Fibronics-EtherSwitch-MIB
68 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.22 | Nodefibronics | |||
| 1.3.6.1.4.1.22.100 | Nodeproducts | |||
| 1.3.6.1.4.1.22.100.9 | Nodeeth-switch | |||
| 1.3.6.1.4.1.22.100.9.3 | Nodexm516-card | |||
| 1.3.6.1.4.1.22.100.9.4 | Nodexm517-card | |||
| 1.3.6.1.4.1.22.100.9.5 | Nodexm518-card | |||
| 1.3.6.1.4.1.22.100.9.6 | Nodexm519-card | |||
| 1.3.6.1.4.1.22.100.9.7 | Nodexm5110-card | |||
| 1.3.6.1.4.1.22.100.9.8 | Nodexm5111-card | |||
| 1.3.6.1.4.1.22.100.9.9 | Nodexm5112-card | |||
| 1.3.6.1.4.1.22.100.9.10 | Nodexm5113-card | |||
| 1.3.6.1.4.1.22.100.9.11 | Nodexm5114-card | |||
| 1.3.6.1.4.1.22.100.9.12 | Nodexm5115-card | |||
| 1.3.6.1.4.1.22.101 | Nodemibs | |||
| 1.3.6.1.4.1.22.101.9 | Nodemibsbridges | |||
| 1.3.6.1.4.1.22.101.9.1 | Nodemibbridges-specific | |||
| 1.3.6.1.4.1.22.101.9.1.2 | Nodemibeth2eth | |||
| 1.3.6.1.4.1.22.101.9.1.2.1 | Nodemib-eps | |||
| 1.3.6.1.4.1.22.101.9.1.2.1.1 | NodefibEsObjects | |||
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1 | NodefibEsMain | |||
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1 | NodefibEsConfig | |||
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.1 | ScalarfibEsFwVer | read-only | mandatory | The firmware version in the form major.minor. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.2 | ScalarfibEsHwVer | read-only | mandatory | The hardware version in the form major.minor. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.3 | ScalarfibEsIpAddr | read-write | mandatory | The administrative value of the IP address. The current operational IP address can be obtained by the ipAdEntAddr entry in the ipAddrTable. This parameter will… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.4 | ScalarfibEsNetMask | read-write | mandatory | The administrative value of the subnet mask. The current operational subnet mask can be obtained by the ipAdEntNetMask entry in the ipAddrTable. This parameter… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.5 | ScalarfibEsDefaultGateway | read-write | mandatory | The administrative value of the default gateway (router) IP address. The current operational default gateway's IP address can be obtained from the ipRouteTable… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.6 | ScalarfibEsTrapRcvrMaxEnt | read-only | mandatory | The maximum number of rows in the trap receiver table. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.7 | ScalarfibEsTrapRcvrCurEnt | read-only | mandatory | The current number of rows in the trap receiver table. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.8 | ScalarfibEsTrapRcvrNext | read-only | mandatory | The index of the next available row to be created in the trap receiver table. A value of zero means that the table is full and no more rows can be added. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9 | TablefibEsTrapRcvrTable | not-accessible | mandatory | A table of managers to which to send traps. Entries in the table are saved across resets and power cycles. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1 | RowfibEsTrapRcvrEntry | not-accessible | mandatory | Definition of rows in the trap receiver table. The column fibEsTrapRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with … |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.1 | ColumnfibEsTrapRcvrIndex | read-only | mandatory | The index of the row in the table. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.2 | ColumnfibEsTrapRcvrStatus | read-write | mandatory | Setting this object to the value invalid(3) deletes the row from the table. The value invalid(3) should never be returned on a GET. The value of create(4) on a… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.3 | ColumnfibEsTrapRcvrIpAddress | read-write | mandatory | IP address for an SNMP manager that is to receive the trap. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.4 | ColumnfibEsTrapRcvrComm | read-write | mandatory | Community string to use. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2 | NodefibEsSys | |||
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.1 | ScalarfibEsNumPorts | read-only | mandatory | The maximum number of ports on the switch. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.2 | ScalarfibEsNumStations | read-only | mandatory | Aggregate number of currently active stations (nodes) on all ports on the switch. This is the value from the system module. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.3 | ScalarfibEsMostStations | read-only | mandatory | Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle. This is the value as seen by the system module. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.4 | ScalarfibEsMaxStations | read-only | mandatory | Highest aggregate number of stations which the switch can support simultaneously. (This is the maximum number that the system module can support.) |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.5 | ScalarfibEsReset | read-write | mandatory | This object is used to reset the switch. Writing softReset(3) causes the switch to reset the hardware, run quick diagnostics, clear all counters, start switchi… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.6 | ScalarfibEsNumResets | read-only | mandatory | Number of soft resets the switch has executed since the last hard reset or power cycle. Soft resets are defined as writing softReset(3) to fibEsReset, pressing… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.7 | ScalarfibEsAddrAgingTime | read-write | mandatory | Number of minutes of inactivity before an address entity is aged out. A value of zero means no aging. Note: if an address shows up on another port, the origina… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9 | TablefibEsSysStaTable | not-accessible | mandatory | A table of station addresses from all ports known to the system module. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1 | RowfibEsSysStaEntry | not-accessible | mandatory | Definition of the rows in the system module station address table. Rows can not be created or deleted via SNMP requests. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1.1 | ColumnfibEsSysStaMacAddr | read-only | mandatory | The Station's MAC address. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1.2 | ColumnfibEsSysStaPort | read-only | mandatory | The source port for the Station. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1.3 | ColumnfibEsSysStaTraffic | read-only | mandatory | A bit string that identifies with value of one of the ports that this station has generated traffic to or from. The bits are numbered starting at zero, with bi… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2 | NodefibEsPort | |||
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1 | TablefibEsPortTable | not-accessible | mandatory | A table of information about each port. The number of rows is given by fibEsNumPorts. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1 | RowfibEsPortEntry | not-accessible | mandatory | Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of fibEsNumPorts. Rows can not be created … |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.1 | ColumnfibEsPortIndex | read-only | mandatory | A unique value for each port entry. The value corresponds the port number. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.2 | ColumnfibEsPortOprStatus | read-write | mandatory | The operational status of the port. Setting to enabled(1) enables the port. Setting to disabled(2) disables the port. The value is saved across resets and powe… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.3 | ColumnfibEsPortDuplex | read-only | mandatory | Indicates whether the port is jumper configured for full or half duplex operation. Note: internal connected ports are always halfDuplex(2). |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.4 | ColumnfibEsPortRcvLocalFrames | read-only | mandatory | Number of frames received where the destination is on this port. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.5 | ColumnfibEsPortForwardedFrames | read-only | mandatory | Number of frames received on this port and forwarded to another port or the system module for processing. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.6 | ColumnfibEsPortMostStations | read-only | mandatory | Highest number of stations ever active at any time since the last reset of the switch as seen by this port. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.7 | ColumnfibEsPortMaxStations | read-only | mandatory | Maximum number of stations which the port can support simultaneously. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.8 | ColumnfibEsPortSWHandledFrames | read-only | mandatory | Number of Frames received on this port and delivered to the system module for processing. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.9 | ColumnfibEsPortLocalStations | read-only | mandatory | Number of stations on this port's address table which belong to the segment attached to this port. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.10 | ColumnfibEsPortRemoteStations | read-only | mandatory | Number of stations on this port's address table which belong to segments attached to other ports. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.11 | ColumnfibEsPortUnknownStaFrames | read-only | mandatory | Number of unicast frames received on this port and forwarded to the system module for processing because the source or destination station address is not in th… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.12 | ColumnfibEsPortResetStats | read-write | mandatory | Setting this object to reset(3) causes all traffic counters for this port to be set to zero. Also the value of fibEsPortResetTimer is set to zero. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.13 | ColumnfibEsPortResetTimer | read-only | mandatory | Time (in 100th second ticks) since the port counters were reset. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.14 | ColumnfibEsPortResetAddrs | read-write | mandatory | Setting this object to reset(3) clears all address table entries for this port as well as setting all port traffic counters to zero and setting fibEsPortResetT… |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.15 | ColumnfibEsPortRcvBcasts | read-only | mandatory | Number of Broadcast Frames received on this port without errors. |
| 1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.16 | ColumnfibEsPortSwitchedFrames | read-only | mandatory | Number of frames switched on this port |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| MacAddr | OCTET STRING (SIZE(6)) |