DVB-MGTR101290-MIB
965 objects
DVB Measurement Group MIB to support TR 101 290. This tr101290 module contains measurements defined in TR 101 290.
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 enterprises Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2696 | Nodedvb | |||
| 1.3.6.1.4.1.2696.3 | Nodemg | |||
| 1.3.6.1.4.1.2696.3.2 | Identitytr101290 | DVB Measurement Group MIB to support TR 101 290. This tr101290 module contains measurements defined in TR 101 290. | ||
| 1.3.6.1.4.1.2696.3.2.1 | Nodetr101290Objects | |||
| 1.3.6.1.4.1.2696.3.2.1.1 | Nodetr101290Control | |||
| 1.3.6.1.4.1.2696.3.2.1.1.1 | ScalarcontrolNow | read-write | current | The current date and time at the location of the measurement equipment. It is highly desirable that the offset from UTC should be included. It is possible to s… |
| 1.3.6.1.4.1.2696.3.2.1.1.2 | ScalarcontrolEventPersistence | read-write | current | The persistence timer used with Event errors. An Event error test remains in the 'fail' state for this length of time after the occurrence of the Event. |
| 1.3.6.1.4.1.2696.3.2.1.1.3 | TablecontrolRFSystemTable | not-accessible | current | Table which controls the RF modulation expected to be received on each input. |
| 1.3.6.1.4.1.2696.3.2.1.1.3.1 | RowcontrolRFSystemEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.1.3.1.1 | ColumnrfSystemInputNumber | not-accessible | current | RF input whose mode of operation is to be set |
| 1.3.6.1.4.1.2696.3.2.1.1.3.1.2 | ColumnrfSystemDelivery | read-write | current | The type of signal the instrument should expect at its input. |
| 1.3.6.1.4.1.2696.3.2.1.1.4 | TablecontrolSynchronizationTable | not-accessible | current | Table reserved for future specification of synchronized timing. |
| 1.3.6.1.4.1.2696.3.2.1.1.4.1 | RowcontrolSynchronizationEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.1.4.1.1 | ColumncontrolSynchronizationInputNumber | not-accessible | current | Transport Stream number to which the objects in this row apply. |
| 1.3.6.1.4.1.2696.3.2.1.1.4.1.2 | ColumncontrolSynchronizedTime | read-write | current | This object is reserved pending future standardisation of timestamping of Transport Streams. |
| 1.3.6.1.4.1.2696.3.2.1.2 | Nodetr101290Trap | |||
| 1.3.6.1.4.1.2696.3.2.1.2.0 | NodetrapPrefix | |||
| 1.3.6.1.4.1.2696.3.2.1.2.0.1 | NotificationtestFailTrap | current | This trap is sent when a test which is not associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' ob… | |
| 1.3.6.1.4.1.2696.3.2.1.2.0.2 | NotificationmeasurementFailTrap | current | Trap which is sent when a test which is associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' objec… | |
| 1.3.6.1.4.1.2696.3.2.1.2.0.3 | NotificationmeasurementUnknownTrap | current | Trap which is sent when a measurement value becomes unavailable. This trap is triggered by the transition of the '...MeasurementState' object associated with t… | |
| 1.3.6.1.4.1.2696.3.2.1.2.1 | TabletrapControlTable | not-accessible | current | Table of trap control information for each input |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1 | RowtrapControlEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.1 | ColumntrapControlInputNumber | not-accessible | current | Each Transport Stream input has separate trap control parameters. This object identifies the Transport Stream input to which the trap control parameters apply |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.2 | ColumntrapControlOID | accessible-for-notify | current | In the case of a testFailTrap or a measurementFailTrap, this object holds the OID of the '...State' or '...TestState' object whose transition to 'fail' has tri… |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.3 | ColumntrapControlGenerationTime | accessible-for-notify | current | In the case of a testFailTrap or a measurementFailTrap, at the moment when the trap is generated, the value of the '...LatestError' object associated with the … |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.4 | ColumntrapControlMeasurementValue | accessible-for-notify | current | At the moment when a measurementFailTrap is generated, the value of this object is set from the '...Value' object associated with the measurement which caused … |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.5 | ColumntrapControlRateStatus | read-write | current | This object is used for rate control of traps, preventing overload of the management network by transmission of an excessive number of traps. The value 'disabl… |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.6 | ColumntrapControlPeriod | read-write | current | An agent will ensure that the interval between sending traps is no shorter than this time period. The management system can override this by setting trapContro… |
| 1.3.6.1.4.1.2696.3.2.1.2.1.1.7 | ColumntrapControlFailureSummary | read-only | current | This bit string contains a summary of all the test failures. If the bit for the test is set to one, that test is in a fail state. When a trap is being generate… |
| 1.3.6.1.4.1.2696.3.2.1.2.2 | ScalartrapInput | accessible-for-notify | current | The Transport Stream input whose change triggered the current trap. This information can also be obtained by analysing the trapControlOID, but trapInput provid… |
| 1.3.6.1.4.1.2696.3.2.1.3 | Nodetr101290Capability | |||
| 1.3.6.1.4.1.2696.3.2.1.3.1 | ScalarcapabilityMIBRevision | read-only | current | The capabilities of the agent are expressed in relation to a specific revision of the tr101290 MIB module. The date and time here must exactly match one of the… |
| 1.3.6.1.4.1.2696.3.2.1.3.5 | NodecapabilityTS | |||
| 1.3.6.1.4.1.2696.3.2.1.3.5.1 | ScalarcapabilityTSGroup | read-only | current | Specifies the overall availability of the Transport Stream group of tests and measurements, tr101290TS. |
| 1.3.6.1.4.1.2696.3.2.1.3.5.2 | TablecapabilityTSTable | not-accessible | current | Specifies the individual availability of the Transport Stream group of tests and measurements, tr101290TS. |
| 1.3.6.1.4.1.2696.3.2.1.3.5.2.1 | RowcapabilityTSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.3.5.2.1.1 | ColumncapabilityTSOID | not-accessible | current | The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the … |
| 1.3.6.1.4.1.2696.3.2.1.3.5.2.1.2 | ColumncapabilityTSAvailability | read-only | current | The availability of a specific test or measurement |
| 1.3.6.1.4.1.2696.3.2.1.3.5.2.1.3 | ColumncapabilityTSPollInterval | read-only | current | Indicates the interval between updates of the information supplied by this object. |
| 1.3.6.1.4.1.2696.3.2.1.3.6 | NodecapabilityCableSat | |||
| 1.3.6.1.4.1.2696.3.2.1.3.6.1 | ScalarcapabilityCableSatGroup | read-only | current | Specifies the overall availability of the cable and satellite group of tests and measurements, tr101290CableSat. |
| 1.3.6.1.4.1.2696.3.2.1.3.6.2 | TablecapabilityCableSatTable | not-accessible | current | Specifies the individual availability of the cable and satellite group of tests and measurements, tr101290CableSat. |
| 1.3.6.1.4.1.2696.3.2.1.3.6.2.1 | RowcapabilityCableSatEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.3.6.2.1.1 | ColumncapabilityCableSatOID | not-accessible | current | The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the … |
| 1.3.6.1.4.1.2696.3.2.1.3.6.2.1.2 | ColumncapabilityCableSatAvailability | read-only | current | The availability of a specific test or measurement |
| 1.3.6.1.4.1.2696.3.2.1.3.6.2.1.3 | ColumncapabilityCableSatPollInterval | read-only | current | Indicates the interval between updates of the information supplied by this object. |
| 1.3.6.1.4.1.2696.3.2.1.3.7 | NodecapabilityCable | |||
| 1.3.6.1.4.1.2696.3.2.1.3.7.1 | ScalarcapabilityCableGroup | read-only | current | Specifies the overall availability of the cable group of tests and measurements, tr101290Cable. |
| 1.3.6.1.4.1.2696.3.2.1.3.7.2 | TablecapabilityCableTable | not-accessible | current | Specifies the individual availability of the cable group of tests and measurements, tr101290Cable. |
| 1.3.6.1.4.1.2696.3.2.1.3.7.2.1 | RowcapabilityCableEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.3.7.2.1.1 | ColumncapabilityCableOID | not-accessible | current | The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the … |
| 1.3.6.1.4.1.2696.3.2.1.3.7.2.1.2 | ColumncapabilityCableAvailability | read-only | current | The availability of a specific test or measurement |
| 1.3.6.1.4.1.2696.3.2.1.3.7.2.1.3 | ColumncapabilityCablePollInterval | read-only | current | Indicates the interval between updates of the information supplied by this object. |
| 1.3.6.1.4.1.2696.3.2.1.3.8 | NodecapabilitySatellite | |||
| 1.3.6.1.4.1.2696.3.2.1.3.8.1 | ScalarcapabilitySatelliteGroup | read-only | current | Specifies the overall availability of the satellite group of tests and measurements, tr101290Satellite. |
| 1.3.6.1.4.1.2696.3.2.1.3.8.2 | TablecapabilitySatelliteTable | not-accessible | current | Specifies the individual availability of the satellite group of tests and measurements, tr101290Satellite. |
| 1.3.6.1.4.1.2696.3.2.1.3.8.2.1 | RowcapabilitySatelliteEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.3.8.2.1.1 | ColumncapabilitySatelliteOID | not-accessible | current | The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the … |
| 1.3.6.1.4.1.2696.3.2.1.3.8.2.1.2 | ColumncapabilitySatelliteAvailability | read-only | current | The availability of a specific test or measurement |
| 1.3.6.1.4.1.2696.3.2.1.3.8.2.1.3 | ColumncapabilitySatellitePollInterval | read-only | current | Indicates the interval between updates of the information supplied by this object. |
| 1.3.6.1.4.1.2696.3.2.1.3.9 | NodecapabilityTerrestrial | |||
| 1.3.6.1.4.1.2696.3.2.1.3.9.1 | ScalarcapabilityTerrestrialGroup | read-only | current | Specifies the overall availability of the terrestrial group of tests and measurements, tr101290Terrestrial. |
| 1.3.6.1.4.1.2696.3.2.1.3.9.2 | TablecapabilityTerrestrialTable | not-accessible | current | Specifies the individual availability of the terrestrial group of tests and measurements, tr101290Terrestrial. |
| 1.3.6.1.4.1.2696.3.2.1.3.9.2.1 | RowcapabilityTerrestrialEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.3.9.2.1.1 | ColumncapabilityTerrestrialOID | not-accessible | current | The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the … |
| 1.3.6.1.4.1.2696.3.2.1.3.9.2.1.2 | ColumncapabilityTerrestrialAvailability | read-only | current | The availability of a specific test or measurement |
| 1.3.6.1.4.1.2696.3.2.1.3.9.2.1.3 | ColumncapabilityTerrestrialPollInterval | read-only | current | Indicates the interval between updates of the information supplied by this object. |
| 1.3.6.1.4.1.2696.3.2.1.5 | Nodetr101290TS | |||
| 1.3.6.1.4.1.2696.3.2.1.5.2 | NodetsTests | |||
| 1.3.6.1.4.1.2696.3.2.1.5.2.2 | TabletsTestsSummaryTable | not-accessible | current | The tsTestsSummaryTable provides access to the state of all of the Transport Stream tests enumerated in IndexTransportStreamTest. The status relates to the who… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1 | RowtsTestsSummaryEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.1 | ColumntsTestsSummaryInputNumber | not-accessible | current | Transport Stream on which the test is made |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.2 | ColumntsTestsSummaryTestNumber | not-accessible | current | Specifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipmen… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.3 | ColumntsTestsSummaryState | read-only | current | This gives the overall pass/fail state of the test. For tests which have a state per PID, tsTestsSummaryState contains the highest numeric value of all the tsT… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.4 | ColumntsTestsSummaryEnable | read-write | current | Determines whether this test and associated traps are enabled. Setting tsTestsSummaryEnable affects tsTestsPIDEnable in tsTestsPIDTable. When tsTestsSummaryEna… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.5 | ColumntsTestsSummaryCounter | read-only | current | Count of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other st… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.6 | ColumntsTestsSummaryCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsTestsSummaryCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.7 | ColumntsTestsSummaryCounterReset | read-write | current | tsTestsSummaryCounter is reset to zero and tsTestsSummaryCounterDiscontinuity is set to the current time if this object is set to 'true'. This object has no ef… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.8 | ColumntsTestsSummaryLatestError | read-only | current | The timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other s… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.9 | ColumntsTestsSummaryActiveTime | read-only | current | The total time when it has been possible to evaluate this test. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3 | TabletsTestsPIDTable | not-accessible | current | The tsTestsPIDTable provides access to the state of those Transport Stream tests enumerated in IndexTransportStreamTest which relate to individual PIDs. These … |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1 | RowtsTestsPIDEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.1 | ColumntsTestsPIDInputNumber | not-accessible | current | Transport Stream on which the test is made |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.2 | ColumntsTestsPIDPID | not-accessible | current | PID (plus one) on which the test is made |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.3 | ColumntsTestsPIDTestNumber | not-accessible | current | Specifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipmen… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.4 | ColumntsTestsPIDRowStatus | read-create | current | This is used by the manager to create and delete rows in tsTestsPIDTable. The agent automatically creates rows for PID/test combinations where there are errors… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.5 | ColumntsTestsPIDState | read-only | current | This gives the overall pass/fail state of the test |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.6 | ColumntsTestsPIDEnable | read-create | current | Determines whether this test and associated traps are enabled. When a trap triggering condition arises for a per PID test, this object alone is used to determi… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.7 | ColumntsTestsPIDCounter | read-only | current | Count of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other st… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.8 | ColumntsTestsPIDCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsTestsSummaryCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.9 | ColumntsTestsPIDCounterReset | read-create | current | tsTestsPIDCounter is reset to zero and tsTestsPIDCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.10 | ColumntsTestsPIDLatestError | read-only | current | The timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other s… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.11 | ColumntsTestsPIDActiveTime | read-only | current | The total time when it has been possible to evaluate this test. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100 | NodetsTestsPreferences | |||
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1 | TabletsTestsPreferencesTable | not-accessible | current | This table contains measurement thresholds and other configuration information that is applied on a per Transport Stream basis. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1 | RowtsTestsPreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.1 | ColumntsTestsPrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.2 | ColumntsTestsPrefTransitionDuration | read-write | current | Various tests, including CAT_error (2.6) and Unreferenced_PID (3.4) must take into account that short transition periods can exist where the state of the SI an… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.3 | ColumntsTestsPrefPATSectionIntervalMax | read-write | current | Maximum repetition interval for PAT sections. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.4 | ColumntsTestsPrefPMTSectionIntervalMax | read-write | current | Maximum repetition interval for PMT sections. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.5 | ColumntsTestsPrefReferredIntervalMax | read-write | current | Maximum permitted interval between the arrival of consecutive packets for all PIDs. When the value of this object is set, the value of tsTestsPrefPIDReferredIn… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.6 | ColumntsTestsPrefPCRIntervalMax | read-write | current | Maximum permitted interval between PCR arrival times on each PCR PID. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.7 | ColumntsTestsPrefPCRDiscontinuityMax | read-write | current | Maximum permitted difference between two consecutive PCR values. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.8 | ColumntsTestsPrefPCRInaccuracyMax | read-write | current | Maximum permitted PCR inaccuracy. An error is indicated if the PCR inaccuracy is outside the range: [-tsTestsPrefPCRInaccuracyMax .. +tsTestsPrefPCRInaccuracyM… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.9 | ColumntsTestsPrefPTSIntervalMax | read-write | current | Maximum permitted PTS repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.10 | ColumntsTestsPrefNITActualIntervalMax | read-write | current | Maximum permitted NIT_actual section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.11 | ColumntsTestsPrefNITActualIntervalMin | read-write | current | Minimum permitted NIT_actual section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.12 | ColumntsTestsPrefNITOtherIntervalMax | read-write | current | Maximum permitted NIT_other section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.13 | ColumntsTestsPrefSIGapMin | read-write | current | Minimum permitted gap between packets containing sections. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.14 | ColumntsTestsPrefNITTableIntervalMax | read-write | current | Maximum permitted NIT table repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.15 | ColumntsTestsPrefBATTableIntervalMax | read-write | current | Maximum permitted BAT table repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.16 | ColumntsTestsPrefSDTActualTableIntervalMax | read-write | current | Maximum permitted SDT actual transport stream table repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.17 | ColumntsTestsPrefSDTOtherTableIntervalMax | read-write | current | Maximum permitted SDT other transport stream table repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.18 | ColumntsTestsPrefEITPFActualTableIntervalMax | read-write | current | Maximum permitted EIT Present/Following actual transport stream table repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.19 | ColumntsTestsPrefEITPFOtherTableIntervalMax | read-write | current | Maximum permitted EIT Present/Following other transport stream table repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.20 | ColumntsTestsPrefEITSActualNearTableIntervalMax | read-write | current | Maximum permitted EIT Schedule actual transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.21 | ColumntsTestsPrefEITSActualFarTableIntervalMax | read-write | current | Maximum permitted EIT Schedule actual transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the… |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.22 | ColumntsTestsPrefEITSOtherNearTableIntervalMax | read-write | current | Maximum permitted EIT Schedule other transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for … |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.23 | ColumntsTestsPrefEITSOtherFarTableIntervalMax | read-write | current | Maximum permitted EIT Schedule other transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the … |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.24 | ColumntsTestsPrefTxTTableIntervalMax | read-write | current | Maximum permitted TDT and TOT table repetition intervals |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.25 | ColumntsTestsPrefSDTActualIntervalMax | read-write | current | Maximum permitted SDT_actual section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.26 | ColumntsTestsPrefSDTActualIntervalMin | read-write | current | Minimum permitted SDT_actual section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.27 | ColumntsTestsPrefSDTOtherIntervalMax | read-write | current | Maximum permitted SDT_other section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.28 | ColumntsTestsPrefEITActualIntervalMax | read-write | current | Maximum permitted EIT_actual section repetition interval (applies to both present and following sections). |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.29 | ColumntsTestsPrefEITActualIntervalMin | read-write | current | Minimum permitted EIT_actual section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.30 | ColumntsTestsPrefEITOtherIntervalMax | read-write | current | Maximum permitted EIT_other section repetition interval (applies to both present and following sections). |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.31 | ColumntsTestsPrefRSTIntervalMin | read-write | current | Minimum permitted RST section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.32 | ColumntsTestsPrefTDTIntervalMax | read-write | current | Maximum permitted TDT section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.33 | ColumntsTestsPrefTDTIntervalMin | read-write | current | Minimum permitted TDT section repetition interval |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.2 | TabletsTestsPreferencesPIDTable | not-accessible | current | This table contains measurement thresholds and other configuration information that is applied on a per PID per Transport Stream basis. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1 | RowtsTestsPreferencesPIDEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.1 | ColumntsTestsPrefPIDInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.2 | ColumntsTestsPrefPIDPID | not-accessible | current | PID to which these preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.3 | ColumntsTestsPrefPIDRowStatus | read-create | current | This object is used to manage the rows in this table. |
| 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.4 | ColumntsTestsPrefPIDReferredIntervalMax | read-write | current | Maximum permitted interval between the arrival of consecutive packets of this PID. The default value for this object is the current value of tsTestsPrefReferre… |
| 1.3.6.1.4.1.2696.3.2.1.5.4 | NodetsMeasurements | |||
| 1.3.6.1.4.1.2696.3.2.1.5.4.1 | TabletsPcrMeasurementTable | not-accessible | current | This table makes available the PCR_FO, PCR_DR, PCR_OJ and PCR_AC measurements. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1 | RowtsPcrMeasurementEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.1 | ColumntsPcrMeasurementInputNumber | not-accessible | current | Input on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.2 | ColumntsPcrMeasurementPID | not-accessible | current | PID (plus one) in the Transport Stream carrying (or expected to carry) PCRs. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.3 | ColumntsPcrMeasurementNumber | not-accessible | current | This selects one of the four PCR measurements |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.4 | ColumntsPcrMeasurementRowStatus | read-create | current | This object is used by the manager to create and delete rows in the table. The agent automatically creates rows for PIDs where it detects the presence of a PCR. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.5 | ColumntsPcrMeasurementState | read-only | current | This gives the overall pass/fail state of the threshold test on this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.6 | ColumntsPcrMeasurementEnable | read-create | current | Determines whether this test and associated traps are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.7 | ColumntsPcrMeasurementCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.8 | ColumntsPcrMeasurementCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsPcrMeasurementCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.9 | ColumntsPcrMeasurementCounterReset | read-create | current | tsPcrMeasurementCounter is reset to zero and tsPcrMeasurementCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, … |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.10 | ColumntsPcrMeasurementLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.11 | ColumntsPcrMeasurementActiveTime | read-only | current | The total time when it has been possible to make this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.12 | ColumntsPcrMeasurementMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.13 | ColumntsPcrMeasurementValue | read-only | current | The units for the measured value depend on the measurement: PCR_FO Hz PCR_DR Hz/s Values for PCR_OJ and PCR_AC are not provided as they occur too quickly to be… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2 | NodebitRate | |||
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1 | TabletsTransportStreamBitRateTable | not-accessible | current | Bit rates for each complete Transport Stream |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1 | RowtsTransportStreamBitRateEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.1 | ColumntsTransportStreamBitRateInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.2 | ColumntsTransportStreamBitRateState | read-only | current | This gives the overall pass/fail state of the threshold test on this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.3 | ColumntsTransportStreamBitRateEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.4 | ColumntsTransportStreamBitRateCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.5 | ColumntsTransportStreamBitRateCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsTransportStreamBitRateCounterobject. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.6 | ColumntsTransportStreamBitRateCounterReset | read-write | current | tsTransportStreamBitRateCounteris reset to zero and tsTransportStreamBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variab… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.7 | ColumntsTransportStreamBitRateLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.8 | ColumntsTransportStreamBitRateActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.9 | ColumntsTransportStreamBitRateMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.10 | ColumntsTransportStreamBitRateValue | read-only | current | The overall Transport Stream bit rate |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.11 | ColumntsTransportStreamBitRateNomenclature | read-only | current | Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2' |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2 | TabletsServiceBitRateTable | not-accessible | current | Bit rates for each service/program within each Transport Stream. The table is sparse, in that only services mentioned in the PMT will be present. The bit rate … |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1 | RowtsServiceBitRateEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.1 | ColumntsServiceBitRateInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.2 | ColumntsServiceBitRateService | not-accessible | current | The program_number/service_id to which the information in the rest of the row applies. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.3 | ColumntsServiceBitRateRowStatus | read-create | current | This is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.4 | ColumntsServiceBitRateState | read-only | current | This gives the overall pass/fail state of the threshold test on this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.5 | ColumntsServiceBitRateEnable | read-create | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.6 | ColumntsServiceBitRateCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.7 | ColumntsServiceBitRateCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsServiceBitRateCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.8 | ColumntsServiceBitRateCounterReset | read-create | current | tsServiceBitRateCounter is reset to zero and tsServiceBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, … |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.9 | ColumntsServiceBitRateLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.10 | ColumntsServiceBitRateActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.11 | ColumntsServiceBitRateMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.12 | ColumntsServiceBitRateValue | read-only | current | Overall bit rate for the service |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.13 | ColumntsServiceBitRateNomenclature | read-only | current | Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2' |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3 | TabletsPIDBitRateTable | not-accessible | current | Bit rates for each PID within each Transport Stream. The table is sparse, in that only PIDs whose bit rate is currently greater than zero will be present in th… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1 | RowtsPIDBitRateEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.1 | ColumntsPIDBitRateInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.2 | ColumntsPIDBitRatePID | not-accessible | current | PID whose bit rate is being measured (plus one) |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.3 | ColumntsPIDBitRateRowStatus | read-create | current | This is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs whose bit rate is non-zero. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.4 | ColumntsPIDBitRateState | read-only | current | This gives the overall pass/fail state of the threshold test on this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.5 | ColumntsPIDBitRateEnable | read-create | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.6 | ColumntsPIDBitRateCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.7 | ColumntsPIDBitRateCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsPIDBitRateCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.8 | ColumntsPIDBitRateCounterReset | read-create | current | tsPIDBitRateCounter is reset to zero and tsPIDBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the valu… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.9 | ColumntsPIDBitRateLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.10 | ColumntsPIDBitRateActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.11 | ColumntsPIDBitRateMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.12 | ColumntsPIDBitRateValue | read-only | current | Bit rate for the PID. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.13 | ColumntsPIDBitRateNomenclature | read-only | current | Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2' |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3 | TabletsConsistencyTable | not-accessible | current | This table provides the result of the Transport Stream consistency test for each input. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1 | RowtsConsistencyEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.1 | ColumntsConsistencyInputNumber | not-accessible | current | Input (Transport Stream) on which the consistency check is made. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.2 | ColumntsConsistencyTestNumber | not-accessible | current | Specifies the consistency check test |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.3 | ColumntsConsistencyState | read-only | current | This gives the overall pass/fail state of the consistency check. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.4 | ColumntsConsistencyEnable | read-write | current | Determines whether this test and associated traps are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.5 | ColumntsConsistencyCounter | read-only | current | Count of the number of times the consistency check has failed. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.6 | ColumntsConsistencyCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsConsistencyCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.7 | ColumntsConsistencyCounterReset | read-write | current | tsConsistencyCounter is reset to zero and tsConsistencyCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the va… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.8 | ColumntsConsistencyLatestError | read-only | current | The timestamp at the most recent failure of the consistency check. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.9 | ColumntsConsistencyActiveTime | read-only | current | The total time when it has been possible to perform this test |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100 | NodetsMeasurePreferences | |||
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1 | TabletsMeasurePreferencesTable | not-accessible | current | This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to the whole Transport Stream is found here. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1 | RowtsMeasurePreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.1 | ColumntsMeasurePrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.2 | ColumntsMeasurePrefPCRDemarcationFrequency | read-write | current | This is the demarcation frequency used by the PCR measurement system to distinguish between inaccuracy/jitter and drift. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.3 | ColumntsMeasurePrefPCRFOMax | read-write | current | Maximum permitted PCR_FO (frequency offset). An error is indicated if the measured PCR_FO is outside the range [-tsMeasurePrefPCRFOMax .. +tsMeasurePrefPCRFOMa… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.4 | ColumntsMeasurePrefPCRDRMax | read-write | current | Maximum permitted PCR_DR (drift rate). An error is indicated if the measured PCR_DR is outside the range [-tsMeasurePrefPCRDRMax .. +tsMeasurePrefPCRDRMax] |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.5 | ColumntsMeasurePrefPCROJMax | read-write | current | Maximum permitted PCR_OJ (overall jitter). An error is indicated if the measured PCR_OJ is outside the range [-tsMeasurePrefPCROJMax .. +tsMeasurePrefPCROJMax] |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.6 | ColumntsMeasurePrefTSBitRateTau | read-write | current | 'tau' value for Transport Stream bit rate measurement. The MIB provides very flexible ways of setting the bit rate measurement parameters tau, N and element fo… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.7 | ColumntsMeasurePrefTSBitRateN | read-write | current | 'N' value for Transport Stream bit rate measurement. See note in description for tsMeasurePrefTSBitRateTau. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.8 | ColumntsMeasurePrefTSBitRateElement | read-write | current | Data unit which is counted by the bit rate measurement algorithm. See note in description for tsMeasurePrefTSBitRateTau. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.9 | ColumntsMeasurePrefTSBitRateMin | read-write | current | An error is generated if the Transport Stream bit rate is below this value. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.10 | ColumntsMeasurePrefTSBitRateMax | read-write | current | An error is generated if the Transport Stream bit rate exceeds this value. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.11 | ColumntsMeasurePrefAllServiceBitRateTau | read-write | current | 'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateTau columns in all the… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.12 | ColumntsMeasurePrefAllServiceBitRateN | read-write | current | 'N' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateN columns in all the row… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.13 | ColumntsMeasurePrefAllServiceBitRateElement | read-write | current | Data unit which is counted by the bit rate measurement algorithm for services. When a manager sets the value of this object, the values of the tsMeasurePrefSer… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.14 | ColumntsMeasurePrefAllPIDBitRateTau | read-write | current | 'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateTau columns in all the row… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.15 | ColumntsMeasurePrefAllPIDBitRateN | read-write | current | 'N' value for PID bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateN columns in all the rows of the… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.16 | ColumntsMeasurePrefAllPIDBitRateElement | read-write | current | Data unit which is counted by the bit rate measurement algorithm for PIDs. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitR… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.17 | ColumntsMeasurePrefExpectedTSID | read-write | current | This object defines the expected Transport Stream ID that is compared with the actual ID to perform the consistency of information check. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2 | TabletsMeasurePreferencesServiceTable | not-accessible | current | This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual services is found here. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1 | RowtsMeasurePreferencesServiceEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.1 | ColumntsMeasurePrefServiceInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.2 | ColumntsMeasurePrefServiceService | not-accessible | current | Service to which the preferences apply. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.3 | ColumntsMeasurePrefServiceRowStatus | read-create | current | This is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.4 | ColumntsMeasurePrefServiceBitRateTau | read-create | current | 'tau' value for bit rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service tau sett… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.5 | ColumntsMeasurePrefServiceBitRateN | read-create | current | 'N' value for rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service 'N' settings, … |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.6 | ColumntsMeasurePrefServiceBitRateElement | read-create | current | Data unit which is counted by the bit rate measurement algorithm for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not … |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.7 | ColumntsMeasurePrefServiceBitRateMin | read-create | current | An error is generated if the Service bit rate is below this value. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.8 | ColumntsMeasurePrefServiceBitRateMax | read-create | current | An error is generated if the Transport Stream bit rate exceeds this value. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3 | TabletsMeasurePreferencesPIDTable | not-accessible | current | This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual PIDs is found here. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1 | RowtsMeasurePreferencesPIDEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.1 | ColumntsMeasurePrefPIDInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.2 | ColumntsMeasurePrefPIDPID | not-accessible | current | PID (plus one) to which the preferences apply. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.3 | ColumntsMeasurePrefPIDRowStatus | read-create | current | This is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs which have a non-zero bit rate. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.4 | ColumntsMeasurePrefPIDBitRateTau | read-create | current | 'tau' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID tau settings, it… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.5 | ColumntsMeasurePrefPIDBitRateN | read-create | current | 'N' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID 'N' settings, it s… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.6 | ColumntsMeasurePrefPIDBitRateElement | read-create | current | Data unit which is counted by the bit rate measurement algorithm for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not supp… |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.7 | ColumntsMeasurePrefPIDBitRateMin | read-create | current | An error is generated if the PID bit rate is below this value. |
| 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.8 | ColumntsMeasurePrefPIDBitRateMax | read-create | current | An error is generated if the PID bit rate exceeds this value. |
| 1.3.6.1.4.1.2696.3.2.1.5.5 | NodetsServicePerformance | |||
| 1.3.6.1.4.1.2696.3.2.1.5.5.2 | TabletsServicePerformanceTable | not-accessible | current | This table gives access to the Service Performance measurements and tests |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1 | RowtsServicePerformanceEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.1 | ColumntsServicePerformanceInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.2 | ColumntsServicePerformanceNumber | not-accessible | current | The Service Performance measurement which this row applies to. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.3 | ColumntsServicePerformanceState | read-only | current | This gives the overall pass/fail state of the threshold test on this measurement. The threshold test fails if the value of tsServicePerformanceErrorRatio excee… |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.4 | ColumntsServicePerformanceEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.5 | ColumntsServicePerformanceCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.6 | ColumntsServicePerformanceCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the tsServicePerformanceCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.7 | ColumntsServicePerformanceCounterReset | read-write | current | tsServicePerformanceCounter is reset to zero and tsServicePerformanceCounterDiscontinuity is set to the current time if 'true' is written to this variable. The… |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.8 | ColumntsServicePerformanceLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.9 | ColumntsServicePerformanceActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.10 | ColumntsServicePerformanceMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.11 | ColumntsServicePerformanceError | read-only | current | The calculated xxx_Error parameter as measured at the end of the most recently completed DeltaT period. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.12 | ColumntsServicePerformanceErrorRatio | read-only | current | This is the calculated xxx_Error_Ratio as a percentage (e.g. '1.32'). The value is for the most recently completed evaluation time (e.g. 10 minutes). |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100 | TabletsServicePerformancePreferencesTable | not-accessible | current | Parameters controlling the Service Performance measurements |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100.1 | RowtsServicePerformancePreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.1 | ColumntsSPPrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.2 | ColumntsSPPrefNumber | not-accessible | current | The service performance parameter to which these preferences apply. |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.3 | ColumntsSPPrefDeltaT | read-write | current | The defined time interval over which errors are counted |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.4 | ColumntsSPPrefEvaluationTime | read-write | current | The period over which the ...Error_Ratio is calculated |
| 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.5 | ColumntsSPPrefThreshold | read-write | current | The threshold value used in calculating the ..._Error_Ratio. |
| 1.3.6.1.4.1.2696.3.2.1.6 | Nodetr101290CableSat | |||
| 1.3.6.1.4.1.2696.3.2.1.6.1 | TablesysAvailabilityTable | not-accessible | current | System availability measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1 | RowsysAvailabilityEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.1 | ColumnsysAvailabilityInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.2 | ColumnsysAvailabilityTestState | read-only | current | A 'fail' is an approximate indication that the system is in a period of unavailable time (UAT). 'fail' is indicated as soon as a trigger period for unavailable… |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.3 | ColumnsysAvailabilityEnable | read-write | current | Determines whether system availability testing is performed and whether the associated traps are generated. |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.4 | ColumnsysAvailabilityCounter | read-only | current | Count of the number of times the system has become unavailable |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.5 | ColumnsysAvailabilityCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the sysAvailabilityCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.6 | ColumnsysAvailabilityCounterReset | read-write | current | sysAvailabilityCounter is reset to zero and sysAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, th… |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.7 | ColumnsysAvailabilityLatestError | read-only | current | The timestamp when the system most recently became unavailable. |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.8 | ColumnsysAvailabilityActiveTime | read-only | current | This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the tes… |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.9 | ColumnsysAvailabilityMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.10 | ColumnsysAvailabilityUnavailableTime | read-only | current | This is a monotonically increasing time in seconds which measures the total Unavailable Time (UAT) since the measuring system was last restarted. |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.11 | ColumnsysAvailabilityRatio | read-only | current | This is the System Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period. |
| 1.3.6.1.4.1.2696.3.2.1.6.1.1.12 | ColumnsysAvailabilityInSETI | read-only | current | This object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Errored Time Interval (SETI). |
| 1.3.6.1.4.1.2696.3.2.1.6.2 | TablelinkAvailabilityTable | not-accessible | current | Link availability measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1 | RowlinkAvailabilityEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.1 | ColumnlinkAvailabilityInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.2 | ColumnlinkAvailabilityTestState | read-only | current | A 'fail' is an approximate indication that the system is in a period of link unavailable time (LUAT). 'fail' is indicated as soon as a trigger period for link … |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.3 | ColumnlinkAvailabilityEnable | read-write | current | Determines whether link availability testing is performed and whether the associated traps are generated. |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.4 | ColumnlinkAvailabilityCounter | read-only | current | Count of the number of times the link has become unavailable. |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.5 | ColumnlinkAvailabilityCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the linkAvailabilityCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.6 | ColumnlinkAvailabilityCounterReset | read-write | current | linkAvailabilityCounter is reset to zero and linkAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, … |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.7 | ColumnlinkAvailabilityLatestError | read-only | current | The timestamp when the link most recently became unavailable. |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.8 | ColumnlinkAvailabilityActiveTime | read-only | current | This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the mea… |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.9 | ColumnlinkAvailabilityMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.10 | ColumnlinkAvailabilityUnavailableTime | read-only | current | This is a monotonically increasing time in seconds which measures the total link unavailable time (LUAT) since the measuring system was last restarted. |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.11 | ColumnlinkAvailabilityRatio | read-only | current | This is the Link Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period. |
| 1.3.6.1.4.1.2696.3.2.1.6.2.1.12 | ColumnlinkAvailabilityInSUTI | read-only | current | This object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Uncorrectable Time Interval (SETI). |
| 1.3.6.1.4.1.2696.3.2.1.6.3 | TableberRSinServiceTable | not-accessible | current | Measurement of BER before RS decoder |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1 | RowberRSinServiceEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.1 | ColumnberRSinServiceInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.2 | ColumnberRSinServiceTestState | read-only | current | This indicates whether the berRSinServiceValue is below the maximum. |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.3 | ColumnberRSinServiceEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.4 | ColumnberRSinServiceCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.5 | ColumnberRSinServiceCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the berRSinServiceCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.6 | ColumnberRSinServiceCounterReset | read-write | current | berRSinServiceCounter is reset to zero and berRSinServiceCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the va… |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.7 | ColumnberRSinServiceLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.8 | ColumnberRSinServiceActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.9 | ColumnberRSinServiceMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.3.1.10 | ColumnberRSinServiceValue | read-only | current | This is the current BER as a numeric value, for example 0.0000023 |
| 1.3.6.1.4.1.2696.3.2.1.6.6 | TablerfIFsignalPowerTable | not-accessible | current | RF or IF signal power measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1 | RowrfIFsignalPowerEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.1 | ColumnrfIFsignalPowerInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.2 | ColumnrfIFsignalPowerTestState | read-only | current | This indicates whether the rfIFsignalPowerValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.3 | ColumnrfIFsignalPowerEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.4 | ColumnrfIFsignalPowerCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.5 | ColumnrfIFsignalPowerCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the rfIFsignalPowerCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.6 | ColumnrfIFsignalPowerCounterReset | read-write | current | rfIFsignalPowerCounter is reset to zero and rfIFsignalPowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the … |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.7 | ColumnrfIFsignalPowerLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.8 | ColumnrfIFsignalPowerActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.9 | ColumnrfIFsignalPowerMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.6.1.10 | ColumnrfIFsignalPowerValue | read-only | current | The current RF power expressed in dBm, which references 0 dBm as the power of 1 mW. |
| 1.3.6.1.4.1.2696.3.2.1.6.7 | TablenoisePowerTable | not-accessible | current | Noise power measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1 | RownoisePowerEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.1 | ColumnnoisePowerInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.2 | ColumnnoisePowerTestState | read-only | current | This indicates whether the noisePowerValue is currently below the maximum limit. |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.3 | ColumnnoisePowerEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.4 | ColumnnoisePowerCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.5 | ColumnnoisePowerCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the noisePowerCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.6 | ColumnnoisePowerCounterReset | read-write | current | noisePowerCounter is reset to zero and noisePowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of t… |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.7 | ColumnnoisePowerLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.8 | ColumnnoisePowerActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.9 | ColumnnoisePowerMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.7.1.10 | ColumnnoisePowerValue | read-only | current | The current RF noise power expressed in dBm, which references 0 dBm as the power of 1 mW. |
| 1.3.6.1.4.1.2696.3.2.1.6.9 | NodeiqAnalysisCS | |||
| 1.3.6.1.4.1.2696.3.2.1.6.9.2 | TablemerCSTable | not-accessible | current | Modulation Error Ratio (MER) |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1 | RowmerCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.1 | ColumnmerCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.2 | ColumnmerCSTestState | read-only | current | This indicates whether the merCSValue is currently below the maximum limit. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.3 | ColumnmerCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.4 | ColumnmerCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.5 | ColumnmerCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the merCSCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.6 | ColumnmerCSCounterReset | read-write | current | merCSCounter is reset to zero and merCSCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.7 | ColumnmerCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.8 | ColumnmerCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.9 | ColumnmerCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.10 | ColumnmerCSValue | read-only | current | The Modulation Error Ratio expressed in dB |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3 | NodesteCS | |||
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1 | TablesteMeanCSTable | not-accessible | current | System Target Error (mean value) |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1 | RowsteMeanCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.1 | ColumnsteMeanCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.2 | ColumnsteMeanCSTestState | read-only | current | This indicates whether the steMeanCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.3 | ColumnsteMeanCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.4 | ColumnsteMeanCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.5 | ColumnsteMeanCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.6 | ColumnsteMeanCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.7 | ColumnsteMeanCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.8 | ColumnsteMeanCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.9 | ColumnsteMeanCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.10 | ColumnsteMeanCSValue | read-only | current | The current System Target Error Mean as a numeric value |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2 | TablesteDeviationCSTable | not-accessible | current | System Target Error (deviation value) |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1 | RowsteDeviationCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.1 | ColumnsteDeviationCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.2 | ColumnsteDeviationCSTestState | read-only | current | This indicates whether the steDeviationCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.3 | ColumnsteDeviationCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.4 | ColumnsteDeviationCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.5 | ColumnsteDeviationCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.6 | ColumnsteDeviationCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.7 | ColumnsteDeviationCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.8 | ColumnsteDeviationCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.9 | ColumnsteDeviationCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.10 | ColumnsteDeviationCSValue | read-only | current | The current System Target Error Deviation as a numeric value |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4 | TablecsCSTable | not-accessible | current | Carrier suppression measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1 | RowcsCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.1 | ColumncsCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.2 | ColumncsCSTestState | read-only | current | This indicates whether the csCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.3 | ColumncsCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.4 | ColumncsCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.5 | ColumncsCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.6 | ColumncsCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.7 | ColumncsCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.8 | ColumncsCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.9 | ColumncsCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.10 | ColumncsCSValue | read-only | current | The current Carrier Suppression value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5 | TableaiCSTable | not-accessible | current | Amplitude Imbalance (AI) measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1 | RowaiCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.1 | ColumnaiCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.2 | ColumnaiCSTestState | read-only | current | This indicates whether the aiCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.3 | ColumnaiCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.4 | ColumnaiCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.5 | ColumnaiCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.6 | ColumnaiCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.7 | ColumnaiCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.8 | ColumnaiCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.9 | ColumnaiCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.10 | ColumnaiCSValue | read-only | current | The current Amplitude Imbalance as a percentage |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6 | TableqeCSTable | not-accessible | current | Quadrature Error (QE) measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1 | RowqeCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.1 | ColumnqeCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.2 | ColumnqeCSTestState | read-only | current | This indicates whether the qeCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.3 | ColumnqeCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.4 | ColumnqeCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.5 | ColumnqeCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.6 | ColumnqeCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.7 | ColumnqeCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.8 | ColumnqeCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.9 | ColumnqeCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.10 | ColumnqeCSValue | read-only | current | The current Quadrature Error value in degrees. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7 | TablerteCSTable | not-accessible | current | Residual Target Error (RTE) measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1 | RowrteCSEntry | not-accessible | current | Row description |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.1 | ColumnrteCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.2 | ColumnrteCSTestState | read-only | current | This indicates whether the rteCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.3 | ColumnrteCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.4 | ColumnrteCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.5 | ColumnrteCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.6 | ColumnrteCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.7 | ColumnrteCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.8 | ColumnrteCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.9 | ColumnrteCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.10 | ColumnrteCSValue | read-only | current | The current Residual Target Error value as a numeric value. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8 | TableciCSTable | not-accessible | current | Coherent Interferer measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1 | RowciCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.1 | ColumnciCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.2 | ColumnciCSTestState | read-only | current | This indicates whether the ciCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.3 | ColumnciCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.4 | ColumnciCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.5 | ColumnciCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.6 | ColumnciCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.7 | ColumnciCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.8 | ColumnciCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.9 | ColumnciCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.10 | ColumnciCSValue | read-only | current | The current Coherent Interferer value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9 | TablepjCSTable | not-accessible | current | Phase Jitter (PJ) measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1 | RowpjCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.1 | ColumnpjCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.2 | ColumnpjCSTestState | read-only | current | This indicates whether the pjCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.3 | ColumnpjCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.4 | ColumnpjCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.5 | ColumnpjCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.6 | ColumnpjCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.7 | ColumnpjCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.8 | ColumnpjCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.9 | ColumnpjCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.10 | ColumnpjCSValue | read-only | current | The current Phase Jitter value in degrees. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10 | TablesnrCSTable | not-accessible | current | Signal-to-Noise Ratio (SNR) |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1 | RowsnrCSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.1 | ColumnsnrCSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.2 | ColumnsnrCSTestState | read-only | current | This indicates whether the snrCSValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.3 | ColumnsnrCSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.4 | ColumnsnrCSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.5 | ColumnsnrCSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.6 | ColumnsnrCSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.7 | ColumnsnrCSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.8 | ColumnsnrCSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.9 | ColumnsnrCSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.10 | ColumnsnrCSValue | read-only | current | The current Signal-to-Noise value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.6.100 | TablecableSatPreferencesTable | not-accessible | current | Table containing per input configuration information for cable and satellite common measurements. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1 | RowcableSatPreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.1 | ColumncableSatPrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.2 | ColumncableSatPrefCentreFrequency | read-write | current | This is the centre frequency to which the measuring equipment is tuned for making cable and satellite measurements. This frequency is the actual input frequenc… |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.3 | ColumncableSatPrefModulation | read-write | current | This is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to cable and satellite mea… |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.4 | ColumncableSatPrefSysAvailUATMode | read-write | current | Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' … |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.5 | ColumncableSatPrefSysAvailN | read-write | current | The N value used to identify the start and end of a period of unavailable time (UAT). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.6 | ColumncableSatPrefSysAvailT | read-write | current | The T value used to identify the start and end of a period of unavailable time (UAT). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.7 | ColumncableSatPrefSysAvailM | read-write | current | The M value used to identify the start and end of a period of unavailable time (UAT). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.8 | ColumncableSatPrefSysAvailTI | read-write | current | Each Time Interval of this length is assessed as to whether it is a Severely Errored Time Interval. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.9 | ColumncableSatPrefSysAvailEBPerCent | read-write | current | If more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values… |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.10 | ColumncableSatPrefSysAvailTotalTime | read-write | current | The Total Time over which the System Availability is calculated. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.11 | ColumncableSatPrefLinkAvailUATMode | read-write | current | Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Link Unavailable Time (LUAT) is used. If the 'N consecu… |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.12 | ColumncableSatPrefLinkAvailN | read-write | current | The N value used to identify the start and end of a period of Link Unavailable Time (LUAT). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.13 | ColumncableSatPrefLinkAvailT | read-write | current | The T value used to identify the start and end of a period of Link Unavailable Time (LUAT). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.14 | ColumncableSatPrefLinkAvailM | read-write | current | The M value used to identify the start and end of a period of Link Unavailable Time (LUAT). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.15 | ColumncableSatPrefLinkAvailTI | read-write | current | Each Time Interval of this length is assessed as to whether it is a Severely Uncorrectable Time Interval (SUTI). |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.16 | ColumncableSatPrefLinkAvailUPPerCent | read-write | current | If more than this percentage of packets within a Time Interval is an Uncorrectable Packet (UP), the Time Interval is a Severely Uncorrectable Time Interval (SU… |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.17 | ColumncableSatPrefLinkAvailTotalTime | read-write | current | The Total Time over which the Link Availability is calculated. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.18 | ColumncableSatPrefBERMax | read-write | current | If the berRSinServiceValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.19 | ColumncableSatPrefSignalPowerMin | read-write | current | If the power measured by rfIFsignalPowerValue is less than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.20 | ColumncableSatPrefSignalPowerMax | read-write | current | If the power measured by rfIFsignalPowerValue is greater than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.21 | ColumncableSatPrefNoisePowerMax | read-write | current | If the noise power measured by noisePowerValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.22 | ColumncableSatPrefMerCSMin | read-write | current | If the merCSValue is less than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.23 | ColumncableSatPrefSteMeanCSMax | read-write | current | If the steMeanCSValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.24 | ColumncableSatPrefSteDeviationCSMax | read-write | current | If the steDeviationCSValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.25 | ColumncableSatPrefCsCSMin | read-write | current | If the csCSValue is less than this value, the associated test fails |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.26 | ColumncableSatPrefAiCSMax | read-write | current | If aiCSValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.27 | ColumncableSatPrefQeCSMax | read-write | current | If qeCSValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.28 | ColumncableSatPrefRteCSMax | read-write | current | If rteCSValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.29 | ColumncableSatPrefCiCSMin | read-write | current | If ciCSValue is less than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.30 | ColumncableSatPrefPjCSMax | read-write | current | If pjCSValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.6.100.1.31 | ColumncableSatPrefSnrCSMin | read-write | current | If snrCSValue is less than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.7 | Nodetr101290Cable | |||
| 1.3.6.1.4.1.2696.3.2.1.7.1 | TablenoiseMarginTable | not-accessible | current | Noise margin measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1 | RownoiseMarginEntry | not-accessible | current | Row description |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.1 | ColumnnoiseMarginInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.2 | ColumnnoiseMarginTestState | read-only | current | This indicates whether the noiseMarginValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.3 | ColumnnoiseMarginEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.4 | ColumnnoiseMarginCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.5 | ColumnnoiseMarginCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.6 | ColumnnoiseMarginCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.7 | ColumnnoiseMarginLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.8 | ColumnnoiseMarginActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.9 | ColumnnoiseMarginMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.1.1.10 | ColumnnoiseMarginValue | read-only | current | The current Noise Margin value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.7.2 | TableestNoiseMarginTable | not-accessible | current | Estimated noise margin measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1 | RowestNoiseMarginEntry | not-accessible | current | Row description |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.1 | ColumnestNoiseMarginInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.2 | ColumnestNoiseMarginTestState | read-only | current | This indicates whether the estNoiseMarginValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.3 | ColumnestNoiseMarginEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.4 | ColumnestNoiseMarginCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.5 | ColumnestNoiseMarginCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.6 | ColumnestNoiseMarginCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.7 | ColumnestNoiseMarginLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.8 | ColumnestNoiseMarginActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.9 | ColumnestNoiseMarginMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.2.1.10 | ColumnestNoiseMarginValue | read-only | current | The current Estimated Noise Margin value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.7.3 | TablesignQualMarTTable | not-accessible | current | Signal quality margin test |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1 | RowsignQualMarTEntry | not-accessible | current | Row description |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.1 | ColumnsignQualMarTInputNumber | not-accessible | current | Transport Stream on which the test is done |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.2 | ColumnsignQualMarTTestState | read-only | current | This indicates an error if the percentage of IQ points outside the threshold box exceeds cablePrefSignQualPercentMax. |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.3 | ColumnsignQualMarTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.4 | ColumnsignQualMarTCounter | read-only | current | Count of the number of times an error has occurred. |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.5 | ColumnsignQualMarTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.6 | ColumnsignQualMarTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.7 | ColumnsignQualMarTLatestError | read-only | current | The timestamp at the most recent occurrence of an error. |
| 1.3.6.1.4.1.2696.3.2.1.7.3.1.8 | ColumnsignQualMarTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.4 | TableeNDCTable | not-accessible | current | Equivalent Noise Degradation (END) measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1 | RoweNDCEntry | not-accessible | current | Row description |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.1 | ColumneNDCInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.2 | ColumneNDCTestState | read-only | current | This indicates an error when the eNDCValue exceeds the threshold. |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.3 | ColumneNDCEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.4 | ColumneNDCCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.5 | ColumneNDCCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.6 | ColumneNDCCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.7 | ColumneNDCLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.8 | ColumneNDCActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.9 | ColumneNDCMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.4.1.10 | ColumneNDCValue | read-only | current | The current Equivalent Noise Degradation value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.7.5 | TableoutBandEmissTable | not-accessible | current | Out of band emissions test |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1 | RowoutBandEmissEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.1 | ColumnoutBandEmissInputNumber | not-accessible | current | Transport Stream on which the test is made |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.2 | ColumnoutBandEmissTestState | read-only | current | This indicates whether the spectrum is within the spectrum mask. Note that the spectrum mask must be provided to the instrument by means outside the scope of t… |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.3 | ColumnoutBandEmissEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.4 | ColumnoutBandEmissCounter | read-only | current | Count of the number of times an error has occurred for this test. |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.5 | ColumnoutBandEmissCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.6 | ColumnoutBandEmissCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.7 | ColumnoutBandEmissLatestError | read-only | current | The timestamp at the most recent occurrence of an error on this test. |
| 1.3.6.1.4.1.2696.3.2.1.7.5.1.8 | ColumnoutBandEmissActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.7.100 | TablecablePreferencesTable | not-accessible | current | Table containing per input preferences for cable measurements. |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1 | RowcablePreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.1 | ColumncablePrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.2 | ColumncablePrefNoiseMarginMin | read-write | current | If the measured noiseMarginValue is less than this value the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.3 | ColumncablePrefEstNoiseMarginMin | read-write | current | If the measured estNoiseMarginValue is less than this value the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.4 | ColumncablePrefSignQualBoxSize | read-write | current | This object determines the size of the quality threshold box for the signal quality margin test. The quality threshold box is assumed to be square. The value i… |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.5 | ColumncablePrefSignQualPercentMax | read-write | current | This object sets the limit on how many constellation points may fall outside the threshold box before the signal quality margin test fails. The value is expres… |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.6 | ColumncablePrefENDBER | read-write | current | BER value which is to be used for the END measurement. |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.7 | ColumncablePrefENDCtoNSpecified | read-write | current | This determines whether cablePrefENDIdeal is expressed as a C/N ratio (value is true) or an Eb/No ratio (value is false). |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.8 | ColumncablePrefENDIdeal | read-write | current | This is the 'ideal' value of C/N or Eb/No for the given BER. |
| 1.3.6.1.4.1.2696.3.2.1.7.100.1.9 | ColumncablePrefENDMax | read-write | current | If the measured END exceeds this value the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.8 | Nodetr101290Satellite | |||
| 1.3.6.1.4.1.2696.3.2.1.8.1 | TableberViterbiSTable | not-accessible | current | BER before Viterbi decoding measurement |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1 | RowberViterbiSEntry | not-accessible | current | Row description |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.1 | ColumnberViterbiSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.2 | ColumnberViterbiSTestState | read-only | current | This test fails if either berViterbiSIValue or berViterbiSQValue exceeds the threshold set by satellitePrefBERMax. |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.3 | ColumnberViterbiSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.4 | ColumnberViterbiSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.5 | ColumnberViterbiSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the berViterbiSCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.6 | ColumnberViterbiSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.7 | ColumnberViterbiSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.8 | ColumnberViterbiSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.9 | ColumnberViterbiSMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.10 | ColumnberViterbiSIValue | read-only | current | This is the pre-Viterbi I path BER value, for example 0.0000023 |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.11 | ColumnberViterbiSQValue | read-only | current | This is the pre-Viterbi Q path BER value, for example 0.0000023 |
| 1.3.6.1.4.1.2696.3.2.1.8.1.1.12 | ColumnberViterbiSMeasurementMethod | read-only | current | This indicates whether the measurement was made separately for the I and Q parts of the signal or by a measurement of I and Q combined. |
| 1.3.6.1.4.1.2696.3.2.1.8.2 | TableifSpectrumTable | not-accessible | current | IF spectrum test |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1 | RowifSpectrumEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.1 | ColumnifSpectrumInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.2 | ColumnifSpectrumTestState | read-only | current | This indicates whether the spectrum conforms to the template. Note that the spectrum mask must be provided to the instrument by means outside the scope of this… |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.3 | ColumnifSpectrumEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.4 | ColumnifSpectrumCounter | read-only | current | Count of the number of times an error has occurred for this test. |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.5 | ColumnifSpectrumCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.6 | ColumnifSpectrumCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.7 | ColumnifSpectrumLatestError | read-only | current | The timestamp at the most recent occurrence of an error on this test. |
| 1.3.6.1.4.1.2696.3.2.1.8.2.1.8 | ColumnifSpectrumActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.8.100 | TablesatellitePreferencesTable | not-accessible | current | Table of satellite specific measurement preferences. |
| 1.3.6.1.4.1.2696.3.2.1.8.100.1 | RowsatellitePreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.8.100.1.1 | ColumnsatellitePrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.8.100.1.2 | ColumnsatellitePrefBERMax | read-write | current | This defines the upper limit on the BER before Viterbi measurement |
| 1.3.6.1.4.1.2696.3.2.1.9 | Nodetr101290Terrestrial | |||
| 1.3.6.1.4.1.2696.3.2.1.9.1 | NoderfTerr | |||
| 1.3.6.1.4.1.2696.3.2.1.9.1.1 | TablerfAccuracyTable | not-accessible | current | RF frequency accuracy (Precision) |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1 | RowrfAccuracyEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.1 | ColumnrfAccuracyInputNumber | not-accessible | current | RF input on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.2 | ColumnrfAccuracyTestState | read-only | current | This indicates whether the rfAccuracyValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.3 | ColumnrfAccuracyEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.4 | ColumnrfAccuracyCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.5 | ColumnrfAccuracyCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.6 | ColumnrfAccuracyCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.7 | ColumnrfAccuracyLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.8 | ColumnrfAccuracyActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.9 | ColumnrfAccuracyMeasurementState | read-only | current | Indicates the validity of the measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.10 | ColumnrfAccuracyValue | read-only | current | This is the RF carrier frequency in Hz. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2 | TablerfChannelWidthTable | not-accessible | current | RF channel width (Sampling Frequency Accuracy) |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1 | RowrfChannelWidthEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.1 | ColumnrfChannelWidthInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.2 | ColumnrfChannelWidthTestState | read-only | current | This indicates whether the rfChannelWidthValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.3 | ColumnrfChannelWidthEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.4 | ColumnrfChannelWidthCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.5 | ColumnrfChannelWidthCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.6 | ColumnrfChannelWidthCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.7 | ColumnrfChannelWidthLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.8 | ColumnrfChannelWidthActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.9 | ColumnrfChannelWidthMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.10 | ColumnrfChannelWidthValue | read-only | current | This is the RF channel width in Hz. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3 | TablesymbolLengthTable | not-accessible | current | Symbol Length measurement at RF (Guard Interval verification) |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1 | RowsymbolLengthEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.1 | ColumnsymbolLengthInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.2 | ColumnsymbolLengthTestState | read-only | current | This indicates whether the symbolLengthValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.3 | ColumnsymbolLengthEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.4 | ColumnsymbolLengthCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.5 | ColumnsymbolLengthCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.6 | ColumnsymbolLengthCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.7 | ColumnsymbolLengthLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.8 | ColumnsymbolLengthActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.9 | ColumnsymbolLengthMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.10 | ColumnsymbolLengthValue | read-only | current | This is the symbol length in microseconds. |
| 1.3.6.1.4.1.2696.3.2.1.9.5 | TablerfIfPowerTable | not-accessible | current | RF/IF signal power |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1 | RowrfIfPowerEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.1 | ColumnrfIfPowerInputNumber | not-accessible | current | RF input on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.2 | ColumnrfIfPowerTestState | read-only | current | This indicates whether the rfIfPowerValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.3 | ColumnrfIfPowerEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.4 | ColumnrfIfPowerCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.5 | ColumnrfIfPowerCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.6 | ColumnrfIfPowerCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.7 | ColumnrfIfPowerLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.8 | ColumnrfIfPowerActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.9 | ColumnrfIfPowerMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.5.1.10 | ColumnrfIfPowerValue | read-only | current | The current RF power expressed in dBm, which references 0 dBm as the power of 1 mW. |
| 1.3.6.1.4.1.2696.3.2.1.9.7 | TablerfIfSpectrumTable | not-accessible | current | RF and IF spectrum mask test |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1 | RowrfIfSpectrumEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.1 | ColumnrfIfSpectrumInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.2 | ColumnrfIfSpectrumTestState | read-only | current | This indicates whether the signal conforms to the spectrum mask |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.3 | ColumnrfIfSpectrumEnable | read-write | current | Determines whether the spectrum mask test and the associated trap are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.4 | ColumnrfIfSpectrumCounter | read-only | current | Count of the number of times an error has occurred. |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.5 | ColumnrfIfSpectrumCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.6 | ColumnrfIfSpectrumCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.7 | ColumnrfIfSpectrumLatestError | read-only | current | The timestamp at the most recent occurrence of an error. |
| 1.3.6.1.4.1.2696.3.2.1.9.7.1.8 | ColumnrfIfSpectrumActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.9 | NodeeNDT | |||
| 1.3.6.1.4.1.2696.3.2.1.9.9.1 | TableeNDTTable | not-accessible | current | Equivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If … |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1 | RoweNDTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.1 | ColumneNDTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.2 | ColumneNDTTestState | read-only | current | This indicates whether eNDTValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.3 | ColumneNDTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.4 | ColumneNDTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.5 | ColumneNDTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.6 | ColumneNDTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.7 | ColumneNDTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.8 | ColumneNDTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.9 | ColumneNDTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.10 | ColumneNDTValue | read-only | current | The current Equivalent Noise Degradation expressed in dB. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2 | TableeNFTTable | not-accessible | current | Equivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the tr… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1 | RoweNFTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.1 | ColumneNFTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.2 | ColumneNFTTestState | read-only | current | This indicates whether the eNFTValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.3 | ColumneNFTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.4 | ColumneNFTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.5 | ColumneNFTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.6 | ColumneNFTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.7 | ColumneNFTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.8 | ColumneNFTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.9 | ColumneNFTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.10 | ColumneNFTValue | read-only | current | The current Equivalent Noise Floor expressed in dB, see the reference for the method of calculation. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3 | TableeNDTLPTable | not-accessible | current | Equivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If t… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1 | RoweNDTLPEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.1 | ColumneNDTLPInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.2 | ColumneNDTLPTestState | read-only | current | This indicates whether eNDTLPValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.3 | ColumneNDTLPEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.4 | ColumneNDTLPCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.5 | ColumneNDTLPCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.6 | ColumneNDTLPCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.7 | ColumneNDTLPLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.8 | ColumneNDTLPActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.9 | ColumneNDTLPMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.10 | ColumneNDTLPValue | read-only | current | The current Equivalent Noise Degradation for the low priority stream expressed in dB. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4 | TableeNFTLPTable | not-accessible | current | Equivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the tra… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1 | RoweNFTLPEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.1 | ColumneNFTLPInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.2 | ColumneNFTLPTestState | read-only | current | This indicates whether eNFTLPValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.3 | ColumneNFTLPEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.4 | ColumneNFTLPCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.5 | ColumneNFTLPCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.6 | ColumneNFTLPCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.7 | ColumneNFTLPLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.8 | ColumneNFTLPActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.9 | ColumneNFTLPMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.10 | ColumneNFTLPValue | read-only | current | The current Equivalent Noise Floor for the low priority stream, expressed in dB, see the reference for the method of calculation. |
| 1.3.6.1.4.1.2696.3.2.1.9.10 | TablelinearityTable | not-accessible | current | Linearity characterization (shoulder attenuation) |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1 | RowlinearityEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.1 | ColumnlinearityInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.2 | ColumnlinearityTestState | read-only | current | This indicates whether the linearityValue is above the minimum permitted. |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.3 | ColumnlinearityEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.4 | ColumnlinearityCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.5 | ColumnlinearityCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.6 | ColumnlinearityCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.7 | ColumnlinearityLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.8 | ColumnlinearityActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.9 | ColumnlinearityMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.10.1.10 | ColumnlinearityValue | read-only | current | The current linearity (shoulder attenuation) expressed in dB. |
| 1.3.6.1.4.1.2696.3.2.1.9.15 | NodeberViterbiT | |||
| 1.3.6.1.4.1.2696.3.2.1.9.15.1 | TableberViterbiTTable | not-accessible | current | BER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transm… |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1 | RowberViterbiTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.1 | ColumnberViterbiTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.2 | ColumnberViterbiTTestState | read-only | current | This indicates whether the berViterbiTValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.3 | ColumnberViterbiTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.4 | ColumnberViterbiTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.5 | ColumnberViterbiTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.6 | ColumnberViterbiTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.7 | ColumnberViterbiTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.8 | ColumnberViterbiTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.9 | ColumnberViterbiTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.10 | ColumnberViterbiTValue | read-only | current | This is the overall pre-Viterbi BER value, for example 0.0000046 |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2 | TableberViterbiTLPTable | not-accessible | current | BER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmi… |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1 | RowberViterbiTLPEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.1 | ColumnberViterbiTLPInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.2 | ColumnberViterbiTLPTestState | read-only | current | This indicates whether the berViterbiTLPValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.3 | ColumnberViterbiTLPEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.4 | ColumnberViterbiTLPCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.5 | ColumnberViterbiTLPCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.6 | ColumnberViterbiTLPCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.7 | ColumnberViterbiTLPLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.8 | ColumnberViterbiTLPActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.9 | ColumnberViterbiTLPMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.10 | ColumnberViterbiTLPValue | read-only | current | This is the overall pre-Viterbi BER value, for example 0.0000046 |
| 1.3.6.1.4.1.2696.3.2.1.9.16 | NodeberRS | |||
| 1.3.6.1.4.1.2696.3.2.1.9.16.1 | TableberRSTable | not-accessible | current | BER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmissio… |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1 | RowberRSEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.1 | ColumnberRSInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.2 | ColumnberRSTestState | read-only | current | This indicates whether berRSValue is below the maximum. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.3 | ColumnberRSEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.4 | ColumnberRSCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.5 | ColumnberRSCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.6 | ColumnberRSCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.7 | ColumnberRSLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.8 | ColumnberRSActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.9 | ColumnberRSMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.10 | ColumnberRSValue | read-only | current | This is the BER before RS (outer) decoder measured using the in-service method. It is expressed as a number, e.g. 0.0000034 |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2 | TableberRSLPTable | not-accessible | current | BER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission… |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1 | RowberRSLPEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.1 | ColumnberRSLPInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.2 | ColumnberRSLPTestState | read-only | current | This indicates whether berRSLPValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.3 | ColumnberRSLPEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.4 | ColumnberRSLPCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.5 | ColumnberRSLPCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.6 | ColumnberRSLPCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.7 | ColumnberRSLPLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.8 | ColumnberRSLPActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.9 | ColumnberRSLPMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.10 | ColumnberRSLPValue | read-only | current | This is the BER before RS (outer) decoder for the low priority stream measured using the in-service method. It is expressed as a number, e.g. 0.0000034 |
| 1.3.6.1.4.1.2696.3.2.1.9.18 | NodeiqAnalysisT | |||
| 1.3.6.1.4.1.2696.3.2.1.9.18.2 | TablemerTTable | not-accessible | current | Modulation Error Ratio (MER) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1 | RowmerTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.1 | ColumnmerTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.2 | ColumnmerTTestState | read-only | current | This indicates whether merTValue is within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.3 | ColumnmerTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.4 | ColumnmerTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.5 | ColumnmerTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the merTCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.6 | ColumnmerTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.7 | ColumnmerTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.8 | ColumnmerTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.9 | ColumnmerTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.10 | ColumnmerTValue | read-only | current | The current Modulation Error Ratio expressed in dB |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3 | NodesteT | |||
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1 | TablesteMeanTTable | not-accessible | current | System Target Error Mean (STEM) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1 | RowsteMeanTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.1 | ColumnsteMeanTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.2 | ColumnsteMeanTTestState | read-only | current | This indicates whether steMeanTValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.3 | ColumnsteMeanTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.4 | ColumnsteMeanTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.5 | ColumnsteMeanTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.6 | ColumnsteMeanTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.7 | ColumnsteMeanTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.8 | ColumnsteMeanTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.9 | ColumnsteMeanTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.10 | ColumnsteMeanTValue | read-only | current | The current System Target Error Mean as a numeric value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2 | TablesteDeviationTTable | not-accessible | current | System Target Error Deviation (STED) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1 | RowsteDeviationTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.1 | ColumnsteDeviationTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.2 | ColumnsteDeviationTTestState | read-only | current | This indicates whether steDeviationTValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.3 | ColumnsteDeviationTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.4 | ColumnsteDeviationTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.5 | ColumnsteDeviationTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.6 | ColumnsteDeviationTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.7 | ColumnsteDeviationTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.8 | ColumnsteDeviationTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.9 | ColumnsteDeviationTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.10 | ColumnsteDeviationTValue | read-only | current | The current System Target Error Deviation as a numeric value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4 | TablecsTTable | not-accessible | current | Carrier Suppression (CS) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1 | RowcsTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.1 | ColumncsTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.2 | ColumncsTTestState | read-only | current | This indicates whether csTValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.3 | ColumncsTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.4 | ColumncsTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.5 | ColumncsTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.6 | ColumncsTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.7 | ColumncsTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.8 | ColumncsTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.9 | ColumncsTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.10 | ColumncsTValue | read-only | current | The current Carrier Suppression value in dB. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5 | TableaiTTable | not-accessible | current | Amplitude Imbalance (AI) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1 | RowaiTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.1 | ColumnaiTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.2 | ColumnaiTTestState | read-only | current | This indicates whether aiTValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.3 | ColumnaiTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.4 | ColumnaiTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.5 | ColumnaiTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.6 | ColumnaiTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.7 | ColumnaiTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.8 | ColumnaiTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.9 | ColumnaiTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.10 | ColumnaiTValue | read-only | current | The current Amplitude Imbalance as a percentage |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6 | TableqeTTable | not-accessible | current | Quadrature Error (QE) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1 | RowqeTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.1 | ColumnqeTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.2 | ColumnqeTTestState | read-only | current | This indicates whether qeTValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.3 | ColumnqeTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.4 | ColumnqeTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.5 | ColumnqeTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.6 | ColumnqeTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.7 | ColumnqeTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.8 | ColumnqeTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.9 | ColumnqeTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.10 | ColumnqeTValue | read-only | current | The current Quadrature Error value in degrees. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7 | TablepjTTable | not-accessible | current | Phase Jitter (PJ) measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1 | RowpjTEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.1 | ColumnpjTInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.2 | ColumnpjTTestState | read-only | current | This indicates whether pjTValue is currently within the thresholds. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.3 | ColumnpjTEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.4 | ColumnpjTCounter | read-only | current | Count of the number of times a threshold error has occurred for this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.5 | ColumnpjTCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.6 | ColumnpjTCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.7 | ColumnpjTLatestError | read-only | current | The timestamp at the most recent occurrence of a threshold error on this measurement. |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.8 | ColumnpjTActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.9 | ColumnpjTMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.10 | ColumnpjTValue | read-only | current | The current Phase Jitter value in degrees. |
| 1.3.6.1.4.1.2696.3.2.1.9.20 | TablemipSyntaxTable | not-accessible | current | SFN MIP baseband tests |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1 | RowmipSyntaxEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.1 | ColumnmipSyntaxInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.2 | ColumnmipSyntaxTestNumber | not-accessible | current | The specific SFN MIP test that this row applies to |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.3 | ColumnmipSyntaxState | read-only | current | This gives the overall pass/fail state of the test. |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.4 | ColumnmipSyntaxEnable | read-write | current | Determines whether this test and the associated trap are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.5 | ColumnmipSyntaxCounter | read-only | current | Count of the number of times this error has occurred |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.6 | ColumnmipSyntaxCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the mipSyntaxCounter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.7 | ColumnmipSyntaxCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.8 | ColumnmipSyntaxLatestError | read-only | current | The timestamp at the most recent occurrence of the error |
| 1.3.6.1.4.1.2696.3.2.1.9.20.1.9 | ColumnmipSyntaxActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.21 | NodesystemErrorPerformance | |||
| 1.3.6.1.4.1.2696.3.2.1.9.21.1 | TablesepEtiTable | not-accessible | current | Measurement of Errored Second Ratio (ESR) or Errored Time Interval Ratio (ETIR). |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1 | RowsepEtiEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.1 | ColumnsepEtiInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.2 | ColumnsepEtiTestState | read-only | current | A 'fail' indicaties that the most recently completed time interval TI was an Errored Time Interval (ETI). A 'pass' indicates that the most recent TI was not er… |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.3 | ColumnsepEtiEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.4 | ColumnsepEtiCounter | read-only | current | Count of the number of times an ETI has occurred. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.5 | ColumnsepEtiCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.6 | ColumnsepEtiCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.7 | ColumnsepEtiLatestError | read-only | current | The timestamp at the most recent occurrence of an ETI. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.8 | ColumnsepEtiActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.9 | ColumnsepEtiMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.10 | ColumnsepEtiValue | read-only | current | This is the Errored Time Interval Ratio (ETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2 | TablesepSetiTable | not-accessible | current | Measurement of Severly Errored Second Ratio (SESR) or Severely Errored Time Interval Ratio (SETIR). |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1 | RowsepSetiEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.1 | ColumnsepSetiInputNumber | not-accessible | current | Transport Stream on which the measurement is made |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.2 | ColumnsepSetiTestState | read-only | current | A 'fail' indicaties that the most recently completed time interval TI was a Severely Errored Time Interval (SETI). A 'pass' indicates that the most recent TI w… |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.3 | ColumnsepSetiEnable | read-write | current | Determines whether the threshold test and associated traps for this measurement are enabled. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.4 | ColumnsepSetiCounter | read-only | current | Count of the number of times an SETI has occurred. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.5 | ColumnsepSetiCounterDiscontinuity | read-only | current | Provides the last time at which there was a discontinuity in the counter object. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.6 | ColumnsepSetiCounterReset | read-write | current | The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value o… |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.7 | ColumnsepSetiLatestError | read-only | current | The timestamp at the most recent occurrence of a SETI. |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.8 | ColumnsepSetiActiveTime | read-only | current | The total time when it has been possible to perform this measurement |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.9 | ColumnsepSetiMeasurementState | read-only | current | Specifies the validity of the measurement value |
| 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.10 | ColumnsepSetiValue | read-only | current | This is the Severely Errored Time Interval Ratio (SETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value. |
| 1.3.6.1.4.1.2696.3.2.1.9.100 | TableterrestrialPreferencesTable | not-accessible | current | Table of terrestrial specific measurement preferences. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1 | RowterrestrialPreferencesEntry | not-accessible | current | Row specification |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.1 | ColumnterrestrialPrefInputNumber | not-accessible | current | Transport Stream input to which the preferences apply |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.2 | ColumnterrestrialPrefCentreFrequency | read-write | current | This is the centre frequency to which the measuring equipment is tuned for making terrestrial measurements. This frequency is the actual input frequency to the… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.3 | ColumnterrestrialPrefBandwidth | read-write | current | The instrument is set to expect a DVB-T transmission adapted for this bandwidth. Normal values will be 6.0MHz, 7.0MHz or 8.0MHz. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.4 | ColumnterrestrialPrefModulation | read-write | current | This is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to terrestrial measurement… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.5 | ColumnterrestrialPrefTransmissionMode | read-write | current | The instrument is set to expect a transmission in either 2k mode or 8k mode as set by this object. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.6 | ColumnterrestrialPrefGuardInterval | read-write | current | The instrument is set to expect a transmission using the guard interval specified by this object. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.7 | ColumnterrestrialPrefHierarchical | read-write | current | The instrument is set according to the value of this object to expect a transmission which is either non-hierachical or hierarchical using the specified alpha … |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.8 | ColumnterrestrialPrefCentreFreqExpected | read-write | current | This is the expected value for the centre frequency as measured by rfAccuracyValue. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.9 | ColumnterrestrialPrefCentreFreqLimit | read-write | current | This is the permitted deviation for the centre frequency as measured by rfAccuracyValue. If rfAccuracyValue is outside the range: [terrestrialPrefCentreFreqExp… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.10 | ColumnterrestrialPrefChannelWidthLimit | read-write | current | This is the permitted deviation for the channel width as measured by rfChannelWidthValue. The nominal value of the channel width has a fixed value which depend… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.11 | ColumnterrestrialPrefSymbolLengthLimit | read-write | current | This is the permitted deviation for the symbol length as measured by symbolLengthValue. The nominal value of the symbol length has a fixed value which depends … |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.12 | ColumnterrestrialPrefPowerMin | read-write | current | If the power measured by rfIfPowerValue is less than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.13 | ColumnterrestrialPrefPowerMax | read-write | current | If the power measured by rfIfPowerValue is greater than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.14 | ColumnterrestrialPrefENDBER | read-write | current | BER value which is to be used for the END and ENF measurements. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.15 | ColumnterrestrialPrefENDIdeal | read-write | current | This is the 'ideal' value of C/N for measurement of END on the whole or high priority stream. It is used in the measurement of eNDTValue. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.16 | ColumnterrestrialPrefENDMax | read-write | current | If the measured value of eNDTValue exceeds this, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.17 | ColumnterrestrialPrefENFIdeal | read-write | current | This is the 'ideal' value of C/N for measurement of ENF on the whole or high priority stream. It is used in the measurement of eNFTValue. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.18 | ColumnterrestrialPrefENFMax | read-write | current | If the measured value of eNFTValue is exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.19 | ColumnterrestrialPrefENDLPIdeal | read-write | current | This is the 'ideal' value of C/N for measurement of END on the low priority stream. It is used in the measurement of eNDTLPValue. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.20 | ColumnterrestrialPrefENDLPMax | read-write | current | If the measured value of eNDTLPValue exceeds this, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.21 | ColumnterrestrialPrefENFLPIdeal | read-write | current | This is the 'ideal' value of C/N for measurement of ENF on the low priority stream. It is used in the measurement of eNFTLPValue. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.22 | ColumnterrestrialPrefENFLPMax | read-write | current | If the measured value of eNFTLPValue exeeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.23 | ColumnterrestrialPrefLinearityMin | read-write | current | If the shoulder attenuation as measured by linearityValue is less than this value, an error is indicated. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.24 | ColumnterrestrialPrefBERViterbiMax | read-write | current | If the BER measured by berViterbiTValue exceeds this value, an error is indicated. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.25 | ColumnterrestrialPrefBERViterbiLPMax | read-write | current | If the BER measured by berViterbiTLPValue exceeds this value, an error is indicated. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.26 | ColumnterrestrialPrefBERRSMax | read-write | current | If the BER measured by berRSValue exceeds this value, an error is indicated. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.27 | ColumnterrestrialPrefBERRSLPMax | read-write | current | If the BER measured by berRSLPValue exceeds this value, an error is indicated. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.28 | ColumnterrestrialPrefMerTMin | read-write | current | If merTValue is less than this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.29 | ColumnterrestrialPrefSteMeanMax | read-write | current | If steMeanTValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.30 | ColumnterrestrialPrefSteDeviationMax | read-write | current | If steDeviationTValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.31 | ColumnterrestrialPrefCsMin | read-write | current | If csTValue is less than this value, the associated test fails |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.32 | ColumnterrestrialPrefAiMax | read-write | current | If aiTValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.33 | ColumnterrestrialPrefQeMax | read-write | current | If qeTValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.34 | ColumnterrestrialPrefPjMax | read-write | current | If pjTValue exceeds this value, the associated test fails. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.35 | ColumnterrestrialPrefMIPTimingLimit | read-write | current | This preference affects the MIP_timing_error test. If the calculated value of nT differs from an integral number of seconds by more than terrestrialPrefMIPTimi… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.36 | ColumnterrestrialPrefMIPDeviationMax | read-write | current | This preference affects the MIP_ts_rate_error test. It is the value of Max_deviation in the inequality given in TR 101 290 as the condition for an error indica… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.37 | ColumnterrestrialPrefSEPUATMode | read-write | current | Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' … |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.38 | ColumnterrestrialPrefSEPN | read-write | current | The N value used to identify the start and end of a period of unavailable time (UAT). |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.39 | ColumnterrestrialPrefSEPT | read-write | current | The T value used to identify the start and end of a period of unavailable time (UAT). |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.40 | ColumnterrestrialPrefSEPM | read-write | current | The M value used to identify the start and end of a period of unavailable time (UAT). |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.41 | ColumnterrestrialPrefSEPTI | read-write | current | Each Time Interval of this length is assessed as to whether it is an Errored Time Interval or a Severely Errored Time Interval. |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.42 | ColumnterrestrialPrefSEPEBPerCent | read-write | current | If more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values… |
| 1.3.6.1.4.1.2696.3.2.1.9.100.1.43 | ColumnterrestrialPrefSEPMeasurementInterval | read-write | current | The Measurement Interval (MI) over which the ESR/ETIR and SESR/SETIR are calculated. |
| 1.3.6.1.4.1.2696.3.2.3 | Nodetr101290Conformance | |||
| 1.3.6.1.4.1.2696.3.2.3.1 | Nodetr101290Compliances | |||
| 1.3.6.1.4.1.2696.3.2.3.1.1 | CompliancecomplianceTransportStream | current | Compliance for Transport Stream monitor devices | |
| 1.3.6.1.4.1.2696.3.2.3.1.2 | CompliancecomplianceCable | current | Compliance for Cable RF measurement devices | |
| 1.3.6.1.4.1.2696.3.2.3.1.3 | CompliancecomplianceSatellite | current | Compliance for Satellite RF measurement devices | |
| 1.3.6.1.4.1.2696.3.2.3.1.4 | CompliancecomplianceTerrestrial | current | Compliance for Terrestrial RF measurement devices | |
| 1.3.6.1.4.1.2696.3.2.3.2 | Nodetr101290ObjectGroups | |||
| 1.3.6.1.4.1.2696.3.2.3.2.1 | GroupgroupControl | current | Contains all the objects from the tr101290Control branch of the MIB | |
| 1.3.6.1.4.1.2696.3.2.3.2.2 | GroupgroupTrapControl | current | Contains all the normal objects from the tr101290Trap branch of the MIB | |
| 1.3.6.1.4.1.2696.3.2.3.2.3 | GroupgroupTraps | current | Contains all the traps/notifications from the MIB. | |
| 1.3.6.1.4.1.2696.3.2.3.2.4 | GroupgroupCapability | current | Contains all objects from the tr101290Capability branch of the MIB | |
| 1.3.6.1.4.1.2696.3.2.3.2.5 | GroupgroupTransportStream | current | Contains all objects relevant to Transport Stream measurement | |
| 1.3.6.1.4.1.2696.3.2.3.2.6 | GroupgroupCable | current | Contains all objects relevant to cable RF measurement | |
| 1.3.6.1.4.1.2696.3.2.3.2.7 | GroupgroupSatellite | current | Contains all objects relevent to satellite RF measurements | |
| 1.3.6.1.4.1.2696.3.2.3.2.8 | GroupgroupTerrestrial | current | Contains all objects relevant to terrestrial RF measurements |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ActiveTime | Unsigned32 | current | This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform a particular test or measurement. The instrument might not be perfo… |
| Availability | INTEGER { notAvailable(1), testAvailable(2), measurementAvailable(3), measurementAndTestAvailable(4) } | current | Availability is used in the capabilities branch of the MIB to indicate whether the instrument is equipped to provide a specific test and/or measurement. |
| BERMeasurementMethod | INTEGER { iqSeparate(1), iqCombined(2) } | current | Indicates the method used for measuring BER before Viterbi decoding |
| BitRateElement | INTEGER { bit(1), byte(2), packet(3), other(4) } | current | The fundamental data unit that is being counted by the bit rate measurement algorithm. |
| DeliverySystemType | INTEGER { unknown(1), cable(2), satellite(3), terrestrial(4) } | current | Specifies the physical delivery system used for a Transport Stream. |
| Enable | BITS { testEnable(0), failTrapEnable(1), unknownTrapEnable(2) } | current | This type is used for the '...Enable' objects of tests and measurements. It determines whether the test is enabled and also which traps can be generated by this test/measurement. If the testEnable bit is zero, the test … |
| FloatingPoint | OCTET STRING (SIZE (1..63)) | current | FloatingPoint provides a way of representing non-integer numbers in SNMP. Numbers are represented as a string of ASCII characters in the natural way. So for example, '3', '3.142' and '0.3142E1' are all valid numbers. Th… |
| GroupAvailability | INTEGER { noSupport(1), selectiveSupport(2), completeSupport(3) } | current | This is used in the tr101290Capability branch of the MIB to specify an agent's degree of support for a whole branch of the MIB. The individual values mean: noSupport no objects in this branch are available selectiveSupp… |
| GuardInterval | INTEGER { interval1d4(1), interval1d8(2), interval1d16(3), interval1d32(4) } | current | Guard intervals as specified for DVB-T transmissions. interval1d4 means a guard interval of 1/4. |
| Hierarchy | INTEGER { nonHierarchical(1), hierarchicalAlphaOne(2), hierarchicalAphaTwo(3), hierarchicalAlphaFour(4) } | current | In DVB-T systems this is used to specify whether the transmission is hierarchical, and if so, the value of alpha. |
| IndexConsistencyTest | INTEGER { tsIdCheck(1) } | current | Index of consistency check tests |
| IndexMIPSyntaxTest | INTEGER { mipTimingError(1), mipStructureError(2), mipPresenceError(3), mipPointerError(4), mipPeriodicityError(5), mipTsRateError(6) } | current | This assigns numbers to the MIP syntax tests. These numbers are then used as indexes into the MIP syntax table. |
| IndexPCRMeasurement | INTEGER { pcrFO(1), pcrDR(2), pcrOJ(3), pcrAC(4) } | current | This assigns numbers to the PCR measurements. These numbers are then used as indexes into the PCR measurement table. |
| IndexServicePerformance | INTEGER { serviceAvailability(1), serviceDegradation(2), serviceImpairments(3) } | current | This assigns numbers to the Service Performance measurements. These numbers are then used as indexes into the Service Performance measurement table. |
| IndexTransportStreamTest | INTEGER { tsSyncLoss(1010), syncByteError(1020), patError2(1031), continuityCountError(1040), pmtError2(1051), pidError(1060), transportError(2010), crcError(2020), pcrRepetitionError(2031), pcrDiscontinuityError(2032), pcrAccuracyError(2040), ptsError(2050), catError(2060), nitActualError(3011), nitOtherError(3012), siRepetitionError(3020), bufferError(3030), unreferencedPID(3041), sdtActualError(3051), sdtOtherError(3052), eitActualError(3061), eitOtherError(3062), eitPfError(3063), rstError(3070), tdtError(3080), emptyBufferError(3090), dataDelayError(3100) } | current | IndexTransportStreamTest assigns a unique numerical value to each of the TR 101 290 Transport Stream tests in section 5.2. The number allocated is: priority * 1000 + test number * 10 + subtest Subtest is zero if there i… |
| InputNumber | INTEGER (1..2147483647) | current | InputNumber objects are used to select a specific Transport Stream input on a multi-input monitoring/measurement device. On a single input monitoring/measuring device, InputNumber objects will always have the value one. |
| MeasurementState | INTEGER { disabled(1), unknown(2), normal(3), abnormal(4) } | current | MeasurementState is used to represent the state of a single measurement. 'disabled' means that the measurement has been disabled by setting the 'testEnable' bit in its ...Enable object to zero. 'unknown' means that the … |
| Modulation | INTEGER { bpsk(1), qpsk(2), psk8(3), qam16(4), qam32(5), qam64(6), qam128(7), qam256(8), qam16Alpha2(9), qam64Alpha2(10), qam16Alpha4(11), qam64Alpha4(12) } | current | Modulation systems used in RF transmissions |
| PIDPlusOne | INTEGER (1..8192) | current | An object of type PIDPlusOne represents an MPEG-2 PID number. The numeric value of the object is the PID + 1, to allow for its use as a table index. |
| PollingInterval | Integer32 | current | Objects of this type are used by the agent to indicate how often it internally updates the information related to a particular test or measurement. The manager can then adjust its polling behaviour accordingly. The poll… |
| RateStatus | INTEGER { disabled(1), enabled(2), enabledThrottled(3) } | current | RateStatus is used in trap control |
| ServiceId | INTEGER (1..65535) | current | Allowed values of program_number/service_id. Note that zero is used in the PAT to represent the NIT PID and so will never occur as a service_id. |
| TerrestrialTransmissionMode | INTEGER { mode2k(1), mode8k(2) } | current | Transmission mode for DVB-T transmissions, specifies whether there are 2k or 8k carriers. |
| TestState | INTEGER { disabled(1), unknown(2), pass(3), fail(4) } | current | TestState is used to represent the state of a single test. 'disabled' means that the test has been disabled by setting the 'testEnable' bit of its ...Enable variable to zero. 'unknown' means that the equipment cannot pr… |
| TestSummary | BITS { tsTsSyncLoss(0), tsSyncByteError(1), tsPatError2(2), tsContinuityCountError(3), tsPmtError2(4), tsPidError(5), tsTransportError(6), tsCrcError(7), tsPcrRepetitionError(8), tsPcrDiscontinuityError(9), tsPcrAccuracyError(10), tsPtsError(11), tsCatError(12), tsNitActualError(13), tsNitOtherError(14), tsSiRepetitionError(15), tsBufferError(16), tsUnreferencedPID(17), tsSdtActualError(18), tsSdtOtherError(19), tsEitActualError(20), tsEitOtherError(21), tsEitPfError(22), tsRstError(23), tsTdtError(24), tsEmptyBufferError(25), tsDataDelayError(26), pcrPcrFO(27), pcrPcrDR(28), pcrPcrOJ(29), pcrPcrAC(30), bitrateTransportStream(31), bitrateService(32), bitratePID(33), tsTsConsistency(34), performanceServiceAvailability(35), performanceServiceDegradation(36), performanceServiceImpairments(37), csSysAvailability(38), csLinkAvailability(39), csBerRS(40), csRFIFSignalPower(41), csNoisePower(42), csMer(43), csSteMean(44), csSteDeviation(45), csCS(46), csAI(47), csQE(48), csRTE(49), csCI(50), csPJ(51), csSNR(52), cNoiseMargin(53), cEstNoiseMargin(54), cSignQualMarT(55), cEND(56), cOutBandEmiss(57), sBerViterbi(58), sIfSpectrum(59), tRFAccuracy(60), tRFChannelWidth(61), tSymbolLength(62), tRFIFPower(63), tRFIFSpectrum(64), tEND(65), tENF(66), tENDLP(67), tENFLP(68), tLinearity(69), tBerViterbi(70), tBerViterbiLP(71), tBerRS(72), tBerRSLP(73), tMER(74), tSteMean(75), tSteDeviation(76), tCS(77), tAI(78), tQE(79), tPJ(80), tMipTimingError(81), tMipStructureError(82), tMipPresenceError(83), tMipPointerError(84), tMipPeriodicityError(85), tMipTsRateError(86), tSepEti(87), tSepSeti(88) } | current | Bit String providing a status summary for all the tests defined in this MIB module. A bit is set to one if the state of that test is 'fail'. In several cases, a single bit summarises the results of a set of tests. In th… |
| TransportStreamID | INTEGER (0..65535) | current | Range of possible values for a transport_stream_id as found in the PAT. |
| UATMode | INTEGER { nConsecutive(1), rollingWindow(2) } | current | Method of determining the start and end of a period of Unavailable Time. |