HITRON-CABLE-MODEM-MIB
224 objects
This is the MIB module for Hitron DOCSIS compliant Cable Modem.
Imported Objects
| HITRON-MIB | hitronMib |
| INET-ADDRESS-MIB | InetAddress |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter64 enterprises Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString PhysAddress RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.8595.2 | IdentityhitronDOCSIS | This is the MIB module for Hitron DOCSIS compliant Cable Modem. | ||
| 1.3.6.1.4.1.8595.2.1 | NodehitronCm | |||
| 1.3.6.1.4.1.8595.2.1.1 | NodehitronCmScanningParameters | |||
| 1.3.6.1.4.1.8595.2.1.1.1 | ScalarhitronScanFreqStart | read-write | current | This object is the Lowest downstream channel center frequency in the scan range before wraping back to HighDownstreamChannelFreq. For US, this value must be be… |
| 1.3.6.1.4.1.8595.2.1.1.2 | ScalarhitronScanFreqStop | read-write | current | This object is the Highest downstream channel center frequency in the scan range before wraping back to LowDownstreamChannelFreq. For US, this value must be be… |
| 1.3.6.1.4.1.8595.2.1.1.3 | ScalarhitronFrequencyPlanInUse | read-write | current | If provied, only scan this frequency plan, if USA, scan IRC first and then scan HRC. The AUTO is for Euro-Board only. if provided, will try both of Docsis and … |
| 1.3.6.1.4.1.8595.2.1.1.4 | ScalarhitronDirectionToScan | read-write | current | The object is the direction of the scanning. |
| 1.3.6.1.4.1.8595.2.1.1.5 | ScalarhitronEuropeanScanStep | read-write | current | It is only apply for Europe-like frequency scanning, including euro and auto plan . The scanning step represents how many steps will be skiped for the next cha… |
| 1.3.6.1.4.1.8595.2.1.1.6 | TablehitronGoldFreqProvTable | not-accessible | current | This table defines the set of downstream channel frequencies to scan before any other channel frequencies. The lowest index entries are searched first, skippin… |
| 1.3.6.1.4.1.8595.2.1.1.6.1 | RowhitronGoldFreqProvEntry | not-accessible | current | Each entry defines a downstream channel frequency to scan first during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.6.1.1 | ColumnhitronGoldProvIndex | not-accessible | current | The index of the Provisioned Gold List entry |
| 1.3.6.1.4.1.8595.2.1.1.6.1.2 | ColumnhitronGoldProvStatus | read-create | current | Controls and reflects the status of rows in this table. Rows in this table may be created by either the create-and-go or create-and-wait paradigms. There is no… |
| 1.3.6.1.4.1.8595.2.1.1.6.1.3 | ColumnhitronGoldProvFrequency | read-write | current | The Golden Frequency used during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.7 | TablehitronGoldFreqLearnedTable | not-accessible | current | Learned Golden Frequencies. A frequency will be entered into this table once the modem has succesfully registered on it. |
| 1.3.6.1.4.1.8595.2.1.1.7.1 | RowhitronGoldFreqLearnedEntry | not-accessible | current | Each entry defines a downstream channel freuency to scan first during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.7.1.1 | ColumnhitronGoldLearnedIndex | not-accessible | current | The index of the Learned Gold List entry |
| 1.3.6.1.4.1.8595.2.1.1.7.1.2 | ColumnhitronGoldLearnedFrequency | read-write | current | The Learned Gold frequency learned. It is not possible to modify the value of this frequency to any other value than '0'. Setting a value to '0' will delete th… |
| 1.3.6.1.4.1.8595.2.1.1.8 | TablehitronBlackFreqProvTable | not-accessible | current | This table defines the set of downstream channel frequencies to be skipped from scanning. The skipping should happen during the whole channel plan scanning. Al… |
| 1.3.6.1.4.1.8595.2.1.1.8.1 | RowhitronBlackFreqProvEntry | not-accessible | current | Each entry defines a downstream channel frequency to be skipped during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.8.1.1 | ColumnhitronBlackProvIndex | not-accessible | current | The index of the Provisioned Black List entry |
| 1.3.6.1.4.1.8595.2.1.1.8.1.2 | ColumnhitronBlackProvStatus | read-create | current | Controls and reflects the status of rows in this table. Rows in this table may be created by either the create-and-go or create-and-wait paradigms. There is no… |
| 1.3.6.1.4.1.8595.2.1.1.8.1.3 | ColumnhitronBlackProvFrequency | read-write | current | The Black Frequency to be skipped during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.9 | TablehitronBlackFreqLearnedTable | not-accessible | current | Learned Black Frequencies. A frequency will be entered into this table once the modem has succesfully locked it, but unable to get the DOCSIS messages or unabl… |
| 1.3.6.1.4.1.8595.2.1.1.9.1 | RowhitronBlackFreqLearnedEntry | not-accessible | current | Each entry defines a downstream channel freuency to be skipped during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.9.1.1 | ColumnhitronBlackLearnedIndex | not-accessible | current | The index of the Learned Black List entry |
| 1.3.6.1.4.1.8595.2.1.1.9.1.2 | ColumnhitronBlackLearnedFrequency | read-write | current | The Learned Black frequency learned. It is not possible to modify the value of this frequency to any other value than '0'. Setting a value to '0' will delete t… |
| 1.3.6.1.4.1.8595.2.1.1.10 | ScalarhitronSelectISP | read-write | current | This OID allows for several ISP on the same cable network as it sets a ISP identifier in CM non-volatile memory. The configuration file needs to contain a vend… |
| 1.3.6.1.4.1.8595.2.1.1.11 | TablehitronMSOFreqTable | not-accessible | current | This table defines the set of downstream channel frequencies to scan before any other channel frequencies. The lowest index entries are searched first, skippin… |
| 1.3.6.1.4.1.8595.2.1.1.11.1 | RowhitronMSOFreqEntry | not-accessible | current | Each entry defines a downstream channel frequency to scan first during scanning. |
| 1.3.6.1.4.1.8595.2.1.1.11.1.1 | ColumnhitronMSOFreqIndex | not-accessible | current | The index of the MSO Frequency List entry |
| 1.3.6.1.4.1.8595.2.1.1.11.1.2 | ColumnhitronMSOFreqFrequency | read-write | current | The MSO Frequency used during scanning. |
| 1.3.6.1.4.1.8595.2.1.2 | NodehitronCmManagementParameters | |||
| 1.3.6.1.4.1.8595.2.1.2.1 | ScalarhitronCmDhcpServerEnable | read-write | obsolete | This object is used to enable/disable DHCP Local Server. As long as CM is not operational, local DHCP Server is working if enabled. Set to true(1) to enable DH… |
| 1.3.6.1.4.1.8595.2.1.2.2 | TablehitronCmDaemonAccessTable | not-accessible | current | This table allows control of accessing the CM daemons, like TELNET, HTTP, SNMP, HTTPS and SSH. |
| 1.3.6.1.4.1.8595.2.1.2.2.1 | RowhitronCmDaemonAccessEntry | not-accessible | current | Allow configuration for accessing control of different cable modem daemons from different interfaces. |
| 1.3.6.1.4.1.8595.2.1.2.2.1.1 | ColumnhitronCmDaemonCapability | not-accessible | current | The daemon list that is controlled by this entry. SNMP is only supported on 3.0 products. |
| 1.3.6.1.4.1.8595.2.1.2.2.1.2 | ColumnhitronCmDaemonAccessible | read-write | current | When flag(s) is enabled ((cpe/rfi)AccessEnabled = 1) indicates that access through specific interface(s) is enable. If disabled(=0), indicates that any daemon … |
| 1.3.6.1.4.1.8595.2.1.2.3 | ScalarhitronResetFactory | read-write | current | Reset the unit to factory default. this will also wipe any learned golden frequencies and reset the unit to the state as from factory. WARNING: the behaviour o… |
| 1.3.6.1.4.1.8595.2.1.2.4 | ScalarhitronCmIGMPMaxStreams | read-write | current | This object allows the setting of the maximum number of multicast streams the unit will bridge at the same time. This is done by snooping the IGMP-Join message… |
| 1.3.6.1.4.1.8595.2.1.2.5 | ScalarhitronCmIGMPTimeout | read-write | current | This OID determines the Maximum delay for passive mode IGMP Membership reports in 1/10th of seconds. This timer has a default value of 3 seconds therefore a va… |
| 1.3.6.1.4.1.8595.2.1.2.6 | ScalarhitronLedControl | read-write | current | This OID allows to control the LED on the device, with exception of the power led. When active, the led have the normal behaviour. When inactive only the power… |
| 1.3.6.1.4.1.8595.2.1.2.7 | ScalarhitronHttpPasswordControl | read-write | current | This OID allows to enable/disable of the password control of http access on the device,for httpPassword, disabled means that access to the webpages doesn't nee… |
| 1.3.6.1.4.1.8595.2.1.2.8 | ScalarhitronTurboDoxControl | read-write | current | Config PP and Turbodox control. auto(0): 10/100M link speed CPE, PP on Tdox off; 1G link speed CPE, PP and Tdox off. enabled(1): PP and Tdox On. tdoxdisabled(2… |
| 1.3.6.1.4.1.8595.2.1.2.9 | ScalarhitronMaxCpesControl | read-write | current | Config MAX CPES settings. |
| 1.3.6.1.4.1.8595.2.1.2.10 | TablehitronCmUserPasswordTable | not-accessible | current | This table allows configuration of change user password |
| 1.3.6.1.4.1.8595.2.1.2.10.1 | RowhitronCmUserPasswordEntry | not-accessible | current | Allow configuration for change user password by role. |
| 1.3.6.1.4.1.8595.2.1.2.10.1.1 | ColumnhitronCmUserRole | not-accessible | current | Select User Role |
| 1.3.6.1.4.1.8595.2.1.2.10.1.2 | ColumnhitronCmPassword | read-write | current | Set password for the selected user in hitronCmUserRole. For CM/eMTA products, only admin user is supported. So, for other user role, the password setting would… |
| 1.3.6.1.4.1.8595.2.1.2.10.1.3 | ColumnhitronCmUsername | read-write | current | Set username for the selected user in hitronCmUserRole. For CM/eMTA products, only admin user is supported. So, for other user role, the username setting would… |
| 1.3.6.1.4.1.8595.2.1.2.11 | TablehitronDQoSControlTable | not-accessible | current | This table contains the information for the DQoS control entries. |
| 1.3.6.1.4.1.8595.2.1.2.11.1 | RowhitronDQoSControlEntry | not-accessible | current | The table that describes the DQoS Control PROFILE. |
| 1.3.6.1.4.1.8595.2.1.2.11.1.1 | ColumnhitronDQoSControlOrder | not-accessible | current | Integer index into the hitron DQoS for SIP server table |
| 1.3.6.1.4.1.8595.2.1.2.11.1.2 | ColumnhitronDQoSSIPServerIP | read-create | current | The allowed SIP server which could trigger the DQoS |
| 1.3.6.1.4.1.8595.2.1.2.11.1.3 | ColumnhitronDQoSSIPServerPort | read-create | current | The SIP server port which allow the triggering of the DQoS |
| 1.3.6.1.4.1.8595.2.1.2.11.1.4 | ColumnhitronDQoSControlRowStatus | read-create | current | The RowStatus interlock for the creation and deletion of a hitronDQoSControlTable entry. Any writable object in each row of the hitronDQoSControlTable can be m… |
| 1.3.6.1.4.1.8595.2.1.2.12 | TablehitronCmSpeedTestTable | not-accessible | current | This table allows configuration of RF speed test by iperf tool. |
| 1.3.6.1.4.1.8595.2.1.2.12.1 | RowhitronCmSpeedTestEntry | not-accessible | current | Allow configuration of RF speed test by iperf tool. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.1 | ColumnhitronCmServerMode | read-write | current | Select speed test mode |
| 1.3.6.1.4.1.8595.2.1.2.12.1.2 | ColumnhitronCmListenPort | read-write | current | set the listen port for the speed test |
| 1.3.6.1.4.1.8595.2.1.2.12.1.3 | ColumnhitronCmBufferLength | read-write | current | The buffer length definition for the UDP traffic test, in Bytes |
| 1.3.6.1.4.1.8595.2.1.2.12.1.4 | ColumnhitronCmTcpWindowSize | read-write | current | The TCP window size setting for TCP traffic test, in KBytes |
| 1.3.6.1.4.1.8595.2.1.2.12.1.5 | ColumnhitronCmRunSpeedTest | read-write | current | Setting to 'enable' is to start the speed test daemon. If the daemon is enabled, the read-back value is enable. Setting to 'disable' is to stop the speed test … |
| 1.3.6.1.4.1.8595.2.1.2.12.1.6 | ColumnhitronCmTestUploadSpeed | read-only | current | The upstream speed test result, in KBytes. It will keep the last result until the hitronCmRunSpeedTest is enabled. If hitronCmRunSpeedTest is disabled, this re… |
| 1.3.6.1.4.1.8595.2.1.2.12.1.7 | ColumnhitronCmTestDownloadSpeed | read-only | current | The downstream speed test result, in KBytes. It will keep the last result until the hitronCmRunSpeedTest is enabled. If hitronCmRunSpeedTest is disabled, this … |
| 1.3.6.1.4.1.8595.2.1.2.12.1.8 | ColumnhitronCmSpeedTestVersion | read-write | current | Set iperf version for speed test. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.9 | ColumnhitronCmSpeedTestBandwidth | read-write | current | Set bandwidth for speed test, in Mbits/sec. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.10 | ColumnhitronCmSpeedTestTime | read-write | current | Set time in seconds to transmit. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.11 | ColumnhitronCmSpeedTestClientMode | read-write | current | Select speed test mode for client mode. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.12 | ColumnhitronCmSpeedTestServer | read-create | current | Set the test server for client mode. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.13 | ColumnhitronCmSpeedTestInterface | read-write | current | Select interface for speed test. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.14 | ColumnhitronCmSpeedTestDownloadFile | read-create | current | Set the download file for http/ftp test mode. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.15 | ColumnhitronCmSpeedTestUploadFile | read-create | current | Set the upload file for http/ftp test mode. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.16 | ColumnhitronCmSpeedTestUploadFileSize | read-write | current | Set the upload file size (in bytes) for http/ftp test mode. |
| 1.3.6.1.4.1.8595.2.1.2.12.1.17 | ColumnhitronCmSpeedTestStatus | read-only | current | Speed test status. |
| 1.3.6.1.4.1.8595.2.1.2.13 | ScalarhitronDisplayIpInformation | read-write | current | This OID controls whether the status page displays IP information. Default: True. When set to False the <Cable Modem IP> block is not shown |
| 1.3.6.1.4.1.8595.2.1.2.14 | ScalarhitronDisplayCmConfig | read-write | current | When this OID is set to false, the CM configuration file name and the nework access rows in the web page are NOT displayed. |
| 1.3.6.1.4.1.8595.2.1.2.15 | ScalarhitronConsoleEnable | read-write | current | When this OID is set to true, the console for both the Uboot and Application is active and can be used |
| 1.3.6.1.4.1.8595.2.1.2.16 | ScalarhitronForceDOCSIS20 | read-write | current | If this flag is set to true, the CM would behave like a D2 CM even under a D3 environment. |
| 1.3.6.1.4.1.8595.2.1.2.17 | ScalarhitronDocsisMode | read-only | current | Display the CM DOCSIS opearation mode and Downstream and Upstream online number. For example, if it's 8x4 Full D3 locked, the value is 0100000000100010, i.e. 0… |
| 1.3.6.1.4.1.8595.2.1.2.18 | ScalarhitronMddIpModeOverride | read-write | current | hitronMddIpModeOverride is used to change the DHCP process mode. |
| 1.3.6.1.4.1.8595.2.1.2.19 | ScalarhitronMaxT3Count | read-write | current | This is controls MAX T3 count . |
| 1.3.6.1.4.1.8595.2.1.2.20 | ScalarhitronUsHighPowerPlusOffset | read-write | current | This OID is to extra US power beyond the DOCSIS spec. Its unit is in dBmv. |
| 1.3.6.1.4.1.8595.2.1.2.21 | NodehitronGuiDisplayCtrl | |||
| 1.3.6.1.4.1.8595.2.1.2.21.1 | ScalarhitronGuiDisplayCableStatus | read-write | current | This OID controls whether the cable status page would be displayed. Default: True. When set to False the whole cable status tab should not be displayed. |
| 1.3.6.1.4.1.8595.2.1.2.21.2 | ScalarhitronGuiDisplayIpInformation | read-write | current | This OID controls whether the cable status page displays IP information. Default: True. When set to False the <Cable Modem IP> block is not shown |
| 1.3.6.1.4.1.8595.2.1.2.21.3 | ScalarhitronGuiDisplayDsTune | read-write | current | When this OID is set to false, the downstream setting column in the cable status page is hidden and disabled. |
| 1.3.6.1.4.1.8595.2.1.2.21.4 | ScalarhitronGuiDisplayDsDisplay | read-write | current | When this OID is set to false, the downstream display table in the cable status page is hidden and disabled. |
| 1.3.6.1.4.1.8595.2.1.2.21.5 | ScalarhitronGuiDisplayUsTune | read-write | current | When this OID is set to false, the upstream setting column in the cable status page is hidden and disabled. |
| 1.3.6.1.4.1.8595.2.1.2.21.6 | ScalarhitronGuiDisplayUsDisplay | read-write | current | When this OID is set to false, the upstream display table in the cable status page is hidden and disabled. |
| 1.3.6.1.4.1.8595.2.1.2.21.7 | ScalarhitronVpnGUIVisible | read-write | current | This OID is to show/hide vpn webpage[2.hide 1.show]. |
| 1.3.6.1.4.1.8595.2.1.2.21.8 | ScalarhitronGuiDefaultLanguage | read-write | current | This OID is to set default language for GUI. |
| 1.3.6.1.4.1.8595.2.1.2.21.9 | ScalarhitronPassThroughGUIVisible | read-write | current | This OID is to show/hide passthrough webpage[2.hide 1.show]. |
| 1.3.6.1.4.1.8595.2.1.2.21.10 | ScalarhitronBasicGUIVisible | read-write | current | This OID is to show/hide basic webpage[2.hide 1.show]. |
| 1.3.6.1.4.1.8595.2.1.2.21.11 | ScalarhitronWanIpGUIVisible | read-write | current | This OID is to show/hide WanIp webpage[2.hide 1.show]. |
| 1.3.6.1.4.1.8595.2.1.2.21.12 | ScalarhitronCableGUIVisible | read-write | current | This OID is to show/hide Cable webpage[2.hide 1.show]. |
| 1.3.6.1.4.1.8595.2.1.2.22 | NodehitronPPTest | |||
| 1.3.6.1.4.1.8595.2.1.2.22.1 | NodehitronPPTestResult | |||
| 1.3.6.1.4.1.8595.2.1.2.22.1.1 | ScalarhitronPPTestBitsPerSecond | read-only | current | Get the speed in bits/s. |
| 1.3.6.1.4.1.8595.2.1.2.22.2 | NodehitronPPTestSettings | |||
| 1.3.6.1.4.1.8595.2.1.2.22.2.1 | ScalarhitronPPTestsrcIPAddr | read-write | current | Set source IP address. |
| 1.3.6.1.4.1.8595.2.1.2.22.2.2 | ScalarhitronPPTestDstPort | read-write | current | Set dest port. |
| 1.3.6.1.4.1.8595.2.1.2.22.2.3 | ScalarhitronPPTestspeedTestTime | read-write | current | Set speed test time, unit is second. |
| 1.3.6.1.4.1.8595.2.1.2.22.2.4 | ScalarhitronPPTestsrcIPv6Addr | read-write | current | Set source IPv6 address. |
| 1.3.6.1.4.1.8595.2.1.2.22.2.5 | ScalarhitronPPTestIPType | read-write | current | This object controls whether the test in IPv4 or IPv6 mode. In IPv6 mode, the OID hitronPPTestsrcIPv6Addr would take effect, and it would create the session wi… |
| 1.3.6.1.4.1.8595.2.1.2.22.2.100 | ScalarhitronPPTestApply | read-write | current | Start to create PP session. |
| 1.3.6.1.4.1.8595.2.1.2.23 | ScalarhitronBondingStatus | read-only | current | Display the CM DOCSIS opearation mode and Downstream and Upstream bonding status. 64 bit mask is used to identify status. For example, if CM is 24x8 Full D3, i… |
| 1.3.6.1.4.1.8595.2.1.2.24 | ScalarhitronCliPasswordControl | read-write | current | This object manages the password of CLI, always returns empty when reading. |
| 1.3.6.1.4.1.8595.2.1.2.25 | ScalarhitronCefdkVersionInfo | read-only | current | The cefdk version information which is used. |
| 1.3.6.1.4.1.8595.2.1.2.26 | ScalarhitronDBCControl | read-write | current | When this oid is set to TRUE, CM rejects DBC-REQ. |
| 1.3.6.1.4.1.8595.2.1.2.27 | NodehitronCmTftpBlockSizeEntry | |||
| 1.3.6.1.4.1.8595.2.1.2.27.1 | ScalarhitronCmTftpBlockSizeforIPV4 | read-write | current | The device MUST support two TFTP block size settings for the downloading of device firmware: one for when the device is operating in IPv4 mode and the other wh… |
| 1.3.6.1.4.1.8595.2.1.2.27.2 | ScalarhitronCmTftpBlockSizeforIPV6 | read-write | current | The device MUST support two TFTP block size settings for the downloading of device firmware: one for when the device is operating in IPv4 mode and the other wh… |
| 1.3.6.1.4.1.8595.2.1.2.28 | ScalarhitronDynamicCpeMaxIdleSec | read-write | current | Seconds of the idle time for dynamic cpe. When this value is 0 , that means cpe age out funcitons are disabled. When this value is -1, that means this code don… |
| 1.3.6.1.4.1.8595.2.1.2.29 | ScalarhitronCmWarmResetCount | read-only | current | It shows CM warm reset count. |
| 1.3.6.1.4.1.8595.2.1.2.30 | ScalarhitronCmColdResetCount | read-only | current | It shows CM cold reset count. |
| 1.3.6.1.4.1.8595.2.1.2.31 | ScalarhitronCmClearWarmColdResetCount | read-write | current | It clear CM warm reset count and cold reset count. |
| 1.3.6.1.4.1.8595.2.1.2.32 | ScalarhitronCmDebugOption37 | read-write | obsolete | This object is used to on/off debug option 37(DOCSIS_DBG_NO_D31_US_POWER_CONTROL). In order to get CDA-45 to deploy on CASA, Videotron need a MIB to control De… |
| 1.3.6.1.4.1.8595.2.1.2.33 | ScalarhitronCmD31mode | read-write | current | This object is used to turn on/off DOCSIS 3.1 mode. If there are D3.1 channels in testing in the field, but the customer DO NOT want the modem to lock on it, t… |
| 1.3.6.1.4.1.8595.2.1.2.34 | NodehitronSyslogCtrl | |||
| 1.3.6.1.4.1.8595.2.1.2.34.1 | ScalarhitronSyslogDstIPAddr | read-write | current | Set destination Ipv6 address. |
| 1.3.6.1.4.1.8595.2.1.2.34.2 | ScalarhitronSyslogDstPort | read-write | current | Set destination port. |
| 1.3.6.1.4.1.8595.2.1.2.34.3 | ScalarhitronSyslogProtocol | read-write | current | Selected protocol. |
| 1.3.6.1.4.1.8595.2.1.2.35 | ScalarhitronDBCRejectDsidDelete | read-write | current | When setting to TRUE, modem will reject DSID delete action in DBC requests. |
| 1.3.6.1.4.1.8595.2.1.2.36 | NodehitronSessionTimeoutCtrl | |||
| 1.3.6.1.4.1.8595.2.1.2.36.1 | ScalarhitronSessionGuiTimeoutMinute | read-write | current | Set web session timeout minute.The value range is from 1 to 120. |
| 1.3.6.1.4.1.8595.2.1.2.36.2 | ScalarhitronSessionSshdTimeoutMinute | read-write | current | Set sshd session timeout minute.The value Range is from 1 to 120. |
| 1.3.6.1.4.1.8595.2.1.2.37 | ScalarhitronAqmMode | read-write | current | This object is used to set AQM mode 1: enable AQM 2: disable AQM 3: follow AQM tlv value in cfg file |
| 1.3.6.1.4.1.8595.2.1.2.38 | ScalarhitronAqmLatency | read-write | current | This object is used to set AQM latency (millisecond). When this object is set to 0, the latency value in config file will be used. For other values, modem woul… |
| 1.3.6.1.4.1.8595.2.1.2.39 | ScalarhitronSetARMDDRTo256M | read-write | current | This OID is used to set DDR size assigned to ARM CPU from 128M to 256M. This OID is only valid for boards with 128M RAM for ARM and 384M for ATOM or 896M for A… |
| 1.3.6.1.4.1.8595.2.1.2.40 | ScalarhitronDiplexerControl | read-write | current | This OID is used to control diplexer to switch DS and US band. |
| 1.3.6.1.4.1.8595.2.1.2.41 | ScalarhitronCMPODSeed | read-write | current | This value is used as a seed to generate the POD string. |
| 1.3.6.1.4.1.8595.2.1.2.42 | ScalarhitronSNMPv1Enable | read-write | current | This OID allows to enable/disable SNMPv1 protocol |
| 1.3.6.1.4.1.8595.2.1.2.43 | ScalarhitronCMEnableRebootBehavior | read-write | current | This object is used to decide if rebooting after CMTS runs 'clear' command. 0: disable Reboot behavior 1: enable Rebbot behavior |
| 1.3.6.1.4.1.8595.2.1.2.44 | ScalarhitronCmD31OFDMmode | read-write | current | This object is used to turn on/off DOCSIS 3.1 Downstream OFDM Channel. |
| 1.3.6.1.4.1.8595.2.1.2.45 | ScalarhitronCmD31OFDMAmode | read-write | current | This object is used to turn on/off DOCSIS 3.1 Upstream OFDMA Port. |
| 1.3.6.1.4.1.8595.2.1.2.46 | ScalarhitronCmDefSetting4CLRRegion | read-write | current | Select region default setting for CLR. |
| 1.3.6.1.4.1.8595.2.1.2.47 | ScalarhitronCALA | read-write | current | Select vendor default setting |
| 1.3.6.1.4.1.8595.2.1.2.48 | ScalarhitronArgentina | read-write | current | Select SSID name default |
| 1.3.6.1.4.1.8595.2.1.2.49 | ScalarhitronForceT4Multiplier | read-write | current | Set T4 Multiplier for all ports, this value won't be saved to flash. After reboot, it will be default value 0. The value range is 0-10. |
| 1.3.6.1.4.1.8595.2.1.2.50 | ScalarhitronCmLastRebootReason | read-only | current | Show the last reboot reason and time. |
| 1.3.6.1.4.1.8595.2.1.2.51 | ScalarhitronTDoxAckSuppressionEnable | read-write | current | Enable Turbodox ACK suppression. |
| 1.3.6.1.4.1.8595.2.1.2.52 | ScalarhitronCMEnableAutoDiplexer | read-write | current | This object is used to decide if the CM will follow the MDD TLV9/21 from CMTS to switch its diplexer band 0: disable Auto Diplex Filter Switching behavior 1: e… |
| 1.3.6.1.4.1.8595.2.1.2.53 | ScalarhitronUsHighPowerExtended | read-write | current | This OID is for extended upstream transmit power (EUTP) within the DOCSIS spec. Its unit is Value: 0, 205-244 (units of one-quarter dB). |
| 1.3.6.1.4.1.8595.2.1.2.54 | ScalarhitronCmQam256MseLossValue | read-write | current | This object is used to change the value of QAM_256_MSE_LOSS_THRESHOLD. |
| 1.3.6.1.4.1.8595.2.1.2.55 | ScalarhitronCmQam64MseLossValue | read-write | current | This object is used to change the value of QAM_64_MSE_LOSS_THRESHOLD. |
| 1.3.6.1.4.1.8595.2.1.2.56 | ScalarhitronPPMaxThreshold | read-write | current | Get/Set MaxThreshold of Packet Processor. |
| 1.3.6.1.4.1.8595.2.1.2.57 | ScalarhitronCmDownstreamResetCerCounters | read-write | current | Resets the cer counters. |
| 1.3.6.1.4.1.8595.2.1.2.58 | ScalarhitronCmDefSetting4Millicom | read-write | current | Select vendor default setting for Millicom. |
| 1.3.6.1.4.1.8595.2.1.2.59 | ScalarhitronGREPassthroughEnable | read-write | current | Enable/Disbale GRE Passthrough. |
| 1.3.6.1.4.1.8595.2.1.2.60 | ScalarhitronExtendedPacketDbg | read-write | current | This object is used to change the value of DOCSIS_DBG_D31_DISABLE_EXTENDED_PACKET_LEN. |
| 1.3.6.1.4.1.8595.2.1.2.61 | ScalarhitronCmConfigTLV43Dot237 | read-write | current | TLV43.237 |
| 1.3.6.1.4.1.8595.2.1.2.62 | ScalarhitronPPSesTimeout | read-write | current | Get/Set SesTimeout(sec) of Packet Processor. |
| 1.3.6.1.4.1.8595.2.1.2.63 | ScalarhitronL2TPModeEnable | read-write | current | Enable/Disbale L2TP Mode. |
| 1.3.6.1.4.1.8595.2.1.2.64 | TablehitronDOCSISLanPortConfigTable | not-accessible | current | This table is used to configure the configuration of lan port. |
| 1.3.6.1.4.1.8595.2.1.2.64.1 | RowhitronDOCSISLanPortConfigEntry | not-accessible | current | Entry of table hitronDOCSISLanPortConfigTable |
| 1.3.6.1.4.1.8595.2.1.2.64.1.1 | ColumnhitronDOCSISLanPortConfigIndex | not-accessible | current | Lan Port index. |
| 1.3.6.1.4.1.8595.2.1.2.64.1.2 | ColumnhitronDOCSISLanPortSpeed | read-write | current | The Lan Port Speed value. |
| 1.3.6.1.4.1.8595.2.1.2.64.1.3 | ColumnhitronDOCSISLanPortDuplexMode | read-write | current | The Lan Port Duple mode value. |
| 1.3.6.1.4.1.8595.2.1.2.64.1.4 | ColumnhitronDOCSISLanPortAutoNego | read-write | current | The Lan Port Speed value. |
| 1.3.6.1.4.1.8595.2.1.2.65 | NodehitronL2VPNMacSwapLoopbackCtrl | |||
| 1.3.6.1.4.1.8595.2.1.2.65.1 | ScalarhitronL2VPNMacSwapLoopbackAddress | read-write | current | BSoD L2VPN loopback feature destination mac address. |
| 1.3.6.1.4.1.8595.2.1.2.65.2 | ScalarhitronL2VPNMacSwapLoopbackEnable | read-write | current | BSoD L2VPN loopback feature on/off. |
| 1.3.6.1.4.1.8595.2.1.2.66 | ScalarhitronResetFactoryExceptWiFi | read-write | current | Reset the unit to factory default, except the WiFi configuration. This will also wipe any learned golden frequencies and reset the unit to the state as from fa… |
| 1.3.6.1.4.1.8595.2.1.3 | NodehitronCmImageParameters | |||
| 1.3.6.1.4.1.8595.2.1.3.1 | TablehitronDeviceDloadTable | not-accessible | current | This table controls device download list for different HWID, Model and download server and download image filename. |
| 1.3.6.1.4.1.8595.2.1.3.1.1 | RowhitronDeviceDloadEntry | not-accessible | current | An entry describing a complete row for HW ID, HW Model, download server IP and download image filename. |
| 1.3.6.1.4.1.8595.2.1.3.1.1.1 | ColumnhitronDeviceDloadIndex | not-accessible | current | Index used to order the download device entries. |
| 1.3.6.1.4.1.8595.2.1.3.1.1.2 | ColumnhitronCVCp1 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.3 | ColumnhitronCVCp2 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.4 | ColumnhitronCVCp3 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.5 | ColumnhitronCVCp4 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.6 | ColumnhitronCVCp5 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.7 | ColumnhitronCVCp6 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.8 | ColumnhitronCVCp7 | read-create | current | This object is used to check against the CVC header in the signed CM image. It is part of the CVC header of the signed image. This item should combine sequenti… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.9 | ColumnhitronHardwareId | read-create | current | The Hardware ID which is used by the receiving device to check against its own harware ID. If the checking is failed, no image upgrade should be performed. The… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.10 | ColumnhitronHardwareModel | read-create | current | The Hardware model name which is used by the receiving device to check against its own harware model name. If the checking is failed, no image upgrade should b… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.11 | ColumnhitronSwServer | read-create | current | The tftp server IP address which is used for image upgrade. |
| 1.3.6.1.4.1.8595.2.1.3.1.1.12 | ColumnhitronSwFilename | read-create | current | The image filename which is used for image upgrade. |
| 1.3.6.1.4.1.8595.2.1.3.1.1.13 | ColumnhitronDeviceDloadStatus | read-create | current | Controls and reflects the status of rows in this table. Rows in this table may be created by either the create-and-go or create-and-wait paradigms. There is no… |
| 1.3.6.1.4.1.8595.2.1.3.1.1.14 | ColumnhitronIPv6SwServer | read-create | current | The IPv6 tftp server IP address which is used for image upgrade. For OID hitronSwServer and hitronIPv6SwServer, only one should be used. If both of them exist … |
| 1.3.6.1.4.1.8595.2.1.3.2 | ScalarhitronFlashActiveImage | read-only | current | This object display the current active image segamenet. |
| 1.3.6.1.4.1.8595.2.1.3.3 | TablehitronFlashImageTable | not-accessible | current | A list of images version and filename in flash. |
| 1.3.6.1.4.1.8595.2.1.3.3.1 | RowhitronFlashImageEntry | not-accessible | current | list entry for each image segament in flash. |
| 1.3.6.1.4.1.8595.2.1.3.3.1.1 | ColumnhitronFlashImageIndex | not-accessible | current | The image segament number. |
| 1.3.6.1.4.1.8595.2.1.3.3.1.2 | ColumnhitronFlashVersion | read-only | current | The software version in the indexed segament in the flash. |
| 1.3.6.1.4.1.8595.2.1.3.3.1.3 | ColumnhitronFlashFilename | read-only | current | The image filename in the indexed segament in the flash. |
| 1.3.6.1.4.1.8595.2.1.4 | NodehitronCmDoc30SetupReducedOORThreshold | |||
| 1.3.6.1.4.1.8595.2.1.4.1 | ScalarhitronSetReducedOORThreshold | read-write | current | When enabled, OOR threshold is set to 3 and the timeout to 1 second. When disabled, OOR threshold is set to 1000 packets and the timeout to 2 minutes per the M… |
| 1.3.6.1.4.1.8595.2.1.5 | NodehitronCmCefdkUpgrade | |||
| 1.3.6.1.4.1.8595.2.1.5.1 | ScalarhitronCefdkUpgradeServer | read-create | current | The tftp server IP address which is used for image upgrade. |
| 1.3.6.1.4.1.8595.2.1.5.2 | ScalarhitronCefdkUpgradeName | read-create | current | The image filename which is used for image upgrade. |
| 1.3.6.1.4.1.8595.2.1.5.3 | ScalarhitronCefdkUpgradeAdminStatus | read-write | current | If set to upgradeFromMgt(1), the device will initiate a TFTP or HTTP software image download. After successfully receiving an image, the device will set its st… |
| 1.3.6.1.4.1.8595.2.1.5.4 | ScalarhitronCefdkUpgradeOperStatus | read-only | current | InProgress(1) indicates that a TFTP or HTTP download is underway, either as a result of a version mismatch at provisioning or as a result of a upgradeFromMgt r… |
| 1.3.6.1.4.1.8595.2.1.6 | NodehitronCMReinitMacReason | |||
| 1.3.6.1.4.1.8595.2.1.6.1 | ScalarhitronReinitMacReason | read-only | current | This object display the last CM Reinit MAC Reason. The current list of CM Reinit MAC Reason is: DS_SCAN_FAIL, NO_UCDS, SCAN_NEXT, DBC, UCC, DS_AND_US_OVERRIDE,… |
| 1.3.6.1.4.1.8595.2.1.7 | NodehitronTr069Parameters | |||
| 1.3.6.1.4.1.8595.2.1.7.1 | ScalarhitronTr069Enable | read-write | current | Enable/Disable TR-069(CWMP) Server. |
| 1.3.6.1.4.1.8595.2.1.7.2 | ScalarhitronTr069AcsUrl | read-write | current | The URL of Auto Configuration Servers (ACS). |
| 1.3.6.1.4.1.8595.2.1.7.3 | ScalarhitronTr069AcsUser | read-write | current | The UserName of Auto Configuration Servers (ACS). |
| 1.3.6.1.4.1.8595.2.1.7.4 | ScalarhitronTr069AcsPassWord | read-write | current | The Password of Auto Configuration Servers (ACS). |
| 1.3.6.1.4.1.8595.2.1.8 | NodehitronD3CmCertificatesUpgrade | |||
| 1.3.6.1.4.1.8595.2.1.8.1 | ScalarhitronD3CmCertsUpgradeFilepath | read-write | current | The file path for CM certificates upgrade. The final full filename is the path + CM_MAC_Address.enc. If the value for this OID is NULL, then the full filename … |
| 1.3.6.1.4.1.8595.2.1.8.2 | ScalarhitronD3CmCertsUpgradeServerIpType | read-write | current | The IP type of the TFTP server used for CM certificates upgrade. |
| 1.3.6.1.4.1.8595.2.1.8.3 | ScalarhitronD3CmCertsUpgradeServer | read-write | current | The address of the TFTP server used for CM certificates upgrade. It can be IPv4 or IPv6 address. |
| 1.3.6.1.4.1.8595.2.1.8.4 | ScalarhitronD3CmCertsUpgradeTrigger | read-write | current | It is used to trigger CM certificates upgrade feature. When set it to true, trigger the feature. |
| 1.3.6.1.4.1.8595.2.1.8.5 | ScalarhitronD3CmCertsUpgradeCurrentVersion | read-only | current | It is used to show current CM certificates version. 2022: old certification, 2031: new certification |
| 1.3.6.1.4.1.8595.2.1.9 | NodehitronDocsOfdmChanParameters | |||
| 1.3.6.1.4.1.8595.2.1.9.1 | TablehitronDocsOfdmDsChanTable | not-accessible | current | This table describes the hitron CM's downstream OFDM channels. |
| 1.3.6.1.4.1.8595.2.1.9.1.1 | RowhitronDocsOfdmDsChanEntry | not-accessible | current | The conceptual row of hitronDocsOfdmDsChanTable. An entry exists in this table for each ifEntry with an ifType value of docsOfdmDownstream(277). |
| 1.3.6.1.4.1.8595.2.1.9.1.1.1 | ColumnhitronOfdmDsChanFirstActiveFreq | read-only | current | This attribute corresponds to the frequency of the first non-excluded subcarrier. |
| 1.3.6.1.4.1.8595.2.1.9.1.1.2 | ColumnhitronOfdmDsChanLastActiveFreq | read-only | current | This attribute corresponds to the frequency of the last non-excluded subcarrier. |
| 1.3.6.1.4.1.8595.2.1.9.1.1.3 | ColumnhitronOfdmDsChanHighestCurrModulation | read-only | current | This attribute represents the highest modulation in use. |
| 1.3.6.1.4.1.8595.2.1.9.2 | TablehitronDocsOfdmUsChanTable | not-accessible | current | This table describes the hitron CM's upstream OFDMA channels. |
| 1.3.6.1.4.1.8595.2.1.9.2.1 | RowhitronDocsOfdmUsChanEntry | not-accessible | current | The conceptual row of the hitronDocsOfdmUsChanTable. |
| 1.3.6.1.4.1.8595.2.1.9.2.1.1 | ColumnhitronOfdmUsChanFirstActiveFreq | read-only | current | This attribute corresponds to the frequency of the first non-excluded subcarrier. |
| 1.3.6.1.4.1.8595.2.1.9.2.1.2 | ColumnhitronOfdmUsChanLastActiveFreq | read-only | current | This attribute corresponds to the frequency of the last non-excluded subcarrier. |
| 1.3.6.1.4.1.8595.2.1.9.2.1.3 | ColumnhitronOfdmUsChanHighestCurrModulation | read-only | current | This attribute represents the highest modulation in use. |
| 1.3.6.1.4.1.8595.2.1.10 | NodehitronCmVendorAdditionalInfo | |||
| 1.3.6.1.4.1.8595.2.1.10.1 | NodehitronCmInterface | |||
| 1.3.6.1.4.1.8595.2.1.10.1.1 | ScalarhitronCmLanPortExtswitch | read-only | current | The Lan port<Extswitch> chip infomation |
| 1.3.6.1.4.1.8595.2.1.11 | NodehitronCmDocsisDebugOptionSetup | |||
| 1.3.6.1.4.1.8595.2.1.11.1 | ScalarhitrontCmDocsisDebugOptionEnable | read-write | current | It is used to enable CM DOCSIS debug option, Value is debug option number. |
| 1.3.6.1.4.1.8595.2.1.11.2 | ScalarhitrontCmDocsisDebugOptionDisable | read-write | current | It is used to disable CM DOCSIS debug option, Value is debug option number. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| SnmpAdminString | OCTET STRING (SIZE (0..255)) | current | An octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an oct… |