ES4612-MIB
837 objects
The MIB module for ES4612.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.259 | Nodeaccton | |||
| 1.3.6.1.4.1.259.6 | NodesnmpMgt | |||
| 1.3.6.1.4.1.259.6.10 | NodecheetahSwitchMgt | |||
| 1.3.6.1.4.1.259.6.10.57 | Identityes4612MIB | The MIB module for ES4612. | ||
| 1.3.6.1.4.1.259.6.10.57.1 | Nodees4612MIBObjects | |||
| 1.3.6.1.4.1.259.6.10.57.1.1 | NodeswitchMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.1.1 | ScalarswitchManagementVlan | read-write | current | The VLAN on which management is done. |
| 1.3.6.1.4.1.259.6.10.57.1.1.2 | ScalarswitchNumber | read-only | current | The total number of switches present on this system. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3 | TableswitchInfoTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1 | RowswitchInfoEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.1 | ColumnswUnitIndex | not-accessible | current | This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.2 | ColumnswHardwareVer | read-only | current | Hardware version of the main board. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.3 | ColumnswMicrocodeVer | read-only | current | Microcode version of the main board. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.4 | ColumnswLoaderVer | read-only | current | Loader version of the main board. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.5 | ColumnswBootRomVer | read-only | current | Boot ROM code version of the main board. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.6 | ColumnswOpCodeVer | read-only | current | Operation code version of the main board. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.7 | ColumnswPortNumber | read-only | current | The total port number of this switch (including expansion slot). |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.8 | ColumnswPowerStatus | read-only | current | Indicates the switch using internalPower(1), redundantPower(2) or both(3) |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.9 | ColumnswRoleInSystem | read-only | current | Indicates the switch is master(1), backupMaster(2) or slave(3) in this system. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.10 | ColumnswSerialNumber | read-only | current | Serial number of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.11 | ColumnswExpansionSlot1 | read-only | current | Type of expansion module in this switch slot 1. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.12 | ColumnswExpansionSlot2 | read-only | current | Type of expansion module in this switch slot 2. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.13 | ColumnswServiceTag | read-only | current | Service tag serial-number of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.1.3.1.14 | ColumnswModelNumber | read-only | current | Model number of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.1.4 | ScalarswitchOperState | read-only | current | Global operation state of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.1.5 | NodeswitchProductId | |||
| 1.3.6.1.4.1.259.6.10.57.1.1.5.1 | ScalarswProdName | read-only | current | |
| 1.3.6.1.4.1.259.6.10.57.1.1.5.2 | ScalarswProdManufacturer | read-only | current | |
| 1.3.6.1.4.1.259.6.10.57.1.1.5.3 | ScalarswProdDescription | read-only | current | |
| 1.3.6.1.4.1.259.6.10.57.1.1.5.4 | ScalarswProdVersion | read-only | current | |
| 1.3.6.1.4.1.259.6.10.57.1.1.5.5 | ScalarswProdUrl | read-only | current | |
| 1.3.6.1.4.1.259.6.10.57.1.1.5.6 | ScalarswIdentifier | read-only | current | A unique identifier of which switch in the chassis is currently being looked at. |
| 1.3.6.1.4.1.259.6.10.57.1.1.5.7 | ScalarswChassisServiceTag | read-only | current | The service tag of the chassis this switch resides in. |
| 1.3.6.1.4.1.259.6.10.57.1.1.6 | TableswitchIndivPowerTable | not-accessible | current | Table about statuses of individual powers. |
| 1.3.6.1.4.1.259.6.10.57.1.1.6.1 | RowswitchIndivPowerEntry | not-accessible | current | Table about statuses of individual powers. |
| 1.3.6.1.4.1.259.6.10.57.1.1.6.1.1 | ColumnswIndivPowerUnitIndex | accessible-for-notify | current | This is defined as swUnitIndex. |
| 1.3.6.1.4.1.259.6.10.57.1.1.6.1.2 | ColumnswIndivPowerIndex | accessible-for-notify | current | 1 means internal power. 2 means external power. |
| 1.3.6.1.4.1.259.6.10.57.1.1.6.1.3 | ColumnswIndivPowerStatus | read-only | current | notPresent(1) means not present. green(2) means up. red(3) means down. |
| 1.3.6.1.4.1.259.6.10.57.1.1.7 | ScalarswitchJumboFrameStatus | read-write | current | enable(1) means the Jumbo Frame has enabled, disabled(2) means the Jumbo Frame has disabled. |
| 1.3.6.1.4.1.259.6.10.57.1.1.8 | NodeamtrMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.1.8.3 | ScalaramtrMacAddrAgingStatus | read-write | current | If this is enabled(1), the MAC address table will age out according to its timer. If this is disabled(2), the MAC address table will not age out. |
| 1.3.6.1.4.1.259.6.10.57.1.1.9 | TableswitchFanTable | not-accessible | current | The table of Fan Status. |
| 1.3.6.1.4.1.259.6.10.57.1.1.9.1 | RowswitchFanEntry | not-accessible | current | A conceptual row of the switchFanTable. |
| 1.3.6.1.4.1.259.6.10.57.1.1.9.1.1 | ColumnswitchUnitIndex | accessible-for-notify | current | the unit of the switch for stackable device. |
| 1.3.6.1.4.1.259.6.10.57.1.1.9.1.2 | ColumnswitchFanIndex | accessible-for-notify | current | The unit number of the fan. |
| 1.3.6.1.4.1.259.6.10.57.1.1.9.1.3 | ColumnswitchFanStatus | read-only | current | Indicating the status of the fan, 1:ok; 2:failure. |
| 1.3.6.1.4.1.259.6.10.57.1.2 | NodeportMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.2.1 | TableportTable | not-accessible | current | Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains informa… |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1 | RowportEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.1 | ColumnportIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.2 | ColumnportName | read-write | current | Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later). |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.3 | ColumnportType | read-only | current | Indicates the port type. |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.4 | ColumnportSpeedDpxCfg | read-write | current | Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 1… |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.5 | ColumnportFlowCtrlCfg | read-write | current | (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPr… |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.6 | ColumnportCapabilities | read-write | current | Port capabilities. |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.7 | ColumnportAutonegotiation | read-write | current | Whether autonegotiation is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.8 | ColumnportSpeedDpxStatus | read-only | current | The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk … |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.9 | ColumnportFlowCtrlStatus | read-only | current | (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trun… |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.10 | ColumnportTrunkIndex | read-only | current | The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to… |
| 1.3.6.1.4.1.259.6.10.57.1.2.1.1.12 | ColumnportComboForcedMode | read-write | current | This determines the forced mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect… |
| 1.3.6.1.4.1.259.6.10.57.1.3 | NodetrunkMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.3.1 | ScalartrunkMaxId | read-only | current | The maximum number for a trunk identifier. |
| 1.3.6.1.4.1.259.6.10.57.1.3.2 | ScalartrunkValidNumber | read-only | current | The number of valid trunks. |
| 1.3.6.1.4.1.259.6.10.57.1.3.3 | TabletrunkTable | not-accessible | current | Table of descriptive and status information about configuration of each trunk, similar to Cisco EtherChannel. |
| 1.3.6.1.4.1.259.6.10.57.1.3.3.1 | RowtrunkEntry | not-accessible | current | An entry in the table, containing information about configuration in one trunk of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.3.3.1.1 | ColumntrunkIndex | not-accessible | current | This object identifies the trunk within the switch for which this entry contains information. |
| 1.3.6.1.4.1.259.6.10.57.1.3.3.1.2 | ColumntrunkPorts | read-create | current | The complete set of ports currently associated with this trunk. |
| 1.3.6.1.4.1.259.6.10.57.1.3.3.1.3 | ColumntrunkCreation | read-only | current | A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk. |
| 1.3.6.1.4.1.259.6.10.57.1.3.3.1.4 | ColumntrunkStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.4 | NodelacpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.4.1 | TablelacpPortTable | not-accessible | current | Table for LACP port configuration. |
| 1.3.6.1.4.1.259.6.10.57.1.4.1.1 | RowlacpPortEntry | not-accessible | current | Entry for LACP port configuration. |
| 1.3.6.1.4.1.259.6.10.57.1.4.1.1.1 | ColumnlacpPortIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.4.1.1.2 | ColumnlacpPortStatus | read-write | current | Whether 802.3ad LACP is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.5 | NodestaMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.5.1 | ScalarstaSystemStatus | read-write | current | Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.259.6.10.57.1.5.2 | TablestaPortTable | not-accessible | current | The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType. |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1 | RowstaPortEntry | not-accessible | current | The conceptual entry of staPortTable. |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.1 | ColumnstaPortIndex | not-accessible | current | The port and the trunk (excluding trunk member ports) interface of the staPortTable. The interface identified by a particular value of this index is the same i… |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.2 | ColumnstaPortFastForward | read-write | current | Whether fast forwarding is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.3 | ColumnstaPortProtocolMigration | read-write | current | When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effe… |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.4 | ColumnstaPortAdminEdgePort | read-write | current | The administrative value of the edge port parameter. A value of true(1) indicates that this port should be assumed as an edge-port and a value of false(2) indi… |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.5 | ColumnstaPortOperEdgePort | read-only | current | The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received. |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.6 | ColumnstaPortAdminPointToPoint | read-write | current | The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as… |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.7 | ColumnstaPortOperPointToPoint | read-only | current | The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection… |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.8 | ColumnstaPortLongPathCost | read-write | current | The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to confi… |
| 1.3.6.1.4.1.259.6.10.57.1.5.2.1.9 | ColumnstaPortSystemStatus | read-write | current | Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.259.6.10.57.1.5.3 | ScalarstaProtocolType | read-write | current | The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'… |
| 1.3.6.1.4.1.259.6.10.57.1.5.4 | ScalarstaTxHoldCount | read-write | current | The value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.259.6.10.57.1.5.5 | ScalarstaPathCostMethod | read-write | current | Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the spanning tree protocol running on the sw… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6 | NodexstMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.5.6.1 | ScalarmstName | read-write | current | The name of the Multiple Spanning Tree region. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.2 | ScalarmstRevision | read-write | current | The Revision number of the Multiple Spanning Tree region. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.3 | ScalarmstMaxHops | read-write | current | The max hop number counts of the Multiple Spanning Tree region. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4 | TablexstInstanceCfgTable | not-accessible | current | This table is used to configure the property of a specific instance in Multiple Spanning Tree or Rapid Spanning Tree. If Rapid Spanning Tree protocol is in use… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1 | RowxstInstanceCfgEntry | not-accessible | current | A conceptual row containing the property of the RST or MST instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.1 | ColumnxstInstanceCfgIndex | not-accessible | current | An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.2 | ColumnxstInstanceCfgPriority | read-write | current | The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.3 | ColumnxstInstanceCfgTimeSinceTopologyChange | read-only | current | The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.4 | ColumnxstInstanceCfgTopChanges | read-only | current | The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.5 | ColumnxstInstanceCfgDesignatedRoot | read-only | current | The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol ( 802.1w … |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.6 | ColumnxstInstanceCfgRootCost | read-only | current | The cost of the path to the root as seen from this bridge of the RST or MST. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.7 | ColumnxstInstanceCfgRootPort | read-only | current | The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.8 | ColumnxstInstanceCfgMaxAge | read-only | current | The maximum age of Multiple Spanning Tree Protocol ( 802.1s ) or Rapid Spanning Tree Protocol ( 802.1w ) information learned from the network on any port befor… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.9 | ColumnxstInstanceCfgHelloTime | read-only | current | The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying t… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.10 | ColumnxstInstanceCfgHoldTime | read-only | current | This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredth… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.11 | ColumnxstInstanceCfgForwardDelay | read-only | current | For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards … |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.12 | ColumnxstInstanceCfgBridgeMaxAge | read-only | current | For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 speci… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.13 | ColumnxstInstanceCfgBridgeHelloTime | read-only | current | For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.14 | ColumnxstInstanceCfgBridgeForwardDelay | read-only | current | For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-19… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.15 | ColumnxstInstanceCfgTxHoldCount | read-only | current | For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.4.1.16 | ColumnxstInstanceCfgPathCostMethod | read-only | current | For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree pro… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5 | TablexstInstancePortTable | not-accessible | current | The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1 | RowxstInstancePortEntry | not-accessible | current | The conceptual row for xstInstancePortTable. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.1 | ColumnxstInstancePortInstance | not-accessible | current | The instance of the MSTP. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.2 | ColumnxstInstancePortPort | not-accessible | current | The port and the trunk (excluding trunk member ports) interface of the mstInstancePortTable. The interface identified by a particular value of this index is th… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.3 | ColumnxstInstancePortPriority | read-write | current | Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest prior… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.4 | ColumnxstInstancePortState | read-only | current | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discard… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.5 | ColumnxstInstancePortEnable | read-only | current | The enabled/disabled status of the port. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.6 | ColumnxstInstancePortPathCost | read-write | current | The pathcost of the RST or MST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should b… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.7 | ColumnxstInstancePortDesignatedRoot | read-only | current | The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the po… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.8 | ColumnxstInstancePortDesignatedCost | read-only | current | The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.9 | ColumnxstInstancePortDesignatedBridge | read-only | current | The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.10 | ColumnxstInstancePortDesignatedPort | read-only | current | The port identifier of the port on the designated bridge for this port's segment. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.11 | ColumnxstInstancePortForwardTransitions | read-only | current | The number of times this port has transitioned from the learning state to the forwarding state. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.5.1.12 | ColumnxstInstancePortPortRole | read-only | current | The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the b… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6 | TablemstInstanceEditTable | not-accessible | current | The Multiple Spanning Tree region instance vlan configuration table. Please read the actual instance vlan mapped in the mstInstanceOperTable. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1 | RowmstInstanceEditEntry | not-accessible | current | A conceptual row containing the status of the MSTP instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1.1 | ColumnmstInstanceEditIndex | not-accessible | current | An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1.2 | ColumnmstInstanceEditVlansMap | read-create | current | A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through … |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1.3 | ColumnmstInstanceEditVlansMap2k | read-create | current | A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1.4 | ColumnmstInstanceEditVlansMap3k | read-create | current | A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1.5 | ColumnmstInstanceEditVlansMap4k | read-create | current | A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.6.1.6 | ColumnmstInstanceEditRemainingHops | read-only | current | The remaining hop count for this MST instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7 | TablemstInstanceOperTable | not-accessible | current | The Multiple Spanning Tree region instance vlan mapped table. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7.1 | RowmstInstanceOperEntry | not-accessible | current | A conceptual row containing the status of the MSTP instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7.1.1 | ColumnmstInstanceOperIndex | not-accessible | current | An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance. |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7.1.2 | ColumnmstInstanceOperVlansMap | read-only | current | A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through … |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7.1.3 | ColumnmstInstanceOperVlansMap2k | read-only | current | A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7.1.4 | ColumnmstInstanceOperVlansMap3k | read-only | current | A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values… |
| 1.3.6.1.4.1.259.6.10.57.1.5.6.7.1.5 | ColumnmstInstanceOperVlansMap4k | read-only | current | A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values… |
| 1.3.6.1.4.1.259.6.10.57.1.7 | NoderestartMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.7.1 | ScalarrestartOpCodeFile | read-write | current | Name of op-code file for start-up. |
| 1.3.6.1.4.1.259.6.10.57.1.7.2 | ScalarrestartConfigFile | read-write | current | Name of configuration file for start-up. |
| 1.3.6.1.4.1.259.6.10.57.1.7.3 | ScalarrestartControl | read-write | current | Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Se… |
| 1.3.6.1.4.1.259.6.10.57.1.8 | NodemirrorMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.8.1 | TablemirrorTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.259.6.10.57.1.8.1.1 | RowmirrorEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.259.6.10.57.1.8.1.1.1 | ColumnmirrorDestinationPort | not-accessible | current | Destination port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.8.1.1.2 | ColumnmirrorSourcePort | not-accessible | current | Source port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.8.1.1.3 | ColumnmirrorType | read-create | current | If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and… |
| 1.3.6.1.4.1.259.6.10.57.1.8.1.1.4 | ColumnmirrorStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.9 | NodeigmpSnoopMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.9.1 | ScalarigmpSnoopStatus | read-write | current | Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.2 | ScalarigmpSnoopQuerier | read-write | current | Whether to act as querier. |
| 1.3.6.1.4.1.259.6.10.57.1.9.3 | ScalarigmpSnoopQueryCount | read-write | current | Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.4 | ScalarigmpSnoopQueryInterval | read-write | current | Query interval. |
| 1.3.6.1.4.1.259.6.10.57.1.9.5 | ScalarigmpSnoopQueryMaxResponseTime | read-write | current | Timeout value (seconds) between IGMP reports received on a port for an IP Multicast Address that can pass before the system sends an IGMP Query out the port an… |
| 1.3.6.1.4.1.259.6.10.57.1.9.6 | ScalarigmpSnoopQueryTimeout | read-write | current | Query time-out. |
| 1.3.6.1.4.1.259.6.10.57.1.9.7 | ScalarigmpSnoopVersion | read-write | current | Version. |
| 1.3.6.1.4.1.259.6.10.57.1.9.8 | TableigmpSnoopRouterCurrentTable | not-accessible | current | Table for current router ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.8.1 | RowigmpSnoopRouterCurrentEntry | not-accessible | current | Entry for current router ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.8.1.1 | ColumnigmpSnoopRouterCurrentVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.9.8.1.2 | ColumnigmpSnoopRouterCurrentPorts | read-only | current | The set of ports which are current router ports. Within this list, some router ports are static router ports. Please refer to igmpSnoopRouterStaticTable. |
| 1.3.6.1.4.1.259.6.10.57.1.9.8.1.3 | ColumnigmpSnoopRouterCurrentStatus | read-only | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.9 | TableigmpSnoopRouterStaticTable | not-accessible | current | Table for static router ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.9.1 | RowigmpSnoopRouterStaticEntry | not-accessible | current | Entry for static router ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.9.1.1 | ColumnigmpSnoopRouterStaticVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.9.9.1.2 | ColumnigmpSnoopRouterStaticPorts | read-create | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.259.6.10.57.1.9.9.1.3 | ColumnigmpSnoopRouterStaticStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.9.10 | TableigmpSnoopMulticastCurrentTable | not-accessible | current | Table for current multicast addresses. |
| 1.3.6.1.4.1.259.6.10.57.1.9.10.1 | RowigmpSnoopMulticastCurrentEntry | not-accessible | current | Entry for current multicast addresses. |
| 1.3.6.1.4.1.259.6.10.57.1.9.10.1.1 | ColumnigmpSnoopMulticastCurrentVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.9.10.1.2 | ColumnigmpSnoopMulticastCurrentIpAddress | not-accessible | current | IP address of multicast group. |
| 1.3.6.1.4.1.259.6.10.57.1.9.10.1.3 | ColumnigmpSnoopMulticastCurrentPorts | read-only | current | The set of ports which are members. |
| 1.3.6.1.4.1.259.6.10.57.1.9.10.1.4 | ColumnigmpSnoopMulticastCurrentStatus | read-only | current | The set of ports which are static members. |
| 1.3.6.1.4.1.259.6.10.57.1.9.11 | TableigmpSnoopMulticastStaticTable | not-accessible | current | Table for static multicast addresses. |
| 1.3.6.1.4.1.259.6.10.57.1.9.11.1 | RowigmpSnoopMulticastStaticEntry | not-accessible | current | Entry for static multicast addresses. |
| 1.3.6.1.4.1.259.6.10.57.1.9.11.1.1 | ColumnigmpSnoopMulticastStaticVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.9.11.1.2 | ColumnigmpSnoopMulticastStaticIpAddress | not-accessible | current | IP address of multicast group. |
| 1.3.6.1.4.1.259.6.10.57.1.9.11.1.3 | ColumnigmpSnoopMulticastStaticPorts | read-create | current | The set of ports which are members. |
| 1.3.6.1.4.1.259.6.10.57.1.9.11.1.4 | ColumnigmpSnoopMulticastStaticStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.10 | NodeipMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.10.2 | ScalarnetDefaultGateway | read-write | current | The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0. |
| 1.3.6.1.4.1.259.6.10.57.1.10.3 | ScalaripHttpState | read-write | current | Whether HTTP is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.10.4 | ScalaripHttpPort | read-write | current | The port number for HTTP. |
| 1.3.6.1.4.1.259.6.10.57.1.10.5 | ScalaripDhcpRestart | read-write | current | Write it to restart(1) to restart DHCP. When read, this value always returns noRestart(2). |
| 1.3.6.1.4.1.259.6.10.57.1.10.6 | ScalaripHttpsState | read-write | current | Whether HTTPS is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.10.7 | ScalaripHttpsPort | read-write | current | The port number for HTTPS. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11 | NodedhcpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1 | NodedhcpClient | |||
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1.1 | NodedhcpcOptions | |||
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1.1.1 | TabledhcpcInterfaceTable | not-accessible | current | Table for DHCP client information listed by interface. Depending on the nature of the product, this table may have only one entry(e.g. for the management VLAN)… |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1.1.1.1 | RowdhcpcInterfaceEntry | not-accessible | current | Entry for DHCP client information listed by interface. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1.1.1.1.1 | ColumndhcpcIfIndex | not-accessible | current | This is defined by ifIndex in the IF-MIB.(static vlan if index) |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1.1.1.1.2 | ColumndhcpcIfClientIdMode | read-write | current | Whether the Client ID is in text mode or in Hex mode. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.1.1.1.1.3 | ColumndhcpcIfClientId | read-write | current | The value that the DHCP client sets in the client_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to uniquely identi… |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2 | NodedhcpRelay | |||
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2.2 | TabledhcpRelayServerAddrTable | not-accessible | current | The role of DHCP Relay Agent is to forward requests and replies between server and client when they are not in the same subnet. To enable DHCP Relay service us… |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2.2.1 | RowdhcpRelayServerAddrEntry | not-accessible | current | A conceptual row of dhcpRelayServerAddrTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2.2.1.1 | ColumndhcpRelayServerAddrIfIndex | not-accessible | current | The VLAN interface being used by this table entry. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2.2.1.2 | ColumndhcpRelayServerAddrIndex | not-accessible | current | The Index of the Relay server IP address. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2.2.1.3 | ColumndhcpRelayServerAddrServerIp | read-write | current | The IP address of the relay server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.2.3 | ScalardhcpRelayRestart | read-write | current | Set to restart(1) to restart DCHP Relay. Always get noRestart(2) when you read this variable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3 | NodedhcpServerMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1 | TabledhcpPoolTable | not-accessible | current | A dhcp pool is a collection of user configuration such as option config-lease time or dns-server IPs, a network address for network pool, or a host IP plus a h… |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1 | RowdhcpPoolEntry | not-accessible | current | A conceptual row of dhcpPoolTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.1 | ColumndhcpPoolPoolName | not-accessible | current | PoolName, simply specify a string which string size NO MORE THAN 8 |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.2 | ColumndhcpPoolPoolType | read-create | current | Pool Type: notSpecify(1); netWork(2);host(3) |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.3 | ColumndhcpPoolPoolAddress | read-create | current | Pool Address |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.4 | ColumndhcpPoolSubnetMask | read-create | current | Subnet Mask |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.5 | ColumndhcpPoolHardwareType | read-create | current | Hardware type: notSpecify(1); ethernet(2); ieee802(3); fddi(4) |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.6 | ColumndhcpPoolMacAddress | read-create | current | MAC address |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.1.1.7 | ColumndhcpPoolstatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2 | TabledhcpPoolOptionTable | not-accessible | current | This is the Option table of the dhcpPoolTable, user can specify Options configuration in this table |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1 | RowdhcpPoolOptionEntry | not-accessible | current | A conceptual row of dhcpPoolOptionTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.1 | ColumndhcpPoolOptionPoolName | not-accessible | current | PoolName, simply specify a string which string size NO MORE THAN 8 |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.2 | ColumndhcpPoolOptionNextServer | read-write | current | Specifies the IP address of the next server in the boot process, which is typically a Trivial File Transfer Protocol(TFTP) server. One IP address is required. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.3 | ColumndhcpPoolOptionNetbiosNodeType | read-write | current | Specifies the NetBIOS node type. Valid types are: none(1) b-node(2) - Broadcast p-node(3) - Peer-to-peer m-node(4) - Mixed h-node(5) - Hybrid. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.4 | ColumndhcpPoolOptionDomainName | read-write | current | Specifies the domain name string. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.5 | ColumndhcpPoolOptionBootFile | read-write | current | To specify the name of the default boot image. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.6 | ColumndhcpPoolOptionLeaseTime | read-write | current | To configure the duration of the lease of an IP address that is assigned from a DHCP Server to a DHCP client. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.7 | ColumndhcpPoolOptionCidMode | read-write | current | Set this variable to text(2) of hex(3) to specify the mode of the Client Id, which is useful for CLI to determine the display way of the Client Id. You will ge… |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.2.1.8 | ColumndhcpPoolOptionCidBuffer | read-write | current | Content of Client Id. You MUST specify the dhcpPoolOptionCidMode before setting this variable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.3 | TabledhcpPoolOptionDnsSerTable | not-accessible | current | To specify the DNS IP servers available to a DHCP client, you can specify up to two addresses for each DHCP pool. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.3.1 | RowdhcpPoolOptionDnsSerEntry | not-accessible | current | A conceptual row of dhcpPoolOptionDnsSerTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.3.1.1 | ColumndhcpPoolOptionDnsSerPoolName | not-accessible | current | PoolName, simply specify a string which string size NO MORE THAN 8 |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.3.1.2 | ColumndhcpPoolOptionDnsSerIndex | not-accessible | current | Index of the DNS server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.3.1.3 | ColumndhcpPoolOptionDnsSerIpAddress | read-write | current | Ip address of the DNS server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.4 | TabledhcpPoolOptDefaultRouterTable | not-accessible | current | Specifices the default router list for a DHCP Client, you can specify up to two addresses for each DHCP pool. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.4.1 | RowdhcpPoolOptDefaultRouterEntry | not-accessible | current | A conceptual row of dhcpPoolOptDefaultRouterTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.4.1.1 | ColumndhcpPoolOptDefaultRouterPoolName | not-accessible | current | PoolName, simply specify a string which string size NO MORE THAN 8 |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.4.1.2 | ColumndhcpPoolOptDefaultRouterIndex | not-accessible | current | Index of the default router. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.4.1.3 | ColumndhcpPoolOptDefaultRouterIpAddress | read-write | current | Specifies the IP address of a router. One IP address is required. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.5 | TabledhcpPoolOptNetbiosServerTable | not-accessible | current | To configure the NetBIOS WINS name servers that are available to DHCP clients. You can specify up to eight addressed for each DHCP pool. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.5.1 | RowdhcpPoolOptNetbiosServerEntry | not-accessible | current | A conceptual row of dhcpPoolOptNetbiosServerTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.5.1.1 | ColumndhcpPoolOptNetbiosServerPoolName | not-accessible | current | PoolName, simply specify a string which string size NO MORE THAN 8 |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.5.1.2 | ColumndhcpPoolOptNetbiosServerIndex | not-accessible | current | Index of the Netbios name Server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.5.1.3 | ColumndhcpPoolOptNetbiosServerIpAddress | read-write | current | Specifies the IP address of the NetBIOS WINS name server. One IP address is required. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.6 | TabledhcpServerExcludedIpAddrTable | not-accessible | current | To specify IP addresses that a DHCP Server shuld not assign to DHCP clients. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.6.1 | RowdhcpServerExcludedIpAddrEntry | not-accessible | current | A conceptual row of dhcpServerExcludedIpAddrTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.6.1.1 | ColumndhcpServerExcludedIpAddrLowIp | not-accessible | current | The excluded IP address, or first IP address in an excluded address range. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.6.1.2 | ColumndhcpServerExcludedIpAddrHiIp | not-accessible | current | The last IP address in the excluded address range. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.6.1.3 | ColumndhcpServerExcludedIpAddrStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7 | TabledhcpServerLeaseBindingTable | not-accessible | current | To configure the address bindings on the DHCP server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7.1 | RowdhcpServerLeaseBindingEntry | not-accessible | current | A conceptual row of dhcpServerLeaseBindingTable. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7.1.1 | ColumndhcpServerLeaseBindingIp | not-accessible | current | The IP address of the host as recorded on the DHCP Server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7.1.2 | ColumndhcpServerLeaseBindingMac | read-only | current | The MAC address of the host as recorded on the DHCP Server. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7.1.3 | ColumndhcpServerLeaseBindingLeaseTime | read-only | current | The lease expiration date of the IP address of the host. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7.1.4 | ColumndhcpServerLeaseBindingStartTime | read-only | current | Show current system real time in sec. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.7.1.5 | ColumndhcpServerLeaseBindingStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.10.11.3.8 | ScalardhcpServerServiceStatus | read-write | current | Setting this to 1 to enable the dhcp server service. Setting this to 2 to disable the dhcp server service. |
| 1.3.6.1.4.1.259.6.10.57.1.10.16 | TableiPAddrTable | not-accessible | current | A table of iPAddrEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1 | RowiPAddrEntry | not-accessible | current | A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is … |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1.1 | ColumniPAddrIPAddress | not-accessible | current | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask is 0.0.0.0, then when the… |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1.2 | ColumniPAddrSubnetMask | not-accessible | current | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask are 0.0.0.0, then when t… |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1.3 | ColumniPAddrIfIndex | read-create | current | The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table. |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1.4 | ColumniPAddrPrimaryInterface | read-create | current | Whether this is a primary interface. |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1.5 | ColumniPAddrUnnumbered | read-only | current | Whether this is an unnumbered interface. |
| 1.3.6.1.4.1.259.6.10.57.1.10.16.1.6 | ColumniPAddrStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.11 | NodebcastStormMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.11.1 | TablebcastStormTable | not-accessible | current | Table of descriptive and status information about configuration of each switch ports(including expansion slot) in this system. |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1 | RowbcastStormEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1.1 | ColumnbcastStormIfIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1.2 | ColumnbcastStormStatus | read-write | current | Whether broadcast storm protection is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1.3 | ColumnbcastStormSampleType | read-write | current | Sample type. If this is pkt-rate(1), then bcastStormPktRate is valid. If this is octet-rate(2), then bcastStormOctetRate is valid. If this is percent(3), then … |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1.4 | ColumnbcastStormPktRate | read-write | current | Broadcast storm threshold as packets per second. |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1.5 | ColumnbcastStormOctetRate | read-write | current | Broadcast storm threshold as octets per second. |
| 1.3.6.1.4.1.259.6.10.57.1.11.1.1.6 | ColumnbcastStormPercent | read-write | current | Broadcast storm threshold as percentage of bandwidth. |
| 1.3.6.1.4.1.259.6.10.57.1.12 | NodevlanMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.12.1 | TablevlanTable | not-accessible | current | Table for VLAN configuration. |
| 1.3.6.1.4.1.259.6.10.57.1.12.1.1 | RowvlanEntry | not-accessible | current | Entry for VLAN configuration. |
| 1.3.6.1.4.1.259.6.10.57.1.12.1.1.1 | ColumnvlanIndex | not-accessible | current | Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface. |
| 1.3.6.1.4.1.259.6.10.57.1.12.1.1.2 | ColumnvlanAddressMethod | read-write | current | Method to get the IP address. |
| 1.3.6.1.4.1.259.6.10.57.1.12.2 | TablevlanPortTable | not-accessible | current | Table for port configuration in VLAN. |
| 1.3.6.1.4.1.259.6.10.57.1.12.2.1 | RowvlanPortEntry | not-accessible | current | Entry for port configuration in VLAN. |
| 1.3.6.1.4.1.259.6.10.57.1.12.2.1.1 | ColumnvlanPortIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.12.2.1.2 | ColumnvlanPortMode | read-write | current | This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. |
| 1.3.6.1.4.1.259.6.10.57.1.13 | NodepriorityMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.13.1 | ScalarprioIpPrecDscpStatus | read-write | current | Whether IP precedence or DSCP look-up is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.13.2 | TableprioIpPrecTable | not-accessible | current | Table for IP precedence priority mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.13.2.1 | RowprioIpPrecEntry | not-accessible | current | Entry for IP precendence priority mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.13.2.1.2 | ColumnprioIpPrecPort | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.13.2.1.3 | ColumnprioIpPrecValue | not-accessible | current | Precedence value for this entry. |
| 1.3.6.1.4.1.259.6.10.57.1.13.2.1.4 | ColumnprioIpPrecCos | read-write | current | Class of service for this entry. |
| 1.3.6.1.4.1.259.6.10.57.1.13.3 | ScalarprioIpPrecRestoreDefault | read-write | current | This object is to restore IP Precedence settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When … |
| 1.3.6.1.4.1.259.6.10.57.1.13.4 | TableprioIpDscpTable | not-accessible | current | Table for IP DSCP priority mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.13.4.1 | RowprioIpDscpEntry | not-accessible | current | Entry for IP DSCP priority mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.13.4.1.1 | ColumnprioIpDscpPort | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.259.6.10.57.1.13.4.1.2 | ColumnprioIpDscpValue | not-accessible | current | DSCP value for this entry. |
| 1.3.6.1.4.1.259.6.10.57.1.13.4.1.3 | ColumnprioIpDscpCos | read-write | current | Class of service for this entry. |
| 1.3.6.1.4.1.259.6.10.57.1.13.5 | ScalarprioIpDscpRestoreDefault | read-write | current | This object is to restore IP DSCP settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, … |
| 1.3.6.1.4.1.259.6.10.57.1.13.6 | ScalarprioIpPortEnableStatus | read-write | current | Whether IP Port priority look-up is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.13.7 | TableprioIpPortTable | not-accessible | current | Table for IP port priority mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.13.7.1 | RowprioIpPortEntry | not-accessible | current | Entry for IP port priority mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.13.7.1.1 | ColumnprioIpPortPhysPort | not-accessible | current | The port and the trunk (excluding trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface … |
| 1.3.6.1.4.1.259.6.10.57.1.13.7.1.2 | ColumnprioIpPortValue | not-accessible | current | IP port for this value. |
| 1.3.6.1.4.1.259.6.10.57.1.13.7.1.3 | ColumnprioIpPortCos | read-create | current | Class of service for this entry. |
| 1.3.6.1.4.1.259.6.10.57.1.13.7.1.4 | ColumnprioIpPortStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.13.8 | NodeprioCopy | |||
| 1.3.6.1.4.1.259.6.10.57.1.13.8.1 | ScalarprioCopyIpPrec | read-write | current | Action to copy IP Precedence settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-… |
| 1.3.6.1.4.1.259.6.10.57.1.13.8.2 | ScalarprioCopyIpDscp | read-write | current | Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (b… |
| 1.3.6.1.4.1.259.6.10.57.1.13.8.3 | ScalarprioCopyIpPort | read-write | current | Action to copy IP Port settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (b… |
| 1.3.6.1.4.1.259.6.10.57.1.13.10 | ScalarprioQueueMode | read-write | current | The global status for the prioQueue. wrr(1),strict(2) |
| 1.3.6.1.4.1.259.6.10.57.1.13.12 | TableprioWrrPortTable | not-accessible | current | Table for per port weighted round robin (WRR). |
| 1.3.6.1.4.1.259.6.10.57.1.13.12.1 | RowprioWrrPortEntry | not-accessible | current | Entry for per port weighted round robin (WRR). |
| 1.3.6.1.4.1.259.6.10.57.1.13.12.1.1 | ColumnprioWrrPortIfIndex | not-accessible | current | The port interface of the prioWrrPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value … |
| 1.3.6.1.4.1.259.6.10.57.1.13.12.1.2 | ColumnprioWrrPortTrafficClass | not-accessible | current | Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTraf… |
| 1.3.6.1.4.1.259.6.10.57.1.13.12.1.3 | ColumnprioWrrPortWeight | read-write | current | Weight for this entry. |
| 1.3.6.1.4.1.259.6.10.57.1.14 | NodetrapDestMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.14.1 | TabletrapDestTable | not-accessible | current | A list of trap destination entries. |
| 1.3.6.1.4.1.259.6.10.57.1.14.1.1 | RowtrapDestEntry | not-accessible | current | This entry includes a destination IP address to which to send traps for this community. |
| 1.3.6.1.4.1.259.6.10.57.1.14.1.1.1 | ColumntrapDestAddress | not-accessible | current | The address to send traps. |
| 1.3.6.1.4.1.259.6.10.57.1.14.1.1.2 | ColumntrapDestCommunity | read-create | current | A community to which this destination address belongs. |
| 1.3.6.1.4.1.259.6.10.57.1.14.1.1.3 | ColumntrapDestStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.14.1.1.4 | ColumntrapDestVersion | read-create | current | This variables represent the version of the Trap we wish to send to trap Receiver. If the value is 1, mean we wish to send Version 1 trap. If the value is 2, m… |
| 1.3.6.1.4.1.259.6.10.57.1.14.1.1.5 | ColumntrapDestUdpPort | read-create | current | Determines the UDP port number of the trap that is to be sent to the trap Receiver. |
| 1.3.6.1.4.1.259.6.10.57.1.16 | NodeqosMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.16.1 | NoderateLimitMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2 | TablerateLimitPortTable | not-accessible | current | Table for rate limit of each port. |
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2.1 | RowrateLimitPortEntry | not-accessible | current | Entry for rate limit of each port. |
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2.1.1 | ColumnrlPortIndex | not-accessible | current | The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface … |
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2.1.2 | ColumnrlPortInputLimit | read-write | current | Value of the input rate limit. Its unit is megabits per second. For a 100 Mb/s port, the range is 1 to 100. For a 1000 Mb/s port, the range is 1 to 1000. |
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2.1.3 | ColumnrlPortOutputLimit | read-write | current | Value of the output rate limit. Its unit is megabits per second. For a 100 Mb/s port, the range is 1 to 100. For a 1000 Mb/s port, the range is 1 to 1000. |
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2.1.6 | ColumnrlPortInputStatus | read-write | current | Whether input rate limit is enabled for this port. |
| 1.3.6.1.4.1.259.6.10.57.1.16.1.2.1.7 | ColumnrlPortOutputStatus | read-write | current | Whether output rate limit is enabled for this port. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2 | NodemarkerMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1 | TablemarkerTable | not-accessible | current | The marker table. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1 | RowmarkerEntry | not-accessible | current | Entry for marker table. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.1 | ColumnmarkerIfIndex | not-accessible | current | The interface index of the marker table. The interface identified by a particular value of this index is the same interface as identified by the same value of … |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.2 | ColumnmarkerAclName | not-accessible | current | The name of an ACL. Within a feature the name is unique used to identifies the list to which the entry belongs in the device. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.3 | ColumnmarkerActionBitList | read-create | current | The marker action bit list, in right to left order. for example: 0x3(11 in binary) means dscp(0) and precedence(1) 0x4(100 in binary) means priority(2) |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.4 | ColumnmarkerDscp | read-create | current | The Dscp value of the marker entry. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.5 | ColumnmarkerPrecedence | read-create | current | The precedence value of the marker entry. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.6 | ColumnmarkerPriority | read-create | current | The priority value of the marker entry. |
| 1.3.6.1.4.1.259.6.10.57.1.16.2.1.1.7 | ColumnmarkerStatus | read-create | current | The status of this marker conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist… |
| 1.3.6.1.4.1.259.6.10.57.1.16.3 | NodecosMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.16.3.1 | TableprioAclToCosMappingTable | not-accessible | current | Table for Acl to Cos Mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.16.3.1.1 | RowprioAclToCosMappingEntry | not-accessible | current | Entry for Acl to Cos Mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.16.3.1.1.1 | ColumnprioAclToCosMappingIfIndex | not-accessible | current | The port interface of the prioAclToCosMappingEntry. The interface identified by a particular value of this index is the same interface as identified by the sam… |
| 1.3.6.1.4.1.259.6.10.57.1.16.3.1.1.2 | ColumnprioAclToCosMappingAclName | not-accessible | current | The name of an IP ACL. Within a feature the name is unique used to identifies the list to which the entry belongs in the device. |
| 1.3.6.1.4.1.259.6.10.57.1.16.3.1.1.3 | ColumnprioAclToCosMappingCosValue | read-create | current | Cos value of the prioAclToCosMappingTable. |
| 1.3.6.1.4.1.259.6.10.57.1.16.3.1.1.4 | ColumnprioAclToCosMappingStatus | read-create | current | The status of this acl to cos mapping conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry m… |
| 1.3.6.1.4.1.259.6.10.57.1.17 | NodesecurityMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.2 | NodeportSecurityMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.2.1 | TableportSecPortTable | not-accessible | current | The Port Security(MAC bindind) Table |
| 1.3.6.1.4.1.259.6.10.57.1.17.2.1.1 | RowportSecPortEntry | not-accessible | current | The entry of portSecPortTable |
| 1.3.6.1.4.1.259.6.10.57.1.17.2.1.1.1 | ColumnportSecPortIndex | not-accessible | current | The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.259.6.10.57.1.17.2.1.1.2 | ColumnportSecPortStatus | read-write | current | Set enabled(1) to enable port security and set disabled(2) to disable port security. |
| 1.3.6.1.4.1.259.6.10.57.1.17.2.1.1.3 | ColumnportSecAction | read-write | current | The corresponding actions that will take place when a port is under intruded, when this variable is set to none(1), no action will perform, when this variable … |
| 1.3.6.1.4.1.259.6.10.57.1.17.2.1.1.4 | ColumnportSecMaxMacCount | read-write | current | The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will di… |
| 1.3.6.1.4.1.259.6.10.57.1.17.4 | NoderadiusMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.4.1 | ScalarradiusServerAddress | read-write | current | IP address of RADIUS server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.4.2 | ScalarradiusServerPortNumber | read-write | current | IP port number of RADIUS server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.4.3 | ScalarradiusServerKey | read-write | current | Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string. |
| 1.3.6.1.4.1.259.6.10.57.1.17.4.4 | ScalarradiusServerRetransmit | read-write | current | Maximum number of retransmissions for RADIUS. |
| 1.3.6.1.4.1.259.6.10.57.1.17.4.5 | ScalarradiusServerTimeout | read-write | current | Timeout for RADIUS. |
| 1.3.6.1.4.1.259.6.10.57.1.17.5 | NodetacacsMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.5.1 | ScalartacacsServerAddress | read-write | current | IP address of TACACS server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.5.2 | ScalartacacsServerPortNumber | read-write | current | IP port number of TACACS server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.5.3 | ScalartacacsServerKey | read-write | current | Key for TACACS. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6 | NodesshMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.6.1 | ScalarsshServerStatus | read-write | current | The status of Secure Shell Server, set this value to 1 to enable SSH server, set this value to 2 to disable the SSH server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.2 | ScalarsshServerMajorVersion | read-only | current | The major version of the SSH Server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.3 | ScalarsshServerMinorVersion | read-only | current | The minor version of the SSH Server. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.4 | ScalarsshTimeout | read-write | current | The time interval that the router waits for the SSH client to respond. The range is 1-120. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.5 | ScalarsshAuthRetries | read-write | current | The number of attempts after which the interface is reset. The range is 1-5. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6 | TablesshConnInfoTable | not-accessible | current | The table for Secure Shell Connection. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1 | RowsshConnInfoEntry | not-accessible | current | The conceptual row for sshConnInfoTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.1 | ColumnsshConnID | not-accessible | current | The connection ID of the Secure Shell Connection. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.2 | ColumnsshConnMajorVersion | read-only | current | The SSH major version. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.3 | ColumnsshConnMinorVersion | read-only | current | The SSH minor version. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.5 | ColumnsshConnStatus | read-only | current | The SSH connection State. negotiationStart(1) mean the SSH is in its negotiation start state, authenticationStart(2) mean the SSH is in authentication start st… |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.6 | ColumnsshConnUserName | read-only | current | The user name of the connection. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.7 | ColumnsshDisconnect | read-write | current | Set the variables to disconnect to disconnect the connection, when read, this variables always return noDisconnect(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.6.1.8 | ColumnsshConnEncryptionTypeStr | read-only | current | The encryption type of the SSH. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.7 | ScalarsshKeySize | read-write | current | The SSH server key size. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.8 | ScalarsshRsaHostKey1 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.9 | ScalarsshRsaHostKey2 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.10 | ScalarsshRsaHostKey3 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.11 | ScalarsshRsaHostKey4 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.12 | ScalarsshRsaHostKey5 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.13 | ScalarsshRsaHostKey6 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.14 | ScalarsshRsaHostKey7 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.15 | ScalarsshRsaHostKey8 | read-only | current | The total length of RSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshRsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.16 | ScalarsshDsaHostKey1 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.17 | ScalarsshDsaHostKey2 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.18 | ScalarsshDsaHostKey3 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.19 | ScalarsshDsaHostKey4 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.20 | ScalarsshDsaHostKey5 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.21 | ScalarsshDsaHostKey6 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.22 | ScalarsshDsaHostKey7 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.23 | ScalarsshDsaHostKey8 | read-only | current | The total length of DSA host key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshDsaHostKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.24 | ScalarsshHostKeyGenAction | read-write | current | This variable is for host key generating. For the set behavior: set it to genRsaKey(2) to generate the RSA host key, genDsaKey(3) to generate the DSA host key,… |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.25 | ScalarsshHostKeyGenStatus | read-only | current | The result of the last KeyGen status. if no Key gen action has been perform you will get unknown(1) status. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.26 | ScalarsshHostKeySaveAction | read-write | current | To save host key from memory to flash. For the set behavior: set it to save(2) to perform the save operation. For the get behavior: you will get save(1) when t… |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.27 | ScalarsshHostKeySaveStatus | read-only | current | The result of the last savekey status. if no save action has been perform you will get unknown(1) status. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.28 | ScalarsshHostKeyDelAction | read-write | current | To delete the host key. For the set behavior: set it to delRsaKey(2) to delete the RSA host key, delDsaKey(3) to delete the DSA host key, or delBothKeys(4) to … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29 | TablesshUserTable | not-accessible | current | The conceptual table of all of sshUserEntry |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1 | RowsshUserEntry | not-accessible | current | The conceptual row for sshUserTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.1 | ColumnsshUserName | not-accessible | current | User Name. |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.2 | ColumnsshUserRsaKey1 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.3 | ColumnsshUserRsaKey2 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.4 | ColumnsshUserRsaKey3 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.5 | ColumnsshUserRsaKey4 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.6 | ColumnsshUserRsaKey5 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.7 | ColumnsshUserRsaKey6 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.8 | ColumnsshUserRsaKey7 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.9 | ColumnsshUserRsaKey8 | read-only | current | The total length of RSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.10 | ColumnsshUserDsaKey1 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.11 | ColumnsshUserDsaKey2 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.12 | ColumnsshUserDsaKey3 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.13 | ColumnsshUserDsaKey4 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.14 | ColumnsshUserDsaKey5 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.15 | ColumnsshUserDsaKey6 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.16 | ColumnsshUserDsaKey7 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.17 | ColumnsshUserDsaKey8 | read-only | current | The total length of DSA user key is 1024 characters, it is divided into 8 parts and store in 8 separated mib variables as below: sshUserRsaKey1: part 1 of the … |
| 1.3.6.1.4.1.259.6.10.57.1.17.6.29.1.18 | ColumnsshUserKeyDelAction | read-write | current | To delete the user key. For the set behavior: set it to delRsaKey(2) to delete the RSA user key, delDsaKey(3) to delete the DSA user key, or delBothKeys(4) to … |
| 1.3.6.1.4.1.259.6.10.57.1.17.7 | NodeaclMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1 | TableaclIpAceTable | not-accessible | current | The conceptual table of all of aclIpAceEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1 | RowaclIpAceEntry | not-accessible | current | The conceptual row for aclIpAceTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.1 | ColumnaclIpAceName | not-accessible | current | The name of an ACL. Within a feature a unique name is used to identify the list to which the entry belongs in the device. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.2 | ColumnaclIpAceIndex | not-accessible | current | The unique index of an ACE within an ACL. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.3 | ColumnaclIpAcePrecedence | read-only | current | Specifies the IP precedence value to be matched against. This object cannot not be configured when the status of the entry, aclIpAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.4 | ColumnaclIpAceAction | read-create | current | Indicates the action to be taken if a packet matches this ACE. This object cannot not be configured when the status of the entry, aclIpAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.5 | ColumnaclIpAceSourceIpAddr | read-create | current | The specified source IP address. The packet's source address is AND-ed with the value of aclIpAceSourceIpAddrBitmask and then compared against the value of thi… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.6 | ColumnaclIpAceSourceIpAddrBitmask | read-create | current | The specified source IP address mask. The packet's destination address is AND-ed with the value of aclIpAceSourceIpAddr and then compared against the value of … |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.7 | ColumnaclIpAceDestIpAddr | read-create | current | The specified destination IP address. The packet's destination address is AND-ed with the value of aclIpAceDestIpAddrBitmask and then compared against the valu… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.8 | ColumnaclIpAceDestIpAddrBitmask | read-create | current | The specified destination IP address mask. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.9 | ColumnaclIpAceProtocol | read-create | current | The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value value of 0 matches every IP packet. The… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.10 | ColumnaclIpAcePrec | read-create | current | Specifies the IP precedence value to be matched against. This object cannot be configured when the status of the entry, aclIpAceStatus, is active(1). The value… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.11 | ColumnaclIpAceTos | read-create | current | Specifies the IP ToS facility value to be matched against. This object cannot be configured when the status of the entry, aclIpAceStatus, is active(1). The val… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.12 | ColumnaclIpAceDscp | read-create | current | Specifies the DSCP value to be matched against. This object cannot be configured when the status of the entry, aclIpAceStatus, is active(1). The value of this … |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.13 | ColumnaclIpAceSourcePortOp | read-create | current | Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the so… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.14 | ColumnaclIpAceMinSourcePort | read-create | current | If the aclIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.15 | ColumnaclIpAceMaxSourcePort | read-create | current | If the aclIpAceSourcePortOp is range(3), this indicates the upper bound of the TCP/UDP port number value range. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.16 | ColumnaclIpAceSourcePortBitmask | read-create | current | If the aclIpAceSourcePortOp is equal(2), this indicates the bitmask of the aclIpAceMinSourcePort. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.17 | ColumnaclIpAceDestPortOp | read-create | current | Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made w… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.18 | ColumnaclIpAceMinDestPort | read-create | current | If the aclIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.19 | ColumnaclIpAceMaxDestPort | read-create | current | If the aclIpAceDestPortOp is range(3), this indicates the upper bound of the TCP/UDP port number value range. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.20 | ColumnaclIpAceDestPortBitmask | read-create | current | If the aclIpAceDestPortOp is equal(2), this indicates the bitmask of the aclIpAceMinDestPort. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.21 | ColumnaclIpAceControlCode | read-create | current | Indicates how the control flags of TCP packets are to be compared. aceIpControlCode is AND-ed with aceIpControlCodeBitmask. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.22 | ColumnaclIpAceControlCodeBitmask | read-create | current | Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.1.1.23 | ColumnaclIpAceStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2 | TableaclMacAceTable | not-accessible | current | The conceptual table of all of aclMacAceEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1 | RowaclMacAceEntry | not-accessible | current | The conceptual row for aclMacAceTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.1 | ColumnaclMacAceName | not-accessible | current | The name of an ACL. Within a feature, a unique name is used to identify the list to which the entry belongs in the device. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.2 | ColumnaclMacAceIndex | not-accessible | current | The unique index of an ACE within an ACL. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.3 | ColumnaclMacAcePrecedence | read-only | current | Specifies the entry's precedence. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.4 | ColumnaclMacAceAction | read-create | current | Indicates the action to be taken if a packet matches this ACE. This object cannot be configured when the status of the entry, aclMacAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.5 | ColumnaclMacAcePktformat | read-create | current | Used to check the packet format of the packets. This object cannot be configured when the status of the entry, aclMacAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.6 | ColumnaclMacAceSourceMacAddr | read-create | current | Indicates the 48-bit destination MAC address. The specified source MAC of the packet The packet's source MAC address is AND-ed with the value of aceMacSourceMa… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.7 | ColumnaclMacAceSourceMacAddrBitmask | read-create | current | The specified source MAC address mask. This object cannot be configured when the status of the entry, aclMacAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.8 | ColumnaclMacAceDestMacAddr | read-create | current | Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of ace… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.9 | ColumnaclMacAceDestMacAddrBitmask | read-create | current | The specified destination MAC address mask. This object cannot be configured when the status of the entry, aclMacAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.10 | ColumnaclMacAceVidOp | read-create | current | Indicates how a packet's vid is to be compared. This object cannot be configured when the status of the entry, aclMacAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.11 | ColumnaclMacAceMinVid | read-create | current | Indicates the lower bound of the vid value range if the aclMacAceVidOp is range(3). This object cannot be configured when the status of the entry, aclMacAceSta… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.12 | ColumnaclMacAceVidBitmask | read-create | current | The bitmask of vid if the aclMacAceVidOp is equal, default value is 0xfff. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.13 | ColumnaclMacAceMaxVid | read-create | current | Indicates the upper bound of the vid value range if the aclMacAceVidOp is range(3). This object cannot be configured when the status of the entry, aclMacAceSta… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.14 | ColumnaclMacAceEtherTypeOp | read-create | current | Indicates how a packet's ethertype is to be compared. This object cannot be configured when the status of the entry, aclMacAceStatus, is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.15 | ColumnaclMacAceEtherTypeBitmask | read-create | current | The bitmask of vid if the aclMacAceVidOp is equal(2) , default value is 0xFFFF. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.16 | ColumnaclMacAceMinEtherType | read-create | current | Indicates the lower bound of the vid value range if the aclMacAceEtherTypeOp is range(3). This object cannot be configured when the status of the entry, aclMac… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.17 | ColumnaclMacAceMaxEtherType | read-create | current | Indicates the upper bound of the vid value range if the aclMacAceEtherTypeOp is range(3). This object cannot be configured when the status of the entry, aclMac… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.2.1.18 | ColumnaclMacAceStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3 | TableaclAclGroupTable | not-accessible | current | The conceptual table of aclAclGroupEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3.1 | RowaclAclGroupEntry | not-accessible | current | The conceptual row for aclAclGroupTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3.1.1 | ColumnaclAclGroupIfIndex | not-accessible | current | The interface number specifying the ACL binding to. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3.1.2 | ColumnaclAclGroupIngressIpAcl | read-write | current | Specifies the ingress IP ACL(standard or extended) binding to the interface. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3.1.3 | ColumnaclAclGroupEgressIpAcl | read-write | current | Specifies the egress IP ACL(standard or extended) binding to the interface. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3.1.4 | ColumnaclAclGroupIngressMacAcl | read-write | current | Specifies the ingress MAC ACL binding to the interface. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.3.1.5 | ColumnaclAclGroupEgressMacAcl | read-write | current | Specifies the egress MAC ACL binding to the interface. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4 | TableaclIngressIpMaskTable | not-accessible | current | The conceptual table of aclIngressIpMaskEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1 | RowaclIngressIpMaskEntry | not-accessible | current | The conceptual row for aclIngressIpMaskTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.1 | ColumnaclIngressIpMaskIndex | not-accessible | current | Indicates the bitmask of the source IP address. The relative bitmask must be created before the ACE binds to the interface. This object cannot be configured wh… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.2 | ColumnaclIngressIpMaskPrecedence | read-only | current | Indicates whether to check the IP precedence against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress directi… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.3 | ColumnaclIngressIpMaskIsEnableTos | read-create | current | Indicates whether to check the IP ToS facility against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress direc… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.4 | ColumnaclIngressIpMaskIsEnableDscp | read-create | current | Indicates whether to check the IP DSCP against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direction. Th… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.5 | ColumnaclIngressIpMaskIsEnablePrecedence | read-create | current | Indicates whether to check the IP precednce against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress directio… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.6 | ColumnaclIngressIpMaskIsEnableProtocol | read-create | current | Indicates whether to check the IP protocol against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direction… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.7 | ColumnaclIngressIpMaskSourceIpAddrBitmask | read-create | current | Indicates the source IP bitmask to check against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress direction. … |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.8 | ColumnaclIngressIpMaskDestIpAddrBitmask | read-create | current | Indicates the destination IP bitmask to check against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress direct… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.9 | ColumnaclIngressIpMaskSourcePortBitmask | read-create | current | Indicates the source port bitmask to check against the TCP/UDP packets, The relative bitmask must be created before the ACE binds to the interface in ingress d… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.10 | ColumnaclIngressIpMaskDestPortBitmask | read-create | current | Indicates the destination port bitmask to check against the TCP/UDP packets, The relative bitmask must be created before the ACE binds to the interface in ingr… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.11 | ColumnaclIngressIpMaskControlCodeBitmask | read-create | current | Indicates the control code bitmask to check against the TCP packets, The relative bitmask must be created before the ACE binds to the interface in ingress dire… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.4.1.12 | ColumnaclIngressIpMaskStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5 | TableaclEgressIpMaskTable | not-accessible | current | The conceptual table of aclEgressIpMaskEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1 | RowaclEgressIpMaskEntry | not-accessible | current | The conceptual row for aclEgressIpMaskTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.1 | ColumnaclEgressIpMaskIndex | not-accessible | current | The index of a mask entry within a mask table. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.2 | ColumnaclEgressIpMaskPrecedence | read-only | current | The created precedence of an mask entry within the mask table. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.3 | ColumnaclEgressIpMaskIsEnableTos | read-create | current | Indicates whether to check the IP ToS facility against the packets. The relative bitmask must be created before the ACE binds to the interface in egress direct… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.4 | ColumnaclEgressIpMaskIsEnableDscp | read-create | current | Indicates whether to check the IP DSCP against the packets. The relative bitmask must be created before the ACE binds to the interface in egress direction. Thi… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.5 | ColumnaclEgressIpMaskIsEnablePrecedence | read-create | current | Indicates whether to check the IP precedence against the packets. The relative bitmask must be created before the ACE binds to the interface in egress directio… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.6 | ColumnaclEgressIpMaskIsEnableProtocol | read-create | current | Indicates whether to check the IP protocol against the packets. The relative bitmask must be created before the ACE binds to the interface in egress direction.… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.7 | ColumnaclEgressIpMaskSourceIpAddrBitmask | read-create | current | Indicates the source IP bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in egress direction. T… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.8 | ColumnaclEgressIpMaskDestIpAddrBitmask | read-create | current | Indicates the destination IP bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in egress directi… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.9 | ColumnaclEgressIpMaskSourcePortBitmask | read-create | current | Indicates the source port bitmask to check against the TCP/UDP packets. The relative bitmask must be created before the ACE binds to the interface in egress di… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.10 | ColumnaclEgressIpMaskDestPortBitmask | read-create | current | Indicates the destination port bitmask to check against the TCP/UDP packets. The relative bitmask must be created before the ACE binds to the interface in egre… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.11 | ColumnaclEgressIpMaskControlCodeBitmask | read-create | current | Indicates the control code bitmask to check against the TCP packets. The relative bitmask must be created before the ACE binds to the interface in egress direc… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.5.1.12 | ColumnaclEgressIpMaskStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6 | TableaclIngressMacMaskTable | not-accessible | current | The conceptual table of aclIngressMacMaskEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1 | RowaclIngressMacMaskEntry | not-accessible | current | The conceptual row for aclIngressMacMaskTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.1 | ColumnaclIngressMacMaskIndex | not-accessible | current | The index of an mask entry within an ingress mask table. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.2 | ColumnaclIngressMacMaskPrecedence | read-only | current | The created order of an mask entry within an ingress mask table. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.3 | ColumnaclIngressMacMaskSourceMacAddrBitmask | read-create | current | Indicates the source MAC bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direction.… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.4 | ColumnaclIngressMacMaskDestMacAddrBitmask | read-create | current | Indicates the destination MAC bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direc… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.5 | ColumnaclIngressMacMaskVidBitmask | read-create | current | Indicates the vid bitmask to check against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress direction. This o… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.6 | ColumnaclIngressMacMaskEtherTypeBitmask | read-create | current | Indicates the ethertype bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direction. … |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.7 | ColumnaclIngressMacMaskIsEnablePktformat | read-create | current | Indicates whether to check the packet format against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress directi… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.6.1.8 | ColumnaclIngressMacMaskStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7 | TableaclEgressMacMaskTable | not-accessible | current | The conceptual table of aclEgressMacMaskEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1 | RowaclEgressMacMaskEntry | not-accessible | current | The conceptual row for aclEgressMacMaskTable. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.1 | ColumnaclEgressMacMaskIndex | not-accessible | current | The index of a mask entry within an egress mask table. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.2 | ColumnaclEgressMacMaskPrecedence | read-only | current | The created precedence of a mask entry within an egress mask table. |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.3 | ColumnaclEgressMacMaskSourceMacAddrBitmask | read-create | current | Indicates the source MAC bitmask to check against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress direction.… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.4 | ColumnaclEgressMacMaskDestMacAddrBitmask | read-create | current | Indicates the destination MAC bitmask to check against the packets, The relative bitmask must be created before the ACE binds to the interface in ingress direc… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.5 | ColumnaclEgressMacMaskVidBitmask | read-create | current | Indicates the vid bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direction. This o… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.6 | ColumnaclEgressMacMaskEtherTypeBitmask | read-create | current | Indicates the ethertype bitmask to check against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress direction. … |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.7 | ColumnaclEgressMacMaskIsEnablePktformat | read-create | current | Indicates whether to check the packet format against the packets. The relative bitmask must be created before the ACE binds to the interface in ingress directi… |
| 1.3.6.1.4.1.259.6.10.57.1.17.7.7.1.8 | ColumnaclEgressMacMaskStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.17.9 | NodeipFilterMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.17.9.1 | TableipFilterSnmpTable | not-accessible | current | A list of IP address entries. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.1.1 | RowipFilterSnmpEntry | not-accessible | current | This entry includes an IP address range which the system will allow them to connect to this device through SNMP. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.1.1.1 | ColumnipFilterSnmpStartAddress | not-accessible | current | The start-ip-address. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.1.1.2 | ColumnipFilterSnmpEndAddress | read-create | current | The end-ip-address. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.1.1.3 | ColumnipFilterSnmpStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.2 | TableipFilterHTTPTable | not-accessible | current | A list of IP address entries. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.2.1 | RowipFilterHTTPEntry | not-accessible | current | This entry includes an IP address range which the system will allow them to connect to this device through SNMP. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.2.1.1 | ColumnipFilterHTTPStartAddress | not-accessible | current | The start-ip-address. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.2.1.2 | ColumnipFilterHTTPEndAddress | read-create | current | The end-ip-address. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.2.1.3 | ColumnipFilterHTTPStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.3 | TableipFilterTelnetTable | not-accessible | current | A list of IP address entries. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.3.1 | RowipFilterTelnetEntry | not-accessible | current | This entry includes an IP address range which the system will allow them to connect to this device through SNMP. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.3.1.1 | ColumnipFilterTelnetStartAddress | not-accessible | current | The start-ip-address. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.3.1.2 | ColumnipFilterTelnetEndAddress | read-create | current | The end-ip-address. |
| 1.3.6.1.4.1.259.6.10.57.1.17.9.3.1.3 | ColumnipFilterTelnetStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.18 | Nodelayer3Mgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.1 | NodearpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.1.1 | ScalararpCacheDeleteAll | read-write | current | To delete all dynamic entries in the ARP cache, write this variable to delete(1). Writing this variable to noDelete(2) has no effect on the device. When read, … |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.2 | ScalararpCacheTimeout | read-write | current | The timeout is provided for entries in the ARP Cache. It's for dynamic mapping only. Static mapping by creating a entry that associates a logical address with … |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.3 | NodearpTrafficStatistics | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.1.3.1 | ScalararpStatSendRequestPackets | read-only | current | The number of ARP Request packets sent by the ARP process. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.3.2 | ScalararpStatRcvRequestPackets | read-only | current | The number of ARP Request packets received by the ARP process. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.3.3 | ScalararpStatSendReplyPackets | read-only | current | The number of ARP Reply packets sent by the ARP process. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.3.4 | ScalararpStatRcvReplyPackets | read-only | current | The number of ARP Reply packets received by the ARP process. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.4 | TablearpProxyArpTable | not-accessible | current | A list of Proxy ARP status. This table has entries for all static VLANs. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.4.1 | RowarpProxyArpEntry | not-accessible | current | An entry in the table, containing information about Proxy ARP configuration. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.4.1.1 | ColumnarpProxyArpIfIndex | not-accessible | current | This is defined as a VLAN interface. A routing interface is a VLAN binds a IP subnet. |
| 1.3.6.1.4.1.259.6.10.57.1.18.1.4.1.2 | ColumnarpProxyArpStatus | read-write | current | Enable or Disable Proxy ARP process on an interface |
| 1.3.6.1.4.1.259.6.10.57.1.18.2 | NoderipMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.2.1 | NoderipTimers | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.2.1.1 | ScalarripUpdateTime | read-write | current | The update time in seconds controls the advertising of regular update messages. The real working model, while using this timer, the time should be offset by a … |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.1.2 | ScalarripTimeoutTime | read-only | current | The timeout timer in seconds governs the validity of a route. It is initialized when a route is established, and any time an update message is received for the… |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.1.3 | ScalarripGarbageCollectionTime | read-only | current | When the information about a route becomes invalid, the system should not immediately purge that route from its table. Instead, it continues to advertise the r… |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.2 | ScalarripRoutingProcessStatus | read-write | current | Enable or Disable RIP routing process on a system. |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.3 | ScalarripRouterVersion | read-write | current | To specify a RIP version used globally by the rourter. |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.4 | TableripInstabilityPreventingTable | not-accessible | current | A list of RIP instability preventing status |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.4.1 | RowripInstabilityPreventingEntry | not-accessible | current | An entry in the table, containing information about RIP instability preventing configuration. The ifIndex index is a VLAN's ifIndex |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.4.1.1 | ColumnripVlanIndex | not-accessible | current | This is defined as a VLAN interface. A routing interface is a VLAN binds a IP subnet. |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.4.1.2 | ColumnripSplitHorizonStatus | read-write | current | Enable or Disable RIP Poison Reverse on an interface |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.5 | ScalarripStatisticsReset | read-write | current | Write it to reset(1), the following objects in RFC 1724 should be reset: 1. Global Counters: 'rip2GlobalRouteChanges', 'rip2GlobalQueries'. 2. Interface Status… |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.6 | TableripNetworkAddrTable | not-accessible | current | |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.6.1 | RowripNetworkAddrEntry | not-accessible | current | |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.6.1.1 | ColumnripNetworkAddrAddress | not-accessible | current | The RIP Network address. |
| 1.3.6.1.4.1.259.6.10.57.1.18.2.6.1.2 | ColumnripNetworkAddrStatus | read-create | current | Set this variable to create or destroy a RIP network address. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3 | NodeospfMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1 | NodeospfSystemGroup | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.1 | ScalarospfRouterIdType | read-only | current | Set router ID automatically or manually. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.2 | ScalarospfRfc1583CompatibleState | read-write | current | Enable or disable rfc1583 compatibility. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.3 | ScalarospfAutoCost | read-write | current | Set the reference bandwith of auto cost, the unit is Mbps. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.4 | ScalarospfOriginateDefaultRoute | read-write | current | Enable or disable ASBR to generate a default external route into an OSPF domain if the default route already exists. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.5 | ScalarospfAdvertiseDefaultRoute | read-write | current | If enabled, always advertises the default route regardless of whether the default route exists. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.6 | ScalarospfExternalMetricType | read-write | current | External link type associated with the default route advertised into the OSPF routing domain. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.7 | ScalarospfDefaultExternalMetric | read-write | current | Metric used for generating the default route. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.8 | ScalarospfSpfHoldTime | read-write | current | Sets the hold time between two consecutive SPF calculations. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.9 | ScalarospfSpfDelayTime | read-write | current | Sets the delay time to calculate SPF Delay time, in seconds, between when OSPF receives a topology change and when it starts an SPF calculation. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.1.10 | ScalarospfAreaNumber | read-only | current | Records the OSPF area numbers. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.2 | TableospfNssaTable | not-accessible | current | A conceptually table for ospfNssaEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.2.1 | RowospfNssaEntry | not-accessible | current | A conceptually row for ospfNssaTable. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.2.1.1 | ColumnospfNssaAreaId | not-accessible | current | The 32-bit identifier for the NSSA. On creation, this can be derived from the instance. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.2.1.2 | ColumnospfNssaRedistributeStatus | read-create | current | Enabled or disabled to import routes only into the normal areas, but not into the NSSA area. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.2.1.3 | ColumnospfNssaOriginateDefaultInfoStatus | read-create | current | Enable or disable to generate a Type 7 default into the NSSA area. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.2.1.4 | ColumnospfNssaStatus | read-create | current | The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. The status column has six defined values: … |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.3 | TableospfRedistributeTable | not-accessible | current | The conceptual table of all of ospfRedistributeEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.3.1 | RowospfRedistributeEntry | not-accessible | current | The conceptual row for ospfRedistributeTable. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.3.1.1 | ColumnospfRedistributeProtocol | not-accessible | current | Protocol ID. Static is not supported now. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.3.1.2 | ColumnospfRedistributeMetricType | read-create | current | Metric type. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.3.1.3 | ColumnospfRedistributeMetric | read-create | current | Metric value. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.3.1.4 | ColumnospfRedistributeStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.4 | TableospfSummaryAddressTable | not-accessible | current | The conceptual table of all of ospfSummaryAddressEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.4.1 | RowospfSummaryAddressEntry | not-accessible | current | The conceptual row for ospfSummaryAddressTable. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.4.1.1 | ColumnospfSummaryAddress | not-accessible | current | Summary address. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.4.1.2 | ColumnospfSummaryMask | not-accessible | current | Summary mask. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.4.1.3 | ColumnospfSummaryStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.5 | TableospfNetworkAreaAddressTable | not-accessible | current | The conceptual table of all of ospfNetworkAreaAddressEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.5.1 | RowospfNetworkAreaAddressEntry | not-accessible | current | The conceptual row for ospfNetworkAreaAddressTable. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.5.1.1 | ColumnospfNetworkAareaAddress | not-accessible | current | NetworkArea address. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.5.1.2 | ColumnospfNetworkAreaMask | not-accessible | current | NetworkArea mask. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.5.1.3 | ColumnospfNetworkAreaAreaId | read-create | current | NetworkArea area ID. |
| 1.3.6.1.4.1.259.6.10.57.1.18.3.5.1.4 | ColumnospfNetworkAreaStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4 | NodedvmrpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.4.1 | NodedvmrpScalar | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.4.1.1 | ScalardvmrpVersionString | read-only | current | The router's DVMRP version information. Similar to sysDescr in MIB-II, this is a free-form field which can be used to display vendor-specific information. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.1.3 | ScalardvmrpNumRoutes | read-only | current | The number of entries in the routing table. This can be used to monitor the routing table size. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.1.4 | ScalardvmrpReachableRoutes | read-only | current | The number of entries in the routing table with non infinite metrics. This can be used to detect network partitions by observing the ratio of reachable routes … |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2 | TabledvmrpInterfaceTable | not-accessible | current | The (conceptual) table listing the router's multicast- capable interfaces. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1 | RowdvmrpInterfaceEntry | not-accessible | current | An entry (conceptual row) in the dvmrpInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.1 | ColumndvmrpInterfaceIndex | not-accessible | current | The ifIndex value of the interface for which DVMRP is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.2 | ColumndvmrpInterfaceLocalAddress | read-create | current | The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress fo… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.3 | ColumndvmrpInterfaceMetric | read-create | current | The distance metric for this interface which is used to calculate distance vectors. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.4 | ColumndvmrpInterfaceStatus | read-create | current | The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the v… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.5 | ColumndvmrpInterfaceRcvBadPkts | read-only | current | The number of DVMRP messages received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a rout… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.6 | ColumndvmrpInterfaceRcvBadRoutes | read-only | current | The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.7 | ColumndvmrpInterfaceSentRoutes | read-only | current | The number of routes, in DVMRP Report packets, which have been sent on this interface. Together with dvmrpNeighborRcvRoutes at a peer, this object is useful fo… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.8 | ColumndvmrpInterfaceKey | read-create | current | The (shared) key for authenticating neighbors on this interface. This object is intended solely for the purpose of setting the interface key, and MUST be acces… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.9 | ColumndvmrpInterfaceKeyVersion | read-create | current | The highest version number of all known interface keys for this interface used for authenticating neighbors. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.2.1.10 | ColumndvmrpInterfaceGenerationId | read-only | current | The generation identifier for the interface. This is used by neighboring routers to detect whether the DVMRP routing table should be resent. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3 | TabledvmrpNeighborTable | not-accessible | current | The (conceptual) table listing the router's DVMRP neighbors, as discovered by receiving DVMRP messages. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1 | RowdvmrpNeighborEntry | not-accessible | current | An entry (conceptual row) in the dvmrpNeighborTable. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.1 | ColumndvmrpNeighborIfIndex | not-accessible | current | The value of ifIndex for the virtual interface used to reach this DVMRP neighbor. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.2 | ColumndvmrpNeighborAddress | not-accessible | current | The IP address of the DVMRP neighbor for which this entry contains information. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.3 | ColumndvmrpNeighborUpTime | read-only | current | The time since this DVMRP neighbor (last) became a neighbor of the local router. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.4 | ColumndvmrpNeighborExpiryTime | read-only | current | The minimum time remaining before this DVMRP neighbor will be aged out. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.5 | ColumndvmrpNeighborGenerationId | read-only | current | The neighboring router's generation identifier. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.6 | ColumndvmrpNeighborMajorVersion | read-only | current | The neighboring router's major DVMRP version number. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.7 | ColumndvmrpNeighborMinorVersion | read-only | current | The neighboring router's minor DVMRP version number. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.8 | ColumndvmrpNeighborCapabilities | read-only | current | This object describes the neighboring router's capabilities. The leaf bit indicates that the neighbor has only one interface with neighbors. The prune bit indi… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.9 | ColumndvmrpNeighborRcvRoutes | read-only | current | The total number of routes received in valid DVMRP packets received from this neighbor. This can be used to diagnose problems such as unicast route injection, … |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.10 | ColumndvmrpNeighborRcvBadPkts | read-only | current | The number of packet received from this neighbor which were discarded as invalid. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.11 | ColumndvmrpNeighborRcvBadRoutes | read-only | current | The number of routes, in valid DVMRP packets received from this neighbor, which were ignored because the entry was invalid. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.3.1.12 | ColumndvmrpNeighborState | read-only | current | State of the neighbor adjacency. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4 | TabledvmrpRouteTable | not-accessible | current | The table of routes learned through DVMRP route exchange. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1 | RowdvmrpRouteEntry | not-accessible | current | An entry (conceptual row) containing the multicast routing information used by DVMRP in place of the unicast routing information. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.1 | ColumndvmrpRouteSource | not-accessible | current | The network address which when combined with the corresponding value of dvmrpRouteSourceMask identifies the sources for which this entry contains multicast rou… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.2 | ColumndvmrpRouteSourceMask | not-accessible | current | The network mask which when combined with the corresponding value of dvmrpRouteSource identifies the sources for which this entry contains multicast routing in… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.3 | ColumndvmrpRouteUpstreamNeighbor | read-only | current | The address of the upstream neighbor (e.g., RPF neighbor) from which IP datagrams from these sources are received. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.4 | ColumndvmrpRouteIfIndex | read-only | current | The value of ifIndex for the interface on which IP datagrams sent by these sources are received. A value of 0 typically means the route is an aggregate for whi… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.5 | ColumndvmrpRouteMetric | read-only | current | The distance in hops to the source subnet. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.6 | ColumndvmrpRouteExpiryTime | read-only | current | The minimum amount of time remaining before this entry will be aged out. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.4.1.7 | ColumndvmrpRouteUpTime | read-only | current | The time since the route represented by this entry was learned by the router. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.5 | TabledvmrpRouteNextHopTable | not-accessible | current | The (conceptual) table containing information on the next hops on outgoing interfaces for routing IP multicast datagrams. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.5.1 | RowdvmrpRouteNextHopEntry | not-accessible | current | An entry (conceptual row) in the list of next hops on outgoing interfaces to which IP multicast datagrams from particular sources are routed. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.5.1.1 | ColumndvmrpRouteNextHopSource | not-accessible | current | The network address which when combined with the corresponding value of dvmrpRouteNextHopSourceMask identifies the sources for which this entry specifies a nex… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.5.1.2 | ColumndvmrpRouteNextHopSourceMask | not-accessible | current | The network mask which when combined with the corresponding value of dvmrpRouteNextHopSource identifies the sources for which this entry specifies a next hop o… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.5.1.3 | ColumndvmrpRouteNextHopIfIndex | not-accessible | current | The ifIndex value of the interface for the outgoing interface for this next hop. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.5.1.4 | ColumndvmrpRouteNextHopType | read-only | current | Type is leaf if no downstream dependent neighbors exist on the outgoing virtual interface. Otherwise, type is branch. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.6 | TabledvmrpPruneTable | not-accessible | current | The (conceptual) table listing the router's upstream prune state. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.6.1 | RowdvmrpPruneEntry | not-accessible | current | An entry (conceptual row) in the dvmrpPruneTable. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.6.1.1 | ColumndvmrpPruneGroup | not-accessible | current | The group address which has been pruned. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.6.1.2 | ColumndvmrpPruneSource | not-accessible | current | The address of the source or source network which has been pruned. |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.6.1.3 | ColumndvmrpPruneSourceMask | not-accessible | current | The address of the source or source network which has been pruned. The mask must either be all 1's, or else dvmrpPruneSource and dvmrpPruneSourceMask must matc… |
| 1.3.6.1.4.1.259.6.10.57.1.18.4.6.1.4 | ColumndvmrpPruneExpiryTime | read-only | current | The amount of time remaining before this prune should expire at the upstream neighbor. This value should be the minimum of the default prune lifetime and the r… |
| 1.3.6.1.4.1.259.6.10.57.1.18.5 | NoderouteMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2 | TableipCidrRouteExtTable | not-accessible | current | This entity's IP Extension Routing table. |
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2.1 | RowipCidrRouteExtEntry | not-accessible | current | A particular route to a particular destina- tion, under a particular policy. |
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2.1.1 | ColumnipCidrRouteExtDest | not-accessible | current | The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance o… |
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2.1.2 | ColumnipCidrRouteExtMask | not-accessible | current | Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipCidrRouteDest field. For those systems that do n… |
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2.1.3 | ColumnipCidrRouteExtTos | not-accessible | current | The policy specifier is the IP TOS Field. The encoding of IP TOS is as specified by the following convention. Zero indicates the default path if no more specif… |
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2.1.4 | ColumnipCidrRouteExtNextHop | not-accessible | current | On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0. |
| 1.3.6.1.4.1.259.6.10.57.1.18.5.2.1.5 | ColumnipCidrRouteExtOspfSubType | read-only | current | The OSPF SubType, when the ipCidrRouteProto in IP-FORWARD MIB is ospf(13), this object has value (2)-(7), otherwises, this object will always show none(1). |
| 1.3.6.1.4.1.259.6.10.57.1.19 | NodesysLogMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.19.1 | ScalarsysLogStatus | read-write | current | Whether system log is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.19.2 | ScalarsysLogHistoryFlashLevel | read-write | current | Severity level for logging to flash. |
| 1.3.6.1.4.1.259.6.10.57.1.19.3 | ScalarsysLogHistoryRamLevel | read-write | current | Severity level for logging to RAM. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6 | NoderemoteLogMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.19.6.1 | ScalarremoteLogStatus | read-write | current | Whether the remote log system is enabled. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6.2 | ScalarremoteLogLevel | read-write | current | Severity level for remote log. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6.3 | ScalarremoteLogFacilityType | read-write | current | The FacilityType for remote log. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6.4 | TableremoteLogServerTable | not-accessible | current | A Table for storing the remote log Server list. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6.4.1 | RowremoteLogServerEntry | not-accessible | current | A conceptually row for remoteLogServerTable. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6.4.1.1 | ColumnremoteLogServerIp | not-accessible | current | The IP address of the remote log Server. |
| 1.3.6.1.4.1.259.6.10.57.1.19.6.4.1.2 | ColumnremoteLogServerStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7 | NodesmtpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.19.7.1 | ScalarsmtpStatus | read-write | current | Set enabled(1) to enable the SMTP, set disabled(2) to disable the SMTP. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.2 | ScalarsmtpSeverityLevel | read-write | current | specify the SMTP minimum severity level to send the event message. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.3 | ScalarsmtpSourceEMail | read-write | current | SMTP source email address, the sender's mail address that appears in the 'From' field of the mail. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.4 | TablesmtpServerIpTable | not-accessible | current | The table of SMTP server Ip. The maximum servers to be added is 3. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.4.1 | RowsmtpServerIpEntry | not-accessible | current | A conceptual row of the smtpServerIpTable. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.4.1.1 | ColumnsmtpServerIp | accessible-for-notify | current | SMTP mail servers IP address. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.4.1.2 | ColumnsmtpServerIpStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.5 | TablesmtpDestEMailTable | not-accessible | current | The table of the destination e-mail address. The maximum numbers of destination email address to be added is 5. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.5.1 | RowsmtpDestEMailEntry | not-accessible | current | A conceptual row of the smtpDestEMailTable. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.5.1.1 | ColumnsmtpDestEMail | not-accessible | current | SMTP destination e-mail address. |
| 1.3.6.1.4.1.259.6.10.57.1.19.7.5.1.2 | ColumnsmtpDestEMailStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.20 | NodelineMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.20.1 | NodeconsoleMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.20.1.1 | ScalarconsoleDataBits | read-write | current | Number of data bits. |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.2 | ScalarconsoleParity | read-write | current | Define the generation of a parity bit. |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.4 | ScalarconsoleStopBits | read-write | current | The stop Bits of the console, valid value is stopbits1(1) or stopbits2(2) |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.5 | ScalarconsoleExecTimeout | read-write | current | In serial console, use the consoleExecTimeout variables to set the interval that the EXEC command interpreter waits until user input is detected, set the value… |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.6 | ScalarconsolePasswordThreshold | read-write | current | In serial console, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowed.… |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.7 | ScalarconsoleSilentTime | read-write | current | In Console, Use the consoleSilentTime variable to set the amount of time the management console is inaccessible after the number of unsuccessful logon attempts… |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.8 | ScalarconsoleAdminBaudRate | read-write | current | Baud rate. Valid values are 2400, 4800, 9600, 19200, 38400, 57600, 115200. Setting this variable to 0 means autobaud. Please read the actual baud rate in the c… |
| 1.3.6.1.4.1.259.6.10.57.1.20.1.9 | ScalarconsoleOperBaudRate | read-only | current | The baud rate currently in use. |
| 1.3.6.1.4.1.259.6.10.57.1.20.2 | NodetelnetMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.20.2.1 | ScalartelnetExecTimeout | read-write | current | In a telnet session, to set the interval that the EXEC command interpreter waits until user input is detected, use the telnetExecTimeout variables. |
| 1.3.6.1.4.1.259.6.10.57.1.20.2.2 | ScalartelnetPasswordThreshold | read-write | current | In a telnet session, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowe… |
| 1.3.6.1.4.1.259.6.10.57.1.20.2.4 | ScalartelnetStatus | read-write | current | To enable or disable the telnet function. Any new telnet request will be rejected and all current telnet sessions will be terminated if this status is set to d… |
| 1.3.6.1.4.1.259.6.10.57.1.20.2.5 | ScalartelnetPortNumber | read-write | current | The telnet session port number. |
| 1.3.6.1.4.1.259.6.10.57.1.23 | NodesysTimeMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.23.1 | NodesntpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.23.1.1 | ScalarsntpStatus | read-write | current | Set enabled(1) to enable the SNTP, set disabled(2) to disable the SNTP. |
| 1.3.6.1.4.1.259.6.10.57.1.23.1.2 | ScalarsntpServiceMode | read-write | current | Service mode. |
| 1.3.6.1.4.1.259.6.10.57.1.23.1.3 | ScalarsntpPollInterval | read-write | current | Polling interval. |
| 1.3.6.1.4.1.259.6.10.57.1.23.1.4 | TablesntpServerTable | not-accessible | current | Table for SNTP servers |
| 1.3.6.1.4.1.259.6.10.57.1.23.1.4.1 | RowsntpServerEntry | not-accessible | current | Entry for SNTP servers. |
| 1.3.6.1.4.1.259.6.10.57.1.23.1.4.1.1 | ColumnsntpServerIndex | not-accessible | current | The index of a server. This table has fixed size. |
| 1.3.6.1.4.1.259.6.10.57.1.23.1.4.1.2 | ColumnsntpServerIpAddress | read-write | current | The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index is 0. |
| 1.3.6.1.4.1.259.6.10.57.1.23.2 | ScalarsysCurrentTime | read-write | current | It is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' is the first three letters of the English name of the month. '_d' is th… |
| 1.3.6.1.4.1.259.6.10.57.1.23.3 | ScalarsysTimeZone | read-write | current | It is a text string in the following form: '[s]hh:mm'. '[s]' is a plus-or-minus sign. For UTC, this is omitted. For a positive offset, this is '+'. For a negat… |
| 1.3.6.1.4.1.259.6.10.57.1.23.4 | ScalarsysTimeZoneName | read-write | current | The name of the time zone. |
| 1.3.6.1.4.1.259.6.10.57.1.24 | NodefileMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.24.1 | NodefileCopyMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.24.1.1 | ScalarfileCopySrcOperType | read-write | current | The Copy Operation in which we want to perform to the fileCopyDestOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDest… |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.2 | ScalarfileCopySrcFileName | read-write | current | The source file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to the zero length string when no file name has be… |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.3 | ScalarfileCopyDestOperType | read-write | current | The Copy Operation in which we want to perform from the fileCopySrcOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDes… |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.4 | ScalarfileCopyDestFileName | read-write | current | The destination file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to the zero length string when no file name h… |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.5 | ScalarfileCopyFileType | read-write | current | Type of file to copy in fileCopyMgt. If the fileCopySrcOperType or fileCopyDestOperType is either runningCfg(2) or startupCfg(3), this varible can be ignored. … |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.6 | ScalarfileCopyTftpServer | read-write | current | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to '0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.7 | ScalarfileCopyUnitId | read-write | current | Specify the unit of the switch for stackable device when performing the 'copy unit file' or 'copy file unit' action, If neither fileCopySrcOperType nor fileCop… |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.8 | ScalarfileCopyAction | read-write | current | Setting this object to copy(2) to begin the copy Operation. |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.9 | ScalarfileCopyStatus | read-only | current | The status of the last copy procedure, if any. This object will have a value of downloadStatusUnknown(2) if no copy operation has been performed. |
| 1.3.6.1.4.1.259.6.10.57.1.24.1.10 | ScalarfileCopyTftpErrMsg | read-only | current | The tftp error messge, this value is meaningful only when the fileCopyStatus is fileCopyTftpUndefError(1). |
| 1.3.6.1.4.1.259.6.10.57.1.24.2 | NodefileInfoMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1 | TablefileInfoTable | not-accessible | current | This table contain the information of the file system, we can also perfrom the delete, set startup file operation. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1 | RowfileInfoEntry | not-accessible | current | A conceptually row for fileInfoTable. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.1 | ColumnfileInfoUnitID | not-accessible | current | The unit of the switch in a stacking system, in a non-stacking system, it value is always 1. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.2 | ColumnfileInfoFileName | not-accessible | current | The file Name of the file System in the device. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.3 | ColumnfileInfoFileType | read-only | current | The file type of the file System in the device. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.4 | ColumnfileInfoIsStartUp | read-write | current | This flag indicate whether this file is a startup file, Setting this object to truth(1) to indicate this is a startup file, setting this object to false(2) is … |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.5 | ColumnfileInfoFileSize | read-only | current | The sizes( in bytes) of the file. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.6 | ColumnfileInfoCreationTime | read-only | current | The creation time of the file. |
| 1.3.6.1.4.1.259.6.10.57.1.24.2.1.1.7 | ColumnfileInfoDelete | read-write | current | Writing this object to delete(2) to delete a file, when read, this always return noDelete(1). |
| 1.3.6.1.4.1.259.6.10.57.1.26 | NodednsMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.26.1 | ScalardnsDomainLookup | read-write | current | To enable the IP Domain Naming System (DNS)-based host name-to-address translation |
| 1.3.6.1.4.1.259.6.10.57.1.26.2 | ScalardnsDomainName | read-write | current | To define a default domain name to complete unqualified host names (names without a dotted-decimal domain name) |
| 1.3.6.1.4.1.259.6.10.57.1.26.3 | TablednsHostTable | not-accessible | current | This table is used to define static host name-to-address mapping. |
| 1.3.6.1.4.1.259.6.10.57.1.26.3.1 | RowdnsHostEntry | not-accessible | current | A conceptual row for the dnsHostTable. |
| 1.3.6.1.4.1.259.6.10.57.1.26.3.1.1 | ColumndnsHostName | not-accessible | current | The DNS Host name. |
| 1.3.6.1.4.1.259.6.10.57.1.26.3.1.2 | ColumndnsHostIndex | not-accessible | current | The secondary index of this dnsHostTable, representing the sequence of the dnsHostIp. |
| 1.3.6.1.4.1.259.6.10.57.1.26.3.1.3 | ColumndnsHostIp | read-create | current | The DNS Host IP. |
| 1.3.6.1.4.1.259.6.10.57.1.26.4 | TablednsAliasTable | not-accessible | current | This table display the alias of the host name |
| 1.3.6.1.4.1.259.6.10.57.1.26.4.1 | RowdnsAliasEntry | not-accessible | current | A conceptually row for dnsAliasTable. |
| 1.3.6.1.4.1.259.6.10.57.1.26.4.1.1 | ColumndnsAliasName | read-only | current | Host Name |
| 1.3.6.1.4.1.259.6.10.57.1.26.4.1.2 | ColumndnaAliasAlias | read-only | current | Alias |
| 1.3.6.1.4.1.259.6.10.57.1.26.5 | TablednsDomainListTable | not-accessible | current | This table define a list of default domain names to complete unqualified host names |
| 1.3.6.1.4.1.259.6.10.57.1.26.5.1 | RowdnsDomainListEntry | not-accessible | current | A conceptually row for dnsDomainListTable. |
| 1.3.6.1.4.1.259.6.10.57.1.26.5.1.1 | ColumndnsDomainListName | not-accessible | current | Domain Name |
| 1.3.6.1.4.1.259.6.10.57.1.26.5.1.2 | ColumndnsDomainListStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.26.6 | TablednsNameServerTable | not-accessible | current | To specify the address of one or more name servers to use for name and address resolution |
| 1.3.6.1.4.1.259.6.10.57.1.26.6.1 | RowdnsNameServerEntry | not-accessible | current | A conceptually row for dnsNameServerTable. |
| 1.3.6.1.4.1.259.6.10.57.1.26.6.1.1 | ColumndnsNameServerIp | not-accessible | current | Ip address of name server |
| 1.3.6.1.4.1.259.6.10.57.1.26.6.1.2 | ColumndnsNameServerStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.26.7 | TablednsCacheTable | not-accessible | current | To display the RRs in DNS cache |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1 | RowdnsCacheEntry | not-accessible | current | A conceptually row for dnsCacheTable. |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1.1 | ColumndnsCacheIndex | not-accessible | current | The sequence number of the entry |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1.2 | ColumndnsCacheFlag | read-only | current | Always get 4, means this record is unreliable |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1.3 | ColumndnsCacheType | read-only | current | Cache Type: address(1); cname(2). |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1.4 | ColumndnsCacheIp | read-only | current | Cache Ip |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1.5 | ColumndnsCacheTtl | read-only | current | Cache Ttl |
| 1.3.6.1.4.1.259.6.10.57.1.26.7.1.6 | ColumndnsCacheDomain | read-only | current | Cache domain |
| 1.3.6.1.4.1.259.6.10.57.1.29 | NodehsrpMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.29.1 | NodecHsrpGlobalConfig | |||
| 1.3.6.1.4.1.259.6.10.57.1.29.1.1 | ScalarcHsrpConfigTimeout | read-write | current | The amount of time in minutes a row in cHsrpGrpTable can remain in a state other than active before being timed out. |
| 1.3.6.1.4.1.259.6.10.57.1.29.2 | NodecHsrpGroup | |||
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1 | TablecHsrpGrpTable | not-accessible | current | A table containing information on each HSRP group for each interface. |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1 | RowcHsrpGrpEntry | not-accessible | current | Information about an HSRP group. Management applications use cHsrpGrpRowStatus to control entry modification, creation and deletion. Setting cHsrpGrpRowStatus … |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.1 | ColumncHsrpGrpNumber | not-accessible | current | This object along with the ifIndex of a particular interface uniquely identifies an HSRP group. Group numbers 0,1 and 2 are the only valid group numbers for To… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.2 | ColumncHsrpGrpAuth | read-create | current | This is an unencrypted authentication string which is carried in all HSRP messages. An authentication string mismatch prevents a router interface from learning… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.3 | ColumncHsrpGrpPriority | read-create | current | The cHsrpGrpPriority helps to select the active and the standby routers. The router with the highest priority is selected as the active router. In the priority… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.4 | ColumncHsrpGrpPreempt | read-create | current | This object, if TRUE, indicates that the current router should attempt to overthrow a lower priority active router and attempt to become the active router. If … |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.5 | ColumncHsrpGrpPreemptDelay | read-create | current | This delay is the time difference between a router power up and the time it can actually start preempting the currently active router. When a router first come… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.6 | ColumncHsrpGrpUseConfiguredTimers | read-only | current | HSRP routers learn a group's Hellotime or Holdtime from hello messages. The Hellotime is used to determine the frequency of generating hello messages when this… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.7 | ColumncHsrpGrpConfiguredHelloTime | read-create | current | If cHsrpGrpUseConfiguredTimers is true, cHsrpGrpConfiguredHelloTime is used when this router is an active router. Otherwise, the Hellotime learned from the cur… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.8 | ColumncHsrpGrpConfiguredHoldTime | read-create | current | If cHsrpGrpUseConfiguredTimers is true, cHsrpGrpConfiguredHoldTime is used when this router is an active router. Otherwise, the Holdtime learned from the curre… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.9 | ColumncHsrpGrpLearnedHelloTime | read-only | current | If the Hellotime is not configured on a router, it can be learned from the Hello messages from active router, provided the Hello message is authenticated. If t… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.10 | ColumncHsrpGrpLearnedHoldTime | read-only | current | If the Holdtime is not configured on a router, it can be learned from the Hello message from the active router. Holdtime should be learned only if the Hello me… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.11 | ColumncHsrpGrpVirtualIpAddr | read-create | current | This is the primary virtual IP address used by this group. If this address is configured (i.e a non zero ip address), this value is used. Otherwise, the agent … |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.12 | ColumncHsrpGrpUseConfigVirtualIpAddr | read-only | current | If this object is TRUE, cHsrpGrpVirtualIpAddr was a configured one. Otherwise, it indicates that cHsrpGrpVirtualIpAddr was a learned one. |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.13 | ColumncHsrpGrpActiveRouter | read-only | current | Ip Address of the currently active router for this group. |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.14 | ColumncHsrpGrpStandbyRouter | read-only | current | Ip Address of the currently standby router for this group. |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.15 | ColumncHsrpGrpStandbyState | read-only | current | The current HSRP state of this group on this interface. |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.16 | ColumncHsrpGrpVirtualMacAddr | read-only | current | Mac Addresses used are as specified in RFC 2281. For ethernet and fddi interfaces, a MAC address will be in the range 00:00:0c:07:ac:00 through 00:00:0c:07:ac:… |
| 1.3.6.1.4.1.259.6.10.57.1.29.2.1.1.17 | ColumncHsrpGrpEntryRowStatus | read-create | current | The control that allows modification, creation, and deletion of entries. For detailed rules see the DESCRIPTION for cHsrpGrpEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.29.3 | NodecHsrpExtGroup | |||
| 1.3.6.1.4.1.259.6.10.57.1.29.3.1 | TablecHsrpExtIfTrackedTable | not-accessible | current | A table containing information about tracked interfaces per HSRP group. |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.1.1 | RowcHsrpExtIfTrackedEntry | not-accessible | current | The cHsrpExtIfTrackedEntry allows an HSRP group interface to track one or more interfaces. Weight(priority) is given to each and every interface tracked. When … |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.1.1.1 | ColumncHsrpExtIfTracked | not-accessible | current | Index into the cHsrpExtIfTrackedTable for the corresponding { ifIndex, cHsrpGrpNumber } pair i.e for an HSRP group. This is the ifIndex of the tracked interfac… |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.1.1.2 | ColumncHsrpExtIfTrackedPriority | read-create | current | Priority of the tracked interface for the corresponding { ifIndex, cHsrpGrpNumber } pair. In the range of 0 to 255, 0 is the lowest priority and 255 is the hig… |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.1.1.3 | ColumncHsrpExtIfTrackedRowStatus | read-create | current | The control that allows modification, creation, and deletion of entries. For detailed rules see the DESCRIPTION for cHsrpExtIfTrackedEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.2 | TablecHsrpExtSecAddrTable | not-accessible | current | A table containing information about secondary HSRP IP Addresses per interface and group. |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.2.1 | RowcHsrpExtSecAddrEntry | not-accessible | current | The CHsrpExtSecAddrEntry allows creation of secondary IP Addresses for each cHsrpGrpEntry row. Secondary addresses can be added by setting cHsrpExtSecAddrRowSt… |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.2.1.1 | ColumncHsrpExtSecAddrAddress | not-accessible | current | A secondary IpAddress for the {ifIndex, cHsrpGrpNumber} pair. As explained in the DESCRIPTION for cHsrpExtSecAddrEntry, a primary address must exist before a s… |
| 1.3.6.1.4.1.259.6.10.57.1.29.3.2.1.2 | ColumncHsrpExtSecAddrRowStatus | read-create | current | The control that allows modification, creation, and deletion of entries. For detailed rules see the DESCRIPTION for cHsrpExtSecAddrEntry. |
| 1.3.6.1.4.1.259.6.10.57.1.44 | NodemvrMgt | |||
| 1.3.6.1.4.1.259.6.10.57.1.44.1 | ScalarmvrStatus | read-write | current | Parameter to enable or disable MVR(Multicast VLAN Registration) on the device. NOTE: IGMP Snooping must be enabled first before enabling MVR and MVR will be di… |
| 1.3.6.1.4.1.259.6.10.57.1.44.2 | ScalarmvrVlanId | read-write | current | To set VLAN for MVR.The VLAN identified by a particular value of this index is the same VLAN as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-… |
| 1.3.6.1.4.1.259.6.10.57.1.44.3 | ScalarmvrMaxGroups | read-only | current | The maximum number of MVR groups. |
| 1.3.6.1.4.1.259.6.10.57.1.44.4 | ScalarmvrCurrentGroups | read-only | current | The current number of MVR groups. |
| 1.3.6.1.4.1.259.6.10.57.1.44.5 | NodemvrGroupsCtl | |||
| 1.3.6.1.4.1.259.6.10.57.1.44.5.1 | ScalarmvrGroupsCtlId | read-write | current | The start of a contiguous range of MVR group addresses. |
| 1.3.6.1.4.1.259.6.10.57.1.44.5.2 | ScalarmvrGroupsCtlCount | read-write | current | The range count for configuring MVR group addresses. |
| 1.3.6.1.4.1.259.6.10.57.1.44.5.3 | ScalarmvrGroupsCtlAction | read-write | current | Sets the configure action for a contiguous range of MVR group addresses. The start addresses is the current value of mvrGroupsCtlId and the range count is the … |
| 1.3.6.1.4.1.259.6.10.57.1.44.6 | TablemvrGroupTable | not-accessible | current | The table for configuring the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.6.1 | RowmvrGroupEntry | not-accessible | current | The entry for configuring the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.6.1.1 | ColumnmvrGroupId | not-accessible | current | The multicast address of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.6.1.2 | ColumnmvrGroutActive | read-only | current | To indicate if the group has a member or not. If there are no members, the status is inactive(2); otherwise the status is active(1). |
| 1.3.6.1.4.1.259.6.10.57.1.44.6.1.3 | ColumnmvrGroupStatus | read-write | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.44.7 | TablemvrGroupStaticTable | not-accessible | current | The table for configuring the static members of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.7.1 | RowmvrGroupStaticEntry | not-accessible | current | The entry for configuring the static members of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.7.1.1 | ColumnmvrGroupStaticAddress | not-accessible | current | The multicast address of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.7.1.2 | ColumnmvrGroupStaticPorts | read-write | current | The set of ports configured by management in this entry. Ports entered in this list will be the static members of this MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.7.1.3 | ColumnmvrGroupStaticStatus | read-write | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.259.6.10.57.1.44.8 | TablemvrGroupCurrentTable | not-accessible | current | The table for the current members of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.8.1 | RowmvrGroupCurrentEntry | not-accessible | current | The entry for the current members of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.8.1.1 | ColumnmvrGroupCurrentAddress | not-accessible | current | The multicast address of the MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.8.1.2 | ColumnmvrGroupCurrentPorts | read-only | current | The complete set of ports currently associated with this MVR group. |
| 1.3.6.1.4.1.259.6.10.57.1.44.9 | TablemvrPortTable | not-accessible | current | The table for configuring the MVR port. |
| 1.3.6.1.4.1.259.6.10.57.1.44.9.1 | RowmvrPortEntry | not-accessible | current | The entry for configuring the MVR port. |
| 1.3.6.1.4.1.259.6.10.57.1.44.9.1.1 | ColumnmvrIfIndex | not-accessible | current | The port interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIn… |
| 1.3.6.1.4.1.259.6.10.57.1.44.9.1.2 | ColumnmvrPortType | read-write | current | For configuring the MVR port type. To disable the MVR port type, use the none(0). |
| 1.3.6.1.4.1.259.6.10.57.1.44.9.1.3 | ColumnmvrPortImmediateLeave | read-write | current | To enable immediate leave on MVR port. |
| 1.3.6.1.4.1.259.6.10.57.1.44.9.1.4 | ColumnmvrPortActive | read-only | current | To indicate if the port is associated with the MVR group. If the port is the MVR receiver port or the MVR source port in MVR vlan, the status is active(1); oth… |
| 1.3.6.1.4.1.259.6.10.57.1.44.10 | ScalarmvrRunningStatus | read-only | current | Describes the running status of MVR (Multicast VLAN Registration) to the switch. A value of true(1) indicates that all necessary conditions in the MVR environm… |
| 1.3.6.1.4.1.259.6.10.57.2 | Nodees4612MIBNotifications | |||
| 1.3.6.1.4.1.259.6.10.57.2.1 | Nodees4612Traps | |||
| 1.3.6.1.4.1.259.6.10.57.2.1.0 | Nodees4612TrapsPrefix | |||
| 1.3.6.1.4.1.259.6.10.57.2.1.0.1 | NotificationswPowerStatusChangeTrap | current | This trap is sent when the power status of an individual power changes. | |
| 1.3.6.1.4.1.259.6.10.57.2.1.0.17 | NotificationswFanFailureTrap | current | This trap is sent when the fan is failure. | |
| 1.3.6.1.4.1.259.6.10.57.2.1.0.18 | NotificationswFanRecoverTrap | current | This trap is sent when fan failure has recovered. | |
| 1.3.6.1.4.1.259.6.10.57.2.1.0.36 | NotificationswPortSecurityTrap | current | This trap is sent when the port is being intruded. This trap will only be sent when the portSecActionTrap is enabled. | |
| 1.3.6.1.4.1.259.6.10.57.2.1.0.41 | NotificationswSmtpConnFailureTrap | current | This trap will be triggered if the SMTP system cannot open a connection to the mail server successfully. | |
| 1.3.6.1.4.1.259.6.10.57.3 | Nodees4612MIBConformance |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HsrpState | INTEGER { initial(1), learn(2), listen(3), speak(4), standby(5), active(6) } | current | The current state of the HSRP protocol for a given HSRP group entry. |
| OspfAreaID | IpAddress | current | An OSPF Area Identifier. |
| OspfBigMetric | Integer32 (0..'FFFFFE'h) | current | The OSPF External Metric. |
| StaPathCostMode | INTEGER { short(1), long(2) } | current | The path cost mode of a spanning tree algorithm, short(1) indicates that we retrieve/configure the spanning tree path cost as a 16 bit value and long(2) indicates that we retrieve/configure the spanning tree path cost a… |
| ValidStatus | INTEGER { valid(1), invalid(2) } | current | A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destr… |