ESN310-MIB
331 objects
The MIB module for esn310.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.193.72.900 | Identityesn310MIB | The MIB module for esn310. | ||
| 1.3.6.1.4.1.193.72.900.1 | Nodeesn310MIBObjects | |||
| 1.3.6.1.4.1.193.72.900.1.1 | NodeswitchMgt | |||
| 1.3.6.1.4.1.193.72.900.1.1.1 | ScalarswitchManagementVlan | read-write | current | The VLAN on which management is done. |
| 1.3.6.1.4.1.193.72.900.1.1.2 | ScalarswitchNumber | read-only | current | The total number of switches present on this system. |
| 1.3.6.1.4.1.193.72.900.1.1.3 | TableswitchInfoTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1 | RowswitchInfoEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.1 | ColumnswUnitIndex | not-accessible | current | This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.2 | ColumnswHardwareVer | read-only | current | Hardware version of the main board. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.3 | ColumnswMicrocodeVer | read-only | current | Microcode version of the main board. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.4 | ColumnswLoaderVer | read-only | current | Loader version of the main board. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.5 | ColumnswBootRomVer | read-only | current | Boot ROM code version of the main board. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.6 | ColumnswOpCodeVer | read-only | current | Operation code version of the main board. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.7 | ColumnswPortNumber | read-only | current | The total port number of this switch (including expansion slot). |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.8 | ColumnswPowerStatus | read-only | current | Indicates the switch using internalPower(1), redundantPower(2) or both(3) |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.9 | ColumnswRoleInSystem | read-only | current | Indicates the switch is master(1), backupMaster(2) or slave(3) in this system. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.10 | ColumnswSerialNumber | read-only | current | Serial number of the switch. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.11 | ColumnswExpansionSlot1 | read-only | current | Type of expansion module in this switch slot 1. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.12 | ColumnswExpansionSlot2 | read-only | current | Type of expansion module in this switch slot 2. |
| 1.3.6.1.4.1.193.72.900.1.1.3.1.13 | ColumnswServiceTag | read-only | current | Service tag serial-number of the switch. |
| 1.3.6.1.4.1.193.72.900.1.1.4 | ScalarswitchOperState | read-only | current | Global operation state of the switch. |
| 1.3.6.1.4.1.193.72.900.1.1.5 | NodeswitchProductId | |||
| 1.3.6.1.4.1.193.72.900.1.1.5.1 | ScalarswProdName | read-only | current | |
| 1.3.6.1.4.1.193.72.900.1.1.5.2 | ScalarswProdManufacturer | read-only | current | |
| 1.3.6.1.4.1.193.72.900.1.1.5.3 | ScalarswProdDescription | read-only | current | |
| 1.3.6.1.4.1.193.72.900.1.1.5.4 | ScalarswProdVersion | read-only | current | |
| 1.3.6.1.4.1.193.72.900.1.1.5.5 | ScalarswProdUrl | read-only | current | |
| 1.3.6.1.4.1.193.72.900.1.1.5.6 | ScalarswIdentifier | read-only | current | A unique identifier of which switch in the chassis is currently being looked at. |
| 1.3.6.1.4.1.193.72.900.1.1.5.7 | ScalarswChassisServiceTag | read-only | current | The service tag of the chassis this switch resides in. |
| 1.3.6.1.4.1.193.72.900.1.1.6 | TableswitchIndivPowerTable | not-accessible | current | Table about statuses of individual powers. |
| 1.3.6.1.4.1.193.72.900.1.1.6.1 | RowswitchIndivPowerEntry | not-accessible | current | Table about statuses of individual powers. |
| 1.3.6.1.4.1.193.72.900.1.1.6.1.1 | ColumnswIndivPowerUnitIndex | read-only | current | This is defined as swUnitIndex. |
| 1.3.6.1.4.1.193.72.900.1.1.6.1.2 | ColumnswIndivPowerIndex | read-only | current | 1 means internal power. 2 means external power. |
| 1.3.6.1.4.1.193.72.900.1.1.6.1.3 | ColumnswIndivPowerStatus | read-only | current | notPresent(1) means not present. green(2) means up. red(3) means down. |
| 1.3.6.1.4.1.193.72.900.1.2 | NodeportMgt | |||
| 1.3.6.1.4.1.193.72.900.1.2.1 | TableportTable | not-accessible | current | Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains informa… |
| 1.3.6.1.4.1.193.72.900.1.2.1.1 | RowportEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.1 | ColumnportIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.2 | ColumnportName | read-write | current | Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later). |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.3 | ColumnportType | read-only | current | Indicates the port type. |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.4 | ColumnportSpeedDpxCfg | read-write | current | Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 1… |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.5 | ColumnportFlowCtrlCfg | read-write | current | (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPr… |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.6 | ColumnportCapabilities | read-write | current | Port capabilities. |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.7 | ColumnportAutonegotiation | read-write | current | Whether autonegotiation is enabled. |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.8 | ColumnportSpeedDpxStatus | read-only | current | The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk … |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.9 | ColumnportFlowCtrlStatus | read-only | current | (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trun… |
| 1.3.6.1.4.1.193.72.900.1.2.1.1.10 | ColumnportTrunkIndex | read-only | current | The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to… |
| 1.3.6.1.4.1.193.72.900.1.3 | NodetrunkMgt | |||
| 1.3.6.1.4.1.193.72.900.1.3.1 | ScalartrunkMaxId | read-only | current | The maximum number for a trunk identifier. |
| 1.3.6.1.4.1.193.72.900.1.3.2 | ScalartrunkValidNumber | read-only | current | The number of valid trunks. |
| 1.3.6.1.4.1.193.72.900.1.3.3 | TabletrunkTable | not-accessible | current | Table of descriptive and status information about configuration of each trunk, similar to Cisco EtherChannel. |
| 1.3.6.1.4.1.193.72.900.1.3.3.1 | RowtrunkEntry | not-accessible | current | An entry in the table, containing information about configuration in one trunk of the switch. |
| 1.3.6.1.4.1.193.72.900.1.3.3.1.1 | ColumntrunkIndex | not-accessible | current | This object identifies the trunk within the switch for which this entry contains information. |
| 1.3.6.1.4.1.193.72.900.1.3.3.1.2 | ColumntrunkPorts | read-create | current | The complete set of ports currently associated with this trunk. |
| 1.3.6.1.4.1.193.72.900.1.3.3.1.3 | ColumntrunkCreation | read-only | current | A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk. |
| 1.3.6.1.4.1.193.72.900.1.3.3.1.4 | ColumntrunkStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.193.72.900.1.4 | NodelacpMgt | |||
| 1.3.6.1.4.1.193.72.900.1.4.1 | TablelacpPortTable | not-accessible | current | Table for LACP port configuration. |
| 1.3.6.1.4.1.193.72.900.1.4.1.1 | RowlacpPortEntry | not-accessible | current | Entry for LACP port configuration. |
| 1.3.6.1.4.1.193.72.900.1.4.1.1.1 | ColumnlacpPortIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.4.1.1.2 | ColumnlacpPortStatus | read-write | current | Whether 802.3ad LACP is enabled. |
| 1.3.6.1.4.1.193.72.900.1.5 | NodestaMgt | |||
| 1.3.6.1.4.1.193.72.900.1.5.1 | ScalarstaSystemStatus | read-write | current | Global spanning tree status: (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.193.72.900.1.5.2 | TablestaPortTable | not-accessible | current | The table manages port settings for Spanning Tree Protocol 802.1d, or 802.1w depending on the value specified by staProtocolType. |
| 1.3.6.1.4.1.193.72.900.1.5.2.1 | RowstaPortEntry | not-accessible | current | The conceptual entry of staPortTable. |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.2 | ColumnstaPortFastForward | read-write | current | Whether fast forwarding is enabled. |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.3 | ColumnstaPortProtocolMigration | read-write | current | When operating in RSTP (version 2) mode, setting this object to TRUE(1) object forces the port to transmit RSTP BPDUs. Any other operation on this object has n… |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.4 | ColumnstaPortAdminEdgePort | read-write | current | The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed to be an edge-port and a value of FALSE(2) i… |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.5 | ColumnstaPortOperEdgePort | read-only | current | The operational value of the Edge Port parameter. The object is initialized to the value of staPortAdminEdgePort and is set FALSE when a BPDU is received. |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.6 | ColumnstaPortAdminPointToPoint | read-write | current | The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as… |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.7 | ColumnstaPortOperPointToPoint | read-only | current | The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection o… |
| 1.3.6.1.4.1.193.72.900.1.5.2.1.8 | ColumnstaPortLongPathCost | read-write | current | The contribution of this port to the path cost (as a 32 bit value) of paths towards the spanning tree root which include this port. This object is used to conf… |
| 1.3.6.1.4.1.193.72.900.1.5.3 | ScalarstaProtocolType | read-write | current | The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'… |
| 1.3.6.1.4.1.193.72.900.1.5.4 | ScalarstaTxHoldCount | read-write | current | The minimum interval between the transmission of consecutive RSTP/MSTP BPDUs in seconds. |
| 1.3.6.1.4.1.193.72.900.1.5.5 | ScalarstaPathCostMethod | read-write | current | Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the Spanning tree protocol running on the sw… |
| 1.3.6.1.4.1.193.72.900.1.5.6 | NodexstMgt | |||
| 1.3.6.1.4.1.193.72.900.1.5.6.4 | TablexstInstanceCfgTable | not-accessible | current | This table is used to configure Rapid Spanning Tree. Only the first row of the table is used by RST. In the future this table may be used to support other span… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1 | RowxstInstanceCfgEntry | not-accessible | current | A conceptual row containing the properties of the RST instance. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.1 | ColumnxstInstanceCfgIndex | not-accessible | current | The index for an entry in the xstInstanceCfgTable table. For RST only the first row in the table is used. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.2 | ColumnxstInstanceCfgPriority | read-write | current | The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.3 | ColumnxstInstanceCfgTimeSinceTopologyChange | read-only | current | The time (in hundredths of second) since the last topology change detected by the bridge entity in RST. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.4 | ColumnxstInstanceCfgTopChanges | read-only | current | The total number of topology changes detected by this bridge in RST since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.5 | ColumnxstInstanceCfgDesignatedRoot | read-only | current | The bridge identifier of the root of the spanning tree as determined by the Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as … |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.6 | ColumnxstInstanceCfgRootCost | read-only | current | The cost of the path to the root as seen from this bridge of the RST. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.7 | ColumnxstInstanceCfgRootPort | read-only | current | The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST . |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.8 | ColumnxstInstanceCfgMaxAge | read-only | current | The maximum age of Rapid Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. Th… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.9 | ColumnxstInstanceCfgHelloTime | read-only | current | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become … |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.10 | ColumnxstInstanceCfgHoldTime | read-only | current | This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredth… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.11 | ColumnxstInstanceCfgForwardDelay | read-only | current | For the RST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.12 | ColumnxstInstanceCfgBridgeMaxAge | read-only | current | For RST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies th… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.13 | ColumnxstInstanceCfgBridgeHelloTime | read-only | current | For the RST protocol, the time (in hundredths of second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this tim… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.14 | ColumnxstInstanceCfgBridgeForwardDelay | read-only | current | For the RST protocol, the time (in hundredths of second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 sp… |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.15 | ColumnxstInstanceCfgTxHoldCount | read-only | current | For the RST protocol, the value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.193.72.900.1.5.6.4.1.16 | ColumnxstInstanceCfgPathCostMethod | read-only | current | For RST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol r… |
| 1.3.6.1.4.1.193.72.900.1.5.6.5 | TablexstInstancePortTable | not-accessible | current | The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1 | RowxstInstancePortEntry | not-accessible | current | The conceptual row for xstInstancePortTable. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.3 | ColumnxstInstancePortPriority | read-write | current | Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest prior… |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.4 | ColumnxstInstancePortState | read-only | current | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discard… |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.5 | ColumnxstInstancePortEnable | read-only | current | The enabled/disabled status of the port. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.6 | ColumnxstInstancePortPathCost | read-write | current | The pathcost of the RST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assig… |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.7 | ColumnxstInstancePortDesignatedRoot | read-only | current | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the po… |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.8 | ColumnxstInstancePortDesignatedCost | read-only | current | The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.9 | ColumnxstInstancePortDesignatedBridge | read-only | current | The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.10 | ColumnxstInstancePortDesignatedPort | read-only | current | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.11 | ColumnxstInstancePortForwardTransitions | read-only | current | The number of times this port has transitioned from the Learning state to the Forwarding state. |
| 1.3.6.1.4.1.193.72.900.1.5.6.5.1.12 | ColumnxstInstancePortPortRole | read-only | current | The role of the port in the RST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge t… |
| 1.3.6.1.4.1.193.72.900.1.6 | NodetftpMgt | |||
| 1.3.6.1.4.1.193.72.900.1.6.1 | ScalartftpFileType | read-write | current | Type of file to transfer. |
| 1.3.6.1.4.1.193.72.900.1.6.2 | ScalartftpSrcFile | read-write | current | The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been s… |
| 1.3.6.1.4.1.193.72.900.1.6.3 | ScalartftpDestFile | read-write | current | The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has b… |
| 1.3.6.1.4.1.193.72.900.1.6.4 | ScalartftpServer | read-write | current | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.193.72.900.1.6.5 | ScalartftpAction | read-write | current | When this object is set to downloadToRAM(2) or downloadToPROM(3), the device will discontinue its normal operation and begin download of the file specified by … |
| 1.3.6.1.4.1.193.72.900.1.6.6 | ScalartftpStatus | read-only | current | The status of the last transfer procedure, if any. This object will have a value of downloadStatusUnknown(2) if no transfer process has been performed. |
| 1.3.6.1.4.1.193.72.900.1.7 | NoderestartMgt | |||
| 1.3.6.1.4.1.193.72.900.1.7.1 | ScalarrestartOpCodeFile | read-write | current | Name of op-code file for start-up. |
| 1.3.6.1.4.1.193.72.900.1.7.2 | ScalarrestartConfigFile | read-write | current | Name of configuration file for start-up. |
| 1.3.6.1.4.1.193.72.900.1.7.3 | ScalarrestartControl | read-write | current | Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Se… |
| 1.3.6.1.4.1.193.72.900.1.8 | NodemirrorMgt | |||
| 1.3.6.1.4.1.193.72.900.1.8.1 | TablemirrorTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.193.72.900.1.8.1.1 | RowmirrorEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.193.72.900.1.8.1.1.1 | ColumnmirrorDestinationPort | not-accessible | current | Destination port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.8.1.1.2 | ColumnmirrorSourcePort | not-accessible | current | Source port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.8.1.1.3 | ColumnmirrorType | read-create | current | If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and… |
| 1.3.6.1.4.1.193.72.900.1.8.1.1.4 | ColumnmirrorStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.193.72.900.1.9 | NodeigmpSnoopMgt | |||
| 1.3.6.1.4.1.193.72.900.1.9.1 | ScalarigmpSnoopStatus | read-write | current | Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. |
| 1.3.6.1.4.1.193.72.900.1.9.2 | ScalarigmpSnoopQuerier | read-write | current | Whether to act as querier. |
| 1.3.6.1.4.1.193.72.900.1.9.3 | ScalarigmpSnoopQueryCount | read-write | current | Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports. |
| 1.3.6.1.4.1.193.72.900.1.9.4 | ScalarigmpSnoopQueryInterval | read-write | current | Query interval. |
| 1.3.6.1.4.1.193.72.900.1.9.5 | ScalarigmpSnoopQueryMaxResponseTime | read-write | current | Timeout value (seconds) between IGMP reports received on a port for an IP Multicast Address that can pass before the system sends an IGMP Query out the port an… |
| 1.3.6.1.4.1.193.72.900.1.9.6 | ScalarigmpSnoopQueryTimeout | read-write | current | Query time-out. |
| 1.3.6.1.4.1.193.72.900.1.9.7 | ScalarigmpSnoopVersion | read-write | current | Version. |
| 1.3.6.1.4.1.193.72.900.1.9.8 | TableigmpSnoopRouterCurrentTable | not-accessible | current | Table for current router ports. |
| 1.3.6.1.4.1.193.72.900.1.9.8.1 | RowigmpSnoopRouterCurrentEntry | not-accessible | current | Entry for current router ports. |
| 1.3.6.1.4.1.193.72.900.1.9.8.1.1 | ColumnigmpSnoopRouterCurrentVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.193.72.900.1.9.8.1.2 | ColumnigmpSnoopRouterCurrentPorts | read-only | current | The set of ports which are current router ports. Within this list, some router ports are static router ports. Please refer to igmpSnoopRouterStaticTable. |
| 1.3.6.1.4.1.193.72.900.1.9.8.1.3 | ColumnigmpSnoopRouterCurrentStatus | read-only | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.193.72.900.1.9.9 | TableigmpSnoopRouterStaticTable | not-accessible | current | Table for static router ports. |
| 1.3.6.1.4.1.193.72.900.1.9.9.1 | RowigmpSnoopRouterStaticEntry | not-accessible | current | Entry for static router ports. |
| 1.3.6.1.4.1.193.72.900.1.9.9.1.1 | ColumnigmpSnoopRouterStaticVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.193.72.900.1.9.9.1.2 | ColumnigmpSnoopRouterStaticPorts | read-create | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.193.72.900.1.9.9.1.3 | ColumnigmpSnoopRouterStaticStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.193.72.900.1.9.10 | TableigmpSnoopMulticastCurrentTable | not-accessible | current | Table for current multicast addresses. |
| 1.3.6.1.4.1.193.72.900.1.9.10.1 | RowigmpSnoopMulticastCurrentEntry | not-accessible | current | Entry for current multicast addresses. |
| 1.3.6.1.4.1.193.72.900.1.9.10.1.1 | ColumnigmpSnoopMulticastCurrentVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.193.72.900.1.9.10.1.2 | ColumnigmpSnoopMulticastCurrentIpAddress | not-accessible | current | IP address of multicast group. |
| 1.3.6.1.4.1.193.72.900.1.9.10.1.3 | ColumnigmpSnoopMulticastCurrentPorts | read-only | current | The set of ports which are members. |
| 1.3.6.1.4.1.193.72.900.1.9.10.1.4 | ColumnigmpSnoopMulticastCurrentStatus | read-only | current | The set of ports which are static members. |
| 1.3.6.1.4.1.193.72.900.1.9.11 | TableigmpSnoopMulticastStaticTable | not-accessible | current | Table for static multicast addresses. |
| 1.3.6.1.4.1.193.72.900.1.9.11.1 | RowigmpSnoopMulticastStaticEntry | not-accessible | current | Entry for static multicast addresses. |
| 1.3.6.1.4.1.193.72.900.1.9.11.1.1 | ColumnigmpSnoopMulticastStaticVlanIndex | not-accessible | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.193.72.900.1.9.11.1.2 | ColumnigmpSnoopMulticastStaticIpAddress | not-accessible | current | IP address of multicast group. |
| 1.3.6.1.4.1.193.72.900.1.9.11.1.3 | ColumnigmpSnoopMulticastStaticPorts | read-create | current | The set of ports which are members. |
| 1.3.6.1.4.1.193.72.900.1.9.11.1.4 | ColumnigmpSnoopMulticastStaticStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.193.72.900.1.10 | NodeipMgt | |||
| 1.3.6.1.4.1.193.72.900.1.10.1 | TablenetConfigTable | not-accessible | current | A table of netConfigEntries. |
| 1.3.6.1.4.1.193.72.900.1.10.1.1 | RownetConfigEntry | not-accessible | current | A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is … |
| 1.3.6.1.4.1.193.72.900.1.10.1.1.1 | ColumnnetConfigIfIndex | not-accessible | current | VLAN interface on which this entry is defined. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.10.1.1.2 | ColumnnetConfigIPAddress | not-accessible | current | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then w… |
| 1.3.6.1.4.1.193.72.900.1.10.1.1.3 | ColumnnetConfigSubnetMask | not-accessible | current | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then … |
| 1.3.6.1.4.1.193.72.900.1.10.1.1.4 | ColumnnetConfigPrimaryInterface | read-create | current | Whether this is a primary interface. |
| 1.3.6.1.4.1.193.72.900.1.10.1.1.5 | ColumnnetConfigUnnumbered | read-create | current | Whether this is an unnumbered interface. |
| 1.3.6.1.4.1.193.72.900.1.10.1.1.6 | ColumnnetConfigStatus | read-create | current | The status of this netConfigEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. |
| 1.3.6.1.4.1.193.72.900.1.10.2 | ScalarnetDefaultGateway | read-write | current | The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0. |
| 1.3.6.1.4.1.193.72.900.1.10.3 | ScalaripHttpState | read-write | current | Whether HTTP is enabled. |
| 1.3.6.1.4.1.193.72.900.1.10.4 | ScalaripHttpPort | read-write | current | The port number for HTTP. |
| 1.3.6.1.4.1.193.72.900.1.10.5 | ScalaripDhcpRestart | read-write | current | Write it to restart(1) to restart DHCP. When read, this value always returns noRestart(2). |
| 1.3.6.1.4.1.193.72.900.1.10.6 | ScalaripHttpsState | read-write | current | Whether HTTPS is enabled. |
| 1.3.6.1.4.1.193.72.900.1.10.7 | ScalaripHttpsPort | read-write | current | The port number for HTTPS. |
| 1.3.6.1.4.1.193.72.900.1.11 | NodebcastStormMgt | |||
| 1.3.6.1.4.1.193.72.900.1.11.1 | TablebcastStormTable | not-accessible | current | Table of descriptive and status information about configuration of each switch ports(including expansion slot) in this system. |
| 1.3.6.1.4.1.193.72.900.1.11.1.1 | RowbcastStormEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.193.72.900.1.11.1.1.1 | ColumnbcastStormIfIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.11.1.1.2 | ColumnbcastStormStatus | read-write | current | Whether broadcast storm protection is enabled. |
| 1.3.6.1.4.1.193.72.900.1.11.1.1.3 | ColumnbcastStormSampleType | read-write | current | Sample type. If this is pkt-rate(1), then bcastStormPktRate is valid. If this is octet-rate(2), then bcastStormOctetRate is valid. If this is percent(3), then … |
| 1.3.6.1.4.1.193.72.900.1.11.1.1.4 | ColumnbcastStormPktRate | read-write | current | Broadcast storm threshold as packets per second. |
| 1.3.6.1.4.1.193.72.900.1.11.1.1.5 | ColumnbcastStormOctetRate | read-write | current | Broadcast storm threshold as octets per second. |
| 1.3.6.1.4.1.193.72.900.1.11.1.1.6 | ColumnbcastStormPercent | read-write | current | Broadcast storm threshold as percentage of bandwidth. |
| 1.3.6.1.4.1.193.72.900.1.12 | NodevlanMgt | |||
| 1.3.6.1.4.1.193.72.900.1.12.1 | TablevlanTable | not-accessible | current | Table for VLAN configuration. |
| 1.3.6.1.4.1.193.72.900.1.12.1.1 | RowvlanEntry | not-accessible | current | Entry for VLAN configuration. |
| 1.3.6.1.4.1.193.72.900.1.12.1.1.1 | ColumnvlanIndex | not-accessible | current | Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface. |
| 1.3.6.1.4.1.193.72.900.1.12.1.1.2 | ColumnvlanAddressMethod | read-write | current | Method to get the IP address. |
| 1.3.6.1.4.1.193.72.900.1.12.2 | TablevlanPortTable | not-accessible | current | Table for port configuration in VLAN. |
| 1.3.6.1.4.1.193.72.900.1.12.2.1 | RowvlanPortEntry | not-accessible | current | Entry for port configuration in VLAN. |
| 1.3.6.1.4.1.193.72.900.1.12.2.1.1 | ColumnvlanPortIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.12.2.1.2 | ColumnvlanPortMode | read-write | current | This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) set… |
| 1.3.6.1.4.1.193.72.900.1.13 | NodepriorityMgt | |||
| 1.3.6.1.4.1.193.72.900.1.13.1 | ScalarprioIpPrecDscpStatus | read-write | current | Whether IP precedence or DSCP look-up is enabled. |
| 1.3.6.1.4.1.193.72.900.1.13.2 | TableprioIpPrecTable | not-accessible | current | Table for IP precedence priority mapping. |
| 1.3.6.1.4.1.193.72.900.1.13.2.1 | RowprioIpPrecEntry | not-accessible | current | Entry for IP precendence priority mapping. |
| 1.3.6.1.4.1.193.72.900.1.13.2.1.2 | ColumnprioIpPrecPort | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.13.2.1.3 | ColumnprioIpPrecValue | not-accessible | current | Precedence value for this entry. |
| 1.3.6.1.4.1.193.72.900.1.13.2.1.4 | ColumnprioIpPrecCos | read-write | current | Class of service for this entry. |
| 1.3.6.1.4.1.193.72.900.1.13.3 | ScalarprioIpPrecRestoreDefault | read-write | current | This object is to restore IP Precedence settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When … |
| 1.3.6.1.4.1.193.72.900.1.13.4 | TableprioIpDscpTable | not-accessible | current | Table for IP DSCP priority mapping. |
| 1.3.6.1.4.1.193.72.900.1.13.4.1 | RowprioIpDscpEntry | not-accessible | current | Entry for IP DSCP priority mapping. |
| 1.3.6.1.4.1.193.72.900.1.13.4.1.1 | ColumnprioIpDscpPort | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.13.4.1.2 | ColumnprioIpDscpValue | not-accessible | current | DSCP value for this entry. |
| 1.3.6.1.4.1.193.72.900.1.13.4.1.3 | ColumnprioIpDscpCos | read-write | current | Class of service for this entry. |
| 1.3.6.1.4.1.193.72.900.1.13.5 | ScalarprioIpDscpRestoreDefault | read-write | current | This object is to restore IP DSCP settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, … |
| 1.3.6.1.4.1.193.72.900.1.13.6 | ScalarprioIpPortEnableStatus | read-write | current | Whether IP Port priority look-up is enabled. |
| 1.3.6.1.4.1.193.72.900.1.13.7 | TableprioIpPortTable | not-accessible | current | Table for IP port priority mapping. |
| 1.3.6.1.4.1.193.72.900.1.13.7.1 | RowprioIpPortEntry | not-accessible | current | Entry for IP port priority mapping. |
| 1.3.6.1.4.1.193.72.900.1.13.7.1.1 | ColumnprioIpPortPhysPort | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.193.72.900.1.13.7.1.2 | ColumnprioIpPortValue | not-accessible | current | IP port for this value. |
| 1.3.6.1.4.1.193.72.900.1.13.7.1.3 | ColumnprioIpPortCos | read-create | current | Class of service for this entry. |
| 1.3.6.1.4.1.193.72.900.1.13.7.1.4 | ColumnprioIpPortStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.193.72.900.1.13.8 | NodeprioCopy | |||
| 1.3.6.1.4.1.193.72.900.1.13.8.1 | ScalarprioCopyIpPrec | read-write | current | Action to copy IP Precedence settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-… |
| 1.3.6.1.4.1.193.72.900.1.13.8.2 | ScalarprioCopyIpDscp | read-write | current | Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (b… |
| 1.3.6.1.4.1.193.72.900.1.13.8.3 | ScalarprioCopyIpPort | read-write | current | Action to copy IP Port settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (b… |
| 1.3.6.1.4.1.193.72.900.1.13.9 | TableprioWrrTable | not-accessible | current | Table for weighted round robin (WRR). |
| 1.3.6.1.4.1.193.72.900.1.13.9.1 | RowprioWrrEntry | not-accessible | current | Entry for weighted round robin (WRR). |
| 1.3.6.1.4.1.193.72.900.1.13.9.1.1 | ColumnprioWrrTrafficClass | not-accessible | current | Traffic class for this entry, as defined in dot1dTrafficClass in the Q-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTraf… |
| 1.3.6.1.4.1.193.72.900.1.13.9.1.2 | ColumnprioWrrWeight | read-write | current | Weight for this entry. |
| 1.3.6.1.4.1.193.72.900.1.14 | NodetrapDestMgt | |||
| 1.3.6.1.4.1.193.72.900.1.14.1 | TabletrapDestTable | not-accessible | current | A list of trap destination entries. |
| 1.3.6.1.4.1.193.72.900.1.14.1.1 | RowtrapDestEntry | not-accessible | current | This entry includes a destination IP address to which to send traps for this community. |
| 1.3.6.1.4.1.193.72.900.1.14.1.1.1 | ColumntrapDestAddress | not-accessible | current | The address to send traps. |
| 1.3.6.1.4.1.193.72.900.1.14.1.1.2 | ColumntrapDestCommunity | read-create | current | A community to which this destination address belongs. |
| 1.3.6.1.4.1.193.72.900.1.14.1.1.3 | ColumntrapDestStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.193.72.900.1.14.1.1.4 | ColumntrapDestVersion | read-create | current | This variables represent the version of the Trap we wish to send to trap Receiver, if the value is 1, mean we wish to send Version 1 trap, if the value is 2, m… |
| 1.3.6.1.4.1.193.72.900.1.14.2 | NodetrapVar | |||
| 1.3.6.1.4.1.193.72.900.1.14.2.8 | ScalartrapVarMibObjId | accessible-for-notify | current | Object ID of the mib variable. |
| 1.3.6.1.4.1.193.72.900.1.16 | NodeqosMgt | |||
| 1.3.6.1.4.1.193.72.900.1.16.1 | NoderateLimitMgt | |||
| 1.3.6.1.4.1.193.72.900.1.16.1.1 | ScalarrateLimitStatus | read-write | current | Whether rate limit is enabled. |
| 1.3.6.1.4.1.193.72.900.1.16.1.2 | TablerateLimitPortTable | not-accessible | current | Table for rate limit of each port. |
| 1.3.6.1.4.1.193.72.900.1.16.1.2.1 | RowrateLimitPortEntry | not-accessible | current | Entry for rate limit of each port. |
| 1.3.6.1.4.1.193.72.900.1.16.1.2.1.1 | ColumnrlPortIndex | not-accessible | current | The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface … |
| 1.3.6.1.4.1.193.72.900.1.16.1.2.1.2 | ColumnrlPortInputLimit | read-write | current | Value of the input rate limit. Its unit is megabits per second. For a 100 Mb/s port, the range is 1 to 100. For a 1000 Mb/s port, the range is 1 to 1000. |
| 1.3.6.1.4.1.193.72.900.1.16.1.2.1.3 | ColumnrlPortOutputLimit | read-write | current | Value of the output rate limit. Its unit is megabits per second. For a 100 Mb/s port, the range is 1 to 100. For a 1000 Mb/s port, the range is 1 to 1000. |
| 1.3.6.1.4.1.193.72.900.1.16.1.2.1.6 | ColumnrlPortInputStatus | read-write | current | Whether input rate limit is enabled for this port. |
| 1.3.6.1.4.1.193.72.900.1.16.1.2.1.7 | ColumnrlPortOutputStatus | read-write | current | Whether output rate limit is enabled for this port. |
| 1.3.6.1.4.1.193.72.900.1.17 | NodesecurityMgt | |||
| 1.3.6.1.4.1.193.72.900.1.17.1 | NodeprivateVlanMgt | |||
| 1.3.6.1.4.1.193.72.900.1.17.1.4 | TableprivateVlanVlanTable | not-accessible | current | A table containing Private VLAN information on the VLANs which currently exist. |
| 1.3.6.1.4.1.193.72.900.1.17.1.4.1 | RowprivateVlanVlanEntry | not-accessible | current | A conceptual row containing the Private VLAN information on the VLANs for a particular management domain. |
| 1.3.6.1.4.1.193.72.900.1.17.1.4.1.1 | ColumnprivateVlanVlanIndex | not-accessible | current | The VLAN-id of this private VLAN. |
| 1.3.6.1.4.1.193.72.900.1.17.1.4.1.2 | ColumnprivateVlanVlanType | read-create | current | The VLAN type as defined for Private VLAN feature. Set the value to invalid(1) to destory an entry, set other value to create an entry, if an index is already … |
| 1.3.6.1.4.1.193.72.900.1.17.1.4.1.3 | ColumnprivateVlanAssoicatedPrimaryVlan | read-create | current | The VLAN ID of the associated primary VLAN used for the Private VLAN feature if privateVlanVlanType has the value of isolated(3), community(4). If privateVlanV… |
| 1.3.6.1.4.1.193.72.900.1.17.2 | NodeportSecurityMgt | |||
| 1.3.6.1.4.1.193.72.900.1.17.2.1 | TableportSecPortTable | not-accessible | current | The Port Security(MAC bindind) Table |
| 1.3.6.1.4.1.193.72.900.1.17.2.1.1 | RowportSecPortEntry | not-accessible | current | The entry of portSecPortTable |
| 1.3.6.1.4.1.193.72.900.1.17.2.1.1.1 | ColumnportSecPortIndex | not-accessible | current | The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.193.72.900.1.17.2.1.1.2 | ColumnportSecPortStatus | read-write | current | Set enabled(1) to enable port security and set disabled(2) to disable port security. |
| 1.3.6.1.4.1.193.72.900.1.17.2.1.1.3 | ColumnportSecAction | read-write | current | The corresponding actions that will take place when a port is under intruded, when this variable is set to none(1), no action will perform, when this variable … |
| 1.3.6.1.4.1.193.72.900.1.17.2.1.1.4 | ColumnportSecMaxMacCount | read-write | current | The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will di… |
| 1.3.6.1.4.1.193.72.900.1.17.4 | NoderadiusMgt | |||
| 1.3.6.1.4.1.193.72.900.1.17.4.1 | ScalarradiusServerAddress | read-write | current | IP address of RADIUS server. |
| 1.3.6.1.4.1.193.72.900.1.17.4.2 | ScalarradiusServerPortNumber | read-write | current | IP port number of RADIUS server. |
| 1.3.6.1.4.1.193.72.900.1.17.4.3 | ScalarradiusServerKey | read-write | current | Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string. |
| 1.3.6.1.4.1.193.72.900.1.17.4.4 | ScalarradiusServerRetransmit | read-write | current | Maximum number of retransmissions for RADIUS. |
| 1.3.6.1.4.1.193.72.900.1.17.4.5 | ScalarradiusServerTimeout | read-write | current | Timeout for RADIUS. |
| 1.3.6.1.4.1.193.72.900.1.17.5 | NodetacacsMgt | |||
| 1.3.6.1.4.1.193.72.900.1.17.5.1 | ScalartacacsServerAddress | read-write | current | IP address of TACACS server. |
| 1.3.6.1.4.1.193.72.900.1.17.5.2 | ScalartacacsServerPortNumber | read-write | current | IP port number of TACACS server. |
| 1.3.6.1.4.1.193.72.900.1.17.5.3 | ScalartacacsServerKey | read-write | current | The encryption key used to authenticate logon access for the client using TACAS. Do not use blank spaces in the string. (Maximum length: 20 characters). This v… |
| 1.3.6.1.4.1.193.72.900.1.17.6 | NodesshMgt | |||
| 1.3.6.1.4.1.193.72.900.1.17.6.1 | ScalarsshServerStatus | read-write | current | The status of Secure Shell Server, set this value to 1 to enable SSH server, set this value to 2 to disable the SSH server. |
| 1.3.6.1.4.1.193.72.900.1.17.6.2 | ScalarsshServerMajorVersion | read-only | current | The major version of the SSH Server. |
| 1.3.6.1.4.1.193.72.900.1.17.6.3 | ScalarsshServerMinorVersion | read-only | current | The minor version of the SSH Server. |
| 1.3.6.1.4.1.193.72.900.1.17.6.4 | ScalarsshTimeout | read-write | current | The time interval that the router waits for the SSH client to respond. The range is 1-120. |
| 1.3.6.1.4.1.193.72.900.1.17.6.5 | ScalarsshAuthRetries | read-write | current | The number of attempts after which the interface is reset. The range is 1-5. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6 | TablesshConnInfoTable | not-accessible | current | The table for Secure Shell Connection. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1 | RowsshConnInfoEntry | not-accessible | current | The conceptual row for sshConnInfoTable. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.1 | ColumnsshConnID | not-accessible | current | The connection ID of the Secure Shell Connection. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.2 | ColumnsshConnMajorVersion | read-only | current | The SSH major version. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.3 | ColumnsshConnMinorVersion | read-only | current | The SSH minor version. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.4 | ColumnsshConnEncryptionType | read-only | current | The encryption type of the SSH. none(1) mean no encrytion , des(2) mean using DES encrytion, tribeDes mean using 3DES encrytion. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.5 | ColumnsshConnStatus | read-only | current | The SSH connection State. negotiationStart(1) mean the SSH is in its negotiation start state, authenticationStart(2) mean the SSH is in authentication start st… |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.6 | ColumnsshConnUserName | read-only | current | The user name of the connection. |
| 1.3.6.1.4.1.193.72.900.1.17.6.6.1.7 | ColumnsshDisconnect | read-write | current | Set the variables to disconnect to disconnect the connection, when read, this variables always return noDisconnect(1). |
| 1.3.6.1.4.1.193.72.900.1.19 | NodesysLogMgt | |||
| 1.3.6.1.4.1.193.72.900.1.19.1 | ScalarsysLogStatus | read-write | current | Whether system log is enabled. |
| 1.3.6.1.4.1.193.72.900.1.19.2 | ScalarsysLogHistoryFlashLevel | read-write | current | Severity level for logging to flash. |
| 1.3.6.1.4.1.193.72.900.1.19.3 | ScalarsysLogHistoryRamLevel | read-write | current | Severity level for logging to RAM. |
| 1.3.6.1.4.1.193.72.900.1.20 | NodelineMgt | |||
| 1.3.6.1.4.1.193.72.900.1.20.1 | NodeconsoleMgt | |||
| 1.3.6.1.4.1.193.72.900.1.20.1.1 | ScalarconsoleDataBits | read-write | current | Number of data bits. |
| 1.3.6.1.4.1.193.72.900.1.20.1.2 | ScalarconsoleParity | read-write | current | Define the generation of a parity bit. |
| 1.3.6.1.4.1.193.72.900.1.20.1.3 | ScalarconsoleBaudRate | read-write | current | Baud rate. Valid values are 115200, 57600, 38400, 19200, and 9600. |
| 1.3.6.1.4.1.193.72.900.1.20.1.4 | ScalarconsoleStopBits | read-write | current | The stop Bits of the console, valid value is stopbits1(1) or stopbits2(2) |
| 1.3.6.1.4.1.193.72.900.1.20.1.5 | ScalarconsoleExecTimeout | read-write | current | In serial console, use the consoleExecTimeout variables to set the interval that the EXEC command interpreter waits until user input is detected, set the value… |
| 1.3.6.1.4.1.193.72.900.1.20.1.6 | ScalarconsolePasswordThreshold | read-write | current | In serial console, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowed.… |
| 1.3.6.1.4.1.193.72.900.1.20.1.7 | ScalarconsoleSilentTime | read-write | current | In Console, Use the consoleSilentTime variable to set the amount of time the management console is inaccessible after the number of unsuccessful logon attempts… |
| 1.3.6.1.4.1.193.72.900.1.20.2 | NodetelnetMgt | |||
| 1.3.6.1.4.1.193.72.900.1.20.2.1 | ScalartelnetExecTimeout | read-write | current | In a telnet session, to set the interval that the EXEC command interpreter waits until user input is detected, use the telnetExecTimeout variables. |
| 1.3.6.1.4.1.193.72.900.1.20.2.2 | ScalartelnetPasswordThreshold | read-write | current | In a telnet session, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowe… |
| 1.3.6.1.4.1.193.72.900.1.23 | NodesysTimeMgt | |||
| 1.3.6.1.4.1.193.72.900.1.23.1 | NodesntpMgt | |||
| 1.3.6.1.4.1.193.72.900.1.23.1.1 | ScalarsntpStatus | read-write | current | Set enabled(1) to enable the SNTP, set disabled(2) to disable the SNTP. |
| 1.3.6.1.4.1.193.72.900.1.23.1.2 | ScalarsntpServiceMode | read-write | current | Service mode. |
| 1.3.6.1.4.1.193.72.900.1.23.1.3 | ScalarsntpPollInterval | read-write | current | Polling interval. |
| 1.3.6.1.4.1.193.72.900.1.23.1.4 | TablesntpServerTable | not-accessible | current | Table for SNTP servers |
| 1.3.6.1.4.1.193.72.900.1.23.1.4.1 | RowsntpServerEntry | not-accessible | current | Entry for SNTP servers. |
| 1.3.6.1.4.1.193.72.900.1.23.1.4.1.1 | ColumnsntpServerIndex | not-accessible | current | The index of a server. This table has fixed size. |
| 1.3.6.1.4.1.193.72.900.1.23.1.4.1.2 | ColumnsntpServerIpAddress | read-write | current | The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index is 0. |
| 1.3.6.1.4.1.193.72.900.1.23.2 | ScalarsysCurrentTime | read-write | current | It is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' is the first three letters of the English name of the month. '_d' is th… |
| 1.3.6.1.4.1.193.72.900.1.23.3 | ScalarsysTimeZone | read-write | current | It is a text string in the following form: '[s]hh:mm'. '[s]' is a plus-or-minus sign. For UTC, this is omitted. For a positive offset, this is '+'. For a negat… |
| 1.3.6.1.4.1.193.72.900.1.23.4 | ScalarsysTimeZoneName | read-write | current | The name of the time zone. |
| 1.3.6.1.4.1.193.72.900.1.24 | NodefileMgt | |||
| 1.3.6.1.4.1.193.72.900.1.24.1 | NodefileCopyMgt | |||
| 1.3.6.1.4.1.193.72.900.1.24.1.1 | ScalarfileCopySrcOperType | read-write | current | The Copy Operation in which we want to perform to the fileCopyDestOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDest… |
| 1.3.6.1.4.1.193.72.900.1.24.1.2 | ScalarfileCopySrcFileName | read-write | current | The source file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to the zero length string when no file name has be… |
| 1.3.6.1.4.1.193.72.900.1.24.1.3 | ScalarfileCopyDestOperType | read-write | current | The Copy Operation in which we want to perform from the fileCopySrcOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDes… |
| 1.3.6.1.4.1.193.72.900.1.24.1.4 | ScalarfileCopyDestFileName | read-write | current | The destination file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to the zero length string when no file name h… |
| 1.3.6.1.4.1.193.72.900.1.24.1.5 | ScalarfileCopyFileType | read-write | current | Type of file to copy in fileCopyMgt. If the fileCopySrcOperType or fileCopyDestOperType is either runningCfg(2) or startupCfg(3), this varible can be ignored. … |
| 1.3.6.1.4.1.193.72.900.1.24.1.6 | ScalarfileCopyTftpServer | read-write | current | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to '0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.193.72.900.1.24.1.7 | ScalarfileCopyUnitId | read-write | current | Specify the unit of the switch for stackable device when performing the 'copy unit file' or 'copy file unit' action, If neither fileCopySrcOperType nor fileCop… |
| 1.3.6.1.4.1.193.72.900.1.24.1.8 | ScalarfileCopyAction | read-write | current | Setting this object to copy(2) to begin the copy Operation. |
| 1.3.6.1.4.1.193.72.900.1.24.1.9 | ScalarfileCopyStatus | read-only | current | The status of the last copy procedure, if any. This object will have a value of downloadStatusUnknown(2) if no copy operation has been performed. |
| 1.3.6.1.4.1.193.72.900.1.24.2 | NodefileInfoMgt | |||
| 1.3.6.1.4.1.193.72.900.1.24.2.1 | TablefileInfoTable | not-accessible | current | This table contain the information of the file system, we can also perfrom the delete, set startup file operation. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1 | RowfileInfoEntry | not-accessible | current | A conceptually row for fileInfoTable. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.1 | ColumnfileInfoUnitID | not-accessible | current | The unit of the switch in a stacking system, in a non-stacking system, it value is always 1. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.2 | ColumnfileInfoFileName | not-accessible | current | The file Name of the file System in the device. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.3 | ColumnfileInfoFileType | read-only | current | The file type of the file System in the device. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.4 | ColumnfileInfoIsStartUp | read-write | current | This flag indicate whether this file is a startup file, Setting this object to truth(1) to indicate this is a startup file, setting this object to false(2) is … |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.5 | ColumnfileInfoFileSize | read-only | current | The sizes( in bytes) of the file. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.6 | ColumnfileInfoCreationTime | read-only | current | The creation time of the file. |
| 1.3.6.1.4.1.193.72.900.1.24.2.1.1.7 | ColumnfileInfoDelete | read-write | current | Writing this object to delete(2) to delete a file, when read, this always return noDelete(1). |
| 1.3.6.1.4.1.193.72.900.1.27 | NodeledCtrlMgt | |||
| 1.3.6.1.4.1.193.72.900.1.27.1 | ScalarledCtrlMgtColorOnOffTime | read-write | current | Indicates the control led color and on off time. |
| 1.3.6.1.4.1.193.72.900.2 | Nodeesn310Notifications | |||
| 1.3.6.1.4.1.193.72.900.2.1 | Nodeesn310Traps | |||
| 1.3.6.1.4.1.193.72.900.2.1.0 | Nodeesn310TrapsPrefix | |||
| 1.3.6.1.4.1.193.72.900.2.1.0.1 | NotificationswPowerStatusChangeTrap | current | This trap is sent when the power status of an individual power changes. | |
| 1.3.6.1.4.1.193.72.900.2.1.0.42 | NotificationswSettingToAllInterfacesTrap | current | This trap is issued when a MIB object defined on a per-interface basis is being set, but because of a system limitation, this set action is applied to all inte… | |
| 1.3.6.1.4.1.193.72.900.3 | Nodeesn310Conformance |