been received, this object will be six zero octets. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.13 | ColumnolTRnetStatsLastBeaconTime | read-only | mandatory | The time in in hundredths of a second since the last beacon event occurred. For example, if the time is 500 ticks, then this event was seen 5 seconds ago. If n… |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.14 | ColumnolTRnetStatsLastBeaconAction | read-only | mandatory | The action (if any) taken to correct the last beacon event on the ring. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.15 | ColumnolTRnetStatsTotalStations | read-only | mandatory | The number of stations currently participating in the 802.5 MAC protocol on the ring. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.16 | ColumnolTRnetStatsConcStations | read-only | mandatory | The number of stations currently participating in the 802.5 MAC protocol on the ring which are connected to ports in this concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.17 | ColumnolTRnetStatsTotalPorts | read-only | mandatory | The total number of ports within this concentrator and on this ring regardless of their admin state or status. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.18 | ColumnolTRnetStatsEnabledPorts | read-only | mandatory | The number of ports within this concentrator and on this ring which have olPortAdminState set to enabled. |
| 1.3.6.1.4.1.49.2.3.1.5.3.2.1.19 | ColumnolTRnetStatsActivePorts | read-only | mandatory | The number of ports within this concentrator and on this ring which have olPortAdminState set to enabled and whose olPortStatus has a status of okay. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3 | TableolTRnetStatsStationTable | not-accessible | mandatory | A list of ring statistics entries. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1 | RowolTRnetStatsStationEntry | not-accessible | mandatory | A collection of statistics for a particular station that has been discovered on a a ring monitored by this device. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.1 | ColumnolTRnetStatsStationNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.2 | ColumnolTRnetStatsStationAddr | read-only | mandatory | The physical address of this station. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.3 | ColumnolTRnetStatsStationSlotIndex | read-only | mandatory | The slot number of the station with this address. Addresses with a slot value of external(255) are not in this concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.4 | ColumnolTRnetStatsStationPortIndex | read-only | mandatory | The port number within olTRnetStatsStationSlotIndex's slot that received this address. If olTRnetStatsStationSlotIndex has a value of external(255), then the p… |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.5 | ColumnolTRnetStatsStationNAUNAddress | read-only | mandatory | The physical address of the nearest active upstream neighbor of this station. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.6 | ColumnolTRnetStatsStationLineErrors | read-only | mandatory | The total number of Line Errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.7 | ColumnolTRnetStatsStationBurstErrors | read-only | mandatory | The total number of burst errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.8 | ColumnolTRnetStatsStationACErrors | read-only | mandatory | The total number of AC (Address Copied) errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.9 | ColumnolTRnetStatsStationLostFrameErrors | read-only | mandatory | The total number of lost frame errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.10 | ColumnolTRnetStatsStationCongestionErrors | read-only | mandatory | The total number of congestion errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.11 | ColumnolTRnetStatsStationFrameCopiedErrors | read-only | mandatory | The total number of frame copied errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.12 | ColumnolTRnetStatsStationTokenErrors | read-only | mandatory | The total number of token errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.3.1.13 | ColumnolTRnetStatsStationDuplicateAddresses | read-only | mandatory | The number of times this station experienced a duplicate address error. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4 | TableolTRnetStatsPortTable | not-accessible | mandatory | A list of statistic entries, for ports within the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1 | RowolTRnetStatsPortEntry | not-accessible | mandatory | A collection of statistics for a particular station that has been discovered on a a ring monitored by this device. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.1 | ColumnolTRnetStatsPortSlotIndex | read-only | mandatory | The port slot number. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.2 | ColumnolTRnetStatsPortIndex | read-only | mandatory | The port number within olTRnetStatsPortSlotIndex's slot. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.3 | ColumnolTRnetStatsPortNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.4 | ColumnolTRnetStatsPortTotalStations | read-only | mandatory | The total number of stations attached to this port. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.5 | ColumnolTRnetStatsPortAddress | read-only | mandatory | The mac address of the station connected to this If there are multiple mac addresses for this port, then this object will contain the last mac address. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.6 | ColumnolTRnetStatsPortLineErrors | read-only | mandatory | The total number of Line Errors pertaining to this port reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.7 | ColumnolTRnetStatsPortBurstErrors | read-only | mandatory | The total number of burst errors pertaining to this port reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.8 | ColumnolTRnetStatsPortACErrors | read-only | mandatory | The total number of AC (Address Copied) errors pertaining to this port reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.9 | ColumnolTRnetStatsPortLostFrameErrors | read-only | mandatory | The total number of lost frame errors pertaining to this port reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.10 | ColumnolTRnetStatsPortCongestionErrors | read-only | mandatory | The total number of congestion errors pertaining to this port reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.11 | ColumnolTRnetStatsPortFrameCopiedErrors | read-only | mandatory | The total number of frame copied errors pertaining to this port reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.12 | ColumnolTRnetStatsPortTokenErrors | read-only | mandatory | The total number of token errors pertaining to this station reported in error reporting packets detected by the TRMM. |
| 1.3.6.1.4.1.49.2.3.1.5.3.4.1.13 | ColumnolTRnetStatsPortDuplicateAddresses | read-only | mandatory | The number of times this port experienced a duplicate address error. |
| 1.3.6.1.4.1.49.2.3.1.5.3.5 | NodeolTRnetMapSummary | |||
| 1.3.6.1.4.1.49.2.3.1.5.3.5.1 | ScalarolTRnetMapSummaryLogicalState | read-only | mandatory | The state of the token ring summary table. If the summary is being updated, then the state of the summary is changing. |
| 1.3.6.1.4.1.49.2.3.1.5.3.5.2 | ScalarolTRnetMapSummaryLogicalLock | read-write | mandatory | A semaphore for locking the token ring summary table. When locked, updates to the summary will pend until the semaphore is unlocked, so that a valid summary ca… |
| 1.3.6.1.4.1.49.2.3.1.5.3.5.3 | TableolTRnetMapSummaryTable | not-accessible | mandatory | A logical map of the token ring network, starting from the agent's specified token ring interface. Each station on the map is represented by it's MAC address, … |
| 1.3.6.1.4.1.49.2.3.1.5.3.5.3.1 | RowolTRnetMapSummaryEntry | not-accessible | mandatory | A group of MAC addresses associated with a Token Ring map. |
| 1.3.6.1.4.1.49.2.3.1.5.3.5.3.1.1 | ColumnolTRnetMapSummaryNetID | read-only | mandatory | The network index that uniquely identifies this network. It can be isolated from the backplane, or on one of seven possible backplane token ring networks. |
| 1.3.6.1.4.1.49.2.3.1.5.3.5.3.1.2 | ColumnolTRnetMapSummaryIndex | read-only | mandatory | The index into the map array. Possible values are 1 through 8. The MAC address of this agent is the first MAC address in olTRnetMapSummary32Stations indexed by… |
| 1.3.6.1.4.1.49.2.3.1.5.3.5.3.1.3 | ColumnolTRnetMapSummary32Stations | read-only | mandatory | A concatonated group of MAC addresses and their associated slot and port of stations on the ring. Each entry has the eight octets. The first six octets are the… |
| 1.3.6.1.4.1.49.2.3.1.5.3.6 | TableolTRTrafTable | not-accessible | mandatory | A list of Token Ring network traffic (non-error) statistics entries. Note that all of the frame and octet counters in this table include error frames that have… |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1 | RowolTRTrafEntry | not-accessible | mandatory | A collection of statistics kept for a particular Token Ring interface. Note that all of the frame and octet counters in this table include error frames that ha… |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.1 | ColumnolTRTrafNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.2 | ColumnolTRTrafTokenRotationTime | read-only | mandatory | An estimate of the time (in microseconds) that it takes for the token to complete a single rotation around the ring. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.3 | ColumnolTRTrafDropEvents | read-only | mandatory | The total number of events in which frames were dropped by the TRMM due to lack of resources. Note that this number is not necessarily the number of frames dro… |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.4 | ColumnolTRTrafOctets | read-only | mandatory | The total number of octets of data received on the network. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.5 | ColumnolTRTrafFrames | read-only | mandatory | The total number of frames received. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.6 | ColumnolTRTrafMacOctets | read-only | mandatory | The total number of octets of data in MAC frames received on the network. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.7 | ColumnolTRTrafMacFrames | read-only | mandatory | The total number of MAC frames received. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.8 | ColumnolTRTrafBroadcastFrames | read-only | mandatory | The total number of non-MAC frames received that were directed to a broadcast address (0xFFFFFFFFFFFF or 0xC000FFFFFFFF). |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.9 | ColumnolTRTrafMulticastFrames | read-only | mandatory | The total number of non-MAC frames received that were directed to a local or global multicast or functional address. Note that this number does not include fra… |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.10 | ColumnolTRTrafFrames18to63Octets | read-only | mandatory | The total number of non-MAC frames received that were between 18 and 63 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.11 | ColumnolTRTrafFrames64to127Octets | read-only | mandatory | The total number of non-MAC frames received that were between 64 and 127 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.12 | ColumnolTRTrafFrames128to255Octets | read-only | mandatory | The total number of non-MAC frames received that were between 128 and 255 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.13 | ColumnolTRTrafFrames256to511Octets | read-only | mandatory | The total number of non-MAC frames received that were between 256 and 511 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.14 | ColumnolTRTrafFrames512to1023Octets | read-only | mandatory | The total number of non-MAC frames received that were between 512 and 1023 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.15 | ColumnolTRTrafFrames1024to2047Octets | read-only | mandatory | The total number of non-MAC frames received that were between 1024 and 2047 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.16 | ColumnolTRTrafFrames2048to4095Octets | read-only | mandatory | The total number of non-MAC frames received that were between 2048 and 4095 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.17 | ColumnolTRTrafFrames4096to8191Octets | read-only | mandatory | The total number of non-MAC frames received that were between 4096 and 8191 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.18 | ColumnolTRTrafFrames8192to18000Octets | read-only | mandatory | The total number of non-MAC frames received that were between 8192 and 18000 octets in length inclusive. |
| 1.3.6.1.4.1.49.2.3.1.5.3.6.1.19 | ColumnolTRTrafFramesGreaterThan18000Octets | read-only | mandatory | The total number of non-MAC frames received that were greater than or equal to 18000 octets in length. |
| 1.3.6.1.4.1.49.2.3.1.5.3.7 | TableolTRTrafControlTable | not-accessible | mandatory | A list entries containing information about olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1 | RowolTRTrafControlEntry | not-accessible | mandatory | A collection of information about olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.1 | ColumnolTRTrafControlNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.2 | ColumnolTRTrafControlLogicalState | read-only | mandatory | The state of the token ring station traffic tables: olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable and olTRTrafTopNSummaryTable. If any of the tabl… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.3 | ColumnolTRTrafControlLogicalLock | read-write | mandatory | A semaphore for locking the token ring station traffic tables: olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable. When t… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.4 | ColumnolTRTrafControlClear | read-write | mandatory | When the value of this object is set to clear, all entries in the token ring station traffic tables (olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.5 | ColumnolTRTrafControlLastClearTime | read-only | mandatory | The value of sysUpTime when the token ring station traffic tables (olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable and olTRTrafTopNSummaryTable) wer… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.6 | ColumnolTRTrafControlTotalStations | read-only | mandatory | The number of stations in the portion of the olTRTrafStationTable associated with this olTRTrafControlEntry. |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.7 | ColumnolTRTrafControlStationLastChangeTime | read-only | mandatory | The value of sysUpTime when the last entry was added to or deleted (or re-sorted) from the portion of the olTRTrafStationTable associated with this olTRTrafCon… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.8 | ColumnolTRTrafControlPortTotalStations | read-only | mandatory | The number of stations in the portion of the olTRTrafPortTable associated with this olTRTrafControlEntry. |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.9 | ColumnolTRTrafControlPortLastChangeTime | read-only | mandatory | The value of sysUpTime when the last entry was added to or deleted (or re-sorted) from the portion of the olTRTrafPortTable associated with this olTRTrafContro… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.10 | ColumnolTRTrafControlTopNMaxStations | read-write | mandatory | Specifies a maximum value for olTRTrafControlTopNTotalStations in this olTRTrafControlEntry. If this value is zero then no maximum value for olTRTrafControlTop… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.11 | ColumnolTRTrafControlTopNTotalStations | read-only | mandatory | The number of stations (for each statistic) in the portion of the olTRTrafTopNTable and olTRTrafTopNSummaryTable associated with this olTRTrafControlEntry. If … |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.12 | ColumnolTRTrafControlTopNLastChangeTime | read-only | mandatory | The value of sysUpTime when the last entry was added to or deleted (or re-sorted) from the portion of the olTRTrafTopNTable and olTRTrafTopNSummaryTable associ… |
| 1.3.6.1.4.1.49.2.3.1.5.3.7.1.13 | ColumnolTRTrafControlTopNInterval | read-write | mandatory | Specifies the length of the TopN data collection period in seconds. Minimum length is 5 seconds; maximum is 86400 seconds (24 hours). When this value is modifi… |
| 1.3.6.1.4.1.49.2.3.1.5.3.8 | TableolTRTrafStationTable | not-accessible | mandatory | A list of Token Ring station traffic statistics entries indexed by Network ID and MAC address. The table has olTRTrafTotalStations entries. Note that all of th… |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1 | RowolTRTrafStationEntry | not-accessible | mandatory | A collection of station statistics for a particular station that has been discovered on an interface of this device. Note that all of the frame and octet count… |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.1 | ColumnolTRTrafStationNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.2 | ColumnolTRTrafStationAddress | read-only | mandatory | The physical address of this station. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.3 | ColumnolTRTrafStationSlotIndex | read-only | mandatory | The slot number of the station with this address. Addresses with a slot value of remote-ring(254) are not in this ring. Addresses with a slot value of external… |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.4 | ColumnolTRTrafStationPortIndex | read-only | mandatory | The port number within olTRTrafSlotIndex's slot that received this address. If olTRTrafSlotIndex has a value of remote-ring(254), then the port address will be… |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.5 | ColumnolTRTrafStationInFrames | read-only | mandatory | The number of frames transmitted to this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.6 | ColumnolTRTrafStationOutFrames | read-only | mandatory | The number of frames transmitted by this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.7 | ColumnolTRTrafStationInOctets | read-only | mandatory | The number of octets transmitted to this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.8 | ColumnolTRTrafStationOutOctets | read-only | mandatory | The number of octets transmitted by this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.9 | ColumnolTRTrafStationOutErrors | read-only | mandatory | The number of error frames transmitted by this address since it was added to this table. Only isolating errors (LineErrors, BurstErrors, ACErrors, InternalErro… |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.10 | ColumnolTRTrafStationOutBroadcastFrames | read-only | mandatory | The number of frames transmitted by this address that were directed to the broadcast address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.8.1.11 | ColumnolTRTrafStationOutMulticastFrames | read-only | mandatory | The number of frames transmitted by this address that were directed to a multicast address since it was added to this table. Note that this number does not inc… |
| 1.3.6.1.4.1.49.2.3.1.5.3.9 | TableolTRTrafPortTable | not-accessible | mandatory | A list of Token Ring station traffic statistics entries indexed by slot number, and port number. Note that stations external to this concentrator or on another… |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1 | RowolTRTrafPortEntry | not-accessible | mandatory | A collection of station statistics for a particular station that has been discovered on an interface of this device. Note that all of the frame and octet count… |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.1 | ColumnolTRTrafPortSlotIndex | read-only | mandatory | The slot number of the station with this address. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.2 | ColumnolTRTrafPortPortIndex | read-only | mandatory | The port number within olTRTrafPortSlotIndex's slot that received this address. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.3 | ColumnolTRTrafPortNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.4 | ColumnolTRTrafPortAddress | read-only | mandatory | The physical address of this station. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.5 | ColumnolTRTrafPortInFrames | read-only | mandatory | The number of frames transmitted to this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.6 | ColumnolTRTrafPortOutFrames | read-only | mandatory | The number of frames transmitted by this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.7 | ColumnolTRTrafPortInOctets | read-only | mandatory | The number of octets transmitted to this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.8 | ColumnolTRTrafPortOutOctets | read-only | mandatory | The number of octets transmitted by this address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.9 | ColumnolTRTrafPortOutErrors | read-only | mandatory | The number of error frames transmitted by this address since it was added to this table. Only isolating errors (LineErrors, BurstErrors, ACErrors, InternalErro… |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.10 | ColumnolTRTrafPortOutBroadcastFrames | read-only | mandatory | The number of frames transmitted by this address that were directed to the broadcast address since it was added to this table. |
| 1.3.6.1.4.1.49.2.3.1.5.3.9.1.11 | ColumnolTRTrafPortOutMulticastFrames | read-only | mandatory | The number of frames transmitted by this address that were directed to a multicast address since it was added to this table. Note that this number does not inc… |
| 1.3.6.1.4.1.49.2.3.1.5.3.10 | TableolTRTrafTopNTable | not-accessible | mandatory | A list of Token Ring station traffic statistics entries indexed by olTRTrafTopNNetID, olTRTrafTopNStatistic, and olTRTrafTopNIndex. For each Network, the list … |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1 | RowolTRTrafTopNEntry | not-accessible | mandatory | A collection of station statistics for a particular station that has been discovered on an interface of this device. Note that all of the frame and octet count… |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.1 | ColumnolTRTrafTopNNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.2 | ColumnolTRTrafTopNStatistic | read-only | mandatory | The object representing the statistic for each station that this portion of the olTRTrafTopNTable is sorted on. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.3 | ColumnolTRTrafTopNIndex | read-only | mandatory | An index that uniquely identifies an entry in the olTRTrafTopN table among those in the same network and for the same olTRTrafTopNStatistic. This index is betw… |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.4 | ColumnolTRTrafTopNAddress | read-only | mandatory | The physical address of this station. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.5 | ColumnolTRTrafTopNSlotIndex | read-only | mandatory | The slot number of the station with this address. Addresses with a slot value of remote-ring(254) are not in this ring. Addresses with a slot value of external… |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.6 | ColumnolTRTrafTopNPortIndex | read-only | mandatory | The port number within olTRTrafTopNSlotIndex's slot that received this address. If olTRTrafTopNSlotIndex has a value of remote-ring(254), then the port address… |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.7 | ColumnolTRTrafTopNInFrames | read-only | mandatory | The number of frames transmitted to this address during the last TopN data collection period. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.8 | ColumnolTRTrafTopNOutFrames | read-only | mandatory | The number of frames transmitted by this address during the last TopN data collection period. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.9 | ColumnolTRTrafTopNInOctets | read-only | mandatory | The number of octets transmitted to this address during the last TopN data collection period. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.10 | ColumnolTRTrafTopNOutOctets | read-only | mandatory | The number of octets transmitted by this address during the last TopN data collection period. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.11 | ColumnolTRTrafTopNOutErrors | read-only | mandatory | The number of error frames transmitted by this address during the last TopN data collection period. Only isolating errors (LineErrors, BurstErrors, ACErrors, I… |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.12 | ColumnolTRTrafTopNOutBroadcastFrames | read-only | mandatory | The number of frames transmitted by this address that were directed to the broadcast address during the last TopN data collection period. |
| 1.3.6.1.4.1.49.2.3.1.5.3.10.1.13 | ColumnolTRTrafTopNOutMulticastFrames | read-only | mandatory | The number of frames transmitted by this address that were directed to a multicast address during the last TopN data collection period. Note that this number d… |
| 1.3.6.1.4.1.49.2.3.1.5.3.11 | TableolTRTrafTopNSummaryTable | not-accessible | mandatory | A list containing information from olTRTrafTopNTable provided for the convenience of network management stations that wish to obtain this information in conden… |
| 1.3.6.1.4.1.49.2.3.1.5.3.11.1 | RowolTRTrafTopNSummaryEntry | not-accessible | mandatory | A segment of the Top N list for a particular statistic. |
| 1.3.6.1.4.1.49.2.3.1.5.3.11.1.1 | ColumnolTRTrafTopNSummaryNetID | read-only | mandatory | The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated. |
| 1.3.6.1.4.1.49.2.3.1.5.3.11.1.2 | ColumnolTRTrafTopNSummaryStatistic | read-only | mandatory | The object representing the statistic for each station that this portion of the olTRTrafTopNSummaryTable is sorted on. |
| 1.3.6.1.4.1.49.2.3.1.5.3.11.1.3 | ColumnolTRTrafTopNSummaryIndex | read-only | mandatory | An index that uniquely identifies an entry in the olTRTrafTopNSummary table among those in the same network and for the same olTRTrafTopNSummaryStatistic. The … |
| 1.3.6.1.4.1.49.2.3.1.5.3.11.1.4 | ColumnolTRTrafTopNSummaryStations | read-only | mandatory | A concatonated list of (up to 12) MAC addresses, their associated slot and port, and a statistic value for traffic associated with stations on the ring. Each e… |
| 1.3.6.1.4.1.49.2.3.1.5.4 | NodeolFDDInet | |||
| 1.3.6.1.4.1.49.2.3.1.5.4.2 | TableolFDDIStatsModTable | not-accessible | mandatory | A table of statistical information counted for each module in each FDDI network. |
| 1.3.6.1.4.1.49.2.3.1.5.4.2.1 | RowolFDDIStatsModEntry | not-accessible | mandatory | A list of statistical information for each module on each FDDI network in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.4.2.1.1 | ColumnolFDDIStatsModSlotIndex | read-only | mandatory | The slot number that contains this module. |
| 1.3.6.1.4.1.49.2.3.1.5.4.2.1.2 | ColumnolFDDIStatsModMgtRcvErrs | read-only | mandatory | The number of errors encountered while receiving data on the Management Channel. |
| 1.3.6.1.4.1.49.2.3.1.5.4.2.1.3 | ColumnolFDDIStatsModMgtXmitErrs | read-only | mandatory | The number of errors encountered while transmitting data on the Management Channel. |
| 1.3.6.1.4.1.49.2.3.1.5.4.2.1.4 | ColumnolFDDIStatsModBackplaneErrs | read-only | mandatory | The number of errors while receiving and transmitting network data on the backplane. |
| 1.3.6.1.4.1.49.2.3.1.5.4.2.1.5 | ColumnolFDDIStatsModPllUnlockErrs | read-only | mandatory | The number of times the phased lock loop on the backplane network data channel was lost. |
| 1.3.6.1.4.1.49.2.3.1.5.4.3 | TableolFDDIStatsPortTable | not-accessible | mandatory | A table of statistical information counted for each Port in each FDDI network. |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1 | RowolFDDIStatsPortEntry | not-accessible | mandatory | A list of statistical information for each Port on each FDDI network in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1.1 | ColumnolFDDIStatsPortSlotIndex | read-only | mandatory | The slot number that contains this Port. |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1.2 | ColumnolFDDIStatsPortIndex | read-only | mandatory | The Port number of this port |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1.3 | ColumnolFDDIStatsPortLCTFailCts | read-only | mandatory | The count of the consecutive times the link confidence test (LCT) has failed during connection management. Once the connection has been established, the count … |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1.4 | ColumnolFDDIStatsPortLerEstimate | read-only | mandatory | A long term average link error rate. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the exponent of the estimate (the larger the num… |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1.5 | ColumnolFDDIStatsPortLemRejectCts | read-only | mandatory | A link error monitoring count of the times that a link has been removed from the ring due to the LerCutOff threshold being exceeded. |
| 1.3.6.1.4.1.49.2.3.1.5.4.3.1.6 | ColumnolFDDIStatsPortLemCts | read-only | mandatory | The aggregate link error monitor error count, set to zero only on station power up. This variable's long term rate average is lerEstimate. |
| 1.3.6.1.4.1.49.2.3.1.5.4.4 | TableolFDDInetStatsTable | not-accessible | mandatory | A table of statistical information counted for each FDDI network in the concentrator |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1 | RowolFDDInetStatsEntry | not-accessible | mandatory | A list of statistical information for each FDDI network in the concentrator. |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1.1 | ColumnolFDDInetStatsNetID | read-only | mandatory | The network index that uniquely identifies this network. One of isolated, fddi-1, fddi-2, fddi-3, or fddi-4. |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1.2 | ColumnolFDDInetStatsRingOpCounts | read-only | mandatory | The number times the ring transitioned to operational. |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1.3 | ColumnolFDDInetStatsFrameCounts | read-only | mandatory | Frame-Ct (refer to ANSI MAC 2.2.1). |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1.4 | ColumnolFDDInetStatsErrorCounts | read-only | mandatory | Error-Ct (refer to ANSI MAC 2.2.1). |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1.5 | ColumnolFDDInetStatsLostCounts | read-only | mandatory | Lost-Ct (refer to ANSI MAC 2.2.1). |
| 1.3.6.1.4.1.49.2.3.1.5.4.4.1.6 | ColumnolFDDInetStatsFrameErrorRatio | read-only | mandatory | This attribute is the actual ratio, ((delta snmpFddiMACLostCt + delta snmpFddiMACErrorCt) / (delta snmpFddiMACFrameCt + delta snmpFddiMACLostCt)) x 2**16. |
| 1.3.6.1.4.1.49.2.3.1.6 | NodeolGroups | |||
| 1.3.6.1.4.1.49.2.3.1.6.1 | TableolGroupPortTable | not-accessible | mandatory | A list of groups that each port is in. Each port can can be in 0, 1, or many groups. |
| 1.3.6.1.4.1.49.2.3.1.6.1.1 | RowolGroupPortEntry | not-accessible | mandatory | The groups corresponding to a particular port. |
| 1.3.6.1.4.1.49.2.3.1.6.1.1.1 | ColumnolGroupPortSlotIndex | read-only | mandatory | The slot number that contains this port. |
| 1.3.6.1.4.1.49.2.3.1.6.1.1.2 | ColumnolGroupPortIndex | read-only | mandatory | The port number within this slot. Logical ports can not be put into groups. |
| 1.3.6.1.4.1.49.2.3.1.6.1.1.3 | ColumnolGroupPortGroupID | read-only | mandatory | The group(s) to which the port has been assigned. |
| 1.3.6.1.4.1.49.2.3.1.6.2 | TableolGroupSummaryTable | not-accessible | mandatory | A table of condensed group information listing all the ports in each group. |
| 1.3.6.1.4.1.49.2.3.1.6.2.1 | RowolGroupSummaryEntry | not-accessible | mandatory | The summary of all the ports in a particular group. |
| 1.3.6.1.4.1.49.2.3.1.6.2.1.1 | ColumnolGroupSummaryGroupID | read-only | mandatory | The group to which the ports have been assigned. A port can be in one or more groups. |
| 1.3.6.1.4.1.49.2.3.1.6.2.1.2 | ColumnolGroupSummaryIndex | read-only | mandatory | The index into the summary array. Up to 256 ports will be shown in olGroupSummaryPorts for each value in this entry. |
| 1.3.6.1.4.1.49.2.3.1.6.2.1.3 | ColumnolGroupSummaryPorts | read-only | mandatory | A condensed list of all the ports in this group. The summary is in the format: Slotx PortX SlotY PortY ... |
| 1.3.6.1.4.1.49.2.3.1.6.3 | NodeolGroupSet | |||
| 1.3.6.1.4.1.49.2.3.1.6.3.1 | ScalarolGroupSetAction | read-write | mandatory | This object specifies the action that we apply on a group. add-ports(1) adds port(s) to a group, clear-ports(2) clears (delete) port(s) from a group, and set-a… |
| 1.3.6.1.4.1.49.2.3.1.6.3.2 | ScalarolGroupSetGroupID | read-write | mandatory | A group index that uniquely identifies this group. A port can be in zero, one, or more groups. |
| 1.3.6.1.4.1.49.2.3.1.6.3.3 | ScalarolGroupSetSlotIndex | read-write | mandatory | This object specifies the slot number of the port(s) that are to be added/cleared to/from the group. This object should be set whenever add-ports(1) or clear-p… |
| 1.3.6.1.4.1.49.2.3.1.6.3.4 | ScalarolGroupSetPortIndex | read-write | mandatory | This object specifies the port number of the port(s) that are to be added/cleared to/from the group. This object should be set whenever add-ports(1) or clear-p… |
| 1.3.6.1.4.1.49.2.3.1.6.3.5 | ScalarolGroupSetAdminState | read-write | mandatory | This object specifies the Admin State that all the ports in the group defined by olGroupSetGroupID should be set to. This object should be set whenever set-adm… |
| 1.3.6.1.4.1.49.2.3.1.7 | NodeolAlarm | |||
| 1.3.6.1.4.1.49.2.3.1.7.1 | NodeolThresh | |||
| 1.3.6.1.4.1.49.2.3.1.7.1.1 | NodeolThreshControl | |||
| 1.3.6.1.4.1.49.2.3.1.7.1.1.1 | ScalarolThreshTotalEntries | read-only | mandatory | The number of entries currently in olThreshTable. |
| 1.3.6.1.4.1.49.2.3.1.7.1.1.2 | ScalarolThreshMaxEntries | read-only | mandatory | The maximum number of entries in olThreshTable supported by this agent. |
| 1.3.6.1.4.1.49.2.3.1.7.1.1.3 | ScalarolThreshLastCreatedIndex | read-only | mandatory | The index of the last entry in olThreshTable created via index 255 (see olThreshMode). If none, this value will be zero. |
| 1.3.6.1.4.1.49.2.3.1.7.1.1.4 | ScalarolThreshAllMode | read-write | mandatory | Provides the management station with a convenient way to set olThreshMode for all of the entries in ThreshTable. Setting olThreshAllMode to enable(1) or disabl… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2 | TableolThreshTable | not-accessible | mandatory | A list of thresholding entries. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1 | RowolThreshEntry | not-accessible | mandatory | A collection of variables for controlling and monitoring a specific threshold. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.1 | ColumnolThreshIndex | read-only | mandatory | An index that uniquely identifies an entry in the olThresh table. The number of entries in olTRThreshTable is olThreshTotalEntries. A new entry is created when… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.2 | ColumnolThreshMode | read-write | mandatory | The mode for this threshold. enable(1) indicates that this entry is in use and thresholding will be done. disable(2) indicates that this entry is in use but wi… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.3 | ColumnolThreshDescription | read-write | mandatory | Description of the threshold to be sent with the chipAboveThreshd trap. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.4 | ColumnolThreshObjectIdentifier | read-write | mandatory | The object identifier that specifies the statistic to be thresholded. The statistic to be thresholded can be specified either by setting olThreshObjectIdentifi… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.5 | ColumnolThreshStatCategory | read-write | mandatory | Specifies the category of statistic to be thresholded. When olThreshStatCategory is network(2) or station(4), olThreshStatNetID must also be specified and olTh… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.6 | ColumnolThreshStatType | read-write | mandatory | Specifies the type of statistic to be thresholded. error-frames(6) is valid only when olThreshStatCategory is port(3) or station(4). tr-net-soft-errors(7) or t… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.7 | ColumnolThreshStatNetID | read-write | mandatory | When olThreshStatCategory is network(2) or station(4), specifies the network of statistic to be thresholded. If the agent is capable of collecting statistics o… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.8 | ColumnolThreshStatSlotIndex | read-write | mandatory | When olThreshStatCategory is port(3), specifies the slot index of the port of statistic to be thresholded. Note that when this variable is set, olThreshStatNet… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.9 | ColumnolThreshStatPortIndex | read-write | mandatory | When olThreshStatCategory is port(3), specifies the port index of the port of statistic to be thresholded. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.10 | ColumnolThreshStatStationAddr | read-write | mandatory | When olThreshStatCategory is station(4), specifies the MAC address of the station of statistic to be thresholded. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.11 | ColumnolThreshInterval | read-write | mandatory | Specifies the length of the thresholding period in seconds. Minimum length is 5 seconds; maximum is 86400 seconds (24 hours). |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.12 | ColumnolThreshCondition | read-write | mandatory | Specifies the type of conditional comparison for the threshold. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.13 | ColumnolThreshValue | read-write | mandatory | At the end of each thresholding interval (olThreshInterval seconds), olThreshCurrentValue is compared against olThreshValue (unsigned). When olThreshType is de… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.14 | ColumnolThreshCurrentValue | read-only | mandatory | When olThreshType is delta-exceed(1): The most recent delta value of olThreshStatObjectIdentifier (i.e. value of olThreshStatObjectIdentifier at the end of the… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.15 | ColumnolThreshStatus | read-only | mandatory | When olThreshType is delta-exceed(1): If olThreshStatObjectIdentifier has not yet been specified, olThreshStatus will be no-statistic-specified(1). If the firs… |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.16 | ColumnolThreshTimeSinceLastTriggered | read-only | mandatory | Time in TimeTicks that has elapsed since a chipAboveThreshd trap associated with this ThreshEntry was last sent. If never sent, this value shall be zero. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.17 | ColumnolThreshActionType | read-write | mandatory | The action to be performed when the threshold is triggered. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.18 | ColumnolThreshActionData | read-write | mandatory | Additional information to be sent with the chipAboveThreshd trap. In the case of scripts, this object will contain the script number to be executed. |
| 1.3.6.1.4.1.49.2.3.1.7.1.2.1.19 | ColumnolThreshActionPriority | read-write | mandatory | The priority for this entry. Provided for use by the network management station (NMS) - not interpreted by the agent. |
| 1.3.6.1.4.1.49.2.3.1.8 | NodeocPower | |||
| 1.3.6.1.4.1.49.2.3.1.8.1 | NodeocPowerControl | |||
| 1.3.6.1.4.1.49.2.3.1.8.1.1 | ScalarocPowerModeAdminStatus | read-write | mandatory | The current desired state of hub power fault-tolerant mode. Setting this object to fault-tolerant(1) will reserve one power supply's worth of power from the po… |
| 1.3.6.1.4.1.49.2.3.1.8.1.2 | ScalarocPowerModeOperStatus | read-only | mandatory | The current operational status of hub power fault-tolerant mode. |
| 1.3.6.1.4.1.49.2.3.1.8.1.3 | ScalarocPowerOverheatPowerDownMode | read-write | mandatory | The current desired state of hub overheat automatic power- down mode. Setting this object to enable(1) will cause slots containing ONcore modules to be automat… |
| 1.3.6.1.4.1.49.2.3.1.8.2 | TableocPowerOutputTable | not-accessible | mandatory | A table that contains information about the hub power budget. This table is indexed by voltage line type, each of which is supplied by the operational power su… |
| 1.3.6.1.4.1.49.2.3.1.8.2.1 | RowocPowerOutputEntry | not-accessible | mandatory | A list of information about the hub power budget. |
| 1.3.6.1.4.1.49.2.3.1.8.2.1.1 | ColumnocPowerOutputType | read-only | mandatory | Identifies the power (voltage) line type for which this entry contains power budget information. |
| 1.3.6.1.4.1.49.2.3.1.8.2.1.2 | ColumnocPowerOutputVoltageLevel | read-only | mandatory | In millivolts (1/1000 Volt), the actual voltage level for this voltage type as sensed on the backplane. This voltage is supplied by all operational power suppl… |
| 1.3.6.1.4.1.49.2.3.1.8.2.1.3 | ColumnocPowerOutputWattageCapacity | read-only | mandatory | In hundredths of a Watt (1/100 Watt), the maximum wattage for the voltage line that is output by all operational power supplies combined. |
| 1.3.6.1.4.1.49.2.3.1.8.2.1.4 | ColumnocPowerOutputWattageConsumed | read-only | mandatory | In hundredths of a Watt (1/100 Watt), the wattage consumed by all hub modules. For a given voltage line, this object's value is the sum total of the power cons… |
| 1.3.6.1.4.1.49.2.3.1.8.2.1.5 | ColumnocPowerOutputWattageAvailable | read-only | mandatory | In hundredths of a Watt (1/100 Watt), the wattage available to power-up modules. If power fault-tolerant mode is enabled (when it was previously disabled), thi… |
| 1.3.6.1.4.1.49.2.3.1.8.2.1.6 | ColumnocPowerOutputUnmanagedWattageAlloc | read-only | mandatory | In hundredths of a Watt (1/100 Watt), the wattage allocated for modules that are not power-manageable (i.e., ONline modules). |
| 1.3.6.1.4.1.49.2.3.1.8.3 | TableocPowerSlotTable | not-accessible | mandatory | A table that contains power management information for each non-empty, payload slot in the hub. |
| 1.3.6.1.4.1.49.2.3.1.8.3.1 | RowocPowerSlotEntry | not-accessible | mandatory | A list of power management information for each non-empty, payload slot in the hub. |
| 1.3.6.1.4.1.49.2.3.1.8.3.1.1 | ColumnocPowerSlotIndex | read-only | mandatory | The unique slot number that identifies the module associated with this power entry. |
| 1.3.6.1.4.1.49.2.3.1.8.3.1.2 | ColumnocPowerSlotClass | read-write | mandatory | The current slot power class. For a slot containing an ONcore module, this object's value ranges from 1 to 10, where 1 is the lowest power class and 10 is the … |
| 1.3.6.1.4.1.49.2.3.1.8.3.1.3 | ColumnocPowerSlotAdminStatus | read-write | mandatory | The current desired slot power state. For a slot containing an ONcore module, setting this object to enable(1) will cause the module to be power-enabled, provi… |
| 1.3.6.1.4.1.49.2.3.1.8.3.1.4 | ColumnocPowerSlotOperStatus | read-only | mandatory | The current operational slot power status. This object will have the value enabled(1), if the slot contains an ONcore module and is actually power-enabled. Thi… |
| 1.3.6.1.4.1.49.2.3.1.9 | NodeocInventory | |||
| 1.3.6.1.4.1.49.2.3.1.9.1 | NodeocInvHub | |||
| 1.3.6.1.4.1.49.2.3.1.9.1.1 | ScalarocInvHubType | read-only | mandatory | The hub type (i.e. model number) of the hub. An instance for which information is not valid will return 'invalid EEPROM!'. |
| 1.3.6.1.4.1.49.2.3.1.9.1.2 | ScalarocInvHubSerialNo | read-only | mandatory | The serial number of the hub. An instance for which information is not valid will return 'invalid EEPROM!'. |
| 1.3.6.1.4.1.49.2.3.1.9.1.3 | ScalarocInvHubHWVer | read-only | mandatory | The revision number of the hardware of the hub. An instance for which information is not valid will return 'invalid EEPROM!'. |
| 1.3.6.1.4.1.49.2.3.1.9.1.4 | ScalarocInvHubMfr | read-only | mandatory | The company name that manufactured this hub. An instance for which information is not valid will return 'invalid EEPROM!. |
| 1.3.6.1.4.1.49.2.3.1.9.1.5 | ScalarocInvHubMfrDate | read-only | mandatory | The date in yymmdd format that this unit was manufactured. An instance for which information is not valid will return 'invalid EEPROM!'. |
| 1.3.6.1.4.1.49.2.3.1.9.2 | NodeocInvMods | |||
| 1.3.6.1.4.1.49.2.3.1.9.2.1 | TableocInvModTable | not-accessible | mandatory | A list of inventory information related to a module, indexed with respect to slot and subslot location numbers. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1 | RowocInvModEntry | not-accessible | mandatory | Values to describe a module inventory items. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.1 | ColumnocInvModSlotIndex | read-only | mandatory | The slot number where this Module is located. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.2 | ColumnocInvModSubSlotIndex | read-only | mandatory | The subslot number where this Module is located. It is associated with a slot number. Motherboards are always located in subslot one, (e.g. <slot>.1). However,… |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.3 | ColumnocInvModModel | read-only | mandatory | This Module model number. If the instance value is unknown, ONline will be returned. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.4 | ColumnocInvModSerialNo | read-only | mandatory | This Module serial number. If the instance value is unknown, N/A will be returned. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.5 | ColumnocInvModHWVer | read-only | mandatory | The revision number of the hardware on this module. If the instant value is unknown, N/A will be returned. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.6 | ColumnocInvModSWVer | read-only | mandatory | The revision number of the software on this module. If the instant value is unknown, N/A will be returned. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.7 | ColumnocInvModSWBootVer | read-only | mandatory | The revision number of the boot software on this module. If the instant value is unknown, N/A will be returned. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.8 | ColumnocInvModMfr | read-only | mandatory | The company name that manufactured this module. If the instant value is unkonwn, N/A will be returned. |
| 1.3.6.1.4.1.49.2.3.1.9.2.1.1.9 | ColumnocInvModMfrDate | read-only | mandatory | The date in yymmdd format that this module was manufactured. If the instant value is unknown, N/A will be returned. |
| 1.3.6.1.4.1.49.2.3.1.11 | NodeolPS2 | |||
| 1.3.6.1.4.1.49.2.3.1.11.1 | NodeolPS2Info | |||
| 1.3.6.1.4.1.49.2.3.1.11.1.1 | ScalarolPS2OperatingSystem | read-only | mandatory | The type of operating system current including its version and release numbers, currently executing on the PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.1.2 | ScalarolPS2FixedDiskSize | read-only | mandatory | The size in of Fixed Disk Memory currently installed on the PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.1.3 | ScalarolPS2RamSize | read-only | mandatory | The size in of Random Access Memory currently installed on the PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.2 | TableolPS2McaTable | not-accessible | mandatory | A table of software application information associated with the PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.2.1 | RowolPS2McaEntry | not-accessible | mandatory | A profile of a specific software application associated with this PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.2.1.1 | ColumnolPS2McaIndex | read-only | mandatory | The index for this software application. |
| 1.3.6.1.4.1.49.2.3.1.11.2.1.2 | ColumnolPS2McaDescription | read-only | mandatory | A description of the software application. |
| 1.3.6.1.4.1.49.2.3.1.11.2.1.3 | ColumnolPS2McaSlotConnectPoint | read-only | mandatory | The slot number of a module within this ONline chassis to which this Micro channel Adapter Card is connected. If not connected to any ONline module module, the… |
| 1.3.6.1.4.1.49.2.3.1.11.2.1.4 | ColumnolPS2McaPortConnectPoint | read-only | mandatory | The port number of a module within this ONline chassis to which this Micro channel Adapter Card is connected. If not connected to any ONline module module, the… |
| 1.3.6.1.4.1.49.2.3.1.11.2.1.5 | ColumnolPS2McaMacAddress | read-only | mandatory | The MAC Address of the Micro channel adapter card installed this PS/2 Micro channel Adapter Card slot. If no MAC address is defined this string is encoded as a… |
| 1.3.6.1.4.1.49.2.3.1.11.3 | TableolPS2ApplTable | not-accessible | mandatory | A table of software application information associated with the PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.3.1 | RowolPS2ApplEntry | not-accessible | mandatory | A profile of a specific software application associated with this PS/2. |
| 1.3.6.1.4.1.49.2.3.1.11.3.1.1 | ColumnolPS2ApplIndex | read-only | mandatory | The index for this software application. |
| 1.3.6.1.4.1.49.2.3.1.11.3.1.2 | ColumnolPS2ApplDescription | read-only | mandatory | A description of the software application. |
| 1.3.6.1.4.1.49.2.3.2 | Nodeoebm | |||
| 1.3.6.1.4.1.49.2.3.3 | Nodemidnight | |||
| 1.3.6.1.4.1.49.2.3.4 | NodeworkGroupHub | |||
| 1.3.6.1.4.1.49.2.3.4.1 | NodehubSysGroup | |||
| 1.3.6.1.4.1.49.2.3.4.2 | NodehardwareGroup | |||
| 1.3.6.1.4.1.49.2.3.4.3 | NodesoftwareGroup | |||
| 1.3.6.1.4.1.49.2.3.4.4 | NodehubGroup | |||
| 1.3.6.1.4.1.49.2.3.4.5 | NodeboardGroup | |||
| 1.3.6.1.4.1.49.2.3.4.6 | NodeportGroup | |||
| 1.3.6.1.4.1.49.2.3.4.7 | NodealarmGroup | |||
| 1.3.6.1.4.1.49.2.3.5 | Nodeemm | |||
| 1.3.6.1.4.1.49.2.3.6 | NodechipBridge | |||
| 1.3.6.1.4.1.49.2.3.7 | Nodetrmm | |||
| 1.3.6.1.4.1.49.2.3.8 | Nodefmm | |||
| 1.3.6.1.4.1.49.2.3.9 | Nodefocus1 | |||
| 1.3.6.1.4.1.49.2.3.10 | Nodeoeim | |||
| 1.3.6.1.4.1.49.2.3.11 | Nodeoncore | |||
| 1.3.6.1.4.1.49.2.3.12 | Nodedmm | |||
| 1.3.6.1.4.1.49.2.3.13 | NodeonsembleEthernet | |||
| 1.3.6.1.4.1.49.2.4 | NodechipExperiment | |||
| 1.3.6.1.4.1.49.2.4.1 | NodechipExpTokenRing | |||
| 1.3.6.1.4.1.49.2.4.1.1 | NodeexpDot5 | |||
| 1.3.6.1.4.1.49.2.4.1.1.1 | TableexpDot5Table | not-accessible | obsolete | This table contains Token Ring interface parameters and state variables, one entry per 802.5 interface. |
| 1.3.6.1.4.1.49.2.4.1.1.1.1 | RowexpDot5Entry | not-accessible | obsolete | A list of Token Ring status and parameter values for an 802.5 interface. |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.1 | ColumnexpDot5IfIndex | read-only | obsolete | The value of this object identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interfa… |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.2 | ColumnexpDot5Commands | read-write | obsolete | When this object is set to the value of open(2), the station should go into the open state. The progress and success of the open is given by the values of the … |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.3 | ColumnexpDot5RingStatus | read-only | obsolete | The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station has successfully been added to t… |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.4 | ColumnexpDot5RingState | read-only | obsolete | The current interface state with respect to entering or leaving the ring. |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.5 | ColumnexpDot5RingOpenStatus | read-only | obsolete | This object indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring. |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.6 | ColumnexpDot5RingSpeed | read-write | obsolete | The ring's bandwidth. |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.7 | ColumnexpDot5UpStream | read-only | obsolete | The MAC-address of the up stream neighbor station in the ring. |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.8 | ColumnexpDot5ActMonParticipate | read-write | obsolete | If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. … |
| 1.3.6.1.4.1.49.2.4.1.1.1.1.9 | ColumnexpDot5Functional | read-write | obsolete | The bit mask of all Token Ring functional addresses for which this interface will accept frames. |
| 1.3.6.1.4.1.49.2.4.1.1.2 | TableexpDot5StatsTable | not-accessible | obsolete | A table containing Token Ring statistics, one entry per 802.5 interface. All the statistics are defined using the syntax Counter as 32-bit wrap around counters… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1 | RowexpDot5StatsEntry | not-accessible | obsolete | An entry contains the 802.5 statistics for a particular interface. |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.1 | ColumnexpDot5StatsIfIndex | read-only | obsolete | The value of this object identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interfa… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.2 | ColumnexpDot5StatsLineErrors | read-only | obsolete | This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditio… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.3 | ColumnexpDot5StatsBurstErrors | read-only | obsolete | This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error). |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.4 | ColumnexpDot5StatsACErrors | read-only | obsolete | This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is e… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.5 | ColumnexpDot5StatsAbortTransErrors | read-only | obsolete | This counter is incremented when a station transmits an abort delimiter while transmitting. |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.6 | ColumnexpDot5StatsInternalErrors | read-only | obsolete | This counter is incremented when a station recognizes an internal error. |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.7 | ColumnexpDot5StatsLostFrameErrors | read-only | obsolete | This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip … |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.8 | ColumnexpDot5StatsReceiveCongestions | read-only | obsolete | This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station … |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.9 | ColumnexpDot5StatsFrameCopiedErrors | read-only | obsolete | This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a … |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.10 | ColumnexpDot5StatsTokenErrors | read-only | obsolete | This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted. |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.11 | ColumnexpDot5StatsSoftErrors | read-only | obsolete | The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Sof… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.12 | ColumnexpDot5StatsHardErrors | read-only | obsolete | The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.13 | ColumnexpDot5StatsSignalLoss | read-only | obsolete | The number of times this interface has detected the loss of signal condition from the ring. |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.14 | ColumnexpDot5StatsTransmitBeacons | read-only | obsolete | The number of times this interface has transmitted a beacon frame. |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.15 | ColumnexpDot5StatsRecoverys | read-only | obsolete | The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This counter signifies the number of time… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.16 | ColumnexpDot5StatsLobeWires | read-only | obsolete | The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and expDot5RingState will signify thi… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.17 | ColumnexpDot5StatsRemoves | read-only | obsolete | The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state an… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.18 | ColumnexpDot5StatsSingles | read-only | obsolete | The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if th… |
| 1.3.6.1.4.1.49.2.4.1.1.2.1.19 | ColumnexpDot5StatsFreqErrors | read-only | obsolete | The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by more than that ispecified by th… |
| 1.3.6.1.4.1.49.2.4.1.1.3 | NodeexpDot5Tests | |||
| 1.3.6.1.4.1.49.2.4.1.1.3.1 | NodetestInsertFunc | |||
| 1.3.6.1.4.1.49.2.4.1.1.4 | NodeexpDot5ChipSets | |||
| 1.3.6.1.4.1.49.2.4.1.1.4.1 | NodechipSetIBM16 | |||
| 1.3.6.1.4.1.49.2.4.1.1.4.2 | NodechipSetTItms380 | |||
| 1.3.6.1.4.1.49.2.4.1.1.4.3 | NodechipSetTItms380c16 | |||
| 1.3.6.1.4.1.49.2.4.1.1.5 | TableexpDot5TimerTable | not-accessible | obsolete | This table contains Token Ring interface timer values, one entry per 802.5 interface. |
| 1.3.6.1.4.1.49.2.4.1.1.5.1 | RowexpDot5TimerEntry | not-accessible | obsolete | A list of Token Ring timer values for an 802.5 interface. |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.1 | ColumnexpDot5TimerIfIndex | read-only | obsolete | The value of this object identifies the 802.5 interface for which this entry contains timer values. The value of this object for a particular interface has the… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.2 | ColumnexpDot5TimerReturnRepeat | read-only | obsolete | The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be greater than the maximum ring l… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.3 | ColumnexpDot5TimerHolding | read-only | obsolete | Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds. Implementors are encouraged to provide… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.4 | ColumnexpDot5TimerQueuePDU | read-only | obsolete | The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0, in units of 100 micro-seconds.… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.5 | ColumnexpDot5TimerValidTransmit | read-only | obsolete | The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds. Implementors are encouraged to provi… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.6 | ColumnexpDot5TimerNoToken | read-only | obsolete | The time-out value used to recover from various-related error situations [9]. If N is the maximum number of stations on the ring, the value of this timer is no… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.7 | ColumnexpDot5TimerActiveMon | read-only | obsolete | The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-seconds. Implementors are encour… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.8 | ColumnexpDot5TimerStandbyMon | read-only | obsolete | The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuous stream of tokens, in units of… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.9 | ColumnexpDot5TimerErrorReport | read-only | obsolete | The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds. Implem… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.10 | ColumnexpDot5TimerBeaconTransmit | read-only | obsolete | The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering the Bypass state, in units of 10… |
| 1.3.6.1.4.1.49.2.4.1.1.5.1.11 | ColumnexpDot5TimerBeaconReceive | read-only | obsolete | The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering the Bypass state, in units of 1… |
| 1.3.6.1.4.1.49.2.4.14 | Nodedot1dBridge | |||
| 1.3.6.1.4.1.49.2.5 | NodechipTTY | |||
| 1.3.6.1.4.1.49.2.5.1 | ScalarchipTTYNumber | read-only | mandatory | The number of terminal ports on this agent product. |
| 1.3.6.1.4.1.49.2.5.2 | TablechipTTYTable | not-accessible | mandatory | A table of TTY specific information associated with this agent. |
| 1.3.6.1.4.1.49.2.5.2.1 | RowchipTTYEntry | not-accessible | mandatory | A profile of a specific TTY interface associated with this agent. |
| 1.3.6.1.4.1.49.2.5.2.1.1 | ColumnchipTTYIndex | read-only | mandatory | The TTY to which this entry refers. |
| 1.3.6.1.4.1.49.2.5.2.1.2 | ColumnchipTTYBaud | read-write | mandatory | The baud rate for this TTY. It should be noted that all serial ports do not support all of the above baud rates. |
| 1.3.6.1.4.1.49.2.5.2.1.3 | ColumnchipTTYParity | read-write | mandatory | The parity setting for this TTY. |
| 1.3.6.1.4.1.49.2.5.2.1.4 | ColumnchipTTYStop | read-write | mandatory | The number of stop bits for this TTY. |
| 1.3.6.1.4.1.49.2.5.2.1.5 | ColumnchipTTYData | read-write | mandatory | The number of data bits for this TTY. |
| 1.3.6.1.4.1.49.2.5.2.1.6 | ColumnchipTTYTimeout | read-write | mandatory | The number of minutes to wait before this agent logs out an inactive login session on this TTY. NOTE: In some implementations, this is a single variable that i… |
| 1.3.6.1.4.1.49.2.5.2.1.7 | ColumnchipTTYPrompt | read-write | mandatory | The terminal prompt to display on this TTY. NOTE: In some implementations, this is a single variable that is used by all of the terminal and telnet sessions. |
| 1.3.6.1.4.1.49.2.5.2.1.8 | ColumnchipTTYDTR | read-write | mandatory | This value dictates the behavior of the RS-232 Data Terminal Ready (DTR) signal at the time a session ends due to a logout, timeout, or shutdown. This is used … |
| 1.3.6.1.4.1.49.2.5.2.1.9 | ColumnchipTTYTerminalType | read-write | mandatory | A string which indicates the type of terminal that is attached to the serial port. It should be noted that the string is passed to a telnet server whenever the… |
| 1.3.6.1.4.1.49.2.6 | NodechipTFTP | |||
| 1.3.6.1.4.1.49.2.6.1 | ScalarchipTFTPStart | read-write | mandatory | Setting chipTFTPStart to tftpGet(2) initiates a file transfer to the agent (download); tftpPut(3) initiates a file transfer to the server (upload). |
| 1.3.6.1.4.1.49.2.6.2 | ScalarchipTFTPSlot | read-write | mandatory | The slot number of the module that is to be involved in the TFTP transfer with the TFTP server (chipTFTPIpAddress). |
| 1.3.6.1.4.1.49.2.6.3 | ScalarchipTFTPIpAddress | read-write | mandatory | The IP Address of the TFTP server. |
| 1.3.6.1.4.1.49.2.6.4 | ScalarchipTFTPFileName | read-write | mandatory | The file name of the file to retrieve (tftpGet), or the name of the file to create (tftpPut). |
| 1.3.6.1.4.1.49.2.6.5 | ScalarchipTFTPFileType | read-write | mandatory | The type of file image to upload/download. The file type indicates to the agent what kind of file it is receiving. flashCode(1) indicates a code upgrade of the… |
| 1.3.6.1.4.1.49.2.6.6 | ScalarchipTFTPResult | read-only | mandatory | The result of the last TFTP operation. |
| 1.3.6.1.4.1.49.2.6.7 | ScalarchipTFTPSubSlot | read-write | mandatory | The subslot identifier for the module to be involved in the TFTP transfer with the TFTP server. If this transfer involves a module not contained in the ONcore … |
| 1.3.6.1.4.1.49.2.6.8 | ScalarchipTFTPTargetLocation | read-write | mandatory | Specifies the ultimate destination of the file being transfered. This object will determine if the target is Device or Module. |
| 1.3.6.1.4.1.49.2.7 | NodechipDownload | |||
| 1.3.6.1.4.1.49.2.7.1 | ScalarchipDownloadUDKSerial | read-write | mandatory | A string representing the serial number of the Upgrade Distribution Kit. |
| 1.3.6.1.4.1.49.2.7.2 | ScalarchipDownloadKey | read-write | mandatory | The key code provided by your VAR. Available by calling technical support at +1 508 460 6195. |
| 1.3.6.1.4.1.49.2.7.3 | ScalarchipDownloadDateTime | read-only | mandatory | The date of the last successful download in the format hh:mm day DD Mon YY |
| 1.3.6.1.4.1.49.2.8 | NodechipAlert | |||
| 1.3.6.1.4.1.49.2.8.1 | TablechipAlertTable | not-accessible | mandatory | A table of entries associated with the management of alerts on this agent. |
| 1.3.6.1.4.1.49.2.8.1.1 | RowchipAlertEntry | not-accessible | mandatory | An entry associated with the management of an alert on this agent. |
| 1.3.6.1.4.1.49.2.8.1.1.1 | ColumnchipAlertIndex | read-only | mandatory | The specific alert to manage. snmp-authentication(1) manages the standard authentication failure trap. hello(2) manages the hello trap. change(3), the change t… |
| 1.3.6.1.4.1.49.2.8.1.1.2 | ColumnchipAlertMode | read-write | mandatory | Enabling a specific alert allows that alert to be generated, or displayed at the console. If chipAlertIndex is set to port-up-down(5) then this object either o… |
| 1.3.6.1.4.1.49.2.11 | NodechipBootP | |||
| 1.3.6.1.4.1.49.2.11.1 | ScalarchipBootPStart | read-write | mandatory | Setting chipBootPStart to bootpRequest(2) initiates an BootP request to obtain configuration information from a BootP server. |
| 1.3.6.1.4.1.49.2.11.2 | ScalarchipBootPPowerUpMode | read-write | mandatory | When set to enable(1) indicates that a BootP request to obtain configuration information should be initiated following a power-up sequence. |
| 1.3.6.1.4.1.49.2.11.3 | ScalarchipBootPIpAddress | read-write | mandatory | The IP Address of the BootP server. If no IP address is defined, the broadcast address will be used in a BootP request. |
| 1.3.6.1.4.1.49.2.11.4 | ScalarchipBootPResult | read-only | mandatory | The result of the last BootP operation. |
| 1.3.6.1.4.1.49.3 | NodechipSlotUp | This trap indicates that a blade in the indicated slot is up. Usually, this trap is sent when the module is inserted into the hub. Sometimes, this trap is sent… | ||
| 1.3.6.1.4.1.49.4 | NodechipEnvironment | A chipEnvironment trap indicates a change in the concentrator's environment has occurred. The variables supplied indicate what exactly changed. | ||
| 1.3.6.1.4.1.49.5 | NodechipHardware | A chipHardware trap indicates that a soft hardware failure has been detected. An example of a soft hardware failure is too many writes to non-vatile storage. T… | ||
| 1.3.6.1.4.1.49.6 | NodechipSoftware | A chipSoftware trap indicates that a soft software failure has been detected. This is an indication to get the unit serviced. | ||
| 1.3.6.1.4.1.49.7 | NodechipChange | A chipChange trap is used to indicate that a configuration change has occurred. The actual variables that changed are included in the variables section of the … | ||
| 1.3.6.1.4.1.49.8 | NodechipFatal | A chipFatal trap is used to indicate that a fatal error has occurred. This is an indication to get the unit serviced. | ||
| 1.3.6.1.4.1.49.9 | NodechipTrunkDown | A chipTrunkDown trap indicates that trunk's status has changed to an error condition. Multiple chipTrunkDown traps may be sent if the trunk's status changes fr… | ||
| 1.3.6.1.4.1.49.10 | NodechipTrunkUp | A chipTrunkUp trap indicates that a trunk's status has changed to a non-error (okay or warning) condition. | ||
| 1.3.6.1.4.1.49.11 | NodechipPortDown | A chipPortDown trap indicates that a port's status has changed to an error condition. Multiple chipPortDown traps may be sent if the port's status changes from… | ||
| 1.3.6.1.4.1.49.12 | NodechipPortUp | A chipPortUp trap indicates that a port's status has changed to a non-error (okay or warning) condition. | ||
| 1.3.6.1.4.1.49.13 | NodechipPing | A chipPing trap is sent after the SNMP initiated PING command is completed. After the last echo request packet is sent, this trap is sent indicating the ping a… | ||
| 1.3.6.1.4.1.49.14 | NodechipAboveThreshd | A chipAboveThreshd trap indicates that a Counter or Gauge variable has exceeded its threshd. The variable which is above its threshd is the only variable in th… | ||
| 1.3.6.1.4.1.49.15 | NodechipBelowThreshd | A chipBelowThreshd trap indicates that a Counter or Gauge variable had exceeded its threshd but is now below its threshd. The variable which is below its thres… | ||
| 1.3.6.1.4.1.49.16 | NodechipModuleDown | A chipSlotDown trap indicates that management communications with the slot indicated by chipModSlotIndex has been broken. This event usually occurs when a modu… | ||
| 1.3.6.1.4.1.49.17 | NodechipModuleUp | A chipSlotUp trap indicates that management communications with the slot indicated by chipModSlotIndex has been established. This event usually occurs when a m… | ||
| 1.3.6.1.4.1.49.18 | NodechipSecurity | This trap indicates a change in the security environment. The olNetOlSecTrapReason specifies the reason for the trap. If the trap reason is intrusion-attempt(2… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| MacAddress | OCTET STRING (SIZE (6)) |