DANTHERM-COOLING-MIB
317 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | enterprises |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.46651 | NodedanthermCooling | |||
| 1.3.6.1.4.1.46651.1 | Nodecc3000Trap | Trap From CC300 Controller. Contains TRAP information | ||
| 1.3.6.1.4.1.46651.1 | NodecontrollerCC3000 | |||
| 1.3.6.1.4.1.46651.1.1 | NodesystemStatus | |||
| 1.3.6.1.4.1.46651.1.1.1 | ScalaronBoardTempr | read-only | mandatory | Controller On-Board temperature in Degree Celcius |
| 1.3.6.1.4.1.46651.1.1.2 | ScalarroomTempr | read-only | mandatory | Room Sensor or Zone 1 Sensor temperature in Degree Celcius |
| 1.3.6.1.4.1.46651.1.1.3 | ScalarhotSpotTempr | read-only | mandatory | Hot Spot Sensor or Zone 2 Sensor temperature in Degree Celcius |
| 1.3.6.1.4.1.46651.1.1.4 | Scalaroutdoor1Tempr | read-only | mandatory | Ambient Sensor 1 or Zone 1 Ambient Sensor. temperature in Degree Celcius |
| 1.3.6.1.4.1.46651.1.1.5 | Scalaroutdoor2Tempr | read-only | mandatory | Ambient Sensor 2 or Zone 2 Ambient Sensor. temperature in Degree Celcius |
| 1.3.6.1.4.1.46651.1.1.6 | ScalarshelterTempr | read-only | mandatory | Shelter Temperature. Valid for Single-Zone solution |
| 1.3.6.1.4.1.46651.1.1.7 | ScalaroutdoorCombinedTempr | read-only | mandatory | Cobined minimum Outdoor Temeperature. Valid for Single-Zone solution |
| 1.3.6.1.4.1.46651.1.1.8 | Scalarfan1RPM | read-only | mandatory | Fan 1 Rotation Per Minute |
| 1.3.6.1.4.1.46651.1.1.9 | Scalarfan2RPM | read-only | mandatory | Fan 2 Rotation Per Minute |
| 1.3.6.1.4.1.46651.1.1.10 | Scalarfan1SpeedPercentage | read-only | mandatory | Fan 1 Speed in Percentage of Maximum Speed. Also represents Duty-Cycle of FAn Signal |
| 1.3.6.1.4.1.46651.1.1.11 | Scalarfan2SpeedPercentage | read-only | mandatory | Fan 2 Speed in Percentage of Maximum Speed. Also represents Duty-Cycle of FAn Signal |
| 1.3.6.1.4.1.46651.1.1.12 | Scalardamper1Position | read-only | mandatory | Damper 1 Shutter Open Percentage. 0% - Damper Closed. 100% - Damper completely open |
| 1.3.6.1.4.1.46651.1.1.13 | Scalardamper2Position | read-only | mandatory | Damper 2 Shutter Open Percentage. 0% - Damper Closed. 100% - Damper completely open |
| 1.3.6.1.4.1.46651.1.1.14 | Scalarhumidity | read-only | mandatory | Internal or external humidity in Rh% |
| 1.3.6.1.4.1.46651.1.1.15 | Scalardewpoint | read-only | mandatory | Internal or external DewPoint based on Humidity; in Degree Celcius |
| 1.3.6.1.4.1.46651.1.1.16 | ScalaratmosphericPressure | read-only | mandatory | Atmospheric pressure or Pressure of installed enclosure in KiloPascal |
| 1.3.6.1.4.1.46651.1.1.17 | ScalarflowPressure | read-only | mandatory | Filter flow Pressure in Pascal |
| 1.3.6.1.4.1.46651.1.1.18 | Scalarfan1Status | read-only | mandatory | Fan 1 operation status. 0 - Off; 1 - On -; 2 - Emergency/Boost |
| 1.3.6.1.4.1.46651.1.1.19 | Scalarfan2Status | read-only | mandatory | Fan 2 operation status. 0 - Off; 1 - On -; 2 - Emergency/Boost |
| 1.3.6.1.4.1.46651.1.1.20 | Scalardamper1Status | read-only | mandatory | Damper 1 operation status. 0 - Closed; 1 - Open; 2 - Dynamic or Temperature Compensation; 2 - Emergency/Boost |
| 1.3.6.1.4.1.46651.1.1.21 | Scalardamper2Status | read-only | mandatory | Damper 2 Shutter Open Percentage. 0 - Closed; 1 - Open; 2 - Dynamic or Temperature Compensation; 2 - Emergency/Boost |
| 1.3.6.1.4.1.46651.1.1.22 | Scalaraircond1Status | read-only | mandatory | Airconditioner 1 operation status. 0 - Off; 1 - Restart timeout; 2 - On |
| 1.3.6.1.4.1.46651.1.1.23 | Scalaraircond2Status | read-only | mandatory | Airconditioner 2 operation status. 0 - Off; 1 - Restart timeout; 2 - On |
| 1.3.6.1.4.1.46651.1.1.24 | ScalarheaterStatus | read-only | mandatory | heater operation status. 0 - Off; 1 - On |
| 1.3.6.1.4.1.46651.1.1.25 | Scalarshelter1Status | read-only | mandatory | Shelter Status in Single-Zone mode or Zone 1 Status in Dual-Zone mode respectively. 0 - Inactive or None State 1 - Heating State 2 - Re-Cycling State 3 - Free … |
| 1.3.6.1.4.1.46651.1.1.26 | Scalarshelter2Status | read-only | mandatory | Shelter Status in Dual-Zone mode or Zone 2 Status. 0 - Inactive or None State 1 - Heating State 2 - Re-Cycling State 3 - Free Cooling State 4 - Active or Airco… |
| 1.3.6.1.4.1.46651.1.1.27 | Scalarshelter1Mode | read-only | mandatory | Shelter Run time mode in Single-Zone mode or Zone 1 Status in Dual-Zone mode respectively. 0 - Free Cooling Mode 1 - Standard Mode 2 - Power Save Mode 3 - Air … |
| 1.3.6.1.4.1.46651.1.1.28 | Scalarshelter2Mode | read-only | mandatory | Shelter Run time mode in Dual-Zone mode or Zone 2 Status. 0 - Free Cooling Mode 1 - Standard Mode 2 - Power Save Mode 3 - Air conditioner Mode |
| 1.3.6.1.4.1.46651.1.1.29 | Scalarshelter1Setpoint | read-only | mandatory | Shelter run time Cooling Set point in Single-Zone mode or Zone 1 Status in Dual-Zone mode respectively. Cooling setpoint can be offset by following functions R… |
| 1.3.6.1.4.1.46651.1.1.30 | Scalarshelter2Setpoint | read-only | mandatory | Shelter run time Cooling Set point in Dual-Zone mode or Zone 2 Status. Cooling setpoint can be offset by following functions RH function Night mode Digital inp… |
| 1.3.6.1.4.1.46651.1.1.31 | ScalarerrorStatus | read-only | mandatory | controller internal error status. Binary bit position - alarm drive state: 0 - inactive , 1 - active 0 - voltage low 1 - voltage high 2 - tempr low 3 - tempr l… |
| 1.3.6.1.4.1.46651.1.1.32 | ScalarmaskedErrorStatus | read-only | mandatory | Controller Output Error status. Binary Bit Position - Alarm Drive State: 0 - Inactive , 1 - Active 0 - Voltage Low 1 - Voltage High 2 - Tempr Low 3 - Tempr Lim… |
| 1.3.6.1.4.1.46651.1.1.33 | Scalarvoltage | read-only | mandatory | System Voltage in DC. |
| 1.3.6.1.4.1.46651.1.1.34 | ScalardigitalInputStatus | read-only | mandatory | Controller Alarm Drive Status. Binary Bit Position - Digital Input State: 0 - Inactive , 1 - Active 0 - DIG 1 I/P 1 - DIG 2 I/P 2 - DIG 3 I/P 3 - FILTER GUARD … |
| 1.3.6.1.4.1.46651.1.1.35 | ScalaralarmDriveStatus | read-only | mandatory | Controller Alarm Drive Status. Binary Bit Position - Alarm Drive State: 0 - Inactive , 1 - Active 0 - ALARM 1 1 - ALARM 2 2 - ALARM 3 3 - ALARM 4 4 - ALARM 5 5… |
| 1.3.6.1.4.1.46651.1.1.36 | Scalarfan1OpertdurHour | read-write | mandatory | Fan 1 operation duration - Hour |
| 1.3.6.1.4.1.46651.1.1.37 | Scalarfan1OpertdurMin | read-write | mandatory | Fan 1 operation duration - Minute |
| 1.3.6.1.4.1.46651.1.1.38 | Scalarfan2OpertdurHour | read-write | mandatory | Fan 2 operation duration - Hour |
| 1.3.6.1.4.1.46651.1.1.39 | Scalarfan2OpertdurMin | read-write | mandatory | Fan 2 operation duration - Minute |
| 1.3.6.1.4.1.46651.1.1.40 | Scalaraircon1OpertdurHour | read-write | mandatory | Airconditioner 1 operation duration - Hour |
| 1.3.6.1.4.1.46651.1.1.41 | Scalaraircon1OpertdurMin | read-write | mandatory | Airconditioner 1 operation duration - Minute |
| 1.3.6.1.4.1.46651.1.1.42 | Scalaraircon2OpertdurHour | read-write | mandatory | Airconditioner 2 operation duration - Hour |
| 1.3.6.1.4.1.46651.1.1.43 | Scalaraircon2OpertdurMin | read-write | mandatory | Airconditioner 2 operation duration - Minute |
| 1.3.6.1.4.1.46651.1.1.44 | ScalarheaterOpertdurHour | read-write | mandatory | Heater operation duration - Hour |
| 1.3.6.1.4.1.46651.1.1.45 | ScalarheaterOpertdurMin | read-write | mandatory | Heater operation duration - Minute |
| 1.3.6.1.4.1.46651.1.1.46 | ScalarccSN | read-write | mandatory | CC3000 Controller serial number |
| 1.3.6.1.4.1.46651.1.1.47 | Scalarfanbox1SN | read-write | mandatory | Free cooling FanBox unit 1 serial number |
| 1.3.6.1.4.1.46651.1.1.48 | Scalarfanbox2SN | read-write | mandatory | Free cooling FanBox unit 2 serial number |
| 1.3.6.1.4.1.46651.1.1.49 | Scalaraircond1SN | read-write | mandatory | Aicodnitioner unit 1 serial number |
| 1.3.6.1.4.1.46651.1.1.50 | Scalaraircond2SN | read-write | mandatory | Aicodnitioner unit 2 serial number |
| 1.3.6.1.4.1.46651.1.1.51 | ScalarfwVersion | read-only | mandatory | CC3000 Firmware version |
| 1.3.6.1.4.1.46651.1.2 | NodehighlevelControl | |||
| 1.3.6.1.4.1.46651.1.2.1 | ScalarcoolSetpointZone1 | read-write | mandatory | Cooling Setpoint Zone/Shelter 1 |
| 1.3.6.1.4.1.46651.1.2.2 | ScalarcoolSetpointZone2 | read-write | mandatory | Cooling Setpoint Zone/Shelter 2 |
| 1.3.6.1.4.1.46651.1.2.3 | ScalarheaterSetpoint | read-write | mandatory | Heater Setpoint |
| 1.3.6.1.4.1.46651.1.2.4 | ScalarbackupConfig | read-write | mandatory | Configuration Backup to Internal memory and SD card. 0 - No change, 1 - Backup |
| 1.3.6.1.4.1.46651.1.2.5 | ScalarrestoreConfig | read-write | mandatory | Configuration restore from Internal memory. 0 - No change, 1 - Restore |
| 1.3.6.1.4.1.46651.1.2.6 | ScalarsystemReset | read-write | mandatory | Colling System reset or restart. 0 - No change, 1 - Restart |
| 1.3.6.1.4.1.46651.1.2.7 | Scalaryear | read-write | mandatory | Calender - Year |
| 1.3.6.1.4.1.46651.1.2.8 | Scalarmonth | read-write | mandatory | Calender - Month |
| 1.3.6.1.4.1.46651.1.2.9 | Scalardate | read-write | mandatory | Calender - Date |
| 1.3.6.1.4.1.46651.1.2.10 | Scalarhour | read-write | mandatory | Clock - Hour |
| 1.3.6.1.4.1.46651.1.2.11 | Scalarminute | read-write | mandatory | Clock - Minute |
| 1.3.6.1.4.1.46651.1.3 | Nodefan1Config | |||
| 1.3.6.1.4.1.46651.1.3.1 | ScalarsaveReloadConff1 | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.3.2 | ScalaroffTemprf1 | read-write | mandatory | Fan OFF temperature |
| 1.3.6.1.4.1.46651.1.3.3 | ScalaridleOnTemprf1 | read-write | mandatory | Fan Idle Speed On temperature |
| 1.3.6.1.4.1.46651.1.3.4 | ScalaridleEntryTemprf1 | read-write | mandatory | Idle entry temperature |
| 1.3.6.1.4.1.46651.1.3.5 | ScalarmidPoint1Temprf1 | read-write | mandatory | Mid point 1 entry temperature |
| 1.3.6.1.4.1.46651.1.3.6 | ScalarsetPointTemprf1 | read-write | mandatory | Set Point temperature |
| 1.3.6.1.4.1.46651.1.3.7 | ScalarmidPoint2Temprf1 | read-write | mandatory | Mid point 2 entry temperature |
| 1.3.6.1.4.1.46651.1.3.8 | ScalarhighSpeedTemprf1 | read-write | mandatory | high Speed entry temperature |
| 1.3.6.1.4.1.46651.1.3.9 | ScalarextendHighSpeedEntryTemprf1 | read-write | mandatory | Extended high Speed entry temperature |
| 1.3.6.1.4.1.46651.1.3.10 | ScalarextendHighSpeedExitTemprf1 | read-write | mandatory | Extended high Speed exit temperature |
| 1.3.6.1.4.1.46651.1.3.11 | ScalarboostEntryTemprf1 | read-write | mandatory | Boost Speed entry temperature |
| 1.3.6.1.4.1.46651.1.3.12 | ScalarboostExitTemprf1 | read-write | mandatory | Boost Speed entry temperature |
| 1.3.6.1.4.1.46651.1.3.13 | ScalaridleRPMf1 | read-write | mandatory | Idle speed RPM |
| 1.3.6.1.4.1.46651.1.3.14 | ScalarmidPointRPMf1 | read-write | mandatory | Midpoint Speed RPM |
| 1.3.6.1.4.1.46651.1.3.15 | ScalarhighSpeedRPMf1 | read-write | mandatory | high Speed RPM |
| 1.3.6.1.4.1.46651.1.3.16 | ScalarextendHighSpeedRPMf1 | read-write | mandatory | Extended high Speed RPM |
| 1.3.6.1.4.1.46651.1.3.17 | ScalaridleDutyCyclef1 | read-write | mandatory | Idle Speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.3.18 | ScalarmidDutyCyclef1 | read-write | mandatory | Midpoint speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.3.19 | ScalarhighSpeedDutyCyclef1 | read-write | mandatory | high speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.3.20 | ScalarextendHighSpeedDutyCyclef1 | read-write | mandatory | Extended high speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.3.21 | ScalarboostDutyCyclef1 | read-write | mandatory | Boost speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.3.22 | ScalardeadBandRPMf1 | read-write | mandatory | Dead band RPM |
| 1.3.6.1.4.1.46651.1.3.23 | ScalaroverrideDigi1f1 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.3.24 | ScalaroverrideDigi2f1 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.3.25 | ScalaroverrideDigi3f1 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.3.26 | ScalaroverrideSensorfailf1 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.3.27 | ScalarsensorSelectf1 | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.3.28 | ScalartachoPulseperrotationf1 | read-write | mandatory | Number of Tacho pulses per cycle rotation for given fan |
| 1.3.6.1.4.1.46651.1.3.29 | ScalarclosedLoopenablef1 | read-write | mandatory | Closed Loop control enable or disable for given Fan. 0 - Enable. 1 - Disable |
| 1.3.6.1.4.1.46651.1.3.30 | ScalarcontrolTypef1 | read-write | mandatory | 0 - 0-10V DC control. 1 - PWM control |
| 1.3.6.1.4.1.46651.1.3.31 | Scalarenablef1 | read-write | mandatory | 0 - Disable Fan control. 1 - Enabel fan control |
| 1.3.6.1.4.1.46651.1.4 | Nodefan2Config | |||
| 1.3.6.1.4.1.46651.1.4.1 | ScalarsaveReloadConff2 | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.4.2 | ScalaroffTemprf2 | read-write | mandatory | Fan OFF temperature |
| 1.3.6.1.4.1.46651.1.4.3 | ScalaridleOnTemprf2 | read-write | mandatory | Fan Idle Speed On temperature |
| 1.3.6.1.4.1.46651.1.4.4 | ScalaridleEntryTemprf2 | read-write | mandatory | Idle entry temperature |
| 1.3.6.1.4.1.46651.1.4.5 | ScalarmidPoint1Temprf2 | read-write | mandatory | Mid point 1 entry temperature |
| 1.3.6.1.4.1.46651.1.4.6 | ScalarsetPointTemprf2 | read-write | mandatory | Set Point temperature |
| 1.3.6.1.4.1.46651.1.4.7 | ScalarmidPoint2Temprf2 | read-write | mandatory | Mid point 2 entry temperature |
| 1.3.6.1.4.1.46651.1.4.8 | ScalarhighSpeedTemprf2 | read-write | mandatory | high Speed entry temperature |
| 1.3.6.1.4.1.46651.1.4.9 | ScalarextendHighSpeedEntryTemprf2 | read-write | mandatory | Extended high Speed entry temperature |
| 1.3.6.1.4.1.46651.1.4.10 | ScalarextendHighSpeedExitTemprf2 | read-write | mandatory | Extended high Speed exit temperature |
| 1.3.6.1.4.1.46651.1.4.11 | ScalarboostEntryTemprf2 | read-write | mandatory | Boost Speed entry temperature |
| 1.3.6.1.4.1.46651.1.4.12 | ScalarboostExitTemprf2 | read-write | mandatory | Boost Speed entry temperature |
| 1.3.6.1.4.1.46651.1.4.13 | ScalaridleRPMf2 | read-write | mandatory | Idle speed RPM |
| 1.3.6.1.4.1.46651.1.4.14 | ScalarmidPointRPMf2 | read-write | mandatory | Midpoint Speed RPM |
| 1.3.6.1.4.1.46651.1.4.15 | ScalarhighSpeedRPMf2 | read-write | mandatory | high Speed RPM |
| 1.3.6.1.4.1.46651.1.4.16 | ScalarextendHighSpeedRPMf2 | read-write | mandatory | Extended high Speed RPM |
| 1.3.6.1.4.1.46651.1.4.17 | ScalaridleDutyCyclef2 | read-write | mandatory | Idle Speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.4.18 | ScalarmidDutyCyclef2 | read-write | mandatory | Midpoint speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.4.19 | ScalarhighSpeedDutyCyclef2 | read-write | mandatory | high speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.4.20 | ScalarextendHighSpeedDutyCyclef2 | read-write | mandatory | Extended high speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.4.21 | ScalarboostDutyCyclef2 | read-write | mandatory | Boost speed Duty Cycle |
| 1.3.6.1.4.1.46651.1.4.22 | ScalardeadBandRPMf2 | read-write | mandatory | Dead band RPM |
| 1.3.6.1.4.1.46651.1.4.23 | ScalaroverrideDigi1f2 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.4.24 | ScalaroverrideDigi2f2 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.4.25 | ScalaroverrideDigi3f2 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.4.26 | ScalaroverrideSensorfailf2 | read-write | mandatory | 0-100 - Fan Speed in Duty cycle. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.4.27 | ScalarsensorSelectf2 | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.4.28 | ScalartachoPulseperrotationf2 | read-write | mandatory | Number of Tacho pulses per cycle rotation for given fan |
| 1.3.6.1.4.1.46651.1.4.29 | ScalarclosedLoopenablef2 | read-write | mandatory | Closed Loop control enable or disable for given Fan. 0 - Enable. 1 - Disable |
| 1.3.6.1.4.1.46651.1.4.30 | ScalarcontrolTypef2 | read-write | mandatory | 0 - 0-10V DC control. 1 - PWM control |
| 1.3.6.1.4.1.46651.1.4.31 | Scalarenablef2 | read-write | mandatory | 0 - Disable Fan control. 1 - Enabel fan control |
| 1.3.6.1.4.1.46651.1.5 | Nodedamper1Config | |||
| 1.3.6.1.4.1.46651.1.5.1 | ScalarsaveReloadConfd1 | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.5.2 | ScalarlowercloseTemprd1 | read-write | mandatory | Damper lower closing temperature |
| 1.3.6.1.4.1.46651.1.5.3 | ScalarsetPointd1 | read-write | mandatory | Damper opening temperature |
| 1.3.6.1.4.1.46651.1.5.4 | ScalarupperOpentempd1 | read-write | mandatory | Damper upper opening temperature |
| 1.3.6.1.4.1.46651.1.5.5 | ScalarupperClosetempd1 | read-write | mandatory | Damper upper closing temperature |
| 1.3.6.1.4.1.46651.1.5.6 | ScalaremgncyClosetempd1 | read-write | mandatory | Damper emergency closing temperature |
| 1.3.6.1.4.1.46651.1.5.7 | Scalaremgncyopentempd1 | read-write | mandatory | Damper emergency open temperature |
| 1.3.6.1.4.1.46651.1.5.8 | ScalaroverrideDigi1d1 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.5.9 | ScalaroverrideDigi2d1 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.5.10 | ScalaroverrideDigi3d1 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.5.11 | ScalaroverrideSensorFaild1 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.5.12 | ScalarsensSelectd1 | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.5.13 | ScalarrunDurationd1 | read-write | mandatory | Damper Run time in minutes |
| 1.3.6.1.4.1.46651.1.5.14 | Scalarenabled1 | read-write | mandatory | 0 - Disable. 1 - ONOFF. 2 - Dynamic |
| 1.3.6.1.4.1.46651.1.6 | Nodedamper2Config | |||
| 1.3.6.1.4.1.46651.1.6.1 | ScalarsaveReloadConfd2 | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.6.2 | ScalarlowercloseTemprd2 | read-write | mandatory | Damper lower closing temperature |
| 1.3.6.1.4.1.46651.1.6.3 | ScalarsetPointd2 | read-write | mandatory | Damper opening temperature |
| 1.3.6.1.4.1.46651.1.6.4 | ScalarupperOpentempd2 | read-write | mandatory | Damper upper opening temperature |
| 1.3.6.1.4.1.46651.1.6.5 | ScalarupperClosetempd2 | read-write | mandatory | Damper upper closing temperature |
| 1.3.6.1.4.1.46651.1.6.6 | ScalaremgncyClosetempd2 | read-write | mandatory | Damper emergency closing temperature |
| 1.3.6.1.4.1.46651.1.6.7 | Scalaremgncyopentempd2 | read-write | mandatory | Damper emergency open temperature |
| 1.3.6.1.4.1.46651.1.6.8 | ScalaroverrideDigi1d2 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.6.9 | ScalaroverrideDigi2d2 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.6.10 | ScalaroverrideDigi3d2 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.6.11 | ScalaroverrideSensorFaild2 | read-write | mandatory | 0 - Damper close. 1 - Damper open. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.6.12 | ScalarsensSelectd2 | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.6.13 | ScalarrunDurationd2 | read-write | mandatory | Damper Run time in minutes |
| 1.3.6.1.4.1.46651.1.6.14 | Scalarenabled2 | read-write | mandatory | 0 - Disable. 1 - ONOFF. 2 - Dynamic |
| 1.3.6.1.4.1.46651.1.7 | Nodeaircon1Config | |||
| 1.3.6.1.4.1.46651.1.7.1 | ScalarsaveReloadConfac1 | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.7.2 | ScalaroNTemprac1 | read-write | mandatory | Air Conditioner ON temperature |
| 1.3.6.1.4.1.46651.1.7.3 | ScalaroFFTemprac1 | read-write | mandatory | Air Conditioner OFF temperature |
| 1.3.6.1.4.1.46651.1.7.4 | ScalaroverrideDigi1ac1 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.7.5 | ScalaroverrideDigi2ac1 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.7.6 | ScalaroverrideDigi3ac1 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride |
| 1.3.6.1.4.1.46651.1.7.7 | ScalaroverrideSensorFailac1 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride |
| 1.3.6.1.4.1.46651.1.7.8 | ScalarsensSelectac1 | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.7.9 | ScalarminimumRunDurationac1 | read-write | mandatory | Minimum AC Run time in seconds |
| 1.3.6.1.4.1.46651.1.7.10 | ScalarrestartTimeoutac1 | read-write | mandatory | Restart timer in seconds |
| 1.3.6.1.4.1.46651.1.7.11 | Scalarenableac1 | read-write | mandatory | 0 - Disable. 1 - Enable. |
| 1.3.6.1.4.1.46651.1.8 | Nodeaircon2Config | |||
| 1.3.6.1.4.1.46651.1.8.1 | ScalarsaveReloadConfac2 | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.8.2 | ScalaronTemprac2 | read-write | mandatory | Air Conditioner ON temperature |
| 1.3.6.1.4.1.46651.1.8.3 | ScalaroffTemprac2 | read-write | mandatory | Air Conditioner OFF temperature |
| 1.3.6.1.4.1.46651.1.8.4 | ScalaroverrideDigi1ac2 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.8.5 | ScalaroverrideDigi2ac2 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.8.6 | ScalaroverrideDigi3ac2 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride |
| 1.3.6.1.4.1.46651.1.8.7 | ScalaroverrideSensorFailac2 | read-write | mandatory | 0 - AC OFF. 1 - AC ON. 120 - No action on Over ride |
| 1.3.6.1.4.1.46651.1.8.8 | ScalarsensSelectac2 | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.8.9 | ScalarminimumRunDurationac2 | read-write | mandatory | Minimum AC Run time in seconds |
| 1.3.6.1.4.1.46651.1.8.10 | ScalarrestartTimeoutac2 | read-write | mandatory | Restart timer in seconds |
| 1.3.6.1.4.1.46651.1.8.11 | Scalarenableac2 | read-write | mandatory | 0 - Disable. 1 - Enable. |
| 1.3.6.1.4.1.46651.1.9 | NodeheaterConfig | |||
| 1.3.6.1.4.1.46651.1.9.1 | ScalarsaveReloadConfhtr | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.9.2 | ScalaronTemprhtr | read-write | mandatory | Heater ON temperature |
| 1.3.6.1.4.1.46651.1.9.3 | ScalaroffTemprhtr | read-write | mandatory | Heater OFF temperature |
| 1.3.6.1.4.1.46651.1.9.4 | ScalaroverrideDigi1htr | read-write | mandatory | 0 - Heat OFF. 1 - Heat ON. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.9.5 | ScalaroverrideDigi2htr | read-write | mandatory | 0 - Heat OFF. 1 - Heat ON. 120 - No action on Over ride. |
| 1.3.6.1.4.1.46651.1.9.6 | ScalaroverrideDigi3htr | read-write | mandatory | 0 - Heat OFF. 1 - Heat ON. 120 - No action on Over ride |
| 1.3.6.1.4.1.46651.1.9.7 | ScalaroverrideSensorFailhtr | read-write | mandatory | 0 - Heat OFF. 1 - Heat ON. 120 - No action on Over ride |
| 1.3.6.1.4.1.46651.1.9.8 | ScalarsensSelecthtr | read-write | mandatory | 0 - Onboard sensor. 1 - Room Sensor. 2 - Hotspot sensor. 3 - Ambient 2 sensor. 4 - Ambient 1 sensor. 5 - Shelter temperature |
| 1.3.6.1.4.1.46651.1.9.9 | Scalarenablehtr | read-write | mandatory | 0 - Disable. 1 - Enable. |
| 1.3.6.1.4.1.46651.1.10 | NodehumidityConfig | |||
| 1.3.6.1.4.1.46651.1.10.1 | ScalarsaveReloadConfhum | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.10.2 | ScalarrhEntryhum | read-write | mandatory | Humidity function entry value |
| 1.3.6.1.4.1.46651.1.10.3 | ScalarrhExithum | read-write | mandatory | Humidity function exit value |
| 1.3.6.1.4.1.46651.1.10.4 | Scalarcoolingmodehum | read-write | mandatory | 0 - Freecooling. 1 - Standard. 2 - Power save. 3 - Aircon. |
| 1.3.6.1.4.1.46651.1.10.5 | Scalartemprsetpoffsethum | read-write | mandatory | Cooling setpoint offset |
| 1.3.6.1.4.1.46651.1.10.6 | ScalarrhSensPositionhum | read-write | mandatory | 0 - Indoor. 1 - Outdoor |
| 1.3.6.1.4.1.46651.1.10.7 | Scalarenablehum | read-write | mandatory | 0 - Disable. 1 - Enable. |
| 1.3.6.1.4.1.46651.1.11 | NodesystemConfig | |||
| 1.3.6.1.4.1.46651.1.11.1 | ScalarsaveReloadConfsysc | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.11.2 | ScalarvdcLowEntrysys | read-write | mandatory | Low voltage shut down entry |
| 1.3.6.1.4.1.46651.1.11.3 | ScalarvdcLowExitsys | read-write | mandatory | Low voltage shut down exit |
| 1.3.6.1.4.1.46651.1.11.4 | ScalarvdcHighEntrysys | read-write | mandatory | High voltage shut down entry |
| 1.3.6.1.4.1.46651.1.11.5 | ScalarvdcHighExitsys | read-write | mandatory | High voltage shut down exit |
| 1.3.6.1.4.1.46651.1.11.6 | ScalartemprLowlimitsys | read-write | mandatory | Low temperature alarm limit |
| 1.3.6.1.4.1.46651.1.11.7 | ScalartemprHighlimit1sys | read-write | mandatory | High temperature alarm limit 1 |
| 1.3.6.1.4.1.46651.1.11.8 | ScalartemprHighlimit2sys | read-write | mandatory | High temperature alarm limit 2 |
| 1.3.6.1.4.1.46651.1.11.9 | ScalartemprHighlimit3sys | read-write | mandatory | High temperature alarm limit 3 |
| 1.3.6.1.4.1.46651.1.11.10 | Scalartemprlimithyssys | read-write | mandatory | Temperature alarm limit hysteresis |
| 1.3.6.1.4.1.46651.1.11.11 | ScalarrhLowlimitsys | read-write | mandatory | Humidity alarm low limit %RH |
| 1.3.6.1.4.1.46651.1.11.12 | ScalarrhHighlimitsys | read-write | mandatory | Humidity alarm High limit %RH |
| 1.3.6.1.4.1.46651.1.11.13 | Scalarflowpresslimit1sys | read-write | mandatory | Flow pressure limit 1 Pa |
| 1.3.6.1.4.1.46651.1.11.14 | Scalarflowpresslimit2sys | read-write | mandatory | Flow pressure limit 2 Pa |
| 1.3.6.1.4.1.46651.1.11.15 | Scalarflowpresshyssys | read-write | mandatory | Flow pressure limit hysteresis Pa |
| 1.3.6.1.4.1.46651.1.11.16 | Scalarcoolingzonessys | read-write | mandatory | 1 - One cooling zone, 2 - Two cooling zones |
| 1.3.6.1.4.1.46651.1.11.17 | ScalarcoolingModesys | read-write | mandatory | 0 - FC, 1 - Std, 2 - Ps, 3 - Acon |
| 1.3.6.1.4.1.46651.1.11.18 | ScalarnegCoolingDeltaOverridesys | read-write | mandatory | 0 - Disable, 1 - Enable |
| 1.3.6.1.4.1.46651.1.11.19 | ScalarnegCoolingDeltaHyssys | read-write | mandatory | Negative cooling delta hysteresis |
| 1.3.6.1.4.1.46651.1.11.20 | ScalarcoolingDeltatempsys | read-write | mandatory | Cooling delta temperature |
| 1.3.6.1.4.1.46651.1.11.21 | ScalarshelterTemprsys | read-write | mandatory | 0 - RA, 1 - HS, 2 - Both |
| 1.3.6.1.4.1.46651.1.11.22 | Scalaracleadlagsys | read-write | mandatory | 0 - Disable, 1 - Enable |
| 1.3.6.1.4.1.46651.1.11.23 | ScalarcoolingModeXzonesys | read-write | mandatory | 0 - FC, 1 - Std, 2 - Ps, 3 - Acon |
| 1.3.6.1.4.1.46651.1.11.24 | ScalarnegCoolingDeltaOverrideXzonesys | read-write | mandatory | 0 - Disable, 1 - Enable |
| 1.3.6.1.4.1.46651.1.11.25 | ScalarnegCoolingDeltaHysXzonesys | read-write | mandatory | Negative cooling delta hysteresis |
| 1.3.6.1.4.1.46651.1.11.26 | ScalarcoolingDeltatempXzonesys | read-write | mandatory | Cooling delta temperature |
| 1.3.6.1.4.1.46651.1.11.27 | Scalarfan1Zonesys | read-write | mandatory | 1 - Fan 1 for Zone 1, 2 - Fan 1 for zone 2 |
| 1.3.6.1.4.1.46651.1.11.28 | Scalarfan2Zonesys | read-write | mandatory | 1 - Fan 2 for Zone 1, 2 - Fan 2 for zone 2 |
| 1.3.6.1.4.1.46651.1.11.29 | Scalarac1Zonesys | read-write | mandatory | 1 - AC 1 for Zone 1, 2 - AC 1 for zone 2 |
| 1.3.6.1.4.1.46651.1.11.30 | Scalarac2Zonesys | read-write | mandatory | 1 - AC 2 for Zone 1, 2 - AC 2 for zone 2 |
| 1.3.6.1.4.1.46651.1.11.31 | Scalardamper1Zonesys | read-write | mandatory | 1 - Damper 1 for Zone 1, 2 - Damper 1 for zone 2 |
| 1.3.6.1.4.1.46651.1.11.32 | Scalardamper2Zonesys | read-write | mandatory | 1 - Damper 2 for Zone 1, 2 - Damper 2 for zone 2 |
| 1.3.6.1.4.1.46651.1.11.33 | ScalarheaterZonesys | read-write | mandatory | 1 - Heater for Zone 1, 2 - Heater for zone 2 |
| 1.3.6.1.4.1.46651.1.11.34 | ScalarstatusLogsys | read-write | mandatory | 0 - Disable, 1 - Enable |
| 1.3.6.1.4.1.46651.1.11.35 | Scalarlogintervalsys | read-write | mandatory | Log interval in minutes |
| 1.3.6.1.4.1.46651.1.11.36 | Scalaralarm1NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.37 | Scalaralarm2NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.38 | Scalaralarm3NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.39 | Scalaralarm4NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.40 | Scalaralarm5NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.41 | Scalaralarm6NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.42 | Scalaralarm7NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.43 | Scalaralarm8NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.44 | Scalaralarm9NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.45 | Scalaralarm10NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.46 | Scalaralarm1Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.47 | Scalaralarm2Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.48 | Scalaralarm3Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.49 | Scalaralarm4Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.50 | Scalaralarm5Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.51 | Scalaralarm6Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.52 | Scalaralarm7Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.53 | Scalaralarm8Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.54 | Scalaralarm9Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.55 | Scalaralarm10Delaysys | read-write | mandatory | Alarm output delay in seconds |
| 1.3.6.1.4.1.46651.1.11.56 | Scalarac1NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.57 | Scalarac2NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.58 | Scalardig1NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.59 | Scalardig2NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.60 | Scalardig3NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.61 | Scalardig2funcoverridesys | read-write | mandatory | 0 - Override, 1 - setpoint offset, 2 - mode X |
| 1.3.6.1.4.1.46651.1.11.62 | Scalardig3funcoverridesys | read-write | mandatory | 0 - Override, 1 - setpoint offset, 2 - mode X |
| 1.3.6.1.4.1.46651.1.11.63 | Scalardig2offsetsys | read-write | mandatory | Cooling setpoint offset |
| 1.3.6.1.4.1.46651.1.11.64 | Scalardig3offsetsys | read-write | mandatory | Cooling setpoint offset |
| 1.3.6.1.4.1.46651.1.11.65 | Scalardig2trigModesys | read-write | mandatory | 0 - FC, 1 - Std, 2 - Ps, 3 - Acon |
| 1.3.6.1.4.1.46651.1.11.66 | Scalardig3TrigModesys | read-write | mandatory | 0 - FC, 1 - Std, 2 - Ps, 3 - Acon |
| 1.3.6.1.4.1.46651.1.11.67 | ScalarfilterGuard1NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.68 | ScalarfilterGuard2NONCsys | read-write | mandatory | 0 - NO, 1 - NC |
| 1.3.6.1.4.1.46651.1.11.69 | ScalartemprUnitsCFsys | read-write | mandatory | 0 - Celcius, 1 - Fahrenheit |
| 1.3.6.1.4.1.46651.1.11.70 | ScalarlanguageEnglishsys | read-write | mandatory | 0 - Disable, 1 - Enable |
| 1.3.6.1.4.1.46651.1.12 | NodealarmConfig | |||
| 1.3.6.1.4.1.46651.1.12.1 | ScalarsaveReloadConfAlm | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Alarm Mapping reloaded |
| 1.3.6.1.4.1.46651.1.12.2 | Scalaralarm1mask | read-write | mandatory | Alarm drive 1 Mask [Can have multiple Alarm Errors]. Bit Position - Value - Alarm Drive State: 0 - Unselect, 1 - Select 1 - 1 - Voltage Low 2 - 2 - Voltage Hig… |
| 1.3.6.1.4.1.46651.1.12.3 | Scalaralarm2mask | read-write | mandatory | Alarm drive 2 Mask [Can have multiple Alarm Errors]. Bit Position - Value - Alarm Drive State: 0 - Unselect, 1 - Select 1 - 1 - Voltage Low 2 - 2 - Voltage Hig… |
| 1.3.6.1.4.1.46651.1.12.4 | Scalaralarm3mask | read-write | mandatory | Alarm drive 3 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.5 | Scalaralarm4mask | read-write | mandatory | Alarm drive 4 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.6 | Scalaralarm5mask | read-write | mandatory | Alarm drive 5 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.7 | Scalaralarm6mask | read-write | mandatory | Alarm drive 6 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.8 | Scalaralarm7mask | read-write | mandatory | Alarm drive 7 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.9 | Scalaralarm8mask | read-write | mandatory | Alarm drive 8 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.10 | Scalaralarm9mask | read-write | mandatory | Alarm drive 9 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Tem… |
| 1.3.6.1.4.1.46651.1.12.11 | Scalaralarm10mask | read-write | mandatory | Alarm drive 10 Select [Single Alarm Error]. Bit Position - Alarm Drive State: 0 - Unselect, 1-25 - Select 1 - Voltage Low 2 - Voltage High 3 - Tempr Low 4 - Te… |
| 1.3.6.1.4.1.46651.1.13 | NodenightModeConfig | |||
| 1.3.6.1.4.1.46651.1.13.1 | ScalarsaveReloadConfNm | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.13.2 | ScalarstarttimeHournm | read-write | mandatory | Night Mode Start time hour |
| 1.3.6.1.4.1.46651.1.13.3 | ScalarstartTimeMinutesnm | read-write | mandatory | Night Mode Start time minutes |
| 1.3.6.1.4.1.46651.1.13.4 | ScalarendTimeHournm | read-write | mandatory | Night Mode End time hour |
| 1.3.6.1.4.1.46651.1.13.5 | ScalarendTimeMinutesnm | read-write | mandatory | Night Mode End time minutes |
| 1.3.6.1.4.1.46651.1.13.6 | ScalarfanMaxRPMnm | read-write | mandatory | % of max fan speed |
| 1.3.6.1.4.1.46651.1.13.7 | ScalarsetPointOffsetnm | read-write | mandatory | Cooling setpoint offset |
| 1.3.6.1.4.1.46651.1.13.8 | ScalarcoolingModenm | read-write | mandatory | 0 - Freecooling. 1 - Standard. 2 - Power save. 3 - Aircon. |
| 1.3.6.1.4.1.46651.1.13.9 | Scalarenablenm | read-write | mandatory | 0 - Disable. 1 - Enable. |
| 1.3.6.1.4.1.46651.1.14 | NodenetworkConfig | |||
| 1.3.6.1.4.1.46651.1.14.1 | ScalarsaveReloadConfNW | read-write | mandatory | 0 - Discard modifications, 1 - Save Modifications. Configuration reloaded |
| 1.3.6.1.4.1.46651.1.14.2 | Scalardhcpenable | read-write | mandatory | 0 - Static IP, 1 - Dynamic IP |
| 1.3.6.1.4.1.46651.1.14.3 | Scalaripaddr | read-write | mandatory | System IP Address |
| 1.3.6.1.4.1.46651.1.14.4 | Scalarsubnetmask | read-write | mandatory | Sub-net Mask |
| 1.3.6.1.4.1.46651.1.14.5 | ScalargatewayIPaddr | read-write | mandatory | Default Gateway IP Address |
| 1.3.6.1.4.1.46651.1.14.6 | ScalarntpIPaddr | read-write | mandatory | DNS IP Address |
| 1.3.6.1.4.1.46651.1.14.7 | ScalarsnmpPort | read-write | mandatory | SNMP Agent Port |
| 1.3.6.1.4.1.46651.1.14.8 | ScalartrapServer1IPaddr | read-write | mandatory | SNMP TRAP manager 1 IP address |
| 1.3.6.1.4.1.46651.1.14.9 | ScalartrapServer1port | read-write | mandatory | SNMP TRAP manager 1 Port Number |
| 1.3.6.1.4.1.46651.1.14.10 | ScalartrapServer2IPaddr | read-write | mandatory | SNMP TRAP manager 2 IP address |
| 1.3.6.1.4.1.46651.1.14.11 | ScalartrapServer2port | read-write | mandatory | SNMP TRAP manager 2 Port Number |
| 1.3.6.1.4.1.46651.1.14.12 | ScalartrapServer3IPaddr | read-write | mandatory | SNMP TRAP manager 3 IP address |
| 1.3.6.1.4.1.46651.1.14.13 | ScalartrapServer3port | read-write | mandatory | SNMP TRAP manager 3 Port Number |
| 1.3.6.1.4.1.46651.1.14.14 | ScalarsnmpCommunity | read-write | mandatory | SNMP Read/write Community string |
| 1.3.6.1.4.1.46651.1.14.15 | ScalarhostName | read-write | mandatory | System Netwrok Host name |
| 1.3.6.1.4.1.46651.1.15 | NodetrapError | |||
| 1.3.6.1.4.1.46651.1.15.1 | ScalarerrorNumber | not-accessible | mandatory | Error Number corresponding to CC3000 controller Error. |
| 1.3.6.1.4.1.46651.1.15.2 | Scalarstatus | not-accessible | mandatory | Error Status Active/SET or Inactive/CLEAR. |
| 1.3.6.1.4.1.46651.1.15.3 | Scalarvalue | not-accessible | mandatory | Value Corresponding to Error Occurance Instance. |
| 1.3.6.1.4.1.46651.1.15.4 | Scalarinfo | not-accessible | mandatory | Description of Current Error. |