GIGAswitchEthernet-MIB
368 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress NetworkAddress TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.36 | Nodedec | |||
| 1.3.6.1.4.1.36.2 | Nodeema | |||
| 1.3.6.1.4.1.36.2.18 | Nodemib-extensions-1 | |||
| 1.3.6.1.4.1.36.2.18.39 | NodegsEMIB | |||
| 1.3.6.1.4.1.36.2.18.39.1 | NodegsEAgent | |||
| 1.3.6.1.4.1.36.2.18.39.1.1 | NodegsEAgentGen | |||
| 1.3.6.1.4.1.36.2.18.39.1.1.1 | ScalargsEAgentMIBVersion | read-only | mandatory | The version of the Digital Equipment Corporation GIGAswitch\Ethernet Enterprise Specific MIB that this agent supports. |
| 1.3.6.1.4.1.36.2.18.39.1.1.2 | ScalargsEAgentMgrIndex | read-only | mandatory | The value of this object represents the index into the community table that is used to authenticate SNMP requests for this manager. |
| 1.3.6.1.4.1.36.2.18.39.1.2 | NodegsEAgentCommunity | |||
| 1.3.6.1.4.1.36.2.18.39.1.2.1 | TablegsECommunityTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1 | RowgsECommunityEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.1 | ColumngsECommunityIndex | read-only | mandatory | An index that uniquely identifies this entry. |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.2 | ColumngsECommunityString | read-write | mandatory | The community string included in the SNMP PDU used for authentication purposes. |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.3 | ColumngsECommunityAddressType | read-write | mandatory | The type of address associated with this community. If set to any(1), only the community string is authenticated. |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.4 | ColumngsECommunityAddress | read-write | mandatory | If the address type is any, then the value of this object is a null string. If the type is ipv4(2), then this value represents a 4 byte IP address. |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.5 | ColumngsECommunityAccess | read-write | mandatory | The MIB access supported for this community entry. A Get or GetNext SNMP PDU is authenticated if the value of this object is read-only(2) or read-write(3). A S… |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.6 | ColumngsECommunityTrapReceiver | read-write | mandatory | If set to enable(1), this community entry is considered a trap receiver. When the agent generates an SNMP trap, a copy will be sent to this host using this com… |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.7 | ColumngsECommunitySecurityLevel | read-write | mandatory | Secure tables are only accessible from users with security clearance. For example, this table (the community table) is only accessible by parties that have the… |
| 1.3.6.1.4.1.36.2.18.39.1.2.1.1.8 | ColumngsECommunityStatus | read-write | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.1.3 | NodegsEAgentWeb | |||
| 1.3.6.1.4.1.36.2.18.39.1.3.1 | ScalargsEAgentWebServerURL | read-write | mandatory | The URL of where the document server software is installed. The switch uses this location to find online help and bimapped graphics. Enter the host name or IP … |
| 1.3.6.1.4.1.36.2.18.39.1.3.2 | ScalargsEAgentWebServerHelpDirectory | read-write | mandatory | The subdirectory that contains the help files on the document server. Typically, this directory is 'help'. |
| 1.3.6.1.4.1.36.2.18.39.3 | NodegsEChassis | |||
| 1.3.6.1.4.1.36.2.18.39.3.1 | NodegsEChassisGen | |||
| 1.3.6.1.4.1.36.2.18.39.3.1.1 | ScalargsEChassisType | read-only | mandatory | The model of the chassis that this agent is managing. |
| 1.3.6.1.4.1.36.2.18.39.3.1.2 | ScalargsEChassisSlots | read-only | mandatory | The number of slots available in this chassis. If this chassis is a stackable chassis, the total capacity of stacking units. |
| 1.3.6.1.4.1.36.2.18.39.3.2 | NodegsEInventory | |||
| 1.3.6.1.4.1.36.2.18.39.3.2.1 | TablegsEInventoryTable | not-accessible | mandatory | A table of inventory information. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1 | RowgsEInventoryEntry | not-accessible | mandatory | Inventory information related to this device. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.1 | ColumngsEInventoryResourceType | read-only | mandatory | The resource class of this inventory item. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.2 | ColumngsEInventoryResourceIndex | read-only | mandatory | The resource identifier of this inventory item. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.3 | ColumngsEInventoryModelNumber | read-only | mandatory | The model number of this device. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.4 | ColumngsEInventorySerialNumber | read-only | mandatory | The serial number of this device. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.5 | ColumngsEInventoryVersion | read-only | mandatory | The revision number of this device. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.6 | ColumngsEInventoryManufactureInfo | read-only | mandatory | Information related to the manufacturing of this device. |
| 1.3.6.1.4.1.36.2.18.39.3.2.1.1.7 | ColumngsEInventoryScratchPad | read-write | mandatory | A scratch pad area available for keeping user-supplied inventory information. |
| 1.3.6.1.4.1.36.2.18.39.3.3 | NodegsEPowerSystems | |||
| 1.3.6.1.4.1.36.2.18.39.3.3.1 | NodegsEPowerSupplies | |||
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1 | TablegsEPowerSupplyTable | not-accessible | mandatory | A table of information related to each power supply in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1 | RowgsEPowerSupplyEntry | not-accessible | mandatory | An entry providing information about a particular power supply in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1.1 | ColumngsEPowerSupplyIndex | read-only | mandatory | An index that uniquely identifies this power supply. This index corresponds to the gsEResourceIndex of the power supply type resource. |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1.2 | ColumngsEPowerSupplyType | read-only | mandatory | An enumerated integer describing the type of power supply. |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1.3 | ColumngsEPowerSupplyStatus | read-only | mandatory | The status of this power supply. Okay(1) indicates the power supply is operating properly. Faulty(2) indicates that the power supply is not functioning properl… |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1.4 | ColumngsEPowerSupplyInputStatus | read-only | mandatory | The status of the input power feed (e.g. the AC power cord) to this power supply. |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1.5 | ColumngsEPowerSupplyOutputStatus | read-only | mandatory | The status of the output power from this power supply. |
| 1.3.6.1.4.1.36.2.18.39.3.3.1.1.1.6 | ColumngsEPowerSupplyOutputCapacity | read-only | mandatory | The total capacity of power supplied by this supply in Watts. |
| 1.3.6.1.4.1.36.2.18.39.3.3.2 | NodegsEPowerMgmtGen | |||
| 1.3.6.1.4.1.36.2.18.39.3.3.2.1 | ScalargsEPowerCapacity | read-only | mandatory | The total capacity (in Watts) of power available (currently) in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.3.2.2 | ScalargsEPowerUsed | read-only | mandatory | The total power (in Watts) currently being consumed in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.3.3 | NodegsEPowerMgmtCtl | |||
| 1.3.6.1.4.1.36.2.18.39.3.3.3.1 | TablegsEPowerControlTable | not-accessible | mandatory | This table manages the power attributes associated with each module. |
| 1.3.6.1.4.1.36.2.18.39.3.3.3.1.1 | RowgsEPowerControlEntry | not-accessible | mandatory | An entry in the power control table manages the power attributes of the specified module. |
| 1.3.6.1.4.1.36.2.18.39.3.3.3.1.1.1 | ColumngsEPowerControlUsed | read-only | mandatory | The total power (in Watts) used by this module. |
| 1.3.6.1.4.1.36.2.18.39.3.3.3.1.1.2 | ColumngsEPowerControlPriority | read-write | mandatory | The priority of this module to be considered in the event of a power supply failure where the amount of power used exceeds the system capacity. Low priority mo… |
| 1.3.6.1.4.1.36.2.18.39.3.3.3.1.1.3 | ColumngsEPowerControlMode | read-write | mandatory | Normally, a module power mode is enable(1). In the event of a power supply failure resulting in a power shortage, or in the event of this module being inserted… |
| 1.3.6.1.4.1.36.2.18.39.3.4 | NodegsETemperature | |||
| 1.3.6.1.4.1.36.2.18.39.3.4.1 | TablegsETempTable | not-accessible | mandatory | A table of information related to the temperature within the system. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1 | RowgsETempEntry | not-accessible | mandatory | An entry providing temperature information related to a specific temperature probe in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1.1 | ColumngsETempIndex | read-only | mandatory | A unique index that identifies this temperature probe. This index corresponds to the gsEResourceIndex for temperature probe type resources. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1.2 | ColumngsETempValue | read-only | mandatory | The current temperature reading of this temperature probe in degrees Celsius. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1.3 | ColumngsETempUpperLimit | read-write | mandatory | The upper temperature limit of this temperature probe in degrees Celsius. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1.4 | ColumngsETempUpperWarning | read-write | mandatory | The upper temperature warning of this temperature probe in degrees Celsius. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1.5 | ColumngsETempLowerWarning | read-write | mandatory | The lower temperature warning of this temperature probe in degrees Celsius. |
| 1.3.6.1.4.1.36.2.18.39.3.4.1.1.6 | ColumngsETempLowerLimit | read-write | mandatory | The lower temperature limit of this temperature probe in degrees Celsius. |
| 1.3.6.1.4.1.36.2.18.39.3.5 | NodegsEModules | |||
| 1.3.6.1.4.1.36.2.18.39.3.5.1 | TablegsEModuleTable | not-accessible | mandatory | A table of information related to the modules in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1 | RowgsEModuleEntry | not-accessible | mandatory | Attributes related to managing this module. |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.1 | ColumngsEModuleIndex | read-only | mandatory | An index that uniquely identifies this module. This index corresponds to the gsEResourceIndex associated with module type resources. |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.2 | ColumngsEModuleName | read-write | mandatory | A user-assignable name for this module. |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.3 | ColumngsEModuleType | read-only | mandatory | An enumerated integer that is unique for each module model. |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.4 | ColumngsEModuleBaseType | read-only | mandatory | The base type of this module. This object is used to describe the core functions of the module. Often, base designs are derived into multiple module types whic… |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.5 | ColumngsEModuleSlotWidth | read-only | mandatory | The number of slots that this module occupies. |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.6 | ColumngsEModuleSlotOffset | read-only | mandatory | The slot offset (one based) that identifies, along with the slot width and slot location, the actual slots that this module occupies. The offset identifies whi… |
| 1.3.6.1.4.1.36.2.18.39.3.5.1.1.7 | ColumngsEModulePorts | read-only | mandatory | The total number of ports associated with this module. |
| 1.3.6.1.4.1.36.2.18.39.3.6 | NodegsEPorts | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.1 | NodegsEPortMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1 | TablegsEPortTable | not-accessible | mandatory | A table of information related to every data port in this data networking system. |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1 | RowgsEPortEntry | not-accessible | mandatory | A data port associated with this data networking system. |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.1 | ColumngsEPortIndex | read-only | mandatory | An index that uniquely identifies this port. Typically, ports are child resources of the module that contains them. In these cases, ports are identified by the… |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.2 | ColumngsEPortName | read-write | mandatory | The user-assigned name for this port. Note that setting this object for an internal(1) port results in an error. |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.3 | ColumngsEPortType | read-only | mandatory | An internal(1) port does not have an external connection. An ether-ten-oneHundred(2) port is an Ethernet port which can be switched between 10 and 100 megabits… |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.4 | ColumngsEPortBaseType | read-only | mandatory | The base type of this port. This object may be useful to help manage new port types that are similar in nature to legacy port types. |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.5 | ColumngsEPortMode | read-write | mandatory | The mode of this port. When set to enable(1), this port passes data. When set to disable(2), the port does not receive or transmit data, nor does it generate p… |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.6 | ColumngsEPortStatus | read-only | mandatory | The status of this port. Disabled(1) means that this port has been disabled through management action. Okay(2) indicates that this port is operating properly. … |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.7 | ColumngsEPortConnector | read-only | mandatory | The connector type associated with this port. |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.8 | ColumngsEPortSpeedState | read-only | mandatory | The data rate of this port in bits per second. For example, a standard Ethernet port (e.g. 10BASE-T) would indicate a value of ten-megabits-per-second((1) indi… |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.9 | ColumngsEPortDuplexState | read-only | mandatory | The value of this object indicates whether this port is operating in full- or half-duplex mode. The value under-negotiation(3) indicates that the port has not … |
| 1.3.6.1.4.1.36.2.18.39.3.6.1.1.1.10 | ColumngsEPortGroupBinding | read-only | mandatory | Each port is associated with a port group. Typically, a port will belong to a port group of one and the value of this object will be the same as the port index… |
| 1.3.6.1.4.1.36.2.18.39.3.6.2 | NodegsEPortFlowControlMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.2.1 | TablegsEPortFlowControlTable | not-accessible | mandatory | A table of ports that support flow control. |
| 1.3.6.1.4.1.36.2.18.39.3.6.2.1.1 | RowgsEPortFlowControlEntry | not-accessible | mandatory | Configuration objects related to port based flow control. |
| 1.3.6.1.4.1.36.2.18.39.3.6.2.1.1.21 | ColumngsEPortFlowControlMode | read-write | mandatory | Flow control is used to prevent or reduce the dropping of frames due to the lack of buffer space. Overall, networks are more efficient when a sending station i… |
| 1.3.6.1.4.1.36.2.18.39.3.6.3 | NodegsEPortDuplexMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.3.1 | TablegsEPortDuplexTable | not-accessible | mandatory | A table of ports that support full- and half-duplex data communications. |
| 1.3.6.1.4.1.36.2.18.39.3.6.3.1.1 | RowgsEPortDuplexEntry | not-accessible | mandatory | A port device configuration that controls the duplex mode of this port. |
| 1.3.6.1.4.1.36.2.18.39.3.6.3.1.1.31 | ColumngsEPortDuplexMode | read-write | mandatory | A point-to-point Ethernet port may be configured to support half or full duplex communications. A full-duplex(2) port transmits and receives data concurrently,… |
| 1.3.6.1.4.1.36.2.18.39.3.6.4 | NodegsEPortSpeedMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.4.1 | TablegsEPortSpeedTable | not-accessible | mandatory | A table of port devices that support multiple speeds. |
| 1.3.6.1.4.1.36.2.18.39.3.6.4.1.1 | RowgsEPortSpeedEntry | not-accessible | mandatory | A port that supports multiple speeds. |
| 1.3.6.1.4.1.36.2.18.39.3.6.4.1.1.41 | ColumngsEPortSpeedMode | read-write | mandatory | Some of these values may not be applicable to certain types of ports. This object indicates the desired data rate of this port. If auto-negotiation is turned o… |
| 1.3.6.1.4.1.36.2.18.39.3.6.5 | NodegsEPortAutoNegotiationMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.5.1 | TablegsEPortAutoNegotiationTable | not-accessible | mandatory | A table of ports that support auto-negotiation. |
| 1.3.6.1.4.1.36.2.18.39.3.6.5.1.1 | RowgsEPortAutoNegotiationEntry | not-accessible | mandatory | Attributes associated with a port that supports auto-negotiation. |
| 1.3.6.1.4.1.36.2.18.39.3.6.5.1.1.51 | ColumngsEPortAutoNegotiationMode | read-write | mandatory | Setting this object to autoNegotiate(1) causes this port to negotiate the duplex mode and the port speed, subject to the port's capabilities. |
| 1.3.6.1.4.1.36.2.18.39.3.6.5.1.1.52 | ColumngsEPortAutoNegotiationSpeedAdvertisement | read-write | mandatory | The speed to advertise while auto-negotiating. |
| 1.3.6.1.4.1.36.2.18.39.3.6.5.1.1.53 | ColumngsEPortAutoNegotiationDuplexAdvertisement | read-write | mandatory | The duplexity to advertise while auto-negotiating. |
| 1.3.6.1.4.1.36.2.18.39.3.6.6 | NodegsEPortRateLimitMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.6.1 | TablegsEPortRateLimitTable | not-accessible | mandatory | A table of ports that support the ability to limit the rate of floods. |
| 1.3.6.1.4.1.36.2.18.39.3.6.6.1.1 | RowgsEPortRateLimitEntry | not-accessible | mandatory | The rate limit configuration associated with this port. |
| 1.3.6.1.4.1.36.2.18.39.3.6.6.1.1.61 | ColumngsEPortRateLimitMode | read-write | mandatory | This object configures whether rate limiting is enabled for this port (the factory default is enable(1)). Enabling rate limiting for this port prevents floods … |
| 1.3.6.1.4.1.36.2.18.39.3.6.6.1.1.62 | ColumngsEPortRateLimitRate | read-write | mandatory | The percentage of the port's transmitted data allowed to be floods (or floods and known multicasts). For example, the factory default setting of twenty-percent… |
| 1.3.6.1.4.1.36.2.18.39.3.6.6.1.1.63 | ColumngsEPortRateLimitBurstSize | read-write | mandatory | The maximum number of consecutive transmitted flooded (or flooded and known multicasted) packets. Typically, the burst size is set so as to not overflow the po… |
| 1.3.6.1.4.1.36.2.18.39.3.6.8 | NodegsEPortCategoryMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.6.8.1 | TablegsEPortCategoryTable | not-accessible | mandatory | A table of ports that support the port category feature. Currently, all ports support this capability. |
| 1.3.6.1.4.1.36.2.18.39.3.6.8.1.1 | RowgsEPortCategoryEntry | not-accessible | mandatory | A port that supports port categorization. |
| 1.3.6.1.4.1.36.2.18.39.3.6.8.1.1.81 | ColumngsEPortCategoryMode | read-write | mandatory | By default, all ports are considered service ports. A service port is a port that provides a networks service such as a connection to a server, other switches,… |
| 1.3.6.1.4.1.36.2.18.39.3.7 | NodegsEBufferMgt | |||
| 1.3.6.1.4.1.36.2.18.39.3.7.1 | TablegsEBufferTable | not-accessible | mandatory | A table of frame buffers in the system. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1 | RowgsEBufferEntry | not-accessible | mandatory | Objects related to the management of this frame buffer. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.1 | ColumngsEBufferIndex | read-only | mandatory | The unique index that identifies this buffer within the system. Buffers are indexed first by their module association and then a unique index within that modul… |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.2 | ColumngsEBufferFabricPort | read-only | mandatory | The switch fabric port associated with this buffer. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.3 | ColumngsEBufferFabricPortDirection | read-only | mandatory | The value of this object indicates whether the buffer is used for buffering frames going into the switching fabric or coming out of the fabric. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.4 | ColumngsEBufferSwitchPort | read-only | mandatory | The switch port associated with this frame buffer. Some buffers are not associated with any one switch port. In those cases, the value of the resource ID retur… |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.5 | ColumngsEBufferMemory | read-only | mandatory | The amount of memory available for frame buffering in Kilobytes (KB). |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.6 | ColumngsEBufferAgeTimer | read-write | mandatory | Configures the timer used for aging frames in this buffer. If the timer expires for a frame, the frame is dropped and the event is counted in the stale drop co… |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.7 | ColumngsEBufferPriorityServicing | read-write | mandatory | The value of this object configures how often the normal priority queue is serviced relative to the high priority queue. By default, the normal priority queue … |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.8 | ColumngsEBufferPriorityAllocation | read-write | mandatory | This object controls how much of the total buffer space should be allocated to high priority queue. Please be warned that setting this object to a different va… |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.9 | ColumngsEBufferPriorityThreshold | read-write | mandatory | This object configures the threshold for which frames are considered high priority. Frames may have a priority classification ranging from 0-7, 7 being the hig… |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.10 | ColumngsEBufferCongestion | read-only | mandatory | This object indicates whether this buffer is in a congested state.. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.11 | ColumngsEBufferHighOverflowDrops | read-only | mandatory | The count of the number of high priority frames dropped due to the high priority queue overflowing. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.12 | ColumngsEBufferLowOverflowDrops | read-only | mandatory | The count of the number of low priority frames dropped due to the low priority queue overflowing. |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.13 | ColumngsEBufferHighStaleDrops | read-only | mandatory | The count of the number of high priority frames dropped due to being in the high priority queue too long (the frame aged out). |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.14 | ColumngsEBufferLowStaleDrops | read-only | mandatory | The count of the number of low priority frames dropped due to being in the low priority queue too long (the frame aged out). |
| 1.3.6.1.4.1.36.2.18.39.3.7.1.1.16 | ColumngsEBufferCongestionDrops | read-only | mandatory | The count of the number of frames dropped due to the destination (output) buffer being congested. |
| 1.3.6.1.4.1.36.2.18.39.5 | NodegsESwitching | |||
| 1.3.6.1.4.1.36.2.18.39.5.1 | NodegsESwitchingLayerII | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.1 | NodegsESwitchGen | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.1.1 | ScalargsESwitchSTPConfig | read-write | mandatory | When set to ieee8021dStp(1), the switch executes spanning tree conformant to the IEEE 802.1D bridging standard. The switch runs one instance of spanning tree. … |
| 1.3.6.1.4.1.36.2.18.39.5.1.1.2 | ScalargsESwitchAgingTime | read-write | mandatory | The timeout period in seconds for aging dynamically learned forwarding information. A default of 300 seconds is recommended. An aged entry is marked invalid, b… |
| 1.3.6.1.4.1.36.2.18.39.5.1.1.3 | ScalargsESwitchSuperAgingTime | read-write | mandatory | The timeout period in days for removing stale invalid entries from the Address Forwarding Table. A superaged entry is removed completely from the Address Forwa… |
| 1.3.6.1.4.1.36.2.18.39.5.1.2 | NodegsEBridgeMgmt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1 | TablegsEBridgeTable | not-accessible | mandatory | A table of Spanning Tree information for every bridge in the system. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1 | RowgsEBridgeEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.1 | ColumngsEBridgeIndex | read-only | mandatory | An index that uniquely identifies this bridge. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.2 | ColumngsEBridgeType | read-only | mandatory | Indicates whether this is a legacy dot1d bridge consisting of all switch ports or a virtual bridge consisting of all virtual subports for a particular Vlan. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.3 | ColumngsEBridgeMode | read-write | mandatory | Used to enable or disable Spanning Tree for this bridge. When set to disable(2), all BPDUs are forwarded like regular multicast packets. The default value is e… |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.4 | ColumngsEBridgeStatus | read-only | mandatory | The enable/disable status of this bridge. This object incorporates the setting of the gsESwitchSTPConfig object. When gsESwitchSTPConfig is set such that this … |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.5 | ColumngsEBridgeStpPriority | read-write | mandatory | The priority value of the Bridge Identifier. See dot1dStpPriority. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.6 | ColumngsEBridgeStpTimeSinceTopologyChange | read-only | mandatory | The time since the last topology change was detected. See dot1dStpTimeSinceTopologyChange. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.7 | ColumngsEBridgeStpTopChanges | read-only | mandatory | The total number of topology changes. See dot1dStpTopChanges |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.8 | ColumngsEBridgeStpDesignatedRoot | read-only | mandatory | The bridge considered to be root by this node. See dot1dStpDesignatedRoot. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.9 | ColumngsEBridgeStpRootCost | read-only | mandatory | The cost of the path to the root from this node. See dot1dStpRootCost. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.10 | ColumngsEBridgeStpRootPort | read-only | mandatory | The port number with the lowest cost path to the root bridge. See dot1dStpRootPort. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.11 | ColumngsEBridgeStpMaxAge | read-only | mandatory | The maximum age used by this bridge to hold onto STP information before discarding. See dot1dStpMaxAge. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.12 | ColumngsEBridgeStpHelloTime | read-only | mandatory | The amount of time between configuration BPDUs. See dot1dStpHelloTime. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.13 | ColumngsEBridgeStpHoldTime | read-only | mandatory | The time value that indicates the interval during which no more than two configuration BPDUs will be sent by this node. See dot1dStpHoldTime. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.14 | ColumngsEBridgeStpForwardDelay | read-only | mandatory | The amount of time that this node stays in each of the Listening and Learning states. See dot1dStpForwardDelay. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.15 | ColumngsEBridgeStpBridgeMaxAge | read-write | mandatory | The value of MaxAge when this bridge is the root. See dot1dStpBridgeMaxAge. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.16 | ColumngsEBridgeStpBridgeHelloTime | read-write | mandatory | The value of HelloTime to use when this bridge is the root. See dot1dStpBridgeHelloTime. |
| 1.3.6.1.4.1.36.2.18.39.5.1.2.1.1.17 | ColumngsEBridgeStpBridgeForwardDelay | read-write | mandatory | The value of FowardDelay to use when this bridge is the root. See dot1dStpBridgeForwardDelay. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3 | NodegsEBridgePortMgmt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1 | TablegsEBridgePortTable | not-accessible | mandatory | A table of Spanning Tree information for every port that supports Spanning Tree in every bridge in the system |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1 | RowgsEBridgePortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.1 | ColumngsEBridgePortIndex | read-only | mandatory | An index that uniquely identifies this bridge port. This index corresponds to the gsEResourceIndex for bridge port type resources. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.2 | ColumngsEBridgePortPriority | read-write | mandatory | The value of the priority field in the port ID. See dot1dStpPortPriority. The default value is 128. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.3 | ColumngsEBridgePortState | read-only | mandatory | The port's current state as defined by the Spanning Tree Protocol. See dot1dStpPortState. The virtual port is considered broken if its switch port is blocked. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.4 | ColumngsEBridgePortEnable | read-write | mandatory | The enabled/disabled status of this port. See dot1dStpPortEnable. The default is enabled(2). |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.5 | ColumngsEBridgePortPathCost | read-write | mandatory | The contribution of this port to the path cost of the paths towards the spanning tree root. See dot1dStpPortPathCost. The default value is dependent on the por… |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.6 | ColumngsEBridgePortDesignatedRoot | read-only | mandatory | The bridge recorded as root for this port's segment. See dot1dStpPortDesignatedRoot. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.7 | ColumngsEBridgePortDesignatedCost | read-only | mandatory | The path cost of the designated root of the segment connected to this port. See dot1dStpPortDesignatedCost. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.8 | ColumngsEBridgePortDesignatedBridge | read-only | mandatory | The bridge identifier of the bridge that is considered the designated bridge for this port's segment. See dot1dStpPortDesignatedBridge. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.9 | ColumngsEBridgePortDesignatedPort | read-only | mandatory | The port identifier of the port on the Designated Bridge for this port's segment. See dot1dStpPortDesignatedPort. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.10 | ColumngsEBridgePortForwardTransitions | read-only | mandatory | The number of times this port has transitioned from the learning state to the forwarding state. See dot1dStpPortForwardTransitions. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.11 | ColumngsEBridgePortFastStart | read-write | deprecated | This object is being replaced by the switch port object gsESwitchPortFastStart. When this bridge port object is set to enable(1), the bridge port and all other… |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.12 | ColumngsEBridgePortSetDefault | read-write | mandatory | When set to setDefault(2), the gsEBridgePortPriority, gsEBridgePortEnable, and gsEBridgePortPathCost will be set to the factory default values. |
| 1.3.6.1.4.1.36.2.18.39.5.1.3.1.1.13 | ColumngsEBridgePortEnableChangeDetection | read-write | mandatory | When this object is set to enable(1), a Topology Change Notification will be generated when this port goes to Blocking or Forwarding (if the port is a designat… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4 | NodegsEL2AddrMgmt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1 | NodegsEL2AddrDatabaseMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1 | TablegsEL2AddressTable | not-accessible | mandatory | A table of address table entries. The address table is used by the bridging function to perform forwarding and filtering decisions. An address may appear multi… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1 | RowgsEL2AddressEntry | not-accessible | mandatory | A particular address table entry. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.1 | ColumngsEL2AddressIndex | read-only | mandatory | An index that uniquely identifies this address entry. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.2 | ColumngsEL2AddressTableIndex | read-only | mandatory | The address table that this entry is associated with. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.3 | ColumngsEL2AddressMacAddress | read-only | mandatory | The IEEE 802 MAC Address associated with this database entry. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.4 | ColumngsEL2AddressPortBinding | read-write | mandatory | The switch port that this address is associated with. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.5 | ColumngsEL2AddressBindingValid | read-only | mandatory | The port binding of an address entry is aged out in conformance with the specifications laid out in the IEEE 802.1D standard. When the address is aged out, the… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.6 | ColumngsEL2AddressVlanID | read-only | mandatory | The VLAN ID of the VLAN that this address entry corresponds to. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.7 | ColumngsEL2AddressPriority | read-write | mandatory | If set to high(2), frames destined to this address are classified with priority value 4. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.8 | ColumngsEL2AddressForward | read-only | mandatory | When set to specialDelivery(2), frames sent to this address are treated to special delivery where the spanning tree state of the inbound port is ignored. Typic… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.9 | ColumngsEL2AddressCopy | read-only | mandatory | It is sometimes useful for the switch processor to eavesdrop on traffic to certain destinations. This is especially useful in supporting the intelligent multic… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.10 | ColumngsEL2AddressPersistence | read-write | mandatory | This object indicates the persistence of this entry: other(1) - This entry is currently in use but the conditions under which it will remain so are different f… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.1.1.1.11 | ColumngsEL2AddressStatus | read-only | mandatory | This object indicates the status of the entry: other(1) - None of the following. learned(2) - This entry was learned dynamically. self(3) - The value of the co… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.2 | NodegsEL2AddrSummaryMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.4.2.1 | TablegsEL2AddrSummaryTable | not-accessible | mandatory | This summary table packs the address entries in the address database into summary objects. The goal is to optimize the upload of the large amount of data store… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.2.1.1 | RowgsEL2AddrSummaryEntry | not-accessible | mandatory | A summary object that packs as many address entries possible into a summary object. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.2.1.1.1 | ColumngsEL2AddrSummary | read-only | mandatory | The value of this object is a packed opaque structure representing an array of address entries. The format of this structure is: struct L2AddressEntry { UNS32 … |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3 | NodegsEL2AddrControlMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1 | TablegsEL2AddressControlTable | not-accessible | mandatory | This table provides the network manager the ability to create new, static address entries. Entries added through this table are added to the specified address … |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1 | RowgsEL2AddressControlEntry | not-accessible | mandatory | A control entry enables this manager to add a new entry to the specified address table. When the entry is written to, the control index value is reset to 0. Wh… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.1 | ColumngsEL2AddressControlIndex | read-only | mandatory | The index of the address entry that was created for this address. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.2 | ColumngsEL2AddressControlMacAddress | read-write | mandatory | The IEEE 802 MAC Address associated with this database entry. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.3 | ColumngsEL2AddressControlPortBinding | read-write | mandatory | The port to bind this address to. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.4 | ColumngsEL2AddressControlVlanID | read-write | mandatory | The VLAN ID of the VLAN to bind this address to. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.5 | ColumngsEL2AddressControlPriority | read-write | mandatory | If set to high(2), frames destined to this address are classified with priority value 4. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.6 | ColumngsEL2AddressControlPersistence | read-write | mandatory | The persistence of the entry to be created: permanent(1) - Address is not aged out. Additionally, if the address is seen as a source on a different port for th… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.3.1.1.7 | ColumngsEL2AddressControlStatus | read-write | mandatory | The status of an entry to be created. When adding an entry all fields will be set, and then the control status is set to createRequest(1), indicating that the … |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4 | NodegsEL2AddrChangeMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.1 | ScalargsEL2AddressChangeLast | read-only | mandatory | The index of the last entry written to the address change table |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.2 | ScalargsEL2AddressChangeWraps | read-only | mandatory | The count of the number of times the address change table has wrapped. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.3 | ScalargsEL2AddressChangeMaxEntries | read-write | mandatory | The maximum number of entries in the address change table. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.4 | TablegsEL2AddressChangeTable | not-accessible | mandatory | . |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.4.1 | RowgsEL2AddressChangeEntry | not-accessible | mandatory | The address change table provides a quick way of getting only the entries that have recently changed. Since entries age out as part of the normal switching pro… |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.4.1.1 | ColumngsEL2AddressChangeWrapCount | read-only | mandatory | The number of times that the gsEAddressChangeLastIndex had wrapped when this entry was added. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.4.1.2 | ColumngsEL2AddressChangeIndex | read-only | mandatory | The index that uniquely identifies this address change entry. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.4.1.3 | ColumngsEL2AddressChangeIndexChanged | read-only | mandatory | The address entry that changed. The value of this object corresponds to the gsEL2AddressIndex object. |
| 1.3.6.1.4.1.36.2.18.39.5.1.4.4.4.1.4 | ColumngsEL2AddressChangeSummary | read-only | mandatory | The structure is interpreted in the following manner: |
| 1.3.6.1.4.1.36.2.18.39.5.2 | NodegsESwitchPortMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.2.1 | TablegsESwitchPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1 | RowgsESwitchPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.1 | ColumngsESwitchPortIndex | read-only | mandatory | A unique index that identifies this switch port. The value of this index corresponds to the value of the gsEResourceIndex for switch ports. |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.2 | ColumngsESwitchPortSTAPMode | read-write | mandatory | Disabling spanning tree on a switch port prevents the switch port from participating in the spanning tree process. When disabled(2), this port will neither gen… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.3 | ColumngsESwitchPortConvertToStatic | read-write | mandatory | When this object is set to convertToStatic(2), all addresses learned on this port will be added to the non-volatile version of the static address table. Typica… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.4 | ColumngsESwitchPortLearningMode | read-write | mandatory | Disable learning on a bridge port to prevent new addresses from being added to the address database. Used in combination with static (permanent) address entrie… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.5 | ColumngsESwitchPortHuntGroup | read-write | mandatory | Hunt groups provide the capability to logically bind multiple switch ports into one switch port. This provides a way of balancing the load of multiple links be… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.6 | ColumngsESwitchPortPhysicalPort | read-only | mandatory | The physical port resource bound to this switch port. |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.7 | ColumngsESwitchPortKnownMode | read-write | mandatory | Enabling known mode for this switch port causes the port to safely discard frames flooded because they are unknown unicast frames. This mode greatly enhances t… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.8 | ColumngsESwitchPortMappingMethod | read-write | mandatory | The frame mapping method of this switch port. When set to port-based(1) (the factory default), all non-tagged frames are classified to the VLAN associated with… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.9 | ColumngsESwitchPortTrunkingMode | read-write | mandatory | The trunking mode of this port. All frames transmitted out this switch port are translated to the appropriate trunking format: Clear: Ethernet or IEEE 802.3 fr… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.10 | ColumngsESwitchPortVlanBindingMethod | read-write | mandatory | The VLAN binding method of a switch port specifies the way in which the port can be a member of the egress lists of VLANs other than the port default VLAN spec… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.11 | ColumngsESwitchPortIgnoreTag | read-write | mandatory | Each switch port is capable of ignoring the VLAN Tag associated with a frame in a trunking format. When ignored, the tag is used as the default in the event th… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.12 | ColumngsESwitchPortVlanID | read-write | mandatory | When this switch port is configured in port-based VLAN mode, all non-tagged frames received on this port are bound to this VLAN. Otherwise, non-tagged frames a… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.14 | ColumngsESwitchPortAutoVlanCreation | read-write | mandatory | Enabling auto VLAN creation for this switch port causes the port to dynamically create a VLAN whenever an IEEE 802.1Q or Multi-level tagged frame is received o… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.15 | ColumngsESwitchPortMirrorMode | read-only | mandatory | When set to enable(1), this object indicates that the port is defined as a mirror port through the gsEPortMirroringTable. A mirror port duplicates frames recei… |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.16 | ColumngsESwitchPortIfIndex | read-only | mandatory | Each switch port is associated with an interface. This object provides a mechanism to map switch ports to bridge ports. |
| 1.3.6.1.4.1.36.2.18.39.5.2.1.1.17 | ColumngsESwitchPortFastStart | read-write | mandatory | When this object is set to enable(1), bridge ports on this switch port transitions right from blocking to forwarding, skipping the listening and learning state… |
| 1.3.6.1.4.1.36.2.18.39.5.4 | NodegsEHuntGroupMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.4.1 | TablegsEHuntGroupTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1 | RowgsEHuntGroupEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1.1 | ColumngsEHuntGroupIndex | read-only | mandatory | An index that uniquely identifies this hunt group. This index corresponds to the value of gsEResourceIndex for resources of the hunt group type. |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1.2 | ColumngsEHuntGroupName | read-write | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1.3 | ColumngsEHuntGroupBasePort | read-only | mandatory | The switch port index that serves as the base port for this hunt group. Each hunt group requires a base port. In lieu of a specific configuration, the hunt gro… |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1.4 | ColumngsEHuntGroupNumberOfPorts | read-only | mandatory | The current number of ports that belong to this hunt group. |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1.5 | ColumngsEHuntGroupLoadSharing | read-write | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.4.1.1.6 | ColumngsEHuntGroupStatus | read-write | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.5.5 | NodegsEPortMirroringMgt | |||
| 1.3.6.1.4.1.36.2.18.39.5.5.1 | TablegsEPortMirroringTable | not-accessible | mandatory | A table of port mirroring entries used to mirror traffic from a source port to a mirror port. |
| 1.3.6.1.4.1.36.2.18.39.5.5.1.1 | RowgsEPortMirroringEntry | not-accessible | mandatory | Objects related to the PortMirroring functionality. |
| 1.3.6.1.4.1.36.2.18.39.5.5.1.1.1 | ColumngsEPortMirroringIndex | read-only | mandatory | The unique index that identifies this entry. This index consists of a switch fabric port and the index of a Packet Lookup Engine servicing this fabric port. |
| 1.3.6.1.4.1.36.2.18.39.5.5.1.1.2 | ColumngsEPortMirroringSourceSubPort | read-write | mandatory | The frame sampler source switch subport. The source port is the port from which received traffic will be mirrored. This object identifies the switch subport on… |
| 1.3.6.1.4.1.36.2.18.39.5.5.1.1.3 | ColumngsEPortMirroringSamplerType | read-write | mandatory | The type for this frame sampler. When set to enable(1), every frame received on the source port(s) will be mirrored at the mirror port. When set to disable(2),… |
| 1.3.6.1.4.1.36.2.18.39.5.5.1.1.4 | ColumngsEPortMirroringRate | read-write | mandatory | Used in conjunction with gsEPortMirroringSamplerType to implement periodic sampling functionality. If gsEPortMirroringSamplerType is set to periodic(3), this o… |
| 1.3.6.1.4.1.36.2.18.39.5.5.1.1.5 | ColumngsEPortMirroringMirrorPort | read-write | mandatory | The Switch Port on which frames received at source ports(s) will be duplicated. If no mirror port has been defined this object will return NULL. |
| 1.3.6.1.4.1.36.2.18.39.7 | NodegsEVlanMgt | |||
| 1.3.6.1.4.1.36.2.18.39.7.1 | NodegsEVlans | |||
| 1.3.6.1.4.1.36.2.18.39.7.1.1 | TablegsEVlanTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1 | RowgsEVlanEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.1 | ColumngsEVlanID | read-only | mandatory | An identifier that is unique within the administrative domain. This ID is assigned by the management application and is meaningful within that context. This ID… |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.2 | ColumngsEVlanName | read-write | mandatory | A user-assignable name for this Vlan. |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.3 | ColumngsEVlanIfIndex | read-only | mandatory | Each virtual LAN has a virtual interface associated with it. This enables RMON monitoring to occur per-VLAN. It also provides a handy mechanism to map virtual … |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.4 | ColumngsEVlanAFTIndex | read-write | mandatory | The address table used for this VLAN for explicitly tagged frames (frames received in a trunking frame format or from a port in port-based VLAN mode.) Normally… |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.5 | ColumngsEVlanBridgeIndex | read-write | mandatory | The bridge resource which is bound to this Vlan. |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.6 | ColumngsEVlanStatus | read-write | mandatory | The status of an entry to be created or deleted. When adding an entry all fields will be set, and then the status is set to createRequest(1) (indicating that t… |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.7 | ColumngsEVlanInitialHashTableSize | read-write | mandatory | The initial hash table size used for MAC addresses on this VLAN. This attribute may only be set when gsEVlanStatus is set to createRequest(1). It must be a pow… |
| 1.3.6.1.4.1.36.2.18.39.7.1.1.1.8 | ColumngsEVlanAutoIncrementHTSize | read-write | mandatory | This attribute specifies whether or not the hash table size used for MAC addresses on this VLAN is automatically increased as necessary to hold more MAC addres… |
| 1.3.6.1.4.1.36.2.18.39.7.4 | NodegsEVirtualPorts | |||
| 1.3.6.1.4.1.36.2.18.39.7.4.1 | TablegsEVirtualSwitchPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.7.4.1.1 | RowgsEVirtualSwitchPortEntry | not-accessible | mandatory | An instance of a virtual switch port indicates that this switch port is a member of this VLAN. |
| 1.3.6.1.4.1.36.2.18.39.7.4.1.1.1 | ColumngsEVirtualSwitchPortIndex | read-only | mandatory | The Resource ID of the virtual switch port bound to the VLAN. |
| 1.3.6.1.4.1.36.2.18.39.7.4.1.1.2 | ColumngsEVirtualSwitchPortFormat | read-write | mandatory | Typically, a VLAN capable switch port has one of three modes: access, trunk, or hybrid. In access mode, the port sends frames in clear format (untagged). In tr… |
| 1.3.6.1.4.1.36.2.18.39.7.4.1.1.3 | ColumngsEVirtualSwitchPortBridgePort | read-write | mandatory | The bridge port resource bound to this virtual port. |
| 1.3.6.1.4.1.36.2.18.39.7.4.1.1.4 | ColumngsEVirtualSwitchPortBindingType | read-only | mandatory | The method by which this switch port was bound to the VLAN. If the value is static(1), the binding was manually created by the administrator. If the value is p… |
| 1.3.6.1.4.1.36.2.18.39.7.4.1.1.5 | ColumngsEVirtualSwitchPortStatus | read-write | mandatory | The status of an entry to be created or deleted. When adding an entry all fields will be set, and then the status is set to createRequest(1) (indicating that t… |
| 1.3.6.1.4.1.36.2.18.39.10 | NodegsEEvents | |||
| 1.3.6.1.4.1.36.2.18.39.10.1 | NodegsEEventMgt | |||
| 1.3.6.1.4.1.36.2.18.39.10.1.1 | TablegsEEventTable | not-accessible | mandatory | Table of events currently supported. |
| 1.3.6.1.4.1.36.2.18.39.10.1.1.1 | RowgsEEventEntry | not-accessible | mandatory | Attributes associated with the event. |
| 1.3.6.1.4.1.36.2.18.39.10.1.1.1.1 | ColumngsEEventIndex | read-only | mandatory | |
| 1.3.6.1.4.1.36.2.18.39.10.1.1.1.2 | ColumngsEEventMode | read-write | mandatory | Disabling an event prevents this event from taking any actions when triggered. When set to enable to the console, the event will print the event information to… |
| 1.3.6.1.4.1.36.2.18.39.10.1.1.1.3 | ColumngsEEventLogAction | read-write | mandatory | When enabled, this action will cause an event log entry to be created. |
| 1.3.6.1.4.1.36.2.18.39.10.1.1.1.4 | ColumngsEEventTrapAction | read-write | mandatory | When enabled, this event will cause an SNMP trap to be generated. |
| 1.3.6.1.4.1.36.2.18.39.10.1.1.1.5 | ColumngsEEventConsoleAction | read-write | mandatory | When enabled, this event will cause a message to printed to the console serial port. |
| 1.3.6.1.4.1.36.2.18.39.10.2 | NodegsEEventLogMgt | |||
| 1.3.6.1.4.1.36.2.18.39.10.2.1 | ScalargsELogTableMaxSize | read-write | mandatory | The maximum number of entries in the log table. Changing this value causes the existing log to be truncated and rebuilt. |
| 1.3.6.1.4.1.36.2.18.39.10.2.2 | ScalargsELogLastEntry | read-only | mandatory | The log index of the last entry entered in the log. |
| 1.3.6.1.4.1.36.2.18.39.10.2.3 | ScalargsELogWraps | read-only | mandatory | The number of times that the last entry has wrapped from 65K back to 1. |
| 1.3.6.1.4.1.36.2.18.39.10.3 | NodegsEEventLog | |||
| 1.3.6.1.4.1.36.2.18.39.10.3.1 | TablegsEEventLogTable | not-accessible | mandatory | The log table for the events in the event table that are enabled for the Log Action. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1 | RowgsEEventLogEntry | not-accessible | mandatory | An entry in the log indicates information associated with a particular event. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.1 | ColumngsEEventLogEventIndex | read-only | mandatory | The index that uniquely identifies the event that caused this log entry. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.2 | ColumngsEEventLogIndex | read-only | mandatory | An index that uniquely identifies this log entry. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.3 | ColumngsEEventLogTime | read-only | mandatory | The value of sysUpTime when this event was triggered. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.4 | ColumngsEEventLogDescr | read-only | mandatory | The event log description. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.5 | ColumngsEEventLogType | read-only | mandatory | The type of event that caused this log entry. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.6 | ColumngsEEventLogSeverity | read-only | mandatory | The severity associated with this event. It is recommended that the severity be interpreted in the following manner: 0-19: Normal 20-39: Informational 40-59: W… |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.7 | ColumngsEEventLogDTM | read-only | mandatory | The date and time when this log entry was made. The format is yy-Mon- dd hh:mm:ss, time is in 24 hour time. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.8 | ColumngsEEventLogResType | read-only | mandatory | The type of object (if provided) that triggered this event. If not provided, the value is equal to 'Invalid Resource'. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.9 | ColumngsEEventLogResID | read-only | mandatory | The instance of this resource (if provided - see gsEEventLogResType) that triggered this event. |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.10 | ColumngsEEventLogResLeaf | read-only | mandatory | A number corresponding to the attribute associated with this resource and this event entry. It corresponds exactly to the leaf MIB number of the MIB that manag… |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.11 | ColumngsEEventLogValueType | read-only | mandatory | The data type associated with the log event value. This object indicates how to interpret the data stored in the event log value: - none(1) indicates no value … |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.12 | ColumngsEEventLogValue | read-only | mandatory | The value associated with the event encoded in an octet string. Refer to gsEEventLogValueType for how to interpret this value. The value encoded in this string… |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.13 | ColumngsEEventLogEpochTime | read-only | mandatory | The number of time ticks since the epoch when this event was logged. The interpretation of this value is as follows: struct DateTimeOvly { UNS32 year:6; UNS32 … |
| 1.3.6.1.4.1.36.2.18.39.10.3.1.1.14 | ColumngsEEventLogID | read-only | mandatory | A unique index that identifies the occurence of this event. This ID can be correlated between traps, logs and the like. |
| 1.3.6.1.4.1.36.2.18.39.10.4 | NodegsEShutdownLogMgt | |||
| 1.3.6.1.4.1.36.2.18.39.10.4.1 | ScalargsEShutdownLogTableMaxSize | read-write | mandatory | The maximum number of entries in the non-volatile log table. Changing the value of this object changes the maximum number of entries to be stored in Shutdown. |
| 1.3.6.1.4.1.36.2.18.39.10.4.2 | ScalargsEShutdownLogLastEntry | read-only | mandatory | The ID of the last entry made to the shutdown log. |
| 1.3.6.1.4.1.36.2.18.39.10.4.3 | ScalargsEShutdownLogAcknowledged | read-only | mandatory | This object is to set to acknowledged(2) the first time the Shutdown Log Table is accessed indicating that the Shutdown log has been read (at least once) since… |
| 1.3.6.1.4.1.36.2.18.39.10.5 | NodegsEEventShutdownLog | |||
| 1.3.6.1.4.1.36.2.18.39.10.5.1 | TablegsEEventShutdownLogTable | not-accessible | mandatory | A table of the last events logged before the system restarted. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1 | RowgsEEventShutdownLogEntry | not-accessible | mandatory | A log entry stored in non-volatile memory. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.1 | ColumngsEEventShutdownLogEventIndex | read-only | mandatory | The index that uniquely identifies the event that caused this ShutdownLog entry. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.2 | ColumngsEEventShutdownLogIndex | read-only | mandatory | An index that uniquely identifies this ShutdownLog entry. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.3 | ColumngsEEventShutdownLogTime | read-only | mandatory | The value of sysUpTime when this event was triggered. Note, the value corresponds to the sysUpTime when the system was last running (i.e. before it was shutdow… |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.4 | ColumngsEEventShutdownLogDescr | read-only | mandatory | The event ShutdownLog description. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.5 | ColumngsEEventShutdownLogType | read-only | mandatory | The type of event that caused this ShutdownLog entry. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.6 | ColumngsEEventShutdownLogSeverity | read-only | mandatory | The severity associated with this event. It is recommended that the severity be interpreted in the following manner: 0-19: Normal 20-39: Informational 40-59: W… |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.7 | ColumngsEEventShutdownLogDTM | read-only | mandatory | The date and time when this ShutdownLog entry was made. The format is yy-Mon-dd hh:mm:ss, time is in 24 hour time. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.8 | ColumngsEEventShutdownLogResType | read-only | mandatory | The type of object (if provided) that triggered this event. If not provided, the value is invalid. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.9 | ColumngsEEventShutdownLogResID | read-only | mandatory | The instance of this resource (if provided) that triggered this event. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.10 | ColumngsEEventShutdownLogResLeaf | read-only | mandatory | To be provided. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.11 | ColumngsEEventShutdownLogValueType | read-only | mandatory | The data type associated with the ShutdownLog event value. This object indicates how to interpret the data stored in the event ShutdownLog value. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.12 | ColumngsEEventShutdownLogValue | read-only | mandatory | The value associated with the event encoded in an octet string. |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.13 | ColumngsEEventShutdownLogEpochTime | read-only | mandatory | The number of time ticks since the epoch when this event was logged. The interpretation of this value is as follows: struct DateTimeOvly { UNS32 year:6; UNS32 … |
| 1.3.6.1.4.1.36.2.18.39.10.5.1.1.14 | ColumngsEEventShutdownLogID | read-only | mandatory | A unique index that identifies the occurence of this event. This ID can be correlated between traps, logs and the like. |
| 1.3.6.1.4.1.36.2.18.39.10.6 | NodegsEEventTrapMgmt | |||
| 1.3.6.1.4.1.36.2.18.39.10.6.1 | ScalargsEEventTrapEventIndex | read-only | mandatory | The index that uniquely identifies the event that caused this trap. |
| 1.3.6.1.4.1.36.2.18.39.10.6.2 | ScalargsEEventTrapTime | read-only | mandatory | The value of sysUpTime when this event was triggered. |
| 1.3.6.1.4.1.36.2.18.39.10.6.3 | ScalargsEEventTrapDescr | read-only | mandatory | The event log description. |
| 1.3.6.1.4.1.36.2.18.39.10.6.4 | ScalargsEEventTrapType | read-only | mandatory | The type of event that caused this trap. |
| 1.3.6.1.4.1.36.2.18.39.10.6.5 | ScalargsEEventTrapSeverity | read-only | mandatory | The severity associated with this event. It is recommended that the severity be interpreted in the following manner: 0-19: Normal 20-39: Informational 40-59: W… |
| 1.3.6.1.4.1.36.2.18.39.10.6.6 | ScalargsEEventTrapDTM | read-only | mandatory | The date and time when this trap was sent. The format is yy-Mon- dd hh:mm:ss, time is in 24 hour time. |
| 1.3.6.1.4.1.36.2.18.39.10.6.7 | ScalargsEEventTrapResType | read-only | mandatory | The type of object (if provided) that triggered this event. If not provided, the value is equal to 'Invalid Resource'. |
| 1.3.6.1.4.1.36.2.18.39.10.6.8 | ScalargsEEventTrapResID | read-only | mandatory | The instance of this resource (if provided - see gsEEventTrapResType) that triggered this event. |
| 1.3.6.1.4.1.36.2.18.39.10.6.9 | ScalargsEEventTrapResLeaf | read-only | mandatory | A number corresponding to the attribute associated with this resource and this event entry. It corresponds exactly to the leaf MIB number of the MIB that manag… |
| 1.3.6.1.4.1.36.2.18.39.10.6.10 | ScalargsEEventTrapValueType | read-only | mandatory | The data type associated with the trap event value. This object indicates how to interpret the data stored in the event trap value: - none(1) indicates no valu… |
| 1.3.6.1.4.1.36.2.18.39.10.6.11 | ScalargsEEventTrapValue | read-only | mandatory | The value associated with the event encoded in an octet string. Refer to gsEEventTrapValueType for how to interpret this value. The value encoded in this strin… |
| 1.3.6.1.4.1.36.2.18.39.10.6.12 | ScalargsEEventTrapEpochTime | read-only | mandatory | The number of time ticks since the epoch when this event was logged. The interpretation of this value is as follows: struct DateTimeOvly { UNS32 year:6; UNS32 … |
| 1.3.6.1.4.1.36.2.18.39.10.6.13 | ScalargsEEventTrapID | read-only | mandatory | A unique index that identifies the occurence of this event. This ID can be correlated between traps, logs and the like. |
| 1.3.6.1.4.1.36.2.18.39.11 | NodegsEAlarmMgt | |||
| 1.3.6.1.4.1.36.2.18.39.11.1 | NodegsEAlarmGeneral | |||
| 1.3.6.1.4.1.36.2.18.39.11.1.1 | ScalargsEAlarmGeneralActiveEntries | read-only | mandatory | The total number of alarm entries in the triggered state currently in the alarm table. |
| 1.3.6.1.4.1.36.2.18.39.11.1.2 | ScalargsEAlarmGeneralTimeStamp | read-only | mandatory | The value of sysUpTime when any alarm state last changed (either triggering a new alarm or re-arming an old one). |
| 1.3.6.1.4.1.36.2.18.39.11.2 | NodegsEAlarms | |||
| 1.3.6.1.4.1.36.2.18.39.11.2.2 | TablegsEActiveAlarmTable | not-accessible | mandatory | A table of all alarms in the triggered state. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1 | RowgsEActiveAlarmEntry | not-accessible | mandatory | An alarm in the triggered state. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.1 | ColumngsEActiveAlarmIndex | read-only | mandatory | The unique index that identifies this alarm. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.2 | ColumngsEActiveAlarmName | read-only | mandatory | The name of this alarm. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.3 | ColumngsEActiveAlarmValueHigh | read-only | mandatory | The high order 32 bits of the value that triggered this alarm. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.4 | ColumngsEActiveAlarmValueLow | read-only | mandatory | The low order 32 bits of the value that triggered this alarm. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.5 | ColumngsEActiveAlarmVariable | read-only | mandatory | The OID of the alarm variable if this is a user-created alarm (null otherwise). |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.6 | ColumngsEActiveAlarmResType | read-only | mandatory | The resource type of this alarm if this is an internally created alarm. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.7 | ColumngsEActiveAlarmResID | read-only | mandatory | The resource identifier associated with this alarm if this is an internally created alarm. |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.8 | ColumngsEActiveAlarmLeaf | read-only | mandatory | The leaf index of the MIB table used to manage this resource that is associated with this alarm, if this is an internally created alarm. For example, if this a… |
| 1.3.6.1.4.1.36.2.18.39.11.2.2.1.9 | ColumngsEActiveAlarmOwner | read-only | mandatory | This is the owner of the alarm. |
| 1.3.6.1.4.1.36.2.18.39.13 | NodegsESnmpTraps | |||
| 1.3.6.1.4.1.36.2.18.39.13.2 | NodegsESystemTrap | A gsESystemTrap is sent by the agent when a system event is triggered. These events are usually triggered when the software encounters an unexpected situation,… | ||
| 1.3.6.1.4.1.36.2.18.39.13.3 | NodegsEConfigurationTrap | A gsEConfigurationTrap is sent by the agent when the configuration event is triggered. These events are triggered when a configuration change is made. | ||
| 1.3.6.1.4.1.36.2.18.39.13.4 | NodegsETemperatureTrap | A gsETemperatureTrap is sent by the agent when the temperature event is triggered. This event is triggered when a temperature probe detects the temperature cro… | ||
| 1.3.6.1.4.1.36.2.18.39.13.5 | NodegsEResourceTrap | A gsEResourceTrap is sent by the agent when the resource event is triggered. The resource event is triggered when a resource is added or removed from the syste… | ||
| 1.3.6.1.4.1.36.2.18.39.13.6 | NodegsEFanTrap | A gsEFanTrap is sent by the agent when the fan status event is triggered. The fan status event is triggered when a fan has a change in its status. | ||
| 1.3.6.1.4.1.36.2.18.39.13.9 | NodegsEPowerTrap | A gsEPowerTrap is sent by the agent when the power event is triggered. These events are triggered when a power supply changes status. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BridgeId | OCTET STRING (SIZE (8)) | ||
| DisplayString | OCTET STRING | ||
| EventCategory | INTEGER { userDefined(1), coldstart(2), warmstart(3), linkUp(4), linkDown(5), newResource(6), deletedResource(7), tempStatus(8), configuration(9), scheduled(10), authentication(11), system(12), risingThreshold(13), fallingThreshold(14), fanStatus(15), powerStatus(16), status(17), bridgeNewRoot(18), bridgeTopChange(19), switchFabricStatus(20) } | ||
| EventValueType | INTEGER { none(1), integer(2), longInteger(3), string(4), octets(5), ipAddress(6), macAddress(7), timeTicks(8) } | ||
| MacAddress | OCTET STRING (SIZE (6)) | ||
| ResourceId | OBJECT IDENTIFIER | ||
| ResourceType | INTEGER { system(1), module(2), fan(3), temperatureSensor(4), interface(5), powerSupply(6), display(7), switchPort(8), bridge(9), vlan(10), aft(11), inboundGroupTable(12), outboundGroupTable(13), event(15), alarm(16) } | ||
| RowStatus | INTEGER { | ||
| Timeout | INTEGER |