ETH-SWITCH-MIB
150 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter TimeTicks |
| RFC1213-MIB | DisplayString |
| SCANET-MIB | scanet |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.208.39 | NodeethSwitch | |||
| 1.3.6.1.4.1.208.39.1 | Nodecontrol | |||
| 1.3.6.1.4.1.208.39.1 | NodeethSwitchPermVioEvent | This trap is sent when there has been a permanent entry violation. A MAC address has been detected at an other port than the port where it has been configured … | ||
| 1.3.6.1.4.1.208.39.1.1 | ScalarscSegments | read-write | mandatory | Object controlling the use of the System Center Backplane. Each bus is assigned a bit value in the object |
| 1.3.6.1.4.1.208.39.1.2 | ScalardefaultSwitchMode | read-write | mandatory | Default Switch mode. used by the object portSwitchMode when its value is default(1) |
| 1.3.6.1.4.1.208.39.1.3 | ScalardefaultThrottleBackMode | read-write | mandatory | Default ThrottleBack mode. used by the object portThrottleBack when its value is default(1) |
| 1.3.6.1.4.1.208.39.1.4 | ScalarnetworkPort | read-write | mandatory | For a Workgroup Switch (only one multi MAC address port), this object determines the network port. The value equals the value of portNumber in the portTable. N… |
| 1.3.6.1.4.1.208.39.2 | NodeethSwitchOnlyOneMACEvent | This trap is sent when a port detects more that one MAC address at a port intended for only one MAC. This Trap can only be sent from a Concentrator Switch wher… | ||
| 1.3.6.1.4.1.208.39.2 | Nodemodule | |||
| 1.3.6.1.4.1.208.39.2.1 | ScalarexpansionModule | read-only | mandatory | An ID that identifies the expansion module |
| 1.3.6.1.4.1.208.39.3 | NodeethSwitchMACVioEvent | This trap is sent when there has been detected a MAC access control violation. A MAC address has been detected at a port with MAC access restriction, and the M… | ||
| 1.3.6.1.4.1.208.39.3 | Nodeports | |||
| 1.3.6.1.4.1.208.39.3.1 | ScalarportLastChange | read-only | mandatory | The value of sysUpTime at the last time any interface has changed state |
| 1.3.6.1.4.1.208.39.3.2 | TableportTable | not-accessible | mandatory | Port Table. |
| 1.3.6.1.4.1.208.39.3.2.1 | RowportEntry | not-accessible | mandatory | A Port entry containing object for a Switch port. |
| 1.3.6.1.4.1.208.39.3.2.1.1 | ColumnportNumber | read-only | mandatory | A number that uniquely identifies a port |
| 1.3.6.1.4.1.208.39.3.2.1.2 | ColumnportInterfaceIndex | read-only | mandatory | The value of this object equals the ports interface index value, ex. portIfIndex. If the value of this object is zero, then the port is not active, i.e. does n… |
| 1.3.6.1.4.1.208.39.3.2.1.3 | ColumnportLED | read-only | mandatory | The value of this object represent the status (colour) of the LED(s) attached to this port. Lower 3 bits indicates off/colour (off(0), red(1), green(2), yellow… |
| 1.3.6.1.4.1.208.39.3.2.1.4 | ColumnportState | read-only | mandatory | This is a bit array which represent the state of the port. bit 0: Disabled due to configuration bit 1: Hardware error bit 2: No linkpulse bit 3: Disabled by ma… |
| 1.3.6.1.4.1.208.39.3.2.1.5 | ColumnportCardNumber | read-only | mandatory | The cardNumber in the switch system. |
| 1.3.6.1.4.1.208.39.3.2.1.6 | ColumnportPimNumber | read-only | mandatory | The pimNumber in the switch system. |
| 1.3.6.1.4.1.208.39.3.2.1.7 | ColumnportPimPortNumber | read-only | mandatory | The relative number of the port on the PIM. |
| 1.3.6.1.4.1.208.39.3.3 | TableportIfTable | not-accessible | mandatory | Switch Interface Table. |
| 1.3.6.1.4.1.208.39.3.3.1 | RowportIfEntry | not-accessible | mandatory | An entry containing object for a Switch interface. |
| 1.3.6.1.4.1.208.39.3.3.1.1 | ColumnportIfIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.208.39.3.3.1.2 | ColumnportIfDescr | read-write | mandatory | User configurable description of the port. |
| 1.3.6.1.4.1.208.39.3.3.1.3 | ColumnportIfLocation | read-write | mandatory | User configurable location of the port. |
| 1.3.6.1.4.1.208.39.3.3.1.4 | ColumnportIfSwitchMode | read-write | mandatory | Port Switch mode. If set to default(1) value from defaultSwitchMode is used. |
| 1.3.6.1.4.1.208.39.3.3.1.5 | ColumnportIfDuplex | read-only | mandatory | Port Duplex mode. For ports in auto mode the mode may change automatically between autoDetect(1), autoDetectedHalf(3) and autoDetectedFull(5). |
| 1.3.6.1.4.1.208.39.3.3.1.6 | ColumnportIfThrottleBack | read-write | mandatory | Port ThrottleBack mode. If set to default(1) value from defaultThrottleBackMode is used. |
| 1.3.6.1.4.1.208.39.3.3.1.7 | ColumnportIfType | read-only | mandatory | The type of Physical interface at the port. |
| 1.3.6.1.4.1.208.39.3.3.1.8 | ColumnportIfDuplexSupported | read-only | mandatory | The duplex mode supported for a port. |
| 1.3.6.1.4.1.208.39.3.3.1.9 | ColumnportIfSpeedSupported | read-only | mandatory | The speed supported for a port. |
| 1.3.6.1.4.1.208.39.3.3.1.10 | ColumnportIfSpeedAndDuplex | read-write | mandatory | This object is used to configure the speed and duplex mode for a port. Byte 1: negotiation manual(0) autoDisable(1) autoAlternative(2) Byte 2: speed auto(1) 10… |
| 1.3.6.1.4.1.208.39.4 | NodeethSwitchAdaptiveForwEvent | This trap is sent when a port automatically is changing forwarding mode. This will only happen when the port has been configured to Adaptive mode. The syntax i… | ||
| 1.3.6.1.4.1.208.39.4 | Nodestatistic | |||
| 1.3.6.1.4.1.208.39.4.1 | TabletxStatTable | not-accessible | mandatory | MIA ASIC Transmit statistic Table. |
| 1.3.6.1.4.1.208.39.4.1.1 | RowtxStatEntry | not-accessible | mandatory | An entry containing object for MIA ASIC Transmit statistic. |
| 1.3.6.1.4.1.208.39.4.1.1.1 | ColumntxStatIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.208.39.4.1.1.2 | ColumntxUCPkts64Octets | read-only | mandatory | 64 byte unicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.3 | ColumntxUCPkts65To127Octets | read-only | mandatory | 65 to 127 byte unicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.4 | ColumntxUCPkts128To255Octets | read-only | mandatory | 128 to 255 byte unicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.5 | ColumntxUCPkts256To511Octets | read-only | mandatory | 256 to 511 byte unicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.6 | ColumntxUCPkts512To1023Octets | read-only | mandatory | 512 to 1023 byte unicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.7 | ColumntxUCPkts1024To1518Octets | read-only | mandatory | 1024 to 1518 byte unicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.8 | ColumntxMCPkts64Octets | read-only | mandatory | 64 byte multicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.9 | ColumntxMCPkts65To127Octets | read-only | mandatory | 65 to 127 byte multicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.10 | ColumntxMCPkts128To255Octets | read-only | mandatory | 128 to 255 byte multicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.11 | ColumntxMCPkts256To511Octets | read-only | mandatory | 256 to 511 byte multicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.12 | ColumntxMCPkts512To1023Octets | read-only | mandatory | 512 to 1023 byte multicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.13 | ColumntxMCPkts1024To1518Octets | read-only | mandatory | 1024 to 1518 byte multicast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.14 | ColumntxBCPkts64Octets | read-only | mandatory | 64 byte broadcast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.15 | ColumntxBCPkts65To127Octets | read-only | mandatory | 65 to 127 byte broadcast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.16 | ColumntxBCPkts128To255Octets | read-only | mandatory | 128 to 255 byte broadcast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.17 | ColumntxBCPkts256To511Octets | read-only | mandatory | 256 to 511 byte broadcast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.18 | ColumntxBCPkts512To1023Octets | read-only | mandatory | 512 to 1023 byte broadcast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.19 | ColumntxBCPkts1024To1518Octets | read-only | mandatory | 1024 to 1518 byte broadcast packets transmitted |
| 1.3.6.1.4.1.208.39.4.1.1.20 | ColumntxDeffereds | read-only | mandatory | A transmission must await a silent net in Simplex mode. If the transmission is delayed due to a non silent net the transmission is deffered. |
| 1.3.6.1.4.1.208.39.4.1.1.21 | ColumntxOctetsHis | read-only | mandatory | High part of a 64 bit octet transmitted counter |
| 1.3.6.1.4.1.208.39.4.1.1.22 | ColumntxOctetsLos | read-only | mandatory | Low part of a 64 bit octet transmitted counter |
| 1.3.6.1.4.1.208.39.4.1.1.23 | ColumntxExcessiveDefferalsErrors | read-only | mandatory | Maximum defferal should be the duration of a maximum length packet, if no errors on the net. Excessive defferal is indicated if defferal duration is more than … |
| 1.3.6.1.4.1.208.39.4.1.1.24 | ColumntxForwardedRxError | read-only | mandatory | The transmission are aborted on the transmitting port of the switch if the receiving port of the present packet receives are packet with error or receives a co… |
| 1.3.6.1.4.1.208.39.4.1.1.25 | ColumntxNiaUnderRunDrops | read-only | mandatory | The NIA TX buffer gets in underrun if the nimbus is overloaded. This should only happen if a configuration is made which loads the Nimbus with more than a load… |
| 1.3.6.1.4.1.208.39.4.1.1.26 | ColumntxLinkDownEvents | read-only | mandatory | No link pulses are received. Usually this means that the cable are removed. |
| 1.3.6.1.4.1.208.39.4.1.1.27 | ColumntxAllCounterPackets | read-only | mandatory | A collection of all counters for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are txStatIndex INTEGER … |
| 1.3.6.1.4.1.208.39.4.1.1.28 | ColumntxAllCounterOthers | read-only | mandatory | A collection of all counters other than for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are txStatInd… |
| 1.3.6.1.4.1.208.39.4.2 | TablerxStatTable | not-accessible | mandatory | MIA ASIC Receive statistic Table. |
| 1.3.6.1.4.1.208.39.4.2.1 | RowrxStatEntry | not-accessible | mandatory | An entry containing object for MIA ASIC Receive statistic. |
| 1.3.6.1.4.1.208.39.4.2.1.1 | ColumnrxStatIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.208.39.4.2.1.2 | ColumnrxUCPkts64OctetsLocals | read-only | mandatory | 64 byte unicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.3 | ColumnrxUCPkts64OctetsForwardeds | read-only | mandatory | 64 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.4 | ColumnrxUCPkts65To127OctetsLocals | read-only | mandatory | 65 to 127 byte unicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.5 | ColumnrxUCPkts65To127OctetsForwardeds | read-only | mandatory | 65 to 127 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.6 | ColumnrxUCPkts128To255OctetsLocals | read-only | mandatory | 128 to 255 byte unicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.7 | ColumnrxUCPkts128To255OctetsForwardeds | read-only | mandatory | 128 to 255 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.8 | ColumnrxUCPkts256To511OctetsLocals | read-only | mandatory | 256 to 511 byte unicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.9 | ColumnrxUCPkts256To511OctetsForwardeds | read-only | mandatory | 255 to 511 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.10 | ColumnrxUCPkts512To1023OctetsLocals | read-only | mandatory | 512 to 1023 byte unicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.11 | ColumnrxUCPkts512To1023OctetsForwardeds | read-only | mandatory | 512 to 1023 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.12 | ColumnrxUCPkts1024To1518OctetsLocals | read-only | mandatory | 1024 to 1518 byte unicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.13 | ColumnrxUCPkts1024To1518OctetsForwardeds | read-only | mandatory | 1024 to 1518 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.14 | ColumnrxShortErrors | read-only | mandatory | Receive fragments shorter than minimum ordinary collision fragment. |
| 1.3.6.1.4.1.208.39.4.2.1.15 | ColumnrxRuntErrors | read-only | mandatory | Ordinary collision fragments received. |
| 1.3.6.1.4.1.208.39.4.2.1.16 | ColumnrxDataRateMMErrors | read-only | mandatory | Data Rate Miss Match Error occurs if the data rate deviation is larger than allowed. This should only occur if problems with the TX oscillator in the adapter t… |
| 1.3.6.1.4.1.208.39.4.2.1.17 | ColumnrxMCPkts64OctetsLocals | read-only | mandatory | 64 byte multicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.18 | ColumnrxMCPkts64OctetsForwardeds | read-only | mandatory | 64 byte multicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.19 | ColumnrxMCPkts65To127OctetsLocals | read-only | mandatory | 65 to 127 byte multicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.20 | ColumnrxMCPkts65To127OctetsForwardeds | read-only | mandatory | 65 to 127 byte multicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.21 | ColumnrxMCPkts128To255OctetsLocals | read-only | mandatory | 128 to 255 byte multicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.22 | ColumnrxMCPkts128To255OctetsForwardeds | read-only | mandatory | 128 to 255 byte multicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.23 | ColumnrxMCPkts256To511OctetsLocals | read-only | mandatory | 256 to 511 byte multicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.24 | ColumnrxMCPkts256To511OctetsForwardeds | read-only | mandatory | 256 to 511 byte multicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.25 | ColumnrxMCPkts512To1023OctetsLocals | read-only | mandatory | 512 to 1023 byte multicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.26 | ColumnrxMCPkts512To1023OctetsForwardeds | read-only | mandatory | 512 to 1023 byte multicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.27 | ColumnrxMCPkts1024To1518OctetsLocals | read-only | mandatory | 1024 to 1518 byte multicast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.28 | ColumnrxMCPkts1024To1518OctetsForwardeds | read-only | mandatory | 1024 to 1518 byte multicast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.29 | ColumnrxOctetsLocalHis | read-only | mandatory | High part of a 64 bit octet received counter which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.30 | ColumnrxOctetsLocalLos | read-only | mandatory | Low part of a 64 bit octet received counter which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.31 | ColumnrxOctetsForwardedHis | read-only | mandatory | High part of a 64 bit octet received counter which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.32 | ColumnrxOctetsForwardedLos | read-only | mandatory | Low part of a 64 bit octet received counter which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.33 | ColumnrxBCPkts64OctetsLocals | read-only | mandatory | 64 byte broadcast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.34 | ColumnrxBCPkts64OctetsForwardeds | read-only | mandatory | 64 byte broadcast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.35 | ColumnrxBCPkts65To127OctetsLocals | read-only | mandatory | 65 to 127 byte broadcast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.36 | ColumnrxBCPkts65To127OctetsForwardeds | read-only | mandatory | 65 to 127 byte broadcast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.37 | ColumnrxBCPkts128To255OctetsLocals | read-only | mandatory | 128 to 255 byte broadcast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.38 | ColumnrxBCPkts128To255OctetsForwardeds | read-only | mandatory | 128 to 255 byte broadcast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.39 | ColumnrxBCPkts256To511OctetsLocals | read-only | mandatory | 256 to 511 byte broadcast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.40 | ColumnrxBCPkts256To511OctetsForwardeds | read-only | mandatory | 256 to 511 byte broadcast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.41 | ColumnrxBCPkts512To1023OctetsLocals | read-only | mandatory | 512 to 1023 byte broadcast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.42 | ColumnrxBCPkts512To1023OctetsForwardeds | read-only | mandatory | 512 to 1023 byte broadcast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.43 | ColumnrxBCPkts1024To1518OctetsLocals | read-only | mandatory | 1024 to 1518 byte broadcast packets received which has not been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.44 | ColumnrxBCPkts1024To1518OctetsForwardeds | read-only | mandatory | 1024 to 1518 byte broadcast packets received which has been forwarded |
| 1.3.6.1.4.1.208.39.4.2.1.45 | ColumnrxFilterMACUnexp2ndPortDrops | read-only | mandatory | MAC address has been moved from one port to another |
| 1.3.6.1.4.1.208.39.4.2.1.46 | ColumnrxFilterIllegalMACDrops | read-only | mandatory | Indicate more than one MAC address on a port which is not a network port or in general that the filter discards a packet due to an illegal source MAC address |
| 1.3.6.1.4.1.208.39.4.2.1.47 | ColumnrxFlowCtrlCollCounter | read-only | mandatory | This counter counts the number of Flow Control collisions, which are generated due to flow control. Flow control are used when most of the pool memory are used… |
| 1.3.6.1.4.1.208.39.4.2.1.48 | ColumnrxVeryLongErrors | read-only | mandatory | Occurs only if frame longer than 6000 bytes are received. |
| 1.3.6.1.4.1.208.39.4.2.1.49 | ColumnrxLongErrors | read-only | mandatory | Occurs if a frame longer than 1518 bytes and shorter than 6000 bytes are received. |
| 1.3.6.1.4.1.208.39.4.2.1.50 | ColumnrxPiaOutOfPoolsDrop | read-only | mandatory | Reception is aborted due to lack of Pool memory. The switch is overloaded. |
| 1.3.6.1.4.1.208.39.4.2.1.51 | ColumnrxManchesterCodeViolationErrors | read-only | mandatory | An illegal symbol received on a 100Base-X port. |
| 1.3.6.1.4.1.208.39.4.2.1.52 | ColumnrxRxJabbers | read-only | mandatory | Jabber is counted instead of a long error if the frame contains dribble bits or FCS error. |
| 1.3.6.1.4.1.208.39.4.2.1.53 | ColumnrxNiaOverRunDrops | read-only | mandatory | The NIA RX buffer gets in overrun if the nimbus is overloaded. This should only happen if a configuration is made which loads the Nimbus with more than a load … |
| 1.3.6.1.4.1.208.39.4.2.1.54 | ColumnrxAllCounterPackets | read-only | mandatory | A collection of all counters for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are rxStatIndex INTEGER … |
| 1.3.6.1.4.1.208.39.4.2.1.55 | ColumnrxAllCounterOthers | read-only | mandatory | A collection of all counters other than for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are rxStatInd… |
| 1.3.6.1.4.1.208.39.4.3 | ScalartotalRxTxPackets | read-only | mandatory | This object is used for LED control to display traffic. Values in the string are all packets transmitted and received at each port. The number and order of val… |
| 1.3.6.1.4.1.208.39.4.4 | ScalartotalCollisions | read-only | mandatory | This object is used for LED control to display collision. Values in the string are the total collisions at each port. The number and order of values equals the… |
| 1.3.6.1.4.1.208.39.5 | NodeadaptiveForwardMode | |||
| 1.3.6.1.4.1.208.39.5 | NodeethSwitchMACFilterVioEvent | Port/MAC filter MAC violation on port: %portIfIndex% This trap is sent when there has been detected a MAC address on a port (portIfIndex), where this MAC is no… | ||
| 1.3.6.1.4.1.208.39.5.1 | ScalaradaptiveForwardModeSampleTime | read-write | mandatory | Specify how long (sec) the received packets will be monitored. The resulting forwarding mode will be based on the quality of the packets |
| 1.3.6.1.4.1.208.39.5.2 | ScalaradaptiveForwardModeRuntsOffset | read-write | mandatory | Specifies the minimum amount of runts during the sample time which forces the port out of cutThrough(2). The value is specified in per mille * 1000 |
| 1.3.6.1.4.1.208.39.5.3 | ScalaradaptiveForwardModeRuntsRange | read-write | mandatory | Specifies together with adaptiveForwardModeRuntsOffset the maximum amount of runts allowed during the sample time, which forces the port back to cutThrough(2).… |
| 1.3.6.1.4.1.208.39.5.4 | ScalaradaptiveForwardModeCrcsOffset | read-write | mandatory | Specifies the maximum amount of crc errors during the sample time which forces the port out of Store and Forward. The value is specified in per mille * 1000 |
| 1.3.6.1.4.1.208.39.5.5 | ScalaradaptiveForwardModeCrcsRange | read-write | mandatory | Specifies together with adaptiveForwardModeCrcsOffset the maximum amount of crc errors during the sample time which forces the port out of Store and Forward. T… |
| 1.3.6.1.4.1.208.39.6 | NodechipSets | |||
| 1.3.6.1.4.1.208.39.6.1 | NodechipSetNIA10 | |||
| 1.3.6.1.4.1.208.39.6.2 | NodechipSetNIA100 | |||
| 1.3.6.1.4.1.208.39.7 | Nodecards | |||
| 1.3.6.1.4.1.208.39.7.1 | TablecardTable | not-accessible | mandatory | This table describes which cards a switch system consist of and how they are connected. |
| 1.3.6.1.4.1.208.39.7.1.1 | RowcardEntry | not-accessible | mandatory | An entry contains either a card or an expansion card and how many PIMs it contains. |
| 1.3.6.1.4.1.208.39.7.1.1.1 | ColumncardNumber | read-only | mandatory | The card index number. |
| 1.3.6.1.4.1.208.39.7.1.1.2 | ColumncardId | read-only | mandatory | The produce identification the card. |
| 1.3.6.1.4.1.208.39.7.1.1.3 | ColumncardFirstPort | read-only | mandatory | The portNumber of the first port on the card. |
| 1.3.6.1.4.1.208.39.7.1.1.4 | ColumncardMaxPims | read-only | mandatory | The maximum number of PIMs this card can contain. |
| 1.3.6.1.4.1.208.39.7.2 | TablepimTable | not-accessible | mandatory | This table describes the PIMs inserted in the switch system. |
| 1.3.6.1.4.1.208.39.7.2.1 | RowpimEntry | not-accessible | mandatory | An entry describes the PIM. |
| 1.3.6.1.4.1.208.39.7.2.1.1 | ColumnpimCardNumber | read-only | mandatory | The card number in the cardTable that this PIM is inserted in. |
| 1.3.6.1.4.1.208.39.7.2.1.2 | ColumnpimNumber | read-only | mandatory | The number of the PIM. |
| 1.3.6.1.4.1.208.39.7.2.1.3 | ColumnpimId | read-only | mandatory | The product identification of the PIM. |
| 1.3.6.1.4.1.208.39.7.2.1.4 | ColumnpimFirstPort | read-only | mandatory | The portNumber of the first port on the PIM. |
| 1.3.6.1.4.1.208.39.7.2.1.5 | ColumnpimNumberOfPorts | read-only | mandatory | The number of ports on the PIM. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ProductIds | INTEGER { notAvailable(1), es-1520(1163072800), es-1530(1163072816), es-1810(1163073552), es-1820(1163073568), es-1830(1163073584), es-1831(1163073585), es-1832(1163073586), es-1840(1163073600), es-1850(1163073616), es100fx(1163073617), es10t24(1163076624), es10t24plus(1163076640), es10mmt12(1163076656), es10mmfl(1163076657), es-0012(1163067410), es-0040(1163067456), es-0100(1163067648), es-0101(1163067649), es100mmfx(1163067650), es-0103(1163067651), es100mmtx(1163067664), es-0111(1163067665), es-0154(1163067732), es-0155(1163067733), lp-3001(1280323585), lp-3002(1280323586), lp-3003(1280323587), lp-3004(1280323588), lp-3005(1280323589), lp-3006(1280323590), lp-3014(1280323604), lp-3015(1280323605) } |