GMPLS-TE-MIB
66 objects
This MIB module contains managed object definitions for GMPLS Traffic Engineering (TE).
Imported Objects
| GMPLS-TC-MIB MISSING | GmplsHopUnnumAddrTypes |
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddressIPv4 InetAddressIPv6 |
| MPLS-TC-MIB | MplsTunnelIndex MplsTunnelInstanceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 experimental Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.3 | IdentitygmplsTeMIB | This MIB module contains managed object definitions for GMPLS Traffic Engineering (TE). | ||
| 1.3.6.1.3.1 | NodegmplsTeScalars | |||
| 1.3.6.1.3.1.1 | ScalargmplsTunnelsConfigured | read-only | current | The number of GMPLS tunnels configured on this device. A tunnel is considered configured if an entry for the tunnel exists in the gmplsTunnelTable and the asso… |
| 1.3.6.1.3.1.2 | ScalargmplsTunnelActive | read-only | current | The number of GMPLS tunnels active on this device. A tunnel is considered active if there is an entry in the gmplsTunnelTable and the associated mplsTunnelOper… |
| 1.3.6.1.3.2 | NodegmplsTeObjects | |||
| 1.3.6.1.3.2.1 | TablegmplsTunnelTable | not-accessible | current | The gmplsTunnelTable 'extends' the mplsTunnelTable. It allows GMPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reco… |
| 1.3.6.1.3.2.1.1 | RowgmplsTunnelEntry | not-accessible | current | An entry in this table in association with the corresponding entry in the mplsTunnelTable represents a GMPLS tunnel. An entry can be created by a network admin… |
| 1.3.6.1.3.2.1.1.1 | ColumngmplsTunnelUnnumIf | read-create | current | Denotes whether or not this tunnel corresponds to an unnumbered interface represented in the interfaces group table. This object is only used if mplsTunnelIsIf… |
| 1.3.6.1.3.2.1.1.2 | ColumngmplsTunnelAttributes | read-create | current | This bitmask indicates optional parameters for this tunnel. Some of these bits map direct to signaled values (for example SESSION_ATTRIBUTES flags in RSVP-TE).… |
| 1.3.6.1.3.2.1.1.3 | ColumngmplsTunnelLSPEncoding | read-create | current | This object indicates the encoding of the LSP being requested. Ed Note: Should these be assigned and maintained by IANA? |
| 1.3.6.1.3.2.1.1.4 | ColumngmplsTunnelSwitchingType | read-create | current | Indicates the type of switching that should be performed on a particular link. This field is needed for links that advertise more than one type of switching ca… |
| 1.3.6.1.3.2.1.1.5 | ColumngmplsTunnelLinkProtection | read-create | current | This bitmask indicates the level of link protection required. A value of zero (no bits set) indicates that any protection may be used. This object is only used… |
| 1.3.6.1.3.2.1.1.6 | ColumngmplsTunnelGPid | read-create | current | This object indicates the payload carried by the LSP. It is only required when GMPLS will be used for this LSP. This object is only used if gmplsTunnelLSPEncod… |
| 1.3.6.1.3.2.1.1.7 | ColumngmplsTunnelSecondary | read-create | current | Indicates that the requested LSP is a secondary LSP. This object is only used if gmplsTunnelLSPEncoding is not set to 0. |
| 1.3.6.1.3.2.1.1.8 | ColumngmplsTunnelDirection | read-create | current | Whether this tunnel carries forward data (is unidirectional) or is bidirectional. By default, tunnels are unidirectional. |
| 1.3.6.1.3.2.1.1.9 | ColumngmplsTunnelPathComp | read-create | current | This value instructs the source node on how to perform path computation on the explicit route specified by the associated entries in the gmplsTunnelHopTable. d… |
| 1.3.6.1.3.2.2 | TablegmplsTunnelHopTable | not-accessible | current | The gmplsTunnelHopTable 'extends' the mplsTunnelHopTable. It is used to indicate the explicit labels and unnumbered interface hops to be used for a GMPLS tunne… |
| 1.3.6.1.3.2.2.1 | RowgmplsTunnelHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled an ERLSP to be set up by a signaling protocol. |
| 1.3.6.1.3.2.2.1.1 | ColumngmplsTunnelHopUnnumAddrType | read-create | current | Indicates whether this tunnel hop entry uses an unnumbered link and, if so, whether it is an Ipv4 or Ipv6 hop. When this object is set to unnumberedIfIpV4(2) o… |
| 1.3.6.1.3.2.2.1.2 | ColumngmplsTunnelHopLabelStatuses | read-only | current | This bitmask indicates the presence and status of labels indicated by the gmplsTunnelHopExplicitLabel and gmplsTunnelHopExplicitReverseLabel objects. For the P… |
| 1.3.6.1.3.2.2.1.3 | ColumngmplsTunnelHopExplicitLabel | read-create | current | Indicates the row entry in the mplsLabelTabel that defines the explicit label to use in the explicit route as the forward path label at this point. This value … |
| 1.3.6.1.3.2.2.1.4 | ColumngmplsTunnelHopExplicitReverseLabel | read-create | current | Indicates the row entry in the mplsLabelTabel that defines the explicit label to use in the explicit route as the reverse path label at this point. This value … |
| 1.3.6.1.3.2.2.1.5 | ColumngmplsTunnelHopUnnumberedInterface | read-create | current | Indicates the interface index of the unnumbered interface to use when setting up the LSP. Only has value when gmplsTunnelHopUnnumAddrType is set to unnumberedI… |
| 1.3.6.1.3.2.3 | TablegmplsTunnelARHopTable | not-accessible | current | The gmplsTunnelARHopTable 'extends' the mplsTunnelARHopTable. It is used to indicate the unnumbered hops, strict or loose, for a GMPLS tunnel defined in mplsTu… |
| 1.3.6.1.3.2.3.1 | RowgmplsTunnelARHopEntry | not-accessible | current | An entry in this table represents additional information about a GMPLS tunnel hop. An entry is created by the signaling protocol for a signaled ERLSP set up by… |
| 1.3.6.1.3.2.3.1.1 | ColumngmplsTunnelARHopUnnumAddrType | read-only | current | Denotes whether this tunnel hop uses numbered or unnumbered interfaces. If set to unnumberedIfIpV4(2) or unnumberedIfIpV6(3) the value overrides the value of t… |
| 1.3.6.1.3.2.3.1.2 | ColumngmplsTunnelARHopLabelStatuses | read-only | current | This bitmask indicates the presence and status of labels indicated by the gmplsTunnelARHopExplicitLabel and gmplsTunnelARHopExplicitReverseLabel objects. For t… |
| 1.3.6.1.3.2.3.1.3 | ColumngmplsTunnelARHopExplicitLabel | read-only | current | Indicates the row entry in the mplsLabelTabel that defines the label used in the path as forward path at this point. This value only has meaning if the forward… |
| 1.3.6.1.3.2.3.1.4 | ColumngmplsTunnelARHopExplicitReverseLabel | read-only | current | Indicates the row entry in the mplsLabelTabel that defines the label used in the path as reverse path at this point. This value only has meaning if the reverse… |
| 1.3.6.1.3.2.3.1.5 | ColumngmplsTunnelARHopUnnumberedInterface | read-only | current | Indicates the interface index of the unnumbered interface used when setting up the LSP. Only has value when gmplsTunnelARHopUnnumAddrType is set to unnumberedI… |
| 1.3.6.1.3.2.3.1.6 | ColumngmplsTunnelARHopProtection | read-only | current | Availability and usage of protection on the reported link. - localAvailable indicates that the link downstream of this node is protected via a local repair mec… |
| 1.3.6.1.3.2.4 | TablegmplsTunnelCHopTable | not-accessible | current | The gmplsTunnelCHopTable 'extends' the mplsTunnelCHopTable. It is used to indicate additional information about the hops of a GMPLS tunnel defined in mplsTunne… |
| 1.3.6.1.3.2.4.1 | RowgmplsTunnelCHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry in this table is created by a constraint-based routing protocol based on the hops specified in the cor… |
| 1.3.6.1.3.2.4.1.1 | ColumngmplsTunnelCHopUnnumAddrType | read-only | current | Denotes whether this tunnel hop uses numbered or unnumbered interfaces. If set to unnumberedIfIpV4(2) or unnumberedIfIpV6(3) the value overrides the value of t… |
| 1.3.6.1.3.2.4.1.2 | ColumngmplsTunnelCHopLabelStatuses | read-only | current | This bitmask indicates the presence and status of labels indicated by the gmplsTunnelCHopExplicitLabel and gmplsTunnelCHopExplicitReverseLabel objects. For the… |
| 1.3.6.1.3.2.4.1.3 | ColumngmplsTunnelCHopExplicitLabel | read-only | current | Indicates the row entry in the mplsLabelTabel that defines the explicit label to use in the explicit route as the forward path label at this point. This value … |
| 1.3.6.1.3.2.4.1.4 | ColumngmplsTunnelCHopExplicitReverseLabel | read-only | current | Indicates the row entry in the mplsLabelTabel that defines the explicit label to use in the explicit route as the reverse path label at this point. This value … |
| 1.3.6.1.3.2.4.1.5 | ColumngmplsTunnelCHopUnnumberedInterface | read-only | current | Indicates the interface index of the unnumbered interface to use when setting up the LSP. Only has value when gmplsTunnelCHopUnnumAddrType is set to unnumbered… |
| 1.3.6.1.3.2.5 | TablegmplsTunnelPacketPerfTable | not-accessible | current | This table provides per-tunnel packet performance information. |
| 1.3.6.1.3.2.5.1 | RowgmplsTunnelPacketPerfEntry | not-accessible | current | An entry in this table is created by the LSR for every GMPLS tunnel where packets are visible to the LSR. Its is an extension to gmplsTunnelEntry. |
| 1.3.6.1.3.2.5.1.1 | ColumngmplsTunnelPacketPerfRvsPackets | read-only | current | Number of packets forwarded on the tunnel in the reverse direction if it is bidirectional. |
| 1.3.6.1.3.2.5.1.2 | ColumngmplsTunnelPacketPerfRvsHCPackets | read-only | current | High capacity counter for number of packets forwarded on the tunnel in the reverse direction if it is bidirectional. |
| 1.3.6.1.3.2.5.1.3 | ColumngmplsTunnelPacketPerfRvsErrors | read-only | current | Number of errored packets received on the tunnel in the reverse direction if it is bidirectional. |
| 1.3.6.1.3.2.5.1.4 | ColumngmplsTunnelPacketPerfRvsBytes | read-only | current | Number of bytes forwarded on the tunnel in the reverse direction if it is bidirectional. |
| 1.3.6.1.3.2.5.1.5 | ColumngmplsTunnelPacketPerfRvsHCBytes | read-only | current | High capacity counter for number of bytes forwarded on the tunnel in the reverse direction if it is bidirectional. |
| 1.3.6.1.3.2.6 | TablegmplsTunnelErrorTable | not-accessible | current | This table provides per-tunnel information about errors. Errors may be detected locally or reported through the signaling protocol. |
| 1.3.6.1.3.2.6.1 | RowgmplsTunnelErrorEntry | not-accessible | current | An entry in this table is created by the LSR for every tunnel where error information is visible to the LSR. Its is an extension to gmplsTunnelEntry. |
| 1.3.6.1.3.2.6.1.1 | ColumngmplsTunnelErrorLastError | read-only | current | The nature of the last error. Protocol errors encompass all errors that may be reported through the protocol and give a wider set of error codes than those pro… |
| 1.3.6.1.3.2.6.1.2 | ColumngmplsTunnelErrorLastTime | read-only | current | The time at which the last error occurred. This is presented as the value of SysUpTime when the error occurred or was reported to this node. If gmplsTunnelErro… |
| 1.3.6.1.3.2.6.1.3 | ColumngmplsTunnelErrorReporterType | read-only | current | The reporter of the last error recorded. This object is used principally to aid in interpretation of gmplsTunnelErrorReporterIpv4Addr and gmplsTunnelErrorRepor… |
| 1.3.6.1.3.2.6.1.4 | ColumngmplsTunnelErrorReporterIpv4Addr | read-only | current | The address of the node reporting the last error, or the address of the resource (such as an interface) associated with the error. This object only has meaning… |
| 1.3.6.1.3.2.6.1.5 | ColumngmplsTunnelErrorReporterIpv6Addr | read-only | current | The address of the node reporting the last error, or the address of the resource (such as an interface) associated with the error. This object only has meaning… |
| 1.3.6.1.3.2.6.1.6 | ColumngmplsTunnelErrorProtocolCode | read-only | current | The primary error code associated with the last error and the protocol used to signal this tunnel. The relevant protocol is indicated by the gmplsTunnelSignall… |
| 1.3.6.1.3.2.6.1.7 | ColumngmplsTunnelErrorProtocolSubcode | read-only | current | The secondary error code associated with the last error and the protocol used to signal this tunnel. The relevant protocol is indicated by the gmplsTunnelSigna… |
| 1.3.6.1.3.2.6.1.8 | ColumngmplsTunnelErrorHelpString | read-only | current | A textual string containing information about the last error, recovery actions and support advice. If there is no help string this object contains a zero lengt… |
| 1.3.6.1.3.3 | NodegmplsTeConformance | |||
| 1.3.6.1.3.3.1 | NodegmplsTeGroups | |||
| 1.3.6.1.3.3.1.1 | GroupgmplsTunnelGroup | current | Necessary, but not sufficient, set of objects to implement tunnels. In addition, depending on the type of the tunnels supported (for example, manually configur… | |
| 1.3.6.1.3.3.1.2 | GroupgmplsTunnelManualGroup | current | Object(s) needed to implement manually configured tunnels. | |
| 1.3.6.1.3.3.1.3 | GroupgmplsTunnelSignaledGroup | current | Objects needed to implement signaled tunnels. | |
| 1.3.6.1.3.3.1.4 | GroupgmplsTunnelScalarGroup | current | Scalar objects needed to implement MPLS tunnels. | |
| 1.3.6.1.3.3.1.5 | GroupgmplsTunnelIsIntfcGroup | current | Objects needed to implement tunnels that are interfaces. | |
| 1.3.6.1.3.3.1.6 | GroupgmplsTunnelIsNotIntfcGroup | current | Objects needed to implement tunnels that are not interfaces. | |
| 1.3.6.1.3.3.1.7 | GroupgmplsTunnelOptionalGroup | current | The objects in this group are optional. | |
| 1.3.6.1.3.3.2 | NodegmplsTeCompliances | |||
| 1.3.6.1.3.3.2.1 | CompliancegmplsTeModuleCompliance | read-only | current | Compliance statement for agents that support the GMPLS TE MIB. |