EDGELINK-MIB
102 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress NetworkAddress ObjectName ObjectSyntax TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.564 | Nodetelco | |||
| 1.3.6.1.4.1.564.101 | NodeedgeLink | |||
| 1.3.6.1.4.1.564.101.1 | NodeelM13v1 | |||
| 1.3.6.1.4.1.564.101.1.1 | NodeedgeLinkEvent | This trap is sent when an alarm event is set or cleard. | ||
| 1.3.6.1.4.1.564.101.1.1 | NodeelDS1CM | |||
| 1.3.6.1.4.1.564.101.1.1.1 | TableelDS1CMTable | not-accessible | mandatory | DS1 Configuration Management table. |
| 1.3.6.1.4.1.564.101.1.1.1.1 | RowelDS1CMEntry | not-accessible | mandatory | DS1 Configuration Management table entry. |
| 1.3.6.1.4.1.564.101.1.1.1.1.1 | ColumnelDS1CMChannelNumber | read-only | mandatory | Table index, the DS1 channel number. |
| 1.3.6.1.4.1.564.101.1.1.1.1.2 | ColumnelDS1CMLineCode | read-write | mandatory | Select DS1 line code for the channel number selected by this tables index. |
| 1.3.6.1.4.1.564.101.1.1.1.1.3 | ColumnelDS1CMLineBuildout | read-write | mandatory | Select line build-out for the DS1 line selected by this tables index:, 0 to 133 ft, or 133 to 266 ft, 266 to 399 ft, 399 to 533 ft, or 533 to 655 ft. |
| 1.3.6.1.4.1.564.101.1.1.1.1.4 | ColumnelDS1CMLoopbackMode | read-write | mandatory | Set the DS1 loopback mode to Line, terminal, remote, or none. In M13 Mode, issuing a DS1 Remote Terminal Lpbk will cause any previous Remote DS1 Terminal Lpbk(… |
| 1.3.6.1.4.1.564.101.1.1.1.1.5 | ColumnelDS1CMServiceMode | read-write | mandatory | Set the DS1 service mode for the channel indicated to in-service or out-of-service. Certain service effecting operations can not be initiated unless the DS1 ch… |
| 1.3.6.1.4.1.564.101.1.1.1.1.6 | ColumnelDS1CMInterfaceEquipped | read-write | mandatory | DS1 Interfaces may be 'equipped' or 'unequipped'. No PM or FM operations will occur on an unequipped interface. Access is allowed to MIB variables which corres… |
| 1.3.6.1.4.1.564.101.1.1.1.1.7 | ColumnelDS1CMChannelName | read-write | mandatory | A ChannelName can be assigned for each DS1 channel. The Channel name cannot be more than 10 characters. |
| 1.3.6.1.4.1.564.101.1.1.1.1.8 | ColumnelDS1CMInputStatus | read-only | mandatory | Reports the input State of the DS1 channel indexed by Channel Number. |
| 1.3.6.1.4.1.564.101.1.1.1.1.9 | ColumnelDS1CMMaskState | read-only | mandatory | Get the state of the DS1 Channel identified by the index. The Mask state identifies the Autosense State of the DS1 Channel. |
| 1.3.6.1.4.1.564.101.1.1.1.1.10 | ColumnelDS1CMInterfaceRescan | read-write | mandatory | Rescan the DS1 Channel identified by the index. |
| 1.3.6.1.4.1.564.101.1.1.2 | ScalarelALLDS1CMLineCode | read-write | mandatory | Set DS1 line code for all DS1 channels. A value Inderminate(3) will be returned if All the DS1 Channels are not set to either ds1LineCodeAMI or ds1LineCodeB8ZS. |
| 1.3.6.1.4.1.564.101.1.1.3 | ScalarelALLDS1CMLineBuildout | read-write | mandatory | Select line build-out for All the DS1 lines to 0 to 133 ft, or 133 to 266 ft, 266 to 399 ft, 399 to 533 ft, or 533 to 655 ft. |
| 1.3.6.1.4.1.564.101.1.1.4 | ScalarelALLDS1CMLoopbackMode | read-write | mandatory | Set the DS1 loopback mode to Line, Terminal, Remote, or None for All the DS1 Channels. In M13 Mode, issuing a DS1 Remote Terminal Lpbk will cause any previous … |
| 1.3.6.1.4.1.564.101.1.1.5 | ScalarelALLDS1CMServiceMode | read-write | mandatory | Set the DS1 service mode for All DS1 channels to in-service or out-of-service. Certain service effecting operations can not be initiated unless All the DS1 cha… |
| 1.3.6.1.4.1.564.101.1.1.6 | ScalarelALLDS1CMInterfaceEquipped | read-write | mandatory | Set All the DS1 Channels to 'equipped' or 'unequipped' state. No PM or FM operations will occur on an unequipped DS1 interface. Access is allowed to MIB variab… |
| 1.3.6.1.4.1.564.101.1.2 | NodeelCM | |||
| 1.3.6.1.4.1.564.101.1.2.1 | ScalarelCMSystemStatus | read-only | mandatory | This DisplayString gives the summary information about the Current EdgeLink100 System Status. The Description includes ... 1) chasisType 2) Active Module 3) Fa… |
| 1.3.6.1.4.1.564.101.1.2.2 | ScalarelCMDS3ParityMode | read-write | mandatory | Select C-bit or P-bit parity mode for DS3 interface. This Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.3 | ScalarelCMDS3LineBuildout | read-write | mandatory | Select line build-out for DS3 Line, 0 to 100 ft, 100 to 200 ft, or 200-450.This MIB Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.4 | ScalarelCMDS3TxTiming | read-write | mandatory | Select mode for DS3 transmit timing. This MIB Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.5 | ScalarelCMProtectionMode | read-write | mandatory | In unprotected mode, switching is prohibited. While in protected mode, a standing minor alarm will occur if the off-line card is unavailable or not in operatio… |
| 1.3.6.1.4.1.564.101.1.2.6 | ScalarelCMCardSelect | read-write | mandatory | Read or select choice of on-line card. This operation will force a switch to occur if the off-line card is selected. |
| 1.3.6.1.4.1.564.101.1.2.7 | ScalarelCMClearTooManySwitches | read-write | mandatory | Clear switching-disabled state which occurs as a result of too many switches between the cards in a protected system in a 10 minute interval. ClearTooManySwitc… |
| 1.3.6.1.4.1.564.101.1.2.8 | ScalarelCMDS3LoopbackMode | read-write | mandatory | Set the DS3 loopback mode to line, terminal, remote, or none. The System can't be set to ds3LpbkRemoteFacility when it is in M13 Mode. The Terminal LoopBack is… |
| 1.3.6.1.4.1.564.101.1.2.9 | ScalarelCMDS3ServiceMode | read-write | mandatory | Set the DS3 service mode to in-service or out-of-service. Certain service effecting operations can not be initiated unless the DS3 channel is placed out-of-ser… |
| 1.3.6.1.4.1.564.101.1.2.10 | ScalarelCMCurTimeDate | read-write | mandatory | Read or set the system real time clock. The string is in the form MM/DD/YYYY HH:MM:SS. |
| 1.3.6.1.4.1.564.101.1.2.11 | ScalarelCMBerThreshold | read-write | mandatory | Set the BER Threshold value for the system to 10-6, 10-7, 10-8 or 10-9. BerThershold can't changed when the ServiceMode is IN-Service. |
| 1.3.6.1.4.1.564.101.1.2.12 | ScalarelCMSystemInfo | read-only | mandatory | Gets information about the MPU type, board revision, card revision level, software revision, CLEI code, MAC address, and Date of manufacture. |
| 1.3.6.1.4.1.564.101.1.2.13 | ScalarelCMPPPPortBaudRate | read-only | mandatory | Specifies the baud rate on the craft/PPP port when that port is running PPP (i.e. when carrier detect is asserted). |
| 1.3.6.1.4.1.564.101.1.3 | NodeelCMIfc | |||
| 1.3.6.1.4.1.564.101.1.3.1 | ScalarelCMRemoteCBitIPAddress | read-write | mandatory | This is the IP address of the partner EdgeLink's C-bit channel interface. This is used for partner-to-partner communications. Must be on same subnet as elCMLoc… |
| 1.3.6.1.4.1.564.101.1.3.2 | ScalarelCMLocalCBitIPAddress | read-write | mandatory | This is the IP address of my C-bit channel interface and is used for partner-to-partner communications. Must be on same subnet as elCMRemoteCBitIPAddress. This… |
| 1.3.6.1.4.1.564.101.1.3.3 | ScalarelCMCBitIPSubnetMask | read-write | mandatory | Specifies the subnet address mask for the C-Bit IP channel. |
| 1.3.6.1.4.1.564.101.1.3.4 | ScalarelCMRemotePPPIPAddress | read-write | mandatory | This is the IP Address for the Remote Client during PPP session. |
| 1.3.6.1.4.1.564.101.1.3.5 | TableelCMIfcTable | not-accessible | mandatory | Ethernet/PPP Interfaces table. |
| 1.3.6.1.4.1.564.101.1.3.5.1 | RowelCMIfcEntry | not-accessible | mandatory | Ethernet/PPP Interfaces table entry. |
| 1.3.6.1.4.1.564.101.1.3.5.1.1 | ColumnelCMIfcInterfaceNumber | read-only | mandatory | Table index. The table has one row for each external IP interface, Ethernet and PPP. |
| 1.3.6.1.4.1.564.101.1.3.5.1.2 | ColumnelCMIfcMyIPAddr | read-write | mandatory | The IP address for this interface. |
| 1.3.6.1.4.1.564.101.1.3.5.1.3 | ColumnelCMIfcMyIPSubnetAddrMask | read-write | mandatory | Subnet address mask for this IP address. |
| 1.3.6.1.4.1.564.101.1.3.5.1.4 | ColumnelCMIfcMyDefaultGatewayAddr | read-write | mandatory | Default gateway address for this interface. If 0, it will be ignored. |
| 1.3.6.1.4.1.564.101.1.3.5.1.5 | ColumnelCMIfcTrapSendAddr1 | read-write | mandatory | Address 1 of 4 to send traps to. If 0, will be ignored. |
| 1.3.6.1.4.1.564.101.1.3.5.1.6 | ColumnelCMIfcTrapSendAddr2 | read-write | mandatory | Address 2 of 4 to send traps to. If 0, will be ignored. |
| 1.3.6.1.4.1.564.101.1.3.5.1.7 | ColumnelCMIfcTrapSendAddr3 | read-write | mandatory | Address 3 of 4 to send traps to. If 0, will be ignored. |
| 1.3.6.1.4.1.564.101.1.3.5.1.8 | ColumnelCMIfcTrapSendAddr4 | read-write | mandatory | Address 4 of 4 to send traps to. If 0, will be ignored. |
| 1.3.6.1.4.1.564.101.1.4 | NodeelPM | |||
| 1.3.6.1.4.1.564.101.1.4.1 | ScalarelPMDS3TotalSwitches | read-only | mandatory | Number of switches which have occurred since startup, or since last time PM metrics were cleared. |
| 1.3.6.1.4.1.564.101.1.4.2 | ScalarelPMClearAllPMMetrics | read-write | mandatory | Clears all Performance Management related metrics and statistics. On a read, the value indeterminate(1) will be returned if this variable was never set to clea… |
| 1.3.6.1.4.1.564.101.1.5 | NodeelDS1PM | |||
| 1.3.6.1.4.1.564.101.1.5.1 | ScalarelDS1PMTimeElapsed | read-only | mandatory | The number of elapsed seconds in the current interval of DS1 PM data. |
| 1.3.6.1.4.1.564.101.1.5.2 | ScalarelDS1PMValidIntervals | read-only | mandatory | The number of intervals which have elapsed and for which PM data can read, up to and including 96. |
| 1.3.6.1.4.1.564.101.1.6 | NodeelDS1PMCur | |||
| 1.3.6.1.4.1.564.101.1.6.1 | TableelDS1PMCurTable | not-accessible | mandatory | DS1 current PM metrics table. |
| 1.3.6.1.4.1.564.101.1.6.1.1 | RowelDS1PMCurEntry | not-accessible | mandatory | DS1 current PM metrics table entry. |
| 1.3.6.1.4.1.564.101.1.6.1.1.1 | ColumnelDS1PMCurChannelNumber | read-only | mandatory | Table index. Rows are indexed by DS1 channel. |
| 1.3.6.1.4.1.564.101.1.6.1.1.2 | ColumnelDS1PMCurLineCodeViolations | read-only | mandatory | Number of line code violations in the current 15 minute interval. |
| 1.3.6.1.4.1.564.101.1.6.1.1.3 | ColumnelDS1PMCurErroredSeconds | read-only | mandatory | Number of errored seconds in the current interval. |
| 1.3.6.1.4.1.564.101.1.7 | NodeelDS1PMIvl | |||
| 1.3.6.1.4.1.564.101.1.7.1 | TableelDS1PMIvlTable | not-accessible | mandatory | DS1 Interval PM metrics table. |
| 1.3.6.1.4.1.564.101.1.7.1.1 | RowelDS1PMIvlEntry | not-accessible | mandatory | DS1 Interval PM metrics table entry. |
| 1.3.6.1.4.1.564.101.1.7.1.1.1 | ColumnelDS1PMIvlChannelNumber | read-only | mandatory | Primary table index, a DS1 channel number. |
| 1.3.6.1.4.1.564.101.1.7.1.1.2 | ColumnelDS1PMIvlIntervalNumber | read-only | mandatory | Secondary table index, the interval number. |
| 1.3.6.1.4.1.564.101.1.7.1.1.3 | ColumnelDS1PMIvlLineCodeViolations | read-only | mandatory | Number of line code violations for the channel specified by elDS1PMIvlChannelNumber and in the interval indicated by elDS1PMIvlIntervalNumber. |
| 1.3.6.1.4.1.564.101.1.7.1.1.4 | ColumnelDS1PMIvlErroredSeconds | read-only | mandatory | Number of errored seconds for the channel specified by elDS1PMIvlChannelNumber and in the interval indicated by elDS1PMIvlIntervalNumber. |
| 1.3.6.1.4.1.564.101.1.8 | NodeelDS1PMTot | |||
| 1.3.6.1.4.1.564.101.1.8.1 | TableelDS1PMTotTable | not-accessible | mandatory | DS1 Total PM metrics table. |
| 1.3.6.1.4.1.564.101.1.8.1.1 | RowelDS1PMTotEntry | not-accessible | mandatory | DS1 Total PM metrics table entry. |
| 1.3.6.1.4.1.564.101.1.8.1.1.1 | ColumnelDS1PMTotChannelNumber | read-only | mandatory | Table index, DS1 channel number. |
| 1.3.6.1.4.1.564.101.1.8.1.1.2 | ColumnelDS1PMTotLineCodeViolations | read-only | mandatory | Total number of line code violations for the channel specified by elDS1PMIvlChannelNumber. |
| 1.3.6.1.4.1.564.101.1.8.1.1.3 | ColumnelDS1PMTotErroredSeconds | read-only | mandatory | Total number of errored seconds for the channel specified by elDS1PMIvlChannelNumber. |
| 1.3.6.1.4.1.564.101.1.9 | NodeelFM | |||
| 1.3.6.1.4.1.564.101.1.9.1 | ScalarelFMFillAlarmLogTable | read-write | mandatory | Take a snapshot of the alarm log. Must be done before reading the log into the alarm log table, elFMAlmLogTable. On a read, the value indeterminate(1) will be … |
| 1.3.6.1.4.1.564.101.1.9.2 | ScalarelFMClearAlarmLog | read-write | mandatory | Clears the system's alarm log. On a read, the value indeterminate(1) will be returned if the SNMP variable was never set to clearAlarmLog(2) otherwise clearAla… |
| 1.3.6.1.4.1.564.101.1.9.3 | ScalarelFMDS1AutoSenseMode | read-write | mandatory | The AutoSense Mode will be enabled or Disabled on all the 28 Ds1 channels. The Rescan command will scan all the equipped DS1 Inputs and update their state. |
| 1.3.6.1.4.1.564.101.1.9.4 | ScalarelFMDS1InputAlarmMode | read-write | mandatory | This command changes the severity of the DS1 LOS as either Major alarm or status depending on the selection. |
| 1.3.6.1.4.1.564.101.1.10 | NodeelFMAlmLog | |||
| 1.3.6.1.4.1.564.101.1.10.1 | TableelFMAlmLogTable | not-accessible | mandatory | Alarm log table. This table holds a snapshot of the alarm log, and is filled by elFMFillAlarmLogTable. |
| 1.3.6.1.4.1.564.101.1.10.1.1 | RowelFMAlmLogEntry | not-accessible | mandatory | Alarm log table entry. |
| 1.3.6.1.4.1.564.101.1.10.1.1.1 | ColumnelFMAlmLogEntryNumber | read-only | mandatory | Table index, between 1 and 100. |
| 1.3.6.1.4.1.564.101.1.10.1.1.2 | ColumnelFMAlmLogTableAlarmNumber | read-only | mandatory | Alarm number. |
| 1.3.6.1.4.1.564.101.1.10.1.1.3 | ColumnelFMAlmLogTableDescription | read-only | mandatory | Alarm description. |
| 1.3.6.1.4.1.564.101.1.10.1.1.4 | ColumnelFMAlmLogTableStatus | read-only | mandatory | Alarm status. |
| 1.3.6.1.4.1.564.101.1.10.1.1.5 | ColumnelFMAlmLogTableTimestamp | read-only | mandatory | Alarm time stamp in the form mm/dd/yy hh:mm:ss. |
| 1.3.6.1.4.1.564.101.1.10.1.1.6 | ColumnelFMAlmLogTableChannel | read-only | mandatory | Channel associated with the alarm, if any. |
| 1.3.6.1.4.1.564.101.1.11 | NodeelFMCurAlm | |||
| 1.3.6.1.4.1.564.101.1.11.1 | TableelFMCurAlmTable | not-accessible | mandatory | Current alarms table. |
| 1.3.6.1.4.1.564.101.1.11.1.1 | RowelFMCurAlmEntry | not-accessible | mandatory | Current alarms table entry. |
| 1.3.6.1.4.1.564.101.1.11.1.1.1 | ColumnelFMCurAlmTableAlarmNumber | read-only | mandatory | Primary table index, an alarm number. |
| 1.3.6.1.4.1.564.101.1.11.1.1.2 | ColumnelFMCurAlmTableChannel | read-only | mandatory | Secondary table index. Channel associated with the alarm, can be 0 if channel number is irrelevant to the alarm. |
| 1.3.6.1.4.1.564.101.1.11.1.1.3 | ColumnelFMCurAlmTableDescription | read-only | mandatory | Alarm description. |
| 1.3.6.1.4.1.564.101.1.12 | NodeelFMTrapFields | |||
| 1.3.6.1.4.1.564.101.1.12.1 | ScalarelFMTrapAlarmNumber | read-only | mandatory | Alarm number associated with the last sent trap. |
| 1.3.6.1.4.1.564.101.1.12.2 | ScalarelFMTrapAlarmText | read-only | mandatory | Alarm text associated with the last sent trap. |
| 1.3.6.1.4.1.564.101.1.12.3 | ScalarelFMTrapTimeStamp | read-only | mandatory | Time stamp associated with the last sent trap. |
| 1.3.6.1.4.1.564.101.1.12.4 | ScalarelFMTrapAlarmStatus | read-only | mandatory | Alarm status associated with the last sent trap. |
| 1.3.6.1.4.1.564.101.1.12.5 | ScalarelFMTrapChannelNumber | read-only | mandatory | Channel number associated with the last sent trap, if any. |