CISCO-WAN-AXIPOP-MIB
2006 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.1.2.1 | TableasmAlarmTable | not-accessible | mandatory | The ASM Alarm table. The table size is given by the value of ASMNumOfValidEntries. |
| 1.3.6.1.4.1.351.110.1.2.1.1 | RowasmAlarmEntry | not-accessible | mandatory | An entry in the Basis ASM Alarm Table. |
| 1.3.6.1.4.1.351.110.1.2.1.1.1 | ColumnasmAlarmNum | read-only | mandatory | This object is the identifier of a ASM alarm entry. The Alarm is further identified by the objects ASMAlarmType & ASMAlarmUnitNum. |
| 1.3.6.1.4.1.351.110.1.2.1.1.2 | ColumnasmAlarmType | read-only | mandatory | The value for this object indicates the type of Alarm represented in the entry of ASMAlarmTable indexed by ASMAlarmNum. |
| 1.3.6.1.4.1.351.110.1.2.1.1.3 | ColumnasmAlarmUnitNum | read-only | mandatory | This object identifies one unit among a number of identical units represented in ASMAlarmTable having the same ASMAlarmType. |
| 1.3.6.1.4.1.351.110.1.2.1.1.4 | ColumnasmAlarmThreshold | read-only | mandatory | This object specifies the threshold beyond which the alarmable unit is said to be in an abnormal state. |
| 1.3.6.1.4.1.351.110.1.2.1.1.5 | ColumnasmAlarmSeverity | read-only | mandatory | This variable specifies the severity of the alarm to be declared when the ASMAlarmThreshold specified is exceeded for the entry of ASMAlarmTable indexed by ASM… |
| 1.3.6.1.4.1.351.110.1.2.1.1.6 | ColumnasmUnitMeasurable | read-only | mandatory | This object indicates if the alarm unit is measurable by the AXIS shelf. |
| 1.3.6.1.4.1.351.110.1.2.1.1.7 | ColumnasmUnitMeasuredValue | read-only | mandatory | This object gives the mesaured value of the entity addressed by asmAlarmNum if it is measurable. |
| 1.3.6.1.4.1.351.110.1.2.1.1.8 | ColumnasmPhysicalAlarmState | read-only | mandatory | This object indicates the status of the ASM alarm represented in this entry. It is a bitmap where a set bit indicates an abnormal condition. A reset bit signif… |
| 1.3.6.1.4.1.351.110.1.2.1.1.9 | ColumnasmClrButton | read-write | mandatory | This object when set to ASMAlarmClear causes the entry in the ASMAlarmTable represented by ASMAlarmNum to be cleared. |
| 1.3.6.1.4.1.351.110.1.2.2 | ScalarasmNumOfValidEntries | read-only | mandatory | The number of valid ASMAlarmTable entries (regardless of how many are actually configured) in the table. |
| 1.3.6.1.4.1.351.110.1.2.3 | ScalarasmShelfAlarmState | read-only | mandatory | This object indicates whether any Shelf Alarm has been declared in the BASIS system. |
| 1.3.6.1.4.1.351.110.1.4.1.1 | NodeatmNetPrefixGroup | |||
| 1.3.6.1.4.1.351.110.1.4.1.1.1 | TableatmNetPrefixTable | not-accessible | mandatory | A table implemented by the UNI Management Entity on the user-side of an ATM UNI port, containing the network-prefix(es) for ATM-layer addresses in effect on th… |
| 1.3.6.1.4.1.351.110.1.4.1.1.1.1 | RowatmNetPrefixEntry | not-accessible | mandatory | An entry in the table, containing information about the ATM Prefix status. |
| 1.3.6.1.4.1.351.110.1.4.1.1.1.1.1 | ColumnaxisAtmNetPrefixPort | read-only | mandatory | The unique value which identifies the ILMI port. |
| 1.3.6.1.4.1.351.110.1.4.1.1.1.1.2 | ColumnaxisAtmNetPrefixPrefix | read-only | mandatory | The network prefix for ATM addresses which is in effect on the user-side of the ATM UNI port. |
| 1.3.6.1.4.1.351.110.1.4.1.1.1.1.3 | ColumnaxisAtmNetPrefixAdminStatus | read-write | mandatory | An indication of the validity of the network prefix for ATM addresses, on the user-side of the UNI port. |
| 1.3.6.1.4.1.351.110.1.4.1.1.1.1.4 | ColumnaxisAtmNetPrefixOperStatus | read-only | mandatory | An indication of the current registration state for the prefix: registering, de-registering, success, fail. |
| 1.3.6.1.4.1.351.110.1.4.1.2 | NodeatmAddressGroup | |||
| 1.3.6.1.4.1.351.110.1.4.1.2.1 | TableatmAddressTable | not-accessible | mandatory | A table implemented by the network-side of an ATM UNI port, containing the ATM-layer addresses in effect on the user-side of the UNI. |
| 1.3.6.1.4.1.351.110.1.4.1.2.1.1 | RowatmAddressEntry | not-accessible | mandatory | Information about a single ATM-layer address in effect on the user-side of a UNI port. |
| 1.3.6.1.4.1.351.110.1.4.1.2.1.1.1 | ColumnaxisAtmAddressPort | read-only | mandatory | A unique value which identifies this port. The value of 0 has the special meaning of identifying the local UNI. |
| 1.3.6.1.4.1.351.110.1.4.1.2.1.1.2 | ColumnaxisAtmAddressAtmAddress | read-only | mandatory | The ATM address which is in effect on the user-side of the ATM UNI port. |
| 1.3.6.1.4.1.351.110.1.4.1.2.1.1.3 | ColumnaxisAtmAddressStatus | read-only | mandatory | An indication of the validity of the ATM address at the user-side of the UNI port. |
| 1.3.6.1.4.1.351.110.2.6 | NodecommonPort | |||
| 1.3.6.1.4.1.351.110.2.6.1 | TablecommonPortTable | not-accessible | mandatory | The common port table is for the common ports. |
| 1.3.6.1.4.1.351.110.2.6.1.1 | RowcommonPortTableEntry | not-accessible | mandatory | An entry for every common port group. |
| 1.3.6.1.4.1.351.110.2.6.1.1.1 | ColumncommonPortNum | read-only | mandatory | This is the index to the port number. |
| 1.3.6.1.4.1.351.110.2.6.1.1.2 | ColumncommonPortType | read-only | mandatory | This is the type of the port. 1 - Frame Relay Port. 2 - ATM Port. 3 - IMA Port. |
| 1.3.6.1.4.1.351.110.2.6.1.1.3 | ColumncommonPortStatus | read-only | mandatory | This variable enables or disables the port 1 - disable 2 - enable |
| 1.3.6.1.4.1.351.110.2.6.1.1.4 | ColumncommonPortSpeed | read-only | mandatory | This is the speed of the port in cells per second. |
| 1.3.6.1.4.1.351.110.2.6.1.1.5 | ColumncommonPortAlarmState | read-only | mandatory | This variable states the alarm status of the port 1 - port in alarm 2 - port out of alarm |
| 1.3.6.1.4.1.351.110.2.6.1.1.6 | ColumncommonPortSignallingProtocolType | read-only | mandatory | This variable indicates the signalling protocol type of the port. This field is TBD. It is unused in IMATM/AUSM. |
| 1.3.6.1.4.1.351.110.2.6.1.1.7 | ColumncommonPortSignallingState | read-only | mandatory | This variable indicates the signalling state of the port. |
| 1.3.6.1.4.1.351.110.2.6.1.1.8 | ColumncommonPortAssocLines | read-only | mandatory | This variable indicates the list of physical lines in the port delimited by dots. |
| 1.3.6.1.4.1.351.110.2.6.1.1.9 | ColumncommonPortAssocChannels | read-only | mandatory | The variable indicates the list of channels that are used in the ds1 frame. |
| 1.3.6.1.4.1.351.110.2.7 | NodecommonChannel | |||
| 1.3.6.1.4.1.351.110.2.7.1 | TablecommonChanTable | not-accessible | mandatory | The common port table is for the common ports. |
| 1.3.6.1.4.1.351.110.2.7.1.1 | RowcommonChanTableEntry | not-accessible | mandatory | An entry for every common port group. |
| 1.3.6.1.4.1.351.110.2.7.1.1.1 | ColumncommonChanNum | read-only | mandatory | This is the index to the channel number. |
| 1.3.6.1.4.1.351.110.2.7.1.1.2 | ColumncommonConnType | read-only | mandatory | This specifies the connection type 1 ==> Virtual Path Connection 2 ==> Virtual Channel Connection |
| 1.3.6.1.4.1.351.110.2.7.1.1.3 | ColumncommonChanStatus | read-only | mandatory | This variable indicates the state of the VC (channel)( |
| 1.3.6.1.4.1.351.110.2.7.1.1.4 | ColumncommonAlarmState | read-only | mandatory | This is the alarm state of the port. |
| 1.3.6.1.4.1.351.110.2.7.1.1.5 | ColumncommonChanPortNum | read-only | mandatory | This variable indicates the port number associated with the channel |
| 1.3.6.1.4.1.351.110.2.7.1.1.6 | ColumncommonChanServiceType | read-only | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Associated Bit Rate |
| 1.3.6.1.4.1.351.110.2.7.1.1.7 | ColumncommonChanIngrXmtState | read-only | mandatory | This variable indicates the transmit state of the VC (channel) on the CellBus side (Ingress) |
| 1.3.6.1.4.1.351.110.2.7.1.1.8 | ColumncommonChanIngrRcvState | read-only | mandatory | This variable indicates the status of port receive (Ingress) |
| 1.3.6.1.4.1.351.110.2.7.1.1.9 | ColumncommonChanEgrXmtState | read-only | mandatory | indicates the status of port transmit(Egress) |
| 1.3.6.1.4.1.351.110.2.7.1.1.10 | ColumncommonChanEgrRcvState | read-only | mandatory | Indicates the receiving state of the VC (channel) on the Cellbus side (Egress) |
| 1.3.6.1.4.1.351.110.2.7.1.1.11 | ColumncommonConnParm1 | read-only | mandatory | Connection paramter 1 |
| 1.3.6.1.4.1.351.110.2.7.1.1.12 | ColumncommonConnParm2 | read-only | mandatory | Connection paramter 2 |
| 1.3.6.1.4.1.351.110.2.9 | NodecardResourcePartition | |||
| 1.3.6.1.4.1.351.110.2.9.1 | ScalarcardLcnPartitionType | read-write | mandatory | This object specified the type of partition on LCN: 1. noPartition the totoal (G)LCNs limited by the card 2. controllerBased available to each controller is fi… |
| 1.3.6.1.4.1.351.110.2.9.2 | TablecardResPartGrpTable | not-accessible | mandatory | This table contains the configuration of all the resource partition(s) that are on the card level, such as (G)LCN (if the object cardLcnPartitionType is config… |
| 1.3.6.1.4.1.351.110.2.9.2.1 | RowcardResPartGrpEntry | not-accessible | mandatory | This is an entry for a controller |
| 1.3.6.1.4.1.351.110.2.9.2.1.1 | ColumncardResPartCtrlrNum | read-only | mandatory | This object is the index to the table |
| 1.3.6.1.4.1.351.110.2.9.2.1.2 | ColumncardResPartRowStatus | read-write | mandatory | This object is records the status of this entry |
| 1.3.6.1.4.1.351.110.2.9.2.1.3 | ColumncardResPartNumOfLcnAvail | read-write | mandatory | This object is configured to reserve the number of (G)LCNs for one controller on a SM card, it can be used on any port but the total number of connections adde… |
| 1.3.6.1.4.1.351.110.3.1 | NodeaumClockConfig | |||
| 1.3.6.1.4.1.351.110.3.1.1 | ScalarprimaryMuxClockSource | read-write | mandatory | Primary Mux Clock source for AUM card. |
| 1.3.6.1.4.1.351.110.3.1.2 | ScalarsecondaryMuxClockSource | read-write | mandatory | Secondary clock source for AUM card. |
| 1.3.6.1.4.1.351.110.3.1.3 | ScalarcurrentClock | read-write | mandatory | clock source currently selected for AUM card. |
| 1.3.6.1.4.1.351.110.3.1.4 | ScalarclockSwitchState | read-only | mandatory | clock source switched. |
| 1.3.6.1.4.1.351.110.3.1.5 | ScalarextClockPresent | read-only | mandatory | Status of External T1/E1 Clock on AUM card. |
| 1.3.6.1.4.1.351.110.3.1.6 | ScalarextClkSrcImpedance | read-write | mandatory | Impedance on external clock input for AUM card. |
| 1.3.6.1.4.1.351.110.3.1.7 | ScalarextClkConnectorType | read-write | mandatory | This object describes the type of connector available for connecting the external clock source to the AUM-LM. The T3 and E3 cards are separate hence this field… |
| 1.3.6.1.4.1.351.110.3.2 | NodeaumAddressTranslation | |||
| 1.3.6.1.4.1.351.110.3.2.1 | TableaumAddressTranslationTable | not-accessible | mandatory | This table contains address translation parameters for AXIS connections. |
| 1.3.6.1.4.1.351.110.3.2.1.1 | RowaumAddressTranslationEntry | not-accessible | mandatory | This entry exists when the connection specified by connShelfNum, connSlotNum and connChanNum exists. |
| 1.3.6.1.4.1.351.110.3.2.1.1.1 | ColumnconnShelfNum | read-only | mandatory | Index to shelf list on BASIS. |
| 1.3.6.1.4.1.351.110.3.2.1.1.2 | ColumnconnSlotNum | read-only | mandatory | Index to slot list on BASIS. |
| 1.3.6.1.4.1.351.110.3.2.1.1.3 | ColumnconnChanNum | read-only | mandatory | Index to channel list on BASIS. |
| 1.3.6.1.4.1.351.110.3.2.1.1.4 | ColumnaumConnType | read-only | mandatory | Virtual channel connection or Virtual Path Connection |
| 1.3.6.1.4.1.351.110.3.2.1.1.5 | ColumnconnVPINum | read-only | mandatory | Virtual channel connection or Virtual Path Connection |
| 1.3.6.1.4.1.351.110.3.2.2 | TableaumAddressTranslationDeleteTable | not-accessible | mandatory | This table contains address translation parameters for AXIS connections. |
| 1.3.6.1.4.1.351.110.3.2.2.1 | RowaumAddressTranslationDeleteEntry | not-accessible | mandatory | This entry controls bulk deletion of connections on a given AXIS slot. |
| 1.3.6.1.4.1.351.110.3.2.2.1.1 | ColumndelShelfNum | read-write | mandatory | Index to shelf list on AXIS. |
| 1.3.6.1.4.1.351.110.3.2.2.1.2 | ColumndelSlotNum | read-write | mandatory | Index to slot list on BASIS. |
| 1.3.6.1.4.1.351.110.3.2.3 | ScalarconnNumOfValidEntries | read-only | mandatory | Number of rows in aumAddressTranslationTable. |
| 1.3.6.1.4.1.351.110.3.3 | NodebnmCounters | |||
| 1.3.6.1.4.1.351.110.3.3.1 | TablebnmPortCounterTable | not-accessible | mandatory | The counter table is for the ATM interface, initially there is only one interface, but by making it a table multiple ATM interfaces can be accommodated later. |
| 1.3.6.1.4.1.351.110.3.3.1.1 | RowbnmPortCounterEntry | not-accessible | mandatory | An entry for DS3 ATM counters |
| 1.3.6.1.4.1.351.110.3.3.1.1.1 | ColumnbnmPortCounterIndex | read-only | mandatory | This specifies the BNM port being referenced. |
| 1.3.6.1.4.1.351.110.3.3.1.1.2 | ColumnbnmPortRcvCells | read-only | mandatory | The count of Received cells at the BNM port. |
| 1.3.6.1.4.1.351.110.3.3.1.1.3 | ColumnbnmPortXmtCells | read-only | mandatory | The count of cells transmitted by the BNM port. |
| 1.3.6.1.4.1.351.110.3.3.1.1.4 | ColumnbnmPortCounterClrButton | read-write | mandatory | This object when set to bnmPortCounterClear causes all counters in the row referenced by bnmPortCounterIndex to be cleared. |
| 1.3.6.1.4.1.351.110.3.3.1.1.5 | ColumnbnmPortRcvCellRate | read-only | mandatory | The number of cells received from the BNM port (trunk) per second . |
| 1.3.6.1.4.1.351.110.3.3.1.1.6 | ColumnbnmPortRcvUtilization | read-only | mandatory | The received percentage utilization of the BNM port (trunk) |
| 1.3.6.1.4.1.351.110.3.3.1.1.7 | ColumnbnmPortXmtCellRate | read-only | mandatory | The number of cells transmitted to the BNM port (trunk) per second. |
| 1.3.6.1.4.1.351.110.3.3.1.1.8 | ColumnbnmPortXmtUtilization | read-only | mandatory | The transmitted percentage utilization of the BNM port (trunk) |
| 1.3.6.1.4.1.351.110.3.3.2 | ScalarbnmPortCounterNumOfValidEntries | read-only | mandatory | This object specifies the number of rows in bnmPortCounterTable. |
| 1.3.6.1.4.1.351.110.3.3.3 | ScalarbnmCellbusXmtCellCount | read-only | mandatory | This objects is a count of cells transmitted by the BNM Cell Bus Master to the cell bus. |
| 1.3.6.1.4.1.351.110.3.3.4 | ScalarbnmCellbusNoAckCellCount | read-only | mandatory | This object is a count of cells transmitted by the BNM Cell Bus Master to the cell bus for which no acknowledgement was received i.e the slave card was missing… |
| 1.3.6.1.4.1.351.110.3.3.5 | ScalarbnmCellbusGrantCount | read-only | mandatory | This object is a count of receiver grants given by the BNM Cell Bus Master |
| 1.3.6.1.4.1.351.110.3.3.6 | ScalarbnmEgressXmtCellCountDuringAlarm | read-only | mandatory | This object is a count of cells transmitted by the Egress Engine to the port i while a T3 Alarm condition was in effect. |
| 1.3.6.1.4.1.351.110.3.3.7 | ScalarbnmEgressInvalidCellCount | read-only | mandatory | This object is a count of cells with disabled channel headers, received by the Egress Engine on the BNM and dropped. |
| 1.3.6.1.4.1.351.110.3.3.8 | ScalarbnmEgressInvalidCellHdr | read-only | mandatory | This object gives the header of the first invalid cell that was dropped by the Egress Engine on the BNM since this object was last read and/or cleared. |
| 1.3.6.1.4.1.351.110.3.3.9 | ScalarbnmIngressInvalidCellCount | read-only | mandatory | This object is a count of cells from disabled channels received by the Ingress Engine on the BNM. This is not available in Release 1. |
| 1.3.6.1.4.1.351.110.3.3.10 | ScalarbnmIngressInvalidCellHdr | read-only | mandatory | This object gives the header of the first invalid cell that was dropped by the Ingress Engine on the BNM since this object was last read and/or cleared. This i… |
| 1.3.6.1.4.1.351.110.3.3.11 | ScalarbnmCountersClrButton | read-write | mandatory | This object clears the BNM counters |
| 1.3.6.1.4.1.351.110.3.4.1 | NodeascLineCnfSigLmiGrp | |||
| 1.3.6.1.4.1.351.110.3.4.1.1 | TableascCnfSigLmiGrpTable | not-accessible | mandatory | The config table is for DS3 line interface |
| 1.3.6.1.4.1.351.110.3.4.1.1.1 | RowascCnfSigLmiGrpEntry | not-accessible | mandatory | An entry for logical line |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.1 | ColumnascLmiCnfLineNum | read-only | mandatory | Refers to the logical line index |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.2 | ColumnascLmiVpi | read-only | mandatory | VPI used for ATM LMI signalling |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.3 | ColumnascLmiVci | read-only | mandatory | VCI used for ATM LMI signalling |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.4 | ColumnascLmiEnabled | read-write | mandatory | This will enable ATM LMI signalling, or ATM LMI with the Node Status Extensions |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.5 | ColumnascLmiPollingEnabled | read-write | mandatory | This will enable ATM LMI polling |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.6 | ColumnascLmiPollingInterval | read-write | mandatory | Status Enq Polling Interval in seconds Default is 10 seconds |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.7 | ColumnascLmiTimerT393 | read-write | mandatory | Status Enq timeout interval in seconds Default is 10 seconds |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.8 | ColumnascLmiTimerT394 | read-write | mandatory | Update Status timeout interval in seconds Default is 10 seconds |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.9 | ColumnascLmiMaxRetryN394 | read-write | mandatory | Status Enq maximum retry count Default is 3 |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.10 | ColumnascLmiMaxRetryN395 | read-write | mandatory | Update Status maximum retry count Default is 3 |
| 1.3.6.1.4.1.351.110.3.4.1.1.1.11 | ColumnascLmiOperStatus | read-only | mandatory | Operational status |
| 1.3.6.1.4.1.351.110.3.4.2 | NodeascCntSigLmiGrp | |||
| 1.3.6.1.4.1.351.110.3.4.2.1 | TableascCntSigLmiGrpTable | not-accessible | mandatory | The counter table is for DS3 line interface |
| 1.3.6.1.4.1.351.110.3.4.2.1.1 | RowascCntSigLmiGrpEntry | not-accessible | mandatory | An entry for logical line |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.1 | ColumnascLmiCntLineNum | read-only | mandatory | Refers to the logical line index |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.2 | ColumnascLmiStatusTx | read-only | mandatory | The number of Status PDUs transmitted |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.3 | ColumnascLmiStatusEnqTx | read-only | mandatory | The number of Status Enquiry PDUs transmitted |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.4 | ColumnascLmiStatusAckTx | read-only | mandatory | The number of Status Ack PDUs transmitted |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.5 | ColumnascLmiUpdateStatusTx | read-only | mandatory | The number of Update Status PDUs transmitted |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.6 | ColumnascLmiStatusRx | read-only | mandatory | The number of Status PDUs received |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.7 | ColumnascLmiStatusEnqRx | read-only | mandatory | The number of Status Enquiry PDUs received |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.8 | ColumnascLmiStatusAckRx | read-only | mandatory | The number of Status Ack PDUs received |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.9 | ColumnascLmiUpdateStatusRx | read-only | mandatory | The number of Update Status PDUs received |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.10 | ColumnascLmiInvalidPduRx | read-only | mandatory | The number of Invalid PDUs received. These are PDUs with invalid SSCOP or Q.2931 header, or invalid Protocol Discriminator |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.11 | ColumnascLmiInvalidPduLenRx | read-only | mandatory | The number of PDUs received with invalid length. ATM LMI PDU Length field plus Q.2931 Header length does not equal actual message length |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.12 | ColumnascLmiUnknownPduRx | read-only | mandatory | The number of PDUs with unknown Message Type received |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.13 | ColumnascLmiInvalidIeRx | read-only | mandatory | The number of PDUs received with invalid Information Elements. This includes IEs with invalid length and missing mandatory IEs |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.14 | ColumnascLmiInvalidTransaction | read-only | mandatory | The number of invalid transactions. The transaction number of a transmitted Update Status PDU does not match the transaction number of the corresponding receiv… |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.15 | ColumnascLmiTimeoutFailure | read-only | mandatory | The number of timeout failures |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.16 | ColumnascLmiNodeStatusTx | read-only | mandatory | The number of Node Status PDUs transmitted |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.17 | ColumnascLmiNodeStatusAckTx | read-only | mandatory | The number of Node Status Ack PDUs transmitted |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.18 | ColumnascLmiNodeStatusRx | read-only | mandatory | The number of Node Status PDUs received |
| 1.3.6.1.4.1.351.110.3.4.2.1.1.19 | ColumnascLmiNodeStatusAckRx | read-only | mandatory | The number of Node Status Ack PDUs received |
| 1.3.6.1.4.1.351.110.3.4.3 | NodeascChanStateSigLmiGrp | |||
| 1.3.6.1.4.1.351.110.3.4.3.1 | TableascChanStateSigLmiGrpTable | not-accessible | mandatory | The ATM LMI Channel State table |
| 1.3.6.1.4.1.351.110.3.4.3.1.1 | RowascChanStateSigLmiGrpEntry | not-accessible | mandatory | An entry for a Channel |
| 1.3.6.1.4.1.351.110.3.4.3.1.1.1 | ColumnascLmiVccLineNum | read-only | mandatory | Refers to the line number |
| 1.3.6.1.4.1.351.110.3.4.3.1.1.2 | ColumnascLmiVccVpi | read-only | mandatory | Refers to the Virtual Path Indicator |
| 1.3.6.1.4.1.351.110.3.4.3.1.1.3 | ColumnascLmiVccVci | read-only | mandatory | Refers to the Virtual Channel Indicator |
| 1.3.6.1.4.1.351.110.3.4.3.1.1.4 | ColumnascLmiXmtAbitState | read-only | mandatory | This is the transmit A bit state 0 - A bit clear = not active 1 - A bit set = active |
| 1.3.6.1.4.1.351.110.3.4.3.1.1.5 | ColumnascLmiRcvAbitState | read-only | mandatory | This is the receive A bit state 0 - A bit clear = not active 1 - A bit set = active |
| 1.3.6.1.4.1.351.110.3.5 | NodeascFeatures | |||
| 1.3.6.1.4.1.351.110.3.5.1 | ScalarredundancyAllowed | read-only | mandatory | BRAM parameter indicating whether redundancy is allowed in this shelf. |
| 1.3.6.1.4.1.351.110.3.6 | NodesmFeatures | |||
| 1.3.6.1.4.1.351.110.3.6.1 | ScalarchannelizedAllowed | read-only | mandatory | BRAM parameter indicating whether this card will support DS0 channels. |
| 1.3.6.1.4.1.351.110.3.6.2 | ScalarrateControlAllowed | read-only | mandatory | BRAM parameter indicating whether this card will support foresight. |
| 1.3.6.1.4.1.351.110.3.6.3 | ScalarsvcAllowed | read-only | mandatory | BRAM parameter indicating whether this card will support svc. |
| 1.3.6.1.4.1.351.110.3.6.4 | ScalarfuniAllowed | read-only | mandatory | BRAM parameter indicating whether this card will support FUNI. |
| 1.3.6.1.4.1.351.110.3.6.5 | ScalarimaAllowed | read-only | mandatory | BRAM parameter indicating whether this card will support Inverse Multiplexing for ATM (IMA) feature |
| 1.3.6.1.4.1.351.110.3.6.6 | ScalarmulTrksAllowed | read-only | mandatory | BRAM parameter indicating whether this card will support multiple IMA trunks feature. A value of 1 indicates that the feature is not allowed and a value of 2 i… |
| 1.3.6.1.4.1.351.110.3.6.7 | ScalaregrQosFeature | read-only | mandatory | If this is set to egrQosFeatureEnabled then the various class of service viz. Hi Priority, VBR rt, etc. as defined by the channel MIB object chanServType are s… |
| 1.3.6.1.4.1.351.110.3.7 | NodesmRateControlConfig | |||
| 1.3.6.1.4.1.351.110.3.7.1 | ScalarrateUp | read-write | mandatory | Rate Up value for this card. |
| 1.3.6.1.4.1.351.110.3.7.2 | ScalarrateDown | read-write | mandatory | Rate Down value for this card. |
| 1.3.6.1.4.1.351.110.3.7.3 | ScalarrateFastDown | read-write | mandatory | Rate Fast Down value for this card. |
| 1.3.6.1.4.1.351.110.3.7.4 | ScalarrtdMeasurementTime | read-write | mandatory | Round Trip delay measurement time in secs for this card. |
| 1.3.6.1.4.1.351.110.3.7.5 | ScalarqirTimeout | read-write | mandatory | QIR timeout in secs for this card. |
| 1.3.6.1.4.1.351.110.3.8 | NodeimatmClkCfgGrp | |||
| 1.3.6.1.4.1.351.110.3.8.1 | ScalarprimaryClockSource | read-write | mandatory | Primary reference for the clock source. Each of these codes are to be interpreted as follows: liu-rclk0: Recovered clock from physical line 0 liu-rclk1: Recove… |
| 1.3.6.1.4.1.351.110.3.8.2 | ScalarsecondaryClockSource | read-write | mandatory | Secondary reference for the clock source. Each of these codes are to be interpreted as follows: liu-rclk0: Recovered clock from physical line 0 liu-rclk1: Reco… |
| 1.3.6.1.4.1.351.110.3.8.3 | ScalarcurrentClockSource | read-write | mandatory | This object holds the current source for the clock |
| 1.3.6.1.4.1.351.110.3.9 | NodeimatmDsx3CntrsGrp | |||
| 1.3.6.1.4.1.351.110.3.9.1 | TableimatmDsx3PortCntrsGrpTable | not-accessible | mandatory | The dsx3 port counters table is for the DS3 port in IMATM. At present there is only one entry (corresponding to the single DS3 port available). This structure … |
| 1.3.6.1.4.1.351.110.3.9.1.1 | RowimatmDsx3PortCntrsEntry | not-accessible | mandatory | An entry for each T3 port (total of only one entry at present) |
| 1.3.6.1.4.1.351.110.3.9.1.1.1 | ColumnimatmDsx3PortIndex | read-only | mandatory | Index to the dsx3 port number |
| 1.3.6.1.4.1.351.110.3.9.1.1.2 | ColumnimatmDsx3PortRcvCells | read-only | mandatory | Number of cells received on the DS3 port |
| 1.3.6.1.4.1.351.110.3.9.1.1.3 | ColumnimatmDsx3PortXmtCells | read-only | mandatory | Number of cells transmitted on the DS3 port |
| 1.3.6.1.4.1.351.110.3.9.1.1.4 | ColumnimatmPortRcvInvCells | read-only | mandatory | Number of invalid cells received on the DS3 port |
| 1.3.6.1.4.1.351.110.3.9.1.1.5 | ColumnimatmPortCntrClrButton | read-write | mandatory | This variable is used to clear all the counters maintained by the card for this DS3 port |
| 1.3.6.1.4.1.351.110.3.9.1.1.6 | ColumnimatmDsx3PortLastMismatchVpiVci | read-only | mandatory | This variable denotes the last mismatch VPI/VCI value that was received over the DS3 interface. |
| 1.3.6.1.4.1.351.110.3.9.1.1.7 | ColumnimatmPortImaCtrlMatchCells | read-only | mandatory | This variable is used to count the number of cells from the DS3 interface that were discarded due to match with IMA Control header |
| 1.3.6.1.4.1.351.110.3.10 | Nodesrm3T3CnfGrp | |||
| 1.3.6.1.4.1.351.110.3.10.1 | Tablesrm3T3CnfGrpTable | not-accessible | mandatory | The SRM 3T3 configuration table, it is the distribution of a T3 line. |
| 1.3.6.1.4.1.351.110.3.10.1.1 | Rowsrm3T3CnfGrpEntry | not-accessible | mandatory | an entry in the T3 configuration table |
| 1.3.6.1.4.1.351.110.3.10.1.1.1 | ColumnsrmT3LineNum | read-only | mandatory | Select T3 line number. There is no default value for this object. |
| 1.3.6.1.4.1.351.110.3.10.1.1.2 | ColumnsrmStartT1LineNum | read-only | mandatory | The start T1 number to be affected. There is no default value for this object. |
| 1.3.6.1.4.1.351.110.3.10.1.1.3 | ColumnsrmT1RowStatus | read-write | mandatory | a command is used to add, delete, or modify one or more DS1 mapping. Default value is delete. |
| 1.3.6.1.4.1.351.110.3.10.1.1.4 | ColumnsrmTargetSlotNum | read-write | mandatory | specify the target slot number to be linked. There is no default value for this object. For MGX8850: SRM01 services slots 1 - 6 and 9 - 14, SRM02 services slot… |
| 1.3.6.1.4.1.351.110.3.10.1.1.5 | ColumnsrmTargetSlotLineNum | read-write | mandatory | 0 means not assigned. There is no default value for this object. |
| 1.3.6.1.4.1.351.110.3.11 | NodesmCardUtilization | |||
| 1.3.6.1.4.1.351.110.3.11.1 | ScalarcardOversubscribed | read-only | mandatory | This variable indicates the whether the card is over subscribed or not |
| 1.3.6.1.4.1.351.110.3.11.2 | ScalarcardIngrPercentUtil | read-only | mandatory | Percentage Utilization of the Card in the Ingress direction. |
| 1.3.6.1.4.1.351.110.3.12 | NodebnmLineInterfaceMode | |||
| 1.3.6.1.4.1.351.110.3.12.1 | ScalarbnmLineInterfaceFormat | read-write | mandatory | This indicates the format of the cells going out on the BNM trunk For T3 and E3 cards its currently fixed at STI mode. BNM-155 sonet cards can take on UNI or N… |
| 1.3.6.1.4.1.351.110.3.13 | NodeimatmVpTrkGrp | |||
| 1.3.6.1.4.1.351.110.3.13.1 | NodeimatmVpTrkMapGrp | |||
| 1.3.6.1.4.1.351.110.3.13.1.1 | TableimatmVpTrkMapGrpTable | not-accessible | mandatory | The imatmVpTrkMapGrpTable entry contains the information for mapping VPI ranges to different trunks in IMATM. |
| 1.3.6.1.4.1.351.110.3.13.1.1.1 | RowimatmVpTrkMapGrpTableEntry | not-accessible | mandatory | An entry for each VPI range |
| 1.3.6.1.4.1.351.110.3.13.1.1.1.1 | ColumnimatmRangeNum | read-only | mandatory | An index to the VpTrkTbl |
| 1.3.6.1.4.1.351.110.3.13.1.1.1.2 | ColumnimatmTrkNum | read-write | mandatory | This variable refers to the trunk number on the IMATM card. The trunk number is the same as logical port number. |
| 1.3.6.1.4.1.351.110.3.13.1.1.1.3 | ColumnimatmTrkMinVp | read-write | mandatory | This variable refers to the minimum VPI value to be configured in the range of VPIs that are to be mapped to an IMATM trunk. |
| 1.3.6.1.4.1.351.110.3.13.1.1.1.4 | ColumnimatmTrkMaxVp | read-write | mandatory | This variable refers to the maximum VPI value to be configured in the range of VPIs that are to be mapped to an IMATM trunk. It should be necessarily greater t… |
| 1.3.6.1.4.1.351.110.3.13.1.1.1.5 | ColumnimatmTrkOpType | read-write | mandatory | This variable refers to the operation type for the VPI range in question. 'disable' deletes an existing row from the table 'enable' adds a new row to the table… |
| 1.3.6.1.4.1.351.110.3.13.1.2 | ScalarnextRangeNumAvail | read-only | mandatory | This variable indicates the next range number to be used as the index for the VpTrkTbl. |
| 1.3.6.1.4.1.351.110.3.13.2 | NodeimatmVpTrkClrGrp | |||
| 1.3.6.1.4.1.351.110.3.13.2.1 | TableimatmVpTrkClrGrpTable | not-accessible | mandatory | This table is for each trunk in IMATM and is used if the user wishes to remove all VPI ranges for an IMATM trunk. |
| 1.3.6.1.4.1.351.110.3.13.2.1.1 | RowimatmVpTrkClrGrpEntry | not-accessible | mandatory | An entry for each IMATM trunk |
| 1.3.6.1.4.1.351.110.3.13.2.1.1.1 | ColumnimatmClrVpTrkNum | read-only | mandatory | This variable is used to identify the IMATM trunk number on which the 'Clear Map Table' operation needs to be done. |
| 1.3.6.1.4.1.351.110.3.13.2.1.1.2 | ColumnimatmClrVpTrkButton | read-write | mandatory | This variable implements the 'Clear Map Table' for a specified IMATM trunk. |
| 1.3.6.1.4.1.351.110.3.14 | Nodedsx3CardSpecCnfgGrp | |||
| 1.3.6.1.4.1.351.110.3.14.1 | TableimatmDsx3CardSpecConfigGrpTable | not-accessible | mandatory | The dsx3 Card spec Config group table will contain all the configuration variable for DSX3. Right now there is only one configurable parameter in this group. M… |
| 1.3.6.1.4.1.351.110.3.14.1.1 | RowimatmDsx3CardSpecConfigEntry | not-accessible | mandatory | Each entry gives the config parameters for the given port. |
| 1.3.6.1.4.1.351.110.3.14.1.1.1 | Columnimatmdsx3PortIndex | read-only | mandatory | Index to the dsx3 port number |
| 1.3.6.1.4.1.351.110.3.14.1.1.2 | ColumnimatmDsx3SingleBitErrCorrEnable | read-write | mandatory | This variable refers to dsx3 HEC correction enabled/disabled default is disable. |
| 1.3.6.1.4.1.351.110.3.15 | NodepxmFeatures | |||
| 1.3.6.1.4.1.351.110.3.15.1 | ScalarvsiControllersAllowed | read-only | mandatory | This respesents bit map of the VSI Controllers supported. Currently, we have BIT 0 - PAR BIT 1 - PNNI BIT 2 - TAG (e.g. A value of 1 in BIT 0 indicates the pre… |
| 1.3.6.1.4.1.351.110.3.15.2 | ScalarapsCardAttributes | read-only | mandatory | This respesents bit map of the APS card attributes supported. Currently, we have BIT 0, 1 - unused BIT 2 - APS standard protocol configured (1 = TRUE ; 0 = FAL… |
| 1.3.6.1.4.1.351.110.3.15.3 | ScalartrkCACEnable | read-write | mandatory | This MIB variable allows one to add a new connection on the feeder trunk even if it is over-subscribed. |
| 1.3.6.1.4.1.351.110.3.16 | NodepxmClockConfig | |||
| 1.3.6.1.4.1.351.110.3.16.1 | ScalarpxmPrimaryMuxClockSource | read-only | mandatory | Primary Mux Clock source for PXM card. For pxmInbandClock1 and pxmInbandClock2, the pxmPrimaryInbandClockSourceLineNumber described the Line number that the cl… |
| 1.3.6.1.4.1.351.110.3.16.2 | ScalarpxmPrimaryInbandClockSourceLineNumber | read-only | mandatory | If pxmPrimaryMuxClockSource is pxmInbandClock1 (1) or pxmServiceModuleClock2 (5), then this entry indicates Inband Line number. |
| 1.3.6.1.4.1.351.110.3.16.3 | ScalarpxmPrimarySMClockSourceSlotNumber | read-only | mandatory | If pxmPrimaryMuxClockSource is pxmServiceModuleClock1(2) or pxmServiceModuleClock2 (6), then this entry indicates SM slot number. |
| 1.3.6.1.4.1.351.110.3.16.4 | ScalarpxmSecondaryMuxClockSource | read-only | mandatory | Secondary clock source for PXM card. For pxmInbandClock1 and pxmInbandClock2, the pxmSecondaryInbandClockSourceLineNumber described the Line number that the cl… |
| 1.3.6.1.4.1.351.110.3.16.5 | ScalarpxmSecondaryInbandClockSourceLineNumber | read-only | mandatory | If pxmSecondaryMuxClockSource is pxmInbandClock1 (1) or pxmServiceModuleClock2 (5), then this entry indicates Inband Line number . |
| 1.3.6.1.4.1.351.110.3.16.6 | ScalarpxmSecondarySMClockSourceSlotNumber | read-only | mandatory | If pxmSecondaryMuxClockSource is pxmServiceModuleClock1(2) or pxmServiceModuleClock2 (6), then this entry indicates SM slot number . |
| 1.3.6.1.4.1.351.110.3.16.7 | ScalarpxmCurrentClock | read-only | mandatory | Clock source currently selected for PXM card. If the pxmCurrentClock is primary then the pxmPrimaryMuxClockSource described further the source of the clock. If… |
| 1.3.6.1.4.1.351.110.3.16.8 | ScalarpxmPreviousClock | read-only | mandatory | Clock source Previously selected for PXM card. |
| 1.3.6.1.4.1.351.110.3.16.9 | ScalarpxmExtClockPresent | read-only | mandatory | Status of External T1/E1 Clock on PXM card. |
| 1.3.6.1.4.1.351.110.3.16.10 | ScalarpxmExtClkSrcImpedance | read-only | mandatory | Impedance on external clock input for PXM card. |
| 1.3.6.1.4.1.351.110.3.16.11 | ScalarpxmExtClkConnectorType | read-only | mandatory | This object describes the type of connector available for connecting the external clock source to the PXM-LM. |
| 1.3.6.1.4.1.351.110.3.16.12 | ScalarpxmClkStratumLevel | read-only | mandatory | This object describes the lowest stratum level provided by the interface the external clock source to the PXM-LM. |
| 1.3.6.1.4.1.351.110.3.16.13 | ScalarpxmClkErrReason | read-only | mandatory | This object gives more information about clock status (if known). |
| 1.3.6.1.4.1.351.110.3.16.14 | ScalarpxmExtClock2Present | read-only | mandatory | Status of External T1/E1 Clock on port 2 of UI-S3 back card of PXM card. |
| 1.3.6.1.4.1.351.110.3.16.15 | ScalarpxmExtClk2SrcImpedance | read-only | mandatory | Impedance on external clock input on port 2 of UI-S3 back card of PXM card. |
| 1.3.6.1.4.1.351.110.3.16.16 | ScalarpxmExtClk2ConnectorType | read-only | mandatory | This object describes the type of connector available for connecting the external clock source to the port 2 of UI-S3 back card of PXM-LM. |
| 1.3.6.1.4.1.351.110.3.17 | NodevismConfig | |||
| 1.3.6.1.4.1.351.110.3.17.1 | NodevismIpGrp | |||
| 1.3.6.1.4.1.351.110.3.17.1.1 | ScalarvismIpAddress | read-write | mandatory | The IP address of VISM card. Each VISM card has its own IP address. IP address for each VISM card is required to communicate with the Call agent. The IP addres… |
| 1.3.6.1.4.1.351.110.3.17.1.2 | ScalarvismSubNetMask | read-write | mandatory | SUB-NETMASK of the VISM IP interface. This object is applicable if the mode is voIP or switching. From vism 2.0.3 release onwards this object can be configured… |
| 1.3.6.1.4.1.351.110.3.17.1.3 | ScalarvismControlTos | read-write | mandatory | This object is used to provision the bitmask used for the TOS (Type Of Service) octet for cells carrying the control (xGCP ) traffic. Default value 96 = 0x60 =… |
| 1.3.6.1.4.1.351.110.3.17.1.4 | ScalarvismBearerIpAddress | read-write | mandatory | The bearer IP address of VISM card. This is an optional second IP address of the VISM card. If this bearer IP address is defined, the vismIpAddress automatical… |
| 1.3.6.1.4.1.351.110.3.17.1.5 | ScalarvismBearerSubNetMask | read-write | mandatory | Bearer SUB-NETMASK of the VISM IP interface. This optional bearer subnet mask must be provided when vismBearerIpAddress is provided. From vism 2.0.3 release on… |
| 1.3.6.1.4.1.351.110.3.17.2 | NodevismVoIpGrp | |||
| 1.3.6.1.4.1.351.110.3.17.2.1 | ScalarvismBearerTos | read-write | mandatory | This object is used to provision the bitmask used for the TOS (Type Of Service) octet for cells carrying VoIP bearer (RTP ) traffic. Default value 160 = 0xA0 =… |
| 1.3.6.1.4.1.351.110.3.17.2.2 | ScalarvismRtcpRepInterval | read-write | mandatory | This attribute defines the RTCP report interval ( defined in RFC 1889). This indicates the interval at which the RTCP reports should be sent to the participati… |
| 1.3.6.1.4.1.351.110.3.17.2.3 | ScalarvismRtpReceiveTimer | read-write | mandatory | This object defines whether the RTP packets receive timer on the VISM needs to be enabled or not. For some VoIP applications (as in South Carolina release), if… |
| 1.3.6.1.4.1.351.110.3.17.2.4 | ScalarvismPacketizationPeriod | read-only | deprecated | This object is used to provision the packetization period to be applied. This object is applicable for VoIP adaptation only. For VoAAL2 adaptations, the packet… |
| 1.3.6.1.4.1.351.110.3.17.2.5 | ScalarvismVoIpDtmfRelay | read-write | mandatory | This attribute defines whether the DTMF (Dual Tone, Multi-Frequency) digits need to be transported to the other endpoint via NSE packets. The value in this obj… |
| 1.3.6.1.4.1.351.110.3.17.2.6 | ScalarvismVoIpCasTransport | read-write | mandatory | This attribute defines whether the CAS (ABCD bits) bits need to be transported to the other endpoint via NSE packets. The value in this object will be utilized… |
| 1.3.6.1.4.1.351.110.3.17.2.7 | ScalarvismVoIpTripleRedundancy | read-write | mandatory | This attribute defines whether triple redundancy is enabled or not. With triple redundancy, NSEs are sent three times at 20 ms intervals. For reliable channels… |
| 1.3.6.1.4.1.351.110.3.17.2.8 | ScalarvismVoIpVADTimer | read-write | mandatory | This attribute defines the hangover time for VAD in milliseconds. Once the voice inactivity is detected, the gateway will wait for this duration before activat… |
| 1.3.6.1.4.1.351.110.3.17.2.9 | ScalarvismVoIpNTECapabilityNegotiate | read-write | mandatory | This attribute defines whether the VISM has the capability to negotiate the list of events either NSE (Named Signal Event) or NTE (Named Telephony Events), usi… |
| 1.3.6.1.4.1.351.110.3.17.2.10 | ScalarvismVoIpSIDPayloadType | read-write | mandatory | This attribute sets the payload type of a RTP packet carrying SID which is sent to the other end when silence is detected. The default value is in accordance t… |
| 1.3.6.1.4.1.351.110.3.17.2.11 | ScalarvismVoIpDPvcOamCellGap | read-write | mandatory | This attribute defines the inter cell gap for dual PVC OAM cells. The value represents the time in milliseconds. |
| 1.3.6.1.4.1.351.110.3.17.2.12 | ScalarvismVoIpDPvcRetryCnt | read-write | mandatory | This attribute defines the threshold for failure of a PVC. If the number of consecutive OAM cells sent for which no ack was received equals this number then th… |
| 1.3.6.1.4.1.351.110.3.17.2.13 | ScalarvismVoIpDPvcRecoverCnt | read-write | mandatory | This attribute defines the threshold for recovery of a PVC. If the number of consecutive OAM cells sent for which ack was received equals this number then the … |
| 1.3.6.1.4.1.351.110.3.17.2.14 | ScalarvismRtcpRecvMultiplier | read-write | mandatory | The 'vismRtcpRepInterval' MIB object specified above defines an approximate RTCP report interval (defined in RFC 1889) which indicates the interval in millisec… |
| 1.3.6.1.4.1.351.110.3.17.2.15 | ScalarvismVoIpLapdTrunkPVC | read-write | mandatory | This object should be used for VoIP Trunking applications and only if the signalling type is configured to be CCS. By default the PRI D-channel information wil… |
| 1.3.6.1.4.1.351.110.3.17.2.16 | ScalarvismVoIpEventNegotiationPolicy | read-write | mandatory | This attribute defines whether or not the VISM should advertise the event codecs, NSE (Named Signal Events), NTE (Named Telephony Events), or Cisco-rtp, in add… |
| 1.3.6.1.4.1.351.110.3.17.3 | NodevismDspGrp | |||
| 1.3.6.1.4.1.351.110.3.17.3.1 | ScalarvismEcanCnfIdlePattern | read-only | deprecated | Echo Canceller pattern for Idle code. Mu-Law : 1 - 7f, 2 - ff, 3 - 7f or ff, 4 - f7 A-Law : 1 - None, 2 - 54, 3 - 55, 4 - Programable Idle code. DEFVAL : patte… |
| 1.3.6.1.4.1.351.110.3.17.3.2 | ScalarvismEcanCnfIdleDirection | read-only | deprecated | Echo Canceller Idle Direction. This determines in which direction the Idle code must be present. |
| 1.3.6.1.4.1.351.110.3.17.3.3 | ScalarvismCompCnfPacketSize | read-write | mandatory | Compressed output packet size - This value is used in the DSP interface API commands to configure the DSPs for the maximum packet size. The valid values are 80… |
| 1.3.6.1.4.1.351.110.3.17.3.4 | ScalarvismERL | read-write | mandatory | This object is used to provision the return echo lost, i.e the db loss of the echo that the DSPs are supposed to cancel. |
| 1.3.6.1.4.1.351.110.3.17.3.5 | ScalarvismJitterDelayMode | read-write | deprecated | This object is used to provision the jitter buffer mode to be apply to a call connection. The possible values are: fixed - means use a constant jitter buffer s… |
| 1.3.6.1.4.1.351.110.3.17.3.6 | ScalarvismJitterInitialDelay | read-write | deprecated | Defines the jitter buffer size. If the vismJitterDelayMode is set to be fixed, the jitter buffer is fixed at this value for the call. If vismJitterDelayMode is… |
| 1.3.6.1.4.1.351.110.3.17.3.7 | ScalarvismAdaptiveGainControl | read-write | mandatory | If set to on, the DSP will adjust the gain of the of the call connection to an optimal value. |
| 1.3.6.1.4.1.351.110.3.17.3.8 | ScalarvismDspHealth | read-only | mandatory | This attribute indicates the health of the DSPs. It is a percentage of the total number of DSPs that are currently functional. Currently No action is planned u… |
| 1.3.6.1.4.1.351.110.3.17.3.9 | ScalarvismUpspeedCodec | read-write | mandatory | This object specifies the codec to be used when fax upspeed happens. The default value for this object is G.711u when the line type is T1 and G.711a when the l… |
| 1.3.6.1.4.1.351.110.3.17.3.10 | ScalarvismPayloadType | read-write | mandatory | This object specifies the payload type to be used when fax upspeed happens. IANA values (0..95) are static payload and (96..127) are dynamic payload type. This… |
| 1.3.6.1.4.1.351.110.3.17.4 | NodevismSystemGrp | |||
| 1.3.6.1.4.1.351.110.3.17.4.1 | ScalarvismDaughterCardSerialNum | read-only | mandatory | A unique value for each VISM daughter card, entered in nvram by manf. The serial No. is on the non-volatile RAM on the VISM daughter card. |
| 1.3.6.1.4.1.351.110.3.17.4.2 | ScalarvismDaughterCardDescription | read-only | mandatory | Describes the VISM daughter card. |
| 1.3.6.1.4.1.351.110.3.17.4.3 | ScalarvismDaughterCardHWRev | read-only | mandatory | Hardware revision number for the daughter card. |
| 1.3.6.1.4.1.351.110.3.17.4.4 | ScalarvismEcanEncoding | read-only | mandatory | Voice encoding type, Mu-law or A-law. mu-law is returned for T1 lines and a-law is returned for E1 lines. |
| 1.3.6.1.4.1.351.110.3.17.4.5 | ScalarvismMode | read-only | mandatory | This attribute defines the connection model that the VISM card is configured to operate with. This object can be modified by CLI only. The CLI 'cnfvismmode' ca… |
| 1.3.6.1.4.1.351.110.3.17.4.6 | ScalarvismPrevMode | read-only | deprecated | This attribute indicates the mode in which VISM was operating before the vismMode value was changed. i.e It gives the value of vismMode before it got changed t… |
| 1.3.6.1.4.1.351.110.3.17.4.7 | ScalarvismCacEnable | read-write | mandatory | This attribute describes whether CAC (Connection Admission Control) functionality needs to be applied on the VISM card, on a per PVC basis. For some applicatio… |
| 1.3.6.1.4.1.351.110.3.17.4.8 | ScalarvismAvailableDs0Count | read-only | mandatory | This attribute describes the no. of DS0s available for new connections on VISM. This is modified by the VISM firmware after each connection is setup. In indian… |
| 1.3.6.1.4.1.351.110.3.17.4.9 | ScalarvismAppliedTemplate | read-only | mandatory | This attribute describes the Codec template currently configured on the VISM card. The value refers to an index to the vismCodecTemplate table. This template i… |
| 1.3.6.1.4.1.351.110.3.17.4.11 | ScalarvismTftpServerDn | read-write | mandatory | This object holds the domain name of the tftp server from where the cas module will download the cas files. This domain name can be resolved internally or exte… |
| 1.3.6.1.4.1.351.110.3.17.4.12 | ScalarvismXgcpBearerNetworkType | read-write | mandatory | This object specifies the network type to use in order to transport bearer traffic. The user can configure this to IP or ATM based on where the VISM will be lo… |
| 1.3.6.1.4.1.351.110.3.17.4.13 | ScalarvismXgcpBearerVCType | read-write | mandatory | This object specifies the vc type to use in order to transport bearer traffic. If the call agent specifies the VC type in the MGCP local connection options (CR… |
| 1.3.6.1.4.1.351.110.3.17.4.14 | ScalarvismXgcpBearerConnectionType | read-write | mandatory | This object specifies the connection type used to transport bearer traffic. If the BearerNetworkType is chosen to be IP then the value of this object has to be… |
| 1.3.6.1.4.1.351.110.3.17.4.15 | ScalarvismBearerContinuityTimer | read-write | mandatory | This object specifies the co4 (bearer continuity) timer in millisecs. The timer will be started in the terminating/orginating gateway for a duration as specifi… |
| 1.3.6.1.4.1.351.110.3.17.4.16 | ScalarvismCodecNegotiationOption | read-write | mandatory | This object helps in forming an ordered intersection of lists and one of the lists must be used in determining the resulting order of codecs. Lco - local conne… |
| 1.3.6.1.4.1.351.110.3.17.4.17 | ScalarvismProfileNegotiationOption | read-write | mandatory | This object helps in forming an ordered intersection of lists and one of the lists must be used in determining the resulting order of profiles. Lco - local con… |
| 1.3.6.1.4.1.351.110.3.17.4.18 | ScalarvismCarrierLossPolicy | read-write | mandatory | This object defines the policy that needs to be applied when a carrier loss is detected. This states whether to switch to the pre-upspeed codec or to remain wi… |
| 1.3.6.1.4.1.351.110.3.17.4.19 | ScalarvismCacRejectionPolicy | read-write | mandatory | This attribute defines the policy that needs to be applied once the CAC function rejects the upspeeding of a connection, due to a fax/modem switch-over request… |
| 1.3.6.1.4.1.351.110.3.17.4.20 | ScalarvismExtDnsServerDn | read-write | mandatory | This object refers to the domain name of the external DNS server which will be used to resolve other domain name. Currently this domain name can only be resolv… |
| 1.3.6.1.4.1.351.110.3.17.4.21 | ScalarvismFeatureBitMap | read-write | mandatory | This object denotes the bit map for VISM features. It indicates the current features that are enabled. It should be consistant with vismMode. When user change … |
| 1.3.6.1.4.1.351.110.3.17.4.22 | ScalarvismVADTolerance | read-write | mandatory | The value in this object refers to the customer accepted drop rate for voice connections when the bandwidth usage exceeds allowed value. The actual range of th… |
| 1.3.6.1.4.1.351.110.3.17.4.23 | ScalarvismVADDutyCycle | read-write | mandatory | This object refers to the talk-spurts duty cycle. The unit is in percentage. When the value of this object is to be passed to underlying CAC module in VISM thi… |
| 1.3.6.1.4.1.351.110.3.17.4.24 | ScalarvismAggregateTrafficClipping | read-write | mandatory | This attribute defines the aggregate traffic clipping policy which is applicable to all bearer traffic generated at VISM card. The applicable options are: 1 - … |
| 1.3.6.1.4.1.351.110.3.17.4.25 | ScalarvismAggregateSvcBandwidth | read-write | mandatory | The aggregate svc bandwidth is used for AAL2 SVC aggregate SVC Connection Admision Control and also used for aggregate traffic clipping at VISM card when vismA… |
| 1.3.6.1.4.1.351.110.3.17.4.26 | ScalarvismBearerContinuityTest | read-write | mandatory | This attribute defines whether the bearer continuity test for a connection will be performed at the time of call setup or not. When the vismBearerContinuityTes… |
| 1.3.6.1.4.1.351.110.3.17.4.27 | ScalarvismCaleaEnable | read-write | mandatory | This attribute describes whether CALEA (Communication Assistance for Law Enforcement Agency)) functionality needs to be enabled on the VISM card. This attribut… |
| 1.3.6.1.4.1.351.110.3.17.5 | NodevismTrapObjGrp | |||
| 1.3.6.1.4.1.351.110.3.17.5.1 | ScalarvismConfigChangeTypeBitMap | read-only | mandatory | Configuration change Type BitMap used in vismTableChanged trap and vismScalarChanged trap. When used in vismTableChanged trap, the bits indicate the following:… |
| 1.3.6.1.4.1.351.110.3.17.5.2 | ScalarvismTrapIntIndex1 | read-only | mandatory | This object is used only for the purpose of sending it in the trap varbind. This object is used for two purposes: 1. When the integer index of a SMIv2 table ha… |
| 1.3.6.1.4.1.351.110.3.17.5.3 | ScalarvismTrapIntIndex2 | read-only | mandatory | This object is used only for the purpose of sending it in the trap varbind. This object is used for two purposes: 1. This object will be used when the SMIv2 ta… |
| 1.3.6.1.4.1.351.110.3.17.5.4 | ScalarvismTrapStrIndex1 | read-only | mandatory | This object is used only for the purpose of sending it in the trap varbind. This object is used for two purposes: 1. When the OctetString index of a SMIv2 tabl… |
| 1.3.6.1.4.1.351.110.3.17.6 | NodevismAal2Grp | |||
| 1.3.6.1.4.1.351.110.3.17.6.1 | ScalarvismAal2SubcellMuxing | read-write | mandatory | This object is a card level parameter for AAL2 adaptation and it identifies the mutiplexing function of the AAL2 Common Part Sublayer. When it is disabled then… |
| 1.3.6.1.4.1.351.110.3.17.6.2 | ScalarvismAal2DtmfRelay | read-write | mandatory | This attribute defines whether the DTMF (Dual Tone Multi Frequency) digits need to be transported to the other end-point or not. The value in this object will … |
| 1.3.6.1.4.1.351.110.3.17.6.3 | ScalarvismAal2CasTransport | read-write | mandatory | This attribute defines whether the CAS (ABCD bits) bits need to be transported to the other endpoint. In the case of switching application, the CAS bits are ba… |
| 1.3.6.1.4.1.351.110.3.17.6.4 | ScalarvismAal2Type3Redundancy | read-write | mandatory | This attribute defines whether the triple redundancy is supported for type 3 packets in AAL2 SVC/PVC . When Triple redundancy is enabled , the type 3 packets (… |
| 1.3.6.1.4.1.351.110.3.17.6.5 | ScalarvismAal2VADTimer | read-write | mandatory | This attribute defines the hangover time for VAD in milliseconds. Once the voice inactivity is detected, the gateway will wait for this duration before activat… |
| 1.3.6.1.4.1.351.110.3.17.6.6 | ScalarvismAal2CidFillTimer | read-write | mandatory | This attribute defines the time (millisecs) to wait for filling up the cell when the next packet is not ready. After waiting for the time configured in this ob… |
| 1.3.6.1.4.1.351.110.3.17.7 | NodevismInteropGrp | |||
| 1.3.6.1.4.1.351.110.3.17.7.1 | ScalarvismXgcpSdpOst | read-write | mandatory | This object is used to enable/disable building of s=,t=,o= lines in SDP message. If this object is set to 'enable' then it indicates that the o=, s=, t= lines … |
| 1.3.6.1.4.1.351.110.3.17.7.2 | ScalarvismDynamicPT | read-write | mandatory | This object is used to enable / disable dynamic payload type configuration on the VISM Card. |
| 1.3.6.1.4.1.351.110.3.18 | NodesmRasConfig | |||
| 1.3.6.1.4.1.351.110.3.18.1 | ScalarrasOamlpbkAllowed | read-write | mandatory | Object indicating whether RAS- OAM loopback test is enabled or disabled for this card. |
| 1.3.6.1.4.1.351.110.3.18.2 | ScalarrasOamlpbkFrequency | read-write | mandatory | Object indicating the frequency in minutes in which RAS task sends one OAM loopback cell per idle connection. |
| 1.3.6.1.4.1.351.110.3.19 | NoderasOamLpbkInfo | |||
| 1.3.6.1.4.1.351.110.3.19.1 | ScalarchanPacketNumber | read-only | mandatory | Each trap will send status for 256 channels bitmapping the status. This object identities the chunk of 256 channels. The channel numbers for which the trap ind… |
| 1.3.6.1.4.1.351.110.3.19.2 | ScalarchanOAMstatus32 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 16 to chanPacketNumber * 256 + 47 MSB represent lower channel and LSB r… |
| 1.3.6.1.4.1.351.110.3.19.3 | ScalarchanOAMstatus64 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 48 to chanPacketNumber * 256 + 79 MSB represent lower channel and LSB r… |
| 1.3.6.1.4.1.351.110.3.19.4 | ScalarchanOAMstatus96 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 80 to chanPacketNumber * 256 + 111 MSB represent lower channel and LSB … |
| 1.3.6.1.4.1.351.110.3.19.5 | ScalarchanOAMstatus128 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 112 to chanPacketNumber * 256 + 143 MSB represent lower channel and LSB… |
| 1.3.6.1.4.1.351.110.3.19.6 | ScalarchanOAMstatus160 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 144 to chanPacketNumber * 256 + 175 MSB represent lower channel and LSB… |
| 1.3.6.1.4.1.351.110.3.19.7 | ScalarchanOAMstatus192 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 176 to chanPacketNumber * 256 + 207 MSB represent lower channel and LSB… |
| 1.3.6.1.4.1.351.110.3.19.8 | ScalarchanOAMstatus224 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 208 to chanPacketNumber * 256 + 239 MSB represent lower channel and LSB… |
| 1.3.6.1.4.1.351.110.3.19.9 | ScalarchanOAMstatus256 | read-only | mandatory | Bit map indicating Ras_oam_lpbk test state of 32 channels from chanPacketNumber * 256 + 240 to chanPacketNumber * 256 + 271 MSB represent lower channel and LSB… |
| 1.3.6.1.4.1.351.110.3.20 | NodecoreCardCommands | |||
| 1.3.6.1.4.1.351.110.3.20.1 | ScalarswitchCoreCard | read-write | mandatory | A SwitchCC command either to invoke switchcc or take noAction on the Core Card Set |
| 1.3.6.1.4.1.351.110.3.21 | NodeimaAutoRestartFeature | |||
| 1.3.6.1.4.1.351.110.3.21.1 | ScalarimaAutoRestart | read-write | mandatory | This object allows the user to enable/disable the IMA group auto-restart feature on IMA capable cards. The effect of this object is card-wide. A value of 1 dis… |
| 1.3.6.1.4.1.351.110.3.22 | NodesrmeCnfGrp | |||
| 1.3.6.1.4.1.351.110.3.22.1 | TablesrmeCnfGrpTable | not-accessible | mandatory | The SRME configuration table for bulk distribution of SRME lines. |
| 1.3.6.1.4.1.351.110.3.22.1.1 | RowsrmeCnfGrpEntry | not-accessible | mandatory | an entry in the SRME Distribution configuration table |
| 1.3.6.1.4.1.351.110.3.22.1.1.1 | ColumnsrmeLineNum | read-only | mandatory | Select SRME line number. For OC3/STM1: SYNTAX INTEGER 1 There is no default value for this object. |
| 1.3.6.1.4.1.351.110.3.22.1.1.2 | ColumnsrmeStartVtNum | read-only | mandatory | The start T1 or E1 number (virtual tributary) to be affected. For OC3 with T1 tributaries: SYNTAX INTEGER (1 .. 84) For STM1 with E1 tributaries: SYNTAX INTEGE… |
| 1.3.6.1.4.1.351.110.3.22.1.1.3 | ColumnsrmeRowStatus | read-write | mandatory | Command used to add, delete, or modify one or more T1 or E1 mappings. Only the srmeVtFramingType object can be modified once the distribution link is added. To… |
| 1.3.6.1.4.1.351.110.3.22.1.1.4 | ColumnsrmeTargetSlotNum | read-write | mandatory | specify the target slot number to be linked. There is no default value for this object. For MGX8x50: SRM01 services slots 1 - 6 and 9 - 14, SRM02 services slot… |
| 1.3.6.1.4.1.351.110.3.22.1.1.5 | ColumnsrmeTargetSlotLineNum | read-write | mandatory | Specify the target slot's line to be linked. 0 means not assigned. There is no default value for this object. |
| 1.3.6.1.4.1.351.110.3.22.1.1.6 | ColumnsrmeVtFramingType | read-write | mandatory | Specifies the Framing Type of the target slot line. This is applicable only if the target module is a T1 Service Module and byte sync mapping is used on SRME. … |
| 1.3.6.1.4.1.351.110.4.1 | NodeserialInterface | |||
| 1.3.6.1.4.1.351.110.4.1.1 | TableserialInterfaceTable | not-accessible | mandatory | This table represents Physical serial interfaces on the module |
| 1.3.6.1.4.1.351.110.4.1.1.1 | RowserialInterfaceEntry | not-accessible | mandatory | An entry for the serial interface |
| 1.3.6.1.4.1.351.110.4.1.1.1.1 | ColumnserialPortNum | read-only | mandatory | serial interface number port 1. is always defined as debug port port 2. on BSC can perform SLIP. |
| 1.3.6.1.4.1.351.110.4.1.1.1.2 | ColumnserialPortType | read-only | mandatory | On the BSC board IP stack is mounted on the manager port, on the debug port dumb terminal can be connected function of the ports cannot be changed, except for … |
| 1.3.6.1.4.1.351.110.4.1.1.1.3 | ColumnserialPortEnable | read-write | mandatory | ports can be enabled or diabled |
| 1.3.6.1.4.1.351.110.4.1.1.1.4 | ColumnserialPortbps | read-write | mandatory | baud rate of the ports, each port can be config different |
| 1.3.6.1.4.1.351.110.4.1.2 | ScalarserialPortNumOfValidEntries | read-only | mandatory | Number of rows in serialPortTable. This number is equal to the number of serial ports on the module. |
| 1.3.6.1.4.1.351.110.4.2 | NodeethernetInterface | |||
| 1.3.6.1.4.1.351.110.4.2.1 | ScalarethernetPhysicaAddress | read-only | mandatory | ethernet address stored in the BSC BRAM, entered by manfacturing. |
| 1.3.6.1.4.1.351.110.4.5.1 | Nodex21CnfGrp | |||
| 1.3.6.1.4.1.351.110.4.5.1.1 | Tablex21CnfGrpTable | not-accessible | mandatory | The X21 Configuration table. The table size is given by the value of x21LineNumofValidEntries |
| 1.3.6.1.4.1.351.110.4.5.1.1.1 | Rowx21CnfGrpEntry | not-accessible | mandatory | An entry in the X21 Configuration table. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.1 | Columnx21LineNum | read-only | mandatory | This object is the identifier of a X.21 interface. No defaults. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2 FRSM-HS2B-12IN1 supports a range from 1 to 8 |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.2 | Columnx21LineEnable | read-write | mandatory | This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify Default is enable. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.3 | Columnx21LineType | read-write | mandatory | This variable indicates the type X21 line type. The line-type affects the clock always provides the clock and DTE accepts it. dteST is only applicable to V.35 … |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.4 | Columnx21LineRate | read-write | mandatory | This variable configures the X.21/HSSI/V.35 line-rate. Note that enumerations 51 through 108 are supported only by FRSM-HS2/HS2B card. default is r48Kbps on FR… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.5 | Columnx21LineLoopbackCommand | read-write | mandatory | This variable represents the loopback state x21NoLoop Not in the loopback state. Normal traffic can be sent x21DiagnosticMetallicLoop Loopbacks the line on the… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.6 | Columnx21LineSendCode | read-write | mandatory | This variable indicates what type of code is being sent across the X.21/HSSI interface by the device. The values mean: x21NoCode: No loopback. x21SendLoopACode… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.7 | Columnx21LineLoopbackCodeDetection | read-write | mandatory | Enable detection of line Loopback Codes. In the current release, the loopback detection is implemented only in HSSI DCE mode. Default is codeDetectDisabled. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.8 | Columnx21ConnectorType | read-only | mandatory | back card type This object is not used by FRSM-HS2/HS2B |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.9 | Columnx21InvertClock | read-write | mandatory | This object configures two options: a) To invert the clock sent by HS1/HS2B with the TX data or not. b) If DCE,to expect the receive clock looped back from DTE… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.10 | Columnx21LineInterfaceType | read-write | mandatory | This object indicates serial interface type. Default is hssi. This object is not is configurable in FRSM-HS2 and FRSM-HS2B-HSSI. It will be set hssi by default… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.11 | Columnx21ClkFrequencyThreshold | read-write | mandatory | This object indicates user configurable percentage of clock frequency, which is used by DTE clock monitoring to declare clock rate out of bound alarm. This obj… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.12 | ColumnserialLineRate | read-write | mandatory | line rate for X.21/HSSI/V.35 interfaces in bps. This object is supported only by FRSM-HS2/B card, only multiples of 1000 are accepted. Default is 48Kbps for X.… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.13 | ColumnserialLineRateVariation | read-only | mandatory | This object indicates line rate variation of HSSI/X.21/V.35 DCE interfaces in ppm (parts per million). i.e. clock generated from DCE hardware interface = (seri… |
| 1.3.6.1.4.1.351.110.4.5.1.2 | Scalarx21LineNumofValidEntries | read-only | mandatory | The number of X.21/HSSI configuration entries (regardless of their current configuration) in the x21ConfigTable table. |
| 1.3.6.1.4.1.351.110.4.5.2 | Nodex21AlmCnfGrp | |||
| 1.3.6.1.4.1.351.110.4.5.2.1 | Tablex21AlmCnfGrpTable | not-accessible | mandatory | The FRSM-HS1/HS2 interface alarm configuration table. |
| 1.3.6.1.4.1.351.110.4.5.2.1.1 | Rowx21AlmCnfGrpEntry | not-accessible | mandatory | An entry in the X.21/HSSI Alarm Configuration table |
| 1.3.6.1.4.1.351.110.4.5.2.1.1.1 | Columnx21AlmCnfLineNum | read-write | mandatory | X.21/HSSI line number. No defaults. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2 FRSM-HS2B-12IN1 supports a range from 1 to 8 |
| 1.3.6.1.4.1.351.110.4.5.2.1.1.2 | Columnx21Severity | read-write | mandatory | This variable is used to setup the severity of LOS or clock mismatch alarm. Whenever the above condition arises, the FRSM-HS1/HS2/HS2B will send the alarm with… |
| 1.3.6.1.4.1.351.110.4.5.3 | Nodex21AlmGrp | |||
| 1.3.6.1.4.1.351.110.4.5.3.1 | Tablex21AlmGrpTable | not-accessible | mandatory | The X.21/HSSI interface alarm configuration table. The size of table is given by the value of x21LineNum |
| 1.3.6.1.4.1.351.110.4.5.3.1.1 | Rowx21AlmGrpEntry | not-accessible | mandatory | An entry in the X21 Alarm table |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.1 | Columnx21AlmLineNum | read-only | mandatory | This object is the identifier (line number) of a X.21/HSSI interface. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2 FRSM-HS2B-12IN1 supports a range from 1 t… |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.2 | Columnx21LineAlarmState | read-only | mandatory | This variable is a bitmap of the X21 Line ALarms on the FRSM-HS1. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alar… |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.3 | Columnx21LineEIAStatus | read-only | mandatory | Indicates the status of X.21/HSSI lines: 0x01 0x02 0x04 |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.4 | Columnx21AlarmClrButton | read-write | mandatory | This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm |
| 1.3.6.1.4.1.351.110.4.7.1 | Tabledsx0VismCnfTable | not-accessible | mandatory | The entries in this table are created and deleted implicitly at the time of adding and deleting the line. For every DS0 on a line, one row will be created. |
| 1.3.6.1.4.1.351.110.4.7.1.1 | Rowdsx0VismCnfEntry | not-accessible | mandatory | This ds0 table contains both cas related and non cas related parameters. The non cas related parameters are applicable accross all line signaling types, while … |
| 1.3.6.1.4.1.351.110.4.7.1.1.1 | Columnds0IfIndex | read-only | mandatory | This attribute defines the index for this table. This is derived from the following formula: index = 31 * (Ds1# - 1) + ds0# where : Ds1# - The T1/E1 line numbe… |
| 1.3.6.1.4.1.351.110.4.7.1.1.2 | Columnds0RobbedBitSignalling | read-write | mandatory | This object indicates if Robbed Bit Signalling is turned on or off for a given ds0. This only applies to DS0s on a DS1 link. For E1 links the value is always o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.3 | Columnds0IdleCode | read-write | mandatory | This object contains the code transmitted in the ABCD bits when the ds0 is not connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.4 | Columnds0SeizedCode | read-write | mandatory | This object contains the code transmitted in the ABCD bits when the ds0 is connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the vari… |
| 1.3.6.1.4.1.351.110.4.7.1.1.5 | Columnds0ReceivedCode | read-only | mandatory | This object contains the code being received in the ABCD bits. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit 1 (value 2) … |
| 1.3.6.1.4.1.351.110.4.7.1.1.6 | Columnds0TransmitCodesEnable | read-only | deprecated | This object determines if the idle and seized codes are transmitted. If the value of this object is true then the codes are transmitted. This object is not app… |
| 1.3.6.1.4.1.351.110.4.7.1.1.7 | Columnds0BundleMapped | read-only | mandatory | This object indicates endpoint number as specified by mgEndpointNumber of endpoint table. If it is not associated with any endpoint, then it is set to -1. It s… |
| 1.3.6.1.4.1.351.110.4.7.1.1.8 | Columnds0IfType | read-only | mandatory | This object indicates the interface type associated with the ds0. ds0 ifType is considered as bearer if it the DS0 is used for carrying voice traffic. ds0 ifTy… |
| 1.3.6.1.4.1.351.110.4.7.1.1.9 | Columnds0CasVariantName | read-write | mandatory | This object indicates the index to the CAS variant table. This parameter can be configured after configuring this ds0 as an endpoint. This object cannot be mod… |
| 1.3.6.1.4.1.351.110.4.7.1.1.10 | Columnds0CasCadenceOnTime | read-write | mandatory | This attribute describes the duration during which the digit tone is generated. This object is applicable only for CAS backhaul applications. For trunking appl… |
| 1.3.6.1.4.1.351.110.4.7.1.1.11 | Columnds0CasCadenceOffTime | read-write | mandatory | This attribute corresponds to the silence between the digit tones. This object is applicable only for CAS backhaul applications. For trunking application it is… |
| 1.3.6.1.4.1.351.110.4.7.1.1.12 | Columnds0InsertLocalCas | read-write | mandatory | This object tells the framer whether to force the cas bits to a value defined by ds0LocalCasPattern or not. If this is enabled the framer will force the cas (A… |
| 1.3.6.1.4.1.351.110.4.7.1.1.13 | Columnds0LocalCasPattern | read-write | mandatory | This object contains the pattern that the cas (ABCD) bits will have when ds0InsertLocalCas is enabled. |
| 1.3.6.1.4.1.351.110.4.7.1.1.14 | Columnds0LoopbackCommand | read-write | mandatory | This object represents the loopback type at the ds0 level.The ds0 configuration overrides the line level configuration. NoLoop There is no loopback on this ds0… |
| 1.3.6.1.4.1.351.110.4.7.1.1.15 | Columnds0CasParameterSource | read-write | mandatory | This object indicates VISM whether to read the cas related timer parameters from the casAppl file downloaded for that endpoint or to read from this mib. This g… |
| 1.3.6.1.4.1.351.110.4.7.1.1.16 | Columnds0CasOnHookMinMakeTime | read-write | mandatory | This indicates the the minimum time in msecs for which the on hook pattern should be present in order for it to be recognised else the signal will be considere… |
| 1.3.6.1.4.1.351.110.4.7.1.1.17 | Columnds0CasOffHookMinMakeTime | read-write | mandatory | This indicates the minimum time in msecs for which the off hook pattern should be present in order for it to be recognised else the signal will be considered t… |
| 1.3.6.1.4.1.351.110.4.7.1.1.18 | Columnds0CasWinkMinMakeTime | read-write | mandatory | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.19 | Columnds0CasWinkMaxMakeTime | read-write | mandatory | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the maximum duration for which the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.20 | Columnds0CasWinkBreakTime | read-write | mandatory | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.21 | Columnds0CasGlareTime | read-write | mandatory | When the terminating gateway receives off Hook event from the Call Agent it starts the timer specified in this object to see if the terminating side is also tr… |
| 1.3.6.1.4.1.351.110.4.7.1.1.22 | Columnds0CasGaurdTime | read-write | mandatory | The gaurd time is the duration between the end of one call and the start of next call. This object specifies what should be such a duration. All state changes … |
| 1.3.6.1.4.1.351.110.4.7.1.1.23 | Columnds0CasDelayImmedStart | read-write | mandatory | This timer indicates the time that VISM should wait before outpulsing digits to the PBX after sending an off hook event. This applies only to immediate start p… |
| 1.3.6.1.4.1.351.110.4.7.1.1.24 | Columnds0SignalingType | read-only | mandatory | This attribute indicates the type of signaling on the line to which this ds0 belongs. CAS - Channel Associated Signaling CCS - Common Channel Signaling none - … |
| 1.3.6.1.4.1.351.110.4.7.1.1.25 | Columnds0CasMinDelayDialTime | read-write | mandatory | This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.26 | Columnds0CasMinStartDialTime | read-write | mandatory | This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.27 | Columnds0CasFlashMinMakeTime | read-write | mandatory | Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.28 | Columnds0CasFlashMaxMakeTime | read-write | mandatory | Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.29 | Columnds0CasDirectionality | read-write | mandatory | This object specifies the direction in which CAS calls will be accepted on this endpoint. If this object is set to incoming, then calls from the connected PBX … |
| 1.3.6.1.4.1.351.110.4.7.1.1.30 | Columnds0CasGlarePolicy | read-write | mandatory | This object specifies how a bidirectional endpoint should resolve glare. This object will be used only if dsx0VismDirectionality of the endpoint is bidirection… |
| 1.3.6.1.4.1.351.110.4.7.1.1.31 | Columnds0CasIncomingMgcpPackage | read-write | mandatory | This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like seize, disconnect, etc) related to an incom… |
| 1.3.6.1.4.1.351.110.4.7.1.1.32 | Columnds0CasOutgoingMgcpPackage | read-write | mandatory | This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like answer, disconnect, etc) related to an outg… |
| 1.3.6.1.4.1.351.110.4.7.1.1.33 | Columnds0InputGain | read-write | mandatory | This object indicates the amount of gain inserted at the receiver side of a ds0 channel, in dB (decibel) units. The default value of this object is 0 dB. The i… |
| 1.3.6.1.4.1.351.110.4.7.1.1.34 | Columnds0OutputAttenuation | read-write | mandatory | This object contains the amount of attenuation inserted at the transmit side of a ds0 channel, in dB (decibel) units. The output attenuation settings only defi… |
| 1.3.6.1.4.1.351.110.4.7.1.1.35 | Columnds0MusicThreshold | read-write | mandatory | The indicates Music On Hold Threshold in dBm. Based on this value, VISM DSP will interprete the incoming signal from TDM side as either silence or voice, and c… |
| 1.3.6.1.4.1.351.110.4.7.1.1.36 | Columnds0SidPacket | read-write | mandatory | This object specifies whether the Silence Indication Detection (SID) packet should be generated when silence suppression is in active mode. The SID packet indi… |
| 1.3.6.1.4.1.351.110.4.7.2 | Tabledsx0VismChanMapTable | not-accessible | mandatory | This table is created implicitly at the time of creating and deleting the endpoints. This table provides the mapping information from a line and channel to obt… |
| 1.3.6.1.4.1.351.110.4.7.2.1 | Rowdsx0VismChanMapEntry | not-accessible | mandatory | Please see the above description. |
| 1.3.6.1.4.1.351.110.4.7.2.1.1 | Columndsx1LineNum | read-only | mandatory | This object describes the physical line number on VISM card. |
| 1.3.6.1.4.1.351.110.4.7.2.1.2 | Columnds0ChanNum | read-only | mandatory | This object describes the ds0 number or channel number within a T1 or E1 line. The valid channel numbers are 1 to 24 for T1 line and 1 - 31 for E1 line. |
| 1.3.6.1.4.1.351.110.4.7.2.1.3 | Columnds0ChanMapIfIndex | read-only | mandatory | This object describes the ifIndex derived based on the line number and the channel number within the line according to the formula: IfIndex = 31 * (Ds1# - 1) +… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1 | NodefrPortCnfPortGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1 | TablefrPortCnfPortGrpTable | not-accessible | mandatory | The config table is for logical port interface. In FRSM-VHS, there are upto 256 entries for FRSM-2CT3 card and 2 entries for FRSM-T3/E3/HS2/T3B/E3B/HS2B-HSSI c… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1 | RowfrPortCnfPortGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.1 | ColumnportNum | read-only | mandatory | This is logical port number. If we have T1 card then the maximum port number is 192 and if we have E1 card the maximum port number can be 248. For FRSM-2CT3 ca… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.2 | ColumnportLineNum | read-write | mandatory | This represents the line number For FRSM12 card: The ifIndex of the physical line on which this port is provisioned. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.3 | ColumnportRowStatus | read-write | mandatory | This variable enables or modifies the port 1- add 2 - del 3 - mod For FRSM12 card: For Snmp GET operations, only mod is returned. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.4 | ColumnportDs0ConfigBitMap | read-write | mandatory | This respesents bit map of DS0s for a line which are used to form this logical port. Bit 0 represents DS0-1. This entry is not used for unchannelized FRSM-VHS/… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.5 | ColumnportDs0Speed | read-write | mandatory | This represents port speed of 64 or 56 1 - speed56k 2 - speed64k 3 - unUsed. This field is not used for unchannelised FRSM-VHS (FRSM-2T3/ FRSM-2E3/FRSM-HS2/FRS… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.6 | ColumnportFlagsBetweenFrames | read-write | mandatory | Number of flags transmitted between FR frames For FRSM12 card: Only the values 1 to 8 are supported. The mapping is as follows: MIB object value No. of HDLC fl… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.7 | ColumnportEqueueServiceRatio | read-write | mandatory | Number of times queue 1 is serviced for every time queue 2 is serviced. The value 0 is supported only by FRSM-VHS. FRSM-VHS supports two different egress queue… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.8 | ColumnportSpeed | read-only | mandatory | Configured speed of port in kbps |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.9 | ColumnportAdmin | read-write | mandatory | used to up and down the port For FRSM12 card: This variable will be equivalent to ifAdminStatus of of ifTable. The write-only is not used. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.10 | ColumnportType | read-write | mandatory | This represents port type For FRSM12 card: frFUNI not Applicable. For frame-relay the ifType is frameRelayService(44) and for frame-forward it is frForward(158… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.11 | ColumnportSvcStatus | read-write | mandatory | This represents SVC status For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.12 | ColumnportSvcInUse | read-write | mandatory | This represents port svc in use For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.13 | ColumnportSvcShareLcn | read-only | mandatory | This represents port type For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.14 | ColumnportSvcLcnLow | read-only | mandatory | This represents low end of reserved LCN for svc For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.15 | ColumnportSvcLcnHigh | read-only | mandatory | This represents high end of reserved LCN for svc For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.16 | ColumnportSvcDlciLow | read-only | mandatory | This represents low end of reserved DLCI for svc For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.17 | ColumnportSvcDlciHigh | read-only | mandatory | This represents high end of reserved DLCI for svc For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.18 | ColumnportDeleteSvcs | read-write | mandatory | Setting this object to 1 indicates that all the SVC connections on the given port has to be deleted For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.19 | ColumnportIngrSvcBandW | read-only | mandatory | This represents Ingress Bandwidth reserve for SVC For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.20 | ColumnportEgrSvcBandW | read-only | mandatory | This represents Egress Bandwidth reserve for SVC For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.21 | ColumnportBERTEnable | read-write | mandatory | This variable enables BERT For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.22 | ColumnportEnhancedSIW | read-write | mandatory | This variable enables/disables enhanced SIW feature. Enabling this permits support for SIW translation of Appletalk. This feature is currently supported only i… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.23 | ColumnportM32EgrQueueThresh | read-write | mandatory | This represents the M32 logical port Egress Queue threshold in bytes. Frames will not be queued until the number of bytes in the queue is less than the thresho… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.24 | ColumnportHeaderLen | read-write | mandatory | This object is added for FRSM12. The value of this object identifies the Q.922 Address field length and DLCI length for this UNI/NNI logical port. This object … |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.25 | ColumnportFrameChkSumType | read-write | mandatory | This object is added for FRSM12. The value of this object identifies the CRC Length in the HDLC Packet. Applicable for FrameForwarding ports only. This object … |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.26 | ColumnportFileId | read-write | mandatory | The ID of the SCT file that holds module specific configuration parameters for this FR virtual interface. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.27 | ColumnportOverSubEnable | read-write | mandatory | This object is added for FRSM12. When this object is enabled the port will be allowed to be over subscribed. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.2 | ScalarportsUsedLine1 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.3 | ScalarportsUsedLine2 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.4 | ScalarportsUsedLine3 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.5 | ScalarportsUsedLine4 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.6 | ScalarportNextAvailable | read-only | mandatory | This variable contains the next UNUSED logical port number. This number can be used in channel config table, the portNextAvailable gets updated if the number g… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.7 | ScalarportsUsedLine5 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.8 | ScalarportsUsedLine6 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.9 | ScalarportsUsedLine7 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.10 | ScalarportsUsedLine8 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11 | TablefrPortsUsedLineGrpTable | not-accessible | mandatory | Contains a sequence of entries for each DS1 line. each entry gives the number of DS0 slots being used added for FRSM_VHS |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1 | RowfrPortsUsedLineGrpEntry | not-accessible | mandatory | One entry per DS1 |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1.1 | ColumnfrPortsUsedLineIndex | read-only | mandatory | This is the Index to the table containing the portsUsedLine for the 56 DS1s |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1.2 | ColumnfrPortsUsedLine | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1 | NodefrPortCnfSigLMIGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1 | TablefrPortCnfSigLMIGrpTable | not-accessible | mandatory | The config table is for logical port interface there are upto 248 entries (8 E1s) and 192 entries (8 T1s). In FRSM-VHS, there are a total of 256 entries. In FR… |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1 | RowfrPortCnfSigLMIGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.1 | ColumnlmiCnfPortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.2 | ColumnsignallingProtocolType | read-write | mandatory | This will set the signalling protocol 1 - other 2 - noSignalling 3 - strataLMI 4 - annexAUNI 5 - annexDUNI 6 - annexANNI 7 - annexDNNI Only noSignalling is app… |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.3 | ColumnasynchronousUpdates | read-write | mandatory | disable - disable Asynchronous Status Updates & Unsolicited Full Status enable - enable Asynchronous Status Updates fsenable - enable Unsolicited Full Status u… |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.4 | Columnt391LinkIntegrityTimer | read-write | mandatory | Interval in seconds for NNI to do status polling The signalling parameters are not applicable for the frame forwarding port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.5 | Columnt392PollingVerificationTimer | read-write | mandatory | Interval in seconds for UNI to expect status polling The signalling parameters are not applicable for the frame forwarding port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.6 | Columnn391FullStatusPollingCounter | read-write | mandatory | Number of UNI/NNI Polling cycles The signalling parameters are not applicable for the frame forwarding port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.7 | Columnn392ErrorThreshold | read-write | mandatory | UNI/NNI Error Threshold The signalling parameters are not applicable for the frame forwarding port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.8 | Columnn393MonitoredEventCount | read-write | mandatory | UNI/NNI Events, always greater than n392 The signalling parameters are not applicable for the frame forwarding port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.9 | ColumnenhancedLmi | read-write | mandatory | This object defines if enhanced LMI is enabled on a logical port. The signalling parameters are not applicable for the frame forwarding port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.1.1.1.10 | ColumnportFRF1Dot2Support | read-write | mandatory | This object is added for FRSM12. This variable enables/disables FRF 1.2 feature. This object is not applicable to MGX Release 1.x |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2 | NodefrPortCnfSigCLLMGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2.1 | TablefrPortCnfSigCLLMGrpTable | not-accessible | mandatory | The config table is for logical port interface |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2.1.1 | RowfrPortCnfSigCLLMGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2.1.1.1 | ColumncllmCnfPortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2.1.1.2 | ColumncllmEnable | read-write | mandatory | This will enable CLLM 1 - disabled 2 - enabled CLLM is not applicable for frame forwarding ports |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2.1.1.3 | ColumnxmtCLLMStatusTimer | read-write | mandatory | Interval in milliseconds for CLLM to send CLLM updates CLLM parameters are not applicable for frame forwarding ports |
| 1.3.6.1.4.1.351.110.5.1.1.1.2.2.1.1.4 | ColumnrcvCLLMStatusTimer | read-only | mandatory | Timeout value for receiving CLLM updates CLLM parameters are not applicable for frame forwarding ports |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1 | TablefrPortCnfX21PortGrpTable | not-accessible | mandatory | The config table is for X.21/HSSI logical port interface |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1 | RowfrPortCnfX21PortGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.1 | Columnx21portNum | read-only | mandatory | This is logical port number. The HSSI backcard can support upto 3 ports, whereas the X.21 can support 4 logical ports. No defaults. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.2 | Columnx21portLineNum | read-write | mandatory | This represents the line number. On FRSM-HS1 the HSSI can support 3 lines and X.21 4 lines. No defaults. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.3 | Columnx21portRowStatus | read-write | mandatory | This variable adds, deletes, or modifies the port 1- add 2 - delete 3 - modify Default is add. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.4 | Columnx21portFlagsBetweenFrames | read-write | mandatory | Number of flags transmitted between two consecutive HDLC frames. Default is 1 flag. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.5 | Columnx21portEqueueServiceRatio | read-write | mandatory | Number of times queue 1 is serviced for every time queue 2 is serviced. Default is 1. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.6 | Columnx21portSpeed | read-only | mandatory | Port speed in kbps. At present it is same as line speed. No defaults. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.7 | Columnx21portAdmin | read-write | mandatory | Up/down used to up and down the port. Default is the up state. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.8 | Columnx21portType | read-write | mandatory | This represents port type. The processing of the frames depends on the type of the port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.9 | Columnx21portSvcStatus | read-write | mandatory | This represents SVC status |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.10 | Columnx21portSvcInUse | read-write | mandatory | This represents port svc in use |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.11 | Columnx21portSvcShareLcn | read-only | mandatory | This represents port type |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.12 | Columnx21portSvcLcnLow | read-only | mandatory | This represents low end of reserved LCN for svc |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.13 | Columnx21portSvcLcnHigh | read-only | mandatory | This represents high end of reserved LCN for svc |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.14 | Columnx21portSvcDlciLow | read-only | mandatory | This represents low end of reserved DLCI for svc |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.15 | Columnx21portSvcDlciHigh | read-only | mandatory | This represents high end of reserved DLCI for svc |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.16 | Columnx21portDeleteSvcs | read-write | mandatory | Setting this object to 1 indicates that all the SVC connections on the given port has to be deleted |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.17 | Columnx21portIngrSvcBandW | read-only | mandatory | This represents Ingress Bandwidth reserve for SVC |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.18 | Columnx21portEgrSvcBandW | read-only | mandatory | This represents Egress Bandwidth reserve for SVC |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1 | TablefrPortServiceQueGrpTable | not-accessible | mandatory | The config table is for logical port interface. In FRSM-VHS, there are 256 entries for FRSM-2CT3 card and 2 entries for FRSM-T3/E3/HS2/T3B/E3B/HS2B-HSSI cards … |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1 | RowfrPortServiceQueGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.1 | ColumnfrServPortNum | read-only | mandatory | This is the logical port number. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.2 | ColumnportServiceQueueNo | read-write | mandatory | This identifies the Q depending on the Service Type 1 High Priority Queue 2 rt VBR Queue 3 nrt VBR and ABR Queue 4 UBR Queue queue5(5) to queue8(8) are reserve… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.3 | ColumnportEgresQDepth | read-write | mandatory | Indicates the peak Egress queue depth for the logical port. The total queue depth of all connections mapped to this queue should not exceed this value. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.4 | ColumnportEgresECNThresh | read-write | mandatory | ECN threshold for the logical port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, then the appropriate ECN bit … |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.5 | ColumnportEgresDEThresh | read-write | mandatory | DE threshold for the logical port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, and the DE bit is set in the i… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.6 | ColumnportQBwInc | read-only | mandatory | Denotes the bandwidth increment for this port queue. The bandwidth increment is the percentage of the port bandwidth used by all connections mapped to a partic… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.7 | ColumnportBytesDiscXceedQueFull | read-only | mandatory | Counter maintained for the no of bytes discarded due to port queue depth exceeded. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.8 | ColumnportBytesDiscXceedDEThresh | read-only | mandatory | Counter maintained for the no of bytes discarded due to DE threshold exceeded. |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1 | TablefrPortCnfResPartGrpTable | not-accessible | mandatory | This table contains the configuration of port resource partition |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1 | RowfrPortCnfResPartGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.1 | ColumnfrResPartPortNum | read-only | mandatory | This is the logical port number, the index to this table. If we have T1 card then the maximum port number is 192 and if we have E1 card the maximum port number… |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.2 | ColumnfrResPartCtrlrNum | read-only | mandatory | This is index for controller using the port In MGX release 1.0, the value par should be used In MGX release 2.0, the value pnni should be used |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.3 | ColumnfrResPartRowStatus | read-write | mandatory | This will add, delete or modify the partition. In MGX Release1.0: To add an entry, this object should be set to add, value for other objects should not be spec… |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.4 | ColumnfrResPartNumOfLcnAvail | read-write | mandatory | This represents number of LCNs available for this controller and this port FRSM VHS 2CT3 can support LCNs upto 4000. FRSM12 can support LCNs upto 16000. |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.5 | ColumnfrResPartDlciLow | read-write | mandatory | This represents low end of reserved DLCI |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.6 | ColumnfrResPartDlciHigh | read-write | mandatory | This represents high end of reserved DLCI |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.7 | ColumnfrResPartIngrPctBW | read-write | mandatory | The percentage of total ingress bandwidth reserved |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.8 | ColumnfrResPartEgrPctBW | read-write | mandatory | The percentage of total egress bandwidth reserved |
| 1.3.6.1.4.1.351.110.5.1.1.1.5.1.1.9 | ColumnfrResPartCtrlrID | read-write | mandatory | This is the controller identifier for the resource patition. The default value is set for PNNI controller. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1 | NodefrPortCntPortGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1 | TablefrPortCntPortGrpTable | not-accessible | mandatory | The config table is for logical port interface there are upto 248 entries (for 8 E1s) or 192 (for 8 T1s). In FRSM-VHS, there is support for upto 256 entries. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1 | RowfrPortCntPortGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.1 | ColumncntPortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.2 | ColumnrcvPortFrames | read-only | mandatory | The number of frames Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.3 | ColumnrcvPortBytes | read-only | mandatory | The number of bytes Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.4 | ColumnrcvPortFramesDE | read-only | mandatory | The number of frames with DE bit set Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.5 | ColumnrcvPortFramesFECN | read-only | mandatory | The number of frames with FECN bit set Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.6 | ColumnrcvPortFramesBECN | read-only | mandatory | The number of frames with BECN bit set Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.7 | ColumnrcvFramesDiscCRCError | read-only | mandatory | The number of frames discarded on the ingress due to CRC error |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.8 | ColumnrcvFramesDiscAlignmentError | read-only | mandatory | The number of frames discarded on the ingress due to Alignment error |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.9 | ColumnrcvFramesDiscIllegalLen | read-only | mandatory | The number of frames discarded on the ingress due to illegal length |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.10 | ColumnrcvFramesDiscIllegalHeader | read-only | mandatory | The number of frames discarded on the ingress due to illegal header |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.11 | ColumnrcvFramesAbort | read-only | mandatory | The number of received frames aborted |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.12 | ColumnrcvFramesUnknownDLCI | read-only | mandatory | The number of frames received with an unknown DLCI |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.13 | ColumnrcvLastUnknownDLCI | read-only | mandatory | The last unknown DLCI received |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.14 | ColumnrcvPortFramesTaggedFECN | read-only | mandatory | The number of frames received that were tagged with FECN bit |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.15 | ColumnrcvPortFramesTaggedBECN | read-only | mandatory | The number of frames received that were tagged with BECN bit |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.16 | ColumnrcvPortFramesTaggedDE | read-only | mandatory | The number of frames received that were tagged with DE bit |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.17 | ColumnrcvPortFramesDiscXceedDEThresh | read-only | mandatory | The number of frames discarded on the ingress due to exceeded DE Threshold |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.18 | ColumnrcvPortKbpsAIR | read-only | mandatory | Received Average Information Rate in KBPS |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.19 | ColumnrcvBufNotAvailable | read-only | mandatory | The number of times the receiver is turned off |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.20 | ColumnxmtPortFrames | read-only | mandatory | The number of frames transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.21 | ColumnxmtPortBytes | read-only | mandatory | The number of bytes transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.22 | ColumnxmtPortFramesFECN | read-only | mandatory | The number of frames transmittedc with FECN bit already set |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.23 | ColumnxmtPortFramesBECN | read-only | mandatory | The number of frames transmitted with BECN bit already set |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.24 | ColumnxmtPortFramesDiscXceedQDepth | read-only | mandatory | The number of frames discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.25 | ColumnxmtPortBytesDiscXceedQDepth | read-only | mandatory | The number of bytes discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.26 | ColumnxmtPortFramesDuringLMIAlarm | read-only | mandatory | The number of frames transmitted during LMI logical port alarm |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.27 | ColumnxmtPortBytesDuringLMIAlarm | read-only | mandatory | The number of bytes transmitted during LMI logical port alarm |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.28 | ColumnxmtFramesAbort | read-only | mandatory | The number of transmit frames aborted For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.29 | ColumnxmtFramesUnderrun | read-only | mandatory | The number of frames discarded due to underrun |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.30 | ColumnxmtPortKbpsAIR | read-only | mandatory | Transmit Average Information Rate in KBPS |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.31 | ColumnxmtBufNotAvailable | read-only | mandatory | The number of times the transmitter is turned off For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.32 | ColumnportClrButton | read-write | mandatory | Port clear button. Resets all counters. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.33 | ColumnrcvFramesDiscNoChan | read-only | mandatory | The number of frames received when no channel is setup |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.34 | ColumnrcvFramesDiscOverrun | read-only | mandatory | The number of frames discarded in Ingress direction due to FIFO overrun in HDLC Controller. This object is not applicable to MGX Release 1.x |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1 | NodefrPortCntSigLMIGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1 | TablefrPortCntSigLMIGrpTable | not-accessible | mandatory | The LMI counter table is for logical port interface there are upto 248 entries (for 8 E1s) and upto 192 entries (for 8 T1s). In FRSM-VHS, there are upto 256 en… |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1 | RowfrPortCntSigLMIGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.1 | ColumnlmiSigPortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.2 | ColumnrcvStatusInquiry | read-only | mandatory | The number of Status Inquiry messages received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.3 | ColumnrcvInvalidRequest | read-only | mandatory | The number of Invalid Request messages received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.4 | ColumnrcvUNISeqMismatch | read-only | mandatory | The number of times UNI messages with sequence number mismatches were received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.5 | ColumnxmtStatus | read-only | mandatory | The number of times Status response messages transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.6 | ColumnxmtAsynchUpdate | read-only | mandatory | The number of times Asynch Status messages transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.7 | ColumnuniSignalingTimeout | read-only | mandatory | The number of times UNI Status requests were not received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.8 | ColumnxmtStatusInquiry | read-only | mandatory | The number of Status Inquiry messages transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.9 | ColumnrcvStatus | read-only | mandatory | The number of times Status response messages received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.10 | ColumnrcvAsynchUpdate | read-only | mandatory | The number of times Asynch Status messages received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.11 | ColumnrcvNNISeqMismatch | read-only | mandatory | The number of times NNI messages with sequence number mismatches were received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.1.1.1.12 | ColumnnniSignalingTimeout | read-only | mandatory | The number of times NNI Status requests were not received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2 | NodefrPortCntSigCLLMGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1 | TablefrPortCntSigCLLMGrpTable | not-accessible | mandatory | The CLLM counter table is for logical port interface |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1 | RowfrPortCntSigCLLMGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1.1 | ColumncllmSigPortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1.2 | ColumnrcvFramesCLLM | read-only | mandatory | The number of CLLM frames received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1.3 | ColumnrcvBytesCLLM | read-only | mandatory | The number of CLLM bytes received |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1.4 | ColumnxmtFramesCLLM | read-only | mandatory | The number of CLLM frames transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1.5 | ColumnxmtBytesCLLM | read-only | mandatory | The number of CLLM bytes transmitted |
| 1.3.6.1.4.1.351.110.5.1.1.2.2.2.1.1.6 | ColumncllmFailures | read-only | mandatory | The number of times an expected CLLM message was not received |
| 1.3.6.1.4.1.351.110.5.1.1.3 | NodefrPortStateGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.3.1 | TablefrPortStateGrpTable | not-accessible | mandatory | Table of transmit/receive states of ports. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1 | RowfrPortStateGrpEntry | not-accessible | mandatory | An entry for logical port. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.1 | ColumnstatePortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.2 | ColumnportState | read-only | mandatory | This variable indicates the state of the logical port |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.3 | ColumnportSignallingState | read-only | mandatory | Bit 0 = 0 -> LMI O.K. or not enabled Bit 0 = 1 -> LMI failed Bit 1 = 0 -> CLLM O.K. or not enabled Bit 1 = 1 -> CLLM failed |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.4 | ColumnportOversubscribed | read-only | mandatory | This variable indicates the whether the port is over subscribed or not |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.5 | ColumnportIngrPercentUtil | read-only | mandatory | Percentage Utilization of the Port in the Ingress direction. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.6 | ColumnportEgrPercentUtil | read-only | mandatory | Percentage Utilization of the Port in the Egress direction. |
| 1.3.6.1.4.1.351.110.5.1.2.1 | NodefrChanCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.1.2.1.1 | TablefrChanCnfGrpTable | not-accessible | mandatory | The config table is for logical channel interface (upto 4000 entries). The actual number of entries supported by a card depends on the type of card. eg: FRSM-4… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1 | RowfrChanCnfGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.1 | ColumnchanNum | read-only | mandatory | Refers to the virtual connection index Note that the actual range of the index supported by a card depends on the type of card. eg: FRSM-4T1/E1 supports a rang… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.2 | ColumnchanRowStatus | read-write | mandatory | This will add, delete or modify the channel 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY Setting this object to outOfService takes the channel out of service or brings … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.3 | ColumnchanPortNum | read-write | mandatory | Refers to the logical ports that are possible on this card, the user must set this variable For FRSM12 Card: This object contains the port's ifIndex value. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.4 | ColumndLCI | read-write | mandatory | This variable is the DLCI number of the channel. The user has to set this variable. All the connections on the same port should have a unique DLCI number. Note… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.5 | ColumnegressQSelect | read-write | mandatory | Selects one out of two possible port queues. The default port queue number is 1 which is the high pririty queue. 1 = High priority queue 2 = Low priority queue… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.6 | ColumningressQDepth | read-write | mandatory | This variable sets the max depth for queue, before it starts dropping the cells. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.7 | ColumningressQECNThresh | read-write | mandatory | This variable sets the max depth for queue, before it starts flow control. It is defined in terms of number of bytes. In all cards except the FRSM-VHS card, th… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.8 | ColumningressQDEThresh | read-write | mandatory | This variable sets the max depth for queue, before they become discard eligible. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.9 | ColumnegressQDepth | read-write | mandatory | This variable sets the max depth for queue, before it starts dropping the cells. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.10 | ColumnegressQDEThresh | read-write | mandatory | This variable sets the max depth for queue, before they become discard eligible. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.11 | ColumnegressQECNThresh | read-write | mandatory | This variable sets the max depth for queue, before it starts flow control. It is defined in terms of number of bytes. In all cards except the FRSM-VHS card, th… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.12 | ColumndeTaggingEnable | read-write | mandatory | The default value is 2. This variable enables DE tagging in the ingress direction only. enable = 1 disable = 2 For FRSM12 Card: When this object is disabled, t… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.13 | Columncir | read-write | mandatory | The default value is 2400 cir defines committed information rate cir is in bits per second Maximum value for cir for an E1 card is 2048000 and for a T1 card is… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.14 | Columnbc | read-write | mandatory | The default value is 5100 bc defines burst committed. bc is in bytes. bc can not be 0 when cir is not 0. bc has to be 0 if cir is 0. The peak value for bc in F… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.15 | Columnbe | read-write | mandatory | The default value is 5100 be defines the burst excess. be can not be 0 when cir is 0. be is in bytes. The peak value for be in FRSM-VHS cards is (2^21 -1), i.e… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.16 | Columnibs | read-write | mandatory | The default value is 100 ibs should be less or equal to bc when cir is greater than 0. ibs has to be 0 when cir is 0. The peak value for ibs in FRSM-VHS cards … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.17 | ColumnforeSightEnable | read-write | mandatory | The default value is 2 This variable sets foreSight option Note that when you enable foresight option then you can modify qir, mir and pir, otherwise you CAN N… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.18 | Columnqir | read-write | mandatory | The dafault is 160 qir is defined in fastpackets/sec and it defines quiescent information rate for Foresight. 1 cell/sec is equal to 16 fastpackets/sec. Follow… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.19 | Columnmir | read-write | mandatory | The dafault is 160 mir is defined in fastpackets/sec and it defines minimum information rate for Foresight. 1 cell/sec is equal to 16 fastpackets/sec. Followin… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.20 | Columnpir | read-write | mandatory | The dafault is 160 pir is defined in fastpackets/sec and it defines peak information rate for Foresight. 1 cell/sec is equal to 16 fastpackets/sec. Following i… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.21 | ColumnchanLocRmtLpbkState | read-write | mandatory | The default is disable. This variable enables or disables the remote loopback for each channel. When you enable this option on a connection (channel) then all … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.22 | ColumnchanTestType | read-write | mandatory | The default is notest. The chanTestType starts testing the continuity or delay of a connection. It sends specific cell patterns toward the network and the term… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.23 | ColumnchanTestState | read-only | mandatory | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.24 | ColumnchanRTDResult | read-only | mandatory | This is round trip delay in milliseconds. When you select testdelay option for the chanTestType, the result of the test that is measured in milliseconds can be… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.25 | ColumnchanType | read-write | mandatory | sets channel type Type 1 is frame-relay network interworking (NIW-unicast) type 2 is service interworking with out any SDU translation type 3 is service interw… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.26 | ColumnchanFECNconfig | read-write | mandatory | sets FECN config mapEFCI valid only for SIW The FECN bits in frame-relay are mapped to EFCI bit in the ATM cells. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.27 | ColumnchanDEtoCLPmap | read-write | mandatory | sets mapping of CLP bit The DE bit is mapped to CLP bit in ATM cell in Case 2 and 3, the DE bit is ignored and CLP bit is set to a constant value For FRSM12 Ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.28 | ColumnchanCLPtoDEmap | read-write | mandatory | sets mapping of DE bit 1,2,3 valid for SIW 1,4 valid for NIW The CLP bit is mapped to DE bit in frame-relay in the Case of 2 and 3, the CLP bit is ignored and … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.29 | ColumnchanIngrPercentUtil | read-write | mandatory | the channel ingress utilized percentage |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.30 | ColumnchanEgrPercentUtil | read-write | mandatory | the channel egress utilized percentage |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.31 | ColumnchanEgrSrvRate | read-write | mandatory | The channel egress cir. Maximum value for chanEgrSrvRate for an E1 card is 2048000 and for a T1 card is 1536000. chanEgrSrvRate has to be less than or equal to… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.32 | ColumnchanOvrSubOvrRide | read-write | mandatory | This MIB variable allows one to add a new connection on a port even if it is over subscribed. For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.33 | ColumnchanFrConnType | read-write | mandatory | channel connection type 1 for pvc 2 for svc 3 for spvc 4 par (only for trunk connection) 5 pnni (only for trunk connection) 6 tag (only for trunk connection) F… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.34 | ColumnfrCDRNumber | read-write | mandatory | This is the key to correlate cell/frame counts, start/end record. For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.35 | ColumnfrLocalVpi | read-only | mandatory | This VPI together with the local VCI and NSAP represents the local end point in this connection, this object is read only, therefore it'll be assigned by SM to… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.36 | ColumnfrLocalVci | read-only | mandatory | This VCI together with the local VPI and NSAP represents the local end point in this connection, this object is read only, therefore it'll be assigned by SM to… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.37 | ColumnfrLocalNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 1 byte rsvd, 3 bytes for logical interface: slot (1 byte) and por… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.38 | ColumnfrRemoteVpi | read-write | mandatory | This VPI together with the remote VCI and NSAP represents the remote end point in this connection |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.39 | ColumnfrRemoteVci | read-write | mandatory | This VCI together with the remote VPI and NSAP represents the remote end point in this connection |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.40 | ColumnfrRemoteNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 1 byte rsvd, 3 bytes for logical interface: slot (1 byte) and por… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.41 | ColumnfrMastership | read-write | mandatory | This is used by PXM to determine if this end point is master or slave, a new type unknown is added to identify the SM in AXIS shelf and the SM in MGX shelf. In… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.42 | ColumnfrVpcFlag | read-write | mandatory | This represents the connection type, used for PXM to identify VPC/VCC but FRSM card doesn't use it always set to vcc for FRSM card For FRSM12 Card: This object… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43 | ColumnfrConnServiceType | read-write | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.44 | ColumnfrRoutingPriority | read-write | mandatory | This is used by PXM to determine how important this connection is when selecting connections to route |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.45 | ColumnfrMaxCost | read-write | mandatory | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. T… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.46 | ColumnfrRestrictTrunkType | read-write | mandatory | Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.47 | ColumnfrConnPCR | read-write | mandatory | Peak cell rate, if not provided in the connection setup request, it'll be derived from pir. For FRSM12 Card: Default value is (1.44 * CIR) |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.48 | ColumnfrConnRemotePCR | read-write | mandatory | Peak cell rate of the other end, if not set, will be set to the same as local end PCR (frConnPCR). However, note that if the CIRs for both local and remote end… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.49 | ColumnfrConnMCR | read-write | mandatory | Minimum cell rate, if not provided in the connection setup request, it'll be derived from mir. For FRSM12 Card: Default value is frConnPCR |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.50 | ColumnfrConnRemoteMCR | read-write | mandatory | Minimum cell rate of the other end, if not set, will be set to the same as local end MCR (frConnMCR). However, note that if the CIRs for both local and remote … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.51 | ColumnfrConnPercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by this end-point. If this is not specified in the connection setup request, it'll be defaulted to 10… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.52 | ColumnfrConnRemotePercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by the other end-point. If this is not specified in the connection setup request, it'll be set to be … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.53 | ColumnfrConnForeSightEnable | read-write | mandatory | This object is used by the controller(PAR/PNNI/TAG) to set up the Qbin for the connection, if this is not set, it'll be defaulted by SM to the same as foreSigh… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.54 | ColumnfrConnFGCRAEnable | read-write | mandatory | enables/disables Frame based GCRA (early packet discard). For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.55 | ColumnchanServType | read-write | mandatory | This indicates the class of the connection 1-High priority (typically CBR connections) 2- real-time VBR 3- non-real time VBR 4- Available Bit Rate 5- Unspecifi… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.56 | ColumnchanServiceRateOverride | read-write | mandatory | This variable sets the SAR IR programming option. Foresight and chanServiceRateOverride are mutually exclusive. For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.57 | ColumnchanServiceRate | read-write | mandatory | This is the rate to which IR can be set to when chanServiceRateOverride is set to enabled. If chanServiceRateOverride is disabled then this object does not hav… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.58 | ColumnzeroCirConEir | read-write | mandatory | zeroCirConEir defines EIR value for '0' CIR connection. If zeroCirConEir is '0', EIR is set to port speed. If zeroCirConEir is non-zero value, EIR is set to va… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.59 | ColumnchanReroute | read-write | mandatory | This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to fals… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.60 | ColumnfrConnSCR | read-write | mandatory | Sustained cell rate, Used for VBR connections setup with PNNI controller. For FRSM12 Card: Default value is frConnPCR This object is not applicable to MGX Rele… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.61 | ColumnfrConnRemoteSCR | read-write | mandatory | Sustained cell rate of the other end, Used for VBR connections setup with PNNI controller. For FRSM12 Card: Default value is frConnSCR This object is not appli… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.62 | ColumnfrConnTemplateId | read-write | mandatory | This object specifies the template identifier for the connection template associated with this connection. The valid range for templates is 1..16. A value of 1… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.63 | ColumnfrConnAdminStatus | read-write | mandatory | This object specifies channel admin status. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.64 | ColumnfrChanCnfChangeCount | read-only | mandatory | This object is added only for FRSM12 card. This counter tracks the number of configuration changes that happen on a channel. The counter is associated only wit… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.65 | ColumnfrChanCnfIgnoreIncomingDE | read-write | mandatory | This object is added for FRSM12 card. When this object is enabled, the incoming frames with DE(Discard Eligible) bit set to 1 are counted in the Bc bucket inst… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.66 | ColumnfrChanOamCCEnable | read-write | mandatory | This object is added for FRSM12 card. This object serves to enable or disable continuity check(CC) on a connection endpoint. When continuity check is enabled o… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.67 | ColumnfrChanStatsEnable | read-write | mandatory | This object is added for FRSM12 card. Limits imposed by software or hardware implementations could restrict the amount of statistical data that can be maintain… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.68 | ColumnfrChanLocalLpbkEnable | read-write | mandatory | This object is added for FRSM12 card. This object when enabled adds a channel-level loopback towards the port side. If the connection is in loopback, Connectio… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.69 | ColumnfrChanUpcEnable | read-write | mandatory | This object is added for FRSM12 card. This object when disabled, disables Frame Relay policing. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.70 | ColumnfrChanSlaveType | read-write | mandatory | This object is added for FRSM12 card. This object indicates whether a master endpoint has a persistent slave or not. A connection with a master and a non-persi… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.71 | ColumnfrConnRemoteMBS | read-write | mandatory | Remote Maximum Burst Size in terms of number of cells. This object should be set by the user in cases when the remote end of the connection is an ATM end-point… |
| 1.3.6.1.4.1.351.110.5.1.2.1.2 | ScalarchanNumNextAvailable | read-only | mandatory | This variable contains the next UNUSED channel number of the possible 4000 (ranging from 16 to 4015). This number can be used in channel config table, the Chan… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3 | TablefrstdABRCnfGrpTable | not-accessible | mandatory | The ABR config table is for logical channel interface (upto 4000 entries). The actual number of entries supported by a card depends on the type of card. eg: FR… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1 | RowfrstdABRCnfGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.1 | ColumnfrstdABRcnfChanNum | read-only | mandatory | Refers to the virtual connection index Note that the actual range of the index supported by a card depends on the type of card. eg: FRSM-4T1/E1 supports a rang… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.2 | ColumnfrstdABRTBE | read-write | mandatory | Transient Buffer Exposure. The unit is number of cells. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.3 | ColumnfrstdABRFRTT | read-write | mandatory | Fixed Round-Trip Time. The unit is milliseconds. Value 0 signifies that FRTT is not available. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.4 | ColumnfrstdABRRDF | read-write | mandatory | Rate Decrease Factor. This unitless value has to be inverted to arrive at the actual value. The valid values possible are only powers of 2; i.e. 1, 2, 4, 8 ...… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.5 | ColumnfrstdABRRIF | read-write | mandatory | Rate Increase Factor. This unitless value has to be inverted to arrive at the actual value. The valid values possible are only powers of 2; i.e. 1, 2, 4, 8 ...… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.6 | ColumnfrstdABRNrm | read-write | mandatory | Maximum number of cells a source may send for each forward RM cell. The valid values possible are only powers of 2 starting from 2; i.e. 2, 4, 8 ..... 256. The… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.7 | ColumnfrstdABRTrm | read-write | mandatory | Upper bound on the time between forward RM cells for an active source. The unit is in milliseconds. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.8 | ColumnfrstdABRCDF | read-write | mandatory | Cutoff Decrease Factor. This unitless value has to be inverted to arrive at the actual value. The valid values possible are 0 and only powers of 2; i.e., 1, 2,… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.9 | ColumnfrstdABRADTF | read-write | mandatory | ACR DecreaseTime Factor. Unit of this value is milliseconds. Granularity allowed is 10 milli seconds. The SNMP agent has to verify this compliance. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.10 | ColumnfrstdABRICR | read-write | mandatory | Initial Cell Rate is the rate at which the source should send initially and after an idle period. This includes the bandwidth allocated for both data cells as … |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.11 | ColumnfrstdABRMCR | read-write | mandatory | Minimum Cell Rate is the rate at which the source is allowed to send. This includes the bandwidth allocated for both data cells as well as all in-rate RM cells… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.12 | ColumnfrstdABRPCR | read-write | mandatory | Peak Cell Rate is the rate at which the source is allowed to send. This includes the bandwidth allocated for both data cells as well as all in-rate RM cells. U… |
| 1.3.6.1.4.1.351.110.5.1.2.2 | NodefrChanStateGrp | |||
| 1.3.6.1.4.1.351.110.5.1.2.2.1 | TablefrChanStateGrpTable | not-accessible | mandatory | Table of transmit/receive states of channels. |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1 | RowfrChanStateGrpEntry | not-accessible | mandatory | An entry for FrChannelStateGrpEntry. |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.1 | ColumnstateChanNum | read-only | mandatory | Refers to the virtual connection index Note that the actual range of the index supported by a card depends on the type of card. eg: FRSM-4T1/E1 supports a rang… |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.2 | ColumnchanState | read-only | mandatory | This variable indicates the LMI state of the VC (channel) failed(4) is added to distinguish between alarm (when the connection in the PNNI n/w is not actually … |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.3 | ColumnxmtAbitState | read-only | mandatory | The A bit transmit state 1 - LMI off 2 - LMI on and connection is O.K. 3 - LMI on and connection has failed |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.4 | ColumnrcvAbitState | read-only | mandatory | The A bit receive state 1 - LMI off 2 - LMI on and connection is O.K. 3 - LMI on and connection has failed |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.5 | ColumnxmtATMState | read-only | mandatory | This variable indicates the transmit state of the VC (channel) on the ATM side 1 - Not sending any state 2 - Sending AIS OAM state 3 - Sending FERF OAM state |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.6 | ColumnrcvATMState | read-only | mandatory | This variable indicates the receiving state of the VC (channel) on the ATM side 1 - Not receiving any state 2 - Receiving AIS OAM 3 - Receiving FERF OAM |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.7 | ColumnchanStatusBitMap | read-only | mandatory | This variable indicates the consolidated bit map of the channel alarm state. Individual bit positions are as defined below. Bit position Fail/Alarm Reason 0 Al… |
| 1.3.6.1.4.1.351.110.5.1.2.3 | NodefrChanCntGrp | |||
| 1.3.6.1.4.1.351.110.5.1.2.3.1 | TablefrChanCntGrpTable | not-accessible | mandatory | The config table is for logical channel interface there are upto 4000 entries. |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1 | RowfrChanCntGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.1 | ColumncntChanNum | read-only | mandatory | Refers to the virtual connection index Note that the actual range of the index supported by a card depends on the type of card. eg: FRSM-4T1/E1 supports a rang… |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.2 | ColumnrcvFrames | read-only | mandatory | The number of frames Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.3 | ColumnrcvBytes | read-only | mandatory | The number of bytes Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.4 | ColumnrcvFramesDE | read-only | mandatory | The number of DE frames Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.5 | ColumnrcvBytesDE | read-only | mandatory | The number of DE bytes Received on the ingress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.6 | ColumnrcvFramesDiscard | read-only | mandatory | The number of frames discarded on the ingress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.7 | ColumnrcvBytesDiscard | read-only | mandatory | The number of bytes discarded on the ingress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.8 | ColumnrcvFramesDiscShelfAlarm | read-only | mandatory | The number of frames discarded on the ingress due to shelf alarm For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.9 | ColumnrcvFramesDiscXceedQDepth | read-only | mandatory | The number of frames discarded on the ingress due to exceeded queue depth |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.10 | ColumnrcvBytesDiscXceedQDepth | read-only | mandatory | The number of bytes discarded on the ingress due to exceeded queue depth |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.11 | ColumnrcvFramesDiscXceedDEThresh | read-only | mandatory | The number of frames discarded on the ingress due to exceeded DE Threshold |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.12 | ColumnrcvFramesFECN | read-only | mandatory | The number of frames received with FECN bit already set |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.13 | ColumnrcvFramesBECN | read-only | mandatory | The number of frames received with BECN bit already set |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.14 | ColumnrcvFramesTaggedFECN | read-only | mandatory | The number of frames received that were tagged with FECN bit |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.15 | ColumnrcvFramesTaggedBECN | read-only | mandatory | The number of frames received that were tagged with BECN bit |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.16 | ColumnrcvFramesTaggedDE | read-only | mandatory | The number of frames received that were tagged with DE bit |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.17 | ColumnrcvBytesTaggedDE | read-only | mandatory | The number of bytes received that were tagged with DE bit |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.18 | ColumnrcvKbpsAIR | read-only | mandatory | Received Average Information Rate in KBPS |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.19 | ColumnxmtFrames | read-only | mandatory | The number of frames transmitted |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.20 | ColumnxmtBytes | read-only | mandatory | The number of bytes transmitted |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.21 | ColumnxmtFramesFECN | read-only | mandatory | The number of frames transmitted with FECN bit already set |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.22 | ColumnxmtFramesBECN | read-only | mandatory | The number of frames transmitted with BECN bit already set |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.23 | ColumnxmtFramesDE | read-only | mandatory | The number of DE frames transmitted |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.24 | ColumnxmtBytesDE | read-only | mandatory | The number of DE bytes transmitted |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.25 | ColumnxmtFramesDiscard | read-only | mandatory | The number of frames discarded on the eggress |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.26 | ColumnxmtBytesDiscard | read-only | mandatory | The number of bytes discarded on the egress For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.27 | ColumnxmtFramesDiscXceedQDepth | read-only | mandatory | The number of frames discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.28 | ColumnxmtBytesDiscXceedQDepth | read-only | mandatory | The number of bytes discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.29 | ColumnxmtFramesDiscXceedDEThresh | read-only | mandatory | The number of frames discarded on the egress due to exceeded DE Threshold For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.30 | ColumnxmtFramesDiscPhyLayerFail | read-only | mandatory | The number of frames discarded on the egress due to physical layer failure |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.31 | ColumnxmtFramesDiscCRCError | read-only | mandatory | The number of frames discarded on the egress due to CRC Error |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.32 | ColumnxmtFramesDiscReassmFail | read-only | mandatory | The number of frames discarded on the egress due to reassembly failure For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.33 | ColumnxmtFramesDiscSrcAbort | read-only | mandatory | The number of frames discarded on the egress due to source abort |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.34 | ColumnxmtFramesDuringLMIAlarm | read-only | mandatory | The number of frames transmitted during LMI logical port alarm |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.35 | ColumnxmtBytesDuringLMIAlarm | read-only | mandatory | The number of bytes transmitted during LMI logical port alarm |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.36 | ColumnxmtFramesTaggedFECN | read-only | mandatory | The number of frames transmitted that were tagged with FECN bit |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.37 | ColumnxmtFramesTaggedBECN | read-only | mandatory | The number of frames transmitted that were tagged with BECN bit |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.38 | ColumnxmtKbpsAIR | read-only | mandatory | Transmitted Average Information Rate in KBPS |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.39 | ColumnchanClrButton | read-write | mandatory | Channel clear button. Clears Channel Counters. |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.40 | ColumnxmtFramesTaggedDE | read-only | mandatory | The number of frames transmitted which have been DE tagged at the far end ingress in excess of CIR |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.41 | ColumnxmtBytesTaggedDE | read-only | mandatory | The number of bytes transmitted which have been DE tagged at the far end ingress in excess of CIR |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.42 | ColumnrcvFramesDiscUPC | read-only | mandatory | The number of frames discarded at ingress due to the UPC measurement in excess of CIR+EIR |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.43 | ColumnchanSecUpTime | read-only | mandatory | The time in seconds the PVC stay in service |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.44 | ColumnxmtFramesInvalidCPIs | read-only | mandatory | Number of frames transmitted with invalid CPI header. currently valid is 0 |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.45 | ColumnxmtFramesLengthViolations | read-only | mandatory | The number of frames discarded due to violation of length in the egress direction. |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.46 | ColumnxmtFramesOversizedSDUs | read-only | mandatory | The number of frames discarded because the size is beyond the max in the egress direction |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.47 | ColumnxmtFramesUnknownProtocols | read-only | mandatory | The number of frames discarded for Unknown protocol in the egress direction. Used only in SIW for PDUs that are dropped. |
| 1.3.6.1.4.1.351.110.5.1.2.3.1.1.48 | ColumnrcvFramesUnknownProtocols | read-only | mandatory | Number of frames discarded for Unknown protocol in the ingress direction. Used only in SIW for PDUs that are dropped |
| 1.3.6.1.4.1.351.110.5.1.3 | NodefrEndPtMapGrp | |||
| 1.3.6.1.4.1.351.110.5.1.3.1 | TablefrEndPtMapGrpTable | not-accessible | mandatory | Table of transmit/receive states of channels. |
| 1.3.6.1.4.1.351.110.5.1.3.1.1 | RowfrEndPtMapGrpEntry | not-accessible | mandatory | An entry for FrEndPtMapGrpEntry. |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.1 | ColumnendPortNum | read-only | mandatory | Refers to the logical port index For FRSM12 card: The ifIndex of the port's corresponding row in ifTable. Byte 3 = Chassis Number, Byte 2 = Slot Number, Byte 1… |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.2 | ColumnendDLCI | read-only | mandatory | Refers to the DLCI index |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.3 | ColumnendChanNum | read-only | mandatory | Logical connection number 0 if port.dlci is a multicast group Note that the actual range of endChanNum supported by a card depends on the type of card. eg: FRS… |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.4 | ColumnendLineNum | read-only | mandatory | Refers to the physical line index. Note that the actual range of endLineNum supported by a card depends on the type of card. eg: FRSM-4T1/E1 supports a range f… |
| 1.3.6.1.4.1.351.110.5.2.1.1.1 | NodeausmPortCnfPortGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1 | TableausmPortCnfPortGrpTable | not-accessible | mandatory | The config table is for logical port interface there are 8 entries for either T1 or E1 |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1 | RowausmPortCnfPortGrpEntry | not-accessible | mandatory | An entry for logical port. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1.1 | ColumnausmPortNum | read-only | mandatory | This is logical port number. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1.2 | ColumnportEnable | read-write | mandatory | This variable enables or disables the port 1 - disable 2 - enable |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1.3 | ColumnausmPortType | read-write | mandatory | This variable indicates whether UNI/NNI/STI interface STI mode is supported only in IMATM. vpTrkUni should be used only in IMATM when virtual trunks are passin… |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1.4 | ColumnausmPortIfType | read-only | mandatory | This variable indicates the type of interface |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1.5 | ColumnausmPortSpeed | read-only | mandatory | The speed of the port in cells per second |
| 1.3.6.1.4.1.351.110.5.2.1.1.1.1.1.6 | ColumnausmLineNum | read-write | mandatory | The line number associated with the logical port. For AUSM (4 port), the line number is same as the logical port. In AUSM-8p, these two can be different |
| 1.3.6.1.4.1.351.110.5.2.1.1.2 | NodeausmPortCnfServiceQueGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1 | TableausmPortCnfServiceQueGrpTable | not-accessible | mandatory | In AUSM (4port): the Service queue table has 64 entries, 16 each for every port, in addition there are 4 queues for OAM/ILMI traffic In AUSM (8-port), the Serv… |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1 | RowausmPortCnfServiceQueGrpEntry | not-accessible | mandatory | An entry for a single queue |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.1 | ColumnegrQIndex | read-only | mandatory | Egress queue number. In AUSM (4 port), only range from 1..12 is permissible |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.2 | ColumnservicePortNum | read-only | mandatory | Logical port number to which egress queue is associated. In AUSM (4-port card), a logical port is same as a physical port. This is read only and queue mapping … |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.3 | ColumnegrQBinState | read-write | mandatory | Egress queue state |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.4 | ColumnegrQServiceSequence | read-write | mandatory | Egress queue number sequence in the priority list. In AUSM (4 port), range from only 1..12 is permissible |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.5 | ColumnegrQDepthMax | read-write | mandatory | The maximum depth of the egress queue. In AUSM (4 port), range from only 1..8000 is permissible |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.6 | ColumnegrQCLPThreshHigh | read-write | mandatory | High CLP threshold of the egress queue. In AUSM (4 port), range from only 1..8000 is permissible.This value should be less than or equal to egrQDepthMax. |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.7 | ColumnegrQCLPThreshLow | read-write | mandatory | Low CLP threshold of the egress queue. In AUSM (4 port), range from only 1..8000 is permissible. This value should be less than or equal to egrQCLPThreshHigh. |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.8 | ColumnegrQEfciThresh | read-write | mandatory | Threshold of the egress queue for EFCI. In AUSM (4 port), range from only 1..8000 is permissible.This value should be less than or equal to egrQDepthMax. |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.9 | ColumnegrQAlgorithm | read-write | mandatory | The algorithm number for the Egress queue 1-5 are valid values 'ff'h is disable |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.10 | ColumnegrMaxBwInc | read-write | mandatory | The increment for the Maximum carry for the queue. In AUSM (8 port), range from only 1..511 is permissible |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.11 | ColumnegrMinBwInc | read-write | mandatory | The increment for the minimum carry for the queue. In AUSM (8 port), range from only 1..511 is permissible |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.12 | ColumnegrQCLPState | read-only | mandatory | this variable indicates the CLP state for the queue |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.13 | ColumnegrQfullDiscardCells | read-only | mandatory | The number of cells discarded due to Egress Q full |
| 1.3.6.1.4.1.351.110.5.2.1.1.2.1.1.14 | ColumnegrQClpSetDiscardCells | read-only | mandatory | The number of CLP set cells discarded in Egress direction |
| 1.3.6.1.4.1.351.110.5.2.1.1.3 | NodeausmPortCnfSig | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1 | NodeausmPortCnfSigILMIGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1 | TableausmPortCnfSigILMIGrpTable | not-accessible | mandatory | The config table is for upto 8 logical port interfaces |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1 | RowausmPortCnfSigILMIGrpEntry | not-accessible | mandatory | An entry for a logical port. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.1 | ColumnsigPortNum | read-only | mandatory | Refers to the logical port index. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.2 | ColumnausmSignallingProtocolType | read-write | mandatory | This will set the signalling protocol 1 - other 2 - noSignalling 3 - ILMI |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.3 | ColumnsignallingVpi | read-write | mandatory | indicates the VPI on which signalling cells arrive |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.4 | ColumnsignallingVci | read-write | mandatory | indicates the VCI on which signalling cells arrive |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.5 | ColumnaddrPrefix | read-write | mandatory | Network Prefix for the ATM address |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.6 | ColumncustomerId | read-write | mandatory | for the INS as a read/write variable |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.7 | ColumnprotocolRevNo | read-write | mandatory | for the INS as a read/write variable |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.8 | ColumniLMITrapEnable | read-write | mandatory | Enable/disable ILMI Trap sending |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.9 | ColumnminTrapInterval | read-write | mandatory | number of seconds between traps |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.10 | ColumnkeepAlivePollingEnable | read-write | mandatory | Enable/disable Keep Alive Polling |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.11 | ColumnerrorThresholdN491 | read-write | mandatory | Error Threshold (N491) value |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.12 | ColumneventThresholdN492 | read-write | mandatory | Event Threshold (N492) value |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.13 | ColumnpollingIntervalT491 | read-write | mandatory | Polling Interval (T491) value |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.14 | ColumnminEnquiryIntervalT493 | read-write | mandatory | Minimum Enquiry Interval (T493) |
| 1.3.6.1.4.1.351.110.5.2.1.1.3.1.1.1.15 | ColumnaddrRegEnable | read-write | mandatory | Enable/disable ILMI Address Registration |
| 1.3.6.1.4.1.351.110.5.2.1.1.4 | NodeausmPortCnfPortImaGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1 | TableausmPortCnfPortImaGrpTable | not-accessible | mandatory | The config table is for the IMA port (IMA group). There are 8 entries in all. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1 | RowausmPortCnfPortImaGrpEntry | not-accessible | mandatory | An entry for every IMA port (total of 8 entries) |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.1 | ColumnimaPortNum | read-only | mandatory | This is the logical port number. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.2 | ColumnimaPortEnable | read-write | mandatory | This variable enables, disables or modifies the configuration of the port 1 - delport (Disables the entire IMA group) 2 - addport (Enables the IMA group) 3 - a… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.3 | ColumnimaPortSpeed | read-only | mandatory | The speed of the port in cells per second. This depends on the nuber of links in the IMA group and the configuration of the physical interface on each link (eg… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.4 | ColumnnumLinksInImaGrp | read-only | mandatory | The number of links configured in the IMA group This is same as axisImaGroupNumTxCfgLnks in Forum Compliant Ima |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.5 | ColumnlistOfLinksInImaGrp | read-write | mandatory | The list of links in the IMA group delimited by dots |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.6 | ColumnlcpCellsPeriodicity | read-only | mandatory | Period at wich LCP cells of the IMA protocol can be transmitted. A value of 32 indicates that after 32 cells, one LCP cell is transmitted on that link of the I… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.7 | ColumnlcpDelayTolerance | read-only | mandatory | The number of IMA frames for which an LCP cell on any link can be missed before the IMA state machine should remove the link from the IMA group. At present, th… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.8 | ColumnreadPtrWrPtrDiff | read-write | mandatory | The difference between the read and write pointer of a link in the common cell buffer. A lower value reduces the latency in the common cell buffer but also inc… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.9 | ColumnnumRedundantLinks | read-write | mandatory | The degree of resiliency in the IMA group. This indicates the number of links the system can lose from this IMA group without bringing it down. By default, the… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.10 | ColumnmaxTolerableDiffDelay | read-write | mandatory | This indicates the maximum tolerable differential delay in milliseconds between the various links in the IMA group. The default value is variable and depends o… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.11 | ColumnimaPortType | read-write | mandatory | This indicates whether the port is to be configured for UNI/NNI/STI mode. STI mode is supported only in the case of IMATM. vpTrkUni should be used only in IMAT… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.12 | ColumnaxisImaGroupTxAvailCellRate | read-only | mandatory | The current cell rate(truncated value in cells per second) provided by the IMA group in the transmit direction, considering all the transmit links in the Activ… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.13 | ColumnaxisImaGroupSymmetry | read-write | mandatory | Symmetry of the IMA group. AsymmetricOperation,AsymmetricConfiguration are not supported. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.14 | ColumnaxisImaGroupMinNumRxLinks | read-write | mandatory | Minimum number of receive links required to be active for the IMA group to be in the Up state.At present since only symmetric configuration is supported,this s… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.15 | ColumnaxisImaGroupNeTxClkMode | read-write | mandatory | Transmit clocking mode used by the near-end IMA group. ITC is not available in ausm8(B). Only default value (ctc) is supported. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.16 | ColumnaxisImaGroupAlphaValue | read-only | mandatory | This indicates the 'alpha' value used to specify the number of consecutive invalid ICP cells to be detected before moving to the IMA HUNT state. Only default v… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.17 | ColumnaxisImaGroupBetaValue | read-only | mandatory | This indicates the 'beta'value used to specify the number of consecutive errored ICP cells to be detected before moving to the IMA HUNT state. Only default val… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.18 | ColumnaxisImaGroupGammaValue | read-only | mandatory | This indicates the 'gamma' value used to specify the number of consecutive valid ICP cells to be detected before moving to the IMA SYNC state from the PRESYNC … |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.19 | ColumnaxisImaGroupNumRxCfgLnks | read-only | mandatory | The Number of links that are configured to receive in this IMA Group. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.20 | ColumnaxisImaGroupTestLinkIfIndex | read-write | mandatory | This object is used to designate an interface as the test link. A value of -1 specifies that the implementation may choose the test link. In this case ,the imp… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.21 | ColumnaxisImaGroupTestPattern | read-write | mandatory | The value of this object is used to specify the test pattern in an IMA group loopback operation. A value in the range 0 to 255 designates a specific pattern. A… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.22 | ColumnaxisImaGroupTestProcStatus | read-write | mandatory | This object is used to enable or disable the Test Pattern Proceudre,and to note whether at least one link failed the test. The test is started by setting opera… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.23 | ColumnaxisImaGroupIntegrationUpTime | read-write | mandatory | Integration UP time for alarm integration.Persisting checking time to enter a failure alarm condition,in case of LIF,LODS,RFI-IMA fault failure alarms. Time in… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.24 | ColumnaxisImaGroupIntegrationDownTime | read-write | mandatory | Integration DOWN time for alarm integration.Persisting clearing time to exit the LIF,LODS,RFI-IMA failure alarm conditions. Time in Milli seconds. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.25 | ColumnaxisImaGroupMinNumTxLinks | read-write | mandatory | Minimum number of transmit links required to be active for the IMA group to be in the Up state.Eventhough the range is 1..8,this value should be <= maximum num… |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.1.1.26 | ColumnaxisImaGroupRxImaId | read-only | mandatory | The Ima id used by the far end. |
| 1.3.6.1.4.1.351.110.5.2.1.1.4.2 | ScalarnextPortNumAvailable | read-only | mandatory | Indicates the next logical port number (i.e. either ATM T1/E1 UNI or IMA port) that is available |
| 1.3.6.1.4.1.351.110.5.2.1.1.5 | NodeausmPortCnfResPartGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1 | TableausmPortCnfResPartGrpTable | not-accessible | mandatory | The config table is for logical port interface there are 4/8 entries for either T1 or E1 or AIMUX ports For PXM (MGX), there are 32 entries. |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1 | RowausmPortCnfResPartGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.1 | ColumnausmResPartPortNum | read-only | mandatory | This is logical port number In PXM, a port refers to the Logical Broadband Interface. Refer bbIfCnfPortGrp.my for more information. |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.2 | ColumnausmPortSvcInUse | read-write | mandatory | Setting this object to 1 indicates that the resources (LCN/Local VPID/VCI/VPI) have been partitioned and INS and SV+ are currently using this information. The … |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.3 | ColumnausmPortSvcShareLcnVpid | read-only | mandatory | Indicates whether or not the LCN and VPid address spaces are shared across all the ports. Default value is 2 (cardBased). |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.4 | ColumnausmPortSvcLcnLow | read-write | mandatory | The beginning of the LCN range reserved for SVCs. Both the LCN low and high values apply to all ports when the 'atmPortSvcShareLcnVpid' object is set to 2 (Car… |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.5 | ColumnausmPortSvcLcnHigh | read-write | mandatory | The end of the LCN range reserved for SVCs. |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.6 | ColumnausmPortSvcVpidLow | read-write | mandatory | The beginning of the VPID range reserved for SVCs. Both the VPID low and high values apply to all ports when the 'atmPortSvcShareLcnVpid' object is set to 2 (C… |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.7 | ColumnausmPortSvcVpidHigh | read-write | mandatory | The end of the VPID range reserved for SVCs. |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.8 | ColumnausmPortSvcVciLow | read-write | mandatory | The beginning of the VCI range reserved for SVCs. For VPI connections the valid VCI values are 0 - 4095 |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.9 | ColumnausmPortSvcVciHigh | read-write | mandatory | The end of the VCI range reserved for SVCs. For VPI connections the valid VCI values are 0 -4095 |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.10 | ColumnausmPortSvcVpiLow | read-write | mandatory | The beginning of the VCI range reserved for SVCs. |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.11 | ColumnausmPortSvcVpiHigh | read-write | mandatory | The end of the VPI range reserved for SVCs. |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.12 | ColumnausmPortIngrSvcBandW | read-write | mandatory | This represents Ingress Bandwidth reserved for SVC |
| 1.3.6.1.4.1.351.110.5.2.1.1.5.1.1.13 | ColumnausmPortEgrSvcBandW | read-write | mandatory | This represents Egress Bandwidth reserved for SVC |
| 1.3.6.1.4.1.351.110.5.2.1.1.6 | NodeausmPortDelSvcsGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.6.1 | TableausmPortDelSvcsGrpTable | not-accessible | mandatory | The table is for logical port interface there are 4/8 entries for either T1 or E1 or AIMUX ports For PXM (MGX), there are 32 entries. |
| 1.3.6.1.4.1.351.110.5.2.1.1.6.1.1 | RowausmPortDelSvcsGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.2.1.1.6.1.1.1 | ColumnausmDelSvcsPortNum | read-only | mandatory | This is logical port number In PXM, a port refers to the Logical Broadband Interface. Refer bbIfCnfPortGrp.my for more information. |
| 1.3.6.1.4.1.351.110.5.2.1.1.6.1.1.2 | ColumnausmPortDeleteSvcs | read-write | mandatory | Setting this object to 1 indicates that all the SVC connections on the given port has to be deleted |
| 1.3.6.1.4.1.351.110.5.2.1.1.7 | NodeausmPortImaGrpRestart | |||
| 1.3.6.1.4.1.351.110.5.2.1.1.7.1 | TableausmPortImaGrpRestartTable | not-accessible | mandatory | The restart table is for the IMA port (IMA group). There are 8 entries in all. |
| 1.3.6.1.4.1.351.110.5.2.1.1.7.1.1 | RowausmPortImaGrpRestartEntry | not-accessible | mandatory | An entry for every IMA port (total of 8 entries) |
| 1.3.6.1.4.1.351.110.5.2.1.1.7.1.1.1 | ColumnaxisImaGroupimaPortNum | read-only | mandatory | This is the logical port number. |
| 1.3.6.1.4.1.351.110.5.2.1.1.7.1.1.2 | ColumnaxisImaGroupRestartImaGrp | read-write | mandatory | This variable restarts the Ima grp. We have the option of relearning the Ima id or retaining the stored ID. |
| 1.3.6.1.4.1.351.110.5.2.1.2 | NodeausmPortStateGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.2.1 | TableausmPortStateGrpTable | not-accessible | mandatory | The state table for the port interface there are 8 entries for either T1 or E1 or IMA. |
| 1.3.6.1.4.1.351.110.5.2.1.2.1.1 | RowausmPortStateGrpEntry | not-accessible | mandatory | An entry for logical port. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.2.1.1.1 | ColumnausmStatePortNum | read-only | mandatory | This is logical port number. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.2.1.1.2 | ColumnausmPortState | read-only | mandatory | This variable indicates the status of the port |
| 1.3.6.1.4.1.351.110.5.2.1.2.1.1.3 | ColumnausmPortOversubscribed | read-only | mandatory | This variable indicates the whether the port is over subscribed or not |
| 1.3.6.1.4.1.351.110.5.2.1.2.1.1.4 | ColumnausmPortIngrPercentUtil | read-only | mandatory | Percentage Utilization of the Port in the Ingress direction. |
| 1.3.6.1.4.1.351.110.5.2.1.2.1.1.5 | ColumnausmPortEgrPercentUtil | read-only | mandatory | Percentage Utilization of the Port in the Egress direction. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1 | NodeausmPortCntPortGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1 | TableausmPortCntPortGrpTable | not-accessible | mandatory | The config table is for logical port interface there are 8 entries for either T1 or E1 |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1 | RowausmPortCntPortGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.1 | ColumnausmCntPortNum | read-only | mandatory | This is the logical port number. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.2 | ColumningrRcvCells | read-only | mandatory | The number of cells received in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.3 | ColumningrGfcErrCells | read-only | mandatory | The number of cells received in Ingress direction with non zero-GFC |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.4 | ColumningrVpiVciErrCells | read-only | mandatory | The number of cells received in Ingress direction with unknown VpiVci |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.5 | ColumningrLastUnknVpiVci | read-only | mandatory | The last unknown Vpi Vci value |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.6 | ColumnegrXmtCells | read-only | mandatory | The number of cells transmitted in the egress direction |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.7 | ColumnegrPortAlarmDiscardCells | read-only | mandatory | The number of cells discarded due to port alarm |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.8 | ColumnegrXmtClpSetCells | read-only | mandatory | The number of cells transmitted in Egress direction with CLP bit set |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.9 | ColumnegrXmtEfciSetCells | read-only | mandatory | The number of cells transmitted in Egress direction with EFCI bit set |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.10 | ColumnportXmtAisCells | read-only | mandatory | The number of AIS cells transmitted towards port |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.11 | ColumnportXmtSgmtLpbkCells | read-only | mandatory | The number of Segment Loopback cells transmitted towards port |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.12 | ColumnportRcvAisCells | read-only | mandatory | The number of AIS cells received in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.13 | ColumnportRcvFerfCells | read-only | mandatory | The number of FERF cells received in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.14 | ColumnportRcvSgmtLpbkCells | read-only | mandatory | The number of Segment Loopback cells received in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.15 | ColumnportRcvCrcErrOAMCells | read-only | mandatory | The number of OAM cells received in Ingress direction with CRC error |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.16 | ColumnausmPortClrButton | read-write | mandatory | writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.17 | ColumningrRcvClpSetCells | read-only | mandatory | The number of cells received from the port which had the CLP bit in the ATM cell header equal to 1. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.18 | ColumningrXmtCells | read-only | mandatory | The number of cells out of the received cells from the port that were sent to the network. This count is taken after policing and ingress queueing. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.19 | ColumnegrRcvCells | read-only | mandatory | The number of cells received from the network in the egress direction |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.20 | ColumningrRcvCellRate | read-only | mandatory | The number of cells received per second from the port in the ingress direction. Maximum value is 5000 because because clear E1 rate is 4830. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.21 | ColumningrRcvUtilization | read-only | mandatory | The percentage utilization of the port speed in the ingress direction. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.22 | ColumnegrXmtCellRate | read-only | mandatory | The number of cells received transmitted to the port in the egress direction. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.23 | ColumnegrXmtUtilization | read-only | mandatory | The percentage utilization of the port speed in the egress direction. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.24 | ColumnegrRcvCellRate | read-only | mandatory | The number of cells received per second from the network in the egress receive direction. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.25 | ColumnegrRcvUtilization | read-only | mandatory | The percentage utilization of the port speed in the egress receive direction. |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.26 | ColumntotalIngrQfulldiscardCells | read-only | mandatory | The total number of cells dropped on all the channels on this port because the the ingress Q was full. Adds up all the IngressQfull discard per channel statist… |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.27 | ColumntxFifoFullCnt | read-only | mandatory | This statistics provides a count of the number of times the AUSM card tried to send a cell, but was unable to send because the Transmit FIFO was full. Note tha… |
| 1.3.6.1.4.1.351.110.5.2.1.3.1.1.1.28 | ColumntotalIngrClpSetDiscardCells | read-only | mandatory | The total number of cells with CLP=1 dropped on all the channels on this port because of either PCR Exceeded, SCR exceeded (with CLP tagging disabled) or CLP H… |
| 1.3.6.1.4.1.351.110.5.2.1.3.2 | NodeausmPortCntSig | |||
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1 | NodeausmPortCntSigILMIGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1 | TableausmPortCntSigILMIGrpTable | not-accessible | mandatory | The config table is for physical port interface there are 8 entries for either T1 or E1 or IMA |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1 | RowausmPortCntSigILMIGrpEntry | not-accessible | mandatory | An entry for logical port. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.1 | ColumnsigCntPortNum | read-only | mandatory | This is the logical port number. |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.2 | ColumnsnmpPduReceived | read-only | mandatory | The number of snmp packets received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.3 | ColumngetRequestReceived | read-only | mandatory | The number of get request messages received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.4 | ColumngetNextRequestReceived | read-only | mandatory | The number of get-next messages received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.5 | ColumnsetRequestReceived | read-only | mandatory | The number of set messages received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.6 | ColumntrapReceived | read-only | mandatory | The number of traps received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.7 | ColumngetResponseReceived | read-only | mandatory | The number of Keep Alive response messages received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.8 | ColumngetResponseTransmitted | read-only | mandatory | The number of response messages transmitted |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.9 | ColumngetRequestTransmitted | read-only | mandatory | The number of Keep Alive get request messages transmitted |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.10 | ColumntrapTransmitted | read-only | mandatory | The number of trap messages transmitted |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.11 | ColumninvalidPDUReceived | read-only | mandatory | The number of invalid PDUs received |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.12 | Columnasn1ParseError | read-only | mandatory | The number of parse errors on ASN.1 |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.13 | ColumnnoSuchNameError | read-only | mandatory | The number of errors for name not present |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.14 | ColumntooBigError | read-only | mandatory | The number of messages received with len > 484 |
| 1.3.6.1.4.1.351.110.5.2.1.3.2.1.1.1.15 | ColumnportSigClrButton | read-write | mandatory | writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.1.3.3 | NodeausmPortCntPortImaGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1 | TableausmPortCntPortImaGrpTable | not-accessible | mandatory | The counter table is for the IMA groups (8 possible entries) |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1 | RowausmPortCntPortImaGrpEntry | not-accessible | mandatory | An entry for the IMA group |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.1 | ColumnimaCntPortNum | read-only | mandatory | This is the logical port number. This object does not have any default value. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.2 | ColumnrcvAcpCells | read-only | mandatory | This is the number of ICP cells received. This object does not have any default value. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.3 | ColumnrcvAcpErrCells | read-only | mandatory | This is the number of errored ICP cells on this IMA group. This object does not have any default value. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.4 | ColumnxmtAcpCells | read-only | mandatory | This is the number of ACP cells transmitted on this IMA group. This object does not have any default value. Not supported in Forum Compliant Ima. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.5 | ColumnxmtAcpCellsMissed | read-only | mandatory | This is the number of ACP cells that could not be transmitted on this IMA group due to lack of resources (buffers). This object does not have any default value… |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.6 | ColumnimaGrpRcvHecErrCount | read-only | mandatory | This is the number of HEC errored cells received on all the links currently in the IMA group This object does not have any default value. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.7 | ColumnimaGrpRcvHecErrSecCount | read-only | mandatory | This is the number of HEC errored seconds for the IMA group that is the number of seconds in which at least one link in the IMA group experienced a HEC error T… |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.8 | ColumnimaGrpRcvHecErrSESecCount | read-only | mandatory | This is the number of severely errored seconds received on all the links currently in the IMA group. A severely errored second for an IMA group is defined if t… |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.9 | ColumnimaCntClrButton | read-write | mandatory | writing a value of 2 resets all the counters This object does not have any default value. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.10 | ColumnaxisImaGroupRunningSecs | read-only | mandatory | The amount of time(in seconds) since this IMA group has been in opeartion(UP or DOWN.) |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.11 | ColumnaxisImaGroupUnavailSecs | read-only | mandatory | Count of one second intervals where IMA group traffic state machine is down. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.12 | ColumnaxisImaGroupNeNumFailures | read-only | mandatory | The number of times a near-end group failure(Config-abort, Insufficient-Links) has been reported since power-up or reboot. |
| 1.3.6.1.4.1.351.110.5.2.1.3.3.1.1.13 | ColumnaxisImaGroupFeNumFailures | read-only | mandatory | The number of times a far-end group failure(config-abort-FE, Insufficient-links-FE,Blocked-FE) has been reported since power-up or reboot. |
| 1.3.6.1.4.1.351.110.5.2.1.4 | NodeausmPortStateImaGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.4.1 | TableausmPortStateImaGrpTable | not-accessible | mandatory | The state table for the IMA port interface: there are 8 entries for the 8 (maximum possible) IMA groups |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1 | RowausmPortStateImaGrpEntry | not-accessible | mandatory | An entry for every IMA group |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.1 | ColumnimaStatePortNum | read-only | mandatory | This is the logical port number This object does not have any default value |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.2 | ColumnimaPortState | read-only | mandatory | Indicates the state of the IMA port. The following error conditions are currently reported: 1 - Unconfigured state 2 - Active state 3 - Bandwidth changed due t… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.3 | ColumnnumLinksPresentInImaGroup | read-only | mandatory | Indicates the number of links that are currently present in the IMA group. This object does not have any default value Same as axisImaGroupNumTxActLnks in Foru… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.4 | ColumnlistLinksPresentInImaGroup | read-only | mandatory | Indicates the list of links currently present in the IMA group. Different links in the IMA group are delimited by dots. The position of each link in the displa… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.5 | ColumnremoteImaId | read-only | mandatory | Indicates the IMA-ID in use at the remote end when sending LCP/ACP cells. Same as axisImaGroupRxImaId in Forum Compliant Ima . This object does not have any de… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.6 | ColumnlocImaId | read-only | mandatory | Indicates the IMA-ID in use at the local end when sending LCP/ACP cells. This is same as axisImaGroupTxImaId in Forum Compliant Ima This object does not have a… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.7 | ColumnimaArbitrationWinner | read-only | mandatory | Result of arbitration between the two ends of the IMA pipe. This object does not have any default value Retaining for the backward compatibility. Not supported… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.8 | ColumnimaObsDiffDelay | read-only | mandatory | The observed differential delay in milliseconds between the different physical links in the IMA group This object does not have any default value Same as axisI… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.9 | ColumnimaPortOversubscribed | read-only | mandatory | This variable indicates whether the port is over-subscribed or not This object does not have any default value |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.10 | ColumnimaPortIngrPercentUtil | read-only | mandatory | Percent Utilization of the IMA Port in the Ingress direction This object does not have any default value |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.11 | ColumnimaPortEgrPercentUtil | read-only | mandatory | Percent Utilization of the IMA Port in the Egress direction This object does not have any default value |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.12 | ColumnaxisImaGroupRxAvailCellRate | read-only | mandatory | The current cell-rate (truncated value in cells per second) provided by this IMA group in the receive direction,considering all the receive links in the active… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.13 | ColumnaxisImaGroupFeState | read-only | mandatory | The current operational state of the far-end IMA group state machine 1) notConfigured : The Group doesn't exist.This is the GSM initial state. 2) startUp : On … |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.14 | ColumnaxisImaGroupFailureStatus | read-only | mandatory | The current failure status of the IMA group(the reason why the GTSM is in the DOWN state. 1) noFailure : The group is UP. 2) startUpNe : When the NE GSM is in … |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.15 | ColumnaxisImaGroupFeTxClkMode | read-only | mandatory | Transmit clocking mode used by the far-end IMA group. |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.16 | ColumnaxisImaGroupTxTimingRefLink | read-only | mandatory | The IfIndex of the transmit timing reference link to be used by the near-end for IMA data cell clock recovery from the ATM layer. |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.17 | ColumnaxisImaGroupRxTimingRefLink | read-only | mandatory | The IfIndex of the receive timing reference link to be used by the near-end for IMA data cell clock recovery toward the ATM layer. |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.18 | ColumnaxisImaGroupLastChange | read-only | mandatory | The time-of-day the IMA group last changed operational state( i.e. value of axisImaGroupNeState changed.) SPLAY-HINT 2d-1d-1d,1d:1d:1d.1d,1a1d:1d field octets … |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.19 | ColumnaxisImaGroupRxFrameLength | read-only | mandatory | Value of IMA frame length as received from remote IMA function. |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.20 | ColumnaxisImaGroupLeastDelayLink | read-only | mandatory | The IfIndex of the link configured in the IMA group which has the smallest link propagation delay. This value has meaning only if at least 1 link has been conf… |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.21 | ColumnaxisImaGroupNumRxActLnks | read-only | mandatory | The number of links which are configured to receive and are currently Active in this IMA group. |
| 1.3.6.1.4.1.351.110.5.2.1.4.1.1.22 | ColumnaxisImaGroupNeState | read-only | mandatory | The current operational state of the near-end IMA group state machine. 1) notConfigured : The Group doesn't exist.This is the GSM initial state. 2) startUp : O… |
| 1.3.6.1.4.1.351.110.5.2.1.4.2 | ScalaraxisImaGroupNumber | read-only | mandatory | The number of IMA groups configured with the lines. |
| 1.3.6.1.4.1.351.110.5.2.1.5 | NodeausmPortInterfaceGrp | |||
| 1.3.6.1.4.1.351.110.5.2.1.5.1 | TableausmInterfaceConfTable | not-accessible | mandatory | This table contains ATM local interface configuration parameters, one entry per ATM (ausm) interface port. |
| 1.3.6.1.4.1.351.110.5.2.1.5.1.1 | RowausmInterfaceConfEntry | not-accessible | mandatory | This list contains ATM interface configuration parameters and state variables and is indexed by ausmInterfacePortNum values of ATM interfaces. |
| 1.3.6.1.4.1.351.110.5.2.1.5.1.1.1 | ColumnausmInterfacePortNum | read-only | mandatory | This is logical port number. In AUSM, a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.1.5.1.1.2 | ColumnausmInterfaceMyNeighborIpAddress | read-only | mandatory | The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams… |
| 1.3.6.1.4.1.351.110.5.2.2.1 | NodeausmChanCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.2.2.1.1 | TableausmChanCnfGrpTable | not-accessible | mandatory | The config table is for logical channel interface there are 1000 entries for the 8 logical ports in AUSM (8-port) and 256 entries for the 4 logical ports in AU… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1 | RowausmChanCnfGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.1 | ColumnausmChanNum | read-only | mandatory | Refers to the virtual connection index. In AUSM (4-port card), valid range is from 16..271. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.2 | ColumnausmChanRowStatus | read-write | mandatory | This will add, delete or modify the channel 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY Setting this object to outOfService takes the channel out of service or brings … |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.3 | ColumnchanConnType | read-write | mandatory | This specifies the connection type 1 ==> Virtual Path Connection 2 ==> Virtual Channel Connection |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.4 | ColumnchanServiceType | read-write | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Available Bit Rate 4 ==> Unspecified Bit Rate 5 ==> Real-Time Variable Bi… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.5 | ColumnchanConnDesc | read-write | mandatory | A string that has been defined to give a descriptive name to the connection |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.6 | ColumnchanSvcFlag | read-write | mandatory | This specifies the connection type 1 ==> SVC connection 2 ==> PVC connection 3 ==> SPVC connection 4 ==> connection added by PAR 5 ==> connection added by PNNI… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.7 | ColumnchanSvcConnId | read-write | mandatory | This connection ID is for future use Currently not supported |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.8 | ColumnausmChanPortNum | read-write | mandatory | Refers to the logical port on the board to which logical channel is associated. In AUSM (4-port card), a logical port is same as a physical port. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.9 | ColumnchanVpi | read-write | mandatory | The VPI value for this channel |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.10 | ColumnchanVci | read-write | mandatory | The VCI value for this channel |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.11 | ColumnchanEgrQSelect | read-write | mandatory | Selects one out of the 16 possible queues Each queue may have a different service algorithm |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.12 | ColumningrQDepth | read-write | mandatory | This variable sets the max depth for queue, before it starts dropping the cells. In AUSM (4-port card), the valid range is from 1..8000. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.13 | ColumningrQCLPThreshHigh | read-write | mandatory | This variable sets the higher threshold for dropping CLP set cells in the ingress direction. In AUSM (4-port card), the valid range is from 1..8000.This value … |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.14 | ColumningrQCLPThreshLow | read-write | mandatory | This variable sets the lower threshold for dropping CLP set cells in the ingress direction. In AUSM (4-port card), the valid range is from 1..8000.This value s… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.15 | ColumningrQCLPState | read-only | mandatory | This variable indicates the CLP state for the channel |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.16 | ColumningrQEfciThresh | read-write | mandatory | This variable sets the efci threshold value for setting efci bit in the ingress direction. In AUSM (4-port card), the valid range is from 1..8000.This value sh… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.17 | ColumningrUpcEnable | read-write | mandatory | enables/disables UPC for Ingress cells |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.18 | ColumningrUpcPCR01 | read-write | mandatory | Peak Cell Rate for CLP [0+1] cells. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA E1 (norm… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.19 | ColumningrUpcCIR | read-write | mandatory | Complaint Information Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA E1 (normal) or I… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.20 | ColumningrUpcCCDV | read-write | mandatory | Complaint Cell Delay Variation for all cells |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.21 | ColumningrUpcCBS | read-write | mandatory | Complaint Burst Size The unit of this parameter is in terms of number of cells. CBS is applicable only for VBR and ABR connections. In MGX switches, release 3.… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.22 | ColumningrUpcIBS | read-write | mandatory | Initial Burst Size. The Burst size allowed for a connection that has been idle for some time. The unit of this parameter is in terms of number of cells. IBS is… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.23 | ColumningrUpcMFS | read-write | mandatory | Maximum Frame Size |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.24 | ColumningrUpcSCRPolicing | read-write | mandatory | selects SCR policing for CLP = 0 or all cells |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.25 | ColumningrUpcPCR0 | read-write | mandatory | Peak Cell Rate for CLP=0 cells. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA E1 (normal) … |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.26 | ColumningrUpcCDVT0 | read-write | mandatory | Complaint Cell Delay Variation for CLP=0 cells |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.27 | ColumningrUpcCLPTagEnable | read-write | mandatory | enables/disables CLP tagging for Ingress cells |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.28 | ColumningrUpcFGCRAEnable | read-write | mandatory | enables/disables Frame based GCRA |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.29 | ColumnforesightEnable | read-write | mandatory | enables/disables Foresight |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.30 | ColumnforesightMIR | read-write | mandatory | Minimum Information Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA E1 (normal) or IMA… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.31 | ColumnforesightPIR | read-write | mandatory | Peak Information Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA E1 (normal) or IMA E1… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.32 | ColumnforesightQIR | read-write | mandatory | Quiescent Information Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA E1 (normal) or I… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.33 | ColumnausmChanLocRmtLpbkState | read-write | mandatory | The default is disable. This variable enables or disables the remote loopback for each channel. When you enable this option on a connection (channel) then all … |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.34 | ColumnausmChanTestType | read-write | mandatory | The default is notest. The chanTestType starts testing the continuity or delay of a connection. It sends specific cell patterns toward the network and the term… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.35 | ColumnausmChanTestState | read-only | mandatory | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.36 | ColumnausmChanRTDResult | read-only | mandatory | This is round trip delay in milliseconds. When you select testdelay option for the chanTestType, the result of the test that is measured in milliseconds can be… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.37 | ColumnausmChanTestTypeCPESide | read-write | mandatory | The default is notest. The chanTestType starts testing the segment continuity of a connection. It sends OAM Segment loopback cell towards port side (CPE) The C… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.38 | ColumnausmChanTestStateCPESide | read-only | mandatory | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.39 | ColumnausmChanIngrPercentUtil | read-write | mandatory | Percentage Utilization of the IngrService Rate. This is used for connection admission control. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.40 | ColumnausmChanEgrPercentUtil | read-write | mandatory | Percentage Utilization of the EgrService Rate. This is used for egress bandwidth calculation and connection admission control. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.41 | ColumnausmChanEgrSrvRate | read-write | mandatory | Egress service rate - This is used for egress bandwidth calculation and for connection admission control. The actual value depends on the speed of the logical … |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.42 | ColumnausmChanOvrSubOvrRide | read-write | mandatory | This MIB variable allows one to add a new connection on a port even if it is over subscribed. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.43 | ColumnausmChanLocalVpId | read-write | mandatory | Every VP connection will have a unique local VpId between 1 to 340. This is sent to ASC at the time of vp connection setup. This number along with the slot num… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.44 | ColumnausmChanRMEnable | read-write | mandatory | enables/disables sending Resource Mangement Cells |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.45 | ColumnausmIngrDiscardOption | read-write | mandatory | This variable specifies whether Frame based Discard is to be enabled or CLP Threshold is to be used for determining the criterion for dropping cells. FrameDisc… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.46 | ColumnausmIngrFrDiscardThreshold | read-write | mandatory | This variable specifies the Ingress Frame Discard Threshold. Valid only when Ingress Frame Discard option is selected. By default, the value of this variable w… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.47 | ColumnausmCDRNumber | read-write | mandatory | This is the key to correlate cell/frame counts, start/end record. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.48 | ColumnausmLocalVpi | read-only | mandatory | This VPI has different meaning with the end point VPI (CPE), it can be same with the end point VPI but not necessary, it represents the local end point VPI, th… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.49 | ColumnausmLocalVci | read-only | mandatory | This VCI has different meaning with the end point VCI (CPE), it can be same with the end point VPI but not necessary it represents the local end point VCI, thi… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.50 | ColumnausmLocalNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 2 bytes rsvd, 2 bytes for slot (5 bits) and port number (11 bits)… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.51 | ColumnausmRemoteVpi | read-write | mandatory | This VPI has different with the remote end point VPI (CPE), this is similar to a connection ID and it can be same with the remote end point VPI but not necessa… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.52 | ColumnausmRemoteVci | read-write | mandatory | This VCI has different with the remote end point VCI (CPE), this is similar to a connection ID and it can be same with the remote end point VPI but not necessa… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.53 | ColumnausmRemoteNSAP | read-write | mandatory | This NSAP is 20bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 2 bytes rsvd, 2 bytes for slot (5 bits) and port number (11 bits),… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.54 | ColumnausmMastership | read-write | mandatory | This is used by PXM to determine if this end point is master or slave. In AXIS shelf, unknown is always used, but in MGX shelf, if unknown is set, PXM will fai… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.55 | ColumnausmVpcFlag | read-write | mandatory | This represents the connection type, used for PXM to identify VPC/VCC |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.56 | ColumnausmConnServiceType | read-write | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard … |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.57 | ColumnausmRoutingPriority | read-write | mandatory | This is also known as class of service, it is used by PXM to determine how important this connection is when selecting connections to route |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.58 | ColumnausmMaxCost | read-write | mandatory | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. W… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.59 | ColumnausmRestrictTrunkType | read-write | mandatory | Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.60 | ColumnausmConnPCR | read-write | mandatory | Peak cell rate, if not set in MGX, will be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.61 | ColumnausmConnMCR | read-write | mandatory | Minimum cell rate, if not set in MGX, will be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.62 | ColumnausmConnPercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by theis end-point. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.63 | ColumnausmConnRemotePCR | read-write | mandatory | Peak cell rate of the other end, if not set in MGX, will be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.64 | ColumnausmConnRemoteMCR | read-write | mandatory | Minimum cell rate of the other end, if not set in MGX, will be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.65 | ColumnausmConnRemotePercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by the other end-point. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.66 | ColumnausmConnForeSightEnable | read-write | mandatory | This object is used by the controller(PAR/PNNI/TAG) to set up the Qbin for the connection |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.67 | ColumnausmConnFGCRAEnable | read-write | mandatory | enables/disables Frame based GCRA (early packet discard). |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.68 | ColumnausmChanReroute | read-write | mandatory | This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to fals… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.69 | ColumnausmConnSCR | read-write | mandatory | Sustained cell rate, Used for VBR connections setup with PNNI controller. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.70 | ColumnausmConnRemoteSCR | read-write | mandatory | Sustained cell rate of the other end, Used for VBR connections setup with PNNI controller. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.71 | ColumnausmConnMBS | read-write | mandatory | Maximum burst size, Used for VBR connections setup with PNNI controller. In MGX switches, release 3.0.0.0 and above, the default value is 1024 |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.72 | ColumnausmConnRemoteMBS | read-write | mandatory | Maximum burst size at the remote end of the connection, Used for VBR connections setup with PNNI controller. |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.73 | ColumnausmConnTemplateId | read-write | mandatory | This object specifies the template identifier for the connection template associated with this connection. The valid range for templates is 1..16. A value of 1… |
| 1.3.6.1.4.1.351.110.5.2.2.1.1.1.74 | ColumnausmConnAdminStatus | read-write | mandatory | This object specifies channel admin status. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.2.2.1.2 | ScalarausmChanNumNextAvailable | read-only | mandatory | This variable contains the next unused channel number of the possible 1000. This number can be used in channel config table. ChanNumNextAvailable gets updated … |
| 1.3.6.1.4.1.351.110.5.2.2.1.3 | ScalarausmChanVpIdNextAvailable | read-only | mandatory | This variable contains the next unused local VPId of the possible 1 to 100. This number can be used in channel config table. It gets updated if the number is u… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4 | TableausmStdABRCnfGrpTable | not-accessible | mandatory | The ABR config table is for logical channel interface there are 1000 entries for the 8 logical ports in AUSM (8-port). |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1 | RowausmStdABRCnfGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.1 | ColumnausmStdABRCnfChanNum | read-only | mandatory | Refers to the virtual connection index. |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.2 | ColumnausmStdABRType | read-write | mandatory | StdabrType of value 1 indicates a TM4.0 switch behaving connection (Transparent connection) which assumes that RM cells will be received from a TM4.0 compliant… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.3 | ColumnausmStdABRTBE | read-write | mandatory | Transient Buffer Exposure. The unit is number of cells. |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.4 | ColumnausmStdABRFRTT | read-write | mandatory | Fixed Round-Trip Time. The unit is milliseconds. Value 0 signifies that FRTT value is not available. |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.5 | ColumnausmStdABRRDF | read-write | mandatory | Rate Decrease Factor. This unitless value has to be inversed to arrive at the actual value. The valid values possible are only powers of 2; i.e. 1, 2, 4, 8 ...… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.6 | ColumnausmStdABRRIF | read-write | mandatory | Rate Increase Factor. This unitless value has to be inversed to arrive at the actual value. The valid values possible are are only powers of 2; i.e. 1, 2, 4, 8… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.7 | ColumnausmStdABRNrm | read-write | mandatory | Maximum number of cells a source may send for each forward RM cell. The valid values possible are only powers of 2 starting from 2 ; i.e. 2, 4, 8 ..... 256. Th… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.8 | ColumnausmStdABRTrm | read-write | mandatory | Upper bound on the time between forward RM cells for an active source. The unit is in milliseconds. |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.9 | ColumnausmStdABRCDF | read-write | mandatory | Cutoff Decrease Factor. This unitless value has to be inversed to arrive at the actual value. The valid values possible are 0 and only powers of 2; i.e. 1, 2, … |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.10 | ColumnausmStdABRADTF | read-write | mandatory | ACR Decrease Time Factor. Unit of this value is milliseconds. Granularity allowed is 10 milli seconds. The SNMP agent has to verify this compliance. |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.11 | ColumnausmStdABRICR | read-write | mandatory | Initial cell Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1, IMA T1, IMA E1 (normal) or IM… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.12 | ColumnausmStdABRMCR | read-write | mandatory | Minimum cell Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1 IMA E1 (normal) or IMA E1 (cle… |
| 1.3.6.1.4.1.351.110.5.2.2.1.4.1.13 | ColumnausmStdABRPCR | read-write | mandatory | Peak cell Rate. The actual value depends on the speed of the logical port (which can be a T1, E1 (normal), E1 (clear), IMA T1 IMA E1 (normal) or IMA E1 (clear)… |
| 1.3.6.1.4.1.351.110.5.2.2.2 | NodeausmChanStateGrp | |||
| 1.3.6.1.4.1.351.110.5.2.2.2.1 | TableausmChanStateGrpTable | not-accessible | mandatory | Table of transmit/receive states of channels. |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1 | RowausmChanStateGrpEntry | not-accessible | mandatory | An entry for AusmChannelStateGrpEntry. |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.1 | ColumnausmStateChanNum | read-only | mandatory | Refers to the logical channel number. In AUSM (4-port card), the permissible range is from 16..271. |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.2 | ColumnausmChanState | read-only | mandatory | This variable indicates the state of the VC (channel) failed(4) is added to distinguish between alarm (when the connection segment is not actually broken) and … |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.3 | ColumnchanEgrXmtState | read-only | mandatory | indicates the status of port transmit(Egress) |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.4 | ColumnchanIngrRcvState | read-only | mandatory | indicates the status of port receive(Ingress) |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.5 | ColumnchanIngrXmtState | read-only | mandatory | This variable indicates the transmit state of the VC (channel) on the Cellbus side (Ingress) 1 - other 2- normal 3 - sendingAIS 4 - sendingFerf |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.6 | ColumnchanEgrRcvState | read-only | mandatory | This variable indicates the receiving state of the VC (channel) on the Cellbus side (Egress) 1 - other 2- normal 3 - receivingAIS 4 - receivingFERF |
| 1.3.6.1.4.1.351.110.5.2.2.2.1.1.7 | ColumnausmChanStatusBitMap | read-only | mandatory | This variable indicates the consolidated bit map of the channel alarm state. Individual bit positions are as defined below. Bit position Fail/Alarm Reason 0 Al… |
| 1.3.6.1.4.1.351.110.5.2.2.3 | NodeausmChanCntGrp | |||
| 1.3.6.1.4.1.351.110.5.2.2.3.1 | TableausmChanCntGrpTable | not-accessible | mandatory | The config table is for logical channel interface there are 1000 entries for 8 logical ports. In AUSM (4-port card), a logical port is synonymous with a physic… |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1 | RowausmChanCntGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.1 | ColumnausmCntChanNum | read-only | mandatory | Refers to the logical channel number. In AUSM (4-port card), the permissible range is from 16..271. |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.2 | ColumnchanSecInService | read-only | mandatory | The number of seconds channel is in service |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.3 | ColumnchanCongestMinutes | read-only | mandatory | The number of minutes for which congestion was experienced |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.4 | ColumnchanIngrPeakQDepth | read-only | mandatory | Peak queue depth on the ingress direction |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.5 | ColumnchanIngrRcvCells | read-only | mandatory | The number of cells received in the Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.6 | ColumnchanIngrClpSetRcvCells | read-only | mandatory | The number of CLP set cells received in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.7 | ColumnchanIngrEfciSetRcvCells | read-only | mandatory | The number of EFCI set cells received in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.8 | ColumnchanIngrQfullDiscardCells | read-only | mandatory | The number of cells discarded due to ingress Q full |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.9 | ColumnchanIngrClpSetDiscardCells | read-only | mandatory | The number of CLP set cells discarded in Ingress direction |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.10 | ColumnchanIngrUpcClpSetCells | read-only | mandatory | The number of cells for which CLP was set by UPC |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.11 | ColumnchanIngrXmtCells | read-only | mandatory | The number of cells transmitted to the cellbus |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.12 | ColumnchanShelfAlarmDiscardCells | read-only | mandatory | The number of cells discarded due to Shelf Alarm |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.13 | ColumnausmChanClrButton | read-write | mandatory | writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.14 | ColumnchanEpdDiscCells | read-only | mandatory | The number of cells discarded due to EPD (Early Packet Discard) condition |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.15 | ColumnchanPpdDiscCells | read-only | mandatory | The number of cells discarded due to PPD (Partial Packet Discard) condition |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.16 | ColumnchanIngrRcvCellRate | read-only | mandatory | The number of cells received per second from the port. Statistics collected before UPC and ingress qeueing. The maximum value is 5000 because clear E1 rate is … |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.17 | ColumnchanIngrRcvUtilization | read-only | mandatory | The percentage utilization of the reserved bandwidth (PCR). Statistics collected before UPC and ingress queueing. The maximum value is 200 because a connection… |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.18 | ColumnchanIngrXmtCellRate | read-only | mandatory | The number of cells transmitted per second to the network. Statistics collected after UPC and ingress qeueing. |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.19 | ColumnchanIngrXmtUtilization | read-only | mandatory | The percentage utilization of the reserved bandwidth (PCR). Statistics collected after UPC and ingress queueing. |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.20 | ColumnchanEgrRcvCellRate | read-only | mandatory | The number of cells received per second from the network. Statistics collected before egress qeueing. |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.21 | ColumnchanEgrRcvUtilization | read-only | mandatory | The percentage utilization of the reserved bandwidth (PCR). Statistics collected before egress queueing. |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.22 | ColumnchanIngrXmtAAL5Frames | read-only | mandatory | This statistics provides a count of the number of AAL5 Frames that are sent to the network |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.23 | ColumnchanIngrEfciSetXmtCells | read-only | mandatory | This statistics provides a count of the number of EFCI set cells that are transmitted to the network. This statistis is collected after the policing and queuei… |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.24 | ColumnchanEgrPortQfullDiscardCells | read-only | mandatory | This statistics provides a count of the number of cells discarded because of Egress Port Queue full. This count is displayed for the queue corresponding to por… |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.25 | ColumnchanEgrPortQClpThresDiscardCells | read-only | mandatory | This statistics provides a count of the number of cells discarded because of Egress Port Queue CLP Threshold exceed. This count is displayed for the queue corr… |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.26 | ColumnchanTxFifoFullCnt | read-only | mandatory | This statistics provides a count of the number of times the AUSM card tried to send a cell, but was unable to send because the Transmit FIFO was full. Note tha… |
| 1.3.6.1.4.1.351.110.5.2.2.3.1.1.27 | ColumnchanIngrCurrQDepth | read-only | mandatory | Current queue depth on the ingress direction |
| 1.3.6.1.4.1.351.110.5.2.3 | NodeausmEndPointMapGrp | |||
| 1.3.6.1.4.1.351.110.5.2.3.1 | TableausmEndPointMapGrpTable | not-accessible | mandatory | For Ausm-4p There are 255 entries For Ausm-8p There are 1000 entries For PXM (MGX) There are 4096 entries Port Num and VpiVci will uniquely identify a row. |
| 1.3.6.1.4.1.351.110.5.2.3.1.1 | RowausmEndPointMapGrpEntry | not-accessible | mandatory | An entry in the table |
| 1.3.6.1.4.1.351.110.5.2.3.1.1.1 | ColumnausmEndPortNum | read-only | mandatory | Refers to the logical port on the board. In AUSM (4-port card), a logical port is synonymous with a physical port. In PXM, a port refers to the Logical Broadba… |
| 1.3.6.1.4.1.351.110.5.2.3.1.1.2 | ColumnendVpi | read-only | mandatory | The VPI value for the connection |
| 1.3.6.1.4.1.351.110.5.2.3.1.1.3 | ColumnendVci | read-only | mandatory | The VCI value for the connection |
| 1.3.6.1.4.1.351.110.5.2.3.1.1.4 | ColumnausmEndChanNum | read-only | mandatory | Refers to the logical connection for this port and VpiVci. In AUSM (4-port card), the permissible range is 16..271 In AUSM (8-port card), the permissible range… |
| 1.3.6.1.4.1.351.110.5.2.3.1.1.5 | ColumnendChanType | read-only | mandatory | Refers to the type of the connection for this Port and VpiVci |
| 1.3.6.1.4.1.351.110.5.2.5.1.1 | TableatmLineCnfTable | not-accessible | mandatory | The ATM Line config table is for the physical interface. There will an entry for each of the physical line. |
| 1.3.6.1.4.1.351.110.5.2.5.1.1.1 | RowatmLineCnfEntry | not-accessible | mandatory | An entry for the physical interface. |
| 1.3.6.1.4.1.351.110.5.2.5.1.1.1.1 | ColumnatmLineCnfNum | read-only | mandatory | Refers to the phsical line number, PXM port will have a maximum of 4 lines. |
| 1.3.6.1.4.1.351.110.5.2.5.1.1.1.2 | ColumnatmLineInterfaceFormat | read-write | mandatory | This indicates the format of the cells going out on the physical interface |
| 1.3.6.1.4.1.351.110.5.2.5.2.1 | TableatmLineCntTable | not-accessible | mandatory | The ATM Line count table is for the physical interface. There will an entry for each of the physical line. |
| 1.3.6.1.4.1.351.110.5.2.5.2.1.1 | RowatmLineCntEntry | not-accessible | mandatory | An entry for the physical interface. These are counts which are collected on a physical line basis. |
| 1.3.6.1.4.1.351.110.5.2.5.2.1.1.1 | ColumnatmLineNum | read-only | mandatory | Refers to the phsical line number, PXM port will have a maximum of 4 lines. |
| 1.3.6.1.4.1.351.110.5.2.5.2.1.1.2 | ColumnatmLineTotalRcvCells | read-only | mandatory | The number of cells received in Ingress direction. |
| 1.3.6.1.4.1.351.110.5.2.5.2.1.1.3 | ColumnatmLineTotalXmtCells | read-only | mandatory | The number of cells transmitted in the egress direction |
| 1.3.6.1.4.1.351.110.5.2.5.2.1.1.4 | ColumnatmLineRcvHecErrorCells | read-only | mandatory | Number of cells with HEC error |
| 1.3.6.1.4.1.351.110.5.2.5.2.1.1.5 | ColumnatmLineCntClrButton | read-write | mandatory | writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.6.1.1 | NodebbIfCnfPortGrp | |||
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1 | TablebbIfCnfPortGrpTable | not-accessible | mandatory | The Broadband Interface config table is for logical interface. There will an entry for each of the logical partition of the physical line. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1 | RowbbIfCnfPortGrpEntry | not-accessible | mandatory | An entry for the logical interface. The interface may be further be configured to be used as a virtual trunk OR as a UNI Port. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.1 | ColumnbbIfNum | read-only | mandatory | This is logical interface number within a physical line num. In MGX PXM card, a physical port can have a maximum of 32 logical interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.2 | ColumnbbIfRowStatus | read-write | mandatory | This variable enables or disables the logical interface. 1 - enable 2 - disable 3 - modify |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.3 | ColumnbbIfAdmin | read-write | mandatory | This variable enables or disables the logical interface. 1 - up 2 - down 3 - writeOnly |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.4 | ColumnbbIfLineNum | read-write | mandatory | The line number associated with the logical interface. For PXM, there is currently 4 physical lines. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.5 | ColumnbbIfIngrPctBandwidth | read-write | mandatory | The percentage of aggregate physical line bandwidth, available for this broadband interface - Ingress. Default is 0 % |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.6 | ColumnbbIfEgrPctBandwidth | read-write | mandatory | The percentage of aggregate physical line bandwidth, available for this broadband interface - Egress . Default is 0 % |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.7 | ColumnbbIfMinVpi | read-write | mandatory | The lower limit of VPI range to be reserved for this logical interface. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.8 | ColumnbbIfMaxVpi | read-write | mandatory | The upper limit of VPI range to be reserved for this logical interface. For virtual trunks, bbIfMinVpi and bbIfMaxVpi should be the same. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.9 | ColumnbbIfSpeed | read-only | mandatory | The speed of the port in cells per second |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.10 | ColumnbbIfMaxCellRatePct | read-write | mandatory | The maximum cell rate allowed for the port in terms of percentage. Must be greater than or equal to bbIfIngrPctBandwidth. The default is 100 percent. |
| 1.3.6.1.4.1.351.110.5.2.6.1.1.2 | ScalarnextBbIfNumAvailable | read-only | mandatory | Indicates the next logical broadband interface number that is available |
| 1.3.6.1.4.1.351.110.5.2.6.1.2 | NodebbIfCnfSigILMIGrp | |||
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1 | TablebbIfCnfSigILMIGrpTable | not-accessible | mandatory | The config table is for upto 32 logical port interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1 | RowbbIfCnfSigILMIGrpEntry | not-accessible | mandatory | An entry for a boradband interface used as a UNI port. In MGX PXM card, a physical port can have a maximum of 32 logical interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.1 | ColumnbbIfSigPortNum | read-only | mandatory | Refers to the logical interface index on the PXM card in MGX node. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.2 | ColumnbbIfIlmiEnable | read-write | mandatory | The logical interface is a generic entity, it can be used as either a virtual trunk, or user port with UNI support. This variable is provided to enable/disable… |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.3 | ColumnbbIfSignallingProtocolType | read-write | mandatory | This will set the signalling protocol 1 - other 2 - noSignalling 3 - ILMI |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.4 | ColumnbbIfSignallingVpi | read-write | mandatory | Indicates the VPI on which signalling cells arrive. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.5 | ColumnbbIfSignallingVci | read-write | mandatory | Indicates the VCI on which signalling cells arrive. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.6 | ColumnbbIfAddrPrefix | read-write | mandatory | Network Prefix for the ATM address |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.7 | ColumnbbIfCustomerId | read-write | mandatory | For the INS as a read/write variable |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.8 | ColumnbbIfProtocolRevNo | read-write | mandatory | For the INS as a read/write variable. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.9 | ColumnbbIfIlmiTrapEnable | read-write | mandatory | Enable/disable ILMI Trap sending |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.10 | ColumnbbIfMinTrapInterval | read-write | mandatory | Number of seconds between traps. |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.11 | ColumnbbIfKeepAlivePollingEnable | read-write | mandatory | Enable/disable Keep Alive Polling |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.12 | ColumnbbIfErrorThresholdN491 | read-write | mandatory | Error Threshold (N491) value |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.13 | ColumnbbIfEventThresholdN492 | read-write | mandatory | Event Threshold (N492) value |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.14 | ColumnbbIfPollingIntervalT491 | read-write | mandatory | Polling Interval (T491) value |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.15 | ColumnbbIfMinEnquiryIntervalT493 | read-write | mandatory | Minimum Enquiry Interval (T493) |
| 1.3.6.1.4.1.351.110.5.2.6.1.2.1.1.16 | ColumnbbIfAddrRegEnable | read-write | mandatory | Enable/disable ILMI Address Registration |
| 1.3.6.1.4.1.351.110.5.2.6.2.1 | TablebbIfCnfRscPartGrpTable | not-accessible | mandatory | The config table is for logical port interface There can be 32 entries for PXM card in MGX. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1 | RowbbIfCnfRscPartGrpEntry | not-accessible | mandatory | An entry for a logical interface |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.1 | ColumnbbRscPartIfNum | read-only | mandatory | This is logical interface number. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.2 | ColumnbbRscPartCtrlrNum | read-only | mandatory | This is index for controller using the interface . 1 - PAR 2 - PNNI 3 - TAG |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.3 | ColumnbbIfRscPrtRowStatus | read-write | mandatory | This will add, delete or modify the partition. 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.4 | ColumnbbIfRscPrtInUse | read-write | mandatory | Setting this object to 1 indicates that the resources (LCN/Local VPID/VCI/VPI) have been partitioned and INS, network ctrlrs.,SV+ are currently using this info… |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.5 | ColumnbbIfRscPrtIngrPctBandwidth | read-write | mandatory | The percentage of logical interface bandwidth ( bbIfIngrPctBandwidth ), available for UNI channels. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.6 | ColumnbbIfRscPrtEgrPctBandwidth | read-write | mandatory | The percentage of logical interface bandwidth ( bbIfIngrPctBandwidth ), available for UNI channels. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.7 | ColumnbbIfRscPrtVpiLow | read-write | mandatory | The beginning of the VPI range reserved for this partition. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.8 | ColumnbbIfRscPrtVpiHigh | read-write | mandatory | The end of the VPI range reserved for this partition. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.9 | ColumnbbIfRscPrtVciLow | read-write | mandatory | The beginning of the VCI range reserved for this partition. This field is only valid for logical interfaces configured with a single VPI. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.10 | ColumnbbIfRscPrtVciHigh | read-write | mandatory | The end of the VCI range reserved for this partition. This field is only valid for logical interfaces configured with a single VPI. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.11 | ColumnbbIfRscPrtVpidLow | read-write | mandatory | The beginning of the VPID range reserved for partition. Used for VP conn.s |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.12 | ColumnbbIfRscPrtVpidHigh | read-write | mandatory | The end of the VPID range reserved for partition. Used for VP conn.s |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.13 | ColumnbbIfRscPrtMaxChans | read-write | mandatory | This represents no. of channels that are available to the controller. |
| 1.3.6.1.4.1.351.110.5.2.6.2.1.1.14 | ColumnbbIfRscPartCtrlrID | read-write | mandatory | This is the controller identifier for resource patition. The default value is set for PNNI controller. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1 | TablebbIfStateGrpTable | not-accessible | mandatory | The state table for the logical interface there can be 32 entries for the PXM card in MGX. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1.1 | RowbbIfStateGrpEntry | not-accessible | mandatory | An entry for logical interface. In MGX PXM card, a physical port can have a maximum of 32 logical interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1.1.1 | ColumnbbStateIfNum | read-only | mandatory | This is logical interface number within a physical line num. In MGX PXM card, a physical port can have a maximum of 32 logical interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1.1.2 | ColumnbbIfState | read-only | mandatory | This variable indicates the status of the logical interface. The following are not supported for the logical interface. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1.1.3 | ColumnbbIfOversubscribed | read-only | mandatory | This variable indicates the whether the logical interface is over subscribed or not. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1.1.4 | ColumnbbIfIngrPercentUtil | read-only | mandatory | Percentage Utilization of the interface in the Ingress direction. |
| 1.3.6.1.4.1.351.110.5.2.6.3.1.1.5 | ColumnbbIfEgrPercentUtil | read-only | mandatory | Percentage Utilization of the interface in the Egress direction. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1 | NodebbIfCntGrp | |||
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1 | TablebbIfCntGrpTable | not-accessible | mandatory | The Broadband Interface Count table is for logical interface. There will an entry for each of the logical partition of the physical line. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1 | RowbbIfCntGrpEntry | not-accessible | mandatory | An entry for logical interface. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.1 | ColumnbbCntIfNum | read-only | mandatory | Refers to the logical interface index on the PXM card in MGX node. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.2 | ColumnbbIfTotalCells | read-only | mandatory | Total number of cells (VC plus Qbin) that belong to this Interface. This maps on to the virtual interface of QE. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.3 | ColumnbbIfRcvValidOAMCells | read-only | mandatory | Total number of OAM cell received. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.4 | ColumnbbIfRcvRmCells | read-only | mandatory | Total number of RM cells Received. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.5 | ColumnbbIfRcvClp0Cells | read-only | mandatory | Total number of CLP-0 cells Received. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.6 | ColumnbbIfRcvClp1Cells | read-only | mandatory | Total number of CLP-1 cells Received. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.7 | ColumnbbIfRcvClp0DiscCells | read-only | mandatory | Total number of CLP-0 cells discarded at Ingress. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.8 | ColumnbbIfRcvClp1DiscCells | read-only | mandatory | Total number of CLP-1 cells discarded at Ingress. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.9 | ColumnbbIfXmtOAMCells | read-only | mandatory | Total number of OAM cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.10 | ColumnbbIfXmtRmCells | read-only | mandatory | Total number of RM cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.11 | ColumnbbIfXmtClp0Cells | read-only | mandatory | Total number of CLP-0 cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.12 | ColumnbbIfXmtClp1Cells | read-only | mandatory | Total number of CLP-1 cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.13 | ColumnbbIfCntClrButton | read-write | mandatory | Writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.6.4.2 | NodebbIfCntSigILMIGrp | |||
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1 | TablebbIfCntSigILMIGrpTable | not-accessible | mandatory | The counter table is for upto 32 logical port interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1 | RowbbIfCntSigILMIGrpEntry | not-accessible | mandatory | An entry for a boradband interface used as a UNI port. In MGX PXM card, a physical port can have a maximum of 32 logical interfaces. |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.1 | ColumnsigCntBbIfNum | read-only | mandatory | Refers to the logical interface index on the PXM card in MGX node. |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.2 | ColumnbbIfSnmpPduReceived | read-only | mandatory | The number of snmp packets received on this logical interface. |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.3 | ColumnbbIfGetRequestReceived | read-only | mandatory | The number of get request messages received |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.4 | ColumnbbIfGetNextRequestReceived | read-only | mandatory | The number of get-next messages received |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.5 | ColumnbbIfSetRequestReceived | read-only | mandatory | The number of set messages received |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.6 | ColumnbbIfTrapReceived | read-only | mandatory | The number of traps received |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.7 | ColumnbbIfGetResponseReceived | read-only | mandatory | The number of Keep Alive response messages received |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.8 | ColumnbbIfGetResponseTransmitted | read-only | mandatory | The number of response messages transmitted |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.9 | ColumnbbIfGetRequestTransmitted | read-only | mandatory | The number of Keep Alive get request messages transmitted |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.10 | ColumnbbIfTrapTransmitted | read-only | mandatory | The number of trap messages transmitted |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.11 | ColumnbbIfInvalidPDUReceived | read-only | mandatory | The number of invalid PDUs received |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.12 | ColumnbbIfAsn1ParseError | read-only | mandatory | The number of parse errors on ASN.1 |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.13 | ColumnbbIfNoSuchNameError | read-only | mandatory | The number of errors for name not present |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.14 | ColumnbbIfTooBigError | read-only | mandatory | The number of messages received with len > 484 |
| 1.3.6.1.4.1.351.110.5.2.6.4.2.1.1.15 | ColumnbbIfSigCntClrButton | read-write | mandatory | Writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.7.1.1 | TablebbChanCnfGrpTable | not-accessible | mandatory | The Broadband Channel config table is for a channel on logical interface. There will an entry for each of the channel added on the logical partition of the phy… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1 | RowbbChanCnfGrpEntry | not-accessible | mandatory | The config table is for logical channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.1 | ColumnbbChanCnfNum | read-only | mandatory | This identifies a channel on the PXM logical interface, used as PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.2 | ColumnbbChanRowStatus | read-write | mandatory | This will add, delete or modify the channel 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.3 | ColumnbbChanConnType | read-write | mandatory | This specifies the connection type 1 ==> Virtual Path Connection 2 ==> Virtual Channel Connection |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.4 | ColumnbbChanServiceType | read-write | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Available Bit Rate 4 ==> Unspecified Bit Rate 5 ==> Variable Bit Rate - R… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.5 | ColumnbbChanConnDesc | read-write | mandatory | A string that has been defined to give a descriptive name to the connection |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.6 | ColumnbbChanSvcFlag | read-write | mandatory | This specifies the connection type 1 ==> SVC connection 2 ==> PVC connection, used by PAR 3 ==> Soft PVC connection, used by PNNI |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.7 | ColumnbbChanSvcConnId | read-write | mandatory | This connection ID is for future use Currently not supported. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.8 | ColumnbbChanIfNum | read-write | mandatory | Channel's logical Interface from which traffic of the connection will be received. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.9 | ColumnbbChanVpi | read-write | mandatory | VPI for the connection. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.10 | ColumnbbChanVci | read-write | mandatory | VCI for the connection. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.11 | ColumnbbChanUpcEnable | read-write | mandatory | enables/disables UPC for Ingress cells |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.12 | ColumnbbChanUpcPCR | read-write | mandatory | PCR(0+1), Peak Cell Rate, specifies an upper bound on rate at which traffic can be submitted on an ATM connection. This object applies to the First Leaky Bucke… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.13 | ColumnbbChanUpcCDVT | read-write | mandatory | Compliant Cell Delay Variation. Also known as CDVT(0+1), Cell Delay Variation Tolerance, which specifies the maximum time period for accumulated violations of … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.14 | ColumnbbChanUpcSCR | read-write | mandatory | SCR, Sustainable Cell Rate, is an upper bound on the conforming average rate of an ATM connection, over time scales which are long relative to those for which … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.15 | ColumnbbChanUpcMBS | read-write | mandatory | Maximum Burst Size (MBS). Also known as Compliant Burst Size (CBS). . Units: cells . Applicable connection types: . VBR, ABR . Default: 1000 . Range : 1-5000000 |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.16 | ColumnbbChanGcra1Action | read-write | mandatory | GCRA1 Action. 1 = No Action 2 = Tag Untagged cells 3 = Tag untagged cells and discard tagged cells 4 = Discard all (0+1) non-comforming cells |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.17 | ColumnbbChanGcra2Action | read-write | mandatory | GCRA2 Action. 1 = No Action 2 = Tag Untagged cells 3 = Tag untagged cells and discard tagged cells 4 = Discard all (0+1) non-comforming cells |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.18 | ColumnbbChanUpcSCRPolicing | read-write | mandatory | Selects SCR policing for CLP = 0 or all cells |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.19 | ColumnbbChanEfciThreshold | read-write | mandatory | Threshold above which EFCI bit is to be set. Default Value is 3/4 of max cell count. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.20 | ColumnbbChanDiscardOption | read-write | mandatory | Enable Frame Discard or CLP Hysteresis. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.21 | ColumnbbChanFrmDiscardThreshold | read-write | mandatory | Ingress Frame Discard Threshold. Valid only when Ingress Frame Discard option is selected. Default Value : TBD |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.22 | ColumnbbChanClpHiThreshold | read-write | mandatory | Ingress CLP High Threshold. Default is 3/4 of max cell count. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.23 | ColumnbbChanClpLoThreshold | read-write | mandatory | Ingress CLP Low Threshold. Valid only when Ingress CLP Hysteresis option is selected. Default Value is 1/2 of max cell count. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.24 | ColumnbbChanCongstUpdateCode | read-write | mandatory | Ingress Channel Congestion Update Code. Default Value : TBD |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.25 | ColumnbbChanMaxCellMemThreshold | read-write | mandatory | Maximum number of cells of that connection in the memory. Assuming Total Cell Memory is 512K cells, this is defaulted to half of total size. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.26 | ColumnbbChanIngrPercentUtil | read-write | mandatory | Percentage Utilization of the IngrService Rate. This is used for connection admission control. Default Value : TBD |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.27 | ColumnbbChanEgrPercentUtil | read-write | mandatory | Percentage Utilization of the EgrService Rate. This is used for egress bandwidth calculation and connection admission control. Default Value : TBD |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.28 | ColumnbbChanEgrSrvRate | read-write | mandatory | Egress service rate - This is used for egress bandwidth calculation and for connection admission control. The actual value depends on the speed of the logical … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.29 | ColumnbbChanOvrSubOvrRide | read-write | mandatory | Channel Over Subscrive Override This MIB variable allows one to add a new connection on a port even if it is over subscribed. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.30 | ColumnbbChanLocalVpi | read-only | mandatory | The VPI value for this channel |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.31 | ColumnbbChanLocalVci | read-only | mandatory | The VCI value for this channel |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.32 | ColumnbbChanLocalNsapAddr | read-write | mandatory | The Near End NSAP Address value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.33 | ColumnbbChanRemoteVpi | read-write | mandatory | The VPI value for this channel |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.34 | ColumnbbChanRemoteVci | read-write | mandatory | The VCI value for this channel |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.35 | ColumnbbChanRemoteNsapAddr | read-write | mandatory | The Far End NSAP Address value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.36 | ColumnbbChanMaster | read-write | mandatory | This is used by the PXM switch platform module, to determine if this endpoint ia master or slave. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.37 | ColumnbbChanRtePriority | read-write | mandatory | This is also known as class of service, it is used by PXM to determine how important this connection is when selecting connections to route. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.38 | ColumnbbChanMaxCost | read-write | mandatory | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.39 | ColumnbbChanRestrictTrkType | read-write | mandatory | Restricted trunk type for routind, used by PXM. It specifies that the connection either cannot be routed over satellite trunks or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.40 | ColumnbbChanTestType | read-write | mandatory | The chanTestType starts testing the continuity or delay of a connection. It sends specific cell patterns toward the network and the terminating end of this con… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.41 | ColumnbbChanTestState | read-only | mandatory | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.42 | ColumnbbChanTestResult | read-only | mandatory | This is round trip delay in milliseconds. When you select testdelay option for the chanTestType, the result of the test that is measured in milliseconds can be… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.43 | ColumnbbChanTestTypeCPESide | read-write | mandatory | The default is notest. The chanTestType starts testing the segment continuity of a connection. It sends OAM Segment loopback cell towards port side (CPE) The C… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.44 | ColumnbbChanTestStateCPESide | read-only | mandatory | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.45 | ColumnbbConnVpcFlag | read-write | mandatory | This represents the connection type, used for PXM to identify VPC/VCC |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.46 | ColumnbbConnServiceType | read-write | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 4 ==> Unspecified Bit Rate 6 ==> Available Bit Rate ( standard ) 8 ==> Variable… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.47 | ColumnbbConnPCR | read-write | mandatory | Peak cell rate, could be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.48 | ColumnbbConnSCR | read-write | mandatory | Sustained cell rate, could be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.49 | ColumnbbConnPercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by this end-point. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.50 | ColumnbbRemoteConnPCR | read-write | mandatory | Peak cell rate of the other end, if not set, will be set to the same as local end PCR (bbChanUpcPCR). However, note that if the PCRs for both local and remote … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.51 | ColumnbbRemoteConnSCR | read-write | mandatory | Sustained cell rate of the other end, if not set, will be set to the same as local end SCR (bbChanUpcSCR). However, note that if the PCRs for both local and re… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.52 | ColumnbbRemoteConnPercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by this end-point. If this is not specified in the connection setup request, it'll be defaulted to 10… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.53 | ColumnbbChanUpcMCR | read-write | mandatory | SCR, Sustainable Cell Rate, is an upper bound on the conforming average rate of an ATM connection, over time scales which are long relative to those for which … |
| 1.3.6.1.4.1.351.110.5.2.7.1.2 | ScalarbbChanNumNextAvailable | read-only | mandatory | This variable contains the next unused channel number of the possible 4096 . This number can be used in channel config table. ChanNumNextAvailable gets updated… |
| 1.3.6.1.4.1.351.110.5.2.7.1.3 | ScalarbbChanVpIdNextAvailable | read-only | mandatory | This in only valid for a Service Module, will NOT be used in PXM. This variable contains the next unused local VPId of the possible 1 to 4095. This number can … |
| 1.3.6.1.4.1.351.110.5.2.7.2.1 | TablebbChanStateGrpTable | not-accessible | mandatory | The Broadband Channel state table is for a channel on logical interface. There will an entry for each of the channel added on the logical partition of the phys… |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1 | RowbbChanStateGrpEntry | not-accessible | mandatory | The state table is for logical channel. The available number of channels on the broadband interface (user ports) on the PXM card is restricted to 4K. The PXM c… |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.1 | ColumnbbChanStateNum | read-only | mandatory | Refers to the logical channel number |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.2 | ColumnbbChanState | read-only | mandatory | This variable indicates the state of the VC (channel). |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.3 | ColumnbbChanEgrXmtState | read-only | mandatory | Indicates the status of port transmit(Egress) |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.4 | ColumnbbChanIngrRcvState | read-only | mandatory | indicates the status of port receive(Ingress) |
| 1.3.6.1.4.1.351.110.5.2.7.3.1 | TablebbChanCntGrpTable | not-accessible | mandatory | The Broadband Channel count table is for a channel on virtual interface or a physical line. There will an entry for each of the channel added on the logical pa… |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1 | RowbbChanCntGrpEntry | not-accessible | mandatory | The count table is for logical channel. The available number of channels on the broadband interface on the PXM card is restricted to 4K. The PXM card has 2 Que… |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.1 | ColumnbbChanCntNum | read-only | mandatory | Channel number. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.2 | ColumnbbChanRcvClp0Cells | read-only | mandatory | CLP_0 Cells Received From Port Count. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.3 | ColumnbbChanRcvClp1Cells | read-only | mandatory | CLP_1 Cells Received From Port Count. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.4 | ColumnbbChanNonConformCellsAtGcra1Policer | read-only | mandatory | Non-Conforming Cells Received at Ingress GCRA1 Policer Count. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.5 | ColumnbbChanNonConformCellsAtGcra2Policer | read-only | mandatory | Non-Conforming Cells Received at Ingress GCRA2 Policer Count. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.6 | ColumnbbChanRcvEOFCells | read-only | mandatory | Number of cells received from PXM port with EOF set. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.7 | ColumnbbChanDscdClp0Cells | read-only | mandatory | Number of discarded clp = 0 cells received from PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.8 | ColumnbbChanDscdClp1Cells | read-only | mandatory | Number of discarded clp = 1 cells received from PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.9 | ColumnbbChanRcvCellsSent | read-only | mandatory | Number of cells received from port and sent out of the Queue Engine. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.10 | ColumnbbChanXmtClp0Cells | read-only | mandatory | Number of cells with EFCI clear transmitted to PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.11 | ColumnbbChanXmtClp1Cells | read-only | mandatory | Number of cells with EFCI set transmitted to PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.12 | ColumnbbChanDscdClpZeroCellsToPort | read-only | mandatory | Number of discard CLP = 0 cells before transmitted to PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.13 | ColumnbbChanDscdClpOneCellsToPort | read-only | mandatory | Number of discard CLP = 1 cells before transmitted to PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.3.1.1.14 | ColumnbbChanCntClrButton | read-write | mandatory | Writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.2.8.1 | NodevirtualInterfaceCnf | |||
| 1.3.6.1.4.1.351.110.5.2.8.1.1 | TablevrtlIntrConfigTable | not-accessible | mandatory | Virtual Interface Configuration Table |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1 | RowvrtlIntrConfigEntry | not-accessible | mandatory | An entry in the Virtual Interface configuration Table |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.1 | ColumnconfigVrtlIntrNum | read-only | mandatory | Virtual Interface Number. There are totaly 32 Virtual Interfaces on the card (egress). |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.2 | ColumnvrtlIntrPortNum | read-write | mandatory | Port number which will be connected to the Virtual Interface. Value zero meens that this virtual interface is not connected to any port. |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.3 | ColumnvrtlIntrState | read-write | mandatory | Virtual Interface State. |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.4 | ColumnvrtlIntrMaxQueMem | read-write | mandatory | Virtual Interface's Max queue memory. 1 = 4Kcells 2 = 8Kcells 3 = 16Kcells 4 = 32Kcells 5 = 64Kcells 6 = 128Kcells 7 = 256Kcells 8 = 512Kcells |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.5 | ColumnvrtlIntrMinCellRate | read-write | mandatory | Virtual Interface's minimum cell rate. The default value: for OC12 port is 1412832 cells/sec for OC3 port is 353208 cells/sec for T3 port is 96000 cells/sec fo… |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.6 | ColumnvrtlIntrMaxCellRate | read-write | mandatory | Virtual Interface's maximum cell rate. The default value: for OC12 port is 1412832 cells/sec for OC3 port is 353208 cells/sec for T3 port is 96000 cells/sec fo… |
| 1.3.6.1.4.1.351.110.5.2.8.1.1.1.7 | ColumnvrtlIntrCurrConfigPaths | read-only | mandatory | This is not a configurable parameter. This gives the count of paths currently configured on this VI. |
| 1.3.6.1.4.1.351.110.5.2.8.2 | NodevirtualInterfaceCnt | |||
| 1.3.6.1.4.1.351.110.5.2.8.2.1 | TablevrtlIntrCounterTable | not-accessible | mandatory | Virtual Interface Counters Table. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1 | RowvrtlIntrCounterEntry | not-accessible | mandatory | An entry in the Virtual Interface Counter Table. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.1 | ColumncountVrtlIntrNum | read-only | mandatory | Virtual Interface Number. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.2 | ColumnvrtlIntrTotalCellCnt | read-only | mandatory | Total number of cells (VC plus Qbin) that belong to this Virtual Interface. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.3 | ColumnvrtlIntrTotalQbinCellCnt | read-only | mandatory | Total number of cells in the Qbin belonging to this Virtual Interface. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.4 | ColumnvrtlIntrRxdValidOAMCellCnt | read-only | mandatory | Total number of OAM cell received. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.5 | ColumnvrtlIntrRxdRmCellCnt | read-only | mandatory | Total number of RM cells Received. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.6 | ColumnvrtlIntrRxdClpUntaggedCellCnt | read-only | mandatory | Total number of CLP-0 cells Received. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.7 | ColumnvrtlIntrRxdClpTaggedCellCnt | read-only | mandatory | Total number of CLP-1 cells Received. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.8 | ColumnvrtlIntrRxdClpUntaggedDiscardedCellCnt | read-only | mandatory | Total number of CLP-0 cells discarded at Ingress. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.9 | ColumnvrtlIntrRxdClpTaggedDiscardedCellCnt | read-only | mandatory | Total number of CLP-1 cells discarded at Ingress. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.10 | ColumnvrtlIntrXmtdOAMCellCnt | read-only | mandatory | Total number of OAM cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.11 | ColumnvrtlIntrXmtdRmCellCnt | read-only | mandatory | Total number of RM cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.12 | ColumnvrtlIntrXmtdClpUntaggedCellCnt | read-only | mandatory | Total number of CLP-0 cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.8.2.1.1.13 | ColumnvrtlIntrXmtdClpTaggedCellCnt | read-only | mandatory | Total number of CLP-1 cells transmitted. |
| 1.3.6.1.4.1.351.110.5.2.8.3 | NodevirtualInterfaceQbinCnf | |||
| 1.3.6.1.4.1.351.110.5.2.8.3.1 | TablevrtlIntrQbinConfigTable | not-accessible | mandatory | Virtual Interface QBin Configuration Table. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1 | RowvrtlIntrQbinConfigEntry | not-accessible | mandatory | An entry in the Virtual Interface Qbin Config Table. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.1 | ColumnqueConfigVrtlIntrNum | read-only | mandatory | Virtual Interface Number. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.2 | ColumnqueConfigVrtlIntrQbinNum | read-only | mandatory | Virtual Interface Qbin Number. There are totaly 16 Qbin per Virtual Interface. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.3 | ColumnvrtlIntrQbinState | read-write | mandatory | Virtual Interface QBIN state. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.4 | ColumnvrtlIntrQbinPri | read-write | mandatory | This indicates the priority of the QBIN service within the Virtual Interface. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.5 | ColumnvrtlIntrQbinRate | read-write | mandatory | The rate at which cells in the QBIN are serviced. Max Cell rate for OC3 interface is 353208 cell/sec. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.6 | ColumnvrtlIntrQbinDiscardSelection | read-write | mandatory | Virtual Interface QBin Congestion control option. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.7 | ColumnvrtlIntrQbinMaxThreshold | read-write | mandatory | Max cells that can be queued in the QBIN. The Get value will be different from the Set value because of FW internal round up. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.8 | ColumnvrtlIntrQbinClpHiThreshold | read-write | mandatory | The threshold above which the tagged cells will be dropped. The Get value will be different from the Set value because of FW internal round up. |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.9 | ColumnvrtlIntrQbinClpLoThreshold | read-write | mandatory | Valid only if congestion control is set to CLP hysterises. The threshold upto which the dropping of the tagged cells should continue once it has crossed CLP HI… |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.10 | ColumnvrtlIntrQbinFrameDiscardThreshold | read-write | mandatory | Valid only if congestion control is set to Frame Discard. It is the threshold after which the QE will start discarding the entire frame if one or more cells of… |
| 1.3.6.1.4.1.351.110.5.2.8.3.1.1.11 | ColumnvrtlIntrQbinEfciThreshold | read-write | mandatory | The threshold above which the EFCI bits of the cell is set. The Get value will be different from the Set value because of FW internal round up. |
| 1.3.6.1.4.1.351.110.5.2.8.4 | NodevirtualInterfaceQbinCnt | |||
| 1.3.6.1.4.1.351.110.5.2.8.4.1 | TablevrtlIntrQbinCounterTable | not-accessible | mandatory | Virtual Interface QBin Counter Table. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1 | RowvrtlIntrQbinCounterEntry | not-accessible | mandatory | An entry in the Virtual Interface Qbin Counter Table. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1.1 | ColumnqueConuterVrtlIntrNum | read-only | mandatory | Virtual Interface Number. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1.2 | ColumnqueCounterVrtlIntrQbinNum | read-only | mandatory | Virtual Interface Qbin Number. There are totaly 16 Qbin per Virtual Interface. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1.3 | ColumnvrtlIntrQbinCurrentCellCnt | read-only | mandatory | Total number of cells currently in the Qbin. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1.4 | ColumnvrtlIntrQbinRxdCellCnt | read-only | mandatory | Total number of cells arrived to the QBIN. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1.5 | ColumnvrtlIntrQbinTxdCellCnt | read-only | mandatory | Total number of cells departured from QBIN. |
| 1.3.6.1.4.1.351.110.5.2.8.4.1.1.6 | ColumnvrtlIntrQbinDiscardedCellCnt | read-only | mandatory | Total number of arrivals to QBIN which were discarded. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1 | TablerpmPortTable | not-accessible | mandatory | List of RPM backplane sub-interfaces. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1 | RowrpmPortEntry | not-accessible | mandatory | An entry for the RPM backplane sub interface. Each entry contains RPM's backplane sub interface number, its IP address and ATM address. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.1 | ColumnrpmPortSlotNum | read-only | mandatory | Specifies the slot number of the RPM card. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.2 | ColumnrpmPortInterface | read-only | mandatory | This is the RPM's backplane interface. Currently there is only one interface. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.3 | ColumnrpmPortSubInterface | read-only | mandatory | It identifies a sub-interface. (SNMP doent support index value 0) sub-interface starts from 1. The sub-interface 0 in CLI will be 1 here. So sub-interface is i… |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.4 | ColumnrpmPortRowStatus | read-only | mandatory | This indicates the status of this sub-interface. 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.5 | ColumnrpmPortIpAddress | read-only | mandatory | IP address of the sub-interface. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.6 | ColumnrpmPortSubNetMask | read-only | mandatory | SUB-NETMASK of the sub-interface. |
| 1.3.6.1.4.1.351.110.5.2.9.1.1.1.7 | ColumnrpmPortState | read-only | mandatory | This indicates the state of this sub-interface. 1 ==> notConfigured 2 ==> active 3 ==> failed. Currently 'failed' state is not supported. |
| 1.3.6.1.4.1.351.110.5.2.9.2 | NoderpmIfCnfResPart | |||
| 1.3.6.1.4.1.351.110.5.2.9.2.1 | TablerpmIfCnfRscPartTable | not-accessible | mandatory | The table is for RPM interface resource partition. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1 | RowrpmIfCnfRscPartEntry | not-accessible | mandatory | An entry for a logical interface |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.1 | ColumnrpmIfRscSlotNum | read-only | mandatory | Specifies the slot number of the RPM card. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.2 | ColumnrpmIfRscPartIfNum | read-only | mandatory | This is backplane interface number. Currently there is only one interface. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.3 | ColumnrpmIfRscPartCtrlrNum | read-only | mandatory | This is index for controller using the interface . 1 - PAR 2 - PNNI 3 - TAG |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.4 | ColumnrpmIfRscPrtRowStatus | read-only | mandatory | This will add, delete or modify the partition. 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.5 | ColumnrpmIfRscPrtIngrPctBandwidth | read-only | mandatory | The percentage of logical interface bandwidth. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.6 | ColumnrpmIfRscPrtEgrPctBandwidth | read-only | mandatory | The percentage of logical interface bandwidth. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.7 | ColumnrpmIfRscPrtVpiLow | read-only | mandatory | The beginning of the VPI range reserved for this partition. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.8 | ColumnrpmIfRscPrtVpiHigh | read-only | mandatory | The end of the VPI range reserved for this partition. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.9 | ColumnrpmIfRscPrtVciLow | read-only | mandatory | The beginning of the VCI range reserved for this partition. This field is only valid for logical interfaces configured with a single VPI. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.10 | ColumnrpmIfRscPrtVciHigh | read-only | mandatory | The end of the VCI range reserved for this partition. This field is only valid for logical interfaces configured with a single VPI. |
| 1.3.6.1.4.1.351.110.5.2.9.2.1.1.11 | ColumnrpmIfRscPrtMaxChans | read-only | mandatory | This represents no. of channels that are available to the controller. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1 | TablerpmChanGrpTable | not-accessible | mandatory | The RPM channel table. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1 | RowrpmChanGrpEntry | not-accessible | mandatory | An entry for logical channel. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.1 | ColumnrpmChanSlotNum | read-only | mandatory | Specifies the slot number of the RPM card. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.2 | ColumnrpmChanInterface | read-only | mandatory | This is the RPM's backplane interface. Currently there is only one interface. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.3 | ColumnrpmChanNum | read-only | mandatory | This is the LCN. A unique number which identifies a connection. LCN maps VPI and VCI. For VCC, VCI range is 1..3825, and LCN range is 16..3840. LCN = VCI + 16.… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.4 | ColumnrpmChanRowStatus | read-only | mandatory | This indicates the status of this channel. 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.5 | ColumnrpmChanVcd | read-only | mandatory | Virtual Circuit Descriptor. A unique number which identifies a connection. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.6 | ColumnrpmChanVpi | read-only | mandatory | The VPI value for this channel. For VPC, VPI range is 1..255 and LCN range is 3841..4095. LCN = VPI + 3840 |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.7 | ColumnrpmChanVci | read-only | mandatory | The VCI value for this channel. For VCC, VCI range is 1..3825, and LCN range is 16..3840. LCN = VCI + 16. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.8 | ColumnrpmChanSubInterface | read-only | mandatory | This is the RPM's backplane sub-interface. (SNMP doent support index value 0) sub-interface starts from 1. The sub-interface 0 in CLI will be 1 here. So sub-in… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.9 | ColumnrpmChanLocalVpi | read-only | mandatory | This VPI together with the local VCI and NSAP represents the local end point in this connection. The VPI value is zero if it is a VCC conn. type. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.10 | ColumnrpmChanLocalVci | read-only | mandatory | This VCI together with the local VPI and NSAP represents the local end point in this connection. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.11 | ColumnrpmChanLocalNsap | read-only | mandatory | The Near End NSAP Address value for this channel. This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as node name, 2 bytes for Cisco ID, 1 byte rsvd,… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.12 | ColumnrpmChanRemoteVpi | read-only | mandatory | This VPI together with the remote VCI and NSAP represents the remote end point in this connection. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.13 | ColumnrpmChanRemoteVci | read-only | mandatory | This VCI together with the remote VPI and NSAP represents the remote end point in this connection. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.14 | ColumnrpmChanRemoteNsap | read-only | mandatory | The Far End NSAP Address value for this channel. This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 1 byte rsvd, 3 b… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.15 | ColumnrpmChanType | read-only | mandatory | This specifies the connection type 1 ==> SVC 2 ==> PVC 3 ==> Soft PVC Currently only PVC is supported. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.16 | ColumnrpmChanConnType | read-only | mandatory | This specifies the connection type 1 ==> Virtual Path Connection 2 ==> Virtual Channel Connection |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.17 | ColumnrpmChanServiceType | read-only | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard ABR 7 ==> fores… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.18 | ColumnrpmChanMastership | read-only | mandatory | This specifies which end of the connection is the master. This is used by PXM to determine if this end point is master or slave. Only in AXIS shelf, 'unknown' … |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.19 | ColumnrpmChanRtePriority | read-only | mandatory | This is also known as class of service, it is used by PXM to determine how important this connection is when selecting connections to route. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.20 | ColumnrpmChanMaxCost | read-only | mandatory | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.21 | ColumnrpmChanRestrictTrkType | read-only | mandatory | Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satellite trunks or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.22 | ColumnrpmChanPCR | read-only | mandatory | Peak cell rate.(in cells per sec.) |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.23 | ColumnrpmChanRemotePCR | read-only | mandatory | Peak cell rate of the other end, if not set, will be set to the same as local end PCR. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.24 | ColumnrpmChanMCR | read-only | mandatory | Minimum cell rate.(in cells per sec.) |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.25 | ColumnrpmChanRemoteMCR | read-only | mandatory | Minimum cell rate of the other end, if not set, will be set to the same as local end MCR. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.26 | ColumnrpmChanPercentUtil | read-only | mandatory | This is the expected long-term utilization of the channel by this end-point. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.27 | ColumnrpmChanRemotePercentUtil | read-only | mandatory | This is the expected long-term utilization of the channel by the other end-point. If this is not specified in the connection setup request, it'll be set to be … |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.28 | ColumnrpmChanEncapType | read-only | mandatory | ATM adaptation layer (AAL) and Encapsulation type. aal5snap - LLC/SNAP precedes the protocol datagram. aal34smds - Encapsulation for SMDS network. aal5nlpid - … |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.29 | ColumnrpmChanMidLow | read-only | mandatory | Starting Message Identifier Number for this PVC. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.30 | ColumnrpmChanMidHigh | read-only | mandatory | Ending Message Identifier Number for this PVC. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.31 | ColumnrpmChanBurstSize | read-only | mandatory | The Maximum number of ATM cells the virtual circuit can transmit. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.32 | ColumnrpmChanInArpFreq | read-only | mandatory | Specifies how often (in minutes) Inverse ARP datagrams will be sent on this virtual circuit. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.33 | ColumnrpmChanOAMloopback | read-only | mandatory | Specifies how often (in seconds) to generate an OAM F5 loopback cell from this virtual circuit. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.34 | ColumnrpmChanState | read-only | mandatory | This indicates the status of this channel. 1 ==> notConfigured 2 ==> active 3 ==> failed. Currently 'failed' state is not supported. When the channel is not ad… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.35 | ColumnrpmChanVirtualTemplate | read-only | mandatory | Specifies the Virtual Template used for CISCO PPP. If it is not using Virtual Template then this value is 0. |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.36 | ColumnrpmChanAbrRDF | read-only | mandatory | This is valid only for ABR Service Type. Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1 are received. Larger va… |
| 1.3.6.1.4.1.351.110.5.2.10.1.1.1.37 | ColumnrpmChanAbrRIF | read-only | mandatory | This is valid only for ABR Service Type. Rate Increase Factor: Controls the rate increase which occurs when a backward RM-cell is received with CI=0 and NI=0. … |
| 1.3.6.1.4.1.351.110.5.2.16 | NodepxmAtmMIBObjects | |||
| 1.3.6.1.4.1.351.110.5.2.16.10 | ScalarpxmAtmVcCrossConnectIndexNext | read-only | mandatory | This object contains an appropriate value to be used for pxmAtmVcCrossConnectIndex when creating entries in the pxmAtmVcCrossConnectTable. The value 0 indicate… |
| 1.3.6.1.4.1.351.110.5.2.16.11 | TablepxmAtmVcCrossConnectTable | not-accessible | mandatory | The ATM VC Cross Connect table. A bi- directional VC cross-connect which cross-connects two end points (i.e., VCLs) is modeled as one entry in this table. |
| 1.3.6.1.4.1.351.110.5.2.16.11.1 | RowpxmAtmVcCrossConnectEntry | not-accessible | mandatory | An entry in the ATM VC Cross Connect table. This entry is used to model a bi-directional ATM VC cross-connect cross-connecting two end points. Step-wise Proced… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.1 | ColumnpxmAtmVcCrossConnectIndex | read-only | mandatory | A unique value to identify this VC cross-connect. |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.2 | ColumnpxmAtmVcCrossConnectLowIfIndex | read-only | mandatory | The value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VC cross-connect. The term low implies that this ATM interface h… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.3 | ColumnpxmAtmVcCrossConnectLowVpi | read-only | mandatory | The value of this object is equal to the VPI value at the ATM interface associated with the VC cross-connect that is identified by pxmAtmVcCrossConnectLowIfInd… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.4 | ColumnpxmAtmVcCrossConnectLowVci | read-only | mandatory | The value of this object is equal to the VCI value at the ATM interface associated with this VC cross-connect that is identified by pxmAtmVcCrossConnectLowIfIn… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.5 | ColumnpxmAtmVcCrossConnectHighIfIndex | read-only | mandatory | The value of this object is equal to MIB II's ifIndex value for the ATM interface port for this VC cross-connect. The term high implies that this VC cross-conn… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.6 | ColumnpxmAtmVcCrossConnectHighVpi | read-only | mandatory | The value of this object is equal to the VPI value at the ATM interface associated with the VC cross-connect that is identified by pxmAtmVcCrossConnectHighIfIn… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.7 | ColumnpxmAtmVcCrossConnectHighVci | read-only | mandatory | The value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by pxmAtmVcCrossConnectHighIfIn… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.8 | ColumnpxmAtmVcCrossConnectAdminStatus | read-only | mandatory | The value of this object identifies the desired administrative status of this bi-directional VC cross-connect. The up and down states indicate that the traffic… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.9 | ColumnpxmAtmVcCrossConnectL2HOperStatus | read-only | mandatory | The value of this object identifies the current operational status of the VC cross-connect in one direction; (i.e., from the low to high direction). The up and… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.10 | ColumnpxmAtmVcCrossConnectH2LOperStatus | read-only | mandatory | The value of this object identifies the current operational status of the VC cross-connect in one direction; (i.e., from the high to low direction). The up and… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.11 | ColumnpxmAtmVcCrossConnectL2HLastChange | read-only | mandatory | The value of MIB II's sysUpTime object at the time this VC cross-connect entered its current operational state in low to high direction. If the current state w… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.12 | ColumnpxmAtmVcCrossConnectH2LLastChange | read-only | mandatory | The value of MIB II's sysUpTime object at the time this VC cross-connect entered its current operational state in high to low direction. If the current state w… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.13 | ColumnpxmAtmVcCrossConnectRowStatus | read-only | mandatory | The status of this entry in the pxmAtmVcCrossConnectTable. This object is used to create a new cross-connect for cross-connecting VCLs which are created using … |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.14 | ColumnpxmAtmVcCrossConnectHighAddressType | read-only | mandatory | The value of this object identifies the address type of the interface associated with the VC cross-connect that is identified by pxmAtmVcCrossConnectHighIfInde… |
| 1.3.6.1.4.1.351.110.5.2.16.11.1.15 | ColumnpxmAtmVcCrossConnectLowAddressType | read-only | mandatory | The value of this object identifies the address type of the interface associated with the VC cross-connect that is identified by pxmAtmVcCrossConnectLowIfIndex… |
| 1.3.6.1.4.1.351.110.5.3.1 | NodecesmPort | |||
| 1.3.6.1.4.1.351.110.5.3.1.1 | NodecesmPortCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.3.1.1.1 | TablecesmPortCnfGrpTable | not-accessible | mandatory | The config table is for logical port interface there are 192 entries for 8 DS1s or 248 entries for 8 E1s |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1 | RowcesmPortCnfGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.1 | ColumncesPortNum | read-only | mandatory | This is logical port number. If we have T1 card then the maximum port number is 192 and if we have E1 card the maximum port number can be 248 for T3 only one p… |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.2 | ColumncesPortRowStatus | read-write | mandatory | This variable enables or modifies the port 1- add 2 - del 3 - mod |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.3 | ColumncesPortLineNum | read-write | mandatory | This represents the line number to which this port is associated. For T3 only one line is supported. |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.4 | ColumncesPortType | read-write | mandatory | This represents port type whether it is carrying subrate circuits strau. If it is strau port then it can have only one DS0 time slot. In case of unstructured a… |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.5 | ColumncesPortDs0ConfigBitMap | read-write | mandatory | This respesents bit map of DS0s for a line which are used to form this logical port. Bit 0 represents DS0-1. |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.6 | ColumncesPortNumOfDs0Slot | read-write | mandatory | This represents number of DS0 time slots configured to this Port. If the port type is strau then this can not have more than 1 DS0 time slot. |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.7 | ColumncesPortNumOfSCIPerDS0 | read-write | mandatory | This is applicable only to the Strau Port. represents number of subcircuit in the DS0 time slot. 8 = there are 8 no .of 8kbps links (1 bit) 4 = there are 4 no … |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.8 | ColumncesPortSpeed | read-only | mandatory | Configured speed of port in kbps Max speed for T1 = 1544 Max speed for E1 = 2038 Max speed for T3 = 44736 Max spped for E3 = 34368 |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.9 | ColumncesPortState | read-only | mandatory | This variable indicates the state of the logical port |
| 1.3.6.1.4.1.351.110.5.3.1.1.1.1.10 | ColumncesPortBERTEnable | read-write | mandatory | This variable enables BERT This object is not supported in CESM-T3E3. |
| 1.3.6.1.4.1.351.110.5.3.1.1.2 | ScalarcesPortNextAvailable | read-only | mandatory | This variable contains the next UNUSED logical port number of the possible 32 DS0s * n ports. This number can be used in channel config table, the cesportNextA… |
| 1.3.6.1.4.1.351.110.5.3.1.1.3 | ScalarcesPortsUsedLine1 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.4 | ScalarcesPortsUsedLine2 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.5 | ScalarcesPortsUsedLine3 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.6 | ScalarcesPortsUsedLine4 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.7 | ScalarcesPortsUsedLine5 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.8 | ScalarcesPortsUsedLine6 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.9 | ScalarcesPortsUsedLine7 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.1.10 | ScalarcesPortsUsedLine8 | read-only | mandatory | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line… |
| 1.3.6.1.4.1.351.110.5.3.1.2 | NodecesmPortCnfResPartGrp | |||
| 1.3.6.1.4.1.351.110.5.3.1.2.1 | TablecesmPortCnfResPartGrpTable | not-accessible | mandatory | This table contains the configuration of port resource partition This is applicable for MGX8820(formerly AXIS) Rel. 5 and MGX. |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1 | RowcesmPortCnfResPartGrpEntry | not-accessible | mandatory | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.1 | ColumncesmResPartPortNum | read-only | mandatory | This is the logical port number, the index to this table. If we have T1 card then the maximum port number is 192 and if we have E1 card the maximum port number… |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.2 | ColumncesmResPartCtrlrNum | read-only | mandatory | This is index for controller using the port |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.3 | ColumncesmResPartRowStatus | read-write | mandatory | This will add, delete or modify the partition. 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.4 | ColumncesmResPartNumOfLcnAvail | read-write | mandatory | This represents number of LCNs available for this controller and this port. In CESM-T3/E3 and 8-T1/E1,this value is 1. |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.5 | ColumncesmResPartLcnLow | read-write | mandatory | This represents low end of reserved LCN In CESM-8T1/E1 and T3/E3, this refers to the logical port. |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.6 | ColumncesmResPartLcnHigh | read-write | mandatory | This represents high end of reserved LCN In CESM-8T1/E1 and T3/E3, this refers to the logical port. |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.7 | ColumncesmResPartIngrPctBW | read-write | mandatory | The percentage of total ingress bandwidth reserved. In CESM-8T1/E1 and T3/E3, as there is only one LCN per port and it could be used by only one controller,thi… |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.8 | ColumncesmResPartEgrPctBW | read-write | mandatory | The percentage of total egress bandwidth reserved In CESM-8T1/E1 and T3/E3, as there is only one LCN per port and it could be used by only one controller,this … |
| 1.3.6.1.4.1.351.110.5.3.1.2.1.1.9 | ColumncesmResPartCtrlrID | read-write | mandatory | This is the controller identifier for the resource patition. The default value is set for PNNI controller. |
| 1.3.6.1.4.1.351.110.5.3.2.1 | NodecesmChanCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.3.2.1.1 | TablecesmChanCnfGrpTable | not-accessible | mandatory | The config table is for logical channel interface there are 4 entries for 4 DS1s in case of CESM-4P in case of CESM-8P it can have 263 entries. For CESM-T3/E3 … |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1 | RowcesmChanCnfGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.1 | ColumncesCnfChanNum | read-only | mandatory | Refers to the virtual connection no. In case of CESM-4P the range is 16..19 (only for 4 entries). for CESM-8t1 we can have 192 and for CESM-8e1 we can have 248… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.2 | ColumncesChanRowStatus | read-write | mandatory | This indicates the channel status 1 ==> ADD 2 ==> DELETE 3 ==> MODIFY 4 ==> Setting this object to outOfService takes the channel out of service or brings the … |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.3 | ColumncesMapPortNum | read-only | mandatory | In case of CESM-4P this variable specifies the port number to which this channel is associated. Mappings are as - Port 1 - channel 16, 2-17, 3-18, 4-19 (it can… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.4 | ColumncesMapVpi | read-only | mandatory | The value of this object is equal to the VPI used for the emulated circuit represented by this connection. In MGX8220( formerly AXIS) Implementaion slot number… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.5 | ColumncesMapVci | read-only | mandatory | This specifies VCI for emulated circuit represented by this VC. Our Implementation cesCnfChanNum will be used for this. In case of CESM-4P valid range is 16..1… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.6 | ColumncesCBRService | read-only | mandatory | This specifies data type supported by the CBR service Only Unstructured mode is supported in CESM-4P CESM-8P supports both structured and unstructured mode for… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.7 | ColumncesCBRClockMode | read-write | mandatory | This specifies clocking mode of the CBR service Only synchronous mode is supported in CESM-4P Structured mode is always synchronous. CESM -T3 will support only… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.8 | ColumncesCas | read-write | mandatory | Specifies if CAS bits are carried by the service. This also selects which AAL1 format should be used. Only basic mode is supported for unstructured connections… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.9 | ColumncesPartialFill | read-write | mandatory | Specifies the number of user octets per cell, if partial cell fill is used. 47 means partial fill disabled. Partial fill is not supported in CESM-4P Ranges for… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.10 | ColumncesBufMaxSize | read-write | mandatory | Specifies the maximum size in octets of egress buffer. CESM - 4P: Should be at least 0.6*CDVRxT for a T1 line and 0.7 * CDVRxT for a E1 line. 0 can be specifie… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.11 | ColumncesCDVRxT | read-write | mandatory | Specifies maximum cell arrival jitter that the reassembly process will tolerate. In case of CESM-8P it should be in increment of 125 micro secs and Max limit a… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.12 | ColumncesCellLossIntegrationPeriod | read-write | mandatory | Specifies the cell loss integration period in milliseconds |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.13 | ColumncesChanLocRmtLpbkState | read-write | mandatory | Loopback on cellbus in egress direction. |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.14 | ColumncesChanTestType | read-write | mandatory | This is the type of the test 1 = Test Continuity 2 = Test Delay 3 = no test is initated 4 = test continuity with sti cell format 5 = test delay with sti cell f… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.15 | ColumncesChanTestState | read-only | mandatory | This shows the state of the test 1 = Passed 2 = Failed 3 = In Progress 4 = Not In Progress |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.16 | ColumncesChanRTDResult | read-only | mandatory | This is round trip delay in milliseconds |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.17 | ColumncesChanPortNum | read-write | mandatory | This indicates to which logical port this connection belongs. Applicable on CESM-8T1/E1 or CESM-T3/E3. 1.. 248 for E1 1.. 192 for T1 1.. 1 for T3 Only applicab… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.18 | ColumncesChanConnType | read-write | mandatory | This indicates the type of connection. 1 = PVC 2 = SVC 3 ==> SPVC connection Only applicable to CESM-8P and CESM-T3/E3. |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.19 | ColumncesChanStrauSciNum | read-write | mandatory | This indicates the type of connection. 1 = Normal Channel (nonStrauChannel(0) ) 2 = SCI 1 i.e bit 1 & 2 3 = SCI 2 i.e bit 3 & 4 4 = SCI 3 i.e bit 5 & 6 5 = SCI… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.20 | ColumncesChanIdleDetEnable | read-write | mandatory | This indicates the type of Idle detection enabled 1 = Idle code detection is disabled. 2 = This will enable Idle detection whenver it detects Onhook in ABCD bi… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.21 | ColumncesChanIdleSignalCode | read-write | mandatory | When cesChanIdleDetEnable = enableIdlePatternDet 3. This object will carry value 0..0xff and this will indicate Idle pattern in DS0 time slots. Only applicable… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.22 | ColumncesChanIdleCodeIntgnPeriod | read-write | mandatory | This variable indicates the Integration period in seconds whenever cesChanIdleDetEnable = enableIdlePatternDet Only applicable to CESM-8P and not supported in … |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.23 | ColumncesChanOnhookCode | read-write | mandatory | When cesChanIdleDetEnable = enableOnhookDet 1. This will carry value 0..3 for framing mode SF. 2. This will carry value 0..15 for framing mode ESF/e1Cas. Only … |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.24 | ColumncesChanConditionedData | read-write | mandatory | This byte will indicate Idle data to be sent towards the line whenever channels goes in to Underrun Only applicable for CESM-8T1/E1 |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.25 | ColumncesmChanExtTrgIdleSupp | read-write | mandatory | Using this variable we can initiate Idle suppression on the connection. This can be set by external signalling device. Only applicable to CESM-8T1/E1. |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.26 | ColumncesmChanConditionedSigCode | read-write | mandatory | This byte will indicate Signal code to be sent sent towards the line whenever channels goes in to Underrun Only applicable to CESM-8T1/E1 |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.27 | ColumncesLocalVpi | read-only | mandatory | This VPI together with the local VCI and NSAP represents the local end point in this connection, this object is read only, therefore it'll be assigned by SM to… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.28 | ColumncesLocalVci | read-only | mandatory | This VCI together with the local VPI and NSAP represents the local end point in this connection, this object is read only, therefore it'll be assigned by SM to… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.29 | ColumncesLocalNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 1 byte rsvd, 3 bytes for logical interface: slot (1 byte) and por… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.30 | ColumncesRemoteVpi | read-write | mandatory | This VPI together with the remote VCI and NSAP represents the remote end point in this connection. The value should be 0 for a DACS connection in MGX |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.31 | ColumncesRemoteVci | read-write | mandatory | This VCI together with the remote VPI and NSAP represents the remote end point in this connection. The value should be 0 for a DACS connection in MGX |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.32 | ColumncesRemoteNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 1 byte rsvd, 3 bytes for logical interface: slot (1 byte) and por… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.33 | ColumncesMastership | read-write | mandatory | This is used by PXM to determine if this end point is master or slave, a new type unknown is added to identify the SM in MGX8220(formerly AXIS) shelf and the S… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.34 | ColumncesVpcFlag | read-write | mandatory | This represents the connection type, used for PXM to identify VPC/VCC but CESM card doesn't use it always set to vcc for CESM card |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.35 | ColumncesConnServiceType | read-write | mandatory | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard … |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.36 | ColumncesRoutingPriority | read-write | mandatory | This is used by PXM to determine how important this connection is when selecting connections to route |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.37 | ColumncesMaxCost | read-write | mandatory | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. T… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.38 | ColumncesRestrictTrunkType | read-write | mandatory | Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.39 | ColumncesConnPCR | read-write | mandatory | Peak cell rate,if not provided in the connection setup request,it will be computed as follows, For CESM-8T1/E1 - N * 64 Kbps , where N = Number of timeslots as… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.40 | ColumncesConnMCR | read-write | mandatory | Minimum cell rate,if not provided in the connection setup request,it will be computed as follows, For CESM-8T1/E1 - N * 64 Kbps , where N = Number of timeslots… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.41 | ColumncesConnPercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by theis end-point. For CESM-8T1/E1/T3/E3 , the value is 100% |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.42 | ColumncesmConnRemotePCR | read-write | mandatory | Peak cell rate of the other end, if not set in MGX, will be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.43 | ColumncesmConnRemoteMCR | read-write | mandatory | Minimum cell rate of the other end, if not set in MGX, will be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.44 | ColumncesmConnRemotePercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by the other end-point. |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.45 | ColumncesmConnForeSightEnable | read-write | mandatory | This object is used by the controller(PAR/PNNI/TAG) to set up the Qbin for the connection. This is notapplicable to CESM-8T1/E1/T3/E3. |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.46 | ColumncesmConnFGCRAEnable | read-write | mandatory | enables/disables Frame based GCRA (early packet discard). This is not applicable to CESM-8T1/E1/T3/E3. |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.47 | ColumncesmChanReroute | read-write | mandatory | This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to fals… |
| 1.3.6.1.4.1.351.110.5.3.2.1.1.1.48 | ColumncesmConnAdminStatus | read-write | mandatory | This object specifies channel admin status. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.3.2.1.2 | ScalarcesmChanNumNextAvailable | read-only | mandatory | This variable contains the next unused channel number of the possible 248. This number can be used in channel config table. cesChanNumNextAvailable gets update… |
| 1.3.6.1.4.1.351.110.5.3.2.2 | NodecesmChanCntGrp | |||
| 1.3.6.1.4.1.351.110.5.3.2.2.1 | TablecesmChanCntGrpTable | not-accessible | mandatory | The config table is for logical channel interface there are 4 entries for 4 DS1s in case of CESM-4P In case of CESM-8P it can have 352 entries. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1 | RowcesmChanCntGrpEntry | not-accessible | mandatory | An entry for logical channel |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.1 | ColumncesCntChanNum | read-only | mandatory | Refers to the channel Number 16 - 19 for CESM-4P 32 - 279 for CESM-8t1e1 32 for CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.2 | ColumncesChanState | read-only | mandatory | This variable indicates the connection status failed(4) is added to distinguish between alarm (when the connection segment is not actually broken) and failed(w… |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.3 | ColumncesXmtATMState | read-only | mandatory | This variable indicates the transmit state of channel on the ATM side (towards the network). |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.4 | ColumncesRcvATMState | read-only | mandatory | This variable indicates the receive state of channel on the ATM side (from the network). |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.5 | ColumncesCellLossStatus | read-only | mandatory | When cells are lost for the CellLossIntegrationPeriod the value is set to loss ( 2). when cells are no longer lost, the value is set to noLoss(1). |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.6 | ColumncesReassCells | read-only | mandatory | The number of cells played out to T1/E1/T3E3 interface. It excludes cells that were discarded for any reason. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.7 | ColumncesGenCells | read-only | mandatory | The number of cells generated from T1/E1/T3E3 interface and sent towards network. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.8 | ColumncesHdrErrors | read-only | mandatory | The number of AAL-1 header errors detected and possibly corrected. Header errors include correctable and uncor- rectable CRC, plus bad parity. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.9 | ColumncesPointerReframes | read-only | mandatory | The number of events in which the AAL1 reassembler found that an SDT pointer is not where it is expected and the and the pointer must be reacquired. Not suppor… |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.10 | ColumncesLostCells | read-only | mandatory | The number of cells lost in egress direction due to AAL 1 header errors and missing cells. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.11 | ColumncesBufUnderflows | read-only | mandatory | The number of buffer underflows in Egress direction Not supported in cesm8P due limitation in AAL1 SAR. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.12 | ColumncesBufOverflows | read-only | mandatory | The number of buffer overflows in Egress direction Not supported in cesm8P due limitation in AAL1 SAR. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.13 | ColumncesIngrDiscardedBytes | read-only | mandatory | The number of bytes discarded due to shelf alarm in ingress direction from port data. Not supported in CESM-8P. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.14 | ColumncesUflowInsCells | read-only | mandatory | The Number of All 1's cells inserted in case of Egress Buffer Underflow Not supported in CESM-8P. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.15 | ColumncesOflowDropBytes | read-only | mandatory | The Number of bytes discarded in Egress direction because of Egress buffer overflow Not supported in CESM-8P. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.16 | ColumncesCellSeqMismatchCnt | read-only | mandatory | The Number of times SAR received a valid out of sequence AAL-1 cell from CellBus. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.17 | ColumncounterClrButton | read-write | mandatory | writing a value of 2 resets all the counters |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.18 | ColumncesChanSecUptime | read-only | mandatory | The Number of seconds channel is in service only applicable for CESM-8P |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.19 | ColumncesChanSignalingStatus | read-only | mandatory | This variable indicates the connection signalling status Connection will be in Idle suppression mode if it in on-hook. Not applicable for T3E3 and CESM-4P. |
| 1.3.6.1.4.1.351.110.5.3.2.2.1.1.20 | ColumncesChanStatusBitMap | read-only | mandatory | This variable indicates the consolidated bit map of the channel alarm state. Individual bit positions are as defined below. Bit position Fail/Alarm Reason 0 Al… |
| 1.3.6.1.4.1.351.110.5.3.3 | NodecesmEndPtMapGrp | |||
| 1.3.6.1.4.1.351.110.5.3.3.1 | TablecesmEndPtMapGrpTable | not-accessible | mandatory | There are 248 entries and port num will uniquely identify a row. For CESM-8T1/E1 , only 248 ports are possible. For CESM-T3/E3, only one port is possible. |
| 1.3.6.1.4.1.351.110.5.3.3.1.1 | RowcesmEndPtMapGrpEntry | not-accessible | mandatory | An entry for cesmEndPtMapGrpEntry. |
| 1.3.6.1.4.1.351.110.5.3.3.1.1.1 | ColumncesEndPortNum | read-only | mandatory | Refers to the logical port index CESM-8E1 supports 248 ports. CESM-8T1 supports 192 ports. CESM-T3/E3 supports only one port. |
| 1.3.6.1.4.1.351.110.5.3.3.1.1.2 | ColumncesEndChanNum | read-only | mandatory | Logical connection number for above cesEndPortNum |
| 1.3.6.1.4.1.351.110.5.3.3.1.1.3 | ColumncesEndLineNum | read-only | mandatory | Refers to the physical line index In case T3 only one line will be supported. |
| 1.3.6.1.4.1.351.110.5.5.2.1 | NodevismPortCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.5.2.1.1 | TablevismPortCnfGrpTable | not-accessible | mandatory | Port configuration table for the virtual port. Only one entry is allowed in this table. |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1 | RowvismPortCnfGrpEntry | not-accessible | mandatory | An entry for logical port. |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.1 | ColumnvismPortNum | read-only | mandatory | This is a logical port number. If PXM1 is the PXM used on the shelf this object should be set to 1. For PXM1E this object should be set to 255. . |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.2 | ColumnvismPortRowStatus | read-write | mandatory | To add, del or modify a port. To add the port, this object has to be set to add, values for other objects should not be specififed (refer to Note 1). VISM will… |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.3 | ColumnvismPortLineNum | read-write | mandatory | This represents the line number to which this port is associated. Since the network port is not associated with any line, line number 0 is returned on a GET. T… |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.4 | ColumnvismPortType | read-write | mandatory | The value of this object is always set to voIP. It indicates that it is the network port. The same value is used even when VISM supports VoAAL1 or VoAAL2. The … |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.5 | ColumnvismPortDs0ConfigBitMap | read-write | mandatory | This respesents the bit map of DS0s which is used to create this port. Bit 0 represents DS0-1. Since this object is not applicable to the network port, value 0… |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.6 | ColumnvismPortSpeed | read-write | mandatory | The speed of the port in cells per second. It is used by VISM card to advertise virtual port bandwidth to the controller, SVC and PVC connection admission cont… |
| 1.3.6.1.4.1.351.110.5.5.2.1.1.1.7 | ColumnvismPortState | read-only | mandatory | This object indicates the state of the port. |
| 1.3.6.1.4.1.351.110.5.5.2.2 | NodevismPortResPartCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.5.2.2.1 | TablevismPortResPartCnfGrpTable | not-accessible | mandatory | This table contains the configuration of port resource partition. Currently this table contains a single row. |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1 | RowvismPortResPartCnfGrpEntry | not-accessible | mandatory | An entry for port resource partition. |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.1 | ColumnvismResPartPortNum | read-only | mandatory | This is the logical port number, the index to this table. If PXM1 is the PXM used on the shelf this object should be set to 1. For PXM1E this object should be … |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.2 | ColumnvismResPartCtrlrNum | read-only | mandatory | This is index for controller using the port. In MGX release 1.0, the value par should be used. In MGX release 2.0, the value pnni should be used. |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.3 | ColumnvismResPartRowStatus | read-write | mandatory | This will add, delete or modify the partition. In MGX Release1.0: To add an entry, this object should be set to add, value for other objects should not be spec… |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.4 | ColumnvismResPartNumOfLcnAvail | read-write | mandatory | This represents number of LCNs available for this controller and this port. The default value for this object is chosen based on vismMode : default value in vo… |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.5 | ColumnvismResPartLcnLow | read-write | mandatory | This represents low end of reserved LCN. Currently SET is not allowed on this object. |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.6 | ColumnvismResPartLcnHigh | read-write | mandatory | This represents high end of reserved LCN. Currently SET is not allowed on this object. |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.7 | ColumnvismResPartIngrPctBW | read-write | mandatory | The percentage of total ingress bandwidth reserved. Since we have only one LCN for VoIP, the value is 100. Currently SET is not allowed on this object. From vi… |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.8 | ColumnvismResPartEgrPctBW | read-write | mandatory | The percentage of total egress bandwidth reserved Since we have only one LCN for VoIP, the value is 100. Currently SET is not allowed on this object. From vism… |
| 1.3.6.1.4.1.351.110.5.5.2.2.1.1.9 | ColumnvismResPartCtrlrID | read-write | mandatory | This is the controller identifier of the PNNI controller. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1 | TablevismChanCnfGrpTable | not-accessible | mandatory | The channel config table for voice traffic. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1 | RowvismChanCnfGrpEntry | not-accessible | mandatory | An entry for each voice channel. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.1 | ColumnvismCnfChanNum | read-only | mandatory | Logical Channel Number for the PVC. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.2 | ColumnvismChanRowStatus | read-write | mandatory | An entry is created by setting this object to add. Once the entry is added, the value mod is returned for successive GETs. The value mod is used to modify an e… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.3 | ColumnvismChanPortNum | read-write | mandatory | This refers to the virtual port between VISM and PXM. This number is defaulted to the appropriate number for the shelf. (1 for PXM1 and 255 for PXM1E) |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.4 | ColumnvismChanLocRmtLpbkState | read-write | mandatory | Loopback on cellbus in egress direction. This variable enables or disables the remote loopback for each channel. When you enable this option on a connection (c… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.5 | ColumnvismChanTestType | read-write | mandatory | This is the type of the test. 1 = Test Continuity 2 = Test Delay 3 = No test notest is meant for GET only. While doing a SET on this object, the SET request sh… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.6 | ColumnvismChanTestState | read-only | mandatory | This shows the state of the test. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.7 | ColumnvismChanRTDResult | read-only | mandatory | This is round trip delay in milliseconds. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.8 | ColumnvismChanPvcType | read-write | mandatory | PVC type. In VISM 1.0 pvc type VoIP was supported. It has been deprecated in the current release. This is a mandatory parameter when adding a PVC. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.9 | ColumnvismChanConnType | read-write | mandatory | Connection type. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.10 | ColumnvismLocalVpi | read-only | mandatory | This VPI together with the local VCI and NSAP represents the local end point in this connection. GET on this object returns value=0. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.11 | ColumnvismLocalVci | read-only | mandatory | This VCI together with the local VPI and NSAP represents the local end point in this connection. GET on this object returns the vismCnfChanNum or LCN. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.12 | ColumnvismLocalNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix(node name), 2 bytes for Cisco ID, 1 byte rsvd, 3 bytes for logical interface: slot (1 by… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.13 | ColumnvismRemoteVpi | read-write | mandatory | This VPI together with the remote VCI and NSAP represents the remote end point in this connection. This parameter is required only if vismMastership is set to … |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.14 | ColumnvismRemoteVci | read-write | mandatory | This VCI together with the remote VPI and NSAP represents the remote end point in this connection. This parameter is required only if vismMastership is set to … |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.15 | ColumnvismRemoteNSAP | read-write | mandatory | This NSAP is 20 bytes binary, among these 20 bytes: 13 bytes as prefix, 2 bytes for Cisco ID, 1 byte rsvd, 3 bytes for logical interface: slot (1 byte) and por… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.16 | ColumnvismMastership | read-write | mandatory | This is used by PXM to determine if this end point is master or slave. For VoIP channel, the value is master (1). |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.17 | ColumnvismVpcFlag | read-write | mandatory | This is used by PXM to identify the connection type. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.18 | ColumnvismConnServiceType | read-write | mandatory | This specifies the class of service or service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 1 (Real Time) Although, VISM does not do any kind of traffi… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.19 | ColumnvismRoutingPriority | read-write | mandatory | This is used by PXM to determine how important this connection is when selecting connections to route. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.20 | ColumnvismMaxCost | read-write | mandatory | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. T… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.21 | ColumnvismRestrictTrunkType | read-write | mandatory | Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.22 | ColumnvismConnPCR | read-write | mandatory | This indicates bandwidth(Peak Cell Rate) in cells per second from the local end i.e in the ingress direction of the PVC. For a VoIP bearer PVC, the max value i… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.23 | ColumnvismConnPercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by this end-point. Currently only 100 is allowed. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.24 | ColumnvismConnRemotePCR | read-write | mandatory | This indicates bandwidth(Peak Cell Rate) from the other end i.e in the egress direction of the PVC. This value is expressed in units of cells per second. If no… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.25 | ColumnvismConnRemotePercentUtil | read-write | mandatory | This is the expected long-term utilization of the channel by the other end-point. Currently only 100 is allowed. |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.26 | ColumnvismChanProtection | read-write | mandatory | This object is used to configure a PVC protection group (or redundant group) with the PVCs protecting each other. Currently only two PVCs are supported in a pr… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.27 | ColumnvismChanPreference | read-write | mandatory | This object is used to identify a PVC as primary or secondary. The primary PVC should be added before the secondary. Similarly secondary should be deleted befo… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.28 | ColumnvismChanActivityState | read-only | mandatory | Indicates whether the PVC is currently used to carry IP traffic or not, and whether it has failed. The possible states are: active - Channel is healthy and is … |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.29 | ColumnvismChanLockingState | read-write | mandatory | This object is used to control the switchover of protected channels. The possible values are: unlock - Transition state to unlock. A channel which is in lock s… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.30 | ColumnvismChanScrIngress | read-write | mandatory | This object defines the SCR (Sustained Cell Rate) for the PVC. SCR is used for vbr connection types only. Although, based on the value of SCR, any kind of traf… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.31 | ColumnvismChanMbsIngress | read-write | mandatory | This object defines the MBS (Max. Burst Size) in cells per second. This object is meaningful for VBR connections only. This object defines the MBS value for th… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.32 | ColumnvismChanClrIngress | read-write | mandatory | This object defines the CLR (Cell Loss Ratio) for the PVC. This field is also meaningful for VBR connections only. This object defines the CLR value for the in… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.33 | ColumnvismChanCdvt | read-write | mandatory | This object defines the CDVT (Cell Delay Variation Tolerance) for the connection. CDVT is useful for detemining the playout buffer size in the DSPs. This objec… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.34 | ColumnvismConnPCREgress | read-write | mandatory | This object defines the PCR (Peak Cell Rate) for the PVC. PCR is applicable to all connection service types ie. CBR, RT-VBR and nRT-VBR. This value is expresse… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.35 | ColumnvismChanScrEgress | read-write | mandatory | This object defines the SCR (Sustained Cell Rate) for the PVC. SCR is used for vbr connection types only. Although, based on the value of SCR, any kind of traf… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.36 | ColumnvismChanMbsEgress | read-write | mandatory | This object defines the MBS (Max. Burst Size) in cells per second. This object is meaningful for VBR connections only. This object defines the MBS value for th… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.37 | ColumnvismChanClrEgress | read-write | mandatory | This object defines the CLR (Cell Loss Ratio) for the PVC. This field is also meaningful for VBR connections only. This object defines the MBS value for the eg… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.38 | ColumnvismChanApplication | read-write | mandatory | This object defines the application that the LCN is used for. There are 4 types of PVCs known so far: 1 - Control PVC used for carrying control traffic only (S… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.39 | ColumnvismChanFallbackLcn | read-write | mandatory | This object defines the LCN to be used as a fallback mechanism, in case the primary PVC fails. This is applicable if the PVC is configured for redundancy. The … |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.40 | ColumnvismChanReroute | read-write | mandatory | This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to fals… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.41 | ColumnvismFarEndAddressType | read-write | mandatory | The address type can be one of five types: NSAP, E164, GWID, notapplicable or unspecified. It determines which object contains the scope for the VCCI, i.e. whe… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.42 | ColumnvismFarEndE164Address | read-write | mandatory | The E.164 address of the far end peer. The address is expressed as decimal numbers with up to 15 digits. If the vismFarEndAddressType is different from e164, t… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.43 | ColumnvismFarEndGWIDAddress | read-write | mandatory | The gateway ID of the far end peer. The address is expressed as ASCII characters. If the vismFarEndAddressType is different from gwid, this object is not appli… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.44 | ColumnvismFarEndNSAPAddress | read-write | mandatory | This object contains the 20 byte NSAP address of the far end peer. If the vismFarEndAddressType is different from nsap, this object is not applicable and it sh… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.45 | ColumnvismVCCI | read-write | mandatory | The VCCI, or Virtual Circuit Connection Identifier, is a variable that identifies a virtual circuit connection between two nodes. A virtual circuit connection,… |
| 1.3.6.1.4.1.351.110.5.5.3.1.1.1.46 | ColumnvismConnAdminStatus | read-write | mandatory | This object specifies channel administration status. |
| 1.3.6.1.4.1.351.110.5.5.3.1.2 | ScalarvismChanNumNextAvailable | read-only | mandatory | This variable contains the next unused channel number. When channels are available the range is 32..510. This number can be used in channel config table. Value… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3 | TablevismChanCacTable | not-accessible | mandatory | This table defines the CAC success or failure statistics. CAC functionality is applied on a per PVC basis for accepting the new calls in a switching model (i.e… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1 | RowvismChanCacEntry | not-accessible | mandatory | This table is used for CAC functions on a PVC. Each entry in this table corresponds to a PVC, since the CAC functionality is applied on a per PVC basis. The ba… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.1 | ColumnvismChanNum | read-only | mandatory | This attribute defines the index for the vismChanCac Table. The LCN Number is the same as the LCN value used as the index for the vismChanCnfGrpTable i.e. vism… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.2 | ColumnvismChanCacMaster | read-write | mandatory | This attribute defines whether the PVC is the master end or slave end. CAC functionality is applied only at the master end of the PVC. It is not necessary if t… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.3 | ColumnvismChanCacPassedCons | read-only | mandatory | This attribute defines the count of connections that passed successfully the CAC function. CAC functionality is applied either due to 1) The CRCX message sent … |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.4 | ColumnvismChanCacRejectedCons | read-only | mandatory | This attribute defines the count of connections that got rejected due to CAC function. The CAC rejection was due to the bandwidth not being available on a give… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.5 | ColumnvismChanCacRejectionPolicy | read-write | mandatory | This attribute defines the policy that needs to be applied once the CAC function rejects the upspeeding of a connection, due to a fax/modem switch-over request… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.6 | ColumnvismChanCarrierLossPolicy | read-write | mandatory | This object defines the policy that needs to be applied when a carrier loss is detected. This states whether to switch to the pre-upspeed codec or to remain wi… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.7 | ColumnvismChanVADTolerance | read-write | mandatory | The value in this object refers to the customer accepted drop rate for voice connections when the bandwidth usage exceeds allowed value. The actual range of th… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.8 | ColumnvismChanVADDutyCycle | read-write | mandatory | This object refers to the talk-spurts duty cycle. The unit is in percentage. The actual range of this object is 0.01 to 0.99 % and not 0.01 to 1.00 % as specif… |
| 1.3.6.1.4.1.351.110.5.5.3.1.3.1.9 | ColumnnetworkCacConfigState | read-only | mandatory | This attribute defines whether the originating and terminating VISMs are configured properly or not, by default the configuration is assumed to be ok and this … |
| 1.3.6.1.4.1.351.110.5.5.3.2 | NodevismChanStateGrp | |||
| 1.3.6.1.4.1.351.110.5.5.3.2.1 | TablevismChanStateGrpTable | not-accessible | mandatory | voice connection state table |
| 1.3.6.1.4.1.351.110.5.5.3.2.1.1 | RowvismChanStateGrpEntry | not-accessible | mandatory | An entry for each channel (PVC) |
| 1.3.6.1.4.1.351.110.5.5.3.2.1.1.1 | ColumnvismStateChanNum | read-only | mandatory | Refers to the channel Number LCN. |
| 1.3.6.1.4.1.351.110.5.5.3.2.1.1.2 | ColumnvismChanState | read-only | mandatory | Channel status. |
| 1.3.6.1.4.1.351.110.5.5.3.2.1.1.3 | ColumnvismChanXmtATMState | read-only | mandatory | This variable indicates the transmit state of channel on the ATM side(towards the network). |
| 1.3.6.1.4.1.351.110.5.5.3.2.1.1.4 | ColumnvismChanRcvATMState | read-only | mandatory | This variable indicates the receive state of channel on the ATM side(from the network). |
| 1.3.6.1.4.1.351.110.5.5.3.2.1.1.5 | ColumnvismChanStatusBitMap | read-only | mandatory | This variable indicates the consolidated bit map of the channel alarm state. Individual bit positions are as defined below, all reserved bits will be set to ze… |
| 1.3.6.1.4.1.351.110.5.5.3.3 | NodevismChanCntGrp | |||
| 1.3.6.1.4.1.351.110.5.5.3.3.1 | TablevismChanCntGrpTable | not-accessible | mandatory | vism channel counters table. This table gets implicitly created and deleted at the time of creation and deletion of ChanCnfGrp. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1 | RowvismChanCntGrpEntry | not-accessible | mandatory | An entry for each voice channel. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.1 | ColumnvismCntChanNum | read-only | mandatory | Refers to the logical channel Number. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.10 | ColumnvismCntClrButton | read-only | mandatory | writing a value of 2 resets all the counters. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.11 | ColumnvismChanAal2HecErrors | read-only | mandatory | The count of egress AAL2 CPS(Common Part Sub-layer) PDUs dropped due to HEC (Header Error Control) error. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.12 | ColumnvismChanAal2CrcErrors | read-only | mandatory | The count of egress AAL2 type3 CPS PDUs dropped due to invalid CRC-10 error. CRC validation is for type 3 packets only. Type 1 packets are not subjected to CRC… |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.13 | ColumnvismChanAal2OamLpbLostCells | read-only | mandatory | The count of OAM loopback cells lost. OAM loopback cells are sent on a periodic basis (1sec) on each PVC to monitor the health of the PVC. This is applicable f… |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.14 | ColumnvismChanAal2InvOsfCells | read-only | mandatory | The Number of AAL2 cells dropped due to invalid OSF (OffSet Field) in the egress direction. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.15 | ColumnvismChanAal2InvParCells | read-only | mandatory | The Number of AAL2 cells dropped due to invalid Parity bit field in the egress direction. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.16 | ColumnvismChanAal2CpsSentPkts | read-only | mandatory | The count of AAL2 CPS packets sent to the network. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.17 | ColumnvismChanAal2CpsRcvdPkts | read-only | mandatory | The count of AAL2 CPS packets received from the network. This does not include the packets which are counted as error packets. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.18 | ColumnvismChanAal2CpsInvCidPkts | read-only | mandatory | The count of AAL2 CPS packets dropped in the egress direction due to invalid CID (Channel ID). The CID may be considered as invalid if - a) It is out of range.… |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.19 | ColumnvismChanAal2CpsInvUuiPkts | read-only | mandatory | The count of AAL2 CPS packets dropped in the egress direction due to invalid UUI (User-to-User Info.) field. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.20 | ColumnvismChanAal2CpsInvLenPkts | read-only | mandatory | The count of AAL2 CPS packets dropped in the egress direction due to invalid length field. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.21 | ColumnvismChanAal5InvCpiPdus | read-only | mandatory | The count of AAL5 PDUs dropped in the egress direction due to invalid CPI (common part indicator) field in the AAL5 PDU trailer. This is applicable only to the… |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.22 | ColumnvismChanAal5OversizedSdusRcvdPdus | read-only | mandatory | The count of AAL5 PDUs dropped due to the SDU size bigger than the configured value. This is applicable for AAL5 PVCs only. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.23 | ColumnvismChanAal5InvLenPdus | read-only | mandatory | The count of AAL5 PDUs dropped due to the length violations. This is applicable to the CCS PVCs. The HDLC frames should have a minimum frame size in order for … |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.24 | ColumnvismChanAal5Crc32ErrorPdus | read-only | mandatory | The count of AAL5 PDUs dropped in the egress direction due to CRC-32 errors detected by the SAR. |
| 1.3.6.1.4.1.351.110.5.5.3.3.1.1.25 | ColumnvismChanAal5ReassemTimerExpiryPdus | read-only | mandatory | The count of AAL5 PDU reassembly timer expirations. The timers are maintained in the egress direction for building an AAL5 PDU from the cells. |
| 1.3.6.1.4.1.351.110.5.5.3.4 | NodevismAal2CidGrp | |||
| 1.3.6.1.4.1.351.110.5.5.3.4.1 | TablevismAal2CidCnfTable | not-accessible | mandatory | This table is defined to establish the binding between an endpoint and a PVC/CID pair in the case of AAL2 adaptation. This table is created and used in trunkin… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1 | RowvismAal2CidEntry | not-accessible | mandatory | Please see the above description. |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.1 | ColumnvismAal2CidNum | read-only | mandatory | This attribute defines part of the index for the cid Table. vismAal2CidNum is the CID (or Channel ID) of a voice channel. CID has to be the same at both endpoi… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.2 | ColumnvismAal2CidLcn | read-only | mandatory | This attribute defines part of the index for the cid Table. Since CID is unique to a PVC, a combination of LCN and CID uniquely identifies a voice connection. … |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.3 | ColumnvismAal2EndptNum | read-write | mandatory | This attribute defines the endpoint number to which this CId is associated. It is the same as mgEndpointNumber in in mgEndpointTable |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.4 | ColumnvismAal2CidRowStatus | read-write | mandatory | This variable allows to add or delete a CID. A CID can only be added or deleted. Once added, mdifying an entry is not allowed. createAndGo: Use this to add an … |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.5 | ColumnvismAal2CidType3Redundancy | read-write | mandatory | This attribute defines whether the triple redundancy is supported for type 3 packets in AAL2 for this channel. When Triple redundancy is enabled for a channel,… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.6 | ColumnvismAal2CidVad | read-write | mandatory | This attribute defines whether the VAD (Voice Activity Detection) has to be applied on this channel, upon detection of silence. For algorithms that do not have… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.7 | ColumnvismAal2CidProfileType | read-write | mandatory | This attribute defines the profile type. The profile type defines which group of the profile tables the profile number should correspond to. There are three po… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.8 | ColumnvismAal2CidProfileNum | read-write | mandatory | This attribute defines the profile number. A profile is a set of entries, where each entry specifies an encoding format with a UUI range and length. This set d… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.9 | ColumnvismAal2CidCodecType | read-write | mandatory | This attribute defines the codec Type used for the connection. g711u represents PCMU with 64 kbps. g711a represents PCMA with 64 kbps. g726r32000 represents G.… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.10 | ColumnvismAal2CidDtmfTransport | read-write | mandatory | This attribute defines whether the DTMF (Dual Tone Multi Frequency) digits need to be transported to the other end-point. |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.11 | ColumnvismAal2CidCasTransport | read-write | mandatory | This attribute defines whether the CAS (ABCD bits) bits need to be transported to the other endpoint. In the case of switching application, the CAS bits are ba… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.12 | ColumnvismAal2CidEcanEnable | read-write | mandatory | This attribute defines whether Echo Cancellation has to be enabled on this connection. If it is set to True, echo cancellation is enabled. If it is set to Fals… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.13 | ColumnvismAal2InitVadTimer | read-write | mandatory | This attribute defines the hangover time for VAD in milliseconds. Once the voice inactivity is detected, the gateway will wait for this duration before activat… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.14 | ColumnvismAal2CnfPktPeriod | read-write | mandatory | This object is used to configure the packetization period for a given codec. This pkt period has to be a valid entry in the profile table. Profile type and num… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.15 | ColumnvismAal2CidICSEnable | read-write | mandatory | This object is used to enable or disable the Idle Channel Suppresion for a cid. This can be specified while adding the cid and cannot be modified. When the Idl… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.16 | ColumnvismAal2CidState | read-only | mandatory | Indicates the state of the cid. active - the cid is in service and operational failed - the cid is in service but not operational, e.g. because the PVC that th… |
| 1.3.6.1.4.1.351.110.5.5.3.4.1.1.17 | ColumnvismAal2CidFailReason | read-only | mandatory | This object is used to indicate the cid failure reason. self: fail because of non-PVC alarm highLevel: fail because of PVC alarm both: fail because of both PVC… |
| 1.3.6.1.4.1.351.110.5.5.6 | NodevismSigGrp | |||
| 1.3.6.1.4.1.351.110.5.5.6.1 | TablevismHdlcChanTable | not-accessible | mandatory | This table is used for maintaining the statistics info for the HDLC channels on VISM. It also keeps track of some configurable parameters required for proper o… |
| 1.3.6.1.4.1.351.110.5.5.6.1.1 | RowvismHdlcChanEntry | not-accessible | mandatory | An entry for each HDLC channel. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.1 | ColumnvismHdlcChanNum | read-only | mandatory | This object is the index of this table. It refers to the ds0IfIndex in the dsx0VismCnfTable. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.2 | ColumnvismHdlcRowStatus | read-write | mandatory | This variable allows to add, delete or modify the entry. createAndGo: Use this to add an entry in this table. There are two case of creating a entry: 1) a ccs … |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.3 | ColumnvismHdlcMaxFrameSize | read-only | deprecated | This object describes the maximum frame size that is allowed on this HDLC channel. This value is not configurable. The value for this object is 264. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.4 | ColumnvismHdlcLcnNum | read-write | mandatory | This object describes LCN or the PVC channel number with which the HDLC channel is associated with. It is applicable only for trunking applications where the C… |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.5 | ColumnvismHdlcXmtFrames | read-only | mandatory | This object maintains the count of HDLC frames transmitted to the HDLC channel on VISM. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.6 | ColumnvismHdlcRcvFrames | read-only | mandatory | This object maintains the count of HDLC frames received from the HDLC channel on VISM. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.7 | ColumnvismHdlcRcvCrcErrors | read-only | mandatory | This object describes the count of HDLC frames dropped due to CRC errors in the frames received from the HDLC Channel. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.8 | ColumnvismHdlcRcvBufOverflows | read-only | mandatory | This object describes the count of HDLC receiver buffer overflow condition. This can occur if the rate of arrival of HDLC frames from the line is more than the… |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.9 | ColumnvismHdlcTxUnderflows | read-only | mandatory | This object describes the count of HDLC Tx underflow condition. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.10 | ColumnvismHdlcTxAbortFrames | read-only | mandatory | This object describes the count of HDLC Abort frames transmitted. |
| 1.3.6.1.4.1.351.110.5.5.6.1.1.11 | ColumnvismHdlcRxAbortFrames | read-only | mandatory | This object describes the count of HDLC Abort frames received. |
| 1.3.6.1.4.1.351.110.5.5.7 | NodevismCodecTemplateCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.5.7.1 | TablevismCodecTemplateCnfGrpTable | not-accessible | mandatory | This table defines the DSP templates that are applicable on a card basis. It defines the set of codecs supported in each template and the maximum number of DS0… |
| 1.3.6.1.4.1.351.110.5.5.7.1.1 | RowvismCodecTemplateCnfGrpEntry | not-accessible | mandatory | An entry is defined for each set of codecs supported. The codecs supported are a combination of : G.711Mu (PCM - Mu-law) G.711A (PCM - A-law) G.726/32 (ADPCM) … |
| 1.3.6.1.4.1.351.110.5.5.7.1.1.1 | ColumnvismCodecTemplateNum | read-only | mandatory | This attribute defines the index for the CodecTemplate table. Template number is input at the time of configuring a template using 'cnftemp' CLI command. |
| 1.3.6.1.4.1.351.110.5.5.7.1.1.2 | ColumnvismCodecSupported | read-only | mandatory | This attribute represents a bit map of Codecs supported in this template. Bit 0 - represents the G.711 Mu-law codec. Bit 1 - represents the G.711 A-law codec. … |
| 1.3.6.1.4.1.351.110.5.5.7.1.1.3 | ColumnvismCodecTemplateMaxChanCount | read-only | mandatory | The max. number of channels supported for this template. Based on the codec that is of the maximum complexity, the maximum no. of channels that can be supporte… |
| 1.3.6.1.4.1.351.110.5.5.8 | NodevismCasGrp | |||
| 1.3.6.1.4.1.351.110.5.5.8.1 | TablevismCasVariantTable | not-accessible | mandatory | This table contains configuration information about different CAS variants. |
| 1.3.6.1.4.1.351.110.5.5.8.1.1 | RowvismCasVariantEntry | not-accessible | mandatory | An entry in the vismCasVariantTable. Each entry consists of configuration information for a specific CAS variant. An entry may be created by specifying vismCas… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.1 | ColumnvismCasVariantName | read-only | mandatory | This object is a string identifier for the CAS variant. It is used as index to the table. The maximum length allowed is 64 bytes. |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.2 | ColumnvismCasFileName | read-write | mandatory | This object gives the name of the file which contains the signal definition and the Finite State Machine definition for the CAS variant. The name is supplied d… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.3 | ColumnvismCasTRinging | read-write | deprecated | This object gives the ringing time in seconds for the Cas Variant. The ringing will be on until this timer expires or until an off hook is received. |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.4 | ColumnvismCasDigitMethod | read-write | mandatory | The default digit method to be used for digit collection. If the digit method can not be derived from the digit map specified by the call agent in the XGCP mes… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.5 | ColumnvismCasInterdigitTpart | read-write | mandatory | This object represents the partial dial timing in seconds and is used along with a digit map as the inter-digit timer. The timer is not started untill the firs… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.6 | ColumnvismCasInterdigitTcrit | read-write | mandatory | This object represents the critical timing in seconds. If used along with a digit map, the timer is started when the last digit is received. i.e and when no mo… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.7 | ColumnvismCasInterdigitTMF | read-write | mandatory | This object represents the interdigit timeout value for MF digits. The timeout value is in seconds. |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.8 | ColumnvismCasVariantState | read-only | mandatory | This variable indicates the configuration status of the CAS variant. When the table entry is created, downloading of the file will be initiated and the state w… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.9 | ColumnvismCasRowStatus | read-write | mandatory | This variable allows to add, delete or modify the entry for a CAS variant. createAndGo: Use this to add an entry in this table, provided the vismCasVariantName… |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.10 | ColumnvismCasCountryCode | read-write | deprecated | Represents a case-insensitive 2-letter country code taken from ISO-3166. |
| 1.3.6.1.4.1.351.110.5.5.8.1.1.11 | ColumnvismCasVariantSource | read-write | mandatory | This object specifies where the file defining this CAS variant resides. 1. Unspecified. This value indicates that the location of the file is not specified her… |
| 1.3.6.1.4.1.351.110.5.5.8.2 | TablevismCasXgcpVariantTable | not-accessible | mandatory | An entry in this table is implicitly created/deleted when an entry in vismCasVariantTable is created/deleted in switching mode . |
| 1.3.6.1.4.1.351.110.5.5.8.2.1 | RowvismCasXgcpVariantEntry | not-accessible | mandatory | An entry in the vismCasXgcpVariantTable. |
| 1.3.6.1.4.1.351.110.5.5.8.2.1.1 | ColumnvismCasXgcpVariantName | read-only | mandatory | This object is a string identifier for the CAS variant. It is used as index to the table. |
| 1.3.6.1.4.1.351.110.5.5.8.2.1.2 | ColumnvismCasXgcpFileName | read-only | mandatory | This object gives the name of the file which contains the signal definition and the Finite State Machine definition for the CAS variant. |
| 1.3.6.1.4.1.351.110.5.5.8.2.1.3 | ColumnvismCasXgcpMaxReXmitTime | read-write | mandatory | This object represents the maximum timeout value in milli seconds, used for retransmitting unacknowledged XGCP messages at the Call Agent - CAS/PBX interface. … |
| 1.3.6.1.4.1.351.110.5.5.8.2.1.4 | ColumnvismCasXgcpInitialReXmitTime | read-write | mandatory | This object represents the initial timeout value in milli seconds, used for retransmitting unacknowledged XGCP messages at the Call Agent - CAS/PBX interface. … |
| 1.3.6.1.4.1.351.110.5.5.8.2.1.5 | ColumnvismCasXgcpMaxRetries | read-write | mandatory | This object specifies the number of retries for a message that exceeds vismCasXgcpMaxReXmitTime or vismCasXgcpInitialReXmitTime. |
| 1.3.6.1.4.1.351.110.5.5.9 | NodebearerConnGrp | |||
| 1.3.6.1.4.1.351.110.5.5.9.1 | TablebearerConnTable | not-accessible | mandatory | This table describes the statistical information available on a per-bearer connection basis. These values are applicable equally to an endpoint. However, a sep… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1 | RowbearerConnEntry | not-accessible | mandatory | Each entry in this table corresponds to a bearer connection, that was setup by binding an endpoint with VC/CID pair, either through CLI or SNMP. The statistica… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.1 | ColumnbearerEndptNum | read-only | mandatory | This attribute defines the index for the bearer connection Table. This refers to the same value as the index to the mgEndpoint Table ie. mgEndpointNumber |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.2 | ColumnbearerCid | read-only | mandatory | This attribute defines the CID (Channel ID associated with this bearer connection.This refers to the same value as vismAal2CidNum in the vismAal2CidCnfTable. |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.3 | ColumnbearerLcn | read-only | mandatory | This attribute defines the PVC or LCN number to which this bearer connection is associated with. This refers to the same value as in vismChanNum in vismChanCnf… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.4 | ColumnbearerSentPkts | read-only | mandatory | This attribute defines the count of packets sent towards the network since setup. |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.5 | ColumnbearerRcvdPkts | read-only | mandatory | This attribute defines the count of packets received from the network since setup. |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.6 | ColumnbearerSentOctets | read-only | mandatory | This attribute defines the count of bytes sent towards the network since this connection setup. |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.7 | ColumnbearerRcvdOctets | read-only | mandatory | This attribute defines the count of bytes received from the network since this connection setup. |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.8 | ColumnbearerLostPkts | read-only | mandatory | This attribute defines the count of packets lost in the egress direction (from the network). This is a computed number based on the expected number of packets … |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.9 | ColumnbearerJitter | read-only | mandatory | This attribute defines the jitter (a.k.a interarrival jitter) This value is determined by the DSP and obtained by the HOST processor upon querying the DSP on a… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.10 | ColumnbearerLatency | read-only | mandatory | This attribute defines the latency (a.k.a end-to-end average transmission delay for a voice packet. This value is expressed in units of milliseconds. Currently… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.11 | ColumnbearerAal2ExtAISCnts | read-only | mandatory | This object contains the number of external AIS aal2 Type3 packets received. External AIS - is a Alarm Indication Signal associated with a maintenance alarm de… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.12 | ColumnbearerAal2ExtRAICnts | read-only | mandatory | This object contains the number of external RAI aal2 Type3 packets received. External RAI - is a Remote Alarm Indication signal that is transmitted upstream fr… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.13 | ColumnbearerAal2ConnAISCnts | read-only | mandatory | This object contains the number of external Conn AIS aal2 Type2 packets received. External Conn AIS - is a Alarm Indicating Signal transmitted in the downstrea… |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.14 | ColumnbearerAal2ConnRDICnts | read-only | mandatory | This object contains the number of external Conn RDI (Remote Defect Ind.) aal2 Type2 packets received. External Conn RDI - is a signal transmitted upstream by … |
| 1.3.6.1.4.1.351.110.5.5.9.1.1.15 | ColumnbearerCntClrButton | read-write | mandatory | This object is used to clear bearerSentPkts, bearerRcvdPkts, bearerSentOctets, and bearerRcvdOctets. |
| 1.3.6.1.4.1.351.110.5.5.10 | NodevismSvcGrp | |||
| 1.3.6.1.4.1.351.110.5.5.10.1 | ScalarvismSvcTxSetups | read-only | mandatory | This is the number of Setup messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.2 | ScalarvismSvcRxSetups | read-only | mandatory | This is the number of Setup messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.3 | ScalarvismSvcTxCallProcs | read-only | mandatory | This is the number of Call proceeding messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.4 | ScalarvismSvcRxCallProcs | read-only | mandatory | This is the number of Call proceeding messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.5 | ScalarvismSvcTxConns | read-only | mandatory | This is the number of Connect messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.6 | ScalarvismSvcTxConnAcks | read-only | mandatory | This is the number of Connect ack messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.7 | ScalarvismSvcRxConns | read-only | mandatory | This is the number of Connect messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.8 | ScalarvismSvcRxConnAcks | read-only | mandatory | This is the number of Connect ack messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.9 | ScalarvismSvcTxReleases | read-only | mandatory | This is the number of Release messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.10 | ScalarvismSvcTxReleaseCompls | read-only | mandatory | This is the number of Release complete messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.11 | ScalarvismSvcRxReleases | read-only | mandatory | This is the number of Release messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.12 | ScalarvismSvcRxReleaseCompls | read-only | mandatory | This is the number of Release complete messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.13 | ScalarvismSvcTxRestarts | read-only | mandatory | This is the number of Restart messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.14 | ScalarvismSvcTxRestartAcks | read-only | mandatory | This is the number of Restart ack messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.15 | ScalarvismSvcRxRestarts | read-only | mandatory | This is the number of Restart messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.16 | ScalarvismSvcRxRestartAcks | read-only | mandatory | This is the number of Restart ack messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.17 | ScalarvismSvcTxResyncStrts | read-only | mandatory | This is the number of Resync start messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.18 | ScalarvismSvcTxResyncStrtAcks | read-only | mandatory | This is the number of Resync start ack messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.19 | ScalarvismSvcRxResyncStrts | read-only | mandatory | This is the number of Resync start messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.20 | ScalarvismSvcRxResyncStrtAcks | read-only | mandatory | This is the number of Resync start ack messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.21 | ScalarvismSvcTxResyncEnds | read-only | mandatory | This is the number of Resync end messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.22 | ScalarvismSvcTxResyncEndAcks | read-only | mandatory | This is the number of Resync end ack messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.23 | ScalarvismSvcRxResyncEnds | read-only | mandatory | This is the number of Resync end messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.24 | ScalarvismSvcRxResyncEndAcks | read-only | mandatory | This is the number of Resync end ack messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.25 | ScalarvismSvcTxBulkResyncs | read-only | mandatory | This is the number of Bulk resync messages sent to the PXM from the VISM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.26 | ScalarvismSvcRxBulkResyncs | read-only | mandatory | This is the number of Bulk resync messages received by the VISM from the PXM since VISM reset. |
| 1.3.6.1.4.1.351.110.5.5.10.27 | ScalarvismSvcCallProcExpiries | read-only | mandatory | Call proceeding expirations |
| 1.3.6.1.4.1.351.110.5.5.10.28 | ScalarvismSvcReleasExpiries | read-only | mandatory | Release completion expirations |
| 1.3.6.1.4.1.351.110.5.5.10.29 | ScalarvismSvcConnExpiries | read-only | mandatory | Connect expirations |
| 1.3.6.1.4.1.351.110.5.5.10.30 | ScalarvismSvcConnAckExpiries | read-only | mandatory | Connect ack expirations |
| 1.3.6.1.4.1.351.110.5.5.10.31 | ScalarvismSvcRestartExpiries | read-only | mandatory | Restart expirations |
| 1.3.6.1.4.1.351.110.5.5.10.32 | ScalarvismSvcResyncExpiries | read-only | mandatory | Resync expirations |
| 1.3.6.1.4.1.351.110.5.5.18 | NodevismCodecCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.5.18.1 | TablevismCodecCnfTable | not-accessible | mandatory | This table contains configuration information about different codecs and there packetization periods. |
| 1.3.6.1.4.1.351.110.5.5.18.1.1 | RowvismCodecCnfEntry | not-accessible | mandatory | An entry in the vismCodecCnf table. Each entry consists of packetization period information for a specific codec. All the entries in this table are implicitly … |
| 1.3.6.1.4.1.351.110.5.5.18.1.1.1 | ColumnvismCodecCnfIndex | read-only | mandatory | This object is a index to this table. 1 represents G.711u 2 represents G.711a 3 represents G.726 at rate 32 kbps 4 represents G.729a 5 represents G.729ab 6 rep… |
| 1.3.6.1.4.1.351.110.5.5.18.1.1.2 | ColumnvismCodecName | read-only | mandatory | This object holds the name of the codec for example index 1 will have G.711u as the codec name index 2 will have G.711a as the codec name and so on.... |
| 1.3.6.1.4.1.351.110.5.5.18.1.1.3 | ColumnvismCodecPktPeriod | read-write | mandatory | This object gives the packetization period for a particular codec in milli secs. for G.711a allowed values are 10 & 20 for G.711u allowed values are 10 & 20 fo… |
| 1.3.6.1.4.1.351.110.5.5.18.1.1.4 | ColumnvismCodecPreference | read-write | mandatory | This object contains the user configured preference for each codec. Lower the number, higher the preference of the codec . Since currently we only have 14 code… |
| 1.3.6.1.4.1.351.110.5.5.18.1.1.5 | ColumnvismCodecString | read-write | mandatory | The local connection option or SDP descriptor string that vism would get from the call agent for the codec to be used will be in the form of PCMU, PCMA, G726 a… |
| 1.3.6.1.4.1.351.110.5.5.18.1.1.6 | ColumnvismCodecIanaType | read-write | mandatory | The codecs are assigned types (numbers) by IANA. This object will contain such a number. In future we may have more numbers. currently by default we have PCMU … |
| 1.3.6.1.4.1.351.110.5.5.19 | NodevismSvcCnfGroups | |||
| 1.3.6.1.4.1.351.110.5.5.19.1 | NodevismSvcAtmQosGrp | |||
| 1.3.6.1.4.1.351.110.5.5.19.1.1 | ScalarvismSvcAtmQosCdv | read-write | mandatory | End-to-end cell delay variation used in voice SVC establishment. It is used to guarantee the quality of the route selected for a voice SVC. It is applicable to… |
| 1.3.6.1.4.1.351.110.5.5.19.1.2 | ScalarvismSvcAtmQosCtd | read-write | mandatory | End-to-end maximum cell transfer delay used in voice SVC establishment. It is used to guarantee the quality of the route selected for a voice SVC. It is applic… |
| 1.3.6.1.4.1.351.110.5.5.19.1.3 | ScalarvismSvcAtmQosClr | read-write | mandatory | Maximum Cell Loss Ratio used in voice SVC establishment. It is used to guarantee the quality of the route selected for a voice SVC. It is applicable to both AA… |
| 1.3.6.1.4.1.351.110.5.5.19.2 | NodevismSvcTrfScalingGrp | |||
| 1.3.6.1.4.1.351.110.5.5.19.2.1 | ScalarvismSvcTrfScalingFactor | read-write | mandatory | Traffic scaling Factor used to compute factored bandwidth which is used in ATM signaling to establish voice SVC. When this value is less than 100 it can be ref… |
| 1.3.6.1.4.1.351.110.5.5.19.3 | NodevismSvcAal2CidGrp | |||
| 1.3.6.1.4.1.351.110.5.5.19.3.1 | ScalarvismSvcAal2CidNumber | read-write | mandatory | The default AAL2 Channel IDentification (CID) number used for AAL2 SVC connections. |
| 1.3.6.1.4.1.351.110.5.5.20 | NodevismCardCacFailuresGrp | |||
| 1.3.6.1.4.1.351.110.5.5.20.1 | ScalarvismPortCacPvcAddFailures | read-only | mandatory | Total number of attempts to add or modify a PVC to VISM virtual port that were rejected by port level connection admission control. |
| 1.3.6.1.4.1.351.110.5.5.20.2 | ScalarvismPortCacSvcAddFailures | read-only | mandatory | Total number of attempts to add a SVC to VISM virtual port that were rejected by port level connection admission control. |
| 1.3.6.1.4.1.351.110.5.5.20.3 | ScalarvismVcCacPvcFailures | read-only | mandatory | Total number of attempts to admit voice connections over bearer PVC connections that were rejected by voice connection admission control. It is sum of all voic… |
| 1.3.6.1.4.1.351.110.5.5.20.4 | ScalarvismVcCacPvcUpspeedFailures | read-only | mandatory | Total number of attempts to upspeed voice connections over bearer PVC connections that were rejected by Port Level Connection Admission Control. |
| 1.3.6.1.4.1.351.110.5.5.20.5 | ScalarvismPortCacSvcUpspeedFailures | read-only | mandatory | Total number of attempts to upspeed voice connections over bearer SVC connections that were rejected by Port Level Connection Admission Control. |
| 1.3.6.1.4.1.351.110.6.1 | Nodebert | |||
| 1.3.6.1.4.1.351.110.6.1.1 | ScalarbertControl | read-write | mandatory | This object controls all the SET operations on this MIB group. acquireBert : Acquire BERT resources. cnfBert : Configure the required BERT test. startBert : Th… |
| 1.3.6.1.4.1.351.110.6.1.2 | ScalarbertResourceStatus | read-only | mandatory | All of bert resources can be used by only one user at a time. This gives the status of the resources. |
| 1.3.6.1.4.1.351.110.6.1.3 | ScalarbertOwner | read-only | mandatory | This refers to the user who owns the BERT resources. If the user is a CLI user, then this is username. If it is SV+, then this would be the IP address. For exa… |
| 1.3.6.1.4.1.351.110.6.1.4 | ScalarbertUserId | read-write | mandatory | This identifies the user who wants to do a SET operation on this group. This will be compared against bertOwner and access will be given only if it matches. He… |
| 1.3.6.1.4.1.351.110.6.1.5 | ScalarbertStatus | read-only | mandatory | This variable provides the status of BERT in the shelf. |
| 1.3.6.1.4.1.351.110.6.1.6 | ScalarbertSlotNumber | read-write | mandatory | specifies the physical slot number of the Service Module which is to run BERT For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-… |
| 1.3.6.1.4.1.351.110.6.1.7 | ScalarbertTestMedium | read-write | mandatory | specifies whether the bert is to test a port or an entire T1/E1 line. No default value for this, it has to be set if bert is configured. |
| 1.3.6.1.4.1.351.110.6.1.8 | ScalarbertPort | read-write | mandatory | specifies the port number for BERT. |
| 1.3.6.1.4.1.351.110.6.1.9 | ScalarbertLine | read-write | mandatory | specifies the line number for BERT. If the test medium is port, this represents the line to which the port belongs. |
| 1.3.6.1.4.1.351.110.6.1.10 | ScalarbertMode | read-write | mandatory | specifies the mode, the BERT module is to be configured for. |
| 1.3.6.1.4.1.351.110.6.1.11 | ScalarbertDeviceToLoop | read-write | mandatory | This shows the type of the end device and the type of the loopback used (latching/nonlatching/polynomial). |
| 1.3.6.1.4.1.351.110.6.1.12 | ScalarbertDS0DPIterationCount | read-write | mandatory | The Iteration Register needs to be programmed in SRM when DSO drop loop option is selected in bertDeviceToLoop. The value to be programmed there is minus one o… |
| 1.3.6.1.4.1.351.110.6.1.13 | ScalarbertPattern | read-write | mandatory | This variable determines BERT pattern to be transmitted. |
| 1.3.6.1.4.1.351.110.6.1.14 | ScalarbertLoopback | read-write | mandatory | specifies the type of loopback to be (d)established. |
| 1.3.6.1.4.1.351.110.6.1.15 | ScalarbertLoopbackOperation | read-write | mandatory | specifies the operation of loopback (up or down). |
| 1.3.6.1.4.1.351.110.6.1.16 | ScalarbertDS0Speed | read-only | mandatory | represents the ds0 speed of the test running. |
| 1.3.6.1.4.1.351.110.6.1.17 | ScalarbertTimeSlots | read-only | mandatory | represents the number of ds0s in the test medium chosen. |
| 1.3.6.1.4.1.351.110.6.1.18 | ScalarbertStartTime | read-only | mandatory | The syntax is hh:mm:ss The time zone is as configured in the shelf. |
| 1.3.6.1.4.1.351.110.6.1.19 | ScalarbertStartDate | read-only | mandatory | On MGX 8220, the syntax is mm/dd/yy On MGX 8850, the syntax is mm/dd/yyyy |
| 1.3.6.1.4.1.351.110.6.1.20 | ScalarbertBitCount | read-only | mandatory | This shows the number of bits transmitted. |
| 1.3.6.1.4.1.351.110.6.1.21 | ScalarbertBitErrorCount | read-only | mandatory | This shows the number of bits received in error. |
| 1.3.6.1.4.1.351.110.6.1.22 | ScalarbertErrorInjectCount | read-only | mandatory | This shows the number of times error was injected. |
| 1.3.6.1.4.1.351.110.6.1.23 | ScalarbertCleanupAction | read-only | mandatory | When the BERT has to be stopped or aborted (due to card state changes), this object would give the exact action to take. The bert related changes to the shelf,… |
| 1.3.6.1.4.1.351.110.6.1.24 | ScalarbertAbortReason | read-only | mandatory | when the BERT is aborted, this object would give the reason for that. |
| 1.3.6.1.4.1.351.110.6.1.25 | ScalarbertDDSSeekResultsTableFirstIndex | read-only | mandatory | Denotes the index of the oldest entry in the table. A value of zero means that there are no entries in the table. |
| 1.3.6.1.4.1.351.110.6.1.26 | ScalarbertDDSSeekResultsTableLastIndex | read-only | mandatory | Denotes the index of the latest entry in the table. A value of zero means that there are no entries in the table. |
| 1.3.6.1.4.1.351.110.6.1.27 | TablebertDDSSeekResultsTable | not-accessible | mandatory | A list of detected DDS codes. |
| 1.3.6.1.4.1.351.110.6.1.27.1 | RowbertDDSSeekResultsTableEntry | not-accessible | mandatory | An entry in the detected DDS codes table. |
| 1.3.6.1.4.1.351.110.6.1.27.1.1 | ColumnbertDDSSeekResultsTableIndex | read-only | mandatory | Denotes the serial number of the entry in the table. |
| 1.3.6.1.4.1.351.110.6.1.27.1.2 | ColumnbertDDSCode | read-only | mandatory | Denotes the type of DDS code detected. |
| 1.3.6.1.4.1.351.110.6.1.28 | TablebertSupportedTestsTable | not-accessible | mandatory | A list of supported tests for a given SM. |
| 1.3.6.1.4.1.351.110.6.1.28.1 | RowbertSupportedTestsTableEntry | not-accessible | mandatory | A general supported tests entry. |
| 1.3.6.1.4.1.351.110.6.1.28.1.1 | ColumnbertSupportedTestsTableIndex | read-only | mandatory | This index is the physical slot number of the Service Module whose entry it represents in the table. For MGX 8220, the range is 5-14. For MGX 8850, the range i… |
| 1.3.6.1.4.1.351.110.6.1.28.1.2 | ColumnbertSupportFlag | read-only | mandatory | 'yes' if the table entry correctly represents the supported tests for the SM on the corresponding slot. 'no' if no tests at all are supported. |
| 1.3.6.1.4.1.351.110.6.1.28.1.3 | ColumnbertTestMediumMask | read-only | mandatory | Every test medium is represented by a bit of mask. Bits 0-1 are valid in this integer. The meaning of the mask can be understood from the example below: TestMe… |
| 1.3.6.1.4.1.351.110.6.1.28.1.4 | ColumnbertModeMask | read-only | mandatory | Every mode is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: Mode | SM su… |
| 1.3.6.1.4.1.351.110.6.1.28.1.5 | ColumnbertDeviceToLoopMask | read-only | mandatory | Every class of devices to loop is represented by 6 bits of mask. Bits 0-29 are valid in this integer. The meaning of the mask can be understood from the exampl… |
| 1.3.6.1.4.1.351.110.6.1.28.1.6 | ColumnbertPatternMask | read-only | mandatory | Every class of patterns is represented by 2 bits of mask. Bits 0-3 are valid in this integer. The meaning of the mask can be understood from the example below:… |
| 1.3.6.1.4.1.351.110.6.1.28.1.7 | ColumnbertLoopbackMask | read-only | mandatory | Every loopback is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: Loopback… |
| 1.3.6.1.4.1.351.110.6.1.28.1.8 | ColumnbertCardT1E1Type | read-only | mandatory | Specifies whether a t1 or e1 card. |
| 1.3.6.1.4.1.351.110.6.3 | NodeonlineDiagnostics | |||
| 1.3.6.1.4.1.351.110.6.3.1 | ScalardiagType | read-only | mandatory | This is used to identify the type of diagnostics. When a trap is sent to report diagnostics results this is used as a varbind to indicate the type of diagnosti… |
| 1.3.6.1.4.1.351.110.6.3.2 | ScalardiagResult | read-only | mandatory | This is used to indicate the result of the diagnostics tests in traps. |
| 1.3.6.1.4.1.351.110.6.3.3 | ScalardiagTestId | read-only | mandatory | This is used to indicate the test number of the diagnostics test that failed. |
| 1.3.6.1.4.1.351.130.1 | NodeparSelfNode | |||
| 1.3.6.1.4.1.351.130.1.1 | ScalarparSnNodeId | read-write | mandatory | This object specifies the node number of the node. When the network manager tries to modify the value of this object, a message is sent node state machine whic… |
| 1.3.6.1.4.1.351.130.1.2 | ScalarparSnNodeIP | read-write | mandatory | This object specifies the IP address for routing node and is used for communication with SV+. |
| 1.3.6.1.4.1.351.130.1.3 | ScalarparSnNodeName | read-write | mandatory | This object specifies the name of the node and is unique among all the nodes in the network. Whenever the name of the node is changed, AutoRoute has to propaga… |
| 1.3.6.1.4.1.351.130.1.4 | ScalarparSnRevision | read-only | mandatory | This object specifies the primary revision of the PAR running on the node. Format: cc.c.cc Where: c = one ascii character |
| 1.3.6.1.4.1.351.130.1.5 | ScalarparSnNodeAlarmStatus | read-only | mandatory | This object specifies the type of alarm on the node. If there is no alarm the value of this object is none(1). If there is a minor alarm the value of this obje… |
| 1.3.6.1.4.1.351.130.1.6 | ScalarparSnNumberOfTrunks | read-only | mandatory | This object specifies the number of trunks attached to the node. |
| 1.3.6.1.4.1.351.130.2 | NodeparInterfaces | |||
| 1.3.6.1.4.1.351.130.2.1 | TableparIfTable | not-accessible | mandatory | Table of all logical interfaces supported by PAR |
| 1.3.6.1.4.1.351.130.2.1.1 | RowparIfEntry | not-accessible | mandatory | Entries for logical interfaces. |
| 1.3.6.1.4.1.351.130.2.1.1.1 | ColumnparIfLogicalInterface | read-only | mandatory | This object specifies the logical interface number assigned by Platform Software |
| 1.3.6.1.4.1.351.130.2.1.1.2 | ColumnparIfType | read-write | mandatory | Specifies the type of interface - uni, nni or clock. uni(1) interface is for user ports and trunks may be either nni or uni. Default type of the interface is u… |
| 1.3.6.1.4.1.351.130.2.1.1.3 | ColumnparIfOperStatus | read-only | mandatory | This object specifies the operation status of the interface. For interfaces of type uni(1) the status is either up(1) or failed(3) as reported by platform. For… |
| 1.3.6.1.4.1.351.130.2.1.1.4 | ColumnparIfTxBw | read-only | mandatory | This object specifies the transmit bandwidth for the interface in units of cells per second. |
| 1.3.6.1.4.1.351.130.2.1.1.5 | ColumnparIfRxBw | read-only | mandatory | This object specifies the receive bandwidth for the interface in units of cells per second. |
| 1.3.6.1.4.1.351.130.2.1.1.6 | ColumnparIfMaxConn | read-only | mandatory | This object specifies the maximum number of connections that can be configured over the interface. |
| 1.3.6.1.4.1.351.130.2.1.1.7 | ColumnparIfHiAddrMin | read-only | mandatory | This object specifies the minimum VPI that PAR can use for configuring connection in the interface. |
| 1.3.6.1.4.1.351.130.2.1.1.8 | ColumnparIfHiAddrMax | read-only | mandatory | This object specifies the maximum VPI that PAR can use for configuring connection in the interface. |
| 1.3.6.1.4.1.351.130.2.1.1.9 | ColumnparIfLoAddrMin | read-only | mandatory | This object specifies the minimum VCI that PAR can use for configuring connection in the interface. |
| 1.3.6.1.4.1.351.130.2.1.1.10 | ColumnparIfLoAddrMax | read-only | mandatory | This object specifies the maximum VCI that PAR can use for configuring connection in the interface. |
| 1.3.6.1.4.1.351.130.2.2 | TableparTrkTable | not-accessible | mandatory | Trunk parameters |
| 1.3.6.1.4.1.351.130.2.2.1 | RowparTrkEntry | not-accessible | mandatory | Entries for logical interfaces configured as trunks (parIfType nni). |
| 1.3.6.1.4.1.351.130.2.2.1.1 | ColumnparTrkId | read-only | mandatory | This object specifies the logical trunk number associated with the trunk at the local node. |
| 1.3.6.1.4.1.351.130.2.2.1.2 | ColumnparTrkStatReserve | read-write | mandatory | Specifies the bandwidth reserved as Statistical Reserve on the trunk in units of cells per second. This object cannot take a value beyond the bandwidth capacit… |
| 1.3.6.1.4.1.351.130.2.2.1.3 | ColumnparTrkCnfgCcRestrict | read-write | mandatory | This object specifies the operators preference for routing control plane traffic on the interface. If the object is set to False, then the interface may be cho… |
| 1.3.6.1.4.1.351.130.2.2.1.4 | ColumnparTrkCnfgLineType | read-write | mandatory | This object specifies the type of interface terrestrial or satellite. The interfaces configured as terrestrial(1) are preferred over those configured as satell… |
| 1.3.6.1.4.1.351.130.2.2.1.5 | ColumnparTrkCnfgPassSync | read-write | mandatory | This object specifies whether the trunk can be used to pass clock sync. If the value of this object is True, clock can be synchronized through the trunk; other… |
| 1.3.6.1.4.1.351.130.2.2.1.6 | ColumnparTrkCnfgDerouteDelay | read-write | mandatory | This object specifies the value of deroute delay timer in seconds. |
| 1.3.6.1.4.1.351.130.2.2.1.7 | ColumnparTrkCnfgTrafficClassFst | read-write | mandatory | This object indicates whether Foresight traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.8 | ColumnparTrkCnfgTrafficClassFr | read-write | mandatory | This object indicates whether Frame Relay traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.9 | ColumnparTrkCnfgTrafficClassNts | read-write | mandatory | This object indicates whether Non-Time Stamped traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.10 | ColumnparTrkCnfgTrafficClassTs | read-write | mandatory | This object indicates whether Time Stamped traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.11 | ColumnparTrkCnfgTrafficClassVoice | read-write | mandatory | This object indicates whether Voice traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.12 | ColumnparTrkCnfgTrafficClassCbr | read-write | mandatory | This object indicates whether Constant Bit Rate traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.13 | ColumnparTrkCnfgTrafficClassVbr | read-write | mandatory | This object indicates whether Variable Bit Rate traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.14 | ColumnparTrkCnfgTrafficClassAbr | read-write | mandatory | This object indicates whether Available Bit Rate traffic can be routed over the trunk. If the value is True it can be rerouted otherwise not. |
| 1.3.6.1.4.1.351.130.2.2.1.15 | ColumnparTrkCnfgAdminStatus | read-write | mandatory | This object can be used to add or delete the trunk. The value of this object can be set to add(1) only if the parIfOperStatus is up. The value can be set to de… |
| 1.3.6.1.4.1.351.130.2.2.1.16 | ColumnparTrkCnfgRoutingCost | read-write | mandatory | This object specifies the cost associated with the trunk for the purpose of routing the connections. This object has significance if cost based routing feature… |
| 1.3.6.1.4.1.351.130.2.2.1.17 | ColumnparTrkCnfgVccConids | read-write | mandatory | The max number of routing resource available on the trunk for VCC connections. |
| 1.3.6.1.4.1.351.130.2.2.1.18 | ColumnparTrkCnfgVpcConids | read-write | mandatory | The max number of routing resource available on the trunk for VPC connections |
| 1.3.6.1.4.1.351.130.2.2.1.19 | ColumnparTrkLocalSlotNumber | read-only | mandatory | This object specifies the slot number of the interface card associated with the trunk at the local node. |
| 1.3.6.1.4.1.351.130.2.2.1.20 | ColumnparTrkLocalPortNumber | read-only | mandatory | This object specifies the port number of the interface card associated with the trunk at the local node. |
| 1.3.6.1.4.1.351.130.2.2.1.21 | ColumnparTrkLocalVTrunkId | read-only | mandatory | This object specifies the Virtual trunk of the interface card associated with the trunk at the local node. The value of this object is between 1 and 254, inclu… |
| 1.3.6.1.4.1.351.130.2.2.1.22 | ColumnparTrkRemoteNodeId | read-only | mandatory | This object specifies the node number of the node attached to the remote end of the trunk. |
| 1.3.6.1.4.1.351.130.2.2.1.23 | ColumnparTrkRemoteTrunkId | read-only | mandatory | This object specifies the logical trunk number at the node on the remote end of the trunk. |
| 1.3.6.1.4.1.351.130.2.2.1.24 | ColumnparTrkRemoteSlotNumber | read-only | mandatory | This object specifies the slot number of the interface card to which the trunk is attached on the remote node. |
| 1.3.6.1.4.1.351.130.2.2.1.25 | ColumnparTrkRemotePortNumber | read-only | mandatory | This object specifies the port number of the interface card to which the trunk is attached on the remote node. |
| 1.3.6.1.4.1.351.130.2.2.1.26 | ColumnparTrkRemoteVTrunkId | read-only | mandatory | This object specifies the Virtual trunk of the interface card associated with the trunk at the remote node. The value of this object is between 1 and 254, incl… |
| 1.3.6.1.4.1.351.130.2.2.1.27 | ColumnparTrkRemoteNodeIP | read-only | mandatory | This object specifies the IP address for the Remote node, used for communication with NMS |
| 1.3.6.1.4.1.351.130.2.2.1.28 | ColumnparTrkRemoteNodeType | read-only | mandatory | Specifies the type of the node. |
| 1.3.6.1.4.1.351.130.2.2.1.29 | ColumnparTrkRemoteNodeName | read-only | mandatory | This object specifies the name of the remote node and is unique among all the nodes in the network. |
| 1.3.6.1.4.1.351.130.2.2.1.30 | ColumnparTrkAlarmStatus | read-only | mandatory | This object specifies the severity of the alarm on the trunk. If there is no alarm the value of this object is none(1). If there is a minor alarm the value of … |
| 1.3.6.1.4.1.351.130.2.2.1.31 | ColumnparTrkAlarmType | read-only | mandatory | This object specifies the type of alarm on the trunk. The value of this object has no significance if parTrunkAlarmStatus indicates no alarm. resources unavail… |
| 1.3.6.1.4.1.351.130.2.2.1.32 | ColumnparTrkBwCapacity | read-only | mandatory | Specifies the bandwidth capacity of the trunk. |
| 1.3.6.1.4.1.351.130.2.2.1.33 | ColumnparTrkLineLoad | read-only | mandatory | Specifies the bandwidth used by the connections routed over the trunk. |
| 1.3.6.1.4.1.351.130.2.3 | TableparTrkLoadTable | not-accessible | mandatory | Trunk Load Information |
| 1.3.6.1.4.1.351.130.2.3.1 | RowparTrkLoadEntry | not-accessible | mandatory | Load info for logical interfaces configured as trunks (parIfType nni). |
| 1.3.6.1.4.1.351.130.2.3.1.1 | ColumnparTrkLoadXmtUsedCbr | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for CBR traffic. |
| 1.3.6.1.4.1.351.130.2.3.1.2 | ColumnparTrkLoadRcvUsedCbr | read-only | mandatory | This object specifies the used bandwidth in the receive direction for CBR traffic |
| 1.3.6.1.4.1.351.130.2.3.1.3 | ColumnparTrkLoadXmtUsedVbr | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for VBR. |
| 1.3.6.1.4.1.351.130.2.3.1.4 | ColumnparTrkLoadRcvUsedVbr | read-only | mandatory | This object specifies the used bandwidth in the receive direction for VBR. |
| 1.3.6.1.4.1.351.130.2.3.1.5 | ColumnparTrkLoadXmtUsedAbr | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for ABR. |
| 1.3.6.1.4.1.351.130.2.3.1.6 | ColumnparTrkLoadRcvUsedAbr | read-only | mandatory | This object specifies the used bandwidth in the receive direction for ABR. |
| 1.3.6.1.4.1.351.130.2.3.1.7 | ColumnparTrkLoadXmtUsedNts | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for Non-Time Stamped. |
| 1.3.6.1.4.1.351.130.2.3.1.8 | ColumnparTrkLoadRcvUsedNts | read-only | mandatory | This object specifies the used bandwidth in the receive direction for Non-Time Stamped. |
| 1.3.6.1.4.1.351.130.2.3.1.9 | ColumnparTrkLoadXmtUsedTs | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for Time-Stamped. |
| 1.3.6.1.4.1.351.130.2.3.1.10 | ColumnparTrkLoadRcvUsedTs | read-only | mandatory | This object specifies the used bandwidth in the receive direction for Time-Stamped. |
| 1.3.6.1.4.1.351.130.2.3.1.11 | ColumnparTrkLoadXmtUsedVoice | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for Voice. |
| 1.3.6.1.4.1.351.130.2.3.1.12 | ColumnparTrkLoadRcvUsedVoice | read-only | mandatory | This object specifies the used bandwidth in the receive direction for Voice. |
| 1.3.6.1.4.1.351.130.2.3.1.13 | ColumnparTrkLoadXmtUsedBdataA | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for Busty Data A. |
| 1.3.6.1.4.1.351.130.2.3.1.14 | ColumnparTrkLoadRcvUsedBdataA | read-only | mandatory | This object specifies the used bandwidth in the receive direction for Bursty Data A. |
| 1.3.6.1.4.1.351.130.2.3.1.15 | ColumnparTrkLoadXmtUsedBdataB | read-only | mandatory | This object specifies the used bandwidth in the transmit direction for Bursty Data B. |
| 1.3.6.1.4.1.351.130.2.3.1.16 | ColumnparTrkLoadRcvUsedBdataB | read-only | mandatory | This object specifies the used bandwidth in the receive direction for Bursty Data B. |
| 1.3.6.1.4.1.351.130.2.3.1.17 | ColumnparTrkLoadVccConidsUsed | read-only | mandatory | This object specifies the number of conids used for VCCs (not used) on the trunk. |
| 1.3.6.1.4.1.351.130.2.3.1.19 | ColumnparTrkLoadVpcConidsUsed | read-only | mandatory | This object specifies the number of conids Used for VPCs (not used) on the trunk. |
| 1.3.6.1.4.1.351.130.3 | NodeparConnection | |||
| 1.3.6.1.4.1.351.130.3.1 | TableparConnectionTable | not-accessible | mandatory | Connections Mastered or slaved by the node. |
| 1.3.6.1.4.1.351.130.3.1.1 | RowparConnectionEntry | not-accessible | mandatory | Entries for connections mastered or slaved by the node. |
| 1.3.6.1.4.1.351.130.3.1.1.1 | ColumnparConnLocalSlot | read-only | mandatory | This object specifies the slot number part of the local endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.2 | ColumnparConnLocalPort | read-only | mandatory | This object specifies the port number part of the local endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.3 | ColumnparConnLocalVpi | read-only | mandatory | This object specifies the Virtual Path Identifier part of the local endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.4 | ColumnparConnLocalVci | read-only | mandatory | This object specifies the Virtual Channel Identifier part of the local endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.5 | ColumnparConnMasterShip | read-only | mandatory | This object specifies whether this end of the connection is the master or the slave of the connection. |
| 1.3.6.1.4.1.351.130.3.1.1.6 | ColumnparConnLocalVcIndx | read-only | mandatory | This object specifies the Virtual Connection Index at this node. It is used by Network Management to correlate this end of the connection with the remote end. |
| 1.3.6.1.4.1.351.130.3.1.1.7 | ColumnparConnLocalEndpt | read-only | mandatory | This object specifies the actual physical connection endpoint at the local node. |
| 1.3.6.1.4.1.351.130.3.1.1.8 | ColumnparConnRemoteNodeName | read-only | mandatory | This object specifies the node name of the remote endpoint. For a intra-switch connection or feeder connection this object would specify the self node name. |
| 1.3.6.1.4.1.351.130.3.1.1.9 | ColumnparConnRemoteSlot | read-only | mandatory | This object specifies the slot number part of the remote endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.10 | ColumnparConnRemotePort | read-only | mandatory | This object specifies the port number part of the remote endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.11 | ColumnparConnRemoteVpi | read-only | mandatory | This object specifies the VPI part of the remote endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.12 | ColumnparConnRemoteVci | read-only | mandatory | This object specifies the VCI part of the remote endpoint connection address. |
| 1.3.6.1.4.1.351.130.3.1.1.13 | ColumnparConnRemoteVcIndx | read-only | mandatory | This object specifies the Virtual Connection Index at the remote node. It is used by Network Management to correlate this end of the connection with the remote… |
| 1.3.6.1.4.1.351.130.3.1.1.14 | ColumnparConnOperStatus | read-only | mandatory | This object specifies the status of connection as known and determined by PAR. The status shall be OK if there is an abit alarm on the connection. |
| 1.3.6.1.4.1.351.130.3.1.1.15 | ColumnparConnAdminStatus | read-write | mandatory | This object is used by the operator to reroute or down/up a connection. The value of this object is up when the connection is created. If the value of the obje… |
| 1.3.6.1.4.1.351.130.3.1.1.16 | ColumnparConnRoute | read-only | mandatory | This object specifies the current path on which the connection is routed. A value of this object is valid only if parConnOperStatus is routed. Null string spec… |
| 1.3.6.1.4.1.351.130.3.1.1.17 | ColumnparConnRemoteEndpt | read-only | mandatory | This object specifies the actual physical connection endpoint at the remote end of the connection. It shall be known only if the connection is a local(DAX) con… |
| 1.3.6.1.4.1.351.130.3.1.1.18 | ColumnparPrefRoute | read-write | mandatory | This object specifies the preferred path for the connection. Null string specifies that the connection does not have a preferred route. Format: Nodename {Trk W… |
| 1.3.6.1.4.1.351.130.3.1.1.19 | ColumnparConnFailRsn | read-only | mandatory | This object specifies a reason code for the failure of the connection. |
| 1.3.6.1.4.1.351.130.3.1.1.20 | ColumnparRrtFailRsn | read-only | mandatory | This object specifies the Reason of failure of a connection to route. |
| 1.3.6.1.4.1.351.130.3.1.1.21 | ColumnparConnRstrTyp | read-only | mandatory | This object specifies the Route restriction of a connection. The possible values are no restriction, terrestrial line restriction or sattelite line restriction. |
| 1.3.6.1.4.1.351.130.3.1.1.22 | ColumnparConnRstrZcs | read-only | mandatory | This object specifies whether ZCS lines should be avoided or not. The possible values are no restriction, terrestrial line restriction or sattelite line restri… |
| 1.3.6.1.4.1.351.130.3.1.1.23 | ColumnparConnCos | read-only | mandatory | This object specifies the COS for the connection. |
| 1.3.6.1.4.1.351.130.4 | NodeparNetworkClock | |||
| 1.3.6.1.4.1.351.130.4.1 | TableparClockTable | not-accessible | mandatory | Table of clock sources available to PAR |
| 1.3.6.1.4.1.351.130.4.1.1 | RowparClockEntry | not-accessible | mandatory | Each entry represent a clock source iavailable to PAR |
| 1.3.6.1.4.1.351.130.4.1.1.1 | ColumnparClockIndex | read-only | mandatory | This clock index is assigned by PAR. This object is used to index into parClockTable |
| 1.3.6.1.4.1.351.130.4.1.1.2 | ColumnparClockType | read-write | mandatory | Specifies the type of clock - Primary, Secondary, Tertiary |
| 1.3.6.1.4.1.351.130.4.1.1.3 | ColumnparClockSource | read-only | mandatory | Specifies source of the clock - Internal, Interface, External |
| 1.3.6.1.4.1.351.130.4.1.1.4 | ColumnparClockCurSource | read-only | mandatory | Specifies whether clock source is a current clock source or not. The value is true if the cloock source is current and false otherwise |
| 1.3.6.1.4.1.351.130.4.1.1.5 | ColumnparClockSourceId | read-write | mandatory | Specifies identification of the clock - for example - if clock source is `Interface' then this field will carry logical interface number |
| 1.3.6.1.4.1.351.130.4.1.1.6 | ColumnparClockPath | read-only | mandatory | Describes the path used for clock synchronization |
| 1.3.6.1.4.1.351.130.5 | NodeparConfigParms | |||
| 1.3.6.1.4.1.351.130.5.1 | NodeparVsiConfigParms | |||
| 1.3.6.1.4.1.351.130.5.2 | NodeparCmParms | |||
| 1.3.6.1.4.1.351.130.5.2.1 | ScalarparCmParmsMaxRoutingBundle | read-write | mandatory | This object specifies the maximum number of connections that can be routed in one routing cycle. |
| 1.3.6.1.4.1.351.130.5.2.2 | ScalarparCmParmsRerouteTimer | read-write | mandatory | This object specifies the minimum time after which a connection is routed once it has been successfully routed. |
| 1.3.6.1.4.1.351.130.5.2.3 | ScalarparCmParmsResetTimer | read-write | mandatory | This object specifies whether the reroute timer should be reset if the path for routed connection failed. If the value of the object is True the timer is reset… |
| 1.3.6.1.4.1.351.130.5.2.4 | ScalarparCmParmsDnUpPerPass | read-write | mandatory | This object specifies the maximum number of connections that are upped or down in one schedule of down connection state machine. |
| 1.3.6.1.4.1.351.130.5.2.5 | ScalarparCmParmsDnUpTimer | read-write | mandatory | This object specifies the minimum time interval (in milliseconds) between two schedules of the down connection state machine. |
| 1.3.6.1.4.1.351.130.5.2.6 | ScalarparCmParmsRrtErrsPerCycle | read-write | mandatory | This object specifies the threshold for number of failures to route a connection before it is moved into the wait group. If the value of this object is 0 the f… |
| 1.3.6.1.4.1.351.130.5.2.7 | ScalarparCmParmsRrtCycleInterval | read-write | mandatory | This object specifies the time (in minutes) for which no attempt is made to route a connection in the wait group. |
| 1.3.6.1.4.1.351.130.5.2.8 | ScalarparCmParmsMaxRrtCycles | read-write | mandatory | This object specifies the number of times a connection is added to the wait group before declaring it unroutable. |
| 1.3.6.1.4.1.351.130.5.2.9 | ScalarparCmParmsRrtPauseTime | read-write | mandatory | This object specifies the time interval (in milliseconds) between two routing cycles. |
| 1.3.6.1.4.1.351.130.5.2.10 | ScalarparCmParmsMaxUpdates | read-write | mandatory | This object specifies the maximum number of connection management updates that are sent by the node in schedule.. |
| 1.3.6.1.4.1.351.130.5.2.11 | ScalarparCmParmsRerouteGroups | read-write | mandatory | This object specifies the total number of reroute groups. |
| 1.3.6.1.4.1.351.130.5.2.12 | ScalarparCmParmsMinRrGroupSize | read-write | mandatory | This object specifies the minimum size of reroute group in Cell Load Units. |
| 1.3.6.1.4.1.351.130.5.2.13 | ScalarparCmParmsRrGroupInc | read-write | mandatory | This object specifies the increment of reroute group size (in Cell Load Units) between adjacent groups. |
| 1.3.6.1.4.1.351.130.5.2.14 | ScalarparCmParmsCostBased | read-write | mandatory | This object can be configured to enable or disable cost based routing feature. If the value of this object is True the feature is enabled else it is disabled. |
| 1.3.6.1.4.1.351.130.5.2.15 | ScalarparCmParmsUseCache | read-write | mandatory | This object can be configured to enable or disable hop based route selection from using cache of precomputed routes. If the value of this object is True the fe… |
| 1.3.6.1.4.1.351.130.5.2.16 | ScalarparCmParmsUseDelay | read-write | mandatory | This object can be configured to enable or disable cost based route selection from considering end-to-end delay associated with the routes. If the value of thi… |
| 1.3.6.1.4.1.351.130.5.2.17 | ScalarparCmParmMaxViaCons | read-write | mandatory | This object specifies the maximum number of via user connections that can be routed through the node. |
| 1.3.6.1.4.1.351.130.5.3 | NodeparMnUpdt | |||
| 1.3.6.1.4.1.351.130.5.3.1 | ScalarparMnUpdtInterval | read-write | mandatory | This object specifies the timer interval (in seconds) for the mandatory update state machine. |
| 1.3.6.1.4.1.351.130.5.3.2 | ScalarparMnUpdtNodesPerInt | read-write | mandatory | This object specifies the maximum number of nodes to which mandatory updates can be sent per interval. |
| 1.3.6.1.4.1.351.130.5.3.3 | ScalarparMnUpdtBatchSend | read-write | mandatory | This object specifies whether mandatory updates to any node are sent one at a time or all in one go. If the value of this object is True, all mandatory updates… |
| 1.3.6.1.4.1.351.130.5.4 | NodeparSwFunc | |||
| 1.3.6.1.4.1.351.130.5.4.1 | ScalarparSwFuncAbrVsvd | read-write | mandatory | This object enables/disables the ABR standard with VSVD. The feature is enabled if the value of the object is True. |
| 1.3.6.1.4.1.351.130.5.4.2 | ScalarparSwFuncNodeType | read-write | mandatory | This object specifies whether the node is a routing node or a feeder node. To configure the node from a routing(1) node to feeder(2) node the node should be pa… |
| 1.3.6.1.4.1.351.130.5.5 | NodeparOnOff | |||
| 1.3.6.1.4.1.351.130.5.5.1 | ScalarparOnOffBackgroundUpdt | read-write | mandatory | This object can be used to enable or disable Background updates. If the value of the object is True Background updates are enabled; otherwise they are disabled. |
| 1.3.6.1.4.1.351.130.5.5.2 | ScalarparOnOffDynamicBwAlloc | read-write | mandatory | This object can be used to enable or disable Bandwidth state machine. If the value of the object is True Bandwidth state machine is enabled; otherwise it is di… |
| 1.3.6.1.4.1.351.130.5.5.3 | ScalarparOnOffCmUpdts | read-write | mandatory | This object can be used to enable or disable Connection management updates. If the value of the object is True Connection management updates are enabled; other… |
| 1.3.6.1.4.1.351.130.5.5.4 | ScalarparOnOffRouting | read-write | mandatory | This object can be used to enable or disable connection routing. If the value of the object is True routing is enabled; otherwise it is disabled. |
| 1.3.6.1.4.1.351.130.5.5.5 | ScalarparOnOffCommFailTest | read-write | mandatory | This object can be used to enable or disable Comm Fail Test. If the value of the object is True Comm Fail test is enabled; otherwise it is disabled. |
| 1.3.6.1.4.1.351.130.5.5.6 | ScalarparOnOffDrtDelay | read-write | mandatory | This object can be used to enable or disable Deroute Delay feature. If the value of the object is True Derote delay feature is enabled; otherwise it is disable… |
| 1.3.6.1.4.1.351.130.5.5.7 | ScalarparOnOffRenumRec | read-write | mandatory | This object can be used to enable or disable Renumber recovery feature. If the value of the object is True renumber recovery feature is enabled; otherwise it i… |
| 1.3.6.1.4.1.351.130.5.5.8 | ScalarparOnOffCommBreak | read-write | mandatory | This object can be used to enable or disable Comm Break Test. If the value of the object is True Comm Break Test feature is enabled; otherwise it is disabled. |
| 1.3.6.1.4.1.351.130.5.6 | NodeparSysParms | |||
| 1.3.6.1.4.1.351.130.5.6.1 | ScalarparSysParmsTsPacketAge | read-write | mandatory | Time Stamped packets older than this value (in milliseconds) are discarded. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.2 | ScalarparSysParmsConnFail | read-write | mandatory | This object specifies whether the connections to a node should be failed when comm fail is declared with the node. If the value of this object is True the conn… |
| 1.3.6.1.4.1.351.130.5.6.3 | ScalarparSysParmsVcPollRate | read-only | mandatory | This object specifies the rate at which VC statistics are to be polled. This is a network wide parameter. For Portable AutoRoute statistic collections would be… |
| 1.3.6.1.4.1.351.130.5.6.4 | ScalarparSysParmsMaxVDelay | read-only | mandatory | This object specifies the maximum delay for voice connection with VAD enabled in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.5 | ScalarparSysParmsMaxCDelay | read-only | mandatory | This object specifies the maximum delay for ADPCM compressed voice connection with VAD enabled in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.6 | ScalarparSysParmsMaxDDelay | read-only | mandatory | This object specifies the maximum delay for data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.7 | ScalarparSysParmsMaxADelay | read-only | mandatory | This object specifies the maximum delay for ADPCM compressed voice connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.8 | ScalarparSysParmsMaxHsdDelay | read-only | mandatory | This object specifies the maximum delay for High Speed data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.9 | ScalarparSysParmsDeEnable | read-only | mandatory | This object specifies whether DE bit of Frame Relay frames can be modified. DE bit can be modified if the value of this object is True. This is a network wide … |
| 1.3.6.1.4.1.351.130.5.6.10 | ScalarparSysParmsFrStandard | read-only | mandatory | This object specifies whether standard Frame Relay parameters, Be and Bc, are to be used. If the value of this object is True, standard parameters are used. Th… |
| 1.3.6.1.4.1.351.130.5.6.11 | ScalarparSysParmsDrtDelay | read-write | mandatory | This object specifies whether Deroute Delay feature is enabled. If the value of this object is True, the feature is enabled. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.12 | ScalarparSysParmsInvLogAlarmThres | read-only | mandatory | This object specifies the threshold for invalid login attempts before triggering an alarm. If the value of this object is zero, this feature is disabled. This … |
| 1.3.6.1.4.1.351.130.5.6.13 | ScalarparSysParmsMaxCdpVDelay | read-only | mandatory | This object specifies the maximum network delay for CDP to CDP voice connection with VAD enabled in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.14 | ScalarparSysParmsMaxCdpCDelay | read-only | mandatory | This object specifies the maximum network delay for CDP to CDP ADPCM compressed voice connection with VAD enabled in milli-seconds. This is a network wide para… |
| 1.3.6.1.4.1.351.130.5.6.15 | ScalarparSysParmsMaxCdpDDelay | read-only | mandatory | This object specifies the maximum network delay for CDP to CDP data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.16 | ScalarparSysParmsMaxCdpADelay | read-only | mandatory | This object specifies the maximum network delay for CDP to CDP ADPCM compressed voice connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.17 | ScalarparSysParmsMaxCdpHsdDelay | read-only | mandatory | This object specifies the maximum network delay for CDP to CDP High Speed data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.18 | ScalarparSysParmsMaxIpcdpVDelay | read-only | mandatory | This object specifies the maximum local delay for CDP to CDP voice connection with VAD enabled in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.19 | ScalarparSysParmsMaxIpcdpCDelay | read-only | mandatory | This object specifies the maximum local delay for CDP to CDP ADPCM compressed voice connection with VAD enabled in milli-seconds. This is a network wide parame… |
| 1.3.6.1.4.1.351.130.5.6.20 | ScalarparSysParmsMaxIpcdpDDelay | read-only | mandatory | This object specifies the maximum local delay for CDP to CDP data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.21 | ScalarparSysParmsMaxIpcdpADelay | read-only | mandatory | This object specifies the maximum local delay for CDP to CDP ADPCM compressed voice connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.22 | ScalarparSysParmsMaxIpcdpHsdDelay | read-only | mandatory | This object specifies the maximum local delay for CDP to CDP High Speed data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.23 | ScalarparSysParmsMaxIphsdDelay | read-only | mandatory | This object specifies the maximum local delay for High Speed data connection in milli-seconds. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.6.24 | ScalarparSysParmsFpdDeJitter | read-only | mandatory | This object specifies the jitter delay for Fast Pad. This is a network wide parameter. |
| 1.3.6.1.4.1.351.130.5.7 | NodeparNetworkingParms | |||
| 1.3.6.1.4.1.351.130.5.7.1 | ScalarparNetParmCondInitialStgr | read-write | mandatory | This object specifies the initial pause time (in milliseconds) per new node added on addition of node(s) in the network before initiating conditional updates. |
| 1.3.6.1.4.1.351.130.5.7.2 | ScalarparNetParmCondPerNodeInterval | read-write | mandatory | This object specifies the minimum interval (in milliseconds) between sending of conditional updates to any two nodes. |
| 1.3.6.1.4.1.351.130.5.7.3 | ScalarparNetParmCbDelay | read-write | mandatory | This object specifies the minimum interval (in milliseconds) between initiating comm break tests between any two nodes. |
| 1.3.6.1.4.1.351.130.5.7.4 | ScalarparNetParmCbOffset | read-write | mandatory | TBD. |
| 1.3.6.1.4.1.351.130.5.7.5 | ScalarparNetParmMsgTimeout | read-write | mandatory | This object specifies the timeout (in milliseconds) for acknowledgment for control plane message sent to another node. |
| 1.3.6.1.4.1.351.130.5.7.6 | ScalarparNetParmMsgMaxTimeout | read-write | mandatory | This object specifies the maximum number of times a network handler timeout waiting for acknowledgment for control plane message sent to another node reachable… |
| 1.3.6.1.4.1.351.130.5.7.7 | ScalarparNetParmMsgMaxTimeoutSat | read-write | mandatory | This object specifies the maximum number of times a network handler timeout waiting for acknowledgment for control plane message sent to another node reachable… |
| 1.3.6.1.4.1.351.130.5.7.8 | ScalarparNetParmBlindMaxTimeout | read-write | mandatory | This object specifies the maximum number of times a network handler timeout waiting for acknowledgment for control plane blind message sent to another node. |
| 1.3.6.1.4.1.351.130.5.7.9 | ScalarparNetParmCbMaxTimeout | read-write | mandatory | This object specifies the maximum number of times a network handler timeout waiting for acknowledgment for comm break test message sent to another node. |
| 1.3.6.1.4.1.351.130.5.7.10 | ScalarparNetParmCfTestInterval | read-write | mandatory | This object specifies the minimum time interval between the comm fail tests for a trunk. |
| 1.3.6.1.4.1.351.130.5.7.11 | ScalarparNetParmCfTestMultiplier | read-write | mandatory | This object specifies the multiplier for the comm fail test interval for good trunks, that is, trunks not in comm fail. |
| 1.3.6.1.4.1.351.130.5.7.12 | ScalarparNetParmNetwWindowSz | read-write | mandatory | This object specifies the window size for the network handler for messages to any node. That is, the number of messages that the network handler can send simul… |
| 1.3.6.1.4.1.351.130.5.7.13 | ScalarparNetParmNetwLetWait | read-write | mandatory | This object specifies the maximum interval (in milliseconds) network handler waits for the letter (message) from the processes running on its nodes before chec… |
| 1.3.6.1.4.1.351.130.5.7.14 | ScalarparNetParmCfDelay | read-write | mandatory | TBD (in milliseconds). |
| 1.3.6.1.4.1.351.130.5.7.15 | ScalarparNetParmHighTxRate | read-write | mandatory | This object specifies the rate (in fast packets per second) at which the network handler sends control plane message cells to high performance nodes (High perf… |
| 1.3.6.1.4.1.351.130.5.7.16 | ScalarparNetParmLowTxRate | read-write | mandatory | This object specifies the rate (in fast packets per second) at which the network handler sends control plane message cells to low capacity nodes (Low capacity … |
| 1.3.6.1.4.1.351.130.5.7.17 | ScalarparNetParmMaxNodeBlks | read-write | mandatory | This object specifies the maximum number of blocks, of size 256 bytes, that should be queued up for transmission to a node. |
| 1.3.6.1.4.1.351.130.5.7.18 | ScalarparNetParmTopoMsgSegSz | read-write | mandatory | This object specifies the maximum size (in bytes) of the segment into which the topology message, sent during network join, is divided. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AtmAddress | OCTET STRING (SIZE (0 .. 32)) | ||
| IfNsapAddress | OCTET STRING (SIZE ( 20 )) | ||
| NetPrefix | OCTET STRING (SIZE (8 .. 13)) | ||
| RpmNsapAddress | OCTET STRING (SIZE(20)) | ||
| TruthValue | INTEGER { true (1), false (2) } |