FH800u-MIB
101 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress OBJECT-TYPE TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.207 | NodealliedTelesyn | |||
| 1.3.6.1.4.1.207.1 | Nodeproducts | |||
| 1.3.6.1.4.1.207.1.10 | NodedualHub | |||
| 1.3.6.1.4.1.207.1.10.1 | Nodefh812u | |||
| 1.3.6.1.4.1.207.1.10.2 | Nodefh824u | |||
| 1.3.6.1.4.1.207.8 | NodemibObject | |||
| 1.3.6.1.4.1.207.8.1 | NoderepeaterMib | |||
| 1.3.6.1.4.1.207.8.1.20 | NodenewRepeaterMib | |||
| 1.3.6.1.4.1.207.8.1.20.3 | NodeacctonHubMIB | |||
| 1.3.6.1.4.1.207.8.1.20.3.11 | NodeatactDualHubMgt | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1 | Nodefh800uIntrusionHappen | There were some intruders on some port in this system | ||
| 1.3.6.1.4.1.207.8.1.20.3.11.1 | Nodefh800uMgt | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1 | Nodefh800uBasicCapability | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1 | Nodefh800uStackInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.1 | ScalarstackInusedIP | read-only | mandatory | The IP address currently used by the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.2 | ScalarstackInusedNetMask | read-only | mandatory | The subnet maskcurrently used by the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.3 | ScalarstackInusedGateway | read-only | mandatory | The prefered gateway used to send traps. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.4 | ScalarstackInusedServerSlipAddr | read-only | mandatory | The Server SLIP addresscurrently used by the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.5 | ScalarstackInusedHostSlipAddr | read-only | mandatory | The Host SLIP address currently used by the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.6 | ScalarstackInusedBootUpIP | read-only | mandatory | The Bootup IP address currently used by the Dual-Speed Hub system. The Bootup IP must reside in the same subnet as the stackIP. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.7 | ScalarstackTemporalIP | read-write | mandatory | Used to change the IP address of the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.8 | ScalarstackTemporalNetMask | read-write | mandatory | Used to change the subnet mask of the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.9 | ScalarstackTemporalGateway | read-write | mandatory | Used to change the prefered gateway to send traps. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.10 | ScalarstackTemporalServerSlipAddr | read-write | mandatory | Used to change the Server SLIP address of the Dual-Speed Hub system. The SLIP address must reside in the same subnet as the stackIP. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.11 | ScalarstackTemporalHostSlipAddr | read-write | mandatory | Used to change the Host SLIP address of the Dual-Speed Hub system. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.12 | ScalarstackTemporalBootUpIP | read-write | mandatory | Used to change the Bootup IP address of the Dual-Speed Hub system. The Bootup IP must reside in the same subnet as the stackIP. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.13 | ScalaripInformationReset | read-write | mandatory | Setting the stackIP, stackNetMask,stackGateway, stackSlipAddr, and stackBootUpIP will not immediately enable parameters take effect . They will take effect whe… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.14 | ScalarstackHealthMonitor | read-only | mandatory | < FOR fh800u Dual-Speed Hub DEFINITION : > There are two kinds of hubs : 12 ports need (1+ 12 + 1 + 1 + 1 + 1 +1 +1 +1) 20 bytes and 24 ports need (1+ 24 + 1 +… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2 | Nodefh800uGroupInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1 | TablegroupTable | not-accessible | mandatory | A group means a hub unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1 | RowgroupEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.1 | ColumngroupID | read-only | mandatory | The ID number of a hub unit, used to select it |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.2 | ColumngroupType | read-only | mandatory | Type of hub unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.3 | ColumngroupCounterReset | read-write | mandatory | Write any value to this variable to reset the counters of the hub unit. 2 is a value commonly used to reset things |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.4 | ColumngroupPosition | read-only | mandatory | Physical position of a hub unit in top-down order, only supported if hardware permits such as Dual-Speed Hub systems |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.5 | ColumngroupRptrHwVer | read-only | mandatory | Hardware version of the repeater board. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.6 | ColumngroupRptrSerialNo | read-only | mandatory | Serial number of the repeater board. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.7 | ColumngroupSysMajorVer | read-only | mandatory | Microcode major version of this hub. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.8 | ColumngroupSysMinorVer | read-only | mandatory | Microcode minor version of this hub. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.9 | ColumngroupPostCodeMajorVer | read-only | mandatory | POST microcode major version of this hub. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.10 | ColumngroupPostCodeMinorVer | read-only | mandatory | POST microcode minor version of this hub. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.11 | ColumngroupAgentStatus | read-only | mandatory | Status of this hub agent. Each stack allows an SNMP primary agent. primary(2): The agent in this stack is a primary agent. backup(3): The agent in this stack i… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.12 | ColumngroupAgentHwVer | read-only | mandatory | Hardware version of the agent board. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.13 | ColumngroupAgentSerialNo | read-only | mandatory | Serial number of the agent board. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.14 | ColumngroupAgentPhysAddr | read-only | mandatory | MAC address of this hub agent |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.15 | ColumngroupAgentBootupOption | read-write | mandatory | This variable defines how to start the microcode in the segment. normal(1): Use NVRAM information and flash ROM microcode to start up the system. tftp-download… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.16 | ColumngroupAgentBaudrate | read-write | mandatory | Baud rate of the console port |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3 | Nodefh800uPortInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1 | TableportTable | not-accessible | mandatory | information about ports in a system. Each port belongs to a group. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1 | RowportEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.1 | ColumnportGroupID | read-only | mandatory | ID of the hub unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.2 | ColumnportID | read-only | mandatory | ID of the port unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.3 | ColumnportSpeed | read-only | mandatory | Ethernet connector type of a port |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.4 | ColumnportSpeedConfig | read-write | mandatory | Select the Ethernet connector type of a port |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.5 | ColumnportSegmtID | read-only | mandatory | ID of the Segment unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.4 | Nodefh800uSegmentInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5 | Nodefh800uRmonConfig | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.1 | ScalarnicAttachSegment | read-write | mandatory | The value represents the segment that the NIC is attached to. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.2 | ScalarfullRmonSegment | read-write | mandatory | The value shows if the segment supports all rmon or only 4 rmon groups. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3 | TablermonConfigTable | not-accessible | mandatory | RMON configuration table information; the index is the ID of of the segment the rmon montioring . |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3.1 | RowrmonConfigEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3.1.1 | ColumnrmonConfigSegmtID | read-only | mandatory | ID of the Segment rmon is montioring. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3.1.2 | ColumnrmonConfigStatus | read-write | mandatory | Status of this RMON segment. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2 | Nodefh800uPerfMonCapability | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3 | Nodefh800uPerfMonSegmentInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1 | TableperfMonSegmentTable | not-accessible | optional | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1 | RowperfMonSegmentEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.1 | ColumnsegmentPerfID | read-only | mandatory | ID used to select a segment |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.2 | ColumnsegmentCRCErrors | read-only | mandatory | Total CRC errors received by a segment. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.3 | ColumnsegmentAlignmentErrors | read-only | mandatory | Total frame alignment errors received by a segment |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.4 | ColumnsegmentCollisions | read-only | mandatory | Total collisions received in a segment |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.5 | ColumnsegmentTotalPortIsolates | read-only | mandatory | Total isolated ports in a segment. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.6 | ColumnsegmentSymbolErrors | read-only | mandatory | Total frame symbol errors received by a segment |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3 | Nodefh800uSwitchCapability | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1 | Nodefh800uSwitchStatsInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1 | TableswitchPortStatsTable | not-accessible | mandatory | This table provides statistics on each port on each switch module in the stack. Note that statistics for the external port on media and switch/media modules ar… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1 | RowswitchPortStatsEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.1 | ColumnswitchPortStatsGroupID | read-only | mandatory | The group ID of the switch module port being referenced. If the group is not present, or if there is no switch module installed in the group, GetRequests and S… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.2 | ColumnswitchPortStatsID | read-only | mandatory | The port ID of the switch module port being referenced. Port 1 is always the internal 100Mbps port. Port 2 is always the internal 10Mbps port. Port 3 is always… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.3 | ColumnswitchPortReadableFrames | read-only | mandatory | The number of valid frames received by the port. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.4 | ColumnswitchPortReadableOctets | read-only | mandatory | The number of octets (bytes) in all valid frames received by the port. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.5 | ColumnswitchPortFCSErrors | read-only | mandatory | The number of valid-length frames received by the port that had FCS (frame check sequence) errors. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.6 | ColumnswitchPortAlignmentErrors | read-only | mandatory | The number of valid-length frames received by the port that had alignment errors. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.7 | ColumnswitchPortFramesTooLong | read-only | mandatory | The number of frames received by the port that were longer than 1518 bytes. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.8 | ColumnswitchPortShortEvents | read-only | mandatory | The number of frames received by the port that were shorter than 82 bits. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.9 | ColumnswitchPortRunts | read-only | mandatory | The number of frames received by the port that were longer than 82 bits but shorter than 512 bits (64 bytes). |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.10 | ColumnswitchPortCollisions | read-only | mandatory | The number of collisions detected on the port. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.11 | ColumnswitchPortLateEvents | read-only | mandatory | The number of collisions detected on the port that occurred later than 512 bit-times into the transmission of a packet. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.12 | ColumnswitchPortVeryLongEvents | read-only | mandatory | The number of times any activity continued for more than 4 to 7.5 milliseconds. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.13 | ColumnswitchPortDataRateMismatches | read-only | mandatory | The number of times the incoming data rate mismatched the local clock source enough to cause a FIFO overflow or underflow. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.14 | ColumnswitchPortBroadcastPackets | read-only | mandatory | The number of good broadcast frames received by the port. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.15 | ColumnswitchPortMulticastPackets | read-only | mandatory | The number of good multicast (not broadcast) frames received by the port. |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5 | Nodefh800uSecurityCapability | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3 | Nodefh800uSecurityInfo | |||
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3 | TablesecurityPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1 | RowsecurityPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.1 | ColumnsecurityPortGroupID | read-only | mandatory | ID of a hub unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.2 | ColumnsecurityPortID | read-only | mandatory | Port ID in a hub unit |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.3 | ColumnsecurityPortAddr | read-write | mandatory | MAC address |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.5 | ColumnsecurityAutoLearnAction | read-write | mandatory | Setting this object to inactive(1) disables the auto-learn function for the physical address authorized access to this port. Once this object is set to active(… |
| 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.6 | ColumnsecurityPortIntrusion | read-write | mandatory | Set this variable to set function active or inactive |