INTEL-EXPRESS110-MIB
242 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.343.2.2.1 | Nodeexpress110 | |||
| 1.3.6.1.4.1.343.2.2.1.0 | NodeutilizationThresholdExceeded | Utilization rate in last rptrSegmentUtilizationTrapPeriod exceeded rptrSegmentUtilizationTrapThreshold. | ||
| 1.3.6.1.4.1.343.2.2.1.1 | NodecollisionThresholdExceeded | Collisions in last rptrSegmentCollisionTrapPeriod exceeded rptrSegmentCollisionTrapThreshold. | ||
| 1.3.6.1.4.1.343.2.2.1.1 | ScalarhubNumberofStackedChassis | read-only | mandatory | Displays the total number of chassis in the stack. |
| 1.3.6.1.4.1.343.2.2.1.2 | NodeconfigurationChange | A chassis was added to the stack or removed, a chassis lost power, a module was reset or powered on, or, a repeater module changed speeds. | ||
| 1.3.6.1.4.1.343.2.2.1.2 | ScalarhubDescriptionString | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.3 | ScalarhubStackReset | read-write | mandatory | Resets all modules in all of the chassis in the stack. |
| 1.3.6.1.4.1.343.2.2.1.3 | NodetBrdgBufferFull | Buffer full rate in last tBrdgPeriod exceeded tBrdgThrshld. | ||
| 1.3.6.1.4.1.343.2.2.1.4 | NodechassisRPSActive | The power supply has failed and the optional Redundant Power Supply for this chassis has activated. | ||
| 1.3.6.1.4.1.343.2.2.1.4 | ScalarhubLCDModeVariable | read-write | mandatory | Sets the type of information displayed on the Management Module's LCD when in Sleep Mode. sysContact, sysLocation, and sysName are user-definable. Traps shows … |
| 1.3.6.1.4.1.343.2.2.1.5 | ScalarhubLCDSleepText | read-write | mandatory | Sets user-defined text to be displayed by the LCD when in Sleep Mode. For example, you may want the name and phone number of a contact person to display on the… |
| 1.3.6.1.4.1.343.2.2.1.5 | NodeportSecurityViolation | An ethernet frame with an unauthorized source MAC address was detected on this port and the port has been disabled. | ||
| 1.3.6.1.4.1.343.2.2.1.6 | ScalarhubLCDSleepTime | read-write | mandatory | Sets the number of minutes before the LCD goes into Sleep Mode. If an LCD button isn't pressed for the time specified, the LCD goes into Sleep Mode and display… |
| 1.3.6.1.4.1.343.2.2.1.6 | NodemgmtSwitchedToBackupMgmt | Primary management module failed and switched to backup module. The value associated is the hub number of the active management module. | ||
| 1.3.6.1.4.1.343.2.2.1.7 | NodebridgeConfigChangeEvent | The trap is sent whenever a stack's bridge configuration is changed. The value associated is the hub number of the active bridge. | ||
| 1.3.6.1.4.1.343.2.2.1.7 | ScalarhubRFC1516Segment | read-write | mandatory | Sets which segment the standard repeater MIB (RFC1516) returns counters for. The standard repeater MIB doesn't support two segments at the same time. |
| 1.3.6.1.4.1.343.2.2.1.8 | NodebridgeConfigNoBridgeEvent | The trap is sent whenever a stack without a bridge warning | ||
| 1.3.6.1.4.1.343.2.2.1.8 | TablechassisConfigTable | not-accessible | mandatory | Configuration information at the chassis level. |
| 1.3.6.1.4.1.343.2.2.1.8.1 | RowchassisConfigEntry | not-accessible | mandatory | A table entry, containing configuration information about a single chassis. |
| 1.3.6.1.4.1.343.2.2.1.8.1.1 | ColumnchassisConfigTableIndex | read-only | mandatory | Chassis number in the stack. This object refers to the number in the example below. Example: chassisConfigTableIndex.1 This example refers to chassis 1 of the … |
| 1.3.6.1.4.1.343.2.2.1.8.1.2 | ColumnchassisSegmentMode | read-write | mandatory | Sets/reports the repeater segment the chassis ports participate in. For chassis which do not support port speed autosensing, only 'segment1' or 'segment2' can … |
| 1.3.6.1.4.1.343.2.2.1.8.1.3 | ColumnchassisReset | read-write | mandatory | Resets all modules in the selected chassis. |
| 1.3.6.1.4.1.343.2.2.1.8.1.4 | ColumnchassisRPSState | read-only | mandatory | The state of the optional Redundant Power Supply connected to the chassis. standby means the RPS is actively backing up the chassis. active means the chassis p… |
| 1.3.6.1.4.1.343.2.2.1.8.1.5 | ColumnchassisIsolate | read-write | mandatory | The isolated or unisolates the hub from the backplane channel. |
| 1.3.6.1.4.1.343.2.2.1.9 | TablemoduleConfigStatusTable | not-accessible | mandatory | Configuration and status information at the module level. |
| 1.3.6.1.4.1.343.2.2.1.9 | NodeportlinkChangeEvent | The trap is sent whenever the link state of a port changes from link up to link down or from link down to link up | ||
| 1.3.6.1.4.1.343.2.2.1.9.1 | RowmoduleConfigStatusEntry | not-accessible | mandatory | A table entry, containing configuration and status information about a single module. |
| 1.3.6.1.4.1.343.2.2.1.9.1.1 | ColumnmoduleChassisIndex | read-only | mandatory | Chassis number in the stack. This object refers to the first number in the example below. Example: moduleChassisIndex.1.1 The first number is the chassis (hub)… |
| 1.3.6.1.4.1.343.2.2.1.9.1.2 | ColumnmoduleIndex | read-only | mandatory | Module number in the chassis. This object refers to the second number in the example below. Example: moduleChassisIndex.1.1 The first number is the chassis (hu… |
| 1.3.6.1.4.1.343.2.2.1.9.1.3 | ColumnmoduleType | read-only | mandatory | The module type. The base ports of a 12- or 24-port hub are considered modules. For example, hubTXports12 are ports 1-12 on a 12-port hub. bridge is an externa… |
| 1.3.6.1.4.1.343.2.2.1.9.1.4 | ColumnmoduleUserAssignedType | read-write | mandatory | User-definable information about the type of the module. Manufacturer assigns a default value. |
| 1.3.6.1.4.1.343.2.2.1.9.1.5 | ColumnmoduleUserAssignedNumber | read-write | mandatory | User-definable information about the module. Blank by default. |
| 1.3.6.1.4.1.343.2.2.1.9.1.6 | ColumnmoduleUserAssignedName | read-write | mandatory | User-definable information about the module. Blank by default. |
| 1.3.6.1.4.1.343.2.2.1.9.1.7 | ColumnmoduleSizeofROM | read-only | mandatory | Displays the module's ROM size. |
| 1.3.6.1.4.1.343.2.2.1.9.1.8 | ColumnmoduleSizeofRAM | read-only | mandatory | Displays the module's RAM size. |
| 1.3.6.1.4.1.343.2.2.1.9.1.9 | ColumnmoduleHWDescription | read-only | mandatory | Displays the CPU type and flash capacity. |
| 1.3.6.1.4.1.343.2.2.1.9.1.10 | ColumnmoduleAgentSWVersion | read-only | mandatory | Displays the module's agent software version. Each module has software which contributes to the SNMP agent's functionality. The Management Module version is th… |
| 1.3.6.1.4.1.343.2.2.1.9.1.11 | ColumnmoduleBootSWVersion | read-only | mandatory | Displays the module's boot software version. |
| 1.3.6.1.4.1.343.2.2.1.9.1.12 | ColumnmoduleManufacturingInfo | read-only | mandatory | Displays the manufacturer-assigned hardware description. |
| 1.3.6.1.4.1.343.2.2.1.9.1.13 | ColumnmoduleTotalPortCount | read-only | mandatory | Displays the total number of ports in the module. This can be: 14 = a 12-port hub (12 base ports plus 2 expansion modules) 16 = a 12-port hub with an internal … |
| 1.3.6.1.4.1.343.2.2.1.9.1.14 | ColumnmoduleExternalPortCount | read-only | mandatory | Number of external ports in the module. |
| 1.3.6.1.4.1.343.2.2.1.9.1.15 | ColumnmoduleSegmentLockout | read-write | mandatory | Prevents the hub speed from being changed by either a management station and/or the Change speed button on the front of a hub. Only nButtonnMgmt is valid for e… |
| 1.3.6.1.4.1.343.2.2.1.9.1.16 | ColumnmoduleLEDInfo | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.17 | ColumnmoduleLastErrorID | read-write | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.18 | ColumnmoduleMediaDevicesReset | read-write | mandatory | Performs a physical layer reset of the module. Use this reset if ports lock-up on an individual hub. |
| 1.3.6.1.4.1.343.2.2.1.9.1.19 | ColumnmoduleImageFileSource | read-write | mandatory | Sets the IP address of the device that transfers the image file to the module. The image filename is specified by the moduleImageFileName object. The moduleIma… |
| 1.3.6.1.4.1.343.2.2.1.9.1.20 | ColumnmoduleImageFileName | read-write | mandatory | Sets the image filename contained on the device specified by the moduleImageFileSource object. The moduleImageDownloadControl object starts and stops the downl… |
| 1.3.6.1.4.1.343.2.2.1.9.1.21 | ColumnmoduleImageDownloadControl | read-write | mandatory | Starts and stops the image file download process to the module. Use the moduleImageFileSource to set the IP address of the device that contains image file. Use… |
| 1.3.6.1.4.1.343.2.2.1.9.1.22 | ColumnmoduleImageDownloadStatus | read-only | mandatory | Displays the Management Module's image file download status. If error appears, use the moduleImageFileSource, moduleImageFileName, and moduleImageDownloadContr… |
| 1.3.6.1.4.1.343.2.2.1.9.1.23 | ColumnmoduleOperationalStatus | read-only | mandatory | Current operational state of the module. |
| 1.3.6.1.4.1.343.2.2.1.9.1.24 | ColumnmoduleUptime | read-only | mandatory | Time since the module was last reset. |
| 1.3.6.1.4.1.343.2.2.1.9.1.25 | ColumnmoduleReset | read-write | mandatory | Resets the module. |
| 1.3.6.1.4.1.343.2.2.1.9.1.26 | ColumnmoduleAllPortLEDInfo | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.27 | ColumnmoduleAllPortAdminStatus | read-write | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.28 | ColumnmoduleAllPortOperStatus | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.29 | ColumnmoduleAllPortSpeed | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.30 | ColumnmoduleAllPortSpeedInfo | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.31 | ColumnmoduleSegmentMode | read-write | mandatory | Sets/reports the repeater segment the module ports participate in. For modules which do not support automatic port speed selection, only 'segment1' or 'segment… |
| 1.3.6.1.4.1.343.2.2.1.9.1.32 | ColumnmoduleAllPortLinkPartnerInfo | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.33 | ColumnmoduleAllPortCounterReset | read-write | mandatory | Resets all the port counters in the module to zero. This includes all traffic statistics (packet count, etc.) and error counts. |
| 1.3.6.1.4.1.343.2.2.1.9.1.34 | ColumnmoduleAllPortTimeSinceLinkChange | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.9.1.35 | ColumnmodulePersistentMemoryReset | read-write | mandatory | Reset contents of persistent memory objects to factory defaults. Persistent memory object are settings that are saved even after the module is reset or power-c… |
| 1.3.6.1.4.1.343.2.2.1.10 | TableportConfigTable | not-accessible | mandatory | Configuration information at the Port level. |
| 1.3.6.1.4.1.343.2.2.1.10 | NodeportSpeedChangeEvent | The trap is sent whenever the speed status of a port changes from link up to link down or from link down to link up | ||
| 1.3.6.1.4.1.343.2.2.1.10.1 | RowportConfigEntry | not-accessible | mandatory | A table entry, containing configuration information about a single port. |
| 1.3.6.1.4.1.343.2.2.1.10.1.1 | ColumnportChassisIndex | read-only | mandatory | Chassis number in stack. This object refers to the first number in the example below. Example: portChassisIndex.1.1.9 The first number is the chassis. The seco… |
| 1.3.6.1.4.1.343.2.2.1.10.1.2 | ColumnportModuleIndex | read-only | mandatory | Module number in the chassis. This object refers to the second number in the example below. Example: portModuleIndex.1.1.9 The first number is the chassis. The… |
| 1.3.6.1.4.1.343.2.2.1.10.1.3 | ColumnportIndex | read-only | mandatory | Port number in the module. This object refers to the third number in the example below. Example: portChassisIndex 1.1.9 The first number is the chassis. The se… |
| 1.3.6.1.4.1.343.2.2.1.10.1.4 | ColumnportType | read-only | mandatory | Displays the selected port's capabilities. internalHalfDuplex is the expansion module's internal connection to a port in the hub. |
| 1.3.6.1.4.1.343.2.2.1.10.1.5 | ColumnportAdminStatus | read-write | mandatory | Enables or disables the selected port. Disabled ports will not be able to establish a link to a device. Disabled ports remain disabled until re-enabled. |
| 1.3.6.1.4.1.343.2.2.1.10.1.6 | ColumnportOperStatus | read-only | mandatory | Displays the current link status of the port. Operational means a port has established a link to a device. Notoperational means the port does not have a link e… |
| 1.3.6.1.4.1.343.2.2.1.10.1.7 | ColumnportJabber | read-only | mandatory | Jabber state of the port. Failure means the device attached to the port caused the hub's jabber lock-up protection to turn on. Check the device attached to the… |
| 1.3.6.1.4.1.343.2.2.1.10.1.8 | ColumnportLinkPartnerInfo | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.10.1.9 | ColumnportLEDInfo | read-only | mandatory | Bitfield used by SNMP application. |
| 1.3.6.1.4.1.343.2.2.1.10.1.10 | ColumnportTimeSinceLastLinkChange | read-only | mandatory | Time since the last link status change. |
| 1.3.6.1.4.1.343.2.2.1.10.1.11 | ColumnportAllCountersReset | read-write | mandatory | Resets all counters for ports to zero. This includes all traffic statistics (packet count, etc.) and error counts. |
| 1.3.6.1.4.1.343.2.2.1.10.1.12 | ColumnportReset | read-write | mandatory | Reset the port at the media level. |
| 1.3.6.1.4.1.343.2.2.1.10.1.13 | ColumnportLastErrorID | read-only | mandatory | Type of last error that occurred on the port since the last link status change. badPhy is a hardware problem with the hub port. polarity means there's a cablin… |
| 1.3.6.1.4.1.343.2.2.1.10.1.14 | ColumnportSegmentAdminMode | read-write | mandatory | For ports that have the ability to be set independent of the hub or module they reside in, this object allows setting the port to 'segment1', 'segment2', or 'a… |
| 1.3.6.1.4.1.343.2.2.1.10.1.15 | ColumnportSegmentOperStatus | read-only | mandatory | Reports the port's segment assignment. 'none' indicates the port has a portSegmentAdminMode of 'auto' and has not negotiated a link speed setting with a device. |
| 1.3.6.1.4.1.343.2.2.1.10.1.16 | ColumnportLinkSpeed | read-only | mandatory | The operational speed of this port when linked. Ports which do not have a link report 'none'. |
| 1.3.6.1.4.1.343.2.2.1.10.1.17 | ColumnportSecureAdminMode | read-write | mandatory | Causes a port to be administratively disabled if an un-authorized MAC address is detected as having transmitted a frame into this hub port. A trap is also gene… |
| 1.3.6.1.4.1.343.2.2.1.10.1.18 | ColumnportSecureMAC | read-write | mandatory | Specifies the authorized MAC address for this port if portSecureAdminMode is set to portSecurityOn. |
| 1.3.6.1.4.1.343.2.2.1.10.1.19 | ColumnportLinkTestState | read-write | mandatory | The current setting of link test function for the port. When disable, a port will no longer be disconnected due to link fail. When enable, the port will only r… |
| 1.3.6.1.4.1.343.2.2.1.10.1.20 | ColumnportLinkTestStatusTrapCtrl | read-write | mandatory | This object indicates whether a trap should be generated when the link state changes. |
| 1.3.6.1.4.1.343.2.2.1.10.1.21 | ColumnportSpeedStatusTrapCtrl | read-write | mandatory | This object indicates whether a trap should be generated when the speed status changes. |
| 1.3.6.1.4.1.343.2.2.1.10.1.22 | ColumnportPolarityStatus | read-only | mandatory | The current polarity status of this port. |
| 1.3.6.1.4.1.343.2.2.1.11 | TablerptrSegmentConfigTable | not-accessible | mandatory | Repeater configuration information at the segment level. |
| 1.3.6.1.4.1.343.2.2.1.11.1 | RowrptrSegmentConfigEntry | not-accessible | mandatory | A table entry, containing repeater configuration information about a single segment. |
| 1.3.6.1.4.1.343.2.2.1.11.1.1 | ColumnrptrSegmentConfigIndex | read-only | mandatory | Index into this table is rptrSegmentConfigIndex. Any configuration changes apply to all repeater ports participating in the segment. If a stack does not have a… |
| 1.3.6.1.4.1.343.2.2.1.11.1.2 | ColumnrptrSegmentOperationalStatus | read-only | mandatory | Displays the operational status of the segment. |
| 1.3.6.1.4.1.343.2.2.1.11.1.3 | ColumnrptrSegmentZeroCounters | read-write | mandatory | Resets all repeater per-port counters of the repeater modules in the segment. The read value is always notreset. |
| 1.3.6.1.4.1.343.2.2.1.11.1.4 | ColumnrptrSegmentReset | read-write | mandatory | Performs a cold-reset of all repeater modules in the segment. (RFC2108 rptrInfoReset) |
| 1.3.6.1.4.1.343.2.2.1.11.1.5 | ColumnrptrSegmentResetMedia | read-write | mandatory | Performs a media layer reset of all repeater modules in the segment. |
| 1.3.6.1.4.1.343.2.2.1.11.1.6 | ColumnrptrSegmentPartitionThreshold | read-write | mandatory | The number of consecutive collisions that will cause a port to autopartition. Note that this sets the value for all repeaters in the segment. |
| 1.3.6.1.4.1.343.2.2.1.11.1.7 | ColumnrptrSegmentNonDisruptTest | read-write | mandatory | Performs a self-test of all repeater modules in the segment. |
| 1.3.6.1.4.1.343.2.2.1.11.1.8 | ColumnrptrSegmentUtilizationTrapThreshold | read-write | mandatory | If the utilization rate exceeds this value, a trap is sent. Use 0 to disable. This trap is based on the utilization rate over the last rptrSegmentUtilizationTr… |
| 1.3.6.1.4.1.343.2.2.1.11.1.9 | ColumnrptrSegmentCollisionTrapThreshold | read-write | mandatory | If the number of collisions exceeds this value, a trap is sent. Use 0 to disable. This trap is based on the number of collision in the last rptrSegmentCollisio… |
| 1.3.6.1.4.1.343.2.2.1.11.1.10 | ColumnrptrSegmentUtilizationTrapPeriod | read-write | mandatory | Time period (in minutes) that segment utilization must exceed the trap threshold value to generate a trap. |
| 1.3.6.1.4.1.343.2.2.1.11.1.11 | ColumnrptrSegmentCollisionTrapPeriod | read-write | mandatory | Time period (in minutes) that segment collisions must exceed the trap threshold value to generate a trap. |
| 1.3.6.1.4.1.343.2.2.1.11.1.12 | ColumnrptrSegmentSpeed | read-only | mandatory | The speed of the ports within the segment. |
| 1.3.6.1.4.1.343.2.2.1.12 | TablerptrSegmentStatTable | not-accessible | mandatory | Repeater status information at the segment level. |
| 1.3.6.1.4.1.343.2.2.1.12.1 | RowrptrSegmentStatEntry | not-accessible | mandatory | A table entry, containing repeater status information about a single repeater. |
| 1.3.6.1.4.1.343.2.2.1.12.1.1 | ColumnrptrSegmentStatIndex | read-only | mandatory | Selects the 10Mbps or 100Mbps segment. |
| 1.3.6.1.4.1.343.2.2.1.12.1.2 | ColumnrptrSegmentTotalFrames | read-only | mandatory | The number of frames detected without errors. Includes unicast, broadcast, and multicast frames. Does not include frames received with frames too long, runt, F… |
| 1.3.6.1.4.1.343.2.2.1.12.1.3 | ColumnrptrSegmentTotalOctets | read-only | mandatory | The number of octets (bytes) contained in frames received that had no errors. This includes octets in unicast, broadcast, and multicast frames. It also include… |
| 1.3.6.1.4.1.343.2.2.1.12.1.4 | ColumnrptrSegmentTotalErrors | read-only | mandatory | The total number of errors detected. Total errors include FCS errors, alignment errors, frame too long, short events, late events, very long event, and rate mi… |
| 1.3.6.1.4.1.343.2.2.1.12.1.5 | ColumnrptrSegmentTotalCollisions | read-only | mandatory | Sum of all collisions in this segment. (RFC2108 rptrMonTxCollisions) |
| 1.3.6.1.4.1.343.2.2.1.12.1.6 | ColumnrptrSegmentPartitionedPorts | read-only | mandatory | Total number of present and enabled, but autopartitioned ports. (RFC2108 rptrInfoPartitionedPorts) |
| 1.3.6.1.4.1.343.2.2.1.12.1.7 | ColumnrptrSegmentHealthText | read-only | mandatory | Description of current health of all repeaters in the segment. (RFC2108 rptrHealthText) |
| 1.3.6.1.4.1.343.2.2.1.12.1.8 | ColumnrptrSegmentUtilization | read-only | mandatory | The utilization rate over the last one second. |
| 1.3.6.1.4.1.343.2.2.1.13 | TablerptrModuleStatTable | not-accessible | mandatory | ***** Deprecated and replaced by rptrChassisSegmentStatTable ***** Repeater status information at the Module level. |
| 1.3.6.1.4.1.343.2.2.1.13.1 | RowrptrModuleStatEntry | not-accessible | mandatory | ***** Deprecated and replaced by rptrChassisSegmentStatEntry ***** A table entry, containing repeater status information about a single module. |
| 1.3.6.1.4.1.343.2.2.1.13.1.1 | ColumnrptrModuleIndex | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentIndex ***** This index is the chassis number in the stack. The chassis at the top of the stack is number 1. |
| 1.3.6.1.4.1.343.2.2.1.13.1.2 | ColumnrptrModuleTotalFrames | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentTotalFrames ***** The number of frames detected without errors. Includes unicast, broadcast, and multicast f… |
| 1.3.6.1.4.1.343.2.2.1.13.1.3 | ColumnrptrModuleTotalOctets | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentTotalOctets ***** The number of octets (bytes) contained in frames received that had no errors. This include… |
| 1.3.6.1.4.1.343.2.2.1.13.1.4 | ColumnrptrModuleTotalErrors | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentTotalErrors ***** The total number of errors detected. Total errors include FCS errors, alignment errors, fr… |
| 1.3.6.1.4.1.343.2.2.1.13.1.5 | ColumnrptrModuleFCSErrors | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentFCSErrors ***** The number of frames detected that are free of partial octets and do not pass the FCS check.… |
| 1.3.6.1.4.1.343.2.2.1.13.1.6 | ColumnrptrModuleAlignmentErrors | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentAlignmentErrors ***** The number of frames detected that contain partial octets and do not pass the FCS chec… |
| 1.3.6.1.4.1.343.2.2.1.13.1.7 | ColumnrptrModuleFrameTooLongs | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentFrameTooLongs ***** The number of frames detected that exceed the maximum permitted frame size. |
| 1.3.6.1.4.1.343.2.2.1.13.1.8 | ColumnrptrModuleShortEvents | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentShortEvents ***** The number of fragments detected with ActivityDuration less than ShortEventMaxTime (greate… |
| 1.3.6.1.4.1.343.2.2.1.13.1.9 | ColumnrptrModuleRunts | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentRunts ***** The number of frames detected that are less than the minimum permitted frame size of 64 octets b… |
| 1.3.6.1.4.1.343.2.2.1.13.1.10 | ColumnrptrModuleCollisions | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentCollisions ***** Sum of all collisions for all ports in this repeater module. |
| 1.3.6.1.4.1.343.2.2.1.13.1.11 | ColumnrptrModuleLateEvents | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentLateEvents ***** The number of collisions detected after the allowable detection period. Usually indicates a… |
| 1.3.6.1.4.1.343.2.2.1.13.1.12 | ColumnrptrModuleVeryLongEvents | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentVeryLongEvents ***** The number of times MAU jabber lockup protection (MJLP) was detected due to transmissio… |
| 1.3.6.1.4.1.343.2.2.1.13.1.13 | ColumnrptrModuleDataRateMismatches | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentDataRateMismatches ***** A count of the occurrences of out-of-specification bit rates. This indicates the nu… |
| 1.3.6.1.4.1.343.2.2.1.13.1.14 | ColumnrptrModuleAutoPartitions | read-only | mandatory | ***** Deprecated and replaced by rptrChassisSegmentAutoPartitions ***** The number of times this port was automatically partitioned. This condition occurs when… |
| 1.3.6.1.4.1.343.2.2.1.14 | TablerptrPortStatTable | not-accessible | mandatory | Repeater status information at the port level. |
| 1.3.6.1.4.1.343.2.2.1.14.1 | RowrptrPortStatEntry | not-accessible | mandatory | A table entry, containing repeater status information about a single port. |
| 1.3.6.1.4.1.343.2.2.1.14.1.1 | ColumnrptrPortChassisIndex | read-only | mandatory | Chassis number in stack. The chassis at the top is number 1. |
| 1.3.6.1.4.1.343.2.2.1.14.1.2 | ColumnrptrPortIndex | read-only | mandatory | Port number in the module. |
| 1.3.6.1.4.1.343.2.2.1.14.1.3 | ColumnrptrPortPartitionState | read-only | mandatory | Indicates a port's current autopartitioned state. (RFC2108 rptrPortAutoPartitionState) |
| 1.3.6.1.4.1.343.2.2.1.14.1.4 | ColumnrptrPortReadableFrames | read-only | mandatory | The number of frames detected without errors. Includes unicast, broadcast, and multicast frames. Does not include frames received with frames too long, runt, F… |
| 1.3.6.1.4.1.343.2.2.1.14.1.5 | ColumnrptrPortReadableOctets | read-only | mandatory | The number of octets (bytes) contained in frames received that had no errors. This includes octets in unicast, broadcast, and multicast frames. It also include… |
| 1.3.6.1.4.1.343.2.2.1.14.1.6 | ColumnrptrPortFcsErrors | read-only | mandatory | The number of frames detected that are free of partial octets and do not pass the FCS check. Usually caused by adapter underrun (when the adapter can't get eno… |
| 1.3.6.1.4.1.343.2.2.1.14.1.7 | ColumnrptrPortAlignmentErrors | read-only | mandatory | The number of frames detected that contain partial octets and do not pass the FCS check. (RFC2108 rptrMonitorPortAlignmentErrors) |
| 1.3.6.1.4.1.343.2.2.1.14.1.8 | ColumnrptrPortFrameTooLongs | read-only | mandatory | The number of frames detected that exceed the maximum permitted frame size of 1518 octets. (RFC2108 rptrMonitorPortFrameTooLongs) |
| 1.3.6.1.4.1.343.2.2.1.14.1.9 | ColumnrptrPortShortEvents | read-only | mandatory | The number of fragments detected with ActivityDuration less than ShortEventMaxTime (greater than 74 bit times and less than 82 bit times). Usually indicates a … |
| 1.3.6.1.4.1.343.2.2.1.14.1.10 | ColumnrptrPortRunts | read-only | mandatory | The number of frames detected that are less than the minimum permitted frame size of 64 octets but have a good FCS. Runts usually indicate collision fragments,… |
| 1.3.6.1.4.1.343.2.2.1.14.1.11 | ColumnrptrPortCollisions | read-only | mandatory | The number of collisions detected on a port. (RFC2108 rptrMonitorPortCollisions) |
| 1.3.6.1.4.1.343.2.2.1.14.1.12 | ColumnrptrPortLateEvents | read-only | mandatory | The number of collisions detected after the allowable detection period. Usually indicates a network topology problem, such as daisy-chaining Class I 100Mbps hu… |
| 1.3.6.1.4.1.343.2.2.1.14.1.13 | ColumnrptrPortVeryLongEvents | read-only | mandatory | The number of times MAU jabber lockup protection (MJLP) was detected due to transmission of data that exceeded 5 msec in duration (octet count greater than max… |
| 1.3.6.1.4.1.343.2.2.1.14.1.14 | ColumnrptrPortDataRateMismatches | read-only | mandatory | A count of the occurrences of out-of-specification bit rates. This indicates the number of times the FIFO buffer overruns or underruns due to transmission rate… |
| 1.3.6.1.4.1.343.2.2.1.14.1.15 | ColumnrptrPortAutoPartitions | read-only | mandatory | The number of times this port was automatically partitioned. This condition occurs when 64 consecutive collisions are detected on the port. These collisions ar… |
| 1.3.6.1.4.1.343.2.2.1.14.1.16 | ColumnrptrPortTotalErrors | read-only | mandatory | The total number of errors detected. Total errors include FCS errors, alignment errors, frame too long, short events, late events, very long event, rate mismat… |
| 1.3.6.1.4.1.343.2.2.1.14.1.17 | ColumnrptrPortLastMACAddress | read-only | mandatory | The source address of the last readable frame received by this port. If no frames have been received on this port, the length of the returned DisplayString is … |
| 1.3.6.1.4.1.343.2.2.1.14.1.18 | ColumnrptrPortNumberofMACAddressChanges | read-only | mandatory | The number of times that the value of rptrPortLastMACAddress has changed. The typical value for this port is 1, meaning the value of rptrPortLastMACAddress cha… |
| 1.3.6.1.4.1.343.2.2.1.14.1.19 | ColumnrptrPortSymbolErrors | read-only | mandatory | This counter is incremented by one each time a valid length packet was received at the port and there was at least one occurrence of an invalid data symbol. Th… |
| 1.3.6.1.4.1.343.2.2.1.15 | TablerptrChassisSegmentStatTable | not-accessible | mandatory | Repeater status information by segment at the chassis level. |
| 1.3.6.1.4.1.343.2.2.1.15.1 | RowrptrChassisSegmentStatEntry | not-accessible | mandatory | A table entry, containing repeater status information about a single chassis and segment. |
| 1.3.6.1.4.1.343.2.2.1.15.1.1 | ColumnrptrChassisIndex | read-only | mandatory | This index is the chassis number in the stack. The chassis at the top of the stack is number 1. |
| 1.3.6.1.4.1.343.2.2.1.15.1.2 | ColumnrptrChassisSegmentIndex | read-only | mandatory | This index is the segment number in the stack. |
| 1.3.6.1.4.1.343.2.2.1.15.1.3 | ColumnrptrChassisSegmentTotalFrames | read-only | mandatory | The number of frames detected without errors. Includes unicast, broadcast, and multicast frames. Does not include frames received with frames too long, runt, F… |
| 1.3.6.1.4.1.343.2.2.1.15.1.4 | ColumnrptrChassisSegmentTotalOctets | read-only | mandatory | The number of octets (bytes) contained in frames received that had no errors. This includes octets in unicast, broadcast, and multicast frames. It also include… |
| 1.3.6.1.4.1.343.2.2.1.15.1.5 | ColumnrptrChassisSegmentTotalErrors | read-only | mandatory | The total number of errors detected. Total errors include FCS errors, alignment errors, frame too long, short events, late events, very long event, and rate mi… |
| 1.3.6.1.4.1.343.2.2.1.15.1.6 | ColumnrptrChassisSegmentFCSErrors | read-only | mandatory | The number of frames detected that are free of partial octets and do not pass the FCS check. Usually caused by adapter underrun (when the adapter can't get eno… |
| 1.3.6.1.4.1.343.2.2.1.15.1.7 | ColumnrptrChassisSegmentAlignmentErrors | read-only | mandatory | The number of frames detected that contain partial octets and do not pass the FCS check. |
| 1.3.6.1.4.1.343.2.2.1.15.1.8 | ColumnrptrChassisSegmentFrameTooLongs | read-only | mandatory | The number of frames detected that exceed the maximum permitted frame size. |
| 1.3.6.1.4.1.343.2.2.1.15.1.9 | ColumnrptrChassisSegmentShortEvents | read-only | mandatory | The number of fragments detected with ActivityDuration less than ShortEventMaxTime (greater than 74 bit times and less than 82 bit times). Usually indicates a … |
| 1.3.6.1.4.1.343.2.2.1.15.1.10 | ColumnrptrChassisSegmentRunts | read-only | mandatory | The number of frames detected that are less than the minimum permitted frame size of 64 octets but have a good FCS. Runts usually indicate collision fragments,… |
| 1.3.6.1.4.1.343.2.2.1.15.1.11 | ColumnrptrChassisSegmentCollisions | read-only | mandatory | Sum of all collisions for all ports in this repeater module. |
| 1.3.6.1.4.1.343.2.2.1.15.1.12 | ColumnrptrChassisSegmentLateEvents | read-only | mandatory | The number of collisions detected after the allowable detection period. Usually indicates a network topology problem, such as daisy-chaining class I 100Mbps hu… |
| 1.3.6.1.4.1.343.2.2.1.15.1.13 | ColumnrptrChassisSegmentVeryLongEvents | read-only | mandatory | The number of times MAU jabber lockup protection (MJLP) was detected due to transmission of data that exceeded 5 msec in duration (octet count greater than max… |
| 1.3.6.1.4.1.343.2.2.1.15.1.14 | ColumnrptrChassisSegmentDataRateMismatches | read-only | mandatory | A count of the occurrences of out-of-specification bit rates. This indicates the number of times the FIFO buffer overruns or underruns due to transmission rate… |
| 1.3.6.1.4.1.343.2.2.1.15.1.15 | ColumnrptrChassisSegmentAutoPartitions | read-only | mandatory | The number of times this port was automatically partitioned. This condition occurs when too many consecutive collisions are detected on the port. These collisi… |
| 1.3.6.1.4.1.343.2.2.1.15.1.16 | ColumnrptrChassisSegmentSymbolErrors | read-only | mandatory | This counter is incremented by one when a valid length packet was received at the port and there was at least one occurrence of an invalid data symbol. This ca… |
| 1.3.6.1.4.1.343.2.2.1.16 | TabletBrdgAdminTable | not-accessible | mandatory | Embedded transparent bridge administration. |
| 1.3.6.1.4.1.343.2.2.1.16.1 | RowtBrdgAdminEntry | not-accessible | mandatory | A table entry, containing administration information for a single embedded transparent bridge span. |
| 1.3.6.1.4.1.343.2.2.1.16.1.1 | ColumntBrdgAdminSpanIndex | read-only | mandatory | Embedded transparent bridge span number. A bridge span consists of one or more embedded transparent bridges forwarding packets between two segments. |
| 1.3.6.1.4.1.343.2.2.1.16.1.2 | ColumntBrdgAdminState | read-write | mandatory | The state of the embedded transparent bridging span. enable - Allows packets to be forwarded by embedded bridging to the peer segment. disable - Prevents packe… |
| 1.3.6.1.4.1.343.2.2.1.16.1.3 | ColumntBrdgReset | read-write | mandatory | 'reset' resets all enabled transparent bridges in the span. 'resetCounters' clears all transparent bridge statistics. |
| 1.3.6.1.4.1.343.2.2.1.16.1.4 | ColumntBrdgThrshld | read-write | mandatory | If the number of times the transparent bridge indicates buffer full exceeds this value, a trap is generated. Use 0 to disable. This trap is based on the number… |
| 1.3.6.1.4.1.343.2.2.1.16.1.5 | ColumntBrdgPeriod | read-write | mandatory | Time period (in minutes) that the transparent bridge buffer full count must exceed the trap threshold value in order to generate a trap. |
| 1.3.6.1.4.1.343.2.2.1.16.1.6 | ColumntBrdgLockout | read-write | mandatory | Prevents embedded transparent bridging from being enabled or disabled via a button on the front of a hub or by the local management console interface. |
| 1.3.6.1.4.1.343.2.2.1.16.1.7 | ColumntBrdgHubId | read-only | mandatory | chassisConfigTableIndex of the chassis containing the primary internal bridge for the span. All internal bridge statistics are reported as ports 101 and 102 wi… |
| 1.3.6.1.4.1.343.2.2.1.16.1.8 | ColumntBrdgSegments | read-only | mandatory | Embedded transparent bridge span segments. This is a list of segments (1 per byte) in this bridge span. |
| 1.3.6.1.4.1.343.2.2.1.17 | TabletBrdgStatsTable | not-accessible | mandatory | Embedded transparent bridge statistics. |
| 1.3.6.1.4.1.343.2.2.1.17.1 | RowtBrdgStatsEntry | not-accessible | mandatory | A table entry, containing statistics for a single embedded transparent bridge span domain. |
| 1.3.6.1.4.1.343.2.2.1.17.1.1 | ColumntBrdgStatsSpan | read-only | mandatory | Embedded transparent bridge span number. A bridge span consists of one or more embedded transparent bridges forwarding packets between two segments. |
| 1.3.6.1.4.1.343.2.2.1.17.1.2 | ColumntBrdgStatsSegment | read-only | mandatory | Embedded transparent bridge statistics segment. This index specifies which segment is associated with the transparent bridge statistics. |
| 1.3.6.1.4.1.343.2.2.1.17.1.3 | ColumntBrdgUtilIn | read-only | mandatory | The percentage of this segment's traffic that was bridged from the peer segment during the previous second. |
| 1.3.6.1.4.1.343.2.2.1.17.1.4 | ColumntBrdgUtilOut | read-only | mandatory | The percentage of this segment's traffic which was bridged to the peer segment during the previous second. |
| 1.3.6.1.4.1.343.2.2.1.17.1.5 | ColumntBrdgBufferFullCount | read-only | mandatory | The number of times internal buffer capacity was exceeded while bridging frames out of this segment. |
| 1.3.6.1.4.1.343.2.2.1.18 | NodestackConfigExtensions | |||
| 1.3.6.1.4.1.343.2.2.1.18.1 | ScalarstackClearPortSecurity | write-only | mandatory | Clears all active and persistent port security settings. |
| 1.3.6.1.4.1.343.2.2.1.19 | Nodeexpress-snmp-agents | |||
| 1.3.6.1.4.1.343.2.2.1.19.1 | Nodee300agentConfiguration | |||
| 1.3.6.1.4.1.343.2.2.1.19.1.1 | Scalare300agentVendorName | read-only | mandatory | Displays the SNMP agent's manufacturer name. |
| 1.3.6.1.4.1.343.2.2.1.19.1.2 | Scalare300agentProductName | read-only | mandatory | Displays the product name that contains the SNMP agent. |
| 1.3.6.1.4.1.343.2.2.1.19.1.3 | Scalare300agentChassisIndex | read-only | mandatory | Displays which chassis contains the SNMP agent's module. |
| 1.3.6.1.4.1.343.2.2.1.19.1.4 | Scalare300agentModuleIndex | read-only | mandatory | Displays which module in the chassis is the SNMP agent's module. The chassis number is in the object agentChassisIndex. |
| 1.3.6.1.4.1.343.2.2.1.19.1.5 | Scalare300mibversion | read-only | mandatory | Displays the version of the MIB supported by the SNMP agent. |
| 1.3.6.1.4.1.343.2.2.1.19.1.6 | Scalare300resetAgent | read-write | mandatory | Performs a cold reset of the SNMP agent. If a new IP configuration was set, it will be used after the reset. |
| 1.3.6.1.4.1.343.2.2.1.19.1.7 | Scalare300agentRole | read-only | mandatory | The current role of this agent within this hub stack. |
| 1.3.6.1.4.1.343.2.2.1.19.1.8 | Scalare300agentIpBootServerAddr | read-write | mandatory | The IP Address of Boot Server. |
| 1.3.6.1.4.1.343.2.2.1.19.1.9 | Scalare300agentIpUnauthAddr | read-only | mandatory | The IP address of an unauthorized SNMP packet. |
| 1.3.6.1.4.1.343.2.2.1.19.1.10 | Scalare300agentIpUnauthComm | read-only | mandatory | The community string of an unauthorized SNMP packet. |
| 1.3.6.1.4.1.343.2.2.1.19.1.11 | Scalare300agentIpLastBootServerAddr | read-only | mandatory | The last IP address used as Boot server IP address. |
| 1.3.6.1.4.1.343.2.2.1.19.1.12 | Scalare300agentIpLastIpAddr | read-only | mandatory | The last IP address used as the agent system IP address. |
| 1.3.6.1.4.1.343.2.2.1.19.2 | Nodee300ipConfiguration | |||
| 1.3.6.1.4.1.343.2.2.1.19.2.1 | Scalare300ipAddressMethodInUse | read-only | mandatory | Displays how the IP address in use was determined. For example, fixed means the IP address was assigned by the user and stored within the Management Module. BO… |
| 1.3.6.1.4.1.343.2.2.1.19.2.2 | Scalare300ipAddressInUse | read-only | mandatory | Displays the IP address currently in use. |
| 1.3.6.1.4.1.343.2.2.1.19.2.3 | Scalare300gatewayorRouterAddrInUse | read-only | mandatory | Displays the default gateway address currently in use. This is the device that routes to a different network. Usually a router or a routing server. |
| 1.3.6.1.4.1.343.2.2.1.19.2.4 | Scalare300networkMaskInUse | read-only | mandatory | Displays the network (subnet) mask currently in use. This must match the masks of other devices on the same network. |
| 1.3.6.1.4.1.343.2.2.1.19.2.5 | Scalare300broadcastAddressInUse | read-only | mandatory | Displays the broadcast address currently in use. |
| 1.3.6.1.4.1.343.2.2.1.19.2.6 | Scalare300ipAddressMethodNextReset | read-write | mandatory | Displays how the IP address will be determined after the SNMP agent is reset. For example, fixed means the IP address will be determined locally. BOOTP means t… |
| 1.3.6.1.4.1.343.2.2.1.19.2.7 | Scalare300ipAddressNextReset | read-write | mandatory | Displays the IP address the SNMP agent will use the next time it is reset. |
| 1.3.6.1.4.1.343.2.2.1.19.2.8 | Scalare300gatewayorRouterAddrNextReset | read-write | mandatory | Displays the default gateway the SNMP agent will use the next time it is reset. |
| 1.3.6.1.4.1.343.2.2.1.19.2.9 | Scalare300networkMaskNextReset | read-write | mandatory | Displays the netmask (subnet mask) the SNMP agent will use the next time it is reset. |
| 1.3.6.1.4.1.343.2.2.1.19.3 | Nodee300snmpConfiguration | |||
| 1.3.6.1.4.1.343.2.2.1.19.3.1 | Scalare300snmpReadCommunityString | write-only | mandatory | Sets the password for reads from the SNMP agent's MIB. |
| 1.3.6.1.4.1.343.2.2.1.19.3.2 | Scalare300snmpWriteCommunityString | write-only | mandatory | Sets the password for writes to the SNMP agent's MIB. |
| 1.3.6.1.4.1.343.2.2.1.19.3.3 | Scalare300snmpTrapReceiverMAX | read-only | mandatory | Displays the maximum number of trap receiving stations. |
| 1.3.6.1.4.1.343.2.2.1.19.3.4 | Scalare300snmpTrapReceiverNumber | read-only | mandatory | Displays the current number of trap receiving stations. |
| 1.3.6.1.4.1.343.2.2.1.19.3.5 | Tablee300snmpTrapAddressTable | not-accessible | mandatory | Contains information on individual trap receiving stations. |
| 1.3.6.1.4.1.343.2.2.1.19.3.5.1 | Rowe300snmpTrapAddressEntry | not-accessible | mandatory | An entry in the table, containing information on an individual trap receiving station. |
| 1.3.6.1.4.1.343.2.2.1.19.3.5.1.1 | Columne300trapAddrIndex | read-only | mandatory | Displays the index number of the trap receiving station. |
| 1.3.6.1.4.1.343.2.2.1.19.3.5.1.2 | Columne300trapIPAddr | read-write | mandatory | Sets the IP address for a trap receiving station. |
| 1.3.6.1.4.1.343.2.2.1.19.3.5.1.3 | Columne300trapCommunityString | read-write | mandatory | Sets the password for sending traps from the SNMP agent to the SNMP application on the trap receiving station. |
| 1.3.6.1.4.1.343.2.2.1.19.3.5.1.4 | Columne300trapStatus | read-write | mandatory | Displays whether traps should be sent to this station (active) or whether traps should not be sent to this station (ignore). |
| 1.3.6.1.4.1.343.2.2.1.19.4 | Nodee300agentExtConfiguration | |||
| 1.3.6.1.4.1.343.2.2.1.19.4.1 | Scalare300agentSwUpdateMode | read-write | mandatory | The download media used by the system to download the runtime firmware. |
| 1.3.6.1.4.1.343.2.2.1.19.4.2 | Scalare300agentConfigUpdateCtrl | read-write | mandatory | Current status of configuration file download control. The setting is effective the next time you reset or power on the hub. |
| 1.3.6.1.4.1.343.2.2.1.19.4.3 | Scalare300agentConfigFilename | read-write | mandatory | The name of the configuration file to be downloaded from the BootP or TFTP server when agentConfigUpdateCtrl is enabled. |
| 1.3.6.1.4.1.343.2.2.1.19.4.4 | Scalare300agentImageUpdateCtrl | read-write | mandatory | Current status of firmware image download control. The setting is effective the next time you reset or power on the hub. |
| 1.3.6.1.4.1.343.2.2.1.19.4.5 | Scalare300agentImageFilename | read-write | mandatory | The name of the image file to be downloaded from the TFTP server when agentImageUpdateCtrl is enabled. |
| 1.3.6.1.4.1.343.2.2.1.19.4.6 | Scalare300agentRs232PortConfig | read-write | mandatory | The current setting of RS-232C port. The RS-232C port can be configured as the console port or used for out-of-band connection. |
| 1.3.6.1.4.1.343.2.2.1.19.4.7 | Scalare300agentOutOfBandBaudRateConfig | read-write | mandatory | The baud rate setting for out of band connection. The baud rate for the console interface is always 9600. |
| 1.3.6.1.4.1.343.2.2.1.19.5 | Nodee300slipConfiguration | |||
| 1.3.6.1.4.1.343.2.2.1.19.5.1 | Scalare300slipAddressInUse | read-only | mandatory | Displays the IP address currently in use. |
| 1.3.6.1.4.1.343.2.2.1.19.5.2 | Scalare300slipGatewayorRouterAddrInUse | read-only | mandatory | Displays the default gateway address currently in use. This is the device that routes to a different network. Usually a router or a routing server. |
| 1.3.6.1.4.1.343.2.2.1.19.5.3 | Scalare300slipNetworkMaskInUse | read-only | mandatory | Displays the network (subnet) mask currently in use. This must match the masks of other devices on the same network. |
| 1.3.6.1.4.1.343.2.2.1.19.5.4 | Scalare300slipBroadcastAddressInUse | read-only | mandatory | Displays the broadcast address currently in use. |
| 1.3.6.1.4.1.343.2.2.1.19.5.5 | Scalare300slipAddressNextReset | read-write | mandatory | Displays the IP address the SNMP agent will use the next time it is reset. |
| 1.3.6.1.4.1.343.2.2.1.19.5.6 | Scalare300slipGatewayorRouterAddrNextReset | read-write | mandatory | Displays the default gateway the SNMP agent will use the next time it is reset. |
| 1.3.6.1.4.1.343.2.2.1.19.5.7 | Scalare300slipNetworkMaskNextReset | read-write | mandatory | Displays the netmask (subnet mask) the SNMP agent will use the next time it is reset. |
| 1.3.6.1.4.1.343.2.2.1.19.6 | Tablee300mgmtBasicInfoTable | not-accessible | mandatory | A list of SNMP agent basic information. |
| 1.3.6.1.4.1.343.2.2.1.19.6.1 | Rowe300mgmtBasicInfoEntry | not-accessible | mandatory | A table entry, containing SNMP agent basic information. |
| 1.3.6.1.4.1.343.2.2.1.19.6.1.1 | Columne300mgmtChassisIndex | read-only | mandatory | Chassis number in the stack which SNMP agent located. |
| 1.3.6.1.4.1.343.2.2.1.19.6.1.2 | Columne300mgmtIPAddress | read-only | mandatory | IP address of the SNMP agent. |
| 1.3.6.1.4.1.343.2.2.1.19.6.1.3 | Columne300mgmtPhysicalAddress | read-only | mandatory | Physical address of the SNMP agent. |
| 1.3.6.1.4.1.343.2.2.1.19.6.1.4 | Columne300mgmtRole | read-only | mandatory | The current role of the SNMP agent within this hub stack. |