IPL
333 objects
This MIB defines the objects used to communicate with and control the Communications & Power Industries IPL 950 series ACS.
Imported Objects
| SNMPv2-SMI | enterprises MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1414 | Identitycpisat | This MIB defines the objects used to communicate with and control the Communications & Power Industries IPL 950 series ACS. | ||
| 1.3.6.1.4.1.1414.1 | Nodepcd | |||
| 1.3.6.1.4.1.1414.1.1 | Nodeproducts | |||
| 1.3.6.1.4.1.1414.1.1.3 | Nodeipl | |||
| 1.3.6.1.4.1.1414.1.1.3.1 | NodeacuUnitInfo | |||
| 1.3.6.1.4.1.1414.1.1.3.1.1 | ScalaruiVersionNumber | read-only | current | UI version number. |
| 1.3.6.1.4.1.1414.1.1.3.1.2 | ScalaruiCreationDate | read-only | current | UI creation date. |
| 1.3.6.1.4.1.1414.1.1.3.1.3 | ScalaruiSerialNumber | read-only | current | UI serial number. |
| 1.3.6.1.4.1.1414.1.1.3.2 | NodeacuSummaryStatus | |||
| 1.3.6.1.4.1.1414.1.1.3.2.1 | ScalarssAz | read-only | current | This is the azimuth position of the antenna in the local coordinate frame. AZ = 0 is pointing north, AZ = 90 is east, etc. Its value will be between 0.0 and 35… |
| 1.3.6.1.4.1.1414.1.1.3.2.2 | ScalarssCableWrap | read-only | current | This is an indication showing the state of the cable-wrap switch. Limited motion is reported if the system does not have a cable wrap switch. |
| 1.3.6.1.4.1.1414.1.1.3.2.3 | ScalarssEl | read-only | current | This is the elevation position of the antenna in the local coordinate frame. EL = 0 is pointing at the horizon, EL = 90 is pointing at zenith. Its value will b… |
| 1.3.6.1.4.1.1414.1.1.3.2.4 | ScalarssPol | read-only | current | This is the polarization position and its value will be between 0.0 and 359.9 degrees. |
| 1.3.6.1.4.1.1414.1.1.3.2.5 | ScalarssLat | read-only | current | This is the latitude position of the RF boresite in degrees north. Its value will be between -90.00 and 90.00. |
| 1.3.6.1.4.1.1414.1.1.3.2.6 | ScalarssLon | read-only | current | This is the longitude position of the RF boresite in degrees east. Its value will be between 0.00 and 359.99. |
| 1.3.6.1.4.1.1414.1.1.3.2.7 | ScalarssAzElMode | read-only | current | This is the current ACU azimuth/elevation fundamental mode. Use this object along with the ssAzElSubMode to determine the actual operational state of the anten… |
| 1.3.6.1.4.1.1414.1.1.3.2.8 | ScalarssAzElSubMode | read-only | current | This is the current ACU azimuth/elevation fundamental sub mode. Valid sub modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.9 | ScalarssAzElEnhMode | read-only | current | This is the current ACU azimuth/elevation enhanced mode. Use this object along with the ssAzElEnhSubMode to determine the actual operational state of the anten… |
| 1.3.6.1.4.1.1414.1.1.3.2.10 | ScalarssAzElEnhSubMode | read-only | current | This is the current ACU azimuth/elevation enhanced sub mode. Valid sub modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.11 | ScalarssPolMode | read-only | current | This is the current ACU polarization mode. Valid modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.12 | ScalarssRxSignal | read-only | current | This is the RF receive signal level in dBm. Its value will be between 0 and -99.9. |
| 1.3.6.1.4.1.1414.1.1.3.2.13 | ScalarssFaults | read-only | current | This is the summary fault indication, which tells that faults either do or do not exist. |
| 1.3.6.1.4.1.1414.1.1.3.2.14 | ScalarssUnackedFaults | read-only | current | This is the summary fault indication, which tells that unacknowledged faults either do or do not exist. |
| 1.3.6.1.4.1.1414.1.1.3.2.15 | ScalarssLowSignal | read-only | current | This is the status indication, which tells whether or not the tracking signal is OK to use for tracking. |
| 1.3.6.1.4.1.1414.1.1.3.2.16 | ScalarssOnTarget | read-only | current | This is the status indication, which tells whether or not the antenna is positioned at the current position command. |
| 1.3.6.1.4.1.1414.1.1.3.2.17 | ScalarssFullStatus | read-only | current | This is the combined, full status and fault message. It is a hexadecimal representation of eight bits of status for each status byte. A 1 indicates the fault o… |
| 1.3.6.1.4.1.1414.1.1.3.2.18 | ScalarssActiveFaults | read-only | current | This message contains all active faults in the ACU. This is a string of variable length with each fault separated by the carriage return, newline (\r\n) escape… |
| 1.3.6.1.4.1.1414.1.1.3.2.19 | ScalarssStatusMessages | read-only | current | This message contains all current status messages from the ACU. This is a string of variable length with each status separated by the carriage return, newline … |
| 1.3.6.1.4.1.1414.1.1.3.2.20 | ScalarssAntennaApertureSize | read-only | current | This is the antenna aperture size measured in meters. Used mainly to compute beam width. |
| 1.3.6.1.4.1.1414.1.1.3.2.21 | ScalarssAzCmnd | read-only | current | This is the azimuth position command in the local coordinate frame. AZ = 0 is pointing north, AZ = 90 is east, etc. Its value will be between 0.0 and 359.9 deg… |
| 1.3.6.1.4.1.1414.1.1.3.2.22 | ScalarssElCmnd | read-only | current | This is the elevation position command in the local coordinate frame. EL = 0 is pointing at the horizon, EL = 90 is pointing at zenith. Its value will be betwe… |
| 1.3.6.1.4.1.1414.1.1.3.2.23 | ScalarssPolCmnd | read-only | current | This is the polarization position command and its value will be between 0.0 and 359.9 degrees. |
| 1.3.6.1.4.1.1414.1.1.3.2.24 | ScalarssAzOff | read-only | current | This is the azimuth offset from the azimuth position command of the fundamental mode. This is the portion of the position command determined by the enhanced mo… |
| 1.3.6.1.4.1.1414.1.1.3.2.25 | ScalarssElOff | read-only | current | This is the elevation offset from the elevation position command of the fundamental mode. This is the portion of the position command determined by the enhance… |
| 1.3.6.1.4.1.1414.1.1.3.2.26 | ScalarssPolOff | read-only | current | This is the polarization offset from the pol position command of the pol mode. This should be equal to the pol manual offset. |
| 1.3.6.1.4.1.1414.1.1.3.2.27 | ScalarssPol2 | read-only | current | This is the polarization2 position and its value will be between 0.0 and 359.9 degrees. |
| 1.3.6.1.4.1.1414.1.1.3.2.28 | ScalarssPol2Cmnd | read-only | current | This is the polarization2 position command and its value will be between 0.0 and 359.9 degrees. |
| 1.3.6.1.4.1.1414.1.1.3.2.29 | ScalarssPol2Off | read-only | current | This is the polarization2 offset from the pol2 position command of the pol mode. This should be equal to the pol2 manual offset. |
| 1.3.6.1.4.1.1414.1.1.3.2.30 | ScalarssAzElEnhSecMode | read-only | current | This is the current ACU azimuth/elevation enhanced sec mode. Use this object along with the ssAzElEnhSecSubMode to determine the actual operational state of th… |
| 1.3.6.1.4.1.1414.1.1.3.2.31 | ScalarssAzElEnhSecSubMode | read-only | current | This is the current ACU azimuth/elevation enhanced sub mode. Valid sub modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.32 | ScalarssPointSubMode | read-only | current | This is the current ACU Point sub mode. Valid sub modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.33 | ScalarssTrackSubMode | read-only | current | This is the current ACU azimuth/elevation enhanced sub mode. Valid sub modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.34 | ScalarssAcquireSubMode | read-only | current | This is the current ACU azimuth/elevation enhanced sub mode. Valid sub modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.2.35 | ScalarssAntennaType | read-only | current | Read the type of the antenna. |
| 1.3.6.1.4.1.1414.1.1.3.2.36 | ScalarssPol2Mode | read-only | current | This is the current ACU mode for the second polarization axis. Valid modes are shown in the SYNTAX section above. |
| 1.3.6.1.4.1.1414.1.1.3.3 | NodeacuOperations | |||
| 1.3.6.1.4.1.1414.1.1.3.3.1 | ScalaropFModeCtl | read-write | current | This command shall place the ACS in the desired AZ/EL fundamental mode. There is no mode restriction when issuing these commands. Only the write for this objec… |
| 1.3.6.1.4.1.1414.1.1.3.3.2 | ScalaropEModeCtl | read-write | current | This command shall place the ACS in the desired AZ/EL enhanced mode. There is no mode restriction when issuing these commands. Only the write for this object i… |
| 1.3.6.1.4.1.1414.1.1.3.3.3 | ScalaropCurrFreqOID | read-write | current | This is the OID used to set the current operational frequency dataset to the Direct dataset. |
| 1.3.6.1.4.1.1414.1.1.3.3.4 | TableopRFTable | not-accessible | current | This is the table of RF entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1 | RowopRFTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.1 | ColumnopRFIndex | read-only | current | This is the index of the RF data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.2 | ColumnopRFSlope | read-write | current | The slope of the analog tracking signal in dB/V. The range is 0.1 to 100.00000. This parameter has no impact on this system since there is no analog tracking s… |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.3 | ColumnopRFOffset | read-write | current | A signal offset in dB applied to the tracking signal tyoically to normalize it. The range is -100.0000 to +100.0000 dB. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.4 | ColumnopRFFreq | read-write | current | This is the frequency of the track signal from the target satellite in GHz. For sets, the TOTAL length of this string is limited to 10 characters. For sets, th… |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.5 | ColumnopRFBandwidth | read-write | current | This selects the frequency bandwidth that the tracking receiver uses to detect the track signal. Setting depends on TRU type: for analog: 1 = 2.5 kHz; 2 = 6.0 … |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.6 | ColumnopRFPolSelect | read-write | current | This is the antenna's Polarization orientation. Setting depends on polarization type set by the Pol Mode field: for Linear: 1 = vert, 2 = horz for Circular: 1 … |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.7 | ColumnopRFActiveSearch | read-write | current | This determines whether (2) or not (1) the RF paths are searched to see which RF path yields the highest signal strength. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.8 | ColumnopRFElFeed | read-write | current | The elevation feed offset in degrees. Range is -5.000 to +5.000. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.9 | ColumnopRFXelFeed | read-write | current | The cross-elevation feed offset in degrees. Range is -5.000 to +5.000. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.10 | ColumnopRFNBSweep | read-write | current | The narrowband sweep width. The range to search for the carrier of the beacon in kHz. The range is 40.0 to 145.0. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.11 | ColumnopRFName | read-write | current | This is the name given to the RF data set. For sets, the TOTAL length of this string is limited to 21 characters. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.12 | ColumnopRFPolMode | read-write | current | This is the antenna's Polarization type. The Pol Select field in the RF Table should be updated after modifying this value. |
| 1.3.6.1.4.1.1414.1.1.3.3.4.1.13 | ColumnopRFPol2Select | read-write | current | This is the antenna's Polarization orientation for the second of two polarization axes. Setting depends on polarization type: for Linear: 1 = vert, 2 = horz fo… |
| 1.3.6.1.4.1.1414.1.1.3.3.5 | ScalaropCurrConfigOID | read-write | current | This is the OID used to set the current operational configuration dataset to the Direct dataset. |
| 1.3.6.1.4.1.1414.1.1.3.3.6 | TableopConfigTable | not-accessible | current | This is the table of configurations. |
| 1.3.6.1.4.1.1414.1.1.3.3.6.1 | RowopConfigTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.6.1.1 | ColumnopConfigIndex | read-only | current | This is the index of the RF data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.6.1.2 | ColumnopConfigAcquire | read-write | current | This acquire threshold sets the track signal level, in dB, at which scanning will start. Its range is from -99.9 to 0.0, and its precision is to one decimal pl… |
| 1.3.6.1.4.1.1414.1.1.3.3.6.1.3 | ColumnopConfigLowSignal | read-write | current | This low-signal threshold sets the track signal level, in dB, at which scanning will stop and/or steptracking will begin. Its range is from -99.9 to 0.0, and i… |
| 1.3.6.1.4.1.1414.1.1.3.3.6.1.5 | ColumnopConfigName | read-only | current | This is the name given to this config data set. For sets, the TOTAL length of this string is limited to 21 characters. |
| 1.3.6.1.4.1.1414.1.1.3.3.7 | ScalaropJogAzimuth | read-write | current | This commands a CW (+) or CCW (-) jog of the azimuth axis. The currently set value can also be recalled. |
| 1.3.6.1.4.1.1414.1.1.3.3.8 | ScalaropJogElevation | read-write | current | This commands an upward (+) or downward (-) jog of the elevation axis. The currently set value can also be recalled. |
| 1.3.6.1.4.1.1414.1.1.3.3.9 | ScalaropJogPolarization | read-write | current | This commands a CW (+) or CCW (-) jog of the polarization axis. The currently set value can also be recalled. |
| 1.3.6.1.4.1.1414.1.1.3.3.10 | ScalaropManOffAzimuth | read-write | current | This applies the provided manual offset to the azimuth position command. CW (+) or CCW (-). The range is +20.000 to -20.000 degrees. The current manual offset … |
| 1.3.6.1.4.1.1414.1.1.3.3.11 | ScalaropManOffElevation | read-write | current | This applies the provided manual offset to the elevation position command. CW (+) or CCW (-). The range is +20.000 to -20.000 degrees. The current manual offse… |
| 1.3.6.1.4.1.1414.1.1.3.3.12 | ScalaropManOffPolarization | read-write | current | This applies the provided manual offset to the pol position command. CW (+) or CCW (-). The range is +20.000 to -20.000 degrees. The current manual offset can … |
| 1.3.6.1.4.1.1414.1.1.3.3.13 | ScalaropAzAxisDisable | read-write | current | This command shall enable or disable the azimuth axis. |
| 1.3.6.1.4.1.1414.1.1.3.3.14 | ScalaropElAxisDisable | read-write | current | This command shall enable or disable the elevation axis. |
| 1.3.6.1.4.1.1414.1.1.3.3.15 | ScalaropPlAxisDisable | read-write | current | This command shall enable or disable the polarization axis. |
| 1.3.6.1.4.1.1414.1.1.3.3.16 | ScalaropAzEncoderOffset | read-write | current | This is an offset that is applied directly to the azimuth gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.17 | ScalaropAzEncoderRotation | read-write | current | This is the direction in which the encoder offset is applied to the gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.18 | ScalaropAzEncoderSF | read-write | current | This is a scale factor that is applied directly to the azimuth gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.19 | ScalaropElEncoderOffset | read-write | current | This is an offset that is applied directly to the elevation gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.20 | ScalaropElEncoderRotation | read-write | current | This is the direction in which the encoder offset is applied to the gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.21 | ScalaropElEncoderSF | read-write | current | This is a scale factor that is applied directly to the elevation gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.22 | ScalaropPlEncoderOffset | read-write | current | This is an offset that is applied directly to the polarization gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.23 | ScalaropPlEncoderRotation | read-write | current | This is the direction in which the encoder offset is applied to the gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.24 | ScalaropPlEncoderSF | read-write | current | This is a scale factor that is applied directly to the polarization gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.25 | ScalaropLatchedFaults | read-write | current | Send this command to enable or disable the latched faults in the ACU. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.26 | ScalaropNORADgpsTime | read-write | current | This is the time of the ACU, mainly used for the NORAD mode. It can also be externally set here. The format is hh:mm:ss:ddd:yyyy. This set can only be issued w… |
| 1.3.6.1.4.1.1414.1.1.3.3.27 | TableopPresetTable | not-accessible | current | This is the table containing details of the preset mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1 | RowpresetTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1.1 | ColumnopPresetSatNum | read-only | current | This is the index of the preset satellites. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1.2 | ColumnopPresetSatName | read-only | current | This is the preset satellite name. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1.3 | ColumnopPresetAz | read-write | current | This is the Azimuth preset command. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1.4 | ColumnopPresetEl | read-write | current | This is the Elevation preset command. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1.5 | ColumnopPresetPol | read-write | current | This is the Polarization preset command. |
| 1.3.6.1.4.1.1414.1.1.3.3.27.1.6 | ColumnopPresetPol2 | read-write | current | This is the Polarization preset command for the second polarization axis. |
| 1.3.6.1.4.1.1414.1.1.3.3.28 | ScalaropPresetSatCommand | read-write | current | Write this value followed by the appropriate opFModeCtl and/or opPModeCtl and/or opP2ModeCtl value to put the antenna into Preset mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.29 | ScalaropClearLatchedFaults | read-write | current | If opLatchedFaults is enabled, and statuses or faults are present that the operator would like to clear, then send this command. This will clear all currently … |
| 1.3.6.1.4.1.1414.1.1.3.3.30 | ScalaropPModeCtl | read-write | current | This command shall place the ACS in the desired polarization mode. There is no mode restriction when issuing these commands. Only the write for this object is … |
| 1.3.6.1.4.1.1414.1.1.3.3.31 | ScalaropAzPDAngle | read-write | current | Write this value and the OpElPDAngle value followed by the appropriate opFModeCtl value to put the antenna into Position Designate mode. Range is 0.0000 to 359… |
| 1.3.6.1.4.1.1414.1.1.3.3.32 | ScalaropElPDAngle | read-write | current | Write this value and the OpAzPDAngle value followed by the appropriate opFModeCtl value to put the antenna into Position Designate mode. Range is -5.0000 to 95… |
| 1.3.6.1.4.1.1414.1.1.3.3.33 | ScalaropPolPDAngle | read-write | current | Write this value followed by the appropriate opPModeCtl value to put the antenna into Pol Position Designate mode. Range is 0.0000 to 359.999 degrees. |
| 1.3.6.1.4.1.1414.1.1.3.3.34 | ScalaropLonPDAngle | read-write | current | Write this value and the OpLatPDAngle value followed by the appropriate opFModeCtl value to put the antenna into Position Designate mode. Range is -359.999 to … |
| 1.3.6.1.4.1.1414.1.1.3.3.35 | ScalaropLatPDAngle | read-write | current | Write this value and the OpLonPDAngle value followed by the appropriate opFModeCtl value to put the antenna into Position Designate mode. Range is -95.0000 to … |
| 1.3.6.1.4.1.1414.1.1.3.3.36 | TableopGeoPresetTable | not-accessible | current | This is the table containing details of the geo preset mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.36.1 | RowgeopresetTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.36.1.1 | ColumnopGeoPresetSatNum | read-only | current | This is the index of the geo preset positions. |
| 1.3.6.1.4.1.1414.1.1.3.3.36.1.2 | ColumnopGeoPresetSatName | read-only | current | This is the geo preset satellite name. |
| 1.3.6.1.4.1.1414.1.1.3.3.36.1.3 | ColumnopGeoPresetLon | read-write | current | This is the longitude preset command. |
| 1.3.6.1.4.1.1414.1.1.3.3.36.1.4 | ColumnopGeoPresetLat | read-write | current | This is the latitude preset command. |
| 1.3.6.1.4.1.1414.1.1.3.3.37 | ScalaropGeoPresetSatCommand | read-write | current | Write this value followed by the appropriate opFModeCtl and/or opPModeCtl value to put the antenna into Geo Preset mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.39 | ScalaropOptrackClearCommand | read-write | current | Write this value to clear the associated Optrack data set. |
| 1.3.6.1.4.1.1414.1.1.3.3.40 | ScalaropOptrackChargeCommand | read-write | current | Write this value to charge the associated Optrack data set. The opOptrackChargeSource determines the source data used to precharge this data set. |
| 1.3.6.1.4.1.1414.1.1.3.3.41 | ScalaropOptrackChargeSource | read-write | current | Determines the source data used to precharge Optrack data sets. The source data that can used are the Intelsat data sets of which there are 40. |
| 1.3.6.1.4.1.1414.1.1.3.3.42 | ScalaropStowPosCommand | read-write | current | Write this value followed by the appropriate opFModeCtl value to put the antenna into Stow mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.43 | TableopIntelsatTable | not-accessible | current | This is the table containing details of the intelsat data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1 | RowintelsatTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.1 | ColumnopIntelsatNum | read-only | current | This is the index of the intelsat data set table. |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.2 | ColumnopIntelsatName | read-only | current | This is the intelsat data set name. |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.3 | ColumnopIntelsatLm0 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.4 | ColumnopIntelsatLm1 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.5 | ColumnopIntelsatLm2 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.6 | ColumnopIntelsatLonc | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.7 | ColumnopIntelsatLonc1 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.8 | ColumnopIntelsatLons | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.9 | ColumnopIntelsatLons1 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.10 | ColumnopIntelsatLatc | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.11 | ColumnopIntelsatLatc1 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.12 | ColumnopIntelsatLats | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.13 | ColumnopIntelsatLats1 | read-write | current | One of the standard 11 parameters contain in Intelsat ephemeris data. This is the same mnemonic used by Intelsat on their transmitted reports. NOTE: That intel… |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.14 | ColumnopIntelsatEpochTime | read-write | current | This is the epoch time associated with the 11 Intelsat parameters. The format mm:dd:yyyy<sp>hh:mm:ss. |
| 1.3.6.1.4.1.1414.1.1.3.3.43.1.16 | ColumnopIntelsatIsValid | read-write | current | Indicates whether the Intelsat dataset has been validated. Write can only clear this indicator, essentially deleting the dataset. To set this indicator, use op… |
| 1.3.6.1.4.1.1414.1.1.3.3.44 | ScalaropIntelsatSatCommand | read-write | current | Write this value followed by the appropriate opFModeCtl value to put the antenna into Intelsat mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.45 | ScalaropIntelsatCheckCommand | read-write | current | Write this value to initiate a check of the associated Intelsat data. If the check passes, opIntelsatIsValid will be set. If not, it will be cleared. The check… |
| 1.3.6.1.4.1.1414.1.1.3.3.46 | ScalaropIntelsatCheckLat | read-write | current | This is the latitude that the associated Intelsat data set is supposed to compute to at opIntelsatCheckTime. |
| 1.3.6.1.4.1.1414.1.1.3.3.47 | ScalaropIntelsatCheckLon | read-write | current | This is the longitude that the associated Intelsat data set is supposed to compute to at opIntelsatCheckTime. |
| 1.3.6.1.4.1.1414.1.1.3.3.48 | ScalaropIntelsatCheckTime | read-write | current | This is the time (in hours past the epoch time) used by the check process. Typically this value is 170.0 in Intelsat transmission reports. |
| 1.3.6.1.4.1.1414.1.1.3.3.49 | ScalaropNoradObjectCommand | read-write | current | Write this value followed by the appropriate opFModeCtl value to put the antenna into Norad mode. The format of the string must be a length of 5 numeric digits |
| 1.3.6.1.4.1.1414.1.1.3.3.50 | ScalaropNoradDeleteAll | read-write | current | Write to delete all stored Norad two-line element sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.51 | ScalaropNoradListAll | read-only | current | An command-delimited ordered list of all stored Norad objects. Example: 12345,45678,87621 |
| 1.3.6.1.4.1.1414.1.1.3.3.52 | ScalaropNoradObjectLoad | read-write | current | A string in the standard Norad two-line element format. When written, the object number in the TLE is recorded in opNoradRecallObject so that the next read her… |
| 1.3.6.1.4.1.1414.1.1.3.3.53 | ScalaropNoradRecallObject | read-write | current | The object number format is a string that must be a length of 5 numeric digits. It is used in conjunction with opNoradObjectLoad. |
| 1.3.6.1.4.1.1414.1.1.3.3.54 | ScalaropNoradObjectDelete | read-write | current | A text string of 5 numeric digits representing an object number. When written, the stored TLE associated with that object number is deleted. A read provides th… |
| 1.3.6.1.4.1.1414.1.1.3.3.55 | ScalaropNoradOptrackChargeCommand | read-write | current | Write this value to charge the associated Optrack data set. The opNoradOptrackChargeSource determines the source data used to precharge this data set. |
| 1.3.6.1.4.1.1414.1.1.3.3.56 | ScalaropNoradOptrackChargeSource | read-write | current | Determines the source data used to precharge Optrack data sets. The source data that can used are the Norad data sets. An object number for the desired Norad d… |
| 1.3.6.1.4.1.1414.1.1.3.3.57 | ScalaropSteptrackTrackFlags | read-write | current | Write this value, followed by the appropriate opEModeCtl or opTrackModeCtl value, to put the antenna into Steptrack mode. 0: Use manual Track dataset 1: Use au… |
| 1.3.6.1.4.1.1414.1.1.3.3.60 | ScalaropBoxScanFlags | read-write | current | Write this value followed by the appropriate opEModeCtl or opAcquireModeCtl value to put the antenna into Box Scan mode. 0 for the manual set 1 for the automat… |
| 1.3.6.1.4.1.1414.1.1.3.3.61 | ScalaropJogPolarization2 | read-write | current | This commands a CW (+) or CCW (-) jog of the polarization2 axis. The currently set value can also be recalled. |
| 1.3.6.1.4.1.1414.1.1.3.3.62 | ScalaropManOffPolarization2 | read-write | current | This applies the provided manual offset to the pol2 position command. CW (+) or CCW (-). The range is +20.000 to -20.000 degrees. The current manual offset can… |
| 1.3.6.1.4.1.1414.1.1.3.3.63 | TableopMonoRFTable | not-accessible | current | This is the table of Monopulse RF entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1 | RowopMonoRFTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.1 | ColumnopMonoRFIndex | read-only | current | This is the index of the Monopulse RF data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.2 | ColumnopMonoRFELErrorSlope | read-write | current | The slope of the error signal in degrees per volt (0.0 to 200.00) (declination slope). This is a legacy parameter that has no impact on operation. |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.3 | ColumnopMonoRFXELErrorSlope | read-write | current | The slope of the error signal in degrees per volt (0.0 to 200.00) (declination slope). This is a legacy parameter that has no impact on operation. |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.4 | ColumnopMonoRFELNullOffset | read-write | current | The null offset in degrees (-1.000 to 1.000) (declination offset). |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.5 | ColumnopMonoRFXELNullOffset | read-write | current | The null offset in degrees (-1.000 to 1.000) (cross declination offset). |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.6 | ColumnopMonoRFPOLRefAngle | read-write | current | The Polarization Angle at which the Monopulse RF Chain is correctly phased (0.0 to 359.999). If no POL, set to 0.0. |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.7 | ColumnopMonoRFELPhaseShift | read-write | current | The Elevation (declination) Phase Shifter Angle at the reference Polarization Angle (0.0 to 359.999). |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.8 | ColumnopMonoRFXELPhaseShift | read-write | current | The Cross-Elevation (declination) Phase Shifter Angle at the reference Polarization Angle (0.0 to 359.999). |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.9 | ColumnopMonoRFPhaseShiftMode | read-write | current | The phase shift mode. A 0 turns scanning off (monopulse is not available). A 1 indicates constant scanning (this is the normal selection). A 2 gives random sca… |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.10 | ColumnopMonoRFPhaseShiftSelect | read-write | current | The phase shift select mode. A 0 indicates manual mode and uses the manual phase shift settings. A 1 indicates table and uses the phase shift values in the tab… |
| 1.3.6.1.4.1.1414.1.1.3.3.63.1.11 | ColumnopMonoRFPolErrorRotation | read-write | current | Polarization error rotation. A 0 indicates rotation is off. A 1 indicates rotation is on. If no POL, set to 0. |
| 1.3.6.1.4.1.1414.1.1.3.3.64 | TableopMonoParmTable | not-accessible | current | This is the table of Monopulse Parameters entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1 | RowopMonoParmTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.1 | ColumnopMonoParmIndex | read-only | current | This is the index of the Monopulse Parameter data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.2 | ColumnopMonoParmAZELTargetVel | read-write | current | The target velocity used for monopulse rate error detection (0.00001 to 20.0 degs). |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.3 | ColumnopMonoParmErrThreshActive | read-write | current | Error signal threshold active if TRUE. |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.4 | ColumnopMonoParmAZErrorThreshold | read-write | current | Error signal threshold |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.5 | ColumnopMonoParmELErrorThreshold | read-write | current | Error signal threshold |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.6 | ColumnopMonoParmDeadbandActive | read-write | current | Deadband active if TRUE |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.7 | ColumnopMonoParmAZDeadband | read-write | current | deadband value |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.8 | ColumnopMonoParmELDeadband | read-write | current | deadband value |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.9 | ColumnopMonoParmAZHysterisis | read-write | current | hysterisis for deadband |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.10 | ColumnopMonoParmELHysterisis | read-write | current | hysterisis for deadband |
| 1.3.6.1.4.1.1414.1.1.3.3.64.1.11 | ColumnopMonoParmDeadbandDelay | read-write | current | delay after deadband satisfied |
| 1.3.6.1.4.1.1414.1.1.3.3.65 | TableopPhaseShiftTable | not-accessible | current | This is the table of Phase Shift entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.65.1 | RowopPhaseShiftTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.65.1.1 | ColumnopPhaseShiftIndex | read-only | current | This is the index of the Phase Shift data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.65.1.2 | ColumnopPhaseShiftBitPattern | read-write | current | Phase Shift Bit Pattern |
| 1.3.6.1.4.1.1414.1.1.3.3.65.1.3 | ColumnopPhaseShiftXEL | read-write | current | The Azimuth Axis phase shift in degrees (0 - 359.999). |
| 1.3.6.1.4.1.1414.1.1.3.3.65.1.4 | ColumnopPhaseShiftEL | read-write | current | The Elevation Axis phase shift in degrees (0 - 359.999). |
| 1.3.6.1.4.1.1414.1.1.3.3.66 | TableopMasterPhaseShiftTable | not-accessible | current | This is the table of Phase Shift entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.66.1 | RowopMasterPhaseShiftTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.66.1.1 | ColumnopMasterPhaseShiftIndex | read-only | current | This is the index of the Phase Shift data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.66.1.2 | ColumnopMasterPhaseShiftBitPattern | read-write | current | Phase Shift Bit Pattern |
| 1.3.6.1.4.1.1414.1.1.3.3.66.1.3 | ColumnopMasterPhaseShiftName | read-write | current | An alphanumeric name assigned to this master phase shift table entry. This can be 0 to 22 characters. |
| 1.3.6.1.4.1.1414.1.1.3.3.67 | ScalaropTrackModeCtl | read-write | current | This command shall place the ACU in the desired track mode. Only the write for this object is meaningful. The read always returns 0. |
| 1.3.6.1.4.1.1414.1.1.3.3.68 | ScalaropAcquireModeCtl | read-write | current | This command shall place the ACU in the desired acquire mode. Only the write for this object is meaningful. The read always returns 0. |
| 1.3.6.1.4.1.1414.1.1.3.3.69 | TableopOptConfigTable | not-accessible | current | This is the table of Optrack Config entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.69.1 | RowopOptConfigTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.69.1.1 | ColumnopOptConfigIndex | read-only | current | This is the index of the Phase Shift data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.69.1.2 | ColumnopOptConfigDataDegradedThreshhold | read-write | current | Recycle level in dB (-50.0 to 0.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.69.1.3 | ColumnopOptConfigDataCycleTime | read-write | current | Scan cycle time in minutes (10.0, 20.0, or 30.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.69.1.4 | ColumnopOptConfigDataTrackType | read-write | current | 0 for steptrack, 1 for monopulse |
| 1.3.6.1.4.1.1414.1.1.3.3.70 | ScalaropGeoScanFlags | read-write | current | Write this value followed by the appropriate opAcquireModeCtl value to put the antenna into GEO Scan mode. 0 for the manual set 1 for the automatic set. |
| 1.3.6.1.4.1.1414.1.1.3.3.71 | ScalaropProfileNumberCommand | read-write | current | This will set the profile number for cli commands such as AUTOPP. This must be set prior to those commands |
| 1.3.6.1.4.1.1414.1.1.3.3.72 | ScalaropAutoPhasePeakingRequired | read-write | current | AUTOPP and AUTOPP? commands. Must use opProfileCommandNumber to set desired profile number before this command |
| 1.3.6.1.4.1.1414.1.1.3.3.73 | ScalaropPl2AxisDisable | read-write | current | This command shall enable or disable the second polarization axis. |
| 1.3.6.1.4.1.1414.1.1.3.3.74 | ScalaropPl2EncoderOffset | read-write | current | This is an offset that is applied directly to the second polarization axis gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.75 | ScalaropPl2EncoderRotation | read-write | current | This is the direction in which the encoder offset is applied to the gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.76 | ScalaropPl2EncoderSF | read-write | current | This is a scale factor that is applied directly to the second polarization axis gimbal angle. This set can only be issued when ssAzElMode is equal to stop(1). |
| 1.3.6.1.4.1.1414.1.1.3.3.77 | ScalaropP2ModeCtl | read-write | current | This command shall place the ACS in the desired mode for the second polarization axis. There is no mode restriction when issuing these commands. Only the write… |
| 1.3.6.1.4.1.1414.1.1.3.3.78 | ScalaropPol2PDAngle | read-write | current | Write this value followed by the appropriate opP2ModeCtl value to put the antenna into Pol2 Position Designate mode. Range is 0.0000 to 359.9999 degrees. |
| 1.3.6.1.4.1.1414.1.1.3.3.79 | TableopGeoScanTable | not-accessible | current | This is the table of GeoScan entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1 | RowopGeoScanTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.1 | ColumnopGeoScanIndex | read-only | current | This is the index of the Geo Scan data sets. Data set 102 is read only |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.2 | ColumnopGeoScanChoice | read-write | current | Geo Scan choice |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.3 | ColumnopGeoScanLatLength | read-write | current | Length in degrees latitude (0.001 to 30.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.4 | ColumnopGeoScanLonWidth | read-write | current | Width in degrees longitude (0.001 to 180.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.5 | ColumnopGeoScanVel | read-only | current | The velocity at which the scan process will proceed. In deg/sec. |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.6 | ColumnopGeoScanSeparation | read-write | current | The radial distance separating successive scan passes. In dB. Only applies to manual mode |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.7 | ColumnopGeoScanSepInDegrees | read-only | current | Separation in degrees (0.01 to 10.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.79.1.8 | ColumnopGeoScanLockTime | read-write | current | Acquire Lock Time in seconds (0.1 to 20.0). Only applies to manual mode |
| 1.3.6.1.4.1.1414.1.1.3.3.80 | TableopBoxScanTable | not-accessible | current | This is the table of BoxScan entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1 | RowopBoxScanTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.1 | ColumnopBoxScanIndex | read-only | current | This is the index of the Box Scan data sets. Data set 102 is read only |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.2 | ColumnopBoxScanChoice | read-write | current | Geo Scan choice |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.3 | ColumnopBoxScanType | read-write | current | Box Scan type |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.4 | ColumnopBoxScanLength | read-write | current | Max size to which the scan pattern length may grow. (0.001 to 20.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.5 | ColumnopBoxScanWidth | read-write | current | Max size to which the scan pattern width may grow. (0.001 to 20.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.6 | ColumnopBoxScanVel | read-only | current | The velocity at which the scan process will proceed. In deg/sec. (0.01 to 10.0) |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.7 | ColumnopBoxScanSeparation | read-write | current | The radial distance separating successive scan passes. In dB. (0.001 to 10.0). Only applies to manual mode |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.8 | ColumnopBoxScanSepInDegrees | read-only | current | Separation in degrees. |
| 1.3.6.1.4.1.1414.1.1.3.3.80.1.9 | ColumnopBoxScanLockTime | read-write | current | Acquire Lock Time in seconds (0.1 to 20.0). Only applies to manual mode |
| 1.3.6.1.4.1.1414.1.1.3.3.81 | TableopSteptrackTable | not-accessible | current | This is the table of Steptrack entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1 | RowopSteptrackTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.1 | ColumnopSteptrackIndex | read-only | current | This is the index of the Steptrack data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.2 | ColumnopSteptrackDegradedSignal | read-write | current | Degraded Signal Threshold. (-50.0 to 0.0). |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.3 | ColumnopSteptrackIntegrationTime | read-write | current | Steptrack Integration time in seconds. Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.4 | ColumnopSteptrackBoxStepSize | read-write | current | Steptrack Box Step Size. (5.0 to 20.0). Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.5 | ColumnopSteptrackScanCycleTime | read-write | current | Steptrack Cycle Time in minutes. (0.0 to 24.0). Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.6 | ColumnopSteptrackDataPointRejection | read-write | current | Steptrack Data Point Rejection. Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.7 | ColumnopSteptrackPeakCenterCorrections | read-write | current | Steptrack Peak Center Correction. (0.0 to 10.0). Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.8 | ColumnopSteptrackParkThreshold | read-write | current | Steptrack Park Threshold. (3.0 to 10.0). Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.9 | ColumnopSteptrackGain | read-write | current | Steptrack Gain. (0.0 to 1.0). Only for Manual Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.81.1.10 | ColumnopSteptrackInclination | read-write | current | Steptrack Inclination. (0.0 to 1.0). Only for Automatic Mode. |
| 1.3.6.1.4.1.1414.1.1.3.3.82 | TableopStowTable | not-accessible | current | This is the table of Stow entries. |
| 1.3.6.1.4.1.1414.1.1.3.3.82.1 | RowopStowTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.3.82.1.1 | ColumnopStowIndex | read-only | current | This is the index of the Stow data sets. |
| 1.3.6.1.4.1.1414.1.1.3.3.82.1.2 | ColumnopStowName | read-write | current | Stow Name. For sets, the TOTAL length of this string is limited to 20 characters. |
| 1.3.6.1.4.1.1414.1.1.3.3.82.1.3 | ColumnopStowAzAngle | read-write | current | Stow AZ Angle. (0.0 to 359.999). |
| 1.3.6.1.4.1.1414.1.1.3.3.82.1.4 | ColumnopStowElAngle | read-write | current | Stow EL Angle. (-5.0 to 95.000). |
| 1.3.6.1.4.1.1414.1.1.3.4 | NodeacuVehicle | |||
| 1.3.6.1.4.1.1414.1.1.3.4.1 | ScalarvehGPSMagVar | read-only | current | This is the amount the compass reading is deflected at the current site location due to the earth's magnetic field. Units are degrees. |
| 1.3.6.1.4.1.1414.1.1.3.4.2 | ScalarvehGPSLat | read-only | current | This is the latitude in degrees reported by the GPS equipment. Its range is from -90.0000 (south) to +90.0000 (north). |
| 1.3.6.1.4.1.1414.1.1.3.4.3 | ScalarvehGPSLon | read-only | current | This is the longitude in degrees reported by the GPS equipment. Its range is from 0.0 to 359.9999 (east). |
| 1.3.6.1.4.1.1414.1.1.3.4.4 | ScalarvehCompassHeading | read-only | current | This is the current vehicle heading as reported by the compass equipment. Units are degrees. |
| 1.3.6.1.4.1.1414.1.1.3.4.5 | ScalarvehXTilt | read-only | current | This is the current vehicle pitch in degrees as reported by the clinometer equipment. Positive indicating that the front of the vehicle is pitched upward. |
| 1.3.6.1.4.1.1414.1.1.3.4.6 | ScalarvehYTilt | read-only | current | This is the current vehicle roll in degrees as reported by the clinometer equipment. Positive indicating that the left side of the vehicle is higher than the r… |
| 1.3.6.1.4.1.1414.1.1.3.4.7 | ScalarvehGPSCurrentMode | read-only | current | This is the operational mode of the GPS. It can be one of the following: Getting Fixes, No GPS Time, PDOP is too high, No Usable Sats, 1 Useable Sat, 2 Useable… |
| 1.3.6.1.4.1.1414.1.1.3.4.8 | ScalarvehGPSQuality | read-only | current | This is a quality indicator for the GPS data. |
| 1.3.6.1.4.1.1414.1.1.3.4.9 | ScalarvehGPSTime | read-only | current | This is the time GPS time and date. The format mm<sp>dd<sp>hh:mm:ss. |
| 1.3.6.1.4.1.1414.1.1.3.4.10 | ScalarvehCompassMarkAngle | read-write | current | This is the offset in degrees that the compass is determined to be in error (off from an ideal mounting mark). |
| 1.3.6.1.4.1.1414.1.1.3.4.11 | ScalarvehCalibration | read-write | current | Write 1 to initiate the antenna calibration sequence. |
| 1.3.6.1.4.1.1414.1.1.3.4.12 | ScalarvehGPSReset | read-write | current | Write 1 to reset the GPS. |
| 1.3.6.1.4.1.1414.1.1.3.4.13 | ScalarvehGPSAltitude | read-only | current | This is the altitude reported by the GPS equipment. Its range is from -1000.00 to 1000.00. |
| 1.3.6.1.4.1.1414.1.1.3.5 | NodeacuProfile | |||
| 1.3.6.1.4.1.1414.1.1.3.5.1 | ScalarpfRun | read-write | current | This command shall place the ACS in the desired Profile execution mode. There is no mode restriction when issuing these commands. |
| 1.3.6.1.4.1.1414.1.1.3.5.2 | ScalarpfProfileListIndex | read-write | current | This selects the pfProfileSet index |
| 1.3.6.1.4.1.1414.1.1.3.5.3 | ScalarpfProfileListGroup | read-only | current | This selects the pfProfile in groups of 20. Index 1 gives 1 thru 20, Index 2, 21 thru 40, ... |
| 1.3.6.1.4.1.1414.1.1.3.5.4 | ScalarpfProfileSave | read-write | current | Save the contents of local pfProfile to desired profile number in database |
| 1.3.6.1.4.1.1414.1.1.3.5.5 | ScalarpfProfileLoad | read-write | current | Load the contents of specified profile number in database to Local profile |
| 1.3.6.1.4.1.1414.1.1.3.5.6 | ScalarpfProfileLocalName | read-write | current | This is the name given to the Profile. For sets, the TOTAL length of this string is limited to 20 characters. |
| 1.3.6.1.4.1.1414.1.1.3.5.7 | ScalarpfProfileLocalUserInfo | read-write | current | This is the Info text of the Profile. For sets, the TOTAL length of this string is limited to 80 characters. |
| 1.3.6.1.4.1.1414.1.1.3.5.8 | ScalarpfProfileLocalPointModeNum | read-write | current | This is the Point Mode of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.9 | ScalarpfProfileLocalPointDataNum | read-write | current | This is the Point Data Number of the Profile. This will vary depending on the Point Mode |
| 1.3.6.1.4.1.1414.1.1.3.5.10 | ScalarpfProfileLocalAcquireModeNum | read-write | current | This is the Acquire Mode of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.11 | ScalarpfProfileLocalAcquireDataNum | read-write | current | This is the Acquire Data Number of the Profile. This will vary depending on the Acquire Mode |
| 1.3.6.1.4.1.1414.1.1.3.5.12 | ScalarpfProfileLocalTrackModeNum | read-write | current | This is the Track Mode of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.13 | ScalarpfProfileLocalTrackDataNum | read-write | current | This is the Acquire Data Number of the Profile. This will may vary depending on the Track Mode. |
| 1.3.6.1.4.1.1414.1.1.3.5.14 | ScalarpfProfileLocalRFNum | read-write | current | This is the RFNum Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.15 | ScalarpfProfileLocalConfigNum | read-write | current | This is the ConfigNum Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.16 | ScalarpfProfileLocalPolModeNum | read-write | current | This is the Pol Mode Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.17 | ScalarpfProfileLocalPolDataNum | read-write | current | This is the Pol Data Number of the Profile. Only used for preset |
| 1.3.6.1.4.1.1414.1.1.3.5.18 | ScalarpfProfileLocalPol2ModeNum | read-write | current | This is the Pol2 Mode Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.19 | ScalarpfProfileLocalPol2DataNum | read-write | current | This is the Pol2 Data Number of the Profile. Only used for preset |
| 1.3.6.1.4.1.1414.1.1.3.5.20 | TablepfProfileTable | not-accessible | current | This is the read only table of Profile Table entries from database |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1 | RowpfProfileTableData | not-accessible | current | This contains the field descriptions for each table entry. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.1 | ColumnpfProfileIndex | read-only | current | This is the index of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.2 | ColumnpfProfileName | read-only | current | This is the name given to the Profile. For sets, the TOTAL length of this string is limited to 21 characters. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.3 | ColumnpfProfileUserInfo | read-only | current | This is the Info text of the Profile. For sets, the TOTAL length of this string is limited to 80 characters. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.4 | ColumnpfProfilePointModeNum | read-only | current | This is the Point Mode of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.5 | ColumnpfProfilePointDataNum | read-only | current | This is the Point Data Number of the Profile. This will vary depending on the Point Mode |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.6 | ColumnpfProfileAcquireModeNum | read-only | current | This is the Acquire Mode of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.7 | ColumnpfProfileAcquireDataNum | read-only | current | This is the Acquire Data Number of the Profile. This will vary depending on the Acquire Mode |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.8 | ColumnpfProfileTrackModeNum | read-only | current | This is the Track Mode of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.9 | ColumnpfProfileTrackDataNum | read-only | current | This is the Acquire Data Number of the Profile. This will vary depending on the Track Mode. Always 0? |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.10 | ColumnpfProfileRFNum | read-only | current | This is the RFNum Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.11 | ColumnpfProfileConfigNum | read-only | current | This is the ConfigNum Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.12 | ColumnpfProfilePolModeNum | read-only | current | This is the Pol Mode Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.13 | ColumnpfProfilePolDataNum | read-only | current | This is the Pol Data Number of the Profile. Only used for preset |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.14 | ColumnpfProfilePol2ModeNum | read-only | current | This is the Pol2 Mode Number of the Profile. |
| 1.3.6.1.4.1.1414.1.1.3.5.20.1.15 | ColumnpfProfilePol2DataNum | read-only | current | This is the Pol2 Data Number of the Profile. Only used for preset |
| 1.3.6.1.4.1.1414.1.1.3.6 | NodeacuMountModel | |||
| 1.3.6.1.4.1.1414.1.1.3.6.1 | ScalarmmCalibrationEnable | read-write | current | Write 1 to enable the Mount Model calibration process. Write 0 to stop it. Reading this object indicates whether Mount Model calibration is currently enabled. |
| 1.3.6.1.4.1.1414.1.1.3.6.2 | ScalarmmCoarseCalEnable | read-write | current | Write 1 to request Mount Model coarse calibration. Write 0 to clear the request. Reading this object indicates whether coarse calibration is currently requeste… |
| 1.3.6.1.4.1.1414.1.1.3.6.3 | ScalarmmFastCalEnable | read-write | current | Write 1 to request Mount Model fast calibration. Write 0 to clear the request. Reading this object indicates whether fast calibration is currently requested. |
| 1.3.6.1.4.1.1414.1.1.3.6.4 | ScalarmmFineCalEnable | read-write | current | Write 1 to request Mount Model fine calibration. Write 0 to clear the request. Reading this object indicates whether fine calibration is currently requested. |
| 1.3.6.1.4.1.1414.1.1.3.6.5 | ScalarmmPassReady | read-only | current | This indicates whether the Mount Model subsystem has determined that a selected satellite pass is ready to be used. |
| 1.3.6.1.4.1.1414.1.1.3.6.6 | ScalarmmPreviewCommand | read-write | current | Write 1 to request that the Mount Model subsystem calculate the future target preview list and estimated completion time. Reading this object indicates whether… |
| 1.3.6.1.4.1.1414.1.1.3.6.7 | ScalarmmCleanCommand | read-write | current | Write 1 to request that the Mount Model PassPoint cache be cleared. Reading this object indicates whether the clean request bit is currently asserted. |
| 1.3.6.1.4.1.1414.1.1.3.6.8 | ScalarmmCalibrationState | read-only | current | This is a summarized Mount Model calibration state derived from the active Mount Model control bits. If none of the phase bits are set, the state is idle. |
| 1.3.6.1.4.1.1414.1.1.3.6.9 | ScalarmmNonOrtho | read-write | current | This is the current Mount Model non-orthogonality correction in degrees. This object may also be written to restore a known-good Mount Model solution after a f… |
| 1.3.6.1.4.1.1414.1.1.3.6.10 | ScalarmmNSTilt | read-write | current | This is the current Mount Model north-south tilt correction in degrees. This object may also be written to restore a known-good Mount Model solution after a fa… |
| 1.3.6.1.4.1.1414.1.1.3.6.11 | ScalarmmPolarAlign | read-write | current | This is the current Mount Model polar alignment correction in degrees. This object may also be written to restore a known-good Mount Model solution after a fac… |
| 1.3.6.1.4.1.1414.1.1.3.6.12 | ScalarmmFeedOffset | read-write | current | This is the current Mount Model feed offset correction in degrees. This object may also be written to restore a known-good Mount Model solution after a factory… |
| 1.3.6.1.4.1.1414.1.1.3.6.13 | ScalarmmXEncOffset | read-write | current | This is the current Mount Model X encoder alignment correction in degrees. This object may also be written to restore a known-good Mount Model solution after a… |
| 1.3.6.1.4.1.1414.1.1.3.6.14 | ScalarmmYEncOffset | read-write | current | This is the current Mount Model Y encoder alignment correction in degrees. This object may also be written to restore a known-good Mount Model solution after a… |
| 1.3.6.1.4.1.1414.1.1.3.6.15 | ScalarmmModelError | read-only | current | This is the current Mount Model solution error expressed as a percentage of beamwidth. |
| 1.3.6.1.4.1.1414.1.1.3.6.16 | ScalarmmNumPoints | read-only | current | This is the number of pass points currently used by the Mount Model solution. |
| 1.3.6.1.4.1.1414.1.1.3.6.17 | ScalarmmEstimatedCompletion | read-only | current | This is the estimated Mount Model completion time. The format is hh:mm:ss:ddd:yyyy. |
| 1.3.6.1.4.1.1414.1.1.3.6.18 | TablemmFutureTargetsTable | not-accessible | current | This table contains the currently predicted future target list for Mount Model calibration. |
| 1.3.6.1.4.1.1414.1.1.3.6.18.1 | RowmmFutureTargetsTableData | not-accessible | current | This contains the field descriptions for each Mount Model future target entry. |
| 1.3.6.1.4.1.1414.1.1.3.6.18.1.1 | ColumnmmFutureTargetIndex | read-only | current | This is the index of the Mount Model future target list. |
| 1.3.6.1.4.1.1414.1.1.3.6.18.1.2 | ColumnmmFutureTargetSatNum | read-only | current | This is the satellite number of the predicted future Mount Model calibration target for this table entry. A value of 0 indicates no target is currently populat… |
| 1.3.6.1.4.1.1414.1.1.3.7 | NodeacuBlockzone | |||
| 1.3.6.1.4.1.1414.1.1.3.7.1 | ScalarbzMasterEnable | read-write | current | Write 1 to enable blockzone processing for all configured blockzones. Write 0 to disable all blockzone processing. Reading this object indicates whether blockz… |
| 1.3.6.1.4.1.1414.1.1.3.7.2 | ScalarbzClearCommand | read-write | current | Write 1 to clear the configured blockzone table. Write 0 to leave the current blockzone table unchanged. Reading this object indicates whether the clear reques… |
| 1.3.6.1.4.1.1414.1.1.3.7.3 | ScalarbzPosLimit | read-only | current | This indicates whether the current antenna position is within an active blockzone limit. |
| 1.3.6.1.4.1.1414.1.1.3.7.4 | ScalarbzCmdLimit | read-only | current | This indicates whether the current command path is requesting motion into an active blockzone limit. |
| 1.3.6.1.4.1.1414.1.1.3.7.5 | ScalarbzActiveProcedure | read-only | current | This is the currently active blockzone handling procedure derived from the blockzone status bits. If no blockzone action is active, this object returns none(0). |
| 1.3.6.1.4.1.1414.1.1.3.7.6 | TablebzTable | not-accessible | current | This table contains the configured blockzone definitions. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1 | RowbzTableData | not-accessible | current | This contains the field descriptions for each configured blockzone entry. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.1 | ColumnbzIndex | read-only | current | This is the blockzone table index. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.2 | ColumnbzEnable | read-write | current | Write 1 to enable this blockzone entry. Write 0 to disable this blockzone entry. Reading this object indicates whether the blockzone entry is currently enabled. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.3 | ColumnbzProcedure | read-write | current | This is the configured procedure for the blockzone entry. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.4 | ColumnbzAzCWLimit | read-write | current | This is the clockwise azimuth limit of the blockzone entry in degrees. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.5 | ColumnbzAzCCWLimit | read-write | current | This is the counter-clockwise azimuth limit of the blockzone entry in degrees. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.6 | ColumnbzElTopLimit | read-write | current | This is the top elevation limit of the blockzone entry in degrees. |
| 1.3.6.1.4.1.1414.1.1.3.7.6.1.7 | ColumnbzActive | read-only | current | This indicates whether the blockzone entry is currently active in the blockzone status bits. |