ES1200-MIB
371 objects
No module-level DESCRIPTION found.
Imported Objects
| BRIDGE-MIB | dot1dBasePort MacAddress |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.326 | Nodefore | |||
| 1.3.6.1.4.1.326.2 | Nodesystems | |||
| 1.3.6.1.4.1.326.2.20 | Nodeethernet | |||
| 1.3.6.1.4.1.326.2.20.1 | Nodeedge | |||
| 1.3.6.1.4.1.326.2.20.1.1 | Nodeedgecommon | |||
| 1.3.6.1.4.1.326.2.20.1.2 | Nodegolf | |||
| 1.3.6.1.4.1.326.2.20.1.2.1 | Nodegolfproducts | |||
| 1.3.6.1.4.1.326.2.20.1.2.1.2 | Nodees1200 | |||
| 1.3.6.1.4.1.326.2.20.1.2.1.2.1 | NodeswEventPortPartition | The trap is sent whenever the port state enter the Partion mode when more than 61 collisions occur while trasmitting. | ||
| 1.3.6.1.4.1.326.2.20.1.2.1.2.2 | NodeswEventlinkChangeEvent | The trap is sent whenever the link state of a port changes from link up to link down or from link down to link up | ||
| 1.3.6.1.4.1.326.2.20.1.2.1.2.3 | NodeswEventBcastRisingStorm | The trap indicates that broadcast higher rising threshold . This trap including the port ID | ||
| 1.3.6.1.4.1.326.2.20.1.2.1.2.4 | NodeswEventBcastFallingStorm | The trap indicates that broadcast higher falling threshold . This trap including the port ID | ||
| 1.3.6.1.4.1.326.2.20.1.2.2 | Nodegolfcommon | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1 | Nodefore-products | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25 | Nodefore-es1200Prod | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.1 | NodeswProperty | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.1.1 | NodeswModule | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.2 | Nodees1200DevRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.2.1 | Nodees1200Device | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3 | Nodees1200UnitRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.1 | Nodees1200Master | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.2 | Nodees1210Slave1 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.3 | Nodees1210Slave2 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.4 | Nodees1210Slave3 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4 | Nodees1200ModuleRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.1 | Nodees1200ModuleMainboardTx | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.2 | Nodees1200ModuleTxTwoPort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.3 | Nodees1200ModuleFxSC | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.4 | Nodees1200ModuleFxMTRJ | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.5 | Nodees1200ModuleSIO | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.6 | Nodees1200ModuleSXGIGAOnePort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.7 | Nodees1200ModuleSXGIGATwoPort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.8 | Nodees1200ModuleLXGIGAOnePort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.9 | Nodees1200ModuleLXGIGATwoPort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.10 | Nodees1200ModuleTXGIGAOnePort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.11 | Nodees1200ModuleTXGIGATwoPort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.12 | Nodees1200ModuleNone | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5 | Nodees1210ModuleRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.1 | Nodees1210ModuleMainboardTx | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.2 | Nodees1210ModuleTxTwoPort | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.3 | Nodees1210ModuleFxSC | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.4 | Nodees1210ModuleFxMTRJ | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.5 | Nodees1210ModuleSIO | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.6 | Nodees1210ModuleNone | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6 | Nodees1200PortRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.1 | Nodees1200Port-10-100TX | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.2 | Nodees1200Port-100-SC | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.3 | Nodees1200Port-100-MTRJ | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.4 | Nodees1200Port-1000-SX | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.5 | Nodees1200Port-1000-LX | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.6 | Nodees1200Port-1000-TX | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7 | Nodees1210PortRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7.1 | Nodees1210Port-10-100TX | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7.2 | Nodees1210Port-100-SC | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7.3 | Nodees1210Port-100-MTRJ | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.8 | Nodees1200PowerSupplyRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.8.1 | Nodees1200PowerSupply | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.9 | Nodees1210PowerSupplyRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.9.1 | Nodees1210PowerSupply | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.10 | Nodees1200FanRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.10.1 | Nodees1200Fan | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.11 | Nodees1210FanRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.11.1 | Nodees1210Fan | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12 | Nodees1200SlotRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12.1 | Nodees1200Slot1 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12.2 | Nodees1200Slot2 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12.3 | Nodees1200Slot3 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.13 | Nodees1210SlotRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.13.1 | Nodees1210Slot1 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.13.2 | Nodees1210Slot2 | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.14 | Nodees1200SensorRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.1.25.15 | Nodees1200BackplaneRegistration | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2 | Nodefore-mgmt | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25 | Nodees1200Mgmt | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1 | NodeswStructure | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1 | NodeswStructInfo | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1.1 | ScalarswStructDevType | read-only | mandatory | Specifies the device type |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1.2 | ScalarswStructDevDescr | read-only | mandatory | Describes the type of the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1.3 | ScalarswStructPortEncodingFactor | read-only | mandatory | The factor to encode the global port ID from unit ID and the local port ID. This global port ID is required to access the bridge MIB and spanning tree MIB defi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2 | TableswStructUnitTable | not-accessible | mandatory | A table that contains information about a unit in the device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1 | RowswStructUnitEntry | not-accessible | mandatory | A list of information for each unit in the device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.1 | ColumnswStructUnitIndex | read-only | mandatory | ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.2 | ColumnswStructUnitType | read-only | mandatory | Type of the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.3 | ColumnswStructUnitDescr | read-only | mandatory | Type of the unit in displayed string format |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.4 | ColumnswStructUnitLedInfo | read-only | mandatory | Provides the LED information for the unit. Master: byte 0: bit 0:Condole in Use (0:not used,1:used) bit 1:Giga module status (0:not exist,1:exist) bit 2:Giga m… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.5 | ColumnswStructUnitMaxModuleNum | read-only | mandatory | Maximum number of modules allowed on the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.6 | ColumnswStructUnitMaxPortNum | read-only | mandatory | Maximum number of ports allowed on the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.7 | ColumnswStructUnitNumOfPortInUse | read-only | mandatory | Number of ports which has link being connected to the port |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.8 | ColumnswStructUnitOperStatus | read-only | mandatory | Describes the operation status for the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.9 | ColumnswStructUnitLastChange | read-only | mandatory | Provides the time that the unit is up last time |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3 | TableswStructModuleTable | not-accessible | mandatory | A table that contains information about a module. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1 | RowswStructModuleEntry | not-accessible | mandatory | A list of information for a module. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.1 | ColumnswStructModuleUnitIndex | read-only | mandatory | ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.2 | ColumnswStructModuleIndex | read-only | mandatory | ID of the Module in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.3 | ColumnswStructModuleSubMduIndex | read-only | mandatory | If the module doesnot contain sub module, sub module ID is 0. Otherwise, it indicates the ID of the sub module relative to the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.4 | ColumnswStructModuleType | read-only | mandatory | Type of the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.5 | ColumnswStructModuleDescr | read-only | mandatory | Type of the module in displayed string format |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.6 | ColumnswStructModuleVersion | read-only | mandatory | Provides PCB version of the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.7 | ColumnswStructModuleMaxPortNum | read-only | mandatory | Maximum number of ports allowed on the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.8 | ColumnswStructModuleEncodingOffset | read-only | mandatory | Each module has a offset for encoding the port ID relative to a unit. This encoding will provide a unigue port ID for ports located on the device. Example: sup… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.9 | ColumnswStructModuleOperStatus | read-only | mandatory | Provides operation status of the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.10 | ColumnswStructModuleLastChange | read-only | mandatory | Provides the time that the module is up last time |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4 | TableswStructPowerTable | not-accessible | mandatory | A table that contains information about every board. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1 | RowswStructPowerEntry | not-accessible | mandatory | A list of information for each board of the chassis. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1.1 | ColumnswStructPowerUnitIndex | read-only | mandatory | ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1.2 | ColumnswStructPowerIndex | read-only | mandatory | ID of the power supply in the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1.3 | ColumnswStructPowerOperStatus | read-only | mandatory | Describes the operation status of the power supply |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5 | TableswStructFanTable | not-accessible | mandatory | A table that contains information about every board. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1 | RowswStructFanEntry | not-accessible | mandatory | A list of information for each board of the chassis. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1.1 | ColumnswStructFanUnitIndex | read-only | mandatory | ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1.2 | ColumnswStructFanIndex | read-only | mandatory | ID of the fan in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1.3 | ColumnswStructFanOperStatus | read-only | mandatory | Describes the operation status of the fan |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2 | NodeswL2Mgmt | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1 | NodeswL2DevMgmt | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1 | NodeswL2DevCtrl | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.1 | ScalarswL2DevCtrlStpState | read-write | mandatory | This object can be enabled or disabled spanning tree algorithm during runtime of the system. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.2 | ScalarswL2DevCtrlPartitionModeState | read-write | mandatory | This object used to enable or disable port auto partition. When the object apply for all ports of the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.3 | ScalarswL2DevCtrlTableLockState | read-write | mandatory | This object indicates whether the address table is locked. In other words, the address table doesn't learn any more new address. The aging timer is suspended w… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.4 | ScalarswL2DevCtrlHOLState | read-write | mandatory | The object provides a way to prevent HOL (Head Of Line) blocking between ports. HOL protection may prevent forwarding a packet to a blocking port.The idea reli… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.5 | ScalarswL2DevCtrlAddrLookupModesAndHitRate | read-write | mandatory | According to the differnet address looke mode setting, to enlarge the address table size is possible in device. But there is side effect as the higher level yo… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.6 | ScalarswL2DevCtrlUploadImageFileName | read-write | mandatory | The name of the image file to be uploaded from the device to TFTP server when enabling image upload function (by writing swDevCtrlUploadImage). |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.7 | ScalarswL2DevCtrlUploadImage | write-only | mandatory | Image file upload control. Writing it by any value will immediately invoke image upload function. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.8 | ScalarswL2DevCtrlClearAddressTable | read-write | mandatory | This object indicates the agent clear address table. Setting this object to clear(2) will clear address table. The agent alwats return other(1) when this objec… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2 | NodeswL2DevAlarm | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.1 | ScalarswL2DevAlarmPartition | read-write | mandatory | Depending on this object, the device send a trap or not when any one of the device's ports was partitioned. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.2 | ScalarswL2DevAlarmNewRoot | read-write | mandatory | When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.3 | ScalarswL2DevAlarmTopChange | read-write | mandatory | This object determines to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device w… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.4 | ScalarswL2DevAlarmLinkChange | read-write | mandatory | This object determines to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4 | NodeswL2PortMgmt | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1 | TableswL2PortInfoTable | not-accessible | mandatory | A table that contains information about every port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1 | RowswL2PortInfoEntry | not-accessible | mandatory | A list of information for each port of the device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.1 | ColumnswL2PortInfoUnitIndex | read-only | mandatory | Indicates ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.2 | ColumnswL2PortInfoModuleIndex | read-only | mandatory | Indicates ID of the module on the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.3 | ColumnswL2PortInfoIndex | read-only | mandatory | Indicates ID of the port on the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.4 | ColumnswL2PortInfoType | read-only | mandatory | Indicates the connector type of this port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.5 | ColumnswL2PortInfoDescr | read-only | mandatory | Provides port type information in displayed string format |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.6 | ColumnswL2PortInfoLinkStatus | read-only | mandatory | Indicates port link status |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.7 | ColumnswL2PortInfoNwayStatus | read-only | mandatory | This object indicates the port speed and duplex mode. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2 | TableswL2PortCtrlTable | not-accessible | mandatory | A table that contains control information about every port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1 | RowswL2PortCtrlEntry | not-accessible | mandatory | A list of control information for each port of the device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.1 | ColumnswL2PortCtrlUnitIndex | read-only | mandatory | Indicates ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.2 | ColumnswL2PortCtrlModuleIndex | read-only | mandatory | Indicates ID of the module on the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.3 | ColumnswL2PortCtrlIndex | read-only | mandatory | This object indicates the device port number.(1..Max port number) |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.4 | ColumnswL2PortCtrlAdminState | read-write | mandatory | This object decides the port to be enabled or disabled. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.5 | ColumnswL2PortCtrlLinkStatusAlarmState | read-write | mandatory | Depends on this object to determine to send a trap or not when link status changes . |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.6 | ColumnswL2PortCtrlNwayState | read-write | mandatory | Chooses the port speed, duplex mode, and N-Way function mode. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.7 | ColumnswL2PortCtrlFlowCtrlState | read-write | mandatory | Sets IEEE 802.3x compliant flow control function as enabled or disabled. And IEEE 802.3x compliant flow control function work only when the port is in full dup… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.8 | ColumnswL2PortCtrlBackPressState | read-write | mandatory | Depends on this object to determine to enable or disable the backpressure function when the port is working in half duplex mode. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.9 | ColumnswL2PortCtrlLockState | read-write | mandatory | The state of this entry. The meanings of the values are: other(1) - this entry is currently in use but the conditions under which it will remain so are differe… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.10 | ColumnswL2PortCtrlPriority | read-write | mandatory | The priority queueing for packets received on this port, except for BPDU/IGMP packets and packets with unknown unicast destination address. IGMP and BPDU packe… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.11 | ColumnswL2PortCtrlStpState | read-write | mandatory | The state of STP(spanning tree algorithm) operation on this port. That's meaning the port whether add in the STP. The value enabled(3) indicates that STP is en… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.12 | ColumnswL2PortCtrlHOLState | read-write | mandatory | The object provides a way to prevent HOL (Head Of Line) blocking between ports. HOL protection may prevent forwarding a packet to a blocking port.The idea reli… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.13 | ColumnswL2PortCtrlBcastRisingAct | read-write | mandatory | This object indicates the system action when broadcast storm rising threshold is met. other(1) - this entry is currently in use but the conditions under which … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.14 | ColumnswL2PortCtrlBcastFallingAct | read-write | mandatory | This object indicates the device action when broadcast storm falling threshold is met. other(1) - this entry is currently in use but the conditions under which… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3 | TableswL2PortStTable | not-accessible | mandatory | A list of port statistic Counter entries. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1 | RowswL2PortStEntry | not-accessible | mandatory | This entry include all the port statistic Counter which support by the device, like Bytes received, Bytes Sent ... |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.1 | ColumnswL2PortStUnitIndex | read-only | mandatory | indicates ID of the unit in the device |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.2 | ColumnswL2PortStModuleIndex | read-only | mandatory | indicates ID of the module on the unit |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.3 | ColumnswL2PortStIndex | read-only | mandatory | This object indicates the device port number.(1..Max port number) |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.4 | ColumnswL2PortStByteRx | read-only | mandatory | swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every data octet of good packets(unicast + multi- cast + broadcast) received. … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.5 | ColumnswL2PortStByteTx | read-only | mandatory | This counter is incremented once for every data octet of a trans- mitted good packet. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.6 | ColumnswL2PortStFrameRx | read-only | mandatory | swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every good packet(unicast + multicast + broadcast ) received. swDevCtrlCounter… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.7 | ColumnswL2PortStFrameTx | read-only | mandatory | This counter is incremented once for every transmitted good packet. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.8 | ColumnswL2PortStTotalBytesRx | read-only | mandatory | This counter is incremented once for every data octet of all received packets. This include data octets of rejected and local packets which are not forwarded t… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.9 | ColumnswL2PortStTotalFramesRx | read-only | mandatory | This counter is incremented once for every received packets. This include rejected and local packets which are not forwarded to the switching core for transmis… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.10 | ColumnswL2PortStBroadcastFramesRx | read-only | mandatory | swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every good broadcast packet received. swDevCtrlCounterMode = 3(all-frames):Thi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.11 | ColumnswL2PortStMulticastFramesRx | read-only | mandatory | swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every good multicast packet received. swDevCtrlCounterMode = 3(all-frames):Thi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.12 | ColumnswL2PortStCRCError | read-only | mandatory | This counter is incremented once for every received packet which meets all the following conditions: 1.Packet data length is between 64 and 1518 bytes inclusiv… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.13 | ColumnswL2PortStOversizeFrames | read-only | mandatory | The number of good frames with length more than 1518 bytes. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.14 | ColumnswL2PortStFragments | read-only | mandatory | This counter is incremented once for every received packet which meets all the following conditions: 1.Packet data length is less than 64 bytes or packet witho… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.15 | ColumnswL2PortStJabber | read-only | mandatory | The number of frames with length more than 1518 bytes and with CRC error or misaligned. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.16 | ColumnswL2PortStCollision | read-only | mandatory | The number of Collisions |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.17 | ColumnswL2PortStLateCollision | read-only | mandatory | The number of Late Collision(collision occurring later than 576th transmitted bit). |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.18 | ColumnswL2PortStFrames-64-bytes | read-only | mandatory | This counter is incremented once for every received and trans- mitted packet with size of 64 bytes. This counter includes reject- ed received and transmitted p… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.19 | ColumnswL2PortStFrames-65-127-bytes | read-only | mandatory | This counter is incremented once for every received and trans- mitted packet with size of 65 to 127 bytes. This counter includes rejected received and transmit… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.20 | ColumnswL2PortStFrames-128-255-bytes | read-only | mandatory | This counter is incremented once for every received and trans- mitted packet with size of 128 to 255 bytes. This counter includes rejected received and transmi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.21 | ColumnswL2PortStFrames-256-511-bytes | read-only | mandatory | This counter is incremented once for every received and trans- mitted packet with size of 256 to 511 bytes. This counter includes rejected received and transmi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.22 | ColumnswL2PortStFrames-512-1023-bytes | read-only | mandatory | This counter is incremented once for every received and trans- mitted packet with size of 512 to 1023 bytes. This counter includ- es rejected received and tran… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.23 | ColumnswL2PortStFrames-1024-1536-bytes | read-only | mandatory | This counter is incremented once for every received and trans- mitted packet with size of 1024 to 1536 bytes. This counter includ- es rejected received and tra… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.24 | ColumnswL2PortStFramesDroppedFrames | read-only | mandatory | This counter is incremented once for every received dropped pack- et. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.25 | ColumnswL2PortStMulticastFramesTx | read-only | mandatory | The number of multicast frames sent. This counter does not include broadcast packets. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.26 | ColumnswL2PortStBroadcastFramesTx | read-only | mandatory | The number of broadcast frames sent. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.27 | ColumnswL2PortStUndersizeFrames | read-only | mandatory | This counter is incremented once for every received packet which meets all the following conditions: 1.Packet data length is less than 64 bytes. 2.Packet has v… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5 | NodeswPortSniff | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1 | TableswSniffCtrlTable | not-accessible | mandatory | A list of port sniffing entries.Port Sniffing function provides an easy way to monitor traffic on any port. In this way any good packets appears on the source … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1 | RowswSniffCtrlEntry | not-accessible | mandatory | Each entry contains a pair of sniff source port and target port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.1 | ColumnswSniffIndex | read-only | mandatory | A unique number to identify the sniff entry. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.2 | ColumnswSniffSourcePort | read-write | mandatory | Indicates the source port whose traffic will be sniffed. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.3 | ColumnswSniffTargetPort | read-write | mandatory | Indicates the target port which the traffic appears on the source sniffed port will be copied to. A trunk port member cannot be configured as a target Sniffing… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.4 | ColumnswSniffState | read-write | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6 | NodeswPortTrunk | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1 | TableswPortTrunkCtrlTable | not-accessible | mandatory | This table specifies which port trunking configuration. Trunking ID is as following : trunk 1 - unit1, base, port5~12; trunk 2 - unit1, base, port13~20; trunk … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1 | RowswPortTrunkCtrlEntry | not-accessible | mandatory | Each entry specifies which ports are grouped as a single logical link. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.1 | ColumnswPortTrunkCtrlIndex | read-only | mandatory | The index of logical trunk of ports. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.2 | ColumnswPortTrunkCtrlAnchorPort | read-write | mandatory | get anchor port number between trunk ports |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.3 | ColumnswPortTrunkCtrlMasterPort | read-only | mandatory | get master port number between trunk ports |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.4 | ColumnswPortTrunkCtrlName | read-write | mandatory | The name of logical trunk of ports. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.5 | ColumnswPortTrunkCtrlMember | read-write | mandatory | specifies the member ports which are grouped as a trunk. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.6 | ColumnswPortTrunkCtrlState | read-write | mandatory | This object determines whether the trunk setting is in enable/disable state. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2 | TableswPortTrunkMemberTable | not-accessible | mandatory | A list of information provide a different view for member ports grouped as a trunk |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1 | RowswPortTrunkMemberEntry | not-accessible | mandatory | Each entry corresponds to a member port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.1 | ColumnswPortTrunkMemberIndex | read-only | mandatory | Indicates the trunk ID where the port is located. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.2 | ColumnswPortTrunkMemberUnitIndex | read-only | mandatory | Indicates the unit ID where the port is located. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.3 | ColumnswPortTrunkMemberModuleIndex | read-only | mandatory | Indicates the module ID where the port is located. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.4 | ColumnswPortTrunkMemberPortIndex | read-only | mandatory | Indicates the port index relative to the module. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7 | NodeswIGMP | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.1 | NodeswIGMPCtrl | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.1.1 | ScalarswIGMPAdminState | read-write | mandatory | This object allows the user to enable/disable the IGMP snooping function. The IGMP function provided by the device includes both v1 and v2. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.1.2 | ScalarswIGMPTimeout | read-write | mandatory | The timeout value for sending IGMP query packet when no one was sent by the multicast router in the lan. The device will actively send the query message. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2 | TableswIGMPInfoTable | not-accessible | mandatory | The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1 | RowswIGMPInfoEntry | not-accessible | mandatory | Information about current IGMP query information, provided that swDevIGMPCaptureState and swIGMPCtrlState of associated VLAN entry are all enabled. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.1 | ColumnswIGMPInfoIndex | read-only | mandatory | This object indicates the IGMP query information entry number. It could be up to 12 entries, depending on current number of VLAN entries. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.2 | ColumnswIGMPInfoVid | read-only | mandatory | This object indicates the Vid of associated IGMP info table entry. It follows swIGMPCtrlVid in the associated entry of IGMP control table (swIGMPCtrlTable). |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.3 | ColumnswIGMPInfoQueryCount | read-only | mandatory | This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.4 | ColumnswIGMPInfoTxQueryCount | read-only | mandatory | This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to relate… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3 | TableswIGMPTable | not-accessible | mandatory | This table contains information regarding to the IGMP group membership report received by each port. The system will use the information recorded in this table… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1 | RowswIGMPEntry | not-accessible | mandatory | Each entry describes the ports which are member of a specific group address. Note that when a specific multicast address existing in the table also exist in th… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.1 | ColumnswIGMPVid | read-only | mandatory | This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.2 | ColumnswIGMPGroupIpAddr | read-only | mandatory | A IP multicast group address which has port membership in the underlying network. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.3 | ColumnswIGMPGroupMacAddr | read-only | mandatory | The multicast MAC address corresponds to swIGMPGroupIpAddr. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.4 | ColumnswIGMPPortMap | read-only | mandatory | Indicates the set of ports which are members of this multicast group. These ports are represented by a octet string.The most significant bit represents the low… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.5 | ColumnswIGMPIpGroupReportCount | read-only | mandatory | Indicates the number of group membership report packets received by the device corresponding to this multicast group. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4 | TableswIGMPCtrlTable | not-accessible | mandatory | The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swVlanInfoStatus). If VLAN is disabled or in Mac-Base mode, there is only… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1 | RowswIGMPCtrlEntry | not-accessible | mandatory | The entry in IGMP control table (swIGMPCtrlTable). The entry is effective only when IGMP capture switch is enabled. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.1 | ColumnswIGMPCtrlIndex | read-only | mandatory | This object indicates the IGMP control entry number.Its scale depends on current VLAN state (es400VlanInfoStatus). If VLAN is disabled or in Mac-Base mode, the… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.2 | ColumnswIGMPCtrlVid | read-write | mandatory | This object indicates the IGMP control entry's VLAN id. If VLAN is disabled or in Mac-Base mode, the Vid is always 0 and cannot be changed by management users.… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.3 | ColumnswIGMPCtrlTimer | read-write | mandatory | The timer value for sending IGMP query packet when none was sent by the multicast router in the LAN. The timer works in per-VLAN basis. Our device will be acti… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.4 | ColumnswIGMPCtrlState | read-write | mandatory | This object indicates the status of this entry. other(1) - This entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8 | NodeswVlan | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1 | NodeswVlanCtrl | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1.1 | ScalarswVlanCtrlMode | read-write | mandatory | This object controls which Vlan function will be enable (or disable) when the switch hub restart at the startup (power on) or warm start. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1.2 | ScalarswVlanInfoStatus | read-only | mandatory | This object indicates which Vlan function be enable (or disable) in mandatoryly stage. There are no effect when change swVlanCtrlMode vlaue in the system runni… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1.3 | ScalarswVlanSnmpPortVlan | read-write | mandatory | Indicates the Vlan which the SNMP port belongs to. The value range is 1 to 4094. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2 | NodeswMacBaseVlan | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.1 | NodeswMacBaseVlanInfo | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.1.1 | ScalarswMacBaseVlanMaxNum | read-only | mandatory | The maximum number of Mac base Vlan allowed by the system. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.1.2 | ScalarswMacBaseVlanAddrMaxNum | read-only | mandatory | The maximum number of entries in Mac-based Vlan address table. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2 | TableswMacBaseVlanCtrlTable | not-accessible | mandatory | A table that contains information about MAC base Vlan entries for which the switch has forwarding and/or filtering information. This information is used by the… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1 | RowswMacBaseVlanCtrlEntry | not-accessible | mandatory | A list of information about a specific MAC base Vlan configuration portlist for which the switch has some forwarding and/or filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1.1 | ColumnswMacBaseVlanDesc | read-only | mandatory | A textual description of the Mac Base Vlan for memorization. The string cannot set to empty string. There is a default value for this string |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1.2 | ColumnswMacBaseVlanMacMember | read-only | mandatory | This object indicates the total number of MAC addresses contained in the VLAN entry. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1.3 | ColumnswMacBaseVlanCtrlState | read-write | mandatory | This object indicates the MacBase Vlan state. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3 | TableswMacBaseVlanAddrTable | not-accessible | mandatory | A table that contains information about unicast or multicast entries for which the switch has forwarding and/or filtering information. This information is used… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1 | RowswMacBaseVlanAddrEntry | not-accessible | mandatory | A list of information about a specific unicast or multicast MAC address for which the switch has some forwarding and/or filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.1 | ColumnswMacBaseVlanAddr | read-only | mandatory | This object indictaes a unicast or multicast MAC address for which the bridge has forwarding and/or filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.2 | ColumnswMacBaseVlanAddrVlanDesc | read-write | mandatory | A textual description of the Mac Base Vlan for memorization . |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.3 | ColumnswMacBaseVlanAddrState | read-write | mandatory | This object indicates the MacBase Vlan Address entry state. other(1) - this entry is currently in use but the conditions under which it will remain so are diff… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.4 | ColumnswMacBaseVlanAddrStatus | read-only | mandatory | This object indicates the MacBase Vlan Address entry state. other(1) - this entry is currently in use but the conditions under which it will remain so are diff… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3 | NodeswPortBaseVlan | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.1 | ScalarswPortBaseVlanTotalNum | read-only | mandatory | The total number of Port-Base Vlan which is in enabled state within this switch hub. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2 | TableswPortBaseVlanDefaultVlanTable | not-accessible | mandatory | A table that contains default Port-Based VLAN list entries for the switch. The entry (Vid = 1,i.e. swPortBaseVlanDefaultPvid = 1) is defalut Port-Based VLAN , … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1 | RowswPortBaseVlanDefaultVlanEntry | not-accessible | mandatory | A list of default Port-Based VLAN information in swPortBaseVlanDefaultVlanTable. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.1 | ColumnswPortBaseVlanDefaultPvid | read-only | mandatory | This object indicates the default Port-Base Vlan ID. It occupies only 1 entry in VLAN table, with VID=1. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.2 | ColumnswPortBaseVlanDefaultDesc | read-only | mandatory | A textual description of the Port-Base Vlan. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.3 | ColumnswPortBaseVlanDefaultPortList | read-only | mandatory | This object indicates the port member set of the specified Vlan. Each Vlan has a octect string to indicate the port map. The most significant bit represents th… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.4 | ColumnswPortBaseVlanDefaultPortNumber | read-only | mandatory | This object indicates the number of ports of the entry. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3 | TableswPortBaseVlanConfigTable | not-accessible | mandatory | A table that contains Port-Based VLAN list entries for the switch. The device can't support port overlapping in Port-Based VLAN. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1 | RowswPortBaseVlanConfigEntry | not-accessible | mandatory | A list of information about a specific Port-Based VLAN configuration in swPortBaseVlanConfigTable. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.1 | ColumnswPortBaseVlanConfigPvid | read-only | mandatory | This object indicates the Port-Base Vlan ID. There are up to 11 entries for current product now. The object range varies from 2 to 12. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.2 | ColumnswPortBaseVlanConfigDesc | read-write | mandatory | A textual description of the Port-Base Vlan. It cannot be a null string. And each description must be unique in the table. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.3 | ColumnswPortBaseVlanConfigPortList | read-write | mandatory | This object indicates which ports are belong to the Vlan. Each Vlan has a octect string to indicate with port map. The most significant bit represents the lowe… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.4 | ColumnswPortBaseVlanConfigPortNumber | read-only | mandatory | This object indicates the number of ports of the entry. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4 | NodepBridgeMIBObjects | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1 | Nodedot1dExtBase | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.1 | Scalardot1dDeviceCapabilities | read-only | mandatory | Indicates the optional parts of IEEE 802.1D and 802.1Q that are implemented by this device and are managable through this MIB. Capabilities that are allowed on… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.2 | Scalardot1dTrafficClassesEnabled | read-only | mandatory | The value true(1) indicates that Traffic Classes are enabled on this bridge. When false(2), the bridge operates with a single priority level for all traffic. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.3 | Scalardot1dGmrpStatus | read-write | mandatory | The administrative status requested by management for GMRP. The value enabled(1) indicates that GMRP should be enabled on this device, in all VLANs, on all por… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.4 | Tabledot1dPortCapabilitiesTable | not-accessible | mandatory | A table that contains capabilities information about every port that is associated with this bridge. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.4.1 | Rowdot1dPortCapabilitiesEntry | not-accessible | mandatory | A set of capabilities information about this port indexed by dot1dBasePort. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.4.1.1 | Columndot1dPortCapabilities | read-only | mandatory | Indicates the parts of IEEE 802.1D and 802.1Q that are optional on a per-port basis that are implemented by this device and are managable through this MIB. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2 | Nodedot1dPriority | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2.1 | Tabledot1dPortPriorityTable | not-accessible | mandatory | A table that contains information about every port that is associated with this transparent bridge. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2.1.1 | Rowdot1dPortPriorityEntry | not-accessible | mandatory | A list of the number of egress traffic classes supported for each port in a transparent bridge. This is indexed by dot1dBasePort. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2.1.1.1 | Columndot1dPortNumTrafficClasses | read-only | mandatory | The number of egress traffic classes supported on this port. This object may optionally be read-only. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3 | Nodedot1dGarp | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1 | Tabledot1dPortGarpTable | not-accessible | mandatory | A table of GARP control information about every bridge port. This is indexed by dot1dBasePort. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1 | Rowdot1dPortGarpEntry | not-accessible | mandatory | GARP control information for a bridge port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1.1 | Columndot1dPortGarpJoinTime | read-write | mandatory | The GARP Join time, in centiseconds. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1.2 | Columndot1dPortGarpLeaveTime | read-write | mandatory | The GARP Leave time, in centiseconds. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1.3 | Columndot1dPortGarpLeaveAllTime | read-write | mandatory | The GARP LeaveAll time, in centiseconds. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4 | Nodedot1dGmrp | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1 | Tabledot1dPortGmrpTable | not-accessible | mandatory | A table of GMRP control and status information about every bridge port. Augments the dot1dBasePortTable. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1 | Rowdot1dPortGmrpEntry | not-accessible | mandatory | GMRP control and status information for a bridge port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1.1 | Columndot1dPortGmrpStatus | read-write | mandatory | The state of GMRP operation on this port. The value enabled(1) indicates that GMRP is enabled on this port, in all VLANs, as long as dot1dGmrpStatus is also en… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1.2 | Columndot1dPortGmrpFailedRegistrations | read-only | mandatory | The total number of failed GMRP registrations, for any reason, in all VLANs, on this port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1.3 | Columndot1dPortGmrpLastPduOrigin | read-only | mandatory | The Source MAC Address of the last GMRP message received on this port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5 | NodeqBridgeMIBObjects | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1 | Nodedot1qBase | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.1 | Scalardot1qVlanVersionNumber | read-only | mandatory | The version number of IEEE 802.1Q that this device supports. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.2 | Scalardot1qMaxVlanId | read-only | mandatory | The maximum IEEE 802.1Q VLAN ID that this device supports. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.3 | Scalardot1qMaxSupportedVlans | read-only | mandatory | The maximum number of IEEE 802.1Q VLANs that this device supports. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.4 | Scalardot1qNumVlans | read-only | mandatory | The current number of IEEE 802.1Q VLANs that are configured in this device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.5 | Scalardot1qGvrpStatus | read-write | mandatory | The administrative status requested by management for GVRP. The value enabled(1) indicates that GVRP should be enabled on this device, on all ports for which i… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2 | Nodedot1qTp | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1 | Tabledot1qFdbTable | not-accessible | mandatory | A table that contains configuration and control information for each Filtering Database currently operating on this device. Entries in this table appear automa… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1.1 | Rowdot1qFdbEntry | not-accessible | mandatory | Information about a specific Filtering Database. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1.1.1 | Columndot1qFdbId | not-accessible | mandatory | The identity of this Filtering Database. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1.1.2 | Columndot1qFdbDynamicCount | read-only | mandatory | The current number of dynamic entries in this Filtering Database. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2 | Tabledot1qTpFdbTable | not-accessible | mandatory | A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the trans… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1 | Rowdot1qTpFdbEntry | not-accessible | mandatory | Information about a specific unicast MAC address for which the device has some forwarding and/or filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1.1 | Columndot1qTpFdbAddress | not-accessible | mandatory | A unicast MAC address for which the device has forwarding and/or filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1.2 | Columndot1qTpFdbPort | read-only | mandatory | Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dot1qTpFdbAdd… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1.3 | Columndot1qTpFdbStatus | read-only | mandatory | The status of this entry. The meanings of the values are: other(1) - none of the following. This may include the case where some other MIB object (not the corr… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3 | Tabledot1qTpGroupTable | not-accessible | mandatory | A table containing filtering information for VLANs configured into the bridge by (local or network) management, or learnt dynamically, specifying the set of po… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1 | Rowdot1qTpGroupEntry | not-accessible | mandatory | Filtering information configured into the bridge by management, or learnt dynamically, specifying the set of ports to which frames received on a VLAN and conta… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1.1 | Columndot1qTpGroupAddress | not-accessible | mandatory | The destination Group MAC address in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1.2 | Columndot1qTpGroupEgressPorts | read-only | mandatory | The complete set of ports, in this Filtering Database, to which frames destined for this Group MAC address are currently being explicitly forwarded. This does … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1.3 | Columndot1qTpGroupLearnt | read-only | mandatory | The subset of ports in dot1qTpGroupEgressPorts which were learnt by GMRP or some other dynamic mechanism, in this Filtering database. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3 | Nodedot1qStatic | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2 | Tabledot1qStaticMulticastTable | not-accessible | mandatory | A table containing filtering information for Multicast and Broadcast MAC addresses for each VLAN, configured into the device by (local or network) management s… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1 | Rowdot1qStaticMulticastEntry | not-accessible | mandatory | Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from this specific port … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.1 | Columndot1qStaticMulticastAddress | not-accessible | mandatory | The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a Multicast or Broadcast address. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.2 | Columndot1qStaticMulticastReceivePort | not-accessible | mandatory | Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of z… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.3 | Columndot1qStaticMulticastStaticEgressPorts | read-write | mandatory | The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.4 | Columndot1qStaticMulticastForbiddenEgressPorts | read-write | mandatory | The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must not be forwarded, regardless… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.5 | Columndot1qStaticMulticastStatus | read-write | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the foll… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4 | Nodedot1qVlan | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.1 | Scalardot1qVlanNumDeletes | read-only | mandatory | The number of times a VLAN entry has been deleted from the dot1qVlanCurrentTable (for any reason). If an entry is deleted, then inserted, and then deleted, thi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2 | Tabledot1qVlanCurrentTable | not-accessible | mandatory | A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically create… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1 | Rowdot1qVlanCurrentEntry | not-accessible | mandatory | Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.1 | Columndot1qVlanTimeMark | not-accessible | mandatory | A TimeFilter for this entry. See the TimeFilter textual convention to see how this works. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.2 | Columndot1qVlanIndex | not-accessible | mandatory | The VLAN-ID or other identifier refering to this VLAN. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.3 | Columndot1qVlanFdbId | read-only | mandatory | The Filtering Database used by this VLAN. This is one of the dot1qFdbId values in the dot1qFdbTable. This value is allocated automatically by the device whenev… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.4 | Columndot1qVlanCurrentEgressPorts | read-only | mandatory | The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.5 | Columndot1qVlanCurrentUntaggedPorts | read-only | mandatory | The set of ports which are transmitting traffic for this VLAN as untagged frames. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.6 | Columndot1qVlanStatus | read-only | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the foll… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.7 | Columndot1qVlanCreationTime | read-only | mandatory | The value of sysUpTime when this VLAN was created. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3 | Tabledot1qVlanStaticTable | not-accessible | mandatory | A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and wi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1 | Rowdot1qVlanStaticEntry | not-accessible | mandatory | Static information for a VLAN configured into the device by (local or network) management. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.1 | Columndot1qVlanStaticName | read-write | mandatory | An administratively assigned string, which may be used to identify the VLAN. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.2 | Columndot1qVlanStaticEgressPorts | read-write | mandatory | The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Re… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.3 | Columndot1qVlanForbiddenEgressPorts | read-write | mandatory | The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be includ… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.4 | Columndot1qVlanStaticUntaggedPorts | read-write | mandatory | The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (VlanId 001) is a string… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.5 | Columndot1qVlanStaticRowState | read-write | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4 | Tabledot1qPortVlanTable | not-accessible | mandatory | A table containing per port control and status information for VLAN configuration in the device. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1 | Rowdot1qPortVlanEntry | not-accessible | mandatory | Information controlling VLAN configuration for a port on the device. This is indexed by dot1dBasePort. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.1 | Columndot1qPvid | read-write | mandatory | The PVID, the VLAN ID assigned to untagged frames or Prority-Tagged frames received on this port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.2 | Columndot1qPortIngressFiltering | read-write | mandatory | When this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept al… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.3 | Columndot1qPortGvrpStatus | read-write | mandatory | The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.4 | Columndot1qPortGvrpFailedRegistrations | read-only | mandatory | The total number of failed GVRP registrations, for any reason, on this port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.5 | Columndot1qPortGvrpLastPduOrigin | read-only | mandatory | The Source MAC Address of the last GVRP message received on this port. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9 | NodeswFDB | |||
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1 | TableswFdbStaticTable | not-accessible | mandatory | This table defines for frames with specific destincation MAC address, the set of ports that the frame will be forwarded to. Note that if a MAC address appears … |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1 | RowswFdbStaticEntry | not-accessible | mandatory | A list of information specifies which ports the frames with specific destination MAC address to go. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.1 | ColumnswFdbStaticVid | read-only | mandatory | This object indicates the VLAN-ID. If the swVlanInfoStatus is port-base mode , the object ranges from 1 to 12. If VLAN is in mac-based mode or disabled, the ob… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.2 | ColumnswFdbStaticAddress | read-only | mandatory | The MAC address which this forwarding entry applied. It can be an unicast address or a multicast address. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.3 | ColumnswFdbStaticPortMap | read-write | mandatory | The set of ports to which frames received containing the value of swFdbStaticAddress as the DA, are allowed to be forwarded. Each octet within the value of thi… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.4 | ColumnswFdbStaticJoinIGMPSnooping | read-write | mandatory | This object indicates whether to allow ports to join/leave IGMP group via IGMP Snooping. For a multicast address entry, port group could be classified into two… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.5 | ColumnswFdbStaticState | read-write | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.6 | ColumnswFdbStaticStatus | read-only | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2 | TableswFdbStaticMemberTable | not-accessible | mandatory | A list of information provide a different view for those ports where packets from the given Vlan need to be forwarded to. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1 | RowswFdbStaticMemberEntry | not-accessible | mandatory | A list of MIB capability entries supported by this forwarding static table. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.1 | ColumnswFdbStaticMemberVid | read-only | mandatory | This object indicates the VLAN-ID. If the swVlanInfoStatus is port-base mode , the object ranges from 1 to 12. If VLAN is in mac-based mode or disabled, the ob… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.2 | ColumnswFdbStaticMemberAddress | read-only | mandatory | The MAC address which this forwarding entry applied. It can be an unicast address or a multicast address. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.3 | ColumnswFdbStaticMemberUnitIndex | read-only | mandatory | Specifies the unit ID where the port is located |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.4 | ColumnswFdbStaticMemberModuleIndex | read-only | mandatory | Specifies the module ID where the port is located |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.5 | ColumnswFdbStaticMemberPortIndex | read-only | mandatory | Specifies the port index relative to the module |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3 | TableswFdbFilterTable | not-accessible | mandatory | This table defines information for the device to filter packets with specific MAC address (either as the DA or as the SA). The MAC address can be a unicast add… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1 | RowswFdbFilterEntry | not-accessible | mandatory | A list of information about a specific unicast/multicast MAC address for which the switch has filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1.1 | ColumnswFdbFilterVid | read-only | mandatory | This object indicates the VLAN-ID. If the swVlanInfoStatus is port-base mode , the object ranges from 1 to 12. If VLAN is in mac-based mode or disabled, the ob… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1.2 | ColumnswFdbFilterAddress | read-only | mandatory | This object indicates a unicast/multicast MAC address for which the bridge has filtering information. |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1.3 | ColumnswFdbFilterState | read-write | mandatory | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.326.2.20.1.2.2.2.25.9999 | ScalarendOfMIB | read-only | optional |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| EnabledStatus | INTEGER { enabled(1), disabled(2) } | ||
| PortList | OCTET STRING(SIZE(12)) | ||
| TimeFilter | INTEGER | ||
| TimeInterval | INTEGER | ||
| TruthValue | INTEGER { true(1), false(2) } | ||
| Unsigned32 | INTEGER | ||
| VlanId | INTEGER (1..4094) | ||
| VlanIndex | INTEGER (1..4094) |