DEC-ELAN-MIB
754 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.36 | Nodedec | |||
| 1.3.6.1.4.1.36.2 | Nodeema | |||
| 1.3.6.1.4.1.36.2.15 | Nodesysobjid | |||
| 1.3.6.1.4.1.36.2.15.3 | Nodebridges | |||
| 1.3.6.1.4.1.36.2.15.3.3 | Nodegigaswitch | |||
| 1.3.6.1.4.1.36.2.15.3.3.1 | ScalarminimumGIGAswitchMIBVersionSupported | read-only | mandatory | When new GIGAswitch MIBs are released to the public, they will be given new version numbers. The implementation strategy allows multiple versions to be support… |
| 1.3.6.1.4.1.36.2.15.3.3.2 | ScalarmaximumGIGAswitchMIBVersionSupported | read-only | mandatory | When new GIGAswitch MIBs are released to the public, they will be given new version numbers. The implementation strategy allows multiple versions to be support… |
| 1.3.6.1.4.1.36.2.15.3.3.3 | Nodegigaversion1 | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1 | NodegigaBox | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1 | NodeclockCard | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1.1 | ScalarmgmtMemoryAvail | read-only | mandatory | The number of unused bytes of management memory available on the clock card. The management memory is used for storing management parameters. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1.2 | ScalarmgmtMemoryAction | read-write | mandatory | This object, when read, returns a value of other(1) unless it is in the middle of rewriting the management memory. At such times, it will return rewriting(3). … |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1.3 | TablemgmtMemoryTable | not-accessible | mandatory | The table for managing management memory. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1.3.1 | RowmgmtMemoryEntry | not-accessible | mandatory | A record of management memory. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1.3.1.1 | ColumnmgmtMemoryIndex | read-only | mandatory | Index of 80 byte binary records |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.1.3.1.2 | ColumnmgmtMemoryData | read-write | mandatory | SNMP object mgmtMemoryData allows the user to read management memory and, with certain restrictions, to write it as well. In particular, this object allows the… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2 | Nodepsc | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.1 | ScalarpscStatus | read-only | mandatory | The status of the Power System Controller (PSC). |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.2 | ScalarpscFwRev | read-only | mandatory | The firmware revision of the Power System Controller (PSC). |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.3 | ScalarpscHwRev | read-only | mandatory | The hardware revision of the Power System Controller (PSC). |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.4 | ScalarkeyswitchPosition | read-only | mandatory | Indicates the position of the keyswitch. The keyswitch position determines the type of access allowed to network management and to out-of-band management. For … |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.5 | ScalarpscFwImageStatus | read-only | mandatory | The status of the PSC firmware image. If the value of this object is downloadRequired(2), the manager should download a new firmware image to the PSC. This can… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.6 | ScalarpscBackplaneStatus | read-only | mandatory | Status of the GIGAswitch backplane. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.7 | ScalarcabinetTemperature | read-only | mandatory | The cabinet temperature. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.2.8 | ScalartemperatureWarning | read-write | mandatory | The value of this variable determines how the SCP responds to a condition of too high or too low cabinet temperature, or both both fans inoperative. If the val… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3 | NodepowerSupply | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3.1 | ScalarrightPowerStatus | read-only | mandatory | The status of the right power unit. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3.2 | ScalarrightPowerInputSource | read-only | mandatory | The input source of the right power unit. A value of ACline(1) is returned if the power supply is connected to an AC line. A value of DC48V(2) is returned if t… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3.3 | ScalarrightPowerOutputPower | read-only | mandatory | Output power of right power unit, in watts. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3.4 | ScalarleftPowerStatus | read-only | mandatory | The status of the left power unit. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3.5 | ScalarleftPowerInputSource | read-only | mandatory | The input source of the left power unit. A value of ACline(1) is returned if the power supply is connected to an AC line. A value of DC48V(2) is returned if th… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.3.6 | ScalarleftPowerOutputPower | read-only | mandatory | Output power of left power unit, in watts. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4 | Nodeslot | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.1 | ScalarslotNumber | read-only | mandatory | The number of slots in the box. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.2 | ScalarscpSlot | read-only | mandatory | Identifies the slot the Switch Control Processor (SCP) occupies. A value of 0 will be returned if an SCP has not been chosen. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3 | TableslotTable | not-accessible | mandatory | Describes the current configuration of the box. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1 | RowslotEntry | not-accessible | mandatory | The description and status of the card plugged into the slot. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.1 | ColumnslotIndex | read-only | mandatory | The slot number. Varies from 1 to slotNumber. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.2 | ColumnslotCardStatus | read-write | mandatory | The status of the card. If the value is read as notPresent(1), then the entire entry should be considered invalid. Writing a value of powerDown(2) will cause t… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.3 | ColumnslotCardType | read-only | mandatory | The type of the Card. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.4 | ColumnslotCardHwRev | read-only | mandatory | The Hardware revision number of the card. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.5 | ColumnslotCardFwRev | read-only | mandatory | The Firmware revision number of the card. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.4 | TablehostSlotTable | not-accessible | mandatory | Describes the current IP address and community string of any modules which are hosted in the switch (eg GS2000). |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.4.1 | RowhostSlotEntry | not-accessible | mandatory | The IP and community of the module hosted in the slot corresponding to the index. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.4.1.1 | ColumnhostSlotIndex | read-only | mandatory | The slot number. Varies from 1 to slotNumber. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.4.4.1.2 | ColumnhostIP | read-write | mandatory | The IP address of the hosted module. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.5 | Nodefan | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.5.1 | ScalarfanSpeed | read-write | mandatory | The speed of the fans. Set this variable to maximum(1) for maximum cooling where noise does not matter. Set this variable to normal(2) to cause fan speeds to b… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.5.2 | ScalarrightFanStatus | read-only | mandatory | The status of the right fan tray. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.5.3 | ScalarleftFanStatus | read-only | mandatory | The status of the left fan tray. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.6 | Nodebattery | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.6.1 | ScalarbatteryStatus | read-only | mandatory | The status of the backup battery. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.6.2 | ScalarbatteryUsing | read-only | mandatory | The source of power being used for the box. The value batteryPower(2) indicates that the backup battery unit is being used to power the GIGAswitch. The externa… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.6.3 | ScalarbatteryCharge | read-only | mandatory | The charge-level of the backup battery. Meaningful only if the battery is present. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.6.4 | ScalarbatteryTest | read-only | mandatory | Only the value test(3) can be written. Writes of other values are erroneous. This shows the result of the last battery test performed. Testing the battery is r… |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7 | Nodefppn | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7.1 | TablefppnTable | not-accessible | mandatory | A list of front panel port number to MIB-II interface number mappings. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1 | RowfppnEntry | not-accessible | mandatory | Assigns the MIB-II interface ifIndex for a physical datalink (cable) connection to the box. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.1 | ColumnfppnSlotNumber | read-only | mandatory | The 1-based slot number of the module. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.2 | ColumnfppnPortOfThatSlot | read-only | mandatory | The 1-based media connection to the module. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.3 | ColumnfppnIfIndex | read-only | mandatory | The assigned MIB-II ifIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.4 | ColumnfppnBridgePortNumber | read-only | mandatory | The assigned Bridge MIB dot1dBasePort. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.8 | NodelineCard | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.8.1 | TablemPortTable | not-accessible | mandatory | A list of mPort entries. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1 | RowmPortEntry | not-accessible | mandatory | A collection of objects containing information for a given mPort MAC entity |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1.1 | ColumnmPortSMTIndex | read-only | mandatory | The value of the SMT index associated with this mPort MAC. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1.2 | ColumnmPortMACIndex | read-only | mandatory | The value of the MAC index associated with this mPort MAC. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1.3 | ColumnmPortEnable | read-write | mandatory | When true, this link will be enabled to operate in concentrator mode, i.e. mport. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9 | Nodeled | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.1 | TableledTable | not-accessible | mandatory | A list of LED entries, one for each module. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.1.1 | RowledTableEntry | not-accessible | mandatory | Each entry describes the state of one module. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.1.1.1 | ColumnledTableIndex | read-only | mandatory | The module index into the table. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.1.1.2 | ColumnledCount | read-only | mandatory | The number of LEDs on this module. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.2 | TableledSlotTable | not-accessible | mandatory | A list of LED entries, one for each module LED. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1 | RowledEntry | not-accessible | mandatory | Each entry describes the state of one module LED. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.1 | ColumnledSlotIndex | read-only | mandatory | The slot index into the table. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.2 | ColumnledLedIndex | read-only | mandatory | The led index within the slot given by slotIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.3 | ColumnledDescr | read-only | mandatory | A textual description of the information which the LED is meant to convey. i.e.: +5 Volt Power, DC Okay ATM port activity. Diagnostic status. |
| 1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.4 | ColumnledProgram | read-only | mandatory | The ledProgram string is a sequence of instructions for the LED state. The LED constantly repeats the program. Each LED state is represented by a two octet seq… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2 | NodegigaBridge | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1 | NodefilterByReferencedExpression | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.1 | TableebrNportMatrixNameTable | not-accessible | mandatory | This table allows filter matrices to be succinctly specified and named. These matrices may later be used and combined in filter specifications. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1 | RowebrNportMatrixNameEntry | not-accessible | mandatory | A particular named filter matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.1 | ColumnebrNportMatrixName | read-only | mandatory | This name for a filter matrix is whatever the user likes, as long as it is a unique filter matrix name. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.2 | ColumnebrNportMatrixValue | read-write | mandatory | A matrix is expressed using a shorthand that says what input ports can talk to what output ports. An examples of a specification is: 11:1; 1:3-5; 2:0,3; 4-7,9:… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.3 | ColumnebrNportMatrixStatus | read-write | mandatory | Assigning the value invalid will result in an error while the matrix is still reference by some filter. All matrices are permanent; it is their usage which may… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.4 | ColumnebrNportMatrixFppnValue | read-write | mandatory | A matrix is expressed using a shorthand that says what input ports can talk to what output ports. An examples of a specification is: 1.1,2.1-14.2:1.1-14.2; 2.2… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2 | TableebrNportSapNameTable | not-accessible | mandatory | The filters specified by SAP protocol. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1 | RowebrNportSapNameEntry | not-accessible | mandatory | A portion of a particular filter for a particular SAP protocol. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.1 | ColumnebrNportSapName | read-only | mandatory | This name for a portion of a filter is whatever the user likes, as long as it is a unique ebrNportSapName. The combination of ebrNportSapNameSap and ebrNportSa… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.2 | ColumnebrNportSapNameSap | read-write | mandatory | The one-byte SAP. Changes to ebrNportSapProtoTable for this SAP are denied while filtering of the SAP is specified by reference to a named matrix using this ta… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.3 | ColumnebrNportSapMatrixName | read-write | mandatory | A ebrNportMatrixName. Multiple matrices for the same SAP are combined using an elementwise-OR operator. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.4 | ColumnebrNportSapNameDisp | read-write | mandatory | filter(1) : The filtering for this SAP is specified by the filter matrix. alwaysFilter(2) : Frames of this SAP (protocol) are filtered regardless of any other … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.5 | ColumnebrNportSapNameStatus | read-write | mandatory | This object specifies the permanence of the associated filter matrix, and also provides a means to delete a filter matrix. Writing invalid(1) to the object rem… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3 | TableebrNportSnapNameTable | not-accessible | mandatory | The filters specified by Protocol ID for the SNAP SAP. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1 | RowebrNportSnapNameEntry | not-accessible | mandatory | A portion of a particular filter for a particular Protocol ID. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.1 | ColumnebrNportSnapName | read-only | mandatory | This name for a portion of a filter is whatever the user likes, as long as it is a unique ebrNportSnapName. The combination of ebrNportSnapNameSnap and ebrNpor… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.2 | ColumnebrNportSnapNameSnap | read-write | mandatory | The five-byte PID. Changes to ebrNportSnapProtoTable for this protocol are denied while filtering of the protocol is specified by reference to a named matrix u… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.3 | ColumnebrNportSnapMatrixName | read-write | mandatory | A ebrNportMatrixName. Multiple matrices for the same PID are combined using an elementwise-OR operator. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.4 | ColumnebrNportSnapNameDisp | read-write | mandatory | filter(1) : The filtering for this Protocol ID is specified by the filter matrix. alwaysFilter(2) : Frames of this Protocol ID are filtered regardless of any o… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.5 | ColumnebrNportSnapNameStatus | read-write | mandatory | This object specifies the permanence of the associated filter matrix, and also provides a means to delete a filter matrix. Writing invalid(1) to the object rem… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4 | TableebrNportDANameTable | not-accessible | mandatory | The filters specified by destination address. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1 | RowebrNportDANameEntry | not-accessible | mandatory | A portion of a particular filter for a particular destination address. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.1 | ColumnebrNportDAName | read-only | mandatory | This name for a portion of a filter is whatever the user likes, as long as it is a unique ebrNportDAName. The combination of ebrNportDANameDA and ebrNportDAMat… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.2 | ColumnebrNportDANameDA | read-write | mandatory | The six-byte destination address. Changes to ebrNportStaticDATable for this address are denied while filtering of the address is specified by reference to a na… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.3 | ColumnebrNportDAMatrixName | read-write | mandatory | A ebrNportMatrixName. Multiple matrices for the same address are combined using an elementwise-OR operator. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.4 | ColumnebrNportDANameDisp | read-write | mandatory | filter(1) : The filtering for this address is specified by the filter matrix. alwaysFilter(2) : Frames destined to address are filtered regardless of any other… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.5 | ColumnebrNportDANameStatus | read-write | mandatory | other(1) - This entry is currently in use, but the conditions under which it will remain so are different from each of the following values. Like other uses of… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5 | TableebrNportSANameTable | not-accessible | mandatory | The filters specified by source address. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1 | RowebrNportSANameEntry | not-accessible | mandatory | A portion of a particular filter for a particular source address. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.1 | ColumnebrNportSAName | read-only | mandatory | This name for a portion of a filter is whatever the user likes, as long as it is a unique ebrNportSAName. The combination of ebrNportSANameSA and ebrNportSAMat… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.2 | ColumnebrNportSANameSA | read-write | mandatory | The six-byte source address. Changes to ebrNportStaticSATable for this address are denied while filtering of the address is specified by reference to a named m… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.3 | ColumnebrNportSAMatrixName | read-write | mandatory | A ebrNportMatrixName. Multiple matrices for the same address are combined using an elementwise-OR operator. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.4 | ColumnebrNportSANameDisp | read-write | mandatory | This object specifies how to interpret the ebrNportPortNum and the ebrNportSAMatrixName objects. portMask(1) : The static filtering for this address is specifi… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.5 | ColumnebrNportSANameStatus | read-write | mandatory | other(1) - This entry is currently in use, but the conditions under which it will remain so are different from each of the following values. Like other uses of… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.6 | ScalarebrNportDefaultMatrixValue | read-write | mandatory | A matrix is expressed using a shorthand that says what input ports can talk to what output ports. An examples of a specification is: 11:1; 1:3-5; 2:0,3; 4-7,9:… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.7 | ScalarebrNportManualFilter | read-write | mandatory | The list of bridge ports in manual mode is listed. Manual mode means that the bridge purges the learned entries for that port from its forwarding database, sto… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.8 | TableebrNportMatrixNameRowTable | not-accessible | mandatory | This table is another view of ebrNportMatrixNameTable. Changes to this table cause changes to ebrNportMatrixNameTable. Users or programs can choose whichever m… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1 | RowebrNportMatrixNameRowEntry | not-accessible | mandatory | A particular row of a particular named filter matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.1 | ColumnebrNportmatrixName | read-only | mandatory | This name for a filter matrix is whatever the user likes, as long as it is a unique filter matrix name. Same as ebrNportMatrixName. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.2 | ColumnebrNportMatrixReceivePort | read-only | mandatory | A bridge port number. Zero is treated as in other tables, and is short-hand for all rows not previously mentioned. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.3 | ColumnebrNportMatrixAllowedToGoTo | read-write | mandatory | Just like all the other GoTos. The set of ports to which frames received from a specific port are allowed to be forwarded. Each octet of this object specifies … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.4 | ColumnebrNportMatrixNameRowStatus | read-write | mandatory | Assigning the value invalid will delete the row of the matrix. Attempting to delete the last ebrNportmatrixName entry for a matrix will result in an error whil… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.9 | ScalarebrNportDefaultMatrixFppnValue | read-write | mandatory | A matrix is expressed using a shorthand that says what input front panel ports can talk to what output front panel ports. An examples of a specification is: 1.… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.10 | ScalarebrNportFppnManualFilter | read-write | mandatory | The list of front panel ports in manual mode is listed. Manual mode means that the bridge purges the learned entries for that port from its forwarding database… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.11 | TableebrNportMatrixFppnRowTable | not-accessible | mandatory | This table is yet another view of ebrNportMatrixNameTable. Changes to this table cause changes to ebrNportMatrixNameTable. Users or programs can choose whichev… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1 | RowebrNportMatrixFppnRowEntry | not-accessible | mandatory | A particular row of a particular named filter matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.1 | ColumnebrNportmatrixname | read-only | mandatory | This name for a filter matrix is whatever the user likes, as long as it is a unique filter matrix name. Same as ebrNportMatrixName. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.2 | ColumnebrNportMatrixFppnReceivePort | read-only | mandatory | Front panel port numbers are of the form (slot.connector), where slot is the slot number the module is plugged into, and connector is the connector number spec… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.3 | ColumnebrNportMatrixFppnAllowedToGoTo | read-write | mandatory | Just like all the other GoTos. The set of ports to which frames received from a specific port are allowed to be forwarded. Each octet of this object specifies … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.4 | ColumnebrNportMatrixFppnRowStatus | read-write | mandatory | Assigning the value invalid will delete the row of the matrix. Attempting to delete the last ebrNportmatrixname entry for a matrix will result in an error whil… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.12 | ScalarebrNportNamedDefaultMatrix | read-write | mandatory | When a matrix name is written to this object, the default matrix is set to the matrix if and only if the matrix exists. Unspecified rows in the matrix are set … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.13 | TableebrNportDefaultMatrixRowTable | not-accessible | mandatory | This table is another view of ebrNportDefaultMatrixValue. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.13.1 | RowebrNportDefaultMatrixRowEntry | not-accessible | mandatory | A particular row of the default matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.13.1.1 | ColumnebrNportDefaultMatrixReceivePort | read-only | mandatory | A bridge port number. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.13.1.2 | ColumnebrNportDefaultMatrixAllowedToGoTo | read-only | mandatory | The set of ports to which frames received from a specific port are allowed to be forwarded by default. Each octet of this object specifies a set of eight ports… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.14 | ScalarebrNportFloodMatrixValue | read-write | mandatory | A flood matrix is expressed using a shorthand that says what input ports can be flooded to what output ports. Unspecified rows are set to one's, which means th… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.15 | ScalarebrNportFloodMatrixFppnValue | read-write | mandatory | A flood matrix is expressed using a shorthand that says what input front panel ports can be flooded to what output front panel ports. Unspecified rows are set … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.16 | ScalarebrNportNamedFloodMatrix | read-write | mandatory | When a matrix name is written to this object, the flood matrix is set to the matrix if and only if the matrix exists. Unspecified rows in the matrix are set to… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.17 | TableebrNportFloodMatrixRowTable | not-accessible | mandatory | This table is another view of ebrNportFloodMatrixValue. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.17.1 | RowebrNportFloodMatrixRowEntry | not-accessible | mandatory | A particular row of the flood matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.17.1.1 | ColumnebrNportFloodMatrixReceivePort | read-only | mandatory | A bridge port number. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.1.17.1.2 | ColumnebrNportFloodMatrixAllowedToGoTo | read-only | mandatory | The set of ports to which frames received from a specific port are allowed to be flooded by default. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2 | NodefilterByBitmapValue | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.1 | TableebrNportSapProtoTable | not-accessible | mandatory | A table that contains filtering information about 802.2 SAPs in the DSAP field for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1 | RowebrNportSapProtoEntry | not-accessible | mandatory | A table that contains filtering information about 802.2 SAPs in the DSAP field for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1.1 | ColumnebrNportSapValue | read-write | mandatory | The 802.2 DSAP in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1.2 | ColumnebrNportSapReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrNportSapAllowedToGoTo. A value of zero indicates that this entry applies on all ports … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1.3 | ColumnebrNportSapAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and containing the DSAP in an 802 frame specified by ebrNportSapValue are allowed to be forwarde… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.2 | TableebrNportSapFilterCharacteristicsTable | not-accessible | mandatory | A table that contains information about how 802.2 DSAP filters are used within N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1 | RowebrNportSapFilterCharacteristicsEntry | not-accessible | mandatory | 802.2 DSAP filter usage for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1.1 | ColumnebrNportSapFilterCharacteristicsSapValue | read-write | mandatory | The 802.2 DSAP in a frame to which this entry's information applies. The value of this object is the same as ebrNportSapValue. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1.2 | ColumnebrNportSapDisp | read-write | mandatory | This object specifies how to interpret the ebrNportSapAllowedToGoTo values for the specified SAP. filter(1) : The filtering for this SAP is specified by the fi… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1.3 | ColumnebrNportSapStatus | read-write | mandatory | This object specifies the permanence of the associated filter matrix, and also provides a means to delete a filter matrix. Writing invalid(1) to the object rem… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.3 | TableebrNportSnapProtoTable | not-accessible | mandatory | A table that contains filtering information about 5-byte SNAP Protocol IDs (PIDs) for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1 | RowebrNportSnapProtoEntry | not-accessible | mandatory | A table that contains filtering information about 5-byte SNAP Protocol IDs (PIDs) for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1.1 | ColumnebrNportSnapValue | read-write | mandatory | The SNAP Protocol ID (PID) in an 802 frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1.2 | ColumnebrNportSnapReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrNportSnapAllowedToGoTo. A value of zero indicates that this entry applies on all ports… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1.3 | ColumnebrNportSnapAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and containing the SNAP PID in an 802 frame specified by ebrNportSnapValue are allowed to be for… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.4 | TableebrNportSnapFilterCharacteristicsTable | not-accessible | mandatory | A table that contains information about how SNAP Protocol ID (PID) filters are used within N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1 | RowebrNportSnapFilterCharacteristicsEntry | not-accessible | mandatory | 802.2 SNAP Protocol ID (PID) filter usage for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1.1 | ColumnebrNportSnapFilterCharacteristicsSnapValue | read-write | mandatory | The SNAP Protocol ID (PID) in a frame to which this entry's information applies. The value of this object is the same as ebrNportSnapValue. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1.2 | ColumnebrNportSnapDisp | read-write | mandatory | This object specifies how to interpret the ebrNportSnapAllowedToGoTo values for the specified SNAP PID. filter(1) : The filtering for this Protocol ID is speci… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1.3 | ColumnebrNportSnapStatus | read-write | mandatory | This object specifies the permanence of the associated filter matrix, and also provides a means to delete a filter matrix. Writing invalid(1) to the object rem… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.5 | TableebrNportStaticDATable | not-accessible | mandatory | This table contains management-specified destination address filtering information about unicast and multicast addresses for N-port bridges. In RFC 1286 lingo,… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1 | RowebrNportStaticDAEntry | not-accessible | mandatory | Information about a specific MAC address for which the bridge has some management-specified forwarding and/or filtering information. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1.1 | ColumnebrNportDAAddress | read-write | mandatory | The destination MAC Address in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1.2 | ColumnebrNportDAReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrNportDAAllowedToGoTo field. A value of zero indicates that this entry applies on all p… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1.3 | ColumnebrNportDAAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and destined to the address specified by ebrNportDAAddress are allowed to be forwarded. Each oct… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.6 | TableebrNportStaticDAFilterCharacteristicsTable | not-accessible | mandatory | A table that contains information about how static destination address filters (for unicast and multicast addresses) are used within N-port bridges. Static obj… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1 | RowebrNportStaticDAFilterCharacteristicsEntry | not-accessible | mandatory | Information about a specific static MAC destination address filter's usage within N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1.1 | ColumnebrNportDestinationAddress | read-write | mandatory | The destination MAC Address in a frame to which this entry's information applies. The value of this object is the same as ebrNportDAAddress. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1.2 | ColumnebrNportDADisp | read-write | mandatory | This object specifies how to interpret the ebrNportPortNum and ebrNportDAAllowedToGoTo objects. filter(1) : The filtering for this address is specified by the … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1.3 | ColumnebrNportDAStatus | read-write | mandatory | other(1) - This entry is currently in use, but the conditions under which it will remain so are different from each of the following values. Like other uses of… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.7 | TableebrNportStaticSATable | not-accessible | mandatory | A table that contains static source address filtering information about unicast and multicast addresses for N-port bridges. Static objects are those objects wh… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1 | RowebrNportStaticSAEntry | not-accessible | mandatory | Information about a specific MAC address for which the bridge has some static forwarding and/or filtering information. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1.1 | ColumnebrNportSAAddress | read-write | mandatory | The source MAC Address in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1.2 | ColumnebrNportSAReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrNportSAAllowedToGoTo field. A value of zero indicates that this entry applies on all p… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1.3 | ColumnebrNportSAAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and sourced from the address specified by ebrNportSAAddress are allowed to be forwarded. Each oc… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.8 | TableebrNportStaticSAFilterCharacteristicsTable | not-accessible | mandatory | A table that contains information about how static source address filters (for unicast and multicast addresses) are used within N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1 | RowebrNportStaticSAFilterCharacteristicsEntry | not-accessible | mandatory | Static source address filter usage for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1.1 | ColumnebrNportSourceAddress | read-write | mandatory | The source MAC Address in a frame to which this entry's information applies. The value of this object is the same as ebrNportSAAddress. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1.2 | ColumnebrNportSADisp | read-write | mandatory | This object specifies how to interpret the ebrNportPortNum and and the ebrNportSAAllowedToGoTo objects. portMask(1) : The static filtering for this address is … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1.3 | ColumnebrNportSAStatus | read-write | mandatory | other(1) - This entry is currently in use, but the conditions under which it will remain so are different from each of the following values. Like other uses of… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.9 | TableebrNportSwTable | not-accessible | mandatory | This table describes the default filter matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.9.1 | RowebrNportSwEntry | not-accessible | mandatory | The entry describes a row of the default filter matrix. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.9.1.1 | ColumnebrNportSwReceivePort | read-write | mandatory | The bridge port on which a frame must be received to use the corresponding ebrNportSwAllowedToGoTo field. A value of zero indicates that this entry applies on … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.9.1.2 | ColumnebrNportSwAllowedToGoTo | read-write | mandatory | This object specifies the default forwarding disposition after all DA, SA, and protocol filters have been applied. For those cases where no filter applies to t… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.2.10 | ScalarebrNportSwManualFilter | read-write | mandatory | A switch that controls address filtering. Specifying a one in a bit position says that the port is in manual mode. Each octet of this object specifies a set of… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.3 | TableebrNportPortNumTable | not-accessible | mandatory | A table that contains static (i.e., configured by network management) information about the bridge port on which unicast or multicast addresses reside on N-por… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.3.1 | RowebrNportPortNumEntry | not-accessible | mandatory | Information about a specific MAC address. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.1 | ColumnebrNportPortNumAddress | read-write | mandatory | The MAC Address to which this entry's information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.2 | ColumnebrNportPortNum | read-write | mandatory | The Port Number to which this address will be translated (to which frames destined for the address will be forwarded). There are some filtering nuances for add… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.3 | ColumnebrNportPortNumStatus | read-write | mandatory | This object specifies the permanence of the specified information, and also provides a means to delete an entry. Writing invalid(1) to the object removes the e… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.4 | ColumnebrNportFppnPortNum | read-write | mandatory | The Front Panel Port Number to which this address will be translated (to which frames destined for the address will be forwarded). There are some filtering nua… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5 | NodeserviceClassAssignments | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.1 | TableebrNportSapSvcTable | not-accessible | mandatory | A table that contains resource information (e.g., queuing) about 802.2 SAPs in the DSAP field for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1 | RowebrNportSapSvcEntry | not-accessible | mandatory | Resource information about an 802.2 SAP in the DSAP field for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.1 | ColumnebrNportSapSvcSapValue | read-write | mandatory | The 802.2 DSAP in a frame to which this entry's resource information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.2 | ColumnebrNportSapSvc | read-write | mandatory | The service class used to allocate resources and implement service policy within the bridge. The service class associated with a frame is a function of either … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.3 | ColumnebrNportSapSvcStatus | read-write | mandatory | This object specifies the permanence of the specified service class usage, and also provides a means to delete an entry. Writing invalid(1) to the object remov… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.4 | ColumnebrNportSapSinglePath | read-write | mandatory | The ebrNportSapSinglePath object is used to set the single path ports for a ebrNportSapSvcSapValue. The default is to not use the default (single path) service… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.2 | TableebrNportSnapSvcTable | not-accessible | mandatory | A table that contains resource information (e.g., queuing) about 5-byte SNAP Protocol IDs (PIDs) for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1 | RowebrNportSnapSvcEntry | not-accessible | mandatory | Resource information about a 5-byte SNAP Protocol ID (PID) for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.1 | ColumnebrNportSnapSvcSnapValue | read-write | mandatory | The SNAP Protocol ID (PID) in a frame to which this entry's resource information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.2 | ColumnebrNportSnapSvc | read-write | mandatory | The service class used to allocate resources and implement service policy within the bridge. The service class associated with a frame is a function of either … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.3 | ColumnebrNportSnapSvcStatus | read-write | mandatory | This object specifies the permanence of the specified service class usage, and also provides a means to delete an entry. Writing invalid(1) to the object remov… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.4 | ColumnebrNportSnapSinglePath | read-write | mandatory | The ebrNportSnapSinglePath object is used to set the single path ports for a ebrNportSnapSvcSnapValue. The default is to not use the default (single path) serv… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.3 | TableebrNportDASvcTable | not-accessible | mandatory | A table that contains resource information about unicast and multicast destination addresses for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1 | RowebrNportDASvcEntry | not-accessible | mandatory | Resource information about a specific MAC destination address for N-port bridges. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1.1 | ColumnebrNportSvcAddress | read-write | mandatory | The destination MAC Address in a frame to which this entry's resource information applies. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1.2 | ColumnebrNportSvc | read-write | mandatory | The service class used to allocate resources and implement service policy within the bridge. The service class associated with a frame is a function of either … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1.3 | ColumnebrNportSvcStatus | read-write | mandatory | This object specifies the permanence of the specified service class usage, and also provides a means to delete an entry. Writing invalid(1) to the object remov… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6 | Nodeflooding | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.1 | ScalarfloodUnknownUnicastRate | read-write | mandatory | The maximum bytes-per-second bandwidth of packets multicast because the destination address was not yet learned by the bridge. The resolution of this value is … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.2 | ScalarfloodMulticastRate | read-write | mandatory | The maximum bytes-per-second bandwidth of packets multicast because the destination address is a multicast address.The resolution of this value is 100 bytes-pe… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3 | TablefloodTable | not-accessible | mandatory | Detailed view of the bridge flooding process. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1 | RowfloodEntry | not-accessible | mandatory | Flooding state for a packet class and source. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.1 | ColumnfloodQuotaQualifier | read-only | mandatory | The quota qualifier describes an incoming or outgoing port. It is a linear index to the port starting from 1. If n is the quota qualifier for the first port of… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.2 | ColumnfloodQuotaClass | read-only | mandatory | The quota class describes the type of packet. Four packet types are classified as follows: 1 - Unknown Destination Packets, 2 - Multicast Packets, 3 - IS-IS Pa… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.3 | ColumnfloodBytesSent | read-only | mandatory | This object is the count of bytes in flooded packets. It does not include filtered packets or packets discarded due to buffer limitations. Each packet is count… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.4 | ColumnfloodPacketsSent | read-only | mandatory | This object is the count of flooded packets. It does not include filtered packets or packets discarded due to buffer limitations. Each packet is counted once, … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.5 | ColumnfloodGeezers | read-only | mandatory | This object is the count of packets that could not be flooded because they had remained in the SCP or in the inbound linecard too long. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.6 | ColumnfloodLosers | read-only | mandatory | This object is the count of packets discarded by the SCP flooding software (at the interrupt level) due to insufficient buffering. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.7 | ColumnfloodHogs | read-only | mandatory | This object is the count of packets for which buffer quota conversion to flooding software optimistic quotas failed. This includes packets that were discarded … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.8 | ColumnfloodSinglePathDiscards | read-only | mandatory | This object is the count of packets discarded to prevent packet misordering. Certain protocol types are considered single-path and may not be delivered out of … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.9 | ColumnfloodPacketsFiltered | read-only | mandatory | This object is the count of packets discarded by the flooding software because user-configured filtering resulted in no allowed outbound transmit ports. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.10 | ColumnfloodPacketsPurged | read-only | mandatory | This object is the count of packets discarded due to the incoming link leaving FORWARDING state while they were buffered by flooding software. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.11 | ColumnfloodBytesPurged | read-only | mandatory | This object is the byte count in packets discarded due to the incoming link leaving FORWARDING state while they were buffered by flooding software. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.12 | ColumnfloodLocalCopyPacketsDelivered | read-only | mandatory | This object is the count of multicast packets addressed to software modules in the SCP that have been successfully delivered to those modules. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.13 | ColumnfloodLocalCopyPacketsDiscarded | read-only | mandatory | This object is the count of multicast packets addressed to software modules in the SCP that, because of buffer limitations, could not be delivered to those mod… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7 | NodecutThrough | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.1 | TablecutThroughTable | not-accessible | mandatory | This table controls the enabling of some hardware performance enhancements that avoid store-and-forward delays during packet forwarding, whenever possible. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1 | RowcutThroughEntry | not-accessible | mandatory | Information about the enabling of some hardware performance enhancements that avoid store-and-forward delays for a specific bridge port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1.1 | ColumncutThroughBridgePort | read-write | mandatory | The dot1dBasePort bridge port number for this table entry. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1.2 | ColumncutThroughInbound | read-write | mandatory | If true, some hardware performance enhancements are enabled to avoid store-and-forward delays when packets enter the GIGAswitch. If false, the whole packet is … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1.3 | ColumncutThroughOutbound | read-write | mandatory | If true, some hardware performance enhancements are enabled to avoid store-and-forward delays when packets leave the GIGAswitch. If false, the whole packet is … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.2 | TablecutThroughFppnTable | not-accessible | mandatory | This table controls the enabling of some hardware performance enhancements that avoid store-and-forward delays during packet forwarding, whenever possible. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1 | RowcutThroughFppnEntry | not-accessible | mandatory | Information about the enabling of some hardware performance enhancements that avoid store-and-forward delays for a specific front panel port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1.1 | ColumncutThroughFppnPort | read-write | mandatory | The front panel port number for this table entry. Front panel port numbers are of the form (slot.connector), where slot is the slot number the module is plugge… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1.2 | ColumncutThroughFppnInbound | read-write | mandatory | If true, some hardware performance enhancements are enabled to avoid store-and-forward delays when packets enter the GIGAswitch. If false, the whole packet is … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1.3 | ColumncutThroughFppnOutbound | read-write | mandatory | If true, some hardware performance enhancements are enabled to avoid store-and-forward delays when packets leave the GIGAswitch. If false, the whole packet is … |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.8 | NodegigaStp | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.8.1 | TablegigaStpPortTable | not-accessible | mandatory | A list of gigaStp entries |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.8.1.1 | RowgigaStpPortEntry | not-accessible | mandatory | A collection of objects containing information for a given StpPort |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.8.1.1.1 | ColumngigaStpPortIfIndex | read-only | mandatory | The value of the interface associated with this spanning tree port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.8.1.1.2 | ColumngigaStpPortSpanningTreeEnable | read-write | mandatory | When true, this interface will be enabled to operate as part of the spanning tree. When trueNoDelay, this interface will be enabled to operate as part of the s… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.8.2 | ScalargigaStpDemandLearningEnable | read-write | mandatory | If true, then when a source address is learned, the address is only written to the Translation Table in the bridge port on which it was learned. If the address… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.9 | NodetranslationTableParams | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.9.1 | ScalarttSize | read-only | mandatory | The number of entries in the tables used to store learned network addresses. |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.10 | NodexacInDiscardCounters | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.10.1 | ScalarxacInDiscardUnknownDAUCast | read-only | mandatory | This object shows the number of unknown DA unicast packets which are transmitted from linecards to the SCP for multicasting, but discarded due to the lack of b… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.10.2 | ScalarxacInDiscardMulticast | read-only | mandatory | This object shows the number of multicast packets which are transmitted from linecards to the SCP for processing, but discarded due to the lack of buffer space… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.10.3 | ScalarxacInDiscardIPForwarding | read-only | mandatory | This object shows the number of IP packets which are transmitted from linecards to the SCP for forwarding, but discarded due to the lack of buffer space in the… |
| 1.3.6.1.4.1.36.2.15.3.3.3.2.11 | NodecommunityString | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.2.11.1 | ScalarcommunityStringDelimiter | read-write | mandatory | The communityStringDelimiter object is used to delimit community string suffixes. Community string suffixes give the SNMP agent additional information to proce… |
| 1.3.6.1.4.1.36.2.15.3.3.3.3 | NodegigaUpgradeSoftware | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1 | NodedoTransfer | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1.1 | ScalartftpDestination | read-write | mandatory | This object is the IP address of the host storing the file containing the software image. The object may not be set until the last requested transfer succeeds … |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1.2 | ScalarmopDestination | read-write | mandatory | This object is the 802 48-bit address of the host storing the file containing the software image. The object may not be set until the last requested transfer s… |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1.3 | ScalartransferFileName | read-write | mandatory | This object is the name of the file containing the software image. The object may not be set until the last requested transfer succeeds or fails. Before settin… |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1.4 | ScalartransferAction | read-write | mandatory | To initiate a transfer of a file from a server to the SCP, set this object. If transferFileName is non-empty, and mopDestination is non-zero, setting this obje… |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1.5 | ScalartransferStatus | read-only | mandatory | This variable can be polled to determine when the transfer has completed. Polling for completion allows other SNMP requests to be processed while the transfer … |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.1.6 | ScalartransferSize | read-only | mandatory | Size in bytes of the transfered file. This object can be polled along with the transferStatus object to monitor the progress of the transfer. |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.2 | NodeuseTransfer | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.3.2.1 | ScalarcopyToSlot | read-write | mandatory | The slot number of the card which is to be upgraded. The object may not be set until the last requested copy succeeds or fails. |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.2.2 | ScalarcopyType | read-only | mandatory | The type of the image. The object is set after a transfer succeeds or fails. |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.2.3 | ScalarcopyAction | read-write | mandatory | To initiate a software upgrade of a card, set this object. If copyToSlot is non-zero, and copyType has a value other than 'none', and transferStatus has the va… |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.2.4 | ScalarcopyStatus | read-only | mandatory | This variable can be polled to determine when the card upgrade has completed. Polling for completion allows other SNMP requests to be processed while the copy … |
| 1.3.6.1.4.1.36.2.15.3.3.3.3.3 | ScalardeleteTransfer | read-write | mandatory | When read, this object indicates whether the result of a file transfer is still present. The value exists indicates that the transferred file is present; the v… |
| 1.3.6.1.4.1.36.2.15.3.3.3.4 | NodegigaIP | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.4.1 | NodearpTimingMechanism | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.4.1.1 | ScalararpTimeoutInSeconds | read-write | mandatory | The maximum amount of time an IP to LAN address translation will be used if it cannot be re-verified. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.1.2 | ScalararpPeriodBetweenRequests | read-write | mandatory | The time, in seconds, between ARP requests that are used to verify or to discover an IP to LAN address translation. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.1.3 | ScalararpRequestRetries | read-write | mandatory | The number of times ARP requests are used to verify or to discover an IP to LAN address translation. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.2 | NodesnmpParameters | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.4.2.1 | ScalarsnmpDuplicateDiscardInterval | read-write | mandatory | If duplicated snmp messages arrive within this interval, all but the first one will be discarded. The unit is a hundredth of second. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.3 | NodearpControlParams | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.4.3.1 | ScalararpAgent | read-write | mandatory | When true, the GIGAswitch will service broadcast ARP requests from its ARP cache. When false, Broadcast ARP frames are flooded. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4 | NodearpStatisticalCounters | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1 | TablearpStatisticalTable | not-accessible | mandatory | This table stores ARP counters. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1 | RowarpStatisticalEntry | not-accessible | mandatory | Information about the ARP statistical table is stored. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.1 | ColumnarpStatisticalIfIndex | read-only | mandatory | Identifies the Interface. The value of this object is the same as the ifIndex, defined in MIB-II, for this interface. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.2 | ColumnarpUnicastReceived | read-only | mandatory | Unicast ARP requests received on this port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.3 | ColumnarpBroadcastReceived | read-only | mandatory | Broadcast ARP requests received on this port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.4 | ColumnarpRepliesTransmitted | read-only | mandatory | ARP replies transmitted on this port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.5 | ColumnarpFramesFlooded | read-only | mandatory | ARP frames received on this port that required flooding while acting as an ARP agent. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.6 | ColumnarpFramesDiscarded | read-only | mandatory | ARP frames received on this port that were discarded due to protocol errors. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5 | NodeipSwitching | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.1 | ScalaripSwitchEnable | read-write | mandatory | If true then switched IP filtering is enabled. If false switched IP filtering is disabled. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2 | TableipSwitchPortsTable | not-accessible | mandatory | This table allows the user to assign an address range to logical bridge ports so that all traffic destined to addresses within that range will go out those por… |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1 | RowipSwitchPortsEntry | not-accessible | mandatory | An entry that stores information about a switched IP filtering range. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.1 | ColumnipRangeStartAddr | read-only | mandatory | An index for the ipSwitchPortsTable. This is the start address of the range of addresses for which the the ipStaticPorts and ipDynamicPorts are valid. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.2 | ColumnipRangeEndAddr | read-only | mandatory | An index for the ipSwitchPortsTable. This is the end address of the range of addresses for which the the ipStaticPorts and ipDynamicPorts are valid. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.3 | ColumnipIPAddr | read-only | mandatory | The IP address associated with the range, ipRangeStartAddr and ipRangeEndAddr. |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.4 | ColumnipStaticPorts | read-write | mandatory | ipStaticPorts is the set of logical ports that packets will exit the Gigaswitch when the destination address is within the range specified by ipRangeStartAddr … |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.5 | ColumnipDynamicPorts | read-only | mandatory | ipDynamicPorts is the set of logical ports, learned dynamically, that packets will exit the Gigaswitch when the destination address is within the range specifi… |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.3 | ScalaripPrimaryPorts | read-write | mandatory | ipPrimaryPorts is the set of all logical ports, set by management, that packets will exit the Gigaswitch regardless of the range to which they are addressed to… |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.4 | ScalaripDynamicPrimaryPorts | read-only | mandatory | ipPrimaryPorts is the set of all logical ports, learned dynamically, that packets will exit the Gigaswitch regardless of the range to which they are addressed … |
| 1.3.6.1.4.1.36.2.15.3.3.3.4.5.5 | ScalaripDynamicEnabledPorts | read-write | mandatory | ipSwitchDynamicEnabledPorts is the set of bridge ports over which the GIGAswitch sends and receives information about configured IP address ranges. The syntax … |
| 1.3.6.1.4.1.36.2.15.3.3.3.5 | NodegigaSets | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1 | TableportGroupMembershipTable | not-accessible | mandatory | The table for storing the port group membership. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1 | RowportGroupMembershipEntry | not-accessible | mandatory | An entry stores information about a single port group. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.1 | ColumnportGroupBridgePort | read-only | mandatory | The port group port number. It is unique within this table and must be between 37 and 64. Without management settings, the port group has no members in it. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.2 | ColumnportGroupMembership | read-only | mandatory | This object displays the current state of the port group membership. Managers specify a new port group membership using portGroupMembershipWorkBuf. The new mem… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.3 | ColumnportGroupMembershipWorkBuf | read-write | mandatory | Managers can update a new port group membership as many times as they want using this object. Setting this object to a new value does not change the current me… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.4 | ColumnportGroupPortType | read-only | mandatory | This object displays the current state of the port group port type. Managers specify a new port group port type using portGroupPortTypeWorkBuf. The new port ty… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.5 | ColumnportGroupPortTypeWorkBuf | read-write | mandatory | Managers can update a new port group port type as many times as they want using this object. Setting this object to a new value does not change the current por… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.6 | ColumnportGroupPortOperStatus | read-only | mandatory | This object indicates the operational status of the port group. The status represents the aggregated effect of each member's status. uninitializedPort(1) state… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2 | TableportGroupFppnMembershipTable | not-accessible | mandatory | The table for storing the port group membership specified by FPPN numbers. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1 | RowportGroupFppnMembershipEntry | not-accessible | mandatory | An entry stores information about a single port group. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.1 | ColumnportGroupFppnPort | read-only | mandatory | The port group port number. It is unique within this table and must be between 99.37 and 99.64. Without management settings, the port group has no members in i… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.2 | ColumnportGroupFppnMembership | read-only | mandatory | This object displays the current state of the port group membership. Managers specify a new port group membership using portGroupFppnMembershipWorkBuf. The new… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.3 | ColumnportGroupFppnMembershipWorkBuf | read-write | mandatory | Managers can update a new port group membership as many times as they want using this object. Setting this object to a new value does not change the current me… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.4 | ColumnportGroupFppnPortType | read-only | mandatory | This object displays the current state of the port group port type. Managers specify a new port group port type using portGroupPortTypeWorkBuf. The new port ty… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.5 | ColumnportGroupFppnPortTypeWorkBuf | read-write | mandatory | Managers can update a new port group port type as many times as they want using this object. Setting this object to a new value does not change the current por… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.6 | ColumnportGroupFppnPortOperStatus | read-only | mandatory | This object indicates the operational status of the port group. The status represents the aggregated effect of each member's status. uninitializedPort(1) state… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.3 | TableportGroupStatusTable | not-accessible | mandatory | The table for storing the port status. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.3.1 | RowportGroupStatusEntry | not-accessible | mandatory | An entry stores the port status. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.1 | ColumnportGroupStatusBridgePort | read-only | mandatory | The bridge port number runs from 1 to _LASTPHYSPORT_. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.2 | ColumnportGroupStatusPortNumber | read-only | mandatory | If the indexed port is a member of a port group, the port group number is returned. Otherwise, the index itself is returned. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.3 | ColumnportGroupStatusPortType | read-only | mandatory | This object represents the port type. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.4 | ColumnportGroupStatusOperStatus | read-only | mandatory | This object indicates the operational status of the indexed port. uninitializedPort(1) state indicates one of the followings: 1) the port is nonexistent, 2) th… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.4 | TablelearningDomainMembershipTable | not-accessible | mandatory | This table allows learning domains to be created, modified, and deleted. There can be from 1 to 8 learning domains. A learning domain is a collection of port g… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.4.1 | RowlearningDomainMembershipEntry | not-accessible | mandatory | A group of objects, indexed by learningDomainNumber, that specify learning domain attributes. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.4.1.1 | ColumnlearningDomainNumber | read-only | mandatory | The index for a learning domain is an integer with range, 1-8, where 1 is the default learning domain. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.4.1.2 | ColumnlearningDomainMembership | read-only | mandatory | This object displays the current state of the learning domain membership. Managers specify a new learning domain membership using learningDomainMembershipWorkB… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.4.1.3 | ColumnlearningDomainMembershipWorkBuf | read-write | mandatory | The learningDomainMembershipWorkBuf object is used to create,modify, and delete learning domains. Managers can update a learning domain membership as many time… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.5 | TableportTargetDomainListMembershipTable | not-accessible | mandatory | This table allows port target domains lists to be created, modified, and deleted. The port target domain list is the set of all mgmt defined learning domains t… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.5.1 | RowportTargetDomainListMembershipEntry | not-accessible | mandatory | A group of objects, indexed by portTargetDomainListIndex, that specify port target domain attributes. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.5.1.1 | ColumnportTargetDomainListIndex | read-only | mandatory | A bridge port number from 1 - 64 . |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.5.1.2 | ColumnportTargetDomainListMembership | read-only | mandatory | The portTargetDomainListMembership specifies a set of mgmt specified learning domains. This object displays the current state of the port target domain list me… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.5.1.3 | ColumnportTargetDomainListMembershipWorkBuf | read-write | mandatory | The portTargetDomainListMembership object is used to create, modify, and delete port target domain lists. Managers can update a port target domain membership l… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.6 | TablelBDomainMembershipTable | not-accessible | mandatory | The table for storing the logical bridge domain membership. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.6.1 | RowlBDomainMembershipEntry | not-accessible | mandatory | An entry stores information about a logical bridge domain. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.6.1.1 | ColumnlBDomainNumber | read-only | mandatory | The logical bridge domain number. It is unique within this table and must be between 1 and 8. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.6.1.2 | ColumnlBDomainMembership | read-only | mandatory | This object displays the learning domain numbers which are members of the indexed logical bridge domain in the current box configuration. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.6.1.3 | ColumnlBDomainMembershipWorkBuf | read-write | mandatory | Managers can specify logical bridge domains as many times as needed without effecting the current box configuration using this object. Setting this object to a… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.7 | ScalarportGroupAction | read-write | mandatory | To initiate a configuration upgrade of a box, set this object. The tables updated with this set operation are: portGroupMembershipTable, learningDomainMembersh… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.8 | ScalarportGroupActionStatus | read-only | mandatory | This object shows the result of the most recent setting of portGroupAction to doUpdate(2). |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.9 | TabletrafficGroupMembershipTable | not-accessible | mandatory | This table allows the user to add and delete physical ports to traffic groups. There can be from 1 to 16 traffic groups. A traffic group is a collection of phy… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.9.1 | RowtrafficGroupMembershipEntry | not-accessible | mandatory | An entry that stores information about a traffic group. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.9.1.1 | ColumntrafficGroupNumber | read-only | mandatory | The index for the traffic group membership is a traffic group number. Traffic group numbers are in the range 1-16. Traffic group 1 is the default traffic group. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.9.1.2 | ColumntrafficGroupMembership | read-write | mandatory | The trafficGroupMembership object allows the user to add and delete physical ports from traffic groups. Because a physical port can only belong to one traffic … |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.10 | TabletrafficGroupAttributeTable | not-accessible | mandatory | This table allows traffic group attributes to be set. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.10.1 | RowtrafficGroupAttributeEntry | not-accessible | mandatory | An entry that stores traffic group attributes. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.1 | ColumntrafficGroupNum | read-only | mandatory | One of two indexes into the trafficGroupAttributeTable. It is within the range 1-16. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.2 | ColumntrafficGroupHgNumber | read-only | mandatory | Second of two indexes into the trafficGroupAttributeTable. This is the hunt group that all ports in the traffic group are assigned to and is in the range 37-64. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.3 | ColumntrafficGroupHgMember | read-write | mandatory | The trafficGroupHgMember is a number in the range 1-16 that maps to a member of the hunt group specified by trafficGroupHgNumber. trafficGroupHgMember 1 maps t… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.4 | ColumntrafficGroupCategory | read-write | mandatory | The trafficGroupCatagory is defined as follows : fixed fixed means that traffic is to stay on the same port until the port fails. For this value, the member nu… |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.11 | TablelearningQuotaTable | not-accessible | mandatory | Each logical bridge domain (LBD) has a learning quota. This table allows the setting of theses quotas. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.11.1 | RowlearningQuotaEntry | not-accessible | mandatory | A group of objects, indexed by learningQuotaNumber, that specify learning quotas. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.11.1.1 | ColumnlearningQuotaNumber | read-only | mandatory | The index for a learning quota is a learning domain with range, 1 - 8. |
| 1.3.6.1.4.1.36.2.15.3.3.3.5.11.1.2 | ColumnlearningQuota | read-write | mandatory | Each learning domain has a learning quota. The ports in the domain are guaranteed the ability to use approximately this number of address entries in the Transl… |
| 1.3.6.1.4.1.36.2.15.3.3.3.6 | NodegigaSnmpDebug | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.6.1 | ScalarcommitFails | read-write | mandatory | Exercise abort undo code in SNMP commit processing |
| 1.3.6.1.4.1.36.2.15.3.3.3.7 | NodegigaXglEthernetGroup | |||
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1 | TablexglTable | not-accessible | mandatory | This table contains miscellaneous objects for configuring Fast Ethernet interfaces. |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1 | RowxglEntry | not-accessible | mandatory | Data for a particular Fast Ethernet interface. This table may be optionally implemented in such a way as to allow pre-configuration of hardware which has not y… |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.1 | ColumnxglCompliantMtu | read-write | mandatory | When true, packets with a data unit of size <= 1500 bytes are sent and received. When false, packets with a data unit of size <= 1535 bytes are sent and receiv… |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.2 | ColumnxglDisableIcmpErrors | read-write | mandatory | When true(1), ICMP redirect message processing is disabled for the specified port. |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.3 | ColumnxglTxErrorsToIcmpFifo | read-write | mandatory | When true(1), transmit errors are sent to the ICMP FIFO. |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.4 | ColumnxglRxErrorsToIcmpFifo | read-write | mandatory | When true(1), receive errors are sent to the ICMP FIFO. |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.5 | ColumnxglEnableAppletalkArpII | read-write | mandatory | When true(1), enables Appletalk ARP II support. |
| 1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.6 | ColumnxglEnableRawIPX | read-write | mandatory | When true(1), enables raw IPX support. |
| 1.3.6.1.4.1.36.2.15.3.3.4 | Nodeagl | |||
| 1.3.6.1.4.1.36.2.15.3.3.4.1 | NodeaglConfig | |||
| 1.3.6.1.4.1.36.2.15.3.3.4.1.1 | TableaglInterfaceConfTable | not-accessible | mandatory | This table contains the AGL specific interface configuration parameters, one entry per ATM interface port. |
| 1.3.6.1.4.1.36.2.15.3.3.4.1.1.1 | RowaglInterfaceConfEntry | not-accessible | mandatory | This list contains ATM interface configuration parameters and state variables. |
| 1.3.6.1.4.1.36.2.15.3.3.4.1.1.1.1 | ColumnaglInterfaceIndex | read-only | mandatory | The value of this object identifies the AGL port interface for which this entry contains management information. |
| 1.3.6.1.4.1.36.2.15.3.3.4.1.1.1.2 | ColumnaglInterfacePhyType | read-only | mandatory | Indicates the type of physical interface used on the ATM port. Two physical layer types are supported: 1. STS3c/STM1 2. DS3/E3 The type is unknown if the port … |
| 1.3.6.1.4.1.36.2.15.3.3.4.1.1.1.3 | ColumnaglInterfaceTrafficRateGranularity | read-only | mandatory | Indicates the granularity in cell/s for assigning peak, average and minimum guaranteed rates for traffic shaped circuits on the AGL port. This value also repre… |
| 1.3.6.1.4.1.36.2.15.3.3.4.2 | NodeaglSonet | |||
| 1.3.6.1.4.1.36.2.15.3.3.4.2.1 | TableaglInterfaceSonetTable | not-accessible | mandatory | This table contains the AGL specific interface configuration parameters for the SONET/SDH physical layer. |
| 1.3.6.1.4.1.36.2.15.3.3.4.2.1.1 | RowaglInterfaceSonetEntry | not-accessible | mandatory | This list contains SONET/SDH interface configuration parameters and state variables. |
| 1.3.6.1.4.1.36.2.15.3.3.4.2.1.1.1 | ColumnaglInterfaceSonetIndex | read-only | mandatory | The value of this object identifies the AGL port interface for which this entry contains management information and is the same as aglInterfaceIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.4.2.1.1.2 | ColumnaglInterfaceSonetMode | read-write | mandatory | Specifies whether the PHY operates in SONET STS-3c or SDH STM-1 mode. The following code points are used: 1 SONET STS-3c 2 SDH STM-1 |
| 1.3.6.1.4.1.36.2.15.3.3.4.2.1.1.3 | ColumnaglInterfaceSonetTiming | read-write | mandatory | Specifies whether the PHY operates in loop-timing or local-timing mode. In loop-timing, the recovered clock from the receive signal is used directly to time tr… |
| 1.3.6.1.4.1.36.2.15.3.3.4.3 | NodeaglDS3E3 | |||
| 1.3.6.1.4.1.36.2.15.3.3.4.3.1 | TableaglInterfaceDS3E3Table | not-accessible | mandatory | This table contains the AGL specific interface configuration parameters for the DS3/E3 physical layer. |
| 1.3.6.1.4.1.36.2.15.3.3.4.3.1.1 | RowaglInterfaceDS3E3Entry | not-accessible | mandatory | This list contains DS3/E3 interface configuration parameters and state variables. |
| 1.3.6.1.4.1.36.2.15.3.3.4.3.1.1.1 | ColumnaglInterfaceDS3E3Index | read-only | mandatory | The value of this object identifies the AGL port interface for which this entry contains management information and is the same as aglInterfaceIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.4.3.1.1.2 | ColumnaglInterfaceDS3E3Mode | read-write | mandatory | Specifies whether the DS3/E3 PHY operates in low power mode for short distances or high power mode for longer distances. The following code points are used: 1 … |
| 1.3.6.1.4.1.36.2.15.3.3.4.3.1.1.3 | ColumnaglInterfaceDS3E3Plcp | read-write | mandatory | Specifies whether ATM cells may be mapped into the DS3 PLCP. In the enabled mode, PLCP framing and timing is applied to each ATM cell. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4 | NodeaglAtm | |||
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1 | TableaglVCConnectionTable | not-accessible | mandatory | This table contains AGL ATM VCC configuration and performance parameters and state variables. Each entry represents a bidirectional traffic flow. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1 | RowaglVCConnectionTableEntry | not-accessible | mandatory | A bidirectional circuit. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.1 | ColumnaglVCConnectionPortA | read-only | mandatory | The value of this object identifies the AGL ATM port A of the VCC segment for FDDI-bridged and ATM-to-ATM circuit types. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.2 | ColumnaglVCConnectionPortAVpi | read-only | mandatory | The VPI value at port A for the bidirectional circuit. The maximum VPI value cannot exceed the number supported by the atmInterfaceMaxVpiBits at AGL ATM port A… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.3 | ColumnaglVCConnectionPortAVci | read-only | mandatory | The VCI value at the port A for the bidirectional circuit. The VCI values from 0 to 31 are reserved. The maximum VCI value cannot exceed the number supported b… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.4 | ColumnaglVCConnectionPortB | read-only | mandatory | The value of this object identifies the AGL ATM port B of the VCC segment for ATM-to-ATM circuit types. For FDDI-bridged circuit types this value should be zer… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.5 | ColumnaglVCConnectionPortBVpi | read-only | mandatory | The VPI value at port B for the bidirectional ATM-to-ATM circuit. The maximum VPI value cannot exceed the number supported by the atmInterfaceMaxVpiBits at AGL… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.6 | ColumnaglVCConnectionPortBVci | read-only | mandatory | The VCI value at the port B for the bidirectional ATM-to-ATM circuit. The VCI values from 0 to 31 are reserved. The maximum VCI value cannot exceed the number … |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.7 | ColumnaglVCConnectionTableEntryStatus | read-write | mandatory | The status column used for creating, and deleting bidirectional circuit entries in the agl virtual channel connection table. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.8 | ColumnaglVCConnectionTrafficType | read-write | mandatory | The value of this object identifies the circuit type and characteristics of a particular circuit. There are two types of connections supported: 1. FDDI-bridged… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.9 | ColumnaglVCConnectionAALType | read-write | mandatory | The value of this object identifies the AAL type that should be used on a particular circuit. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.10 | ColumnaglVCConnectionOperStatus | read-only | mandatory | This object indicates the operational status of the VCC, i.e., whether the managed VCC segment is up or down. In the down state, no cells can get across this V… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.11 | ColumnaglVCConnectionAdminStatus | read-write | mandatory | This object indicates the desired status of the VCC, i.e., whether the managed VCC segment is enabled or disabled. In the disabled state, no cells can be passe… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.12 | ColumnaglVCConnectionTrafficShaperPeakRate | read-write | mandatory | The value of this object specifies the peak rate in cells/s that should be used on a particular circuit. The peak rate will be set to a multiple of the aglInte… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.13 | ColumnaglVCConnectionTrafficShaperAvgRate | read-write | mandatory | The value of this object specifies the average (sustained) rate in cells/s that should be used on a particular circuit. The average rate must be less than or e… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.14 | ColumnaglVCConnectionTrafficShaperMinGuaranteedRate | read-write | mandatory | The value of this object specifies the minimum guaranteed rate in cells/s that should be used on a particular circuit. For VBR traffic AGL allows the possibili… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.15 | ColumnaglVCConnectionTrafficShaperPriority | read-write | mandatory | The value of this object specifies the priority which should be given to this circuit in assigning opportunistic bandwidth that arises from AGL's bandwidth ove… |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.2 | TableaglInterfaceATMTable | not-accessible | mandatory | This table contains AGL ATM interface specific settable parameters. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.2.1 | RowaglInterfaceATMTableEntry | not-accessible | mandatory | The list of settable parameters. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.2.1.1 | ColumnaglInterfaceATMIndex | read-write | mandatory | The value of this object identifies the AGL port interface for which this entry contains management information and is the same as aglInterfaceIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.2.1.2 | ColumnaglInterfaceATMScrambeStatus | read-write | mandatory | This object indicates the desired status of the cell scramble module. In the enabled state, outgoing cells are scrambed and input cells are descrambled. |
| 1.3.6.1.4.1.36.2.15.3.3.4.4.2.1.3 | ColumnaglInterfaceATMOAMStatus | read-write | mandatory | This object indicates the desired status of the OAM module in the default circuit. In the enabled state, normal OAM cells are exchanged between the peers. |
| 1.3.6.1.4.1.36.2.15.3.3.5 | NodeaglatmMIB | |||
| 1.3.6.1.4.1.36.2.15.3.3.5.1 | NodeaglatmMIBObjects | |||
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1 | NodeaglatmInterfaceTrafficEnforcementTypes | |||
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.1 | ScalaraglatmInterfaceNoTrafficEnforcement | read-only | mandatory | This identifies the no ATM traffic enforcement type. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.2 | ScalaraglatmInterfaceTrafficEnforcementType1 | read-only | mandatory | This identifies the ATM traffic enforcement type is 1. For type 1 traffic enforcement, parameter 1 specifies CLP=0+1 peak traffic. Parameters 2, 3, 4 and 5 are… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.3 | ScalaraglatmInterfaceTrafficEnforcementType2 | read-only | mandatory | This identifies the ATM traffic enforcement type is 2. For type 2 traffic enforcement, parameter 1 specifies CLP=0 peak traffic and parameter 2 specifies CLP=0… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.4 | ScalaraglatmInterfaceTrafficEnforcementType3 | read-only | mandatory | This identifies the ATM traffic enforcement type is 3. For type 3 traffic enforcement, parameter 1 specifies CLP=0+1 peak traffic, parameter 2 specifies CLP=0 … |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.5 | ScalaraglatmInterfaceTrafficEnforcementType4 | read-only | mandatory | This identifies the ATM traffic enforcement type is 4. For type 4 traffic enforcement, parameter 1 specifies CLP=0 peak traffic, parameter 2 specifies CLP=0+1 … |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.6 | ScalaraglatmInterfaceTrafficEnforcementType5 | read-only | mandatory | This identifies the ATM traffic enforcement type is 5. For type 5 traffic enforcement, parameter 1 specifies CLP=0+1 peak traffic, parameter 2 specifies CLP=0 … |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.7 | ScalaraglatmInterfaceTrafficEnforcementType6 | read-only | mandatory | This identifies the ATM traffic enforcement type is 6. For type 6 traffic enforcement, parameter 1 specifies CLP=0+1 peak traffic, parameter 2 specifies CLP=0+… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.1.8 | ScalaraglatmInterfaceTrafficEnforcementType7 | read-only | mandatory | This identifies the ATM traffic enforcement type is 7. For type 7 traffic enforcement, parameter 1 specifies CLP=0+1 peak traffic and parameter 2 specifies bes… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2 | TableaglatmInterfaceConfTable | not-accessible | mandatory | This table contains ATM local interface configuration parameters and state variables, one entry per ATM interface port. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1 | RowaglatmInterfaceConfEntry | not-accessible | mandatory | This list contains ATM interface configuration parameters and state variables. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.1 | ColumnaglatmInterfaceIndex | not-accessible | mandatory | The value of this object identifies the ATM port interface for which this entry contains management information. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.2 | ColumnaglatmInterfaceMaxVpcs | read-only | mandatory | The maximum number of VPCs supported at this ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.3 | ColumnaglatmInterfaceMaxVccs | read-only | mandatory | The maximum number of VCCs supported at the ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.4 | ColumnaglatmInterfaceConfVpcs | read-only | mandatory | The number of VPCs configured for use at this ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.5 | ColumnaglatmInterfaceConfVccs | read-only | mandatory | The number of VCCs configured for use at the ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.6 | ColumnaglatmInterfaceMaxActiveVpiBits | read-only | mandatory | The maximum number of active VPI bits configured for use at the ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.7 | ColumnaglatmInterfaceMaxActiveVciBits | read-only | mandatory | The maximum number of active VCI bits configured for use at this ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.8 | ColumnaglatmInterfaceIlmiVpiVci | read-only | mandatory | The decimal value of the three octet VPI/VCI field that identifies the VCC supporting the ILMI at the ATM interface. If the value of this object is greater tha… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.9 | ColumnaglatmInterfaceSpecific | read-only | mandatory | This object points to the additional information specific to ATM interfaces. For example, if Enterprise specific objects have been defined in addition to this … |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.3 | TableaglatmInterfaceDs3PlcpTable | not-accessible | mandatory | This table contains ATM interface DS3 PLCP parameters and state variables, one entry per ATM interface port. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.3.1 | RowaglatmInterfaceDs3PlcpEntry | not-accessible | mandatory | This list contains DS3 PLCP parameters and state variables at the ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.1 | ColumnaglatmInterfaceDs3PlcpIndex | not-accessible | mandatory | The value of this object identifies the ATM interface port for which this entry contains management information and is the same as the atmInterfaceIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.2 | ColumnaglatmInterfaceDs3PlcpSEFSs | read-only | mandatory | A DS3 Severely Errored Framing Second (SEFS) is a count of one-second intervals containing one or more SEF event. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.3 | ColumnaglatmInterfaceDs3PlcpAlarmState | read-only | mandatory | This variable indicates if there is an alarm present for the DS3 PLCP. The value receivedFarEndAlarm means that the DS3 PLCP has received an incoming Yellow Si… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.4 | ColumnaglatmInterfaceDs3PlcpUASs | read-only | mandatory | The counter associated with the number of Unavailable Seconds encountered by the PLCP. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.4 | TableaglatmInterfaceSonetTCTable | not-accessible | mandatory | This table contains ATM interface SONET TC Sublayer parameters and state variables, one entry per ATM interface port. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.4.1 | RowaglatmInterfaceSonetTCEntry | not-accessible | mandatory | This list contains SONET TC Sublayer parameters and state variables at the ATM interface. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.4.1.1 | ColumnaglatmInterfaceSonetTCIndex | not-accessible | mandatory | The value of this object identifies the ATM interface port for which this entry contains management information and is the same as the atmInterfaceIndex. |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.4.1.2 | ColumnaglatmInterfaceSonetTCOCDEvents | read-only | mandatory | The number of times the Out of Cell Delineation (OCD) events occur. If seven consecutive ATM cells have Header Error Control (HEC) violations, an OCD event occ… |
| 1.3.6.1.4.1.36.2.15.3.3.5.1.4.1.3 | ColumnaglatmInterfaceSonetTCAlarmState | read-only | mandatory | This variable indicates if there is an alarm present for the SONET TC Sublayer. The value lcdFailure indicates that a Loss of Cell Delineation (LCD) failure st… |
| 1.3.6.1.4.1.36.2.15.3.3.6 | NodeaglsonetMIB | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.1 | NodeaglsonetObjects | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1 | NodeaglsonetMedium | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1 | TableaglsonetMediumTable | not-accessible | mandatory | The SONET/SDH Medium table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1 | RowaglsonetMediumEntry | not-accessible | mandatory | An entry in the SONET/SDH Medium table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.1 | ColumnaglsonetMediumIfIndex | not-accessible | mandatory | An index value that uniquely identifies a SONET/SDH Medium/Section/Line Interface. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.2 | ColumnaglsonetMediumType | read-only | mandatory | This variable identifies whether a SONET or a SDH signal is used across this interface. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.3 | ColumnaglsonetMediumTimeElapsed | read-only | mandatory | The number of seconds, including partial seconds, that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.4 | ColumnaglsonetMediumValidIntervals | read-only | mandatory | The number of previous intervals for which valid data has been stored. A SONET device must support at least n intervals. The minimum value of n is 4. The defau… |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.5 | ColumnaglsonetMediumLineCoding | read-only | mandatory | This variable describes the line coding for this interface. The B3ZS and CMI are used for electrical SONET/SDH signals (STS-1 and STS-3). The Non-Return to Zer… |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.6 | ColumnaglsonetMediumLineType | read-only | mandatory | This variable describes the line type for this interface. The line types are Short and Long Range Single Mode fiber or Multi-Mode fiber interfaces, and coax an… |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.7 | ColumnaglsonetMediumCircuitIdentifier | read-only | mandatory | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2 | NodeaglsonetSection | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1 | TableaglsonetSectionCurrentTable | not-accessible | mandatory | The SONET/SDH Section Current table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1 | RowaglsonetSectionCurrentEntry | not-accessible | mandatory | An entry in the SONET/SDH Section Current table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.1 | ColumnaglsonetSectionCurrentIfIndex | not-accessible | mandatory | The index value which uniquely identifies the SONET/SDH Medium/Section/Line Interface. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.2 | ColumnaglsonetSectionCurrentStatus | read-only | mandatory | This variable indicates the status of the interface. The sonetSectionStatus is a bit map represented as a sum, therefore, it can represent multiple defects sim… |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.3 | ColumnaglsonetSectionCurrentESs | read-only | mandatory | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.4 | ColumnaglsonetSectionCurrentSESs | read-only | mandatory | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.5 | ColumnaglsonetSectionCurrentSEFSs | read-only | mandatory | The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.6 | ColumnaglsonetSectionCurrentCVs | read-only | mandatory | The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3 | NodeaglsonetLine | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1 | TableaglsonetLineCurrentTable | not-accessible | mandatory | The SONET/SDH Line Current table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1 | RowaglsonetLineCurrentEntry | not-accessible | mandatory | An entry in the SONET/SDH Line Current table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.1 | ColumnaglsonetLineCurrentIfIndex | not-accessible | mandatory | The index value which uniquely identifies the SONET/SDH Medium/Line Interface. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.2 | ColumnaglsonetLineCurrentStatus | read-only | mandatory | This variable indicates the status of the interface. The sonetLineStatus is a bit map represented as a sum, therefore, it can represent multiple defects simult… |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.3 | ColumnaglsonetLineCurrentESs | read-only | mandatory | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.4 | ColumnaglsonetLineCurrentSESs | read-only | mandatory | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.5 | ColumnaglsonetLineCurrentCVs | read-only | mandatory | The counter associated with the number of Coding Violations encountered by a SONET/SDH Line in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.6 | ColumnaglsonetLineCurrentUASs | read-only | mandatory | The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2 | NodeaglsonetObjectsPath | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1 | NodeaglsonetPath | |||
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1 | TableaglsonetPathCurrentTable | not-accessible | mandatory | The SONET/SDH Path Current table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1 | RowaglsonetPathCurrentEntry | not-accessible | mandatory | An entry in the SONET/SDH Path Current table. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.1 | ColumnaglsonetPathCurrentIfIndex | not-accessible | mandatory | An index value that uniquely identifies a SONET/SDH Path Interface. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.2 | ColumnaglsonetPathCurrentWidth | read-write | mandatory | A value that indicates the type of the SONET/SDH Path. For SONET, the assigned types are the STS-Nc SPEs, where N = 1, 3, 12, 24, and 48. STS-1 is equal to 51.… |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.3 | ColumnaglsonetPathCurrentStatus | read-only | mandatory | This variable indicates the status of the interface. The sonetPathStatus is a bit map represented as a sum, therefore, it can represent multiple defects simult… |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.4 | ColumnaglsonetPathCurrentESs | read-only | mandatory | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.5 | ColumnaglsonetPathCurrentSESs | read-only | mandatory | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.6 | ColumnaglsonetPathCurrentCVs | read-only | mandatory | The counter associated with the number of Coding Violations encountered by a SONET/SDH Path in the current 15 minute interval. |
| 1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.7 | ColumnaglsonetPathCurrentUASs | read-only | mandatory | The counter associated with the number of Unavailable Seconds encountered by a Path in the current 15 minute, interval. |
| 1.3.6.1.4.1.36.2.18 | NodedecMIBextension | |||
| 1.3.6.1.4.1.36.2.18.1 | Nodeelanext | |||
| 1.3.6.1.4.1.36.2.18.1.1 | Nodeefddi | |||
| 1.3.6.1.4.1.36.2.18.1.1.1 | NodeefddiSMT | |||
| 1.3.6.1.4.1.36.2.18.1.1.1.1 | TableefddiSMTTable | not-accessible | mandatory | A list of SMT entries. The number of entries is given by smtNumber, defined in the FDDI MIB. |
| 1.3.6.1.4.1.36.2.18.1.1.1.1.1 | RowefddiSMTEntry | not-accessible | mandatory | A collection of objects containing information for a given SMT link. |
| 1.3.6.1.4.1.36.2.18.1.1.1.1.1.1 | ColumneSMTIndex | read-only | mandatory | Identifies the SMT Index. The value of this object is the same as the snmpFddiSMTIndex, defined in the FDDI MIB, for this smt entity. |
| 1.3.6.1.4.1.36.2.18.1.1.1.1.1.2 | ColumneSMTStationType | read-only | mandatory | The Station Type Identification. |
| 1.3.6.1.4.1.36.2.18.1.1.1.1.1.3 | ColumneSMTTracesReceived | read-only | mandatory | The number of PC Traces received by this station. |
| 1.3.6.1.4.1.36.2.18.1.1.2 | NodeefddiMAC | |||
| 1.3.6.1.4.1.36.2.18.1.1.2.1 | TableefddiMACTable | not-accessible | mandatory | A list of MAC entries. The number of entries is given by macNumber, defined in the FDDI MIB. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1 | RowefddiMACEntry | not-accessible | mandatory | A collection of objects containing information for a given MAC entity. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.1 | ColumneMACSMTIndex | read-only | mandatory | The value of the SMT index associated with this MAC. The value of this object is the same as the snmpFddiMACSMTIndex, defined in the FDDI MIB, for this MAC ent… |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.2 | ColumneMACIndex | read-only | mandatory | Identifies the MAC Index. The value of this object is the same as the snmpFddiMACIndex, defined in the FDDI MIB, for this MAC entity. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.3 | ColumneMACLinkIndex | read-only | mandatory | The SMT Resource Index. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.4 | ColumneMACLinkState | read-only | mandatory | The current state of the link. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.5 | ColumneMACRingPurgerState | read-only | mandatory | The current Ring Purger state. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.6 | ColumneMACRingPurgerEnable | read-write | mandatory | If true, this Link will participate in the Ring Purger Election and, if elected, perform the Ring Purger function. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.7 | ColumneMACRingPurgeErrors | read-only | mandatory | The number of times the MAC PurgeError Event bit was set. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.8 | ColumneMACFrameStripMode | read-only | mandatory | Method of frame removal used by this station. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.9 | ColumneMACFCIStripErrors | read-only | mandatory | The number of times a Frame Content Independent Strip operation was terminated by receipt of a token. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.10 | ColumneMACRingErrorReason | read-only | mandatory | Reason for last ring disturbance. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.11 | ColumneMACRingInitializationsInitiated | read-only | mandatory | Number of Ring Claim Processes initiated by this link entity. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.12 | ColumneMACRingInitializationsReceived | read-only | mandatory | Number of Ring Claim Processes or Ring Beaconing Processes initiated by a remote link entity and detected by this link entity. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.13 | ColumneMACRingBeaconingInitiated | read-only | mandatory | The number of Ring Beacon Processes initiated by this link entity. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.14 | ColumneMACDuplicateAddressTestFailures | read-only | mandatory | The number of times the duplicate address test failed. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.15 | ColumneMACDuplicateTokensDetected | read-only | mandatory | The number of times this link entity detected a duplicate token. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.16 | ColumneMACUpstreamNbrDuplAddressFlag | read-only | mandatory | The upstream neighbor's duplicate address status, as reported by the NIF frame. Unknown if no NIF frame has been received yet. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.17 | ColumneMACTracesInitiated | read-only | mandatory | The number of PC Traces initiated by this station. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.18 | ColumneMACRestrictedTokenTimeout | read-write | mandatory | The restricted token timeout, which limits how long a single restricted mode dialog may last before being terminated. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.19 | ColumneMACFrameStatusErrors | read-only | mandatory | The number of frames received on the line that had the E (error detected) indicator set or a missing E indicator. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.20 | ColumneMACFrameAlignmentErrors | read-only | mandatory | The number of frames received on the line that contained an odd number of symbols; that is, a non-integral number of octets. |
| 1.3.6.1.4.1.36.2.18.1.1.2.1.1.21 | ColumneMACTransmitUnderruns | read-only | mandatory | The number of times an underrun occured because the device's transmit FIFO became empty due to insufficient memory. In other words, the device was trying to tr… |
| 1.3.6.1.4.1.36.2.18.1.1.3 | NodeefddiPORT | |||
| 1.3.6.1.4.1.36.2.18.1.1.3.1 | TableefddiPORTTable | not-accessible | mandatory | A list of PORT entries. The number of entries is given by portNumber, defined in the FDDI MIB. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1 | RowefddiPORTEntry | not-accessible | mandatory | A collection of objects containing information for a given PORT entity. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.1 | ColumnePORTSMTIndex | read-only | mandatory | The value of the SMT index associated with this port. The value of this object is the same as the snmpFddiPORTSMTIndex, defined in the FDDI MIB, for this PORT … |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.2 | ColumnePORTIndex | read-only | mandatory | Identifies the PORT Index. The value of this object is the same as the snmpFddiPORTIndex, defined in the FDDI MIB, for this PORT entity. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.3 | ColumnePORTPHYIndex | read-only | mandatory | The SMT Resource index. Index of the PHY resource used to identify the PHY PORT in ANSI SMT frames. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.4 | ColumnePORTPMDType | read-only | mandatory | The physical media type of the PORT. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.5 | ColumnePORTPHYState | read-only | mandatory | The PHY state. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.6 | ColumnePORTRejectReason | read-only | mandatory | The current reject reason. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.7 | ColumnePORTConnectionsCompleted | read-only | mandatory | The number of Physical Connections established for this PHY PORT. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.8 | ColumnePORTTNEExpRejects | read-only | mandatory | The number of times a physical disconnection took place because the TNE Noise Timer expired. |
| 1.3.6.1.4.1.36.2.18.1.1.3.1.1.9 | ColumnePORTElasticityBufferErrors | read-only | mandatory | The number of ELM Chip EBUFF_ERROR events. |
| 1.3.6.1.4.1.36.2.18.1.1.4 | NodeefddiFDX | |||
| 1.3.6.1.4.1.36.2.18.1.1.4.1 | TableefddiFDXTable | not-accessible | mandatory | A list of FDX entries. |
| 1.3.6.1.4.1.36.2.18.1.1.4.1.1 | RowefddiFDXEntry | not-accessible | mandatory | A collection of objects containing information for a given FDX MAC entity. |
| 1.3.6.1.4.1.36.2.18.1.1.4.1.1.1 | ColumneFDXSMTIndex | read-only | mandatory | The value of the SMT index associated with this FDX MAC. |
| 1.3.6.1.4.1.36.2.18.1.1.4.1.1.2 | ColumneFDXMACIndex | read-only | mandatory | The value of the MAC index associated with this FDX MAC. |
| 1.3.6.1.4.1.36.2.18.1.1.4.1.1.3 | ColumneFDXEnable | read-write | mandatory | When true, this link will participate in the full duplex auto-configuration and, if this is successful, will operate in the full duplex mode. |
| 1.3.6.1.4.1.36.2.18.1.1.4.1.1.4 | ColumneFDXOp | read-only | mandatory | When true, this link is operating in the full duplex mode. |
| 1.3.6.1.4.1.36.2.18.1.1.4.1.1.5 | ColumneFDXState | read-only | mandatory | The state of the full duplex Control process. |
| 1.3.6.1.4.1.36.2.18.1.2 | Nodeesystem | |||
| 1.3.6.1.4.1.36.2.18.1.2.1 | NodeesysChar | |||
| 1.3.6.1.4.1.36.2.18.1.2.1.1 | ScalaresysRomVersion | read-only | mandatory | The version number of the software stored in ROM. |
| 1.3.6.1.4.1.36.2.18.1.2.1.2 | ScalaresysInitSwitch | read-write | mandatory | This object allows the management action of initializing a device and forcing it to run selftest. It can also be used to reset all information added to the dev… |
| 1.3.6.1.4.1.36.2.18.1.2.1.3 | ScalaresysResetDefaultsSwitch | read-only | mandatory | This object is the state of a hardware switch which, when true, causes the device to reset its parameters to the factory defaults when initialized. |
| 1.3.6.1.4.1.36.2.18.1.2.1.4 | ScalaresysGatewayAddress | read-write | mandatory | This object allows the setting of a default gateway address for this device. |
| 1.3.6.1.4.1.36.2.18.1.2.1.5 | TableesysTrapAddressTable | not-accessible | mandatory | A table of IP Addresses to which this device will send traps. |
| 1.3.6.1.4.1.36.2.18.1.2.1.5.1 | RowesysTrapEntry | not-accessible | mandatory | Each entry contains an IP Address to which all SNMP Traps will be sent by this device. |
| 1.3.6.1.4.1.36.2.18.1.2.1.5.1.1 | ColumnesysTrapAddress | read-write | mandatory | An IP Address to which all SNMP traps generated by this device will be sent. |
| 1.3.6.1.4.1.36.2.18.1.2.1.6 | ScalaresysUpdateSwitch | read-write | mandatory | A software switch that, when set to true, instructs the device to accept a down-line loaded firmware upgrade. If false, the device will not accept upgrades. |
| 1.3.6.1.4.1.36.2.18.1.2.1.7 | ScalaresysLastLoadHost | read-only | mandatory | The physical address of the last host, if any, that responded to the device's request for a downline load of software. |
| 1.3.6.1.4.1.36.2.18.1.2.2 | NodeesysStatus | |||
| 1.3.6.1.4.1.36.2.18.1.2.2.1 | ScalaresysDeviceState | read-only | mandatory | The operational state of the device. |
| 1.3.6.1.4.1.36.2.18.1.2.2.2 | ScalaresysDeviceBrokenReason | read-only | mandatory | The reason that the Device State is BROKEN. If current state is not BROKEN and the Unsolicited Resets counter is nonzero, this object show reason for last fail… |
| 1.3.6.1.4.1.36.2.18.1.2.2.3 | ScalaresysNvramFailed | read-only | mandatory | A flag, that, when set to True, indicates that the NVRAM failed selftest following the last initialization of the device. |
| 1.3.6.1.4.1.36.2.18.1.2.3 | NodeesysCounters | |||
| 1.3.6.1.4.1.36.2.18.1.2.3.1 | ScalaresysPowerups | read-only | mandatory | The number of times this device was powered on. Power Ups, Management Resets and Unsolicited Resets are all mutually exclusive. |
| 1.3.6.1.4.1.36.2.18.1.2.3.2 | ScalaresysMgmtResets | read-only | mandatory | Number of times the device was initialized with a management command using esysInitSwitch. Power Ups, Management Resets and Unsolicited Resets are all mutually… |
| 1.3.6.1.4.1.36.2.18.1.2.3.3 | ScalaresysUnsolicitedResets | read-only | mandatory | Number of times the device initialized itself after encountering a fatal error. Power Ups, Management Resets and Unsolicited Resets are all mutually exclusive. |
| 1.3.6.1.4.1.36.2.18.1.2.4 | NodeesysConcConfig | |||
| 1.3.6.1.4.1.36.2.18.1.2.4.1 | TableesysFRUConfigTable | not-accessible | mandatory | A list of configuration table entries. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1 | RowesysFRUConfigEntry | not-accessible | mandatory | A collection of objects containing information for a given configuration entry. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1.1 | ColumnesysFRUIndex | read-only | mandatory | This object is used for indexing the FRU configuration table. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1.2 | ColumnesysFRUSlot | read-only | mandatory | The physical slot number in which the module resides, if applicable. If not applicable, this is reported as '0'. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1.3 | ColumnesysFRUDesc | read-only | mandatory | A textual description of this FRU. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1.4 | ColumnesysFRUType | read-only | mandatory | Integer representation for the FRU type. This is the machine-readable form of the descriptor object. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1.5 | ColumnesysFRURev | read-only | mandatory | This object represents the FRU revision number. |
| 1.3.6.1.4.1.36.2.18.1.2.4.1.1.6 | ColumnesysFRUState | read-only | mandatory | The operational state of the FRU, if present. |
| 1.3.6.1.4.1.36.2.18.1.2.4.2 | ScalaresysFddiPortTrapSwitch | read-write | mandatory | This is a switch to enable or diable FDDI port up and port down traps. When set to true, the concentrator will send a trap when one of its ports comes up or go… |
| 1.3.6.1.4.1.36.2.18.1.3 | Nodeeinterfaces | |||
| 1.3.6.1.4.1.36.2.18.1.3.1 | TableeifTable | not-accessible | mandatory | A list of interface entries. The number of entries is given by ifNumber, defined in MIB-II. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1 | RoweifEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1.1 | ColumneifIndex | read-only | mandatory | Identifies the Interface. The value of this object is the same as the ifIndex, defined in MIB-II, for this interface. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1.2 | ColumneifBadFramesReceived | read-only | mandatory | Number of frames received with a bad frame check sequence. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1.3 | ColumneifReceiveOverrun | read-only | mandatory | Number of times that the device received a frame loss indication from the hardware on the interface. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1.4 | ColumneifOversizeFrames | read-only | mandatory | Number of frames received on the interface that were larger than the maximum legal size. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1.5 | ColumneifTransmitFramesError | read-only | mandatory | Number of frames that were transmitted with an error on the line. |
| 1.3.6.1.4.1.36.2.18.1.3.1.1.6 | ColumneifMgmtSetsAllowedSwitch | read-only | mandatory | This hardware switch, when true, allows write access to the device. This object has meaning only when the corresponding functionality is present. |
| 1.3.6.1.4.1.36.2.18.1.4 | Nodeebridge | |||
| 1.3.6.1.4.1.36.2.18.1.4.1 | NodeebrChar | |||
| 1.3.6.1.4.1.36.2.18.1.4.1.1 | ScalarebrLB100SpanningTreeVer | read-only | mandatory | The version number of the Spanning Tree algorithm used by the bridge when in the LAN Bridge 100 Spanning Tree mode. |
| 1.3.6.1.4.1.36.2.18.1.4.1.2 | Scalarebr802SpanningTreeVer | read-only | mandatory | The version number of the Spanning Tree algorithm used by the bridge when in the 802.1d Spanning Tree mode. |
| 1.3.6.1.4.1.36.2.18.1.4.1.3 | ScalarebrMaxForwardingDBEntries | read-only | mandatory | The maximum number of address entries that the bridge can store in its volatile memory. |
| 1.3.6.1.4.1.36.2.18.1.4.1.4 | ScalarebrMaxNVForwardingDBEntries | read-only | mandatory | The maximum number of permanent address entries that the bridge canstore in its NVRAM. |
| 1.3.6.1.4.1.36.2.18.1.4.1.5 | ScalarebrMaxProtocolDBEntries | read-only | mandatory | The maximum number of protocol entries that the bridge can store in its protocol database. These entries control the handling of frames based on their Ethernet… |
| 1.3.6.1.4.1.36.2.18.1.4.1.6 | ScalarebrMaxNVProtocolDBEntries | read-only | mandatory | The maximum number of protocol entries that the bridge can store in its nonvolatile memory. These are retained after a power-down. |
| 1.3.6.1.4.1.36.2.18.1.4.1.7 | ScalarebrForwardingDBPurgeThreshold | read-only | mandatory | The total number of active and inactive address entries that will trigger a purge of the inactive entries. |
| 1.3.6.1.4.1.36.2.18.1.4.1.8 | ScalarebrPortTestPassedThreshold | read-write | mandatory | The number of consecutive successful self-tests needed before the bridge considers a line to be operational. |
| 1.3.6.1.4.1.36.2.18.1.4.1.9 | ScalarebrPortTestInterval | read-write | mandatory | The interval, in seconds, at which the bridge will run selftests on a line that is in the BROKEN state. |
| 1.3.6.1.4.1.36.2.18.1.4.1.10 | ScalarebrTopologyChangeTimer | read-only | mandatory | The number of seconds remaining, if this is the Root, for which Topology Change will be propagated in Hello messages. Otherwise this value will be reported as … |
| 1.3.6.1.4.1.36.2.18.1.4.1.11 | ScalarebrManualFilterSwitch | read-write | mandatory | A switch that controls address filtering. When true, the bridge purges the learned entries from its forwarding database, stops its learning process, and forwar… |
| 1.3.6.1.4.1.36.2.18.1.4.1.12 | ScalarebrFragmentationSwitch | read-write | mandatory | A switch that controls whether fragmentation is performed by the bridge when a large IP frame is received on a datalink that supports a higer frame size than t… |
| 1.3.6.1.4.1.36.2.18.1.4.1.13 | ScalarebrRemoveMgmtAddress | read-write | mandatory | This object allows the action of removing all management entered addresses from the forwarding database when set to true(2). When read, it returns a value of o… |
| 1.3.6.1.4.1.36.2.18.1.4.1.14 | ScalarebrRemoveMgmtProto | read-write | mandatory | This object allows the action of removing all management entered protocols from the protocol database when set to true(2). When read, it returns a value of oth… |
| 1.3.6.1.4.1.36.2.18.1.4.2 | NodeebrStat | |||
| 1.3.6.1.4.1.36.2.18.1.4.2.1 | ScalarebrCurrForwardingDBEntries | read-only | mandatory | The number of address entries in the bridge's volatile memory. These will be lost upon loss of power. |
| 1.3.6.1.4.1.36.2.18.1.4.2.2 | ScalarebrCurrNVForwardingDBEntries | read-only | mandatory | The number of address entries in the bridge's NVRAM. These will be retained after loss of power. |
| 1.3.6.1.4.1.36.2.18.1.4.2.3 | ScalarebrCurrProtocolDBEntries | read-only | mandatory | The number of protocol entries that are stored in the bridge's protocol database. These control the handling of frames based on their Ethernet protocol type, I… |
| 1.3.6.1.4.1.36.2.18.1.4.2.4 | ScalarebrCurrNVProtocolDBEntries | read-only | mandatory | The number of protocol entries in the bridge's NVRAM. These are retained after a power loss. |
| 1.3.6.1.4.1.36.2.18.1.4.2.5 | ScalarebrMgmtHeardPort | read-only | mandatory | The port on which this command was received. |
| 1.3.6.1.4.1.36.2.18.1.4.2.6 | ScalarebrLB100BeingPolled | read-only | mandatory | The address of the LAN Bridge 100 mode bridge that sent this bridge into the LAN Bridge 100 Spanning Tree mode. If this bridge is the Root, this object indicat… |
| 1.3.6.1.4.1.36.2.18.1.4.2.7 | ScalarebrInactiveForwardingDBEntries | read-only | mandatory | The number of inactive address entries in the bridge's forwarding database. The bridge marks an address entry inactive when the entry is aged out. |
| 1.3.6.1.4.1.36.2.18.1.4.2.8 | ScalarebrTimeSinceForwardingDBPurged | read-only | mandatory | The number of seconds since the bridge cleared the forwarding database of inactive entries. |
| 1.3.6.1.4.1.36.2.18.1.4.2.9 | ScalarebrTimeSinceLastHello | read-only | mandatory | The number of seconds since the bridge last sent a Hello message. |
| 1.3.6.1.4.1.36.2.18.1.4.3 | NodeebrCoun | |||
| 1.3.6.1.4.1.36.2.18.1.4.3.1 | ScalarebrDeviceFramesLost | read-only | mandatory | The number of frames addressed to the bridge itself that the bridge discarded because it did not have sufficient receive buffers available. |
| 1.3.6.1.4.1.36.2.18.1.4.3.2 | ScalarebrSpanningTreeModeChanges | read-only | mandatory | The number of times that the bridge switched from the 802.1d Spanning Tree mode to the LB100 Spanning Tree mode. |
| 1.3.6.1.4.1.36.2.18.1.4.4 | NodeebrSpan | |||
| 1.3.6.1.4.1.36.2.18.1.4.4.1 | ScalarebrBestRootAge | read-only | mandatory | The age, in hundereths of seconds, of the Hello message that established the best root. |
| 1.3.6.1.4.1.36.2.18.1.4.4.2 | ScalarebrTopologyChangeFlag | read-only | mandatory | A flag that indicates whether a Topology Change is currently in effect on the extended LAN. |
| 1.3.6.1.4.1.36.2.18.1.4.4.3 | ScalarebrTellParentFlag | read-only | mandatory | A flag that indicates if the bridge is attempting to propagate a topology change towards the Root. |
| 1.3.6.1.4.1.36.2.18.1.4.4.4 | ScalarebrForwardingDBShortAgingTime | read-write | mandatory | The number of seconds that the bridge keeps learned entries active while a topology change is in effect. |
| 1.3.6.1.4.1.36.2.18.1.4.4.5 | ScalarebrBadHelloLimit | read-write | mandatory | The number of hello intervals during which the bridge receives one or more bad hellos on a line, before the bridge performs a test on the link. A bad Hello mes… |
| 1.3.6.1.4.1.36.2.18.1.4.4.6 | ScalarebrBadHelloResetTimer | read-write | mandatory | The number of Hello intervals without bad Hellos that the bridge will wait before it resets its bad Hello count to zero. |
| 1.3.6.1.4.1.36.2.18.1.4.4.7 | ScalarebrNoFrameInterval | read-write | mandatory | The The number of seconds of inactivity on a line that will cause the bridge to run a test on that line. The bridge considers a line to be inactive if it does … |
| 1.3.6.1.4.1.36.2.18.1.4.4.8 | ScalarebrLB100PollTime | read-write | mandatory | The number of seconds that a Root bridge in LAN Bridge 100 mode waits between polling the LAN Bridge 100 that is keeping it in this mode. This polling is done … |
| 1.3.6.1.4.1.36.2.18.1.4.4.9 | ScalarebrLB100ResponseTimeout | read-write | mandatory | The number of seconds that a Root in LAN Bridge 100 Spanning Tree mode will wait for a response from the LAN Bridge 100 which is keeping it in this mode, befor… |
| 1.3.6.1.4.1.36.2.18.1.4.4.10 | ScalarebrLB100SpanningTreeCompat | read-write | mandatory | A switch that controls the Spanning Tree mode used by the bridge. If in Auto-Select mode, the bridge will go into 802 Spanning Tree mode by default, but will s… |
| 1.3.6.1.4.1.36.2.18.1.4.5 | NodeebrInterfaces | |||
| 1.3.6.1.4.1.36.2.18.1.4.5.1 | TableebrIfTable | not-accessible | mandatory | A list of interface entries. The number of entries is given by ifNumber, defined in MIB-II. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1 | RowebrIfEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.1 | ColumnebrIfIndex | read-only | mandatory | Identifies the Interface. The value of this object is the same as the ifIndex, defined in MIB-II, for this interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.2 | ColumnebrIfLinkBrokenReason | read-only | mandatory | The reason why the link was last broken. A possible internal fault(1) indicates a problem with the bridge line itself, a possible external fault(2), indicates … |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.3 | ColumnebrIfPortRestarts | read-only | mandatory | The number of times the bridge restarted the line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.4 | ColumnebrIfUnknownDAReceived | read-only | mandatory | The number of frames received on this line for which the bridge had no address entry in its forwarding database. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.5 | ColumnebrIfFramesAddrFiltered | read-only | mandatory | The number of frames filtered by the bridge on this port because of address entries in the forwarding database. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.6 | ColumnebrIfMultiFramesFiltered | read-only | mandatory | The number of frames with multicast destination addresses that were received on the line on the line and filtered by the bridge. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.7 | ColumnebrIfFramesProtocolFiltered | read-only | mandatory | The number of frames received on this line that the bridge discarded because of entries set by management in the protocol database. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.8 | ColumnebrIfDeviceFramesSent | read-only | mandatory | The number of frames originating from the bridge itself that were transmitted on this line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.9 | ColumnebrIfDeviceFramesReceived | read-only | mandatory | The number of frames addressed to the bridge itself that were received on this line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.10 | ColumnebrIfDeviceBytesSent | read-only | mandatory | The number of bytes in the frames originating from the bridge that were transmitted on this line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.11 | ColumnebrIfDeviceBytesReceived | read-only | mandatory | The number of bytes in the frames addressed to the bridge itself that were received on this line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.12 | ColumnebrIfDeviceFramesLost | read-only | mandatory | The number of frames received on the line addressed to the bridge itself discarded by the bridge because it did not have internal buffers to store them. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.13 | ColumnebrIfMultiBytesSent | read-only | mandatory | The number of bytes in Multicast Frames sent, as reported in ifOutNUcastPkts, defined in MIB-II. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.14 | ColumnebrIfMultiBytesReceived | read-only | mandatory | The number of bytes in Multicast Frames received, as reported in ifInNUcastPkts, defined in MIB-II. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.15 | ColumnebrIfMultiDeviceFramesSent | read-only | mandatory | The number of frames with multicast destination addresses transmitted by the bridge itself on the line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.16 | ColumnebrIfMultiDeviceFramesReceived | read-only | mandatory | The number of frames with multicast destination addresses received by the bridge itslef on the line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.17 | ColumnebrIfMultiDeviceBytesSent | read-only | mandatory | The number of bytes in ebrIfMultiDeviceFramesSent. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.18 | ColumnebrIfMultiDeviceBytesReceived | read-only | mandatory | The number of bytes in ebrIfMultiDeviceFramesReceived. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.19 | ColumnebrIfBadBytesReceived | read-only | mandatory | The number of bytes in frames received that had a bad frame check sequence. |
| 1.3.6.1.4.1.36.2.18.1.4.5.1.1.20 | ColumnebrIfBadHelloLimitExceeded | read-only | mandatory | The number of times that the Bad Hellos on the line exceeded the Bad Hello limit. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2 | TableebrIfEtherTable | not-accessible | mandatory | A list of interface entries for an Ethernet port. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1 | RowebrIfEtherEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.1 | ColumnebrIfEthIndex | read-only | mandatory | Identifies the Interface. The value of this object is the same as the ifIndex, defined in MIB-II, for this interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.2 | ColumnebrIfEthPhysicalMediumType | read-only | mandatory | The type of physical medium to which this line is attached. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.3 | ColumnebrIfEthCollisionPresenceTestSwitch | read-write | mandatory | A switch that informs the bridge whether the transceiver on this line is using the Collision Presence Test (CPT), commonly known as heartbeat. It must be enabl… |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.4 | ColumnebrIfEthCollisionTestFailed | read-only | mandatory | The number of times that a Collision Presence Test (CPT) signal was not detected within 4 microseconds after a transmission on the line. This counter is valid … |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.5 | ColumnebrIfEthFramingError | read-only | mandatory | The number of times that a frame received on the line contained both a noninteger multiple of 8 bits and a CRC error. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.6 | ColumnebrIfEthLengthError | read-only | mandatory | The number of 802.3 frames received that contained a Length field inconsistent with the actual number of data bytes in the packet. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.7 | ColumnebrIfEthTransmitMultipleCollisions | read-only | mandatory | The number of times that the bridge had to retry transmission of a frame on the line. This was because of collisions during transmission due to congestion on t… |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.8 | ColumnebrIfEthCarrierLoss | read-only | mandatory | The number of times that the bridge detected a loss of the carrier signal while transmitting a frame on the line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.2.1.9 | ColumnebrIfEthCollisionLimitExceeded | read-only | mandatory | The number of times that the bridge failed to transmit a frame on this line after 16 attempts, the collision limit. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3 | TableebrIfFddiTable | not-accessible | mandatory | A list of interface entries for an FDDI port. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1 | RowebrIfFddiEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1.1 | ColumnebrIfFddiIndex | read-only | mandatory | Identifies the Interface. The value of this object is the same as the ifIndex, defined in MIB-II, for this interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1.2 | ColumnebrIfFddiUnprocessedErrorPackets | read-only | mandatory | The number of times that an error frame was received on thisline but the bridge did not have time to decipher it. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1.3 | ColumnebrIfFddiIpDatagramsFragmented | read-only | mandatory | The number or large IP Datagrams that were fragmented into smaller frames because they did not fit into legal size packets on the smaller datalink after transl… |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1.4 | ColumnebrIfFddiIpDontFragment | read-only | mandatory | The number of large IP datagrams that could not be fragmented because the DONT-FRAGMENT bit was set in the IP header. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1.5 | ColumnebrIfFddiIpIllegalHeaderLength | read-only | mandatory | The number of large IP datagrams that were discarded instead of being fragmented because the IP header was of illegal length. |
| 1.3.6.1.4.1.36.2.18.1.4.5.3.1.6 | ColumnebrIfFddiIpIllegalSize | read-only | mandatory | The number of large IP datagrams that were discarded instead of being fragmented because the IP header indicated a length greater than the number of actual byt… |
| 1.3.6.1.4.1.36.2.18.1.4.5.4 | TableebrIfSpanTable | not-accessible | mandatory | A list of interface entries for an FDDI port. |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1 | RowebrIfSpanEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1.1 | ColumnebrIfSpIndex | read-only | mandatory | Identifies the Interface. The value of this object is the same as the ifIndex, defined in MIB-II, for this interface. |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1.2 | ColumnebrIfSpDesigRootAge | read-only | mandatory | The age, in hundreths of seconds, of the last Hello message received from the designated bridge on the line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1.3 | ColumnebrIfSpForwardDelayTimer | read-only | mandatory | The time remaining, in hundreths of seconds, before the bridge will leave the Preforwarding state (listening or learning), and enter the Forwarding State. If n… |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1.4 | ColumnebrIfSpBadHelloCount | read-only | mandatory | The number of Hello intervals during which at least one Bad Hello was received. |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1.5 | ColumnebrIfSpPossibleLoopFlag | read-only | mandatory | A flag that indicates whether the bridge detected a loop condition on this line. |
| 1.3.6.1.4.1.36.2.18.1.4.5.4.1.6 | ColumnebrIfSpTopologyChangeAckFlag | read-only | mandatory | A flag that indicates whether a topology change notification received on a link that we are designated on needs to be acknowledged. |
| 1.3.6.1.4.1.36.2.18.1.4.6 | NodeebrTwoPortStatic | |||
| 1.3.6.1.4.1.36.2.18.1.4.6.1 | TableebrTwoPortStaticTable | not-accessible | mandatory | A table that contains static destination and source address filtering information about unicast and multicast addresses for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.6.1.1 | RowebrTwoPortStaticEntry | not-accessible | mandatory | Information about a specific MAC address for which the bridge has some static forwarding and/or filtering information. |
| 1.3.6.1.4.1.36.2.18.1.4.6.1.1.1 | ColumnebrTwoPortAddress | read-write | mandatory | The destination/source MAC Address in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.6.1.1.2 | ColumnebrTwoPortPortNum | read-write | mandatory | The Port Number to which this address will be locked-down, if the status is lockDown. Otherwise, this field has a value of 0. |
| 1.3.6.1.4.1.36.2.18.1.4.6.1.1.3 | ColumnebrTwoPortStatus | read-write | mandatory | The status of this entry. The meanings of the values are: lockDown(1) : This address is 'locked-down' to the port specified by the ebrTwoPortPortNum field. Thi… |
| 1.3.6.1.4.1.36.2.18.1.4.7 | NodeebrMultiPortStatic | |||
| 1.3.6.1.4.1.36.2.18.1.4.7.1 | TableebrMultiPortStaticTable | not-accessible | mandatory | A table that contains static destination and source address filtering information about unicast and multicast addresses for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.7.1.1 | RowebrMultiPortStaticEntry | not-accessible | mandatory | Information about a specific MAC address for which the bridge has some static forwarding and/or filtering information. |
| 1.3.6.1.4.1.36.2.18.1.4.7.1.1.1 | ColumnebrMultiPortAddress | read-write | mandatory | The destination/source MAC Address in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.7.1.1.2 | ColumnebrMultiPortReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrMultiPortAllowedToGoTo field. A value of zero indicates that this entry applies on all… |
| 1.3.6.1.4.1.36.2.18.1.4.7.1.1.3 | ColumnebrMultiPortAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and sourced from or destined to the address specified by ebrMultiPortAddress are allowed to be f… |
| 1.3.6.1.4.1.36.2.18.1.4.7.1.1.4 | ColumnebrMultiPortPortNum | read-write | mandatory | The Port Number to which this address will be locked-down, if the status is lockDown. Otherwise, this field has a value of zero. |
| 1.3.6.1.4.1.36.2.18.1.4.7.1.1.5 | ColumnebrMultiPortStatus | read-write | mandatory | The status of this entry. The meanings of the values are: portMask(1) : The static filtering for this address is specified by the MultiPortAllowedToGoTo field.… |
| 1.3.6.1.4.1.36.2.18.1.4.8 | NodeebrTwoProtoFilt | |||
| 1.3.6.1.4.1.36.2.18.1.4.8.1 | ScalarebrTwoProtoEnetFilterOther | read-write | mandatory | Action taken by the bridge on Ethernet protocol types other than those specified in the ebrTwoEnetProtoTable. |
| 1.3.6.1.4.1.36.2.18.1.4.8.2 | ScalarebrTwoProtoSapFilterOther | read-write | mandatory | Action taken by the bridge on 802.2 DSAPs other than those specified in the ebrTwoSapProtoTable. |
| 1.3.6.1.4.1.36.2.18.1.4.8.3 | ScalarebrTwoProtoSnapFilterOther | read-write | mandatory | Action taken by the bridge on the 5-byte SNAP PIDs other than those specified in the ebrTwoSnapProtoTable. |
| 1.3.6.1.4.1.36.2.18.1.4.8.4 | TableebrTwoEnetProtoTable | not-accessible | mandatory | A table that contains filtering information about Ethernet protocol types for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.8.4.1 | RowebrTwoEnetProtoEntry | not-accessible | mandatory | A table that contains filtering information about Ethernet protocol types for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.8.4.1.1 | ColumnebrTwoEnetProtoType | read-write | mandatory | The protocol type in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.8.4.1.2 | ColumnebrTwoEnetProtoStatus | read-write | mandatory | Action taken by bridge when it sees this ethernet protocol type in a received frame. The meanings of the values are: forward(1) : Frames received with this pro… |
| 1.3.6.1.4.1.36.2.18.1.4.8.5 | TableebrTwoSapProtoTable | not-accessible | mandatory | A table that contains filtering information about 802.2 SAPs in the DSAP field for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.8.5.1 | RowebrTwoSapProtoEntry | not-accessible | mandatory | A table that contains filtering information about 802.2 SAPs in the DSAP field for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.8.5.1.1 | ColumnebrTwoSapIndex | read-only | mandatory | Index of the SAP table. |
| 1.3.6.1.4.1.36.2.18.1.4.8.5.1.2 | ColumnebrTwoSapValue | read-write | mandatory | The 802.2 DSAP in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.8.5.1.3 | ColumnebrTwoSapStatus | read-write | mandatory | Action taken by bridge when it sees this 802.2 SAP in the DSAP field of a received frame. The meanings of the values are: forward(1) : Frames received with thi… |
| 1.3.6.1.4.1.36.2.18.1.4.8.6 | TableebrTwoSnapProtoTable | not-accessible | mandatory | A table that contains filtering information about 5-byte SNAP PIDs for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.8.6.1 | RowebrTwoSnapProtoEntry | not-accessible | mandatory | A table that contains filtering information about 5-byte SNAP PIDs for 2-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.8.6.1.1 | ColumnebrTwoSnapIndex | read-only | mandatory | The index into the SNAP table. |
| 1.3.6.1.4.1.36.2.18.1.4.8.6.1.2 | ColumnebrTwoSnapValue | read-write | mandatory | The SNAP PID in an 802 frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.8.6.1.3 | ColumnebrTwoSnapStatus | read-write | mandatory | Action taken by bridge when it sees this SNAP PID in a received 802 frame. The meanings of the values are: forward(1) : Frames received with this snap pid are … |
| 1.3.6.1.4.1.36.2.18.1.4.9 | NodeebrMultiProtoFilt | |||
| 1.3.6.1.4.1.36.2.18.1.4.9.1 | TableebrMultiEnetProtoTable | not-accessible | mandatory | A table that contains filtering information about Ethernet protocol types for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.9.1.1 | RowebrMultiEnetProtoEntry | not-accessible | mandatory | A table that contains filtering information about Ethernet protocol types for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.9.1.1.1 | ColumnebrMultiEnetProtoType | read-write | mandatory | The protocol type in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.9.1.1.2 | ColumnebrMultiEnetReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrMultiPortEnetProtoType field. A value of zero indicates that this entry applies on all… |
| 1.3.6.1.4.1.36.2.18.1.4.9.1.1.3 | ColumnebrMultiEnetAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and containing the protocol type specified by ebrMultiEnetProtoType are allowed to be forwarded.… |
| 1.3.6.1.4.1.36.2.18.1.4.9.1.1.4 | ColumnebrMultiEnetStatus | read-write | mandatory | Action taken by bridge when it sees this ethernet protocol type in a received frame. The meanings of the values are: portMask(1) : The static filtering for thi… |
| 1.3.6.1.4.1.36.2.18.1.4.9.2 | TableebrMultiSapProtoTable | not-accessible | mandatory | A table that contains filtering information about 802.2 SAPs in the DSAP field for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.9.2.1 | RowebrMultiSapProtoEntry | not-accessible | mandatory | A table that contains filtering information about 802.2 SAPs in the DSAP field for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.9.2.1.1 | ColumnebrMultiSapValue | read-write | mandatory | The 802.2 DSAP in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.9.2.1.2 | ColumnebrMultiSapReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrMultiPortSapProtoType field. A value of zero indicates that this entry applies on all … |
| 1.3.6.1.4.1.36.2.18.1.4.9.2.1.3 | ColumnebrMultiSapAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and containing the DSAP in an 802 frame specified by ebrMultiSapValue are allowed to be forwarde… |
| 1.3.6.1.4.1.36.2.18.1.4.9.2.1.4 | ColumnebrMultiSapStatus | read-write | mandatory | Action taken by bridge when it sees this 802.2 SAP in the DSAP field of a received frame. The meanings of the values are: portMask(1) : The static filtering fo… |
| 1.3.6.1.4.1.36.2.18.1.4.9.3 | TableebrMultiSnapProtoTable | not-accessible | mandatory | A table that contains filtering information about 5-byte SNAP PIDs for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.9.3.1 | RowebrMultiSnapProtoEntry | not-accessible | mandatory | A table that contains filtering information about 5-byte SNAP PIDs for multi-port bridges. |
| 1.3.6.1.4.1.36.2.18.1.4.9.3.1.1 | ColumnebrMultiSnapValue | read-write | mandatory | The SNAP PID in an 802 frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.36.2.18.1.4.9.3.1.2 | ColumnebrMultiSnapReceivePort | read-write | mandatory | The port from which a frame must be received to use the corresponding ebrMultiPortSnapProtoType field. A value of zero indicates that this entry applies on all… |
| 1.3.6.1.4.1.36.2.18.1.4.9.3.1.3 | ColumnebrMultiSnapAllowedToGoTo | read-write | mandatory | The set of ports to which frames received from a specific port and containing the SNAP PID in an 802 frame specified by ebrMultiSnapValue are allowed to be for… |
| 1.3.6.1.4.1.36.2.18.1.4.9.3.1.4 | ColumnebrMultiSnapStatus | read-write | mandatory | Action taken by bridge when it sees this SNAP PID in a received 802 frame. The meanings of the values are: portMask(1) : The static filtering for this address … |
| 1.3.6.1.4.1.36.2.18.1.4.10 | NodeebrMultiFiltSw | |||
| 1.3.6.1.4.1.36.2.18.1.4.10.1 | TableebrMultiSwTable | not-accessible | mandatory | A list of interface entries. The number of entries is given by ifNumber, defined in MIB-II. |
| 1.3.6.1.4.1.36.2.18.1.4.10.1.1 | RowebrMultiSwEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.1.4.10.1.1.1 | ColumnebrMultiSwIndex | read-only | mandatory | Identifies the Interface to which this entry applies. |
| 1.3.6.1.4.1.36.2.18.1.4.10.1.1.2 | ColumnebrMultiSwManualFilter | read-write | mandatory | A switch that controls address filtering. When true, the bridge purges the learned entries from its forwarding database, stops its learning process, and forwar… |
| 1.3.6.1.4.1.36.2.18.1.4.10.1.1.3 | ColumnebrMultiSwProtoEnetOther | read-write | mandatory | Action taken by the bridge on Ethernet protocol types other than those specified in the ebrMultiEnetProtoTable. |
| 1.3.6.1.4.1.36.2.18.1.4.10.1.1.4 | ColumnebrMultiSwProtoSapOther | read-write | mandatory | Action taken by the bridge on 802.2 DSAPs other than those specified in the ebrMultiSapProtoTable. |
| 1.3.6.1.4.1.36.2.18.1.4.10.1.1.5 | ColumnebrMultiSwProtoSnapOther | read-write | mandatory | Action taken by the bridge on the 5-byte SNAP PIDs other than those specified in the ebrMultiSnapProtoTable. |
| 1.3.6.1.4.1.36.2.18.1.4.11 | NodeebrNTP | |||
| 1.3.6.1.4.1.36.2.18.1.4.11.1 | TableebrNTPTable | not-accessible | mandatory | A table of Ethernet protocol types which will selectively be translated in such a way as to guarantee that the form in which a packet was received - Ethernet P… |
| 1.3.6.1.4.1.36.2.18.1.4.11.1.1 | RowebrNTPEntry | not-accessible | mandatory | A list of NTP protocol type entries. |
| 1.3.6.1.4.1.36.2.18.1.4.11.1.1.1 | ColumnebrNTPtype | read-write | mandatory | A protocol type in the NTP table. |
| 1.3.6.1.4.1.36.2.18.1.4.11.1.1.2 | ColumnebrNTPStatus | read-write | mandatory | Writing invalid(2) to this object removes the corresponding entry. When read, this object always returns a value of other(1). |
| 1.3.6.1.4.1.36.2.18.1.4.11.2 | ScalaresysIPXSwitch | read-write | mandatory | A software switch that, when set to true, causes the bridge to translate IPX 'raw 802.3' packets into SNAP encapsulated packets on the FDDI. Note that this wor… |
| 1.3.6.1.4.1.36.2.18.1.4.12 | NodeebrRateLimiting | |||
| 1.3.6.1.4.1.36.2.18.1.4.12.1 | ScalarebrRateLimitSwitch | read-write | mandatory | By default, rate limiting will be disabled. It can be enabled by setting this object to 'true(1)'. |
| 1.3.6.1.4.1.36.2.18.1.4.12.2 | ScalarebrRateLimit | read-write | mandatory | This is the maximum number of rate-limited frames per second that the bridge will forward per second. |
| 1.3.6.1.4.1.36.2.18.1.4.12.3 | TableebrRateLimitCounterTable | not-accessible | mandatory | A table of the count of frames that were dropped by the bridge due to rate limiting on each port. |
| 1.3.6.1.4.1.36.2.18.1.4.12.3.1 | RowebrRateLimitCounterEntry | not-accessible | mandatory | A list of rate limited frame counter entries. |
| 1.3.6.1.4.1.36.2.18.1.4.12.3.1.1 | ColumnebrRateLimitPort | read-only | mandatory | The port for which this entry contains rate limit counters information. |
| 1.3.6.1.4.1.36.2.18.1.4.12.3.1.2 | ColumnebrRateLimitAddressFrames | read-only | mandatory | This is the number of frames per second that were filtered due to address rate limiting. |
| 1.3.6.1.4.1.36.2.18.1.4.12.3.1.3 | ColumnebrRateLimitProtocolFrames | read-only | mandatory | This is the number of frames per second that were filtered due to protocol rate limiting. |
| 1.3.6.1.4.1.36.2.18.1.5 | Nodeeauth | |||
| 1.3.6.1.4.1.36.2.18.1.5.1 | Nodeeauth1 | |||
| 1.3.6.1.4.1.36.2.18.1.5.1.1 | ScalareauthTrapCommunity | read-write | mandatory | The community string used in SNMP Trap PDUs. |
| 1.3.6.1.4.1.36.2.18.1.5.1.2 | TableeauthTrapUserTable | not-accessible | mandatory | A list of addresses to which traps will be sent and associated information. |
| 1.3.6.1.4.1.36.2.18.1.5.1.2.1 | RoweauthTrapUserEntry | not-accessible | mandatory | Objects containing information for a given trap address. |
| 1.3.6.1.4.1.36.2.18.1.5.1.2.1.1 | ColumneauthTrapUserAddr | read-write | mandatory | An IP Address to which all SNMP Trap messages will be sent. |
| 1.3.6.1.4.1.36.2.18.1.5.1.2.1.2 | ColumneauthTrapUserStatus | read-write | mandatory | Writing invalid(2) to this object removes the corresponding entry. When read, this object always returns a value of other(1). |
| 1.3.6.1.4.1.36.2.18.1.5.1.3 | ScalareauthReadOnlyCommunity | read-write | mandatory | The community string used to identify an SNMP community with access rights of Read-only. |
| 1.3.6.1.4.1.36.2.18.1.5.1.4 | TableeauthReadOnlyUserTable | not-accessible | mandatory | A list of Read-only users and associated information. |
| 1.3.6.1.4.1.36.2.18.1.5.1.4.1 | RoweauthReadOnlyUserEntry | not-accessible | mandatory | Objects containing information for a given Read-only user. |
| 1.3.6.1.4.1.36.2.18.1.5.1.4.1.1 | ColumneauthReadOnlyUserAddr | read-write | mandatory | An IP Address, or a set of IP addresses, which has Read-only SNMP access to this agent. If this object is used as a wildcard, bits corresponding to the zero bi… |
| 1.3.6.1.4.1.36.2.18.1.5.1.4.1.2 | ColumneauthReadOnlyUserMask | read-write | mandatory | A 32-bit mask which is applied to (ANDed with) the source IP address of an incoming SNMP message. If the result of the mask is equal to eauthReadOnlyUserAddr, … |
| 1.3.6.1.4.1.36.2.18.1.5.1.4.1.3 | ColumneauthReadOnlyUserStatus | read-write | mandatory | Writing invalid(2) to this object removes the corresponding entry. When read, this object always returns a value of other(1). |
| 1.3.6.1.4.1.36.2.18.1.5.1.5 | ScalareauthReadWriteCommunity | read-write | mandatory | The community string used to identify an SNMP community with access rights of Read-Write. |
| 1.3.6.1.4.1.36.2.18.1.5.1.6 | TableeauthReadWriteUserTable | not-accessible | mandatory | A list of Read-Write users and associated information. |
| 1.3.6.1.4.1.36.2.18.1.5.1.6.1 | RoweauthReadWriteUserEntry | not-accessible | mandatory | Objects containing information for a given Read-Write user. |
| 1.3.6.1.4.1.36.2.18.1.5.1.6.1.1 | ColumneauthReadWriteUserAddr | read-write | mandatory | An IP Address, or a set of IP addresses, which has Read-Write SNMP access to this agent. If this object is used as a wildcard, bits corresponding to the zero b… |
| 1.3.6.1.4.1.36.2.18.1.5.1.6.1.2 | ColumneauthReadWriteUserMask | read-write | mandatory | A 32-bit mask which is applied to (ANDed with) the source IP address of an incoming SNMP message. If the result of the mask is equal to eauthReadWriteUserAddr,… |
| 1.3.6.1.4.1.36.2.18.1.5.1.6.1.3 | ColumneauthReadWriteUserStatus | read-write | mandatory | Writing invalid(2) to this object removes the corresponding entry. When read, this object always returns a value of other(1). |