INTEL-S500-MIB
213 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.343.6.10 | Nodes500 | |||
| 1.3.6.1.4.1.343.6.10.1 | Nodemodule | |||
| 1.3.6.1.4.1.343.6.10.1 | Nodes500PermVioEvent | This trap is sent when there has been a permanent entry violation. A MAC address has been detected at a port, other than the port where it has been configured … | ||
| 1.3.6.1.4.1.343.6.10.1.1 | ScalardefaultSwitchMode | read-write | mandatory | Default switch mode. This is used by the object portSwitchMode when it's value is default(1) |
| 1.3.6.1.4.1.343.6.10.1.2 | ScalardefaultFlowControlMode | read-write | mandatory | Default Flow Control mode. This is used by the object portConfFlowControl when it's value is default(1) |
| 1.3.6.1.4.1.343.6.10.1.3 | ScalarsmuMaster | read-only | mandatory | OBSOLETE |
| 1.3.6.1.4.1.343.6.10.1.4 | ScalarlocalManagementTimeout | read-write | mandatory | The time (in minutes) that has elapsed before a local management session (telnet or serial) closes when it has not been used. The value '0' means no timeout. |
| 1.3.6.1.4.1.343.6.10.1.5 | ScalartemperatureLevel | read-only | mandatory | temperatureLevel values: normal(1) : Temperature normal high(2) : Temperature high. Check air circulation critical(3): Temperature critical. Shut down in 30 se… |
| 1.3.6.1.4.1.343.6.10.1.6 | ScalarredundantPowerSupplyStatus | read-only | mandatory | Status for redundant power supply: notPresent(1): RPS not connected or failed. (It may be present but not plugged in or damaged etc.) present(2): RPS not activ… |
| 1.3.6.1.4.1.343.6.10.1.7 | ScalarportMirroring | read-write | mandatory | enable(1): Enabling of port mirroring. This is only possible if RMON is disabled. disable(2): Disabling of port mirroring. RMON can only be enabled if port mir… |
| 1.3.6.1.4.1.343.6.10.1.8 | ScalardisableRmon | write-only | mandatory | destroyAll(1): Disable RMON and destroy all probes. This is necessary for enabling port mirroring |
| 1.3.6.1.4.1.343.6.10.1.9 | ScalarisRmonActive | read-only | mandatory | enabled(1): RMON is enabled disabled(2): RMON is disabled |
| 1.3.6.1.4.1.343.6.10.1.10 | ScalarswitchTotalTraffic | read-only | mandatory | Total switch traffic measured in octets |
| 1.3.6.1.4.1.343.6.10.1.11 | ScalarbufferPoolUsed | read-only | mandatory | Total switch buffer pool usage. (percentage between 0 and 100) |
| 1.3.6.1.4.1.343.6.10.1.12 | ScalarfeaturesBitFlag | read-only | mandatory | Bit field index from bit 1 to 32. If an bit is set, the switch supports the related feature. BIT 1: Distributed VLAN BIT 2: Layer 3 switching BIT 3: Diagnostic… |
| 1.3.6.1.4.1.343.6.10.1.13 | ScalarswitchBw | read-only | mandatory | Max switch BW. (Mbits per second) |
| 1.3.6.1.4.1.343.6.10.1.14 | ScalarownMatrixAttachmentPort | read-only | mandatory | Returns the port number of the Matrix port the switch is attached to. NB: will return 50 for a switch not connected to a Matrix Module |
| 1.3.6.1.4.1.343.6.10.1.15 | ScalarstackCrc | read-only | mandatory | checksum for stack specific parameters If a parameter is unavailable 0 is returned |
| 1.3.6.1.4.1.343.6.10.2 | Nodeports | |||
| 1.3.6.1.4.1.343.6.10.2 | Nodes500AdaptiveForwEvent | This trap is sent when a port automatically is changing forwarding mode. This will only happen when the port has been configured to Adaptive mode. The syntax i… | ||
| 1.3.6.1.4.1.343.6.10.2.1 | ScalarportSnmpPort | read-only | mandatory | Returns the port which this SNMP request went through. This gives the port on which the SNMP management system is connected. |
| 1.3.6.1.4.1.343.6.10.2.2 | ScalarportLastChange | read-only | mandatory | The value of sysUpTime after any interface has changed state |
| 1.3.6.1.4.1.343.6.10.2.3 | TableportInfoTable | not-accessible | mandatory | Port information table which includes all ports. |
| 1.3.6.1.4.1.343.6.10.2.3.1 | RowportInfoEntry | not-accessible | mandatory | Contains the type of interface . |
| 1.3.6.1.4.1.343.6.10.2.3.1.1 | ColumnportInfoChassisIndex | read-only | mandatory | Chassis index |
| 1.3.6.1.4.1.343.6.10.2.3.1.2 | ColumnportInfoModuleIndex | read-only | mandatory | Module index |
| 1.3.6.1.4.1.343.6.10.2.3.1.3 | ColumnportInfoIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.343.6.10.2.3.1.4 | ColumnportInfoType | read-only | mandatory | The type of Physical interface at the port. |
| 1.3.6.1.4.1.343.6.10.2.4 | TableportConfTable | not-accessible | mandatory | Port configuration and status table. |
| 1.3.6.1.4.1.343.6.10.2.4.1 | RowportConfEntry | not-accessible | mandatory | An entry containing the objects for configuration and status of a port. |
| 1.3.6.1.4.1.343.6.10.2.4.1.1 | ColumnportConfChassisIndex | read-only | mandatory | Chassis index |
| 1.3.6.1.4.1.343.6.10.2.4.1.2 | ColumnportConfModuleIndex | read-only | mandatory | Module index |
| 1.3.6.1.4.1.343.6.10.2.4.1.3 | ColumnportConfIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.343.6.10.2.4.1.4 | ColumnportConfDescr | read-write | mandatory | User configurable description of the port. |
| 1.3.6.1.4.1.343.6.10.2.4.1.5 | ColumnportConfLocation | read-write | mandatory | User configurable location of the port. |
| 1.3.6.1.4.1.343.6.10.2.4.1.6 | ColumnportConfConfigSwitchMode | read-write | mandatory | Port Switch mode. If set to default(1) the value from defaultSwitchMode is used. |
| 1.3.6.1.4.1.343.6.10.2.4.1.7 | ColumnportConfFlowControl | read-write | mandatory | Port Flow Control mode. If set to default(1) the value from defaultFlowControlMode is used. |
| 1.3.6.1.4.1.343.6.10.2.4.1.8 | ColumnportConfSpeedSupported | read-only | mandatory | The possible speeds of a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.9 | ColumnportConfDuplexSupported | read-only | mandatory | The possible duplex modes of a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.10 | ColumnportConfConfigSpeed | read-write | mandatory | The configured speed for a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.11 | ColumnportConfConfigDuplex | read-write | mandatory | The configured duplex mode for a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.12 | ColumnportConfConfigAutoNeg | read-write | mandatory | The configured auto-negotiation for a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.13 | ColumnportConfSpeed | read-only | mandatory | The current speed for a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.14 | ColumnportConfDuplex | read-only | mandatory | The current duplex mode for a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.15 | ColumnportConfAutoNeg | read-only | mandatory | The currect auto-negotiation for a port |
| 1.3.6.1.4.1.343.6.10.2.4.1.16 | ColumnportConfSwitchMode | read-only | mandatory | Current forwarding mode of the port. |
| 1.3.6.1.4.1.343.6.10.2.4.1.17 | ColumnportConfTrunkSupported | read-only | mandatory | The types of port trunking available for the actual port. A trunk consists of a number ports sitting next to each other. The first port is selected as master f… |
| 1.3.6.1.4.1.343.6.10.2.4.1.18 | ColumnportConfTrunkConfig | read-write | mandatory | The size of the actual trunk. 0 means trunkWidthTwo(1): This port is member of a 2 port trunk. trunkWidthFour(2):This port is member of a 4 port trunk. disable… |
| 1.3.6.1.4.1.343.6.10.2.4.1.19 | ColumnportConfTrunkName | read-write | mandatory | Trunk name |
| 1.3.6.1.4.1.343.6.10.2.4.1.20 | ColumnportConfMirrorSupported | read-only | mandatory | Which mode of port mirroring does the port support. mirrorSourceOnly(1): Port can only be used as source for mirroring mirrorDestinationOnly(2): Port can only … |
| 1.3.6.1.4.1.343.6.10.2.4.1.21 | ColumnportConfMirrorConfig | read-write | mandatory | The configured port mirroring for the actual port. mirrorSource(1): Port is source for mirroring mirrorDestination(2): Port is destination for mirroring disabl… |
| 1.3.6.1.4.1.343.6.10.2.4.1.22 | ColumnportConfVlanSupported | read-only | mandatory | Describes if the port can be used as a port rule in the VLAN configuration. enabled(1): Port can be used in port VLANs notAvailable(99): Port can not be used i… |
| 1.3.6.1.4.1.343.6.10.2.5 | ScalarportAllSpanningTreeMode | read-write | mandatory | Enable or Disable Spanning Tree Protocol for all ports on switch. SET is only allowed with value allEnabled(1) or allDisabled(2). |
| 1.3.6.1.4.1.343.6.10.3 | Nodes500TemperatureEvent | This trap indicates that the temparature of the chassis has changed | ||
| 1.3.6.1.4.1.343.6.10.3 | Nodestatistic | |||
| 1.3.6.1.4.1.343.6.10.3.1 | TabletxStatTable | not-accessible | mandatory | Transmit statistics table. |
| 1.3.6.1.4.1.343.6.10.3.1.1 | RowtxStatEntry | not-accessible | mandatory | An entry containing objects for transmit statistics. |
| 1.3.6.1.4.1.343.6.10.3.1.1.1 | ColumntxStatIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.343.6.10.3.1.1.2 | ColumntxUCPkts64Octets | read-only | mandatory | 64 byte unicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.3 | ColumntxUCPkts65To127Octets | read-only | mandatory | 65 to 127 byte unicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.4 | ColumntxUCPkts128To255Octets | read-only | mandatory | 128 to 255 byte unicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.5 | ColumntxUCPkts256To511Octets | read-only | mandatory | 256 to 511 byte unicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.6 | ColumntxUCPkts512To1023Octets | read-only | mandatory | 512 to 1023 byte unicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.7 | ColumntxUCPkts1024To1518Octets | read-only | mandatory | 1024 to 1518 byte unicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.8 | ColumntxMCPkts64Octets | read-only | mandatory | 64 byte multicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.9 | ColumntxMCPkts65To127Octets | read-only | mandatory | 65 to 127 byte multicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.10 | ColumntxMCPkts128To255Octets | read-only | mandatory | 128 to 255 byte multicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.11 | ColumntxMCPkts256To511Octets | read-only | mandatory | 256 to 511 byte multicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.12 | ColumntxMCPkts512To1023Octets | read-only | mandatory | 512 to 1023 byte multicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.13 | ColumntxMCPkts1024To1518Octets | read-only | mandatory | 1024 to 1518 byte multicast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.14 | ColumntxBCPkts64Octets | read-only | mandatory | 64 byte broadcast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.15 | ColumntxBCPkts65To127Octets | read-only | mandatory | 65 to 127 byte broadcast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.16 | ColumntxBCPkts128To255Octets | read-only | mandatory | 128 to 255 byte broadcast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.17 | ColumntxBCPkts256To511Octets | read-only | mandatory | 256 to 511 byte broadcast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.18 | ColumntxBCPkts512To1023Octets | read-only | mandatory | 512 to 1023 byte broadcast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.19 | ColumntxBCPkts1024To1518Octets | read-only | mandatory | 1024 to 1518 byte broadcast packets transmitted |
| 1.3.6.1.4.1.343.6.10.3.1.1.20 | ColumntxOctetsIllegalAddrType | read-only | mandatory | |
| 1.3.6.1.4.1.343.6.10.3.1.1.21 | Columntx1ArbitFrameDelay | read-only | mandatory | Tx packets delayed less than 1 slot time (due to NIMBUS overload). |
| 1.3.6.1.4.1.343.6.10.3.1.1.22 | Columntx2ArbitFrameDelay | read-only | mandatory | Tx packets delayed between 1 and 2 slot times (due to NIMBUS overload) |
| 1.3.6.1.4.1.343.6.10.3.1.1.23 | Columntx3ArbitFrameDelay | read-only | mandatory | Tx packets delayed between 2 and 4 slot times (due to NIMBUS overload) |
| 1.3.6.1.4.1.343.6.10.3.1.1.24 | Columntx4ArbitFrameDelay | read-only | mandatory | Tx packets delayed between 4 and 8 slot times (due to NIMBUS overload) |
| 1.3.6.1.4.1.343.6.10.3.1.1.25 | Columntx5ArbitFrameDelay | read-only | mandatory | Tx packets delayed between 8 and 16 slot times (due to NIMBUS overload) |
| 1.3.6.1.4.1.343.6.10.3.1.1.26 | Columntx6ArbitFrameDelay | read-only | mandatory | Tx packets delayed between 16 and 32 slot times (due to NIMBUS overload) |
| 1.3.6.1.4.1.343.6.10.3.1.1.27 | Columntx7ArbitFrameDelay | read-only | mandatory | Tx packets delayed more than 32 slot times (due to NIMBUS overload) |
| 1.3.6.1.4.1.343.6.10.3.1.1.28 | ColumntxDeferreds | read-only | mandatory | Half duplex: Tx packet delayed, due to receiving a packet. Full duplex: Tx packet delayed, due to receiving of a MAC pause control frame. |
| 1.3.6.1.4.1.343.6.10.3.1.1.29 | ColumntxOctetsHis | read-only | mandatory | Upper part of a 64 bit octet transmitted counter |
| 1.3.6.1.4.1.343.6.10.3.1.1.30 | ColumntxOctetsLos | read-only | mandatory | Lower part of a 64 bit octet transmitted counter |
| 1.3.6.1.4.1.343.6.10.3.1.1.31 | ColumntxOctetsOutOfRange | read-only | mandatory | Internal error |
| 1.3.6.1.4.1.343.6.10.3.1.1.32 | ColumntxExcessiveDeferralsErrors | read-only | mandatory | Maximum deferral should be the duration of a maximum length packet, if no errors on the net. Excessive deferral is indicated if deferral duration is more than … |
| 1.3.6.1.4.1.343.6.10.3.1.1.34 | ColumntxNiaUnderRunAborts | read-only | mandatory | Internal discard |
| 1.3.6.1.4.1.343.6.10.3.1.1.35 | ColumntxExcessiveLengthDrops | read-only | mandatory | Tx packets discarded due to too long packets (Only possible if receiving too long packets are allowed) |
| 1.3.6.1.4.1.343.6.10.3.1.1.36 | ColumntxLinkDownEvents | read-only | mandatory | No link pulses are received. Usually this means that the cable is removed. |
| 1.3.6.1.4.1.343.6.10.3.1.1.37 | ColumntxAllCounterPackets | read-only | mandatory | A collection of all counters for byte and packet counters. This object is needed to optimize SNMP traffic. The counters in this string are: txStatIndex INTEGER… |
| 1.3.6.1.4.1.343.6.10.3.1.1.38 | ColumntxAllCounterOthers | read-only | mandatory | A collection of all counters for byte and packet counters. This object is needed to optimize SNMP traffic. The counters in this string are: txStatIndex INTEGER… |
| 1.3.6.1.4.1.343.6.10.3.2 | TablerxStatTable | not-accessible | mandatory | Receive statistics table. |
| 1.3.6.1.4.1.343.6.10.3.2.1 | RowrxStatEntry | not-accessible | mandatory | An entry containing objects for receive statistics. |
| 1.3.6.1.4.1.343.6.10.3.2.1.1 | ColumnrxStatIndex | read-only | mandatory | An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the s… |
| 1.3.6.1.4.1.343.6.10.3.2.1.2 | ColumnrxUCPkts64OctetsLocals | read-only | mandatory | 64 byte unicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.3 | ColumnrxUCPkts64OctetsForwardeds | read-only | mandatory | 64 byte unicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.4 | ColumnrxUCPkts65To127OctetsLocals | read-only | mandatory | 65 to 127 byte unicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.5 | ColumnrxUCPkts65To127OctetsForwardeds | read-only | mandatory | 65 to 127 byte unicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.6 | ColumnrxUCPkts128To255OctetsLocals | read-only | mandatory | 128 to 255 byte unicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.7 | ColumnrxUCPkts128To255OctetsForwardeds | read-only | mandatory | 128 to 255 byte unicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.8 | ColumnrxUCPkts256To511OctetsLocals | read-only | mandatory | 256 to 511 byte unicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.9 | ColumnrxUCPkts256To511OctetsForwardeds | read-only | mandatory | 255 to 511 byte unicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.10 | ColumnrxUCPkts512To1023OctetsLocals | read-only | mandatory | 512 to 1023 byte unicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.11 | ColumnrxUCPkts512To1023OctetsForwardeds | read-only | mandatory | 512 to 1023 byte unicast packets received which has been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.12 | ColumnrxUCPkts1024To1518OctetsLocals | read-only | mandatory | 1024 to 1518 byte unicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.13 | ColumnrxUCPkts1024To1518OctetsForwardeds | read-only | mandatory | 1024 to 1518 byte unicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.14 | ColumnrxShortErrors | read-only | mandatory | Receive fragments shorter than the minimum ordinary collision fragment. |
| 1.3.6.1.4.1.343.6.10.3.2.1.15 | ColumnrxRuntErrors | read-only | mandatory | Ordinary collision fragments received. |
| 1.3.6.1.4.1.343.6.10.3.2.1.16 | ColumnrxDataRateMMErrors | read-only | mandatory | A data rate miss-match error occurs if the data rate deviation is larger than allowed. This should only occur if problems with the TX oscillator in the adapter… |
| 1.3.6.1.4.1.343.6.10.3.2.1.17 | ColumnrxMCPkts64OctetsLocals | read-only | mandatory | 64 byte multicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.18 | ColumnrxMCPkts64OctetsForwardeds | read-only | mandatory | 64 byte multicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.19 | ColumnrxMCPkts65To127OctetsLocals | read-only | mandatory | 65 to 127 byte multicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.20 | ColumnrxMCPkts65To127OctetsForwardeds | read-only | mandatory | 65 to 127 byte multicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.21 | ColumnrxMCPkts128To255OctetsLocals | read-only | mandatory | 128 to 255 byte multicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.22 | ColumnrxMCPkts128To255OctetsForwardeds | read-only | mandatory | 128 to 255 byte multicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.23 | ColumnrxMCPkts256To511OctetsLocals | read-only | mandatory | 256 to 511 byte multicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.24 | ColumnrxMCPkts256To511OctetsForwardeds | read-only | mandatory | 256 to 511 byte multicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.25 | ColumnrxMCPkts512To1023OctetsLocals | read-only | mandatory | 512 to 1023 byte multicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.26 | ColumnrxMCPkts512To1023OctetsForwardeds | read-only | mandatory | 512 to 1023 byte multicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.27 | ColumnrxMCPkts1024To1518OctetsLocals | read-only | mandatory | 1024 to 1518 byte multicast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.28 | ColumnrxMCPkts1024To1518OctetsForwardeds | read-only | mandatory | 1024 to 1518 byte multicast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.29 | ColumnrxOctetsLocalHis | read-only | mandatory | Upper part of a 64 bit octet received counter which has not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.30 | ColumnrxOctetsLocalLos | read-only | mandatory | Lower part of a 64 bit octet received counter which has not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.31 | ColumnrxOctetsForwardedHis | read-only | mandatory | Upper part of a 64 bit octet received counter which has been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.32 | ColumnrxOctetsForwardedLos | read-only | mandatory | Lower part of a 64 bit octet received counter which has been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.33 | ColumnrxBCPkts64OctetsLocals | read-only | mandatory | 64 byte broadcast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.34 | ColumnrxBCPkts64OctetsForwardeds | read-only | mandatory | 64 byte broadcast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.35 | ColumnrxBCPkts65To127OctetsLocals | read-only | mandatory | 65 to 127 byte broadcast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.36 | ColumnrxBCPkts65To127OctetsForwardeds | read-only | mandatory | 65 to 127 byte broadcast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.37 | ColumnrxBCPkts128To255OctetsLocals | read-only | mandatory | 128 to 255 byte broadcast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.38 | ColumnrxBCPkts128To255OctetsForwardeds | read-only | mandatory | 128 to 255 byte broadcast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.39 | ColumnrxBCPkts256To511OctetsLocals | read-only | mandatory | 256 to 511 byte broadcast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.40 | ColumnrxBCPkts256To511OctetsForwardeds | read-only | mandatory | 256 to 511 byte broadcast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.41 | ColumnrxBCPkts512To1023OctetsLocals | read-only | mandatory | 512 to 1023 byte broadcast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.42 | ColumnrxBCPkts512To1023OctetsForwardeds | read-only | mandatory | 512 to 1023 byte broadcast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.43 | ColumnrxBCPkts1024To1518OctetsLocals | read-only | mandatory | 1024 to 1518 byte broadcast packets received which have not been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.44 | ColumnrxBCPkts1024To1518OctetsForwardeds | read-only | mandatory | 1024 to 1518 byte broadcast packets received which have been forwarded |
| 1.3.6.1.4.1.343.6.10.3.2.1.45 | ColumnrxFilterMACUnexp2ndPortDrops | read-only | mandatory | MAC address has been moved from one port to another |
| 1.3.6.1.4.1.343.6.10.3.2.1.46 | ColumnrxFilterIllegalMACDrops | read-only | mandatory | Packet is dropped because the source MAC address is illegal (zero or broadcase) |
| 1.3.6.1.4.1.343.6.10.3.2.1.47 | ColumnrxFlowCtrlPram | read-only | mandatory | Half duplex: Number of Flow Control collisions generated due to PRAM limitations. Full duplex: Number of MAC pause control frames transmitted due to PRAM limit… |
| 1.3.6.1.4.1.343.6.10.3.2.1.48 | ColumnrxFlowCtrlNimbus | read-only | mandatory | Half duplex: Number of Flow Control collisions generated due to NIMBUS overload. Full duplex: Number of MAC pause control frames transmitted due to NIMBUS over… |
| 1.3.6.1.4.1.343.6.10.3.2.1.49 | ColumnrxPramOverRuns | read-only | mandatory | Rx packets discarded due to PRAM limitation |
| 1.3.6.1.4.1.343.6.10.3.2.1.50 | ColumnrxNimbusOverRuns | read-only | mandatory | Rx packets discarded due to NIMBUS limitation |
| 1.3.6.1.4.1.343.6.10.3.2.1.51 | ColumnrxVeryLongErrors | read-only | mandatory | Rx packets that are much too long (> 6000 bytes). |
| 1.3.6.1.4.1.343.6.10.3.2.1.52 | ColumnrxLongErrors | read-only | mandatory | Rx packets that are too long (> 1518 bytes) |
| 1.3.6.1.4.1.343.6.10.3.2.1.53 | ColumnrxPauseMacControlReceived | read-only | mandatory | Number of MAC pause control frames received |
| 1.3.6.1.4.1.343.6.10.3.2.1.54 | ColumnrxUnknownMacControlFrame | read-only | mandatory | Number of unsupported MAC control frames received |
| 1.3.6.1.4.1.343.6.10.3.2.1.55 | ColumnrxPiaOutOfPoolDropErrors | read-only | mandatory | |
| 1.3.6.1.4.1.343.6.10.3.2.1.56 | ColumnrxCodeViolations | read-only | mandatory | An illegal symbol received on a 100Base-X port. |
| 1.3.6.1.4.1.343.6.10.3.2.1.57 | ColumnrxJabberErrors | read-only | mandatory | Rx packets that are too long and contains CRC errors and/or dribble nibble. |
| 1.3.6.1.4.1.343.6.10.3.2.1.58 | ColumnrxNiaOverRunDropErrors | read-only | mandatory | The NIA Rx buffer goes to overrun if the nimbus is overloaded (NIA10 only). |
| 1.3.6.1.4.1.343.6.10.3.2.1.59 | ColumnrxAllCounterPackets | read-only | mandatory | A collection of all counters for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are: rxStatIndex INTEGER… |
| 1.3.6.1.4.1.343.6.10.3.2.1.60 | ColumnrxAllCounterOthers | read-only | mandatory | A collection of all counters other than for byte and packet counters. This object is needed to optimize SNMP traffic. The counters in this string are: rxStatIn… |
| 1.3.6.1.4.1.343.6.10.3.3 | ScalartotalRxTxPackets | read-only | mandatory | This object is used for LED control to display traffic. Values in the string are all packets transmitted and received at each port. The number and order of val… |
| 1.3.6.1.4.1.343.6.10.3.4 | ScalartotalCollisions | read-only | mandatory | This object is used for LED control to display collision. Values in the string are the total collisions at each port. The number and order of values equals the… |
| 1.3.6.1.4.1.343.6.10.4 | NodeadaptiveForwardMode | |||
| 1.3.6.1.4.1.343.6.10.4 | Nodes500RedundantPowerSupplyEvent | This trap indicates that the status of the redundant power supply has changed | ||
| 1.3.6.1.4.1.343.6.10.4.1 | ScalaradaptiveForwardModeSampleTime | read-write | mandatory | Specify how long (in seconds) the received packets will be monitored. The resulting forwarding mode will be based on the quality of the packets |
| 1.3.6.1.4.1.343.6.10.4.2 | ScalaradaptiveForwardModeRuntsOffset | read-write | mandatory | Specifies the minimum amount of runts during the sample time which forces the port out of cutThrough(2). The value is specified in per mill * 1000 |
| 1.3.6.1.4.1.343.6.10.4.3 | ScalaradaptiveForwardModeRuntsRange | read-write | mandatory | Specifies (together with adaptiveForwardModeRuntsOffset) the maximum amount of runts allowed during the sample time. This forces the port back to cutThrough(2)… |
| 1.3.6.1.4.1.343.6.10.4.4 | ScalaradaptiveForwardModeCrcsOffset | read-write | mandatory | Specifies the maximum amount of CRC errors during the sample time. This forces the port out of Store-and-Forward. The value is specified in per mill * 1000 |
| 1.3.6.1.4.1.343.6.10.4.5 | ScalaradaptiveForwardModeCrcsRange | read-write | mandatory | Specifies together with adaptiveForwardModeCrcsOffset the maximum amount of CRC errors during the sample time. This forces the port out of Store-and-Forward. T… |
| 1.3.6.1.4.1.343.6.10.5 | NodechipSets | |||
| 1.3.6.1.4.1.343.6.10.6 | Nodesmu | |||
| 1.3.6.1.4.1.343.6.10.6.1 | TablesmuModuleTable | not-accessible | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.1.1 | RowsmuModuleEntry | not-accessible | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.1.1.1 | ColumnsmuModuleChassisIndex | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.1.1.2 | ColumnsmuModuleIndex | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.1.1.3 | ColumnsmuModuleState | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2 | TablesmuPortTable | not-accessible | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1 | RowsmuPortEntry | not-accessible | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1.1 | ColumnsmuPortChassisIndex | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1.2 | ColumnsmuPortModuleIndex | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1.3 | ColumnsmuPortIndex | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1.4 | ColumnsmuPortAttachedNumber | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1.5 | ColumnsmuPortAttachedMac | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.6.2.1.6 | ColumnsmuPortAttachedIp | read-only | mandatory | Not implemented yet |
| 1.3.6.1.4.1.343.6.10.7 | NodepermanentEntries | |||
| 1.3.6.1.4.1.343.6.10.7.1 | TablepermanentEntriesTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.343.6.10.7.1.1 | RowpermanentEntriesEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.343.6.10.7.1.1.1 | ColumnpermanentEntriesMACAddr | read-write | mandatory | MAC address of permanent entry. |
| 1.3.6.1.4.1.343.6.10.7.1.1.2 | ColumnpermanentEntriesPortId | read-write | mandatory | Port number for permanent entry. |
| 1.3.6.1.4.1.343.6.10.7.1.1.3 | ColumnpermanentEntriesCreateObj | read-write | mandatory | Create a non-existant table entry. If the entry already exists, genError is returned. Format: PortId (INTEGER) |
| 1.3.6.1.4.1.343.6.10.7.1.1.4 | ColumnpermanentEntriesDeleteObj | read-write | mandatory | Delete an existing table entry. |
| 1.3.6.1.4.1.343.6.10.8 | Nodematrix | |||
| 1.3.6.1.4.1.343.6.10.8.1 | TablematrixModuleTable | not-accessible | mandatory | The table for general stack information |
| 1.3.6.1.4.1.343.6.10.8.1.1 | RowmatrixModuleEntry | not-accessible | mandatory | Information for a specific module slot about stackconnections, state, masterinformation |
| 1.3.6.1.4.1.343.6.10.8.1.1.1 | ColumnmatrixModuleIndex | read-only | mandatory | Slot number to retrieve information for. 1 is slot A, 2 is slot B |
| 1.3.6.1.4.1.343.6.10.8.1.1.2 | ColumnmatrixModuleState | read-only | mandatory | State of the matrix module. If notAvailable(99) no matrix module can be seen, active(1) is indicating a running module, standby(2) is indicating a module that … |
| 1.3.6.1.4.1.343.6.10.8.1.1.3 | ColumnmatrixNumberConnected | read-only | mandatory | The number of connected units to the matrix module |
| 1.3.6.1.4.1.343.6.10.8.1.1.4 | ColumnmatrixMasterPort | read-only | mandatory | 0 means no master available, otherwise an ifindex is returned (50->57) |
| 1.3.6.1.4.1.343.6.10.8.2 | TablematrixPortTable | not-accessible | mandatory | Matrix module per port overview. |
| 1.3.6.1.4.1.343.6.10.8.2.1 | RowmatrixPortEntry | not-accessible | mandatory | Per switch of information gathered from the matrix module about the connected devices |
| 1.3.6.1.4.1.343.6.10.8.2.1.1 | ColumnmatrixPortModuleIndex | read-only | mandatory | Slot number to retrieve information for. 1 is slot A, 2 is slot B |
| 1.3.6.1.4.1.343.6.10.8.2.1.2 | ColumnmatrixPortIndex | read-only | mandatory | Index for retrieving the matrix ports |
| 1.3.6.1.4.1.343.6.10.8.2.1.3 | ColumnmatrixPort | read-only | mandatory | 0 means no device is available, otherwise an ifindex is returned (50->57) |
| 1.3.6.1.4.1.343.6.10.8.2.1.4 | ColumnmatrixPortType | read-only | mandatory | The connected device type, notAvailable(99) if unknown or none |
| 1.3.6.1.4.1.343.6.10.8.2.1.5 | ColumnmatrixPortMajVer | read-only | mandatory | Major Version of matrix module shared memory layout supported |
| 1.3.6.1.4.1.343.6.10.8.2.1.6 | ColumnmatrixPortMinVer | read-only | mandatory | Minor Version of matrix module shared memory layout supported |
| 1.3.6.1.4.1.343.6.10.8.2.1.7 | ColumnmatrixPortMac | read-only | mandatory | Mac address of the device connected to a specific matrix port. If the device does not have a mac address it will be zero |
| 1.3.6.1.4.1.343.6.10.8.2.1.8 | ColumnmatrixPortIp | read-write | mandatory | IP address of the device connected to a specific matrix port. If the device does not have an IP address it will be zero |
| 1.3.6.1.4.1.343.6.10.8.2.1.9 | ColumnmatrixPortSubnetMask | read-write | mandatory | IP subnet mask of the device connected to a specific matrix port. |
| 1.3.6.1.4.1.343.6.10.8.2.1.10 | ColumnmatrixPortGateway | read-write | mandatory | IP gateway of the device connected to a specific matrix port. |
| 1.3.6.1.4.1.343.6.10.8.3 | ScalarmatrixLastChange | read-only | mandatory | Timestamp for last change in matrix tables on any Matrix module |
| 1.3.6.1.4.1.343.6.10.9 | Nodemediamodules | |||
| 1.3.6.1.4.1.343.6.10.9.1 | TablemediaModuleTable | not-accessible | mandatory | Possible values of indices are 1..moduleMaxMediaModules |
| 1.3.6.1.4.1.343.6.10.9.1.1 | RowmediaModuleEntry | not-accessible | mandatory | Possible values of indices are 1..stackMaxChassis, 1..chassisMaxModules and 1..moduleMaxMediaModules |
| 1.3.6.1.4.1.343.6.10.9.1.1.1 | ColumnmoduleMode | read-write | mandatory | Hardware mode for media module. Stack mode is 1 (connected to stack), Stand alone mode is 2 (connected to switch). |
| 1.3.6.1.4.1.343.6.10.9.1.1.2 | ColumnmatrixAttachmentPort | read-only | mandatory | Returns the port number of the Matrix port the uplink mmodule is attached to. NB: will return 50 for a uplink module not connected to a Matrix Module |
| 1.3.6.1.4.1.343.6.10.9.2 | ScalarmediaModuleChange | read-only | mandatory | The value of sysUpTime after any mediamoduletype has changed |