DVB-CABLE-INA-IF-MIB
308 objects
The MIB modules for INAs that conform to the EuroModem specification. This MIB assumes the INA implements MIB-II RFC 1213 Pedersen Informational - Expires August 2001 13 DVB Cable INA Interface MIB Feb 2001 The original MIB definition work was carried out for the DVB-RC group by Bert Van Willigen Philips Research Laboratory Eindhoven, The Netherlands.
Imported Objects
| IF-MIB | ifIndex InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 experimental Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE TimeTicks transmission Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.146 | IdentitydvbInaIf | The MIB modules for INAs that conform to the EuroModem specification. This MIB assumes the INA implements MIB-II RFC 1213 Pedersen Informational - Expires Augu… | ||
| 1.3.6.1.2.1.10.146.1 | NodedvbInaIfMIBObjects | |||
| 1.3.6.1.2.1.10.146.1.1 | NodedvbInaIfMac | |||
| 1.3.6.1.2.1.10.146.1.1.1 | TabledvbInaIfMacTable | not-accessible | current | Describes the attributes of each MAC interface, extending the information available from ifEntry. |
| 1.3.6.1.2.1.10.146.1.1.1.1 | RowdvbInaIfMacEntry | not-accessible | current | An entry containing objects describing attributes of each MAC entry, extending the information in ifEntry. An entry in this table exists for each ifEntry with … |
| 1.3.6.1.2.1.10.146.1.1.1.1.1 | ColumndvbInaIfMacDeviceCapabilities | read-only | current | This 32-bit object specifies the maximum capabilities of this MAC entity. This is the possible set of capability for this INA. |
| 1.3.6.1.2.1.10.146.1.1.1.1.2 | ColumndvbInaIfMacDeviceExtendedCapabilities | read-only | current | This 32-bit object specifies the maximum extended capabilities of this MAC entity. This is the possible set of capability for this INA. |
| 1.3.6.1.2.1.10.146.1.1.1.1.3 | ColumndvbInaIfMacCapabilities | read-write | current | This 32-bit object specifies the capabilities of this MAC entity. It is equal to or a subset of dvbInaIfMacDeviceCapabilities. Default this parameter is equal … |
| 1.3.6.1.2.1.10.146.1.1.1.1.4 | ColumndvbInaIfMacExtendedCapabilities | read-write | current | This 32-bit object specifies the extended capabilities of this MAC entity. It is equal to or a subset of dvbInaIfMacDeviceExtendedCapabilities. Default this pa… |
| 1.3.6.1.2.1.10.146.1.1.1.1.5 | ColumndvbInaIfMacProtocolSupport | read-write | current | Specifies the MAC standard version supported by this MAC entity. Optional, this parameter can be written to force a particular MAC version to be executed by th… |
| 1.3.6.1.2.1.10.146.1.1.1.1.6 | ColumndvbInaIfMacTimeout0 | read-write | current | Time-out value 0x0. |
| 1.3.6.1.2.1.10.146.1.1.1.1.7 | ColumndvbInaIfMacTimeout1 | read-write | current | Time-out value 0x1. |
| 1.3.6.1.2.1.10.146.1.1.1.1.8 | ColumndvbInaIfMacTimeout2 | read-write | current | Time-out value 0x2. |
| 1.3.6.1.2.1.10.146.1.1.1.1.9 | ColumndvbInaIfMacTimeout3 | read-write | current | Time-out value 0x3. |
| 1.3.6.1.2.1.10.146.1.1.1.1.10 | ColumndvbInaIfMacTimeout4 | read-write | current | Time-out value 0x4. |
| 1.3.6.1.2.1.10.146.1.1.1.1.11 | ColumndvbInaIfMacTimeoutD | read-write | current | Time-out value 0xD. Terminal Time-Out, Security Sign-On. |
| 1.3.6.1.2.1.10.146.1.1.1.1.12 | ColumndvbInaIfMacTimeoutE | read-write | current | Time-out value 0xE. Terminal Time-Out, Main Key Exchange. |
| 1.3.6.1.2.1.10.146.1.1.1.1.13 | ColumndvbInaIfMacTimeoutF | read-write | current | Time-out value 0xF. Terminal Time-Out, Quick/Explicit Key exchange. |
| 1.3.6.1.2.1.10.146.1.1.1.1.14 | ColumndvbInaIfMacRapidSignOnEnable | read-write | current | This Boolean parameter specifies whether the NIU's are allowed to do a rapid sign-on when they enter the sign-on process. (See the Need_Calibration bit in the … |
| 1.3.6.1.2.1.10.146.1.1.1.1.15 | ColumndvbInaIfMacRespCollTimeWindow | read-write | current | Specifies the maximum time for the sign-on response message transmission randomisation. |
| 1.3.6.1.2.1.10.146.1.1.1.1.16 | ColumndvbInaIfMacAddressFilterUse | read-write | current | This setting controls the use of the of the Address filter in the Sign-On Request Message. Disabled : The address filter is not used. Managed : The manager can… |
| 1.3.6.1.2.1.10.146.1.1.1.1.17 | ColumndvbInaIfMacAddressPositionMask | read-write | current | Indicates the bit positions in the NIU MAC address that are used for address filtering comparison. |
| 1.3.6.1.2.1.10.146.1.1.1.1.18 | ColumndvbInaIfMacAddressComparisonValue | read-write | current | Specifies the value that the NIU should use for MAC address comparison. |
| 1.3.6.1.2.1.10.146.1.1.1.1.19 | ColumndvbInaIfMacGrantProtocolTimeOut | read-write | current | Default value for the time that the NIU should wait before verifying the status of pending grants. See also dvbInaIfNiuGrantProtocolTimeOut. |
| 1.3.6.1.2.1.10.146.1.1.1.1.20 | ColumndvbInaIfMacIdleInterval | read-write | current | Specifies the transmission interval in seconds to be used for the MAC Idle message. When this value is zero, no idle messages shall be sent. |
| 1.3.6.1.2.1.10.146.1.1.1.1.21 | ColumndvbInaIfMacIdleInvalidCount | read-write | current | Specifies a MAC Idle message invalid period in number of dvbInaIfMacIdleInterval, after which the NIU is declared to be signed-off. For example, if dvbInaIfMac… |
| 1.3.6.1.2.1.10.146.1.1.1.1.22 | ColumndvbInaIfMacN | read-write | current | Maximum value of the upstream slot position register. |
| 1.3.6.1.2.1.10.146.1.1.1.1.23 | ColumndvbInaIfMacMaxContentionMsgLen | read-write | current | The default value for the Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted usin… |
| 1.3.6.1.2.1.10.146.1.1.1.1.24 | ColumndvbInaIfMacMaxReservationMsgLen | read-write | current | The default value for the Maximum_Reservation_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted usi… |
| 1.3.6.1.2.1.10.146.1.1.1.1.25 | ColumndvbInaIfMacNiuCount | read-only | current | Number of connected NIUs. |
| 1.3.6.1.2.1.10.146.1.1.1.1.26 | ColumndvbInaIfMacConnections | read-only | current | The number of connections currently active for this MAC entity. |
| 1.3.6.1.2.1.10.146.1.1.1.1.27 | ColumndvbInaIfMacUnknownNiuError | read-only | current | This value is incremented if a message is received from a unknown NIU, except if it is a SignOn_Response Message. |
| 1.3.6.1.2.1.10.146.1.1.1.1.28 | ColumndvbInaIfMacMsgDataError | read-only | current | This value is incremented if a MAC message is received with a data error, i.e. 1) is too short, 2) has an illegal Connection ID or Reservation ID, 3) is a rese… |
| 1.3.6.1.2.1.10.146.1.1.1.1.29 | ColumndvbInaIfMacMsgHdrError | read-only | current | This value is incremented if a MAC message is received with a header error, i.e. 1) is too short, 2) does not contain a MAC address. |
| 1.3.6.1.2.1.10.146.1.1.1.1.30 | ColumndvbInaIfMacInvalidNiu | read-only | current | This value is incremented if a MAC Initialisation Complete Message is transmitted with the Invalid_STB/NIU bit set. |
| 1.3.6.1.2.1.10.146.1.1.1.1.31 | ColumndvbInaIfMacTimingRangingError | read-only | current | This value is incremented if a MAC Initialisation Complete Message is transmitted with the Timing_Ranging_Error bit set. |
| 1.3.6.1.2.1.10.146.1.1.1.1.32 | ColumndvbInaIfMacPowerRangingError | read-only | current | This value is incremented if a MAC Initialisation Complete Message is transmitted with the Power_Ranging_Error bit set. |
| 1.3.6.1.2.1.10.146.1.1.1.1.33 | ColumndvbInaIfMacOtherSignOnError | read-only | current | This value is incremented if a MAC Initialisation Complete Message is transmitted with the Other_Error bit set. |
| 1.3.6.1.2.1.10.146.1.2 | NodedvbInaIfProvision | |||
| 1.3.6.1.2.1.10.146.1.2.1 | TabledvbInaIfProvChTable | not-accessible | current | This table specifies the information for the Default Configuration Message transmitted on the Provisioning channel. |
| 1.3.6.1.2.1.10.146.1.2.1.1 | RowdvbInaIfProvChEntry | not-accessible | current | An entry containing objects describing information for the Default Configuration Message transmitted on the Provisioning channel. More than one downstream can … |
| 1.3.6.1.2.1.10.146.1.2.1.1.1 | ColumndvbInaIfProvChIndex | not-accessible | current | Index of this table entry. |
| 1.3.6.1.2.1.10.146.1.2.1.1.2 | ColumndvbInaIfProvChRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.2.1.1.3 | ColumndvbInaIfProvChServiceChIfIndex | read-create | current | The ifIndex of the upstream channel used as Service Channel for the provisioning. |
| 1.3.6.1.2.1.10.146.1.2.1.1.4 | ColumndvbInaIfProvChBackupServiceChIfIndex | read-create | current | The ifIndex of the upstream channel used as Backup Service Channel for the provisioning. |
| 1.3.6.1.2.1.10.146.1.2.1.1.5 | ColumndvbInaIfProvChIncrPowerRetryCount | read-create | current | Specifies the number of attempts the NIU should do to enter the system at the same power level before incrementing its upstream transmit power for this MAC ent… |
| 1.3.6.1.2.1.10.146.1.2.1.1.6 | ColumndvbInaIfProvChMaxPowerLevel | read-create | current | Specifies the maximum power in dBuV the NIU is allowed to transmit upstream for this MAC entity. |
| 1.3.6.1.2.1.10.146.1.2.1.1.7 | ColumndvbInaIfProvChMinPowerLevel | read-create | current | Specifies the minimum power in dBuV the NIU has to transmit upstream for this MAC entity. |
| 1.3.6.1.2.1.10.146.1.2.1.1.8 | ColumndvbInaIfProvChMaxBackOffExponent | read-create | current | Specifies the maximum back off exponent counter for this MAC entity. |
| 1.3.6.1.2.1.10.146.1.2.1.1.9 | ColumndvbInaIfProvChMinBackOffExponent | read-create | current | Specifies the minimum back off exponent counter for this MAC entity. |
| 1.3.6.1.2.1.10.146.1.2.1.1.10 | ColumndvbInaIfProvChAbsoluteTimeOffset | read-create | current | Specifies the default absolute time offset in 100 ns units to be used for first sign-on of a NIU for this MAC entity. |
| 1.3.6.1.2.1.10.146.1.3 | NodedvbInaIfDsCh | |||
| 1.3.6.1.2.1.10.146.1.3.1 | TabledvbInaIfDsChTable | not-accessible | current | |
| 1.3.6.1.2.1.10.146.1.3.1.1 | RowdvbInaIfDsChEntry | not-accessible | current | List of attributes for a single Downstream channel. An entry in this table exists for each downstream ifEntry. |
| 1.3.6.1.2.1.10.146.1.3.1.1.1 | ColumndvbInaIfDsChFrequency | read-write | current | The centre of the downstream frequency associated with this channel. |
| 1.3.6.1.2.1.10.146.1.3.1.1.2 | ColumndvbInaIfDsChConnections | read-only | current | Specifies the number of connections currently active for this down stream channel. |
| 1.3.6.1.2.1.10.146.1.3.1.1.3 | ColumndvbInaIfDsChTxPower | read-write | current | Specifies the down stream transmission power in dBuV of this interface. |
| 1.3.6.1.2.1.10.146.1.3.1.1.4 | ColumndvbInaIfDsChDownCoaxId | read-write | current | Specifies the coax ID of the Downstream HFC segment to which the downstream channel is connected. By default this parameter is zero. |
| 1.3.6.1.2.1.10.146.1.3.1.1.5 | ColumndvbInaIfDsChSymbolRate | read-write | current | Specifies the symbol rate for the Downstream channel. |
| 1.3.6.1.2.1.10.146.1.3.1.1.6 | ColumndvbInaIfDsChModulation | read-write | current | Specifies the modulation for the Downstream channel. |
| 1.3.6.1.2.1.10.146.1.3.1.1.7 | ColumndvbInaIfDsChType | read-write | current | Specifies if the Downstream channel is inband or out-of-band. |
| 1.3.6.1.2.1.10.146.1.3.1.1.8 | ColumndvbInaIfDsChDefaultPID | read-write | current | The default value of the MPEG PID of the elementary stream that carries the data on this downstream. See also dvbInaIfConPID. |
| 1.3.6.1.2.1.10.146.1.3.1.1.9 | ColumndvbInaIfDsChProvFrequency | read-write | current | Specifies the Downstream frequency of the provisioning channel. This setting is always used, no matter the provisioning channel is on this INA or on another. I… |
| 1.3.6.1.2.1.10.146.1.3.1.1.10 | ColumndvbInaIfDsChProvDownstreamType | read-write | current | Specifies the type of the downstream provisioning channel in the Provisioning Channel Message. 0 = QAM_MPEG, 1 = QPSK_1,544, 2 = QPSK_3,088 3..255 Reserved Thi… |
| 1.3.6.1.2.1.10.146.1.3.1.1.11 | ColumndvbInaIfDsChProvEnable | read-write | current | Specifies if this downstream channel is a Provisioning channel and as such transmits the Default Configuration Message. true = Provisioning channel false = not… |
| 1.3.6.1.2.1.10.146.1.3.1.1.12 | ColumndvbInaIfDsChProvTableIndex | read-write | current | If this downstream channel is a provisioning channel, then an index to the Provisioning tabel must be give here. |
| 1.3.6.1.2.1.10.146.1.4 | NodedvbInaIfUsCh | |||
| 1.3.6.1.2.1.10.146.1.4.1 | TabledvbInaIfUsChTable | not-accessible | current | Describes the attributes of attached upstream channels (frequency bands). |
| 1.3.6.1.2.1.10.146.1.4.1.1 | RowdvbInaIfUsChEntry | not-accessible | current | List of attributes for a single upstream channel. The state of the upstream channel depends on the state of the MAC and downstream channel. If one of both or b… |
| 1.3.6.1.2.1.10.146.1.4.1.1.1 | ColumndvbInaIfUsChFrequency | read-write | current | Specifies the frequency in Hz of the carrier used for this upstream channel. |
| 1.3.6.1.2.1.10.146.1.4.1.1.2 | ColumndvbInaIfUsChSymbolRate | read-write | current | Specifies the symbol rate for this upstream channel. |
| 1.3.6.1.2.1.10.146.1.4.1.1.3 | ColumndvbInaIfUsChModulation | read-write | current | Specifies the modulation for this upstream channel. |
| 1.3.6.1.2.1.10.146.1.4.1.1.4 | ColumndvbInaIfUsChMacFlagSet | read-only | current | Specifies the MAC flag set assigned to this upstream channel. |
| 1.3.6.1.2.1.10.146.1.4.1.1.5 | ColumndvbInaIfUsChId | read-only | current | Specifies the logical channel number associated with this upstream channel. |
| 1.3.6.1.2.1.10.146.1.4.1.1.6 | ColumndvbInaIfUsChConnections | read-only | current | Specifies the number of connections currently active for this upstream channel. |
| 1.3.6.1.2.1.10.146.1.4.1.1.9 | ColumndvbInaIfUsChCalibrationRxPower | read-write | current | Specifies the target receive signal power in dBuV to which the NIUs on this upstream channel are calibrated |
| 1.3.6.1.2.1.10.146.1.4.1.1.10 | ColumndvbInaIfUsChUpCoaxId | read-write | current | Specifies the coax ID of the UpStream HFC segment to which the upstream channel is connected. By default this parameter is zero. |
| 1.3.6.1.2.1.10.146.1.4.1.1.11 | ColumndvbInaIfUsChDownCoaxId | read-write | current | Specifies the coax ID of the Downstream HFC segment to which the upstream channel is connected. By default this parameter is zero. |
| 1.3.6.1.2.1.10.146.1.4.1.1.12 | ColumndvbInaIfUsChAtmCells | read-only | current | |
| 1.3.6.1.2.1.10.146.1.4.1.1.13 | ColumndvbInaIfUsChAtmTimingErrors | read-only | current | Number of ATM Cells received with Timing Error. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.4.1.1.14 | ColumndvbInaIfUsChAtmPowerErrors | read-only | current | Number of ATM Cells received with Signal Level Error. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.4.1.1.15 | ColumndvbInaIfUsChAtmRSCorrectableErrors | read-only | current | Number of ATM Cells received with correctable Reed-Solomon Errors. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.4.1.1.16 | ColumndvbInaIfUsChAtmRSNonCorrectableErrors | read-only | current | Number of ATM Cells received with non-correctable Reed-Solomon Errors. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.4.1.1.17 | ColumndvbInaIfUsChAtmHecErrors | read-only | current | Number of ATM Cells received with HEC Error. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.4.1.1.18 | ColumndvbInaIfUsChAal5CrcErrors | read-only | current | Number AAL5 frames received with CRC error. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.4.1.1.19 | ColumndvbInaIfUsChAtmCollisionErrors | read-only | current | Number of ATM Cells received with Collision detected. 0 can indicate the counter is not supported. |
| 1.3.6.1.2.1.10.146.1.5 | NodedvbInaIfNiu | |||
| 1.3.6.1.2.1.10.146.1.5.1 | TabledvbInaIfNiuTable | not-accessible | current | Describes the attributes of Network Interface Units. |
| 1.3.6.1.2.1.10.146.1.5.1.1 | RowdvbInaIfNiuEntry | not-accessible | current | Initially the table shall be empty. A new entry for a NIU is automatically created when the NIU in question signs on. Furthermore, the manager through the dvbI… |
| 1.3.6.1.2.1.10.146.1.5.1.1.1 | ColumndvbInaIfNiuMacAddress | not-accessible | current | A 48-bit value representing the unique MAC address of the NIU. |
| 1.3.6.1.2.1.10.146.1.5.1.1.2 | ColumndvbInaIfNiuRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.5.1.1.3 | ColumndvbInaIfNiuState | read-only | current | Returned status information is the NIU status as assumed by the INA. The following states are possible: null(1) Any state other than below. ranging(2): The NIU… |
| 1.3.6.1.2.1.10.146.1.5.1.1.4 | ColumndvbInaIfNiuDesiredState | read-create | current | Specifies the desired state of the NIU. This parameter can be set to one of the following values: down : Initial state. Disable NIU operation. start : Enable N… |
| 1.3.6.1.2.1.10.146.1.5.1.1.5 | ColumndvbInaIfNiuDownIfIndex | read-only | current | Specifies the IfIndex of the downstream channel on which the NIU is tuned. |
| 1.3.6.1.2.1.10.146.1.5.1.1.6 | ColumndvbInaIfNiuUpIfIndex | read-only | current | Specifies the IfIndex of the upstream channel that is used by the NIU. |
| 1.3.6.1.2.1.10.146.1.5.1.1.7 | ColumndvbInaIfNiuUpTxLevel | read-only | current | Specifies the upstream transmit level. This is the INA notion of NIU transmit level. (See also 'dvbInaIfNiuRespTxLevel'.) |
| 1.3.6.1.2.1.10.146.1.5.1.1.8 | ColumndvbInaIfNiuTimeOffset | read-only | current | Specifies the time offset. This is the INA notion of NIU time offset. (See also 'dvbInaIfNiuRespTimeOffset'.) |
| 1.3.6.1.2.1.10.146.1.5.1.1.9 | ColumndvbInaIfNiuStatus | read-only | current | This 32-bit object specifies the status of this NIU. See <MAC> Sign-On Response Message and <MAC> Status Response Message [1] for the exact bit assignment. Thi… |
| 1.3.6.1.2.1.10.146.1.5.1.1.10 | ColumndvbInaIfNiuErrorCode | read-only | current | This 16-bit object specifies the error code in the <MAC> Sign-On Response Message. See ES 200 800 for the exact bit assignment. |
| 1.3.6.1.2.1.10.146.1.5.1.1.11 | ColumndvbInaIfNiuRetryCount | read-only | current | This 8-bit object specifies the number of transmissions of the <MAC> Sign-On Response Message. (See [1]). |
| 1.3.6.1.2.1.10.146.1.5.1.1.12 | ColumndvbInaIfNiuCapabilities | read-only | current | This 32-bit object specifies the capabilities of this NIU. See also ES 200 800 for the bit assignment. |
| 1.3.6.1.2.1.10.146.1.5.1.1.13 | ColumndvbInaIfNiuExtendedCapabilities | read-only | current | This 32-bit object specifies the extended capabilities of this NIU. See also ES 200 800 and ECR 5 for the bit assignment. |
| 1.3.6.1.2.1.10.146.1.5.1.1.14 | ColumndvbInaIfNiuInitCompletionStatus | read-only | current | This 8-bit object indicates the errors in the initialisation phase of this NIU. See the <MAC> Initialization Complete Message ES 200 800 for the exact bit assi… |
| 1.3.6.1.2.1.10.146.1.5.1.1.15 | ColumndvbInaIfNiuRequestStatus | read-create | current | This object triggers the transmission of a <MAC> Status Request Message [1]. This parameter can be set to one of the following parameters: 'NiuReqAddressPars(0… |
| 1.3.6.1.2.1.10.146.1.5.1.1.16 | ColumndvbInaIfNiuResponseNumber | read-only | current | This object is incremented when a <MAC> Status Response Message [1] is received. This object can be polled to detect the reception of this message. After reset… |
| 1.3.6.1.2.1.10.146.1.5.1.1.17 | ColumndvbInaIfNiuRespTxLevel | read-only | current | Specifies the transmit power level of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'Niu… |
| 1.3.6.1.2.1.10.146.1.5.1.1.18 | ColumndvbInaIfNiuRespTimeOffset | read-only | current | Specifies the time offset of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLay… |
| 1.3.6.1.2.1.10.146.1.5.1.1.19 | ColumndvbInaIfNiuRespOoBDownFrequency | read-only | current | Specifies the OoB downstream frequency of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the … |
| 1.3.6.1.2.1.10.146.1.5.1.1.20 | ColumndvbInaIfNiuRespIBDownFrequency | read-only | current | Specifies the IB downstream frequency of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the '… |
| 1.3.6.1.2.1.10.146.1.5.1.1.21 | ColumndvbInaIfNiuRespSNRLevel | read-only | current | Specifies the estimated SNR level at the RF input of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a respo… |
| 1.3.6.1.2.1.10.146.1.5.1.1.22 | ColumndvbInaIfNiuRespRxLevel | read-only | current | Specifies the estimated downstream power level of the MAC messages at the RF input of the NIU. This object is updated after the reception of a <MAC> Status Res… |
| 1.3.6.1.2.1.10.146.1.5.1.1.23 | ColumndvbInaIfNiuDefaultConnectionId | read-create | current | Specifies the ConnectionId of the default connection that is assigned to this NIU. |
| 1.3.6.1.2.1.10.146.1.5.1.1.24 | ColumndvbInaIfNiuLifetime | read-create | current | Defines how long after the NIU was signed off, the entry is removed from the table. An infinite(0) value would mean that the values are stored at least until t… |
| 1.3.6.1.2.1.10.146.1.5.1.1.25 | ColumndvbInaIfNiuGrantProtocolTimeOut | read-create | current | The time that the NIU should wait before verifying the status of pending grants. Default value is dvbInaIfMacGrantProtocolTimeOut. |
| 1.3.6.1.2.1.10.146.1.5.1.1.26 | ColumndvbInaIfNiuSlotConfigurationErr | read-only | current | NIU Error Parameter: Slot_Configuration_CRC_Error_Count, the number of errors in Slot_Configuration_Count R bytes, as found by the CRC decoder. |
| 1.3.6.1.2.1.10.146.1.5.1.1.27 | ColumndvbInaIfNiuAtmPacketLoss | read-only | current | NIU Error Parameter: ATM_Packet_Loss_Count, the number of received ATM cells that were lost, either due to unrecoverable Reed-Solomon errors or because of an e… |
| 1.3.6.1.2.1.10.146.1.5.1.1.28 | ColumndvbInaIfNiuSlEsCrcErr | read-only | current | Niu Error Parameter: SL-ESF_CRC_Error_Count, the number of CRC errors found in consecutive C1-C6. |
| 1.3.6.1.2.1.10.146.1.5.1.1.29 | ColumndvbInaIfNiuSlEsFrameCount | read-only | current | NIU Error Parameter: SL-ESF_Frame_Count, the number of frames the statistics apply to. |
| 1.3.6.1.2.1.10.146.1.5.1.1.30 | ColumndvbInaIfNiuSlotConfigurationCount | read-only | current | NIU Error Parameter: Slot_Configuration_Count, the number of R-byte sets (Rxa-Rxc) used to calculate Pedersen Informational - Expires August 2001 45 DVB Cable … |
| 1.3.6.1.2.1.10.146.1.5.1.1.31 | ColumndvbInaIfNiuRSErrCorrectable | read-only | current | NIU Error Parameter: Reed_Solomon_Errors_Correctable, MPEG frames received with correctable Reed-Solomon Errors (IB only). |
| 1.3.6.1.2.1.10.146.1.5.1.1.32 | ColumndvbInaIfNiuRSErrNonCorrectable | read-only | current | NIU Error Parameter: Reed_Solomon_Errors_Non_Correctable, MPEG frames received with non-correctable Reed-Solomon Errors (IB only). |
| 1.3.6.1.2.1.10.146.1.5.1.1.33 | ColumndvbInaIfNiuSignOnTime | read-only | current | The value of sysUpTime at the time this NIU was signed on. If the time is unknown, this value shall be zero. |
| 1.3.6.1.2.1.10.146.1.5.1.1.34 | ColumndvbInaIfNiuDsChBytes | read-only | current | Number of bytes sent in direction INA to NIU. |
| 1.3.6.1.2.1.10.146.1.5.1.1.35 | ColumndvbInaIfNiuUsChBytes | read-only | current | Number of bytes sent in direction NIU to INA. Includes backbone, NIU-to-NIU and broadcast/multicast traffic. |
| 1.3.6.1.2.1.10.146.1.5.1.1.36 | ColumndvbInaIfNiuTimeRanging | read-only | current | Number of times the NIU has been time ranged. |
| 1.3.6.1.2.1.10.146.1.5.1.1.37 | ColumndvbInaIfNiuPowerRanging | read-only | current | Number of times the NIU has been power ranged. |
| 1.3.6.1.2.1.10.146.1.6 | NodedvbInaIfConnection | |||
| 1.3.6.1.2.1.10.146.1.6.1 | TabledvbInaIfConTable | not-accessible | current | Contains information about DVB-RC MAC connections. |
| 1.3.6.1.2.1.10.146.1.6.1.1 | RowdvbInaIfConEntry | not-accessible | current | Initially the table shall be empty. A new entry for a connection is automatically generated when a <MAC> Resource Request Message is received from the NIU in q… |
| 1.3.6.1.2.1.10.146.1.6.1.1.1 | ColumndvbInaIfConNiuMacAddress | not-accessible | current | MAC address of the NIU that is associated with the connection. |
| 1.3.6.1.2.1.10.146.1.6.1.1.2 | ColumndvbInaIfConConnectionId | not-accessible | current | Specifies the connection identifier to be used for this connection. |
| 1.3.6.1.2.1.10.146.1.6.1.1.3 | ColumndvbInaIfConCurrentState | read-only | current | Current state of the connection. The following states are possible: down(1) In this state an entry is made in the connection table for the connection in questi… |
| 1.3.6.1.2.1.10.146.1.6.1.1.4 | ColumndvbInaIfConDesiredState | read-create | current | Desired state for the connection. The following desired states are possible: down(1), up(3) and, downAlloc(5). |
| 1.3.6.1.2.1.10.146.1.6.1.1.5 | ColumndvbInaIfConConnectionType | read-create | current | Specifies the kind of connection: fixed rate, contention based, or reservation based. This parameter can be set to a value that is an OR of the following bits:… |
| 1.3.6.1.2.1.10.146.1.6.1.1.6 | ColumndvbInaIfConAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.6.1.1.7 | ColumndvbInaIfConEncapsulation | read-create | current | This object indicates the type of encapsulation provided on this connection. This object can have one of the following values: 'directIp(1)', 'ethernetMacBridg… |
| 1.3.6.1.2.1.10.146.1.6.1.1.8 | ColumndvbInaIfConAtmDownstreamVCC | read-only | current | ATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission. |
| 1.3.6.1.2.1.10.146.1.6.1.1.9 | ColumndvbInaIfConAtmUpstreamVCC | read-only | current | ATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission. |
| 1.3.6.1.2.1.10.146.1.6.1.1.10 | ColumndvbInaIfConFilterMACAddress | read-create | current | Specifies the 'soft' MPEG MPE MAC address used to filter the data out of the downstream IB transmission. This is found in the Downstream_Multiprotocol_CBD subs… |
| 1.3.6.1.2.1.10.146.1.6.1.1.11 | ColumndvbInaIfConPID | read-create | current | Specifies the MPEG PID of the elementary stream that carries the data. |
| 1.3.6.1.2.1.10.146.1.6.1.1.12 | ColumndvbInaIfConMaxContentionMsgLen | read-create | current | The Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. A… |
| 1.3.6.1.2.1.10.146.1.6.1.1.13 | ColumndvbInaIfConMaxReservationMsgLen | read-create | current | This is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by makin… |
| 1.3.6.1.2.1.10.146.1.6.1.1.14 | ColumndvbInaIfConAuxFlags | read-only | current | The Connection_Control_Field_Aux from the Connect Message Structure. This is used to indicate if the Priority, Downstream flowspec and Session binding objects … |
| 1.3.6.1.2.1.10.146.1.6.2 | TabledvbInaIfConQosTable | not-accessible | current | Contains information about connection quality for DVB-RC MAC connections. Both upstream and downstream quality parameters are found. |
| 1.3.6.1.2.1.10.146.1.6.2.1 | RowdvbInaIfConQosEntry | not-accessible | current | An entry in the table is automatically created when a new entry in the connection table connection is created Pedersen Informational - Expires August 2001 52 D… |
| 1.3.6.1.2.1.10.146.1.6.2.1.1 | ColumndvbInaIfConQosPriority | read-write | current | The priority of the connection. Connections with low priority field value can be reprovisioned in order to accommodate the requirements of connections with hig… |
| 1.3.6.1.2.1.10.146.1.6.2.1.2 | ColumndvbInaIfConQosDsReqMaxPacketSize | read-write | current | A downstream QoS parameter. Defines the requested maximum packet size in the downstream. The parameter can be set either by the managment system, or by the INA… |
| 1.3.6.1.2.1.10.146.1.6.2.1.3 | ColumndvbInaIfConQosDsReqBitrate | read-write | current | A downstream QoS parameter. Defines requested average bit rate in the downstream. The parameter can be set either by the managment system, or by the INA accord… |
| 1.3.6.1.2.1.10.146.1.6.2.1.4 | ColumndvbInaIfConQosDsReqJitter | read-write | current | A downstream QoS parameter. Defines the requested maximum allowed jitter in the downstream. The parameter can be set either by the managment system, or by the … |
| 1.3.6.1.2.1.10.146.1.6.2.1.5 | ColumndvbInaIfConQosDsAllocMaxPacketSize | read-only | current | A downstream QoS parameter. This is the actual maximum packet size supported by the INA in the downstream. The packet size includes propriety protocols header,… |
| 1.3.6.1.2.1.10.146.1.6.2.1.6 | ColumndvbInaIfConQosDsAllocBitrate | read-only | current | A downstream QoS parameter. This is the actual average bit rate supported by the INA in the downstream. |
| 1.3.6.1.2.1.10.146.1.6.2.1.7 | ColumndvbInaIfConQosDsAllocJitter | read-only | current | A downstream QoS parameter. This is the actual maximum jitter supported by the INA in the downstream. |
| 1.3.6.1.2.1.10.146.1.6.2.1.8 | ColumndvbInaIfConQosUsReqBw | read-write | current | An upstream QoS parameter. The requested bandwidth for the upstream. The parameter can be set either by the managment system, or by the INA according to the NI… |
| 1.3.6.1.2.1.10.146.1.6.2.1.9 | ColumndvbInaIfConQosUsReqMaxDistSlots | read-write | current | An upstream QoS parameter. The requested maximum distance between slots for the upstream. The parameter can be set either by the managment system, or by the IN… |
| 1.3.6.1.2.1.10.146.1.6.2.1.10 | ColumndvbInaIfConQosUsReqFrameLength | read-write | current | |
| 1.3.6.1.2.1.10.146.1.6.2.1.11 | ColumndvbInaIfConQosUsAllocBw | read-only | current | An upstream QoS parameter. The actual allocated bandwidth for the upstream. |
| 1.3.6.1.2.1.10.146.1.6.2.1.12 | ColumndvbInaIfConQosUsAllocMaxDistSlots | read-only | current | An upstream QoS parameter. The allocated distance between slots for the upstream. In case of using a cyclic assignment, this is the parameter sent by the INA i… |
| 1.3.6.1.2.1.10.146.1.6.2.1.13 | ColumndvbInaIfConQosUsAllocFrameLength | read-only | current | An upstream QoS parameter. The allocated frame length for the upstream. In case of using a cyclic assignment, this is the parameter sent by the INA in the conn… |
| 1.3.6.1.2.1.10.146.1.6.2.1.14 | ColumndvbInaIfConQosUsReqFixedRateMethod | read-write | current | An upstream QoS parameter. Request a specific fixed rate slot assignment method to be used. If cyclic then cyclic assignment is used. If slotList then the slot… |
| 1.3.6.1.2.1.10.146.1.6.2.1.15 | ColumndvbInaIfConQosUsAllocFixedRateMethod | read-only | current | An upstream QoS parameter. Reflects the actual fixed rate slot assignment method that is used. If cyclic then cyclic assignment is used. If slotList then the s… |
| 1.3.6.1.2.1.10.146.1.6.3 | TabledvbInaIfConSesTable | not-accessible | current | |
| 1.3.6.1.2.1.10.146.1.6.3.1 | RowdvbInaIfConSesEntry | not-accessible | current | An entry in the table is automatically created when a new entry in the connection table connection is created if the INA and the NIU supports session binding. … |
| 1.3.6.1.2.1.10.146.1.6.3.1.1 | ColumndvbInaIfConSesUsControl | read-only | current | Control which fields of the upstream session binding parameters that are used. |
| 1.3.6.1.2.1.10.146.1.6.3.1.2 | ColumndvbInaIfConSesUsNiuClientSrcIpType | read-only | current | The type of the IP source address of the NIU client. |
| 1.3.6.1.2.1.10.146.1.6.3.1.3 | ColumndvbInaIfConSesUsNiuClientSrcIp | read-only | current | The IP source address of the NIU client. Only used if bit 0 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.4 | ColumndvbInaIfConSesUsNiuClientDstIpType | read-only | current | The type of the IP destination address of the NIU client. |
| 1.3.6.1.2.1.10.146.1.6.3.1.5 | ColumndvbInaIfConSesUsNiuClientDstIp | read-only | current | The IP destination address of the NIU client. Only used if bit 1 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.6 | ColumndvbInaIfConSesUsNiuClientSrcPort | read-only | current | The source port of the NIU client. Only used if bit 2 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.7 | ColumndvbInaIfConSesUsNiuClientDstPort | read-only | current | The destination port of the NIU client. Only used if bit 3 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.8 | ColumndvbInaIfConSesUsTransportProtocol | read-only | current | The transport protocol used by the NIU client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfConSesUsControl is se… |
| 1.3.6.1.2.1.10.146.1.6.3.1.9 | ColumndvbInaIfConSesUsNiuClientSrcMac | read-only | current | The Ethernet source MAC address of the NIU client. Only used if bit 5 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.10 | ColumndvbInaIfConSesUsNiuClientDstMac | read-only | current | The Ethernet destination MAC address of the NIU client. Only used if bit 6 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.11 | ColumndvbInaIfConSesUsEthernetProtocol | read-only | current | The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfConSesUsContr… |
| 1.3.6.1.2.1.10.146.1.6.3.1.12 | ColumndvbInaIfConSesUsSessionId | read-only | current | The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.13 | ColumndvbInaIfConSesDsControl | read-only | current | Control which fields of the downstream session binding parameters that are used. |
| 1.3.6.1.2.1.10.146.1.6.3.1.14 | ColumndvbInaIfConSesDsInaClientSrcIpType | read-only | current | The type of the IP source address of the INA client. |
| 1.3.6.1.2.1.10.146.1.6.3.1.15 | ColumndvbInaIfConSesDsInaClientSrcIp | read-only | current | The IP source address of the INA client. Only used if bit 0 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.16 | ColumndvbInaIfConSesDsInaClientDstIpType | read-only | current | The type of the IP destination address of the INA client. |
| 1.3.6.1.2.1.10.146.1.6.3.1.17 | ColumndvbInaIfConSesDsInaClientDstIp | read-only | current | The IP destination address of the INA client. Only used if bit 1 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.18 | ColumndvbInaIfConSesDsInaClientSrcPort | read-only | current | The source port of the INA client. Only used if bit 2 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.19 | ColumndvbInaIfConSesDsInaClientDstPort | read-only | current | The destination port of the INA client. Only used if bit 3 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.20 | ColumndvbInaIfConSesDsTransportProtocol | read-only | current | The transport protocol used by the INA client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfConSesDsControl is se… |
| 1.3.6.1.2.1.10.146.1.6.3.1.21 | ColumndvbInaIfConSesDsInaClientSrcMac | read-only | current | The Ethernet source MAC address of the INA client. Only used if bit 5 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.22 | ColumndvbInaIfConSesDsInaClientDstMac | read-only | current | The Ethernet destination MAC address of the INA client. Only used if bit 6 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.3.1.23 | ColumndvbInaIfConSesDsEthernetProtocol | read-only | current | The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfConSesDsContr… |
| 1.3.6.1.2.1.10.146.1.6.3.1.24 | ColumndvbInaIfConSesDsSessionId | read-only | current | The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.6.4 | TabledvbInaIfConHdrSupTable | not-accessible | current | Table contains information about the header suppression for a connection, indexed trough the Connection ID and the Context ID. |
| 1.3.6.1.2.1.10.146.1.6.4.1 | RowdvbInaIfConHdrSupEntry | not-accessible | current | An entry in the table is automatically generated when a new header suppression starts. Or when a reprovisioning is made. An entry is deleted when the connectio… |
| 1.3.6.1.2.1.10.146.1.6.4.1.1 | ColumndvbInaIfConHdrSupContextId | not-accessible | current | The context ID for the header suppression session. |
| 1.3.6.1.2.1.10.146.1.6.4.1.2 | ColumndvbInaIfConHdrSupDirection | not-accessible | current | The direction for this the header suppression session. |
| 1.3.6.1.2.1.10.146.1.6.4.1.3 | ColumndvbInaIfConHdrSupControl | read-only | current | String of bits that control the use of the header suppression. Each of the first 103 bits, indicates if a byte in the header is suppressed or not. Bit 103 is u… |
| 1.3.6.1.2.1.10.146.1.6.4.1.4 | ColumndvbInaIfConHdrSupGeneration | read-only | current | The generation number that is attached to the header fields value. |
| 1.3.6.1.2.1.10.146.1.6.4.1.5 | ColumndvbInaIfConHdrSupHeaderLength | read-only | current | The number of usefull bytes in the suppression header. This is the number of the last zero in the dvbInaIfConHdrSupControl. |
| 1.3.6.1.2.1.10.146.1.6.4.1.6 | ColumndvbInaIfConHdrSupHeader | read-only | current | The header used for header suppression. Both fixed and changing fields together. Only the first dvbInaIfConHdrSupHeaderLength is used. |
| 1.3.6.1.2.1.10.146.1.7 | NodedvbInaIfReprov | |||
| 1.3.6.1.2.1.10.146.1.7.1 | TabledvbInaIfReprovSrcNiuTable | not-accessible | current | The table describes information created on INA 1 for a NIU that is about to be reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.1.1 | RowdvbInaIfReprovSrcNiuEntry | not-accessible | current | An entry in the table is created by the manager when a NIU is about to be reprovisioned. When the reprovisioning is done and the NIU entry is deleted after dvb… |
| 1.3.6.1.2.1.10.146.1.7.1.1.1 | ColumndvbInaIfReprovSrcNiuRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.7.1.1.2 | ColumndvbInaIfReprovSrcNiuCommand | read-create | current | Controls the reprovisioning on INA 1. When set to reprovStart the actual reporvisioning on INA 1 is initiated with a Reprovisioning Message to the NIU. Everyth… |
| 1.3.6.1.2.1.10.146.1.7.1.1.3 | ColumndvbInaIfReprovSrcNiuDsChFrequency | read-create | current | The centre of the new downstream frequency when the NIU is reprovisioned to INA 2. |
| 1.3.6.1.2.1.10.146.1.7.1.1.4 | ColumndvbInaIfReprovSrcNiuDsChSymbolRate | read-create | current | Specifies the new symbol rate for the Downstream channel when the NIU is reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.1.1.5 | ColumndvbInaIfReprovSrcNiuDsChModulation | read-create | current | Specifies the new modulation for the Downstream channel when the NIU is reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.1.1.6 | ColumndvbInaIfReprovSrcNiuDsChType | read-create | current | Specifies if the new Downstream channel is inband or out-of-band when the NIU is reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.1.1.7 | ColumndvbInaIfReprovSrcNiuUsChFrequency | read-create | current | Specifies the new upstream channel frequency in Hz when the NIU is reprovisoned. |
| 1.3.6.1.2.1.10.146.1.7.1.1.8 | ColumndvbInaIfReprovSrcNiuUsChSymbolRate | read-create | current | Specifies the new upstream channel symbol rate when the NIU is reprovisoned. |
| 1.3.6.1.2.1.10.146.1.7.1.1.9 | ColumndvbInaIfReprovSrcNiuUsChModulation | read-create | current | Specifies the new upstream modulation when the NIU is reprovisoned. |
| 1.3.6.1.2.1.10.146.1.7.1.1.10 | ColumndvbInaIfReprovSrcNiuUsChId | read-only | current | Specifies the new logical channel number associated with the upstream channel when the NIU is reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.2 | TabledvbInaIfReprovDstNiuTable | not-accessible | current | The table describes information created on INA 2 for a NIU that is about to be reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.2.1 | RowdvbInaIfReprovDstNiuEntry | not-accessible | current | An entry in the table is created by the manager when a NIU is about to be reprovisioned. When the reprovisioning is done and the NIU signs on to INA 2 the info… |
| 1.3.6.1.2.1.10.146.1.7.2.1.1 | ColumndvbInaIfReprovDstNiuMacAddress | not-accessible | current | A 48-bit value representing the unique MAC address of the NIU to be reprovisioned. This is the index of the table. |
| 1.3.6.1.2.1.10.146.1.7.2.1.2 | ColumndvbInaIfReprovDstNiuRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.7.2.1.3 | ColumndvbInaIfReprovDstNiuCommand | read-create | current | Controls the reprovisioning on INA 2. When set to reprovPrepare INA 2 will generate the necessary information that needs to be transferred back to INA 1. This … |
| 1.3.6.1.2.1.10.146.1.7.2.1.4 | ColumndvbInaIfReprovDstNiuDownIfIndex | read-create | current | Specifies the IfIndex of the downstream channel on which the NIU is tuned after the reprovisioning. |
| 1.3.6.1.2.1.10.146.1.7.2.1.5 | ColumndvbInaIfReprovDstNiuUpIfIndex | read-create | current | Specifies the IfIndex of the upstream channel that is used by the NIU after the reprovisioning. |
| 1.3.6.1.2.1.10.146.1.7.2.1.6 | ColumndvbInaIfReprovDstNiuLifetime | read-create | current | Defines how long time after the NIU signs off, the NIU entry is removed from the NIU table. An infinite(0) value would mean that the values are stored at least… |
| 1.3.6.1.2.1.10.146.1.7.3 | TabledvbInaIfReprovSrcConTable | not-accessible | current | Contains information about DVB-RC MAC connections on INA 1 that is about to be reprovisioned. |
| 1.3.6.1.2.1.10.146.1.7.3.1 | RowdvbInaIfReprovSrcConEntry | not-accessible | current | The entries in the table are created by the manager when a NIU on INA 1 is about to be reprovisioned. After the NIU is reprovisoned the entries are automatical… |
| 1.3.6.1.2.1.10.146.1.7.3.1.1 | ColumndvbInaIfReprovSrcConRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.7.3.1.2 | ColumndvbInaIfReprovSrcConConnectionIdNew | read-create | current | Specifies the new value for the connection identifier to be used for this connection after the reprovisioning. The management system must get this value from I… |
| 1.3.6.1.2.1.10.146.1.7.3.1.3 | ColumndvbInaIfReprovSrcConPID | read-create | current | Specifies the new MPEG PID of the elementary stream that carries the data after the reprovisioning. |
| 1.3.6.1.2.1.10.146.1.7.3.1.4 | ColumndvbInaIfReprovSrcConDsVc | read-create | current | ATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission after reprovisioning. The management system must get this va… |
| 1.3.6.1.2.1.10.146.1.7.3.1.5 | ColumndvbInaIfReprovSrcConUsVc | read-create | current | ATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission after reprovisioning. The management system must get this value fr… |
| 1.3.6.1.2.1.10.146.1.7.4 | TabledvbInaIfReprovDstConTable | not-accessible | current | Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. |
| 1.3.6.1.2.1.10.146.1.7.4.1 | RowdvbInaIfReprovDstConEntry | not-accessible | current | The entries in the table are created by the manager when a NIU is about to be reprovisioned to INA 2. After the NIU has signed on to INA 2, the information in … |
| 1.3.6.1.2.1.10.146.1.7.4.1.1 | ColumndvbInaIfReprovDstConConnectionIdOld | not-accessible | current | Specifies the old value for the connection identifier that is used on INA 1. The management system must get this value from INA 1. |
| 1.3.6.1.2.1.10.146.1.7.4.1.2 | ColumndvbInaIfReprovDstConRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.7.4.1.3 | ColumndvbInaIfReprovDstConConnectionIdNew | read-only | current | Specifies the new value for the connection identifier that is used on INA 2. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare. |
| 1.3.6.1.2.1.10.146.1.7.4.1.4 | ColumndvbInaIfReprovDstConConnectionType | read-create | current | Specifies the kind of connection: fixed rate, contention Pedersen Informational - Expires August 2001 74 DVB Cable INA Interface MIB Feb 2001 based, or reserva… |
| 1.3.6.1.2.1.10.146.1.7.4.1.5 | ColumndvbInaIfReprovDstConEncapsulation | read-create | current | This object indicates the type of encapsulation provided on this connection. This object can have one of the following values: 'directIp(1)', 'ethernetMacBridg… |
| 1.3.6.1.2.1.10.146.1.7.4.1.6 | ColumndvbInaIfReprovDstConAtmDownstreamVCC | read-only | current | ATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission. INA 2 creates this value when dvbInaIfReprovDstNiuCommand i… |
| 1.3.6.1.2.1.10.146.1.7.4.1.7 | ColumndvbInaIfReprovDstConAtmUpstreamVCC | read-only | current | ATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set … |
| 1.3.6.1.2.1.10.146.1.7.4.1.8 | ColumndvbInaIfReprovDstConFilterMACAddress | read-create | current | |
| 1.3.6.1.2.1.10.146.1.7.4.1.9 | ColumndvbInaIfReprovDstConPID | read-only | current | Specifies the MPEG PID of the elementary stream that carries the data. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare. |
| 1.3.6.1.2.1.10.146.1.7.4.1.10 | ColumndvbInaIfReprovDstConMaxContentionMsgLen | read-create | current | The Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. A… |
| 1.3.6.1.2.1.10.146.1.7.4.1.11 | ColumndvbInaIfReprovDstConMaxReservationMsgLen | read-create | current | This is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by makin… |
| 1.3.6.1.2.1.10.146.1.7.4.1.12 | ColumndvbInaIfReprovDstConAuxFlags | read-only | current | The Connection_Control_Field_Aux from the Connect Message Structure. This is used to indicate if the Priority, Downstream flowspec and Session binding objects … |
| 1.3.6.1.2.1.10.146.1.7.5 | TabledvbInaIfReprovDstConSesTable | not-accessible | current | Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. |
| 1.3.6.1.2.1.10.146.1.7.5.1 | RowdvbInaIfReprovDstConSesEntry | not-accessible | current | The entries in the table are created automatically when an entry in the dvbInaIfReprovDstConTable is created and the INA support session binding. You must alwa… |
| 1.3.6.1.2.1.10.146.1.7.5.1.1 | ColumndvbInaIfReprovDstConSesUsControl | read-write | current | Control which fields of the upstream session binding parameters that are used. |
| 1.3.6.1.2.1.10.146.1.7.5.1.2 | ColumndvbInaIfReprovDstConSesUsNiuClientSrcIpType | read-write | current | The type of the IP source address of the NIU client. |
| 1.3.6.1.2.1.10.146.1.7.5.1.3 | ColumndvbInaIfReprovDstConSesUsNiuClientSrcIp | read-write | current | The IP source address of the NIU client. Only used if bit 0 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.4 | ColumndvbInaIfReprovDstConSesUsNiuClientDstIpType | read-write | current | The type of the IP destination address of the NIU client. |
| 1.3.6.1.2.1.10.146.1.7.5.1.5 | ColumndvbInaIfReprovDstConSesUsNiuClientDstIp | read-write | current | The IP destination address of the NIU client. Only used if bit 1 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.6 | ColumndvbInaIfReprovDstConSesUsNiuClientSrcPort | read-write | current | The source port of the NIU client. Only used if bit 2 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.7 | ColumndvbInaIfReprovDstConSesUsNiuClientDstPort | read-write | current | The destination port of the NIU client. Only used if bit 3 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.8 | ColumndvbInaIfReprovDstConSesUsTransportProtocol | read-write | current | The transport protocol used by the NIU client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfReprovDstConSesUsCont… |
| 1.3.6.1.2.1.10.146.1.7.5.1.9 | ColumndvbInaIfReprovDstConSesUsNiuClientSrcMac | read-write | current | The Ethernet source MAC address of the NIU client. Only used if bit 5 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.10 | ColumndvbInaIfReprovDstConSesUsNiuClientDstMac | read-write | current | The Ethernet destination MAC address of the NIU client. Only used if bit 6 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.11 | ColumndvbInaIfReprovDstConSesUsEthernetProtocol | read-write | current | The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfReprovDstConS… |
| 1.3.6.1.2.1.10.146.1.7.5.1.12 | ColumndvbInaIfReprovDstConSesUsSessionId | read-write | current | The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfReprovDstConSesUsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.13 | ColumndvbInaIfReprovDstConSesDsControl | read-write | current | Control which fields of the downstream session binding parameters that are used. |
| 1.3.6.1.2.1.10.146.1.7.5.1.14 | ColumndvbInaIfReprovDstConSesDsInaClientSrcIpType | read-write | current | The type of the IP source address of the INA client. |
| 1.3.6.1.2.1.10.146.1.7.5.1.15 | ColumndvbInaIfReprovDstConSesDsInaClientSrcIp | read-write | current | The IP source address of the INA client. Only used if bit 0 of dvbInaIfReprovDstConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.16 | ColumndvbInaIfReprovDstConSesDsInaClientDstIpType | read-write | current | The type of the IP destination address of the INA client. |
| 1.3.6.1.2.1.10.146.1.7.5.1.17 | ColumndvbInaIfReprovDstConSesDsInaClientDstIp | read-write | current | The IP destination address of the INA client. Only used if bit 1 of dvbInaIfReprovDstConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.18 | ColumndvbInaIfReprovDstConSesDsInaClientSrcPort | read-write | current | The source port of the INA client. Only used if bit 2 of dvbInaIfReprovDstConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.19 | ColumndvbInaIfReprovDstConSesDsInaClientDstPort | read-write | current | The destination port of the INA client. Only used if bit 3 of dvbInaIfReprovDstConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.20 | ColumndvbInaIfReprovDstConSesDsTransportProtocol | read-write | current | The transport protocol used by the INA client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfReprovDstConSesDsCont… |
| 1.3.6.1.2.1.10.146.1.7.5.1.21 | ColumndvbInaIfReprovDstConSesDsInaClientSrcMac | read-write | current | The Ethernet source MAC address of the INA client. Only used if bit 5 of dvbInaIfReprovDstConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.5.1.22 | ColumndvbInaIfReprovDstConSesDsInaClientDstMac | read-write | current | The Ethernet destination MAC address of the INA client. Only used if bit 6 of dvbInaIfReprovDstConSesDsControl Pedersen Informational - Expires August 2001 82 … |
| 1.3.6.1.2.1.10.146.1.7.5.1.23 | ColumndvbInaIfReprovDstConSesDsEthernetProtocol | read-write | current | The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfReprovDstConS… |
| 1.3.6.1.2.1.10.146.1.7.5.1.24 | ColumndvbInaIfReprovDstConSesDsSessionId | read-write | current | The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfReprovDstConSesDsControl is set. |
| 1.3.6.1.2.1.10.146.1.7.6 | TabledvbInaIfReprovDstConHdrSupTable | not-accessible | current | Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. |
| 1.3.6.1.2.1.10.146.1.7.6.1 | RowdvbInaIfReprovDstConHdrSupEntry | not-accessible | current | The entries in the table are created by the manager when a NIU is about to be reprovisioned to INA 2. After the NIU has signed on to INA 2, the information in … |
| 1.3.6.1.2.1.10.146.1.7.6.1.1 | ColumndvbInaIfReprovDstConHdrSupContextId | not-accessible | current | The context ID for the header suppression session. |
| 1.3.6.1.2.1.10.146.1.7.6.1.2 | ColumndvbInaIfReprovDstConHdrSupDirection | not-accessible | current | The direction for this the header suppression session. |
| 1.3.6.1.2.1.10.146.1.7.6.1.3 | ColumndvbInaIfReprovDstConHdrSupRowAccessStatus | read-create | current | Controls and reflects the status of this row in this table. |
| 1.3.6.1.2.1.10.146.1.7.6.1.4 | ColumndvbInaIfReprovDstConHdrSupControl | read-only | current | String of bits that control the use of the header suppression. Each of the fisrt 103 bits, indicates if a byte in the header is suppressed or not. Bit 103 is u… |
| 1.3.6.1.2.1.10.146.1.7.6.1.5 | ColumndvbInaIfReprovDstConHdrSupGeneration | read-only | current | The generation number that is attached to the header fields value. |
| 1.3.6.1.2.1.10.146.1.7.6.1.6 | ColumndvbInaIfReprovDstConHdrSupHeaderLength | read-only | current | The number of usefull bytes in the suppression header. This is the number of the last zero in the dvbInaIfReprovDstConHdrSupControl. |
| 1.3.6.1.2.1.10.146.1.7.6.1.7 | ColumndvbInaIfReprovDstConHdrSupHeader | read-only | current | The header used for header suppression. Both fixed and changing fields together. Only the first dvbInaIfReprovDstConHdrSupHeaderLength is used. |
| 1.3.6.1.2.1.10.146.1.7.7 | TabledvbInaIfReprovDstConQosTable | not-accessible | current | Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. |
| 1.3.6.1.2.1.10.146.1.7.7.1 | RowdvbInaIfReprovDstConQosEntry | not-accessible | current | The entries in the table are created automatically when an entry in the dvbInaIfReprovDstConTable is created and the INA support QoS settings. After the NIU ha… |
| 1.3.6.1.2.1.10.146.1.7.7.1.1 | ColumndvbInaIfReprovDstConQosPriority | read-create | current | The priority of the connection. Connections with low priority field value can be Pedersen Informational - Expires August 2001 86 DVB Cable INA Interface MIB Fe… |
| 1.3.6.1.2.1.10.146.1.7.7.1.2 | ColumndvbInaIfReprovDstConQosDsReqMaxPacketSize | read-create | current | A downstream QoS parameter. Defines the requested maximum packet size in the downstream. The parameter can be set either by the managment system, or by the INA… |
| 1.3.6.1.2.1.10.146.1.7.7.1.3 | ColumndvbInaIfReprovDstConQosDsReqBitrate | read-create | current | A downstream QoS parameter. Defines requested average bit rate in the downstream. |
| 1.3.6.1.2.1.10.146.1.7.7.1.4 | ColumndvbInaIfReprovDstConQosDsReqJitter | read-create | current | A downstream QoS parameter. Defines the requested maximum allowed jitter in the downstream. |
| 1.3.6.1.2.1.10.146.1.7.7.1.5 | ColumndvbInaIfReprovDstConQosUsReqBw | read-create | current | An upstream QoS parameter. The requested bandwidth for the upstream. |
| 1.3.6.1.2.1.10.146.1.7.7.1.6 | ColumndvbInaIfReprovDstConQosUsReqMaxDistSlots | read-create | current | An upstream QoS parameter. The requested maximum distance between slots for the upstream. |
| 1.3.6.1.2.1.10.146.1.7.7.1.7 | ColumndvbInaIfReprovDstConQosUsReqFrameLength | read-create | current | An upstream QoS parameter. The requested frame length for the upstream. |
| 1.3.6.1.2.1.10.146.1.7.7.1.8 | ColumndvbInaIfReprovDstConQosUsReqFixedRateMethod | read-create | current | An upstream QoS parameter. Request a specific fixed rate slot assignment method to be used. If cyclic then cyclic assignment is used. If slotList then the slot… |
| 1.3.6.1.2.1.10.146.2 | NodedvbInaIfMIBConform | |||
| 1.3.6.1.2.1.10.146.2.1 | NodedvbInaIfCompliances | |||
| 1.3.6.1.2.1.10.146.2.1.1 | CompliancedvbInaIfCompliance | read-only | current | The compliance statement for EuroModem INAs which implement the DVB-CABLE-INA-IF-MIB MIB. An implementation only has to support IPv4 addresses to be compliant. |
| 1.3.6.1.2.1.10.146.2.2 | NodedvbInaIfGroups | |||
| 1.3.6.1.2.1.10.146.2.2.1 | GroupdvbInaIfMacGroup | current | A collection of objects providing capabilities and statistics for the MAC layer. | |
| 1.3.6.1.2.1.10.146.2.2.2 | GroupdvbInaIfProvisionGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.3 | GroupdvbInaIfDsChGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.4 | GroupdvbInaIfUsChGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.5 | GroupdvbInaIfNiuGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.6 | GroupdvbInaIfConnectionGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.7 | GroupdvbInaIfConQosGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.8 | GroupdvbInaIfConSesGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.9 | GroupdvbInaIfConHdrSupGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.10 | GroupdvbInaIfReprovSrcNiuGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.11 | GroupdvbInaIfReprovDstNiuGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.12 | GroupdvbInaIfReprovSrcConGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.13 | GroupdvbInaIfReprovDstConGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.14 | GroupdvbInaIfReprovDstConSesGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.15 | GroupdvbInaIfReprovDstConHdrSupGroup | current | ||
| 1.3.6.1.2.1.10.146.2.2.16 | GroupdvbInaIfReprovDstConQosGroup | current |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DownFrequency | Integer32 ( 70000000..862000000 ) | current | Downstream frequency range |
| DownstreamSymbolrate | INTEGER ( 0..4294967295 ) | current | The downstream transmission symbol rate used in symbol/s The symbol rate is given as an integer. Commonly used symbolrates are : symbol/s 6800000 IB 8Mhz 6875000 IB 8Mhz Pedersen Informational - Expires August 2001 16 D… |
| EtsTimeOut | INTEGER { etsTODisabled(0), etsTO9ms(1), etsTO30ms(2), etsTO60ms(3), etsTO90ms(4), etsTO300ms(5), Pedersen Informational - Expires August 2001 15 DVB Cable INA Interface MIB Feb 2001 etsTO600ms(6), etsTO900ms(7), etsTO3000ms(8), etsTO6000ms(9), etsTO9000ms(10), etsTO30000ms(11), etsTO60000ms(12) } | current | This data type represents possible timeout values. See also ES 200 800, section 5.5.3.2. |
| MacFlagSet | INTEGER ( 1..16 ) | current | This data type represents a reference to a set of MAC Flags. This reference is used in different MAC messages. See also ES 200 800, section 5.3.1.3. |
| Modulation | INTEGER { qpsk(1), qam16(2), qam32(3), qam64(4), qam128(5), qam256(6) } | current | Modulation type: OOB: qpsk(1) IB : qpsk(1), qam16(2), qam32(3), qam64(4), qam128(5), qam256(6) |
| UpFrequency | Integer32 ( 5000000..65000000 ) | current | Upstream frequency range |
| UpstreamSymbolrate | INTEGER { sr0128000(1), sr0772000(2), sr1544000(3), sr3088000(4) } | current | The upstream transmission symbol rate used. symbol/s sr0128000 optional Grade A sr0772000 optional Grade B sr1544000 mandatory Grade C sr3088000 optional Grade D |