LJ3530mfp-MIB
879 objects
No module-level DESCRIPTION found.
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11 | Nodehp | |||
| 1.3.6.1.4.1.11.2.3.9.4.2 | Nodedm | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1 | Nodedevice | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1 | Nodedevice-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1 | Nodesettings-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1 | Scalarenergy-star | read-write | optional | Returns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 | Scalarsleep-mode | read-write | optional | Returns eTrue if the device is in energy saving sleep mode, otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes the device to wake up, if it is in sl… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.22 | Scalardate-display | read-write | optional | Controls front-panel date display format. Additional information: Controls front-panel date display format. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 | Scalarmono-color-switching-mode | read-write | optional | This object allows the user to view/change the color/mono switching mode for a device. Additional information: This object allows the user to view/change the c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 | Nodedevice-configure | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32.12 | Scalardevice-configure-printer-parameters | read-write | optional | Allow the printer to be configured as a duplex or simplex printer. There will be a <<hidden>> encoded in this string and decoded by the printer firmware. If th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.34 | Scalarcolor-supply-out-action | read-write | optional | This PML object can be used to change the behavior of the printer when a Color Cartridge reaches OUT. When this PML Object is set to eStop, the printer will be… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.43 | Scalardirect-connect-ports-enable | read-write | optional | This object specifies whether all direct connect ports (parallel and USB) are available or ignored. JetDirect, embedded network connectivity, and third party a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.44 | Scalarcontrol-panel-supplies-status-message | read-write | optional | This PML object can be used to enable or disable supplies status messages from being displayed on the control panel. eShow - show the status messages on the co… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.74 | Scalaroverride-a4-with-letter | read-write | optional | This command allows printing on LETTER size paper when an A4 job is sent, but no A4 size paper is loaded. Conversely, this command also allows printing on A4 p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.75 | Scalarremote-upgrade-version-checking-enable | read-write | mandatory | Enables the ability to consume incoming engine RFU jobs without performing an upgrade when the firmware version number specified in the RFU header matches the … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2 | Nodestatus-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.5 | Scalaron-off-line | read-write | optional | To bring the PDL processing sub-system on or off line. If the device is a printer, then the printer does not process print job data when the printer is off lin… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.6 | Scalarcontinue | write-only | optional | A device can support a class of errors called continuable errors. When a continuable error is encountered, the device requires a continue event to occur before… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.7 | Scalarauto-continue | read-write | optional | Indicates if the device will automatically continue after encountering a continuable error. If AUTO-CONTINUE is set to eOn, the device will automatically gener… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.8 | Scalarinstall-date | read-write | optional | Identifies the date that the device was installed. The format of the string is 'YYYYMMDDHHmmZ'. Where: YYYY is the year. MM is the month (1-12). DD is the day … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.10 | Scalarperm-store-init-occurred | read-only | optional | This object will set the cAllPermDevices bit when a full perm storage initialization occurs (as would be the case for a brand new device-system or as a result … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.17 | Scalardate-and-time | read-write | optional | A C structure containing the following fields: typedef struct { ubyte yr; /* year: 0 to 99 */ ubyte mon; /* month: 1 to 12 */ ubyte day; /* day: 1 to 31 */ uby… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.19 | Scalarservice-id | read-write | optional | A read of this object will return the current SERVICE ID value in the printer. The format is 'YYDDD' where: YY = calendar year - 1990 DDD = (calendar month - 1… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20 | Nodedisplay | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1 | Nodedisplay-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1.3 | Scalarshow-address | read-write | optional | If this object is set to eAuto, and the device has an IP address, the IP address of the device will be shown with the READY message. If this object is set to e… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.28 | Scalartime-display | read-write | optional | Controls front-panel time display format. Set to eTimeDisplayTwelveHour for AM/PM display. Set to eTimeDisplayTwentyFourHour for military-type display. Additio… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.35 | Scalarjob-input-auto-continue-timeout | read-write | optional | The number of seconds the device waits after a job related continuable error occurs before automatically continuing. An example job related continuable error i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.36 | Scalarjob-input-auto-continue-mode | read-write | optional | Returns or sets the device behavior when the desired media is not currently available. cCancelJob - The device cancels the job. The device POS should explain w… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37 | Nodebackground-message | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1 | Nodebackground-message1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1.1 | Scalarbackground-status-msg-line1-part1 | read-write | optional | The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2 | Nodebackground-message2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2.1 | Scalarbackground-status-msg-line2-part1 | read-write | optional | The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.3 | Nodebackground-message3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.3.1 | Scalarbackground-status-msg-line3-part1 | read-write | optional | The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.4 | Nodebackground-message4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.4.1 | Scalarbackground-status-msg-line4-part1 | read-write | optional | The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.5 | Scalarbackground-status-msg-higher-priority | read-write | optional | The string displayed on the device's front panel in place of the printer's built-in background status string. It would alternate with warning messages and woul… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.38 | Scalarerror-log-clear | write-only | optional | Setting this object clears all the entries in the error log sub-tree. Additional information: Setting this object removes all errors that have been stored in t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.40 | Scalarjob-output-auto-continue-timeout | read-write | optional | Returns or sets the time that the printer will wait after an output bin becomes full and the printer is trying to deliver a sheet of media to that output bin. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.42 | Scalarcollated-originals-support | read-only | optional | Indicates that the printer can create multiple, collated 'originals' of a job and shows the level of support for this capability. cCollatedOriginals - The prin… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.52 | Scalarlocalization-languages-supported | read-only | optional | The list of languages supported by the device. The languages are primarily, but not limited to, two character codes from ISO 639, each separated by a comma cha… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.53 | Scalarlocalization-countries-supported | read-only | optional | The list of countries supported by the device. The countries are primarily, but not limited to, two character codes from ISO 3166, each separated by a comma ch… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.59 | Scalarhost-application-available-memory | read-only | optional | Returns the amount of memory, in bytes, that the device has available for job-related processing or resources. Also known as driver work space (DWS) memory. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.60 | Scalarcontrol-panel-button-press | write-only | optional | Writing this object simulates pressing a button on the control panel. Reading it will return the last key pressed either on the control panel or via PML. The d… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.63 | Scalarcontrol-panel-display-contents-change-counter | read-only | optional | A counter which increments whenever the contents of the front panel display changes. This object is implemented as a 32-bit signed integer which rolls over to … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.64 | Scalarcontrol-panel-display-contents-crc | read-only | optional | Reading this object returns a 32-bit Cyclical Redundancy Check (CRC) which represents the current contents of the display. Additional information: This object … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.65 | Nodecontrol-panel-display | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.65.1 | Scalarcontrol-panel-display-graphical-contents | read-only | optional | Reading this object returns a graphical file format image representing the current pixel content of the display. The device POS will specify the expected scree… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.66 | Scalarcontrol-panel-key-press | read-write | optional | Writing this object simulates pressing a key on the control panel. Reading it will return the last key pressed either on the control panel or via PML. This obj… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.72 | Scalarpage-frame-memory-available | read-only | optional | Returns the abount of page-frame memory in bytes available in the device-system. Additional information: Total amount of onboard pageframe memory, in kilobytes… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.97 | Scalarship-cartridge-installed-in-printer | read-write | optional | Set developer motor cams in the position needed for shipping the cartridges installed in the printer if set to eTrue. Additional information: Set developer mot… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.99 | Scalarrtc-time-zone | read-write | optional | Controls the time zone, which can be chosen from a list of time zones similar to the one used by Microsoft Windows operating system: eTzDateline -12:00 Interna… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.100 | Scalarautomatic-daylight-savings | read-write | optional | Determines whether or not the automatic adjustment for daylight savings time is enabled. If it's enabled the device local time will be automatically adjusted f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.101 | Scalardaylight-savings-start | read-write | optional | A C structure containing the following fields: typedef struct { ubyte hour; /* hour: 0 to 23 */ ubyte weekday; /* weekday: 0(Sunday) to 6 */ ubyte occurrence; … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.102 | Scalardaylight-savings-end | read-write | optional | A C structure containing the following fields: typedef struct { ubyte hour; /* hour: 0 to 23 */ ubyte weekday; /* weekday: 0(Sunday) to 6 */ ubyte occurrence; … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.103 | Scalardaylight-savings-offset | read-write | optional | Controls the offset in minutes to be added to the time when DST is in effect. Additional information: Controls the offset in minutes to be added to the time wh… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.104 | Scalardaylight-savings-reset | read-write | optional | This object is used to reset (set back to factory default for the current time zone) or read the current status of the DST settings. When Set to eResetToDefaul… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3 | Nodeid | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.1 | Scalarmodel-number | read-only | optional | Identifies the device model number as listed in the HP corporate price list (e.g. C2121A for DeskJet 500C). The string is as specific as possible. Products sho… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.2 | Scalarmodel-name | read-only | optional | Identifies the device model name (e.g. ''DeskJet 1200C''). The string is as specific as possible. Capitalization and spacing should match family naming convent… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.3 | Scalarserial-number | read-only | optional | Identifies the serial number for the device. If the SERIAL-NUMBER object is set by the user, then setting the object does not need to be protected. If the SERI… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.5 | Scalarfw-rom-datecode | read-only | optional | Identifies the base device-system firmware date code. The date code will be encoded in the yyyymmdd format. There may be several versions of the base device-sy… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.6 | Scalarfw-rom-revision | read-only | optional | This identifies the device-system code firmware ROM revision code. The format for a revision is major_revision.minor_revision. There may be other ROM revision … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.10 | Scalardevice-name | read-write | optional | User defined device name. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.11 | Scalardevice-location | read-write | optional | User defined device location. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as muc… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.12 | Scalarasset-number | read-write | optional | User defined asset number. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.20 | Scalarformatter-serial-number | read-only | optional | This object returns the formatter serial number for the device. The value returned from this object is the FORMATTERNUMBER device-system variable. If possible,… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4 | Nodeinterface | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1 | Nodesimm | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1 | Nodesimm1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.4 | Scalarsimm1-type | read-only | optional | Returns an indication of the type of option installed in SIMM slot 1. eEmpty means the device did not detect any option installed in the interface slot. eUnkno… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.5 | Scalarsimm1-capacity | read-only | optional | Returns an indication of the capacity of the SIMM installed in SIMM slot 1. The capacity is dependent on the type of option, as indicated by the SIMM1-TYPE obj… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6 | Nodesimm1-bank | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1 | Nodesimm1-bank1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1.1 | Scalarsimm1-bank1-type | read-only | optional | Returns an indication of the type of option installed in Bank 1 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1.2 | Scalarsimm1-bank1-capacity | read-only | optional | Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2 | Nodesimm1-bank2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2.1 | Scalarsimm1-bank2-type | read-only | optional | Returns an indication of the type of option installed in Bank 2 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2.2 | Scalarsimm1-bank2-capacity | read-only | optional | Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2 | Nodesimm2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.4 | Scalarsimm2-type | read-only | optional | Returns an indication of the type of option installed in SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describ… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.5 | Scalarsimm2-capacity | read-only | optional | Returns an indication of the capacity of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: This object is used f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6 | Nodesimm2-bank | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1 | Nodesimm2-bank1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1.1 | Scalarsimm2-bank1-type | read-only | optional | Returns an indication of the type of option installed in Bank 1 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1.2 | Scalarsimm2-bank1-capacity | read-only | optional | Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2 | Nodesimm2-bank2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2.1 | Scalarsimm2-bank2-type | read-only | optional | Returns an indication of the type of option installed in Bank 2 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2.2 | Scalarsimm2-bank2-capacity | read-only | optional | Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3 | Nodemio | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1 | Nodemio1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.2 | Scalarmio1-model-name | read-only | optional | Returns product information identifying the I/O card. Example: XXXX. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.3 | Scalarmio1-manufacturing-info | read-only | optional | Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 1. May include serial number and firmware revision. Additional informa… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.4 | Scalarmio1-type | read-only | optional | Returns an indication of the type of option installed in MIO/EIO slot 1. See SIMM1-TYPE for an explanation of the enumerations. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.4 | Nodemio4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.4.2 | Scalarmio4-model-name | read-only | optional | Returns product information identifying the I/O card. Example: XXXX. Additional information: Returns a string describing the firmware version of the embedded J… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.4.3 | Scalarmio4-manufacturing-info | read-only | optional | Returns information describing the manufacture of the I/O card installed in MIO/EIO interface 4. May include serial number and firmware revision. Additional in… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.4.4 | Scalarmio4-type | read-only | optional | Returns an indication of the type of option installed in MIO/EIO interface 4. See SIMM1-TYPE for an explanation of the enumerations. Additional information: Re… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.6 | Nodeweb-server | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.6.1 | Nodesettings-web-server | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.6.1.5 | Scalarews-request-control-panel-supplies-status | read-write | optional | System variable EWS_REQUEST_CONTROL_PANEL_SUPPPLIES_STATUS requires a PML interface so that WJA can directly access it without needing EWS support for that. Ad… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9 | Nodeusb-interface | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.1 | Scalarusb-host-supported | read-only | optional | The USB Host protocol is supported by the device when the value returned is eTrue. The USB Host protocol is not supported when the value returned is eFalse. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2 | Nodeusb | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.1 | Scalarusb-serial-number | read-only | optional | Returns the serial number of a connected USB device as defined in the Standard Device Descriptor of the Universal Serial Bus Specification Version 2.0. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.2 | Scalarusb-manufacturer-name | read-only | optional | Returns the description of the manufacturer of a connected USB device as defined in the Standard Device Descriptor of the Universal Serial Bus Specification Ve… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.3 | Scalarusb-product-description | read-only | optional | Returns the product description of a connected USB device as defined in the Standard Device Descriptor of the Universal Serial Bus Specification Version 2.0. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.4 | Scalarusb-vendor-id | read-only | optional | Returns the Vendor ID of a connected USB device as defined in the Standard Device Descriptor of the Universal Serial Bus Specification Version 2.0. The value w… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.5 | Scalarusb-product-id | read-only | optional | Returns the Product ID of a connected USB device as defined in the Standard Device Descriptor of the Universal Serial Bus Specification Version 2.0. The value … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.6 | Scalarusb-device-kind | read-only | optional | The USB-DEVICE-KIND object classifies a USB device into one of four broad categories: \ eUSBStorageDevice(1): The USB device is strictly a device for storing d… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.9.2.7 | Scalarusb-driver-name | read-only | optional | Returns the name of the low-level USB driver supporting this device. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5 | Nodetest | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.2 | Scalarprint-internal-page | read-write | optional | Writing this object to a value other than eNotPrintingAnInternalPage causes the device to attempt to print an internally generated page. Reading this object pr… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.7 | Scalarengine-self-diagnostic | read-only | optional | The ENGINE-SELF-DIAGNOSTIC object reveals current engine failures; it returns a binary string of two-byte motor, clutch, solenoid, and sensor failure codes. Ad… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.8 | Scalarengine-parameter | read-only | optional | The ENGINE-PARAMETER object returns a device specific set of engine parameters as a binary string of byte values. It will be necessary to have a decoder for ea… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6 | Nodejob | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1 | Nodesettings-job | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.1 | Scalarclearable-warning | read-write | optional | Returns or controls how the device will track clearable warnings. A clearable warning indicates a transient event in the device. The device will continue after… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.2 | Scalarcancel-job | write-only | optional | Cancels the print job whose ID matches the value written to the CANCEL-JOB object. The host first learns the job ID using the CURRENT-JOB-PARSING-ID command. I… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.3 | Scalarjob-info-change-id | read-only | optional | Returns the current value of an object in the job-info sub-tree whose value has changed. Define the object identifier for the object whose value has changed as… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.10 | Scalarhold-job-timeout | read-write | optional | The time, in minutes, that the printer will wait before automatically deleting a held job. This allows the printer to automatically clean up jobs that have bee… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2 | Nodeactive-print-jobs | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1 | Nodejob-being-parsed | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1.1 | Scalarcurrent-job-parsing-id | read-only | optional | Contains the printer assigned job identification for the job currently being processed by the processing PDL sub-system. The job ID is a monotonically increasi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3 | Nodefax-job-control | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3 | Nodefaxjob | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.1 | Nodefaxjob-rx-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.1.2 | Scalarfaxjob-rx-count | read-write | optional | This object tracks the number of completed fax jobs received. It counts jobs not individual pages. Counter will increment by one for each job received, no matt… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.3 | Nodefaxjob-tx-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.3.2 | Scalarfaxjob-tx-count | read-write | optional | This object tracks the number of completed fax jobs sent. It counts jobs not individual pages. Counter will increment by one for each job sent, no matter t he … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5 | Nodejob-info | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.1 | Scalarjob-info-name1 | read-only | optional | Contains the first part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: The job name is the s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.2 | Scalarjob-info-name2 | read-only | optional | Contains the second part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: See job-info-name1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.10 | Scalarjob-info-stage | read-only | optional | Indicates what printer sub-systems are currently processing this print job. The last OID field for this dynamic object contains the job ID. cSourceSubsystem - … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.11 | Scalarjob-info-io-source | read-only | optional | Indicates which I/O source, the print job was received over. The value maps to port numbering scheme supported in the DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.12 | Scalarjob-info-pages-processed | read-only | optional | Indicates the number of pages processed by the processing subsystem. If neither the cSourceSubsystem or the cProcessingSubsystem items are in the associated JO… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.13 | Scalarjob-info-pages-printed | read-only | optional | Indicates the number of pages printed by the destination subsystem. If none of the cSourceSubsystem, cProcessingSubsystem or cDestinationSubsystem items are in… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.14 | Scalarjob-info-size | read-only | optional | Indicates the number of bytes of data processed by the processing subsystem. If neither of the cSourceSubsystem or cProcessingSubsystem items are in the associ… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.15 | Scalarjob-info-state | read-only | optional | Indicates the state of the job. The last OID field for this dynamic object contains the job ID. eAborted - the print job was aborted. eWaitingForResources - th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.19 | Scalarjob-info-outcome | read-only | optional | Indicates if any warning or error conditions were encountered while processing the assoicated job. The last OID field for this dynamic object contains the job … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.20 | Scalarjob-info-outbins-used | read-only | optional | Indicates which output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: Th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.22 | Scalarjob-info-physical-outbins-used | read-only | optional | Indicates which physical output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional inform… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23 | Nodejob-info-attribute | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.1 | Scalarjob-info-attr-1 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. Attribute objects are saved sequentially, starting with 1, after the start of a job. If mor… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.2 | Scalarjob-info-attr-2 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.3 | Scalarjob-info-attr-3 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.4 | Scalarjob-info-attr-4 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.5 | Scalarjob-info-attr-5 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.6 | Scalarjob-info-attr-6 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.7 | Scalarjob-info-attr-7 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.8 | Scalarjob-info-attr-8 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.9 | Scalarjob-info-attr-9 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.10 | Scalarjob-info-attr-10 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.11 | Scalarjob-info-attr-11 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.12 | Scalarjob-info-attr-12 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.13 | Scalarjob-info-attr-13 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.14 | Scalarjob-info-attr-14 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.15 | Scalarjob-info-attr-15 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.16 | Scalarjob-info-attr-16 | read-only | optional | Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.24 | Scalarjob-info-requested-originals | read-only | optional | The number of requested collated copies. The value was supplied with the job via PJL QTY variable, the PostScript Collate and NumCopies entries in the page dev… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.25 | Scalarjob-info-page-count-current-original | read-only | optional | The page number being printed within the current copy of a collated multi-copy job. This value changes when the job-info-pages-printed changes. The job-info-pa… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.26 | Scalarjob-info-pages-in-original | read-only | optional | Number of pages in a single copy of a collated multi-copy job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.27 | Scalarjob-info-printed-originals | read-only | optional | Number of collated copies completely printed and delivered to the output bin at time of query. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28 | Nodejob-info-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.1 | Scalarjob-info-accounting-media-size | read-only | optional | Contains the media size of the printed job. The media size of the first page will decide the media size of the entire job. The return value of this object will… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.2 | Scalarjob-info-accounting-media-type | read-only | optional | Contains the media type of the printed job. The media type of the first page will decide the media type of the entire job. The return value of this object will… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.3 | Scalarjob-info-accounting-finishing-options | read-only | optional | Contains the finishing option used on the printed job. The finishing option specified for the first page will decide the finishing option of the entire job. Th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.4 | Scalarjob-info-accounting-media-simplex-count | read-only | optional | Contains the total number of simplex pages printed in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.5 | Scalarjob-info-accounting-media-duplex-count | read-only | optional | Contains the total number of duplex pages printed in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.6 | Scalarjob-info-accounting-grayscale-impression-count | read-only | optional | Contains the total number of monochrome pages printed in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.7 | Scalarjob-info-accounting-color-impression-count | read-only | optional | Contains the total number of color pages printed in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.8 | Scalarjob-info-accounting-black-dots | read-only | optional | Contains the total number of black pixels used in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.9 | Scalarjob-info-accounting-yellow-dots | read-only | optional | Contains the total number of yellow pixels used in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.10 | Scalarjob-info-accounting-cyan-dots | read-only | optional | Contains the total number of cyan pixels used in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.11 | Scalarjob-info-accounting-magenta-dots | read-only | optional | Contains the total number of magenta pixels used in a particular job. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.12 | Scalarjob-info-accounting-scanned-media-simplex-count | read-only | optional | Contains the total number of simplex pages scanned, indexed by media size. For each media size that is scanned, there are 6 bytes of information in the followi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.13 | Scalarjob-info-accounting-scanned-media-duplex-count | read-only | optional | Contains the total number of duplex pages scanned, indexed by media size. For each media size that is scanned, there are 6 bytes of information in the followin… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.14 | Scalarjob-info-accounting-job-type | read-only | optional | Keeps track of what type of job is processed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.32 | Scalarjob-info-accounting-color-usage-log | write-only | optional | Provides applications with the ability to clear or print the Color Usage Log. eClear - clear the log. ePrint - print the log. Either action will complete befor… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7 | Nodeheld-job | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1 | Nodeheld-job-info | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.1 | Scalarheld-job-user-name | read-only | optional | User name that is obtained by the driver through some internal method or from user input. Additional information: The following is a general description for al… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.2 | Scalarheld-job-job-name | read-only | optional | The job name may be generated by the driver or obtained from user input. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.3 | Scalarheld-job-retention | read-only | optional | Indicates the retention classification of the job. The values indicate whether the job is printed immediately or stored. There are 4 options: eHoldOff: The job… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.4 | Scalarheld-job-security | read-only | optional | The variable specifies the security level of the job. eHoldTypePublic: The job does not require a PIN in order to release the job for printing. eHoldTypePrivat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.5 | Scalarheld-job-quantity | read-only | optional | Number of copies to print. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.6 | Scalarheld-job-pin | read-only | optional | A string that is specified in the job stream and then required to be entered in order to release the job for printing. PIN stands for Personal Identification N… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2 | Nodeheld-job-control | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.1 | Scalarheld-job-print | write-only | optional | Instructs the printer to schedule the specified held job for printing with the specified number of copies. The job-id is used to identify which job to print. A… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.2 | Scalarheld-job-delete | write-only | optional | Instructs the printer to delete the specified held job from the list. The job-id is used to identify which job to delete. A held job can also be deleted from t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.3 | Scalarheld-job-set-queue-size | read-write | optional | Sets the maximum number of jobs which can be stored in the held job list. Additional information: Sets the size of the temporary job lists queue. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.4 | Scalarheld-job-enable | read-write | optional | Enables or disables Job Retention (Job Hold). The valid values are eDisabled and eEnabled. (Specifying an invalid mode causes an <badValue> error to be returne… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10 | Nodefile-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1 | Nodesettings-file-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.2 | Scalarfile-system-max-open-files | read-only | optional | The number of open files allowed at one time. Opening a file when the maximum number of files are currently open will fail. Additional information: Indicates t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.6 | Scalarfile-system-set-system-partition-writeable | write-only | optional | This object allows the device-system partition to be written to. It consists of a C structure containing the following fields: typedef struct { ubyte <<hidden>… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.7 | Scalarfile-system-set-system-partition-readonly | write-only | optional | Changes a device-system partition to be READ-ONLY. The value is the volume number to change. If the volume number specified is NOT a device-system partition an… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.8 | Scalarfile-system-delete-files | write-only | optional | Setting this object causes the specified filename to be deleted, after first validating that the authentication data is correct for the specified user ID. The … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3 | Nodefile-systems | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2 | Nodefile-system2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2.6 | Scalarfile-system2-initialize-volume | write-only | optional | Setting this object to eInitializing causes file device-system 2 to be initialized. Reading this object indicates if the file device-system is currently being … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3 | Nodefile-system3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3.6 | Scalarfile-system3-initialize-volume | write-only | optional | Setting this object to eInitializing causes file device-system 3 to be initialized. Reading this object indicates if the file device-system is currently being … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4 | Nodefile-system4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4.6 | Scalarfile-system4-initialize-volume | write-only | optional | Setting this object to eInitializing causes file device-system 4 to be initialized. Reading this object indicates if the file device-system is currently being … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11 | Nodeerrorlog | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1 | Nodeerror1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.1 | Scalarerror1-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 1 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.2 | Scalarerror1-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.3 | Scalarerror1-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2 | Nodeerror2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.1 | Scalarerror2-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 2 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.2 | Scalarerror2-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.3 | Scalarerror2-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3 | Nodeerror3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.1 | Scalarerror3-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 3 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.2 | Scalarerror3-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.3 | Scalarerror3-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4 | Nodeerror4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.1 | Scalarerror4-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 4 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.2 | Scalarerror4-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.3 | Scalarerror4-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5 | Nodeerror5 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.1 | Scalarerror5-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 5 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.2 | Scalarerror5-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.3 | Scalarerror5-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6 | Nodeerror6 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.1 | Scalarerror6-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 6 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.2 | Scalarerror6-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.3 | Scalarerror6-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7 | Nodeerror7 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.1 | Scalarerror7-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 7 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.2 | Scalarerror7-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.3 | Scalarerror7-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8 | Nodeerror8 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.1 | Scalarerror8-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 8 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.2 | Scalarerror8-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.3 | Scalarerror8-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9 | Nodeerror9 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.1 | Scalarerror9-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 9 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.2 | Scalarerror9-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.3 | Scalarerror9-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10 | Nodeerror10 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.1 | Scalarerror10-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 10 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.2 | Scalarerror10-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.3 | Scalarerror10-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11 | Nodeerror11 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.1 | Scalarerror11-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 11 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.2 | Scalarerror11-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.3 | Scalarerror11-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12 | Nodeerror12 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.1 | Scalarerror12-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 12 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.2 | Scalarerror12-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.3 | Scalarerror12-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13 | Nodeerror13 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.1 | Scalarerror13-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 13 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.2 | Scalarerror13-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.3 | Scalarerror13-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14 | Nodeerror14 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.1 | Scalarerror14-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 14 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.2 | Scalarerror14-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.3 | Scalarerror14-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15 | Nodeerror15 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.1 | Scalarerror15-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 15 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.2 | Scalarerror15-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.3 | Scalarerror15-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16 | Nodeerror16 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.1 | Scalarerror16-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 16 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.2 | Scalarerror16-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.3 | Scalarerror16-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17 | Nodeerror17 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.1 | Scalarerror17-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 17 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.2 | Scalarerror17-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.3 | Scalarerror17-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18 | Nodeerror18 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.1 | Scalarerror18-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 18 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.2 | Scalarerror18-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.3 | Scalarerror18-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19 | Nodeerror19 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.1 | Scalarerror19-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 19 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.2 | Scalarerror19-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.3 | Scalarerror19-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20 | Nodeerror20 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.1 | Scalarerror20-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 20 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.2 | Scalarerror20-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.3 | Scalarerror20-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21 | Nodeerror21 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.1 | Scalarerror21-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 21 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.2 | Scalarerror21-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.3 | Scalarerror21-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22 | Nodeerror22 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.1 | Scalarerror22-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 22 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.2 | Scalarerror22-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.3 | Scalarerror22-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23 | Nodeerror23 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.1 | Scalarerror23-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 23 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.2 | Scalarerror23-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.3 | Scalarerror23-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24 | Nodeerror24 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.1 | Scalarerror24-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 24 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.2 | Scalarerror24-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.3 | Scalarerror24-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25 | Nodeerror25 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.1 | Scalarerror25-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 25 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.2 | Scalarerror25-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.3 | Scalarerror25-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26 | Nodeerror26 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.1 | Scalarerror26-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 26 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.2 | Scalarerror26-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.3 | Scalarerror26-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27 | Nodeerror27 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.1 | Scalarerror27-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 27 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.2 | Scalarerror27-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.3 | Scalarerror27-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28 | Nodeerror28 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.1 | Scalarerror28-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 28 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.2 | Scalarerror28-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.3 | Scalarerror28-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29 | Nodeerror29 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.1 | Scalarerror29-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 29 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.2 | Scalarerror29-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.3 | Scalarerror29-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30 | Nodeerror30 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.1 | Scalarerror30-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 30 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.2 | Scalarerror30-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.3 | Scalarerror30-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31 | Nodeerror31 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.1 | Scalarerror31-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 31 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.2 | Scalarerror31-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.3 | Scalarerror31-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32 | Nodeerror32 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.1 | Scalarerror32-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 32 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.2 | Scalarerror32-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.3 | Scalarerror32-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33 | Nodeerror33 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.1 | Scalarerror33-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 33 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.2 | Scalarerror33-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.3 | Scalarerror33-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34 | Nodeerror34 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.1 | Scalarerror34-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 34 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.2 | Scalarerror34-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.3 | Scalarerror34-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35 | Nodeerror35 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.1 | Scalarerror35-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 35 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.2 | Scalarerror35-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.3 | Scalarerror35-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36 | Nodeerror36 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.1 | Scalarerror36-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 36 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.2 | Scalarerror36-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.3 | Scalarerror36-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37 | Nodeerror37 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.1 | Scalarerror37-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 37 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.2 | Scalarerror37-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.3 | Scalarerror37-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38 | Nodeerror38 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.1 | Scalarerror38-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 38 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.2 | Scalarerror38-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.3 | Scalarerror38-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39 | Nodeerror39 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.1 | Scalarerror39-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 39 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.2 | Scalarerror39-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.3 | Scalarerror39-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40 | Nodeerror40 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.1 | Scalarerror40-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 40 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.2 | Scalarerror40-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.3 | Scalarerror40-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41 | Nodeerror41 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.1 | Scalarerror41-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 41 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.2 | Scalarerror41-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.3 | Scalarerror41-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42 | Nodeerror42 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.1 | Scalarerror42-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 42 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.2 | Scalarerror42-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.3 | Scalarerror42-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43 | Nodeerror43 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.1 | Scalarerror43-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 43 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.2 | Scalarerror43-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.3 | Scalarerror43-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44 | Nodeerror44 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.1 | Scalarerror44-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 44 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.2 | Scalarerror44-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.3 | Scalarerror44-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45 | Nodeerror45 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.1 | Scalarerror45-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 45 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.2 | Scalarerror45-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.3 | Scalarerror45-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46 | Nodeerror46 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.1 | Scalarerror46-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 46 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.2 | Scalarerror46-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.3 | Scalarerror46-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47 | Nodeerror47 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.1 | Scalarerror47-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 47 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.2 | Scalarerror47-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.3 | Scalarerror47-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48 | Nodeerror48 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.1 | Scalarerror48-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 48 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.2 | Scalarerror48-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.3 | Scalarerror48-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49 | Nodeerror49 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.1 | Scalarerror49-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 49 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.2 | Scalarerror49-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.3 | Scalarerror49-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50 | Nodeerror50 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.1 | Scalarerror50-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 50 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.2 | Scalarerror50-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.3 | Scalarerror50-date-time | read-only | optional | This item contains the date and the time at which an error occurred. The values returned will be in hexadecimal. If the date is 2004-Jul-13 and the time is 03:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12 | Noderesource-manager | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3 | Nodemass-storage-resources | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.1 | Scalarmass-storage-resource-change-counter | read-only | optional | A counter which changes when a mass storage based resource has been added or deleted. Additional information: The value of this counter changes each time the M… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.2 | Scalarmass-storage-resource-changed | write-only | optional | Setting to eTrue causes MASS-STORAGE-RESOURCE-CHANGE-COUNTER to be incremented. Additional information: Returns <noSuchName> status if attempting to access thi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13 | Noderemote-procedure-call | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1 | Nodesettings-rpc | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1.2 | Scalarrpc-bind-protocol-address | read-only | optional | Array of Berkeley sockets style protocol addresses used to bind RPC to a communications protocol family. Setting an instance of this array object to a zero len… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2 | Nodestatus-rpc | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2.3 | Scalarrpc-bound-protocol-address | read-only | optional | An array of Berkeley sockets style protocol addresses that the NFS service has been bound to successful. The format is that same as the array of RPC-BIND-PROTO… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15 | Nodemass-storage-block-driver | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1 | Nodesettings-mass-storage-bd | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1.1 | Scalarram-disk-mode | read-write | optional | Returns or controls RAM disk support. eOFF turns off the RAM disk functionality. eOn turns on the RAM disk functionality and creates a RAM disk whose size is c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1.2 | Scalarram-disk-size | read-only | optional | Returns or controls the size of the RAM disk. The device POS specifies the minimum memory requirements. The object MAXIMUM-RAM-DISK-MEMORY specifies the maximu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2 | Nodestatus-mass-storage-bd | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2.1 | Scalarmaximum-ram-disk-memory | read-only | optional | This object's name is misleading. This object does not return the maximum configurable RAM disk size. Instead, it returns the maximum amount of memory, in byte… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16 | Nodeaccounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1 | Nodeprinter-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1 | Nodeprinted-media-usage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.1 | Scalarprinted-media-simplex-count | read-only | optional | Total number of simplex pages printed in this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper size… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.2 | Scalarprinted-media-simplex-charge | read-write | optional | Charge for each simplex page printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.3 | Scalarprinted-media-duplex-count | read-only | optional | Total number of duplex pages printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.4 | Scalarprinted-media-duplex-charge | read-write | optional | Charge for each duplex page printed in this media size. Additional information: The click charges for duplex printed media. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.5 | Scalarprinted-media-total-charge | read-only | optional | The total charge for pages printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.6 | Scalarprinted-media-maximum-pixels-per-page | read-only | optional | The number of pixels required to completely fill a page of this media size. The device POS will specify the resolution at which this pixel count was calculated… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.7 | Scalarprinted-media-combined-total | read-only | optional | Total number of letter equivalently weighted pages both color and mono combined with this printer. Additional information: The combined total per page size of … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.10 | Scalarprinted-media-dimplex-count | read-only | optional | Total number of mono dimplex pages printed in this media size. A dimplex page is one that has been printed in duplex mode but the back side is blank. Dimplex p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.2 | Scalarusage-printer-total-charge | read-only | optional | Total printer charge for all paper sizes printed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.4 | Scalarusage-staple-count | read-only | optional | Total number of staples used. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.5 | Scalarusage-instructions-line1 | read-write | optional | The first line of usage instructions for the device user.Appears on Line 1 of the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.6 | Scalarusage-instructions-line2 | read-write | optional | The second line of usage instructions for the device user.Appears on Line 1 of the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.7 | Scalarusage-instructions-line3 | read-write | optional | The third line of usage instructions for the device user.Appears on Line 1 of the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.8 | Scalarusage-instructions-line4 | read-write | optional | The fourth line of usage instructions for the device user.Appears on Line 1 of the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.9 | Scalarprinted-modes-usage-total | read-only | optional | This object reports the total color and mono print modes usage for the life of the printer. This value is reported on the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.10 | Scalarsource-tray-usage-total | read-only | optional | This object reports the total source tray usage for the life of the printer. This value is reported on the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.11 | Scalardestination-bin-usage-total | read-only | optional | This object reports the total destination bin usage for the life of the printer. This value is reported on the usage page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.12 | Scalarusage-printer-mono-total-charge | read-only | optional | Total printer charge for all paper sizes printed in monochrome only. Additional information: This is the total charge over the range of all supported media siz… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.13 | Scalarusage-printer-color-total-charge | read-only | optional | Total printer charge for all paper sizes printed in color only. Additional information: This is the total charge over the range of all supported media sizes fo… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2 | Nodescanner-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1 | Nodescanned-media-usage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.1 | Scalarscanned-media-simplex-count | read-only | optional | Total number of simplex pages scanned, for this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper si… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.2 | Scalarscanned-media-simplex-charge | read-write | optional | Charge for each simplex page printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.3 | Scalarscanned-media-duplex-count | read-only | optional | Total number of duplex pages scanned, for this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.4 | Scalarscanned-media-duplex-charge | read-write | optional | Charge for each duplex page scanned, for this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.5 | Scalarscanned-media-total-charge | read-only | optional | The total charge for pages scanned, for this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.2 | Scalarusage-scanner-total-charge | read-only | optional | Total scanner charge or cost for all paper sizes scanned. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3 | Nodeprinter-color-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1 | Nodeprinted-media-color-usage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.1 | Scalarprinted-media-color-simplex-count | read-only | optional | Total number of color simplex pages printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.3 | Scalarprinted-media-color-duplex-count | read-only | optional | Total number of color duplex pages printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.5 | Scalarprinted-media-color-total-count | read-only | optional | The total count for color pages printed in this media size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.6 | Scalarprinted-media-color-dimplex-count | read-only | optional | Total number of color dimplex pages printed in this media size. A color dimplex page is a color page that has been printed in duplex mode but the back side is … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4 | Nodeprinted-modes-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1 | Nodeprinted-modes-usage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1.1 | Scalarprinted-modes-mono-count | read-only | optional | Total number of mono pages printed in this fuser mode. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1.3 | Scalarprinted-modes-color-count | read-only | optional | Total number of color pages printed in this fuser mode. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1.5 | Scalarprinted-modes-total-count | read-only | optional | The total count for pages printed in this fuser mode. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.5 | Nodesource-tray-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.5.1 | Nodesource-tray-usage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.5.1.1 | Scalarsource-tray-usage-count | read-only | optional | Total number of pages printed from this source tray. Additional information: This object will track how many images have been printed with the original source … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.6 | Nodedestination-bin-accounting | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.6.1 | Nodedestination-bin-usage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.6.1.1 | Scalardestination-bin-usage-count | read-only | optional | Total number of pages printed to this destination bin. Additional information: This object will track how many images have been printed with the original desti… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18 | Nodefirmware-download | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.1 | Scalarfirmware-download-write-status-supported | read-only | optional | This object provides information on whether the printer has the ability to communicate the write-status of the firmware download while the download is taking p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.2 | Scalarfirmware-download-write-time | read-only | optional | If the design of the firmware-download implementation does not allow PML interaction during the download process, this value provides an estimation of the time… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.4 | Scalarfirmware-download-current-state | read-only | optional | Provides the current or last reportable state of the firmware download process. The current state may not necessarily be the current state, but could be the po… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.6 | Scalarfirmware-download-name | read-only | mandatory | This returns the name of the printer. This should match the name in the header of the upgrade image being sent to the flash part. If the name does not match wi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.7 | Scalarfirmware-download-version | read-only | mandatory | This object will return a string value representing the current revision of firmware that the printer is operating with. This is used to determine if code need… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.19 | Nodeoperating-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.19.1 | Scalaros-execute-file | write-only | optional | This object's input is a null-terminated string representing a fully-qualified path name for an executable file. This object causes the file to be executed by … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20 | Nodeupgradable-devices | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.1 | Scalarupgradable-devices-write-status-supported | read-only | optional | This object provides information on whether the upgradable device has the ability to communicate the write-status of the upgrade while the upgrade is taking pl… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.2 | Scalarupgradable-devices-write-time | read-only | optional | If the design of the device upgrade implementation does not allow PML interaction during the download process, this value provides an estimation of the time wh… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.4 | Scalarupgradable-devices-current-state | read-only | optional | Provides the current or last reportable state of the device upgrade process. The current state may not necessarily be the current state, but could be the post-… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.6 | Scalarupgradable-devices-name | read-only | mandatory | This returns the name of the upgradable device. This should match the name in the header of the upgrade image being sent to the flash part. If the name does no… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.7 | Scalarupgradable-devices-version | read-only | mandatory | This object will return a string value representing the current revision of firmware that device X is operating with. This is used to determine if code needs t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.8 | Scalarremote-upgrade-enable | read-write | mandatory | Enables or disables the ability to upgrade the firmware associated with any device that is available to be upgraded. This will be set to on or off at the RFU l… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.10 | Scalarupgradeable-devices-generic-name | read-only | mandatory | This object returns the generic component name of the printer and the upgradable devices. Instead of returning unique model names, this object will return name… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2 | Nodesource-subsystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1 | Nodeio | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1 | Nodesettings-io | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.1 | Scalario-timeout | read-write | optional | The amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel tha… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.2 | Scalario-switch | read-only | optional | Indicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3 | Nodeports | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1 | Nodeport1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.4 | Scalarport1-parallel-speed | read-write | optional | Returns or changes the maximum parallel I/O port speed, for port 1. This object is only supported if this port is a parallel port. An eSlow setting causes a 10… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.5 | Scalarport1-parallel-bidirectionality | read-write | optional | Returns or changes whether the parallel I/O port supports bidirectional communication for port 1. This object is only supported if this port is a parallel port… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2 | Nodescanner | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1 | Nodesettings-scanner | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.15 | Scalarscan-sharpening-coefficient | read-write | optional | Sets the sharpening coefficient used in scanning and image processing. If the device does not support the given value, then it will select the nearest supporte… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.20 | Scalarscanner-accessory-adf-sheet-count | read-only | optional | Total number of sheets that have been fed through the Automatic Document Feed (ADF) accessory. Additional information: The Automatic Document Feed (ADF) count … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.21 | Scalarscanner-accessory-flatbed-scan-count | read-only | optional | Total number of scans performed by a flatbed scanner accessory. Additional information: The count is only incremented when a sheet is scanned on the FLATBED. T… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.59 | Scalarscanner-accessory-adf-one-sided-sheet-count | read-only | optional | This item is incremented by 1 for each sheet that is scanned through the ADF in 1-sided scan mode. Additional information: The value will be updated at the end… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.60 | Scalarscanner-accessory-adf-two-sided-sheet-count | read-only | optional | This item is incremented by 2 for each sheet that is scanned through the ADF in 2-sided scan mode. Additional information: The value will be updated at the end… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.61 | Scalarscanner-accessory-copy-job-scan-count | read-only | optional | This relates to the number of pages scanned for copying. This item is incremented by 2 for each sheet scanned through the ADF in 2-sided scan mode, and it is i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.62 | Scalarscanner-accessory-send-job-scan-count | read-only | optional | This relates to the number of pages scanned for fax/send. This item is incremented by 2 for each sheet scanned through the ADF in 2-sided scan mode, and it is … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.63 | Scalarscanner-accessory-total-copy-pages-printed | read-only | optional | This relates to the number of copy pages printed on a device. The output sheet that is duplexed (made 2- sided) should be counted as 2 pages. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.64 | Scalarscanner-accessory-digital-send-module-url | read-only | optional | This item sets the URL pointer to the Digital Send Module that is servicing this accessory. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.65 | Scalarscanner-accessory-digital-send-status | read-only | optional | This item is used for detecting the status of the Digital Send component. A bit-mask indicates the status as follows: 0x00 = READY 0x01 = DIGITAL_SEND_GATEWAY_… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.66 | Scalardefault-scan-original-size | read-write | optional | Contains the default size of the original to be scanned. Additional information: Contains the default size of the original to be scanned. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.67 | Scalardefault-scan-text-graphics-mix | read-write | optional | Contains the mix between graphics and text on the scanned page. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.68 | Scalardefault-scan-job-mode | read-write | optional | Allows user to continue scanning more pages. The UI will prompt user for more pages if job mode is on. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.69 | Scalardefault-scan-background-removal | read-write | optional | Background level for background removal. Additional information: Background level for background removal. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.70 | Scalardefault-scan-image-quality | read-write | optional | Select default image quality. Additional information: Which image quality to use. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.71 | Scalardefault-scan-content-orientation | read-write | optional | Contains the default content orientation for a scanned document. Additional information: Contains the default content orientation for a scanned document, i.e.,… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.78 | Scalarauto-send-reset | read-write | optional | Enables (1) or disables (0) the auto resend timeout. Additional information: Enables (2) or disables (1) the DEFAULT-RESET-SEND-TIMEOUT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.79 | Scalarscanner-accessory-digital-send-log-event-counter | read-only | optional | Incremented each time the digital sender writes a log entry. Additional information: Trappable object that is incremented each time the digital sender writes a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.80 | Scalarscanner-accessory-digital-send-config-email-gateway | read-only | optional | Contains the email gateway address. Additional information: Contains the email gateway address. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.81 | Scalarscanner-accessory-digital-send-config-ldap-gateway | read-only | optional | Contains the LDAP gateway address. Additional information: Contains the ldap gateway address. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.82 | Scalarscanner-accessory-digital-send-config-dsm-enabled-fax | read-only | optional | Indicates if the digital fax service is available. Additional information: Indicates if digital fax service is available. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.83 | Scalarscanner-accessory-digital-send-config-fax-embedded | read-only | optional | Indicates if the analog fax device is available. Additional information: Indicates if the analog fax (Belin) is available. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.88 | Scalardefault-scanner-speed | read-write | optional | Determines the default scanner speed. (1) is 25 ppm and (2) is 50 ppm. Additional information: Determines the default scanner speed. (1) is e25 and (2) is e50. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.89 | Scalarscan-to-folder-count | read-only | optional | The number of scan-to-folder scan jobs. Additional information: The number of scan-to-folder scan jobs. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.90 | Scalarfax-job-scan-count | read-only | optional | The number of fax scan jobs. Additional information: The number of fax scan jobs. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.91 | Scalarscanner-accessory-digital-send-home-screen-status | read-only | optional | Returns a bitmap of enabled, configured, and responding DS services that indicate what items are present on the Home Screen. Additional information: Returns a … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2 | Nodestatus-scanner | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.1 | Scalarnot-ready-source-scanner | read-only | optional | Indicates whether and why the scanner is not ready. A set bit indicates a problem. Additional information: This object gives a description of why the scanner i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.5 | Scalarscan-calibration-download | read-write | optional | |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.6 | Scalarscan-calibration-error | read-only | optional | Error status of the most recent calibration session. eNoError(1) - The calibation was successful. eUnknownCalibrationError(2) - An unknown error occurred. eSca… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.4 | Nodespooler | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1 | Nodesettings-spooler | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1.1 | Scalarmopy-mode | read-write | optional | Controls or reports how mopies are generated. eOff turns off the mopy feature. eAuto allows the device to determine the best method for generating mopies based… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3 | Nodeprocessing-subsystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3 | Nodepdl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1 | Nodesettings-pdl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.4 | Scalardefault-copies | read-write | optional | Returns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.5 | Scalarform-feed | write-only | optional | Instructs the PDL processing sub-system to finishing processing the current page of the current job. Form feed is also known as close page or eject page. If th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.8 | Scalardefault-vertical-black-resolution | read-write | optional | Returns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In $product_str changing this OID a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.9 | Scalardefault-horizontal-black-resolution | read-write | optional | Returns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In $product_str changing this obj… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.11 | Scalardefault-lines-per-page | read-write | optional | Returns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest sup… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.12 | Scalardefault-vmi | read-write | optional | Returns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupport… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.13 | Scalardefault-media-size | read-write | optional | This indicates the default media size. A write of an unsupported value causes an <ErrorInvalidOrUnsupported Value>. Complete list of supported media sizes alon… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.19 | Scalarcold-reset-media-size | read-write | optional | Returns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.22 | Scalardefault-media-name | read-write | optional | Returns or sets the media name that is used until the media name is changed by a print job command. Additional information: Returns or sets the media name that… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.36 | Scalarreprint | read-write | optional | Returns or changes the reprint (jam recovery) setting. If eOn, then the device will reprint pages jammed pages. If eOff, the device will not attempt to reprint… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2 | Nodestatus-pdl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2.2 | Scalarform-feed-needed | read-only | optional | Indicates if the PDL processing sub-system has made marks on the current page and the source subsystem has been idle for a device specific amount of time. Addi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3 | Nodepdl-pcl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.5 | Scalarpcl-total-page-count | read-only | optional | Total number of PCL pages printed by the device. Additional information: In $product_str the PCL page count is kept in NVRAM, and the NVRAM value is updated at… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.13 | Scalarpcl-default-font-height | read-write | optional | Returns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.14 | Scalarpcl-default-font-source | read-write | optional | Returns or changes the value of the default font source variable in NVRAM. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.15 | Scalarpcl-default-font-number | read-write | optional | Returns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an <badValue>. Additiona… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.16 | Scalarpcl-default-font-width | read-write | optional | Returns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4 | Nodepdl-postscript | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.5 | Scalarpostscript-total-page-count | read-only | optional | Total number of PostScript pages printed by the device. Additional information: This object is only supported if the PostScript option is installed. In $produc… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.11 | Scalarpostscript-print-errors | read-write | optional | Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.14 | Scalarpostscript-defer-media | read-write | optional | This object will be used to enable or disable the use of the Adobe Postscript Paper Handling Model in the printer firmware. By default it is enabled which mean… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.5 | Nodepjl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7 | Nodefax-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1 | Nodesettings-fax-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.39 | Scalarfax-number-confirmation | read-write | mandatory | The object is used to control the Fax Number Confirmation feature. Additional information: The object is used to control the Fax Number Confirmation feature. e… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2 | Nodestatus-fax-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.11 | Scalarafax-send-page-count | read-write | optional | Keeps the total number of pages sent successfully via the analog fax modem. This count would be synchronised with the number of fax jobs sent successfully. The… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.12 | Scalarafax-recv-page-count | read-write | optional | Keeps the total number of pages received successfully via the analog fax modem. This count would be synchronised with the number of fax jobs received successfu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.9 | Nodewebserver-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.9.1 | Nodesettings-webserver | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.9.1.2 | Scalarweb-server-url | read-write | optional | A Universal Resource Locator (URL) from which the Embedded Web Server can be configured. Any limitation on the size of this URL will be specified in the device… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.9.1.3 | Scalarweb-server-security | read-write | optional | Each collection bit represents a device or Embedded Web Server feature that can be enabled or disabled via this object. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4 | Nodedestination-subsystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1 | Nodeprint-engine | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1 | Nodesettings-prt-eng | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.2 | Scalaroverride-media-name | read-write | optional | Sets a string identifying the media name that is to be used in place of the currently requested media. The substitution will continue until another media is se… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.3 | Scalaroverride-media-size | read-write | optional | Sets the media size that is to be used in place of the currently requested media size. Additional information: When a request is received to print on a size an… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9 | Nodemarking-agent-density | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.2 | Scalarmarking-agent-highlights-density-setting | read-write | optional | Returns or sets the marking agent highlights density setting for each of the marking agents installed. The value of this object is in the range of -5..+5. The … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.3 | Scalarmarking-agent-midtones-density-setting | read-write | optional | Returns or sets the marking agent midtones density setting for each of the marking agents installed. The value of this object is in the range of -5..+5. See MA… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.4 | Scalarmarking-agent-shadows-density-setting | read-write | optional | Returns or sets the marking agent shadows density setting for each of the marking agents installed. The value of this object is in the range of -5..+5. See MAR… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.11 | Scalarautocleaning-page-frequency | read-write | optional | Controls the number of pages between printing of the auto cleaning page (if enabled). Any device specific 'snap' behavior for this page interval will be specif… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.12 | Scalarautocleaning-page-size | read-write | optional | Controls the size of paper used to print the auto cleaning page (if enabled). Additional information: Controls the size of paper used to print the auto cleanin… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.14 | Scalardefault-audible-feedback | read-write | optional | Returns or sets the audible feedback function. The default value will be documented in the device POS. Additional information: Turns the audible feedback funct… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.15 | Scalardefault-reset-send-timeout | read-write | optional | Returns or sets the period of time, specified in milliseconds, to wait before the digital send settings are reset to default values. The default will be specif… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.16 | Scalardefault-authentication-timeout | read-write | optional | Returns or sets the period of time, specified in milliseconds, to wait before an authentication becomes invalid. The default will be specified in the device PO… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.17 | Scalardefault-staple-mode | read-write | optional | Returns or sets the default staple mode. The device POS will specify the default and supported values. Additional information: Selects staple mode. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.24 | Scalarconfigurable-low-threshold-setting | read-write | optional | This PML object can be used to configure the low threshold for supplies. Additional information: This PML object can be used to configure the Low Threshold for… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.25 | Scalarsupplies-replace-action-at-setting | read-write | optional | This object can be used to change the setting of menu item REPLACE SUPPLIES. The behavior of the printer when a supply reaches low changes in accordance with t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.26 | Scalarsupply-out-user-configured-override-limit | read-only | optional | This PML object reports the user configured cartridge out override page limit. Additional information: This PML object reports the user configured cartridge ou… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.27 | Scalarcartridge-out-override-control | write-only | optional | This PML object is used to control Cartridge Out Override feature. Additional information: This object is used for the following purposes: 1. Enable/disable ca… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.28 | Scalarduplex-blank-pages | read-write | optional | When the value of the device-system variable is set to eDuplexBlankPagesAuto, it means to Smart Duplex in any of the specified conditions. This selection is lo… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.31 | Scalarfinisher-image-rotation | read-write | optional | This PML object will provide the additional image rotation that is applied to a printed job depending on the presence or absence of a finisher device or the va… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.33 | Scalarsupply-out-user-configured-override2-limit | read-only | optional | This PML object reports the user configured consumable out override level two page limit. Additional information: This PML object reports the user configured c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.34 | Scalaritb-tensioning-status | read-only | optional | This object is uses to determine the Current status of the ITB. It will either be De-Tensioned or Tenstioned and it will return an enumeration accordingly. If … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.36 | Scalarcartridge-adaptive-gain | read-only | optional | The Adaptive TA Gain is stored for the last 5 cartridges. Cartridge one is the most recent to be installed (current), and cartridge 5 is least recent to be ins… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.37 | Scalarcartridge-adaptive-gain-reset | write-only | optional | This object will Reset the Adaptive TA Gain value to 1.00 and disable the adaptive TA routine. The value that this object returns is stored in non-volatile mem… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2 | Nodestatus-prt-eng | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.7 | Scalartotal-color-page-count | read-only | optional | Total number of color pages printed by the device. Additional information: Total number of color pages printed by the device. The valid range of this object is… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.22 | Scalarduplex-page-count | read-only | optional | Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not mark… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.26 | Scalarprint-engine-revision | read-only | optional | Print engine revision string. Additional information: Print engine revision string. The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37 | Nodeprinter-calibration-dhalf | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.1 | Scalarprinter-cal-dhalf-page-count | read-only | optional | Provides the page count when the last DHALF calibration occurred. A '-1' indicates that a calibration of this kind has not taken place yet. This object exists … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.2 | Scalarprinter-cal-dhalf-utc | read-only | optional | Provides the time (in UTC - Universal Time Code format) when the last DHALF calibration occurred. This value could be zero if no calibration has taken place or… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.3 | Nodeprinter-cal-dhalf-data | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.3.1 | Scalarprinter-cal-dhalf-data1 | read-only | optional | Provides a device specific set of DHalf calibration data as a binary string of byte values. It will be necessary to have a decoder for each engine to interpret… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.3.2 | Scalarprinter-cal-dhalf-data2 | read-only | optional | Provides a device specific set of DHalf calibration data as a binary string of byte values. It will be necessary to have a decoder for each engine to interpret… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38 | Nodeprinter-calibration-cpr | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38.1 | Scalarprinter-cal-cpr-page-count | read-only | optional | Provides the page count when last CPR calibration occurred. A '-1' indicates that a calibration of this kind has not taken place yet. This object exists (and i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38.2 | Scalarprinter-cal-cpr-utc | read-only | optional | Provides the time (in UTC - Universal Time Code format) when the last CPR calibration occurred. This value could be zero if no calibration has taken place or i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38.3 | Scalarprinter-cal-cpr-data | read-only | optional | Provides a device specific set of CPR calibration data as a binary string of byte values. It will be necessary to have a decoder for each engine to interpret t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.48 | Scalarsupply-out-action-support | read-only | optional | This object is used to determine if a particular capability that allows printing to continue after one or more cartridge has reached out is supported by the de… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.49 | Scalarsupply-out-device-state | read-only | optional | This PML object indicates the current behavior of the device if one or more supplies have reached out. If no supply has reached out, the value of this PML obje… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.50 | Scalarsupply-after-out-state | read-only | optional | This object is used to read and write the various status flags indicating whether the consumable was used after out. The collection bits supported include: cNo… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.52 | Scalarprinter-cal-customiq-factory-default | read-only | optional | Provides the status of the customIQ color table, indicating whether the table is the factory default or whether the table has been updated via RFU. eFactoryDef… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3 | Nodeintray | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1 | Nodesettings-intray | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.2 | Scalarinput-tray-auto-select | read-write | optional | Indicates if the device will automatically try to load media from the next input media tray in the auto-select sequence (defined by each device) when it cannot… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.8 | Scalarcustom-paper-feed-dim | read-write | optional | Sets the printer's custom paper dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.9 | Scalarcustom-paper-xfeed-dim | read-write | optional | Sets the printer's custom paper dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.10 | Scalardefault-custom-paper-dim-unit | read-write | optional | The units of measure used to specify the width and height of the printer's default custom paper size. The unit of measure of eTenThousandthsOfInches is 0.0001 … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.11 | Scalardefault-custom-paper-feed-dim | read-write | optional | Sets the printer's default custom paper size dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.12 | Scalardefault-custom-paper-xfeed-dim | read-write | optional | Sets the printer's default custom paper size dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The v… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.14 | Scalarinput-tray-max-media-feed-dim | read-only | optional | The maximum physical media size in the feed direction of this input device expressed in units of measure specified by INPUT- TRAY-MIN-MAX-DIM-UNIT. A value of … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.15 | Scalarinput-tray-max-media-xfeed-dim | read-only | optional | The maximum physical media size across the feed direction of a particular input device expressed in units of measure specified by INPUT-TRAY-MIN-MAX-DIM-UNIT. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.16 | Scalarinput-tray-min-media-feed-dim | read-only | optional | The minimum physical media size in the feed direction of a particular input device expressed in units of measure specified by PrtInputMinMaxDimUnit. A value of… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.17 | Scalarinput-tray-min-media-xfeed-dim | read-only | optional | The minimum physical media size across the feed direction of a particular input device expressed in units of measure specified by PrtInputMinMaxDimUnit. A valu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.19 | Scalartray-prompt | read-write | optional | If this object is set to eDisplay, whenever a paper tray is opened, refilled, and closed in a printer, the end user is prompted with a message 'To change size … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3 | Nodeintrays | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1 | Nodeintray1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.1 | Scalartray1-media-size-loaded | read-write | optional | Returns the media size that is currently configuredconfigured in tray #1. This object can be set to indicate the media size currently loaded, if the printer su… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.12 | Scalartray1-phd | read-only | optional | Provides the number of the Paper Handling Device that contains this input tray. Additional information: Provides the number of the Paper Handling Device that c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2 | Nodeintray2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.1 | Scalartray2-media-size-loaded | read-write | optional | Returns the media size that is currently configured in tray #2. Complete list of supported media sizes along with their dimensions are listed in the ''Media Si… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.12 | Scalartray2-phd | read-only | optional | Provides the number of the Paper Handling Device that contains this input tray. Additional information: Provides the number of the Paper Handling Device that c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3 | Nodeintray3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.1 | Scalartray3-media-size-loaded | read-write | optional | Returns the media size that is currently configured in tray #3. Complete list of supported media sizes along with their dimensions are listed in the ''Media Si… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.12 | Scalartray3-phd | read-only | optional | Provides the number of the Paper Handling Device that contains this input tray. Additional information: Provides the number of the Paper Handling Device that c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4 | Nodeoutbin | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1 | Nodesettings-outbin | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1.4 | Scalaroverflow-bin | read-write | optional | Returns or sets the bin that will be used for additional sheets of media when the current bin is full and printing is allowed to continue. Additional informati… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3 | Nodeoutbins | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1 | Nodeoutbin1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1.9 | Scalaroutbin1-override-mode | read-write | optional | Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5 | Nodemarking-agent | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1 | Nodesettings-marking-agent | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.11 | Scalarmarker-density-calibration | read-write | optional | Returns the calibration status or triggers a calibration cycle. All calibration procedures are used if set to eCalibrateALL. If set to eCalibrateColor then a f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6 | Nodeimaging | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.10 | Scalardefault-mfp-color-space | read-write | optional | Which color space to use � CMY for color, Subtractive Gray for mono. Additional information: Which color space to use- CMY for color, Subtractive Gray for mo… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7 | Nodeph | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.1 | Nodesettings-ph | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.1.1 | Scalartray-disable-use-instead | read-write | optional | If this object is set to eEnabled, the paper mount message that is normally posted('To use another tray....') is turned off thereby disallowing the user to spe… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8 | Nodeprint-media | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1 | Nodesettings-print-media | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.1 | Scalarmedia-names-available | read-write | optional | The value of this object controls which of the MEDIAx-NAME objects are supported. If a bit is set to zero, then attempting to get or set the corresponding MEDI… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.2 | Scalarnorth-edge-offset | read-write | optional | Returns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the m… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3 | Nodemedia-info | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1 | Nodemedia1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.1 | Scalarmedia1-name | read-write | optional | Media 1 name. Additional information: The order of these objects is determined by the order of SysOD_MediaTypeEnum. The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.2 | Scalarmedia1-short-name | read-write | optional | Length restricted version of the media name 1. The length restriction is required to allow the media name to be displayed on the device's control panel. The de… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.3 | Scalarmedia1-page-count | read-only | optional | Number of sheets of media 1 that have been printed. The device POS should state whether this value is lost across a power cycle or kept in NVRAM. Additional in… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.4 | Scalarmedia1-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Display… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2 | Nodemedia2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.1 | Scalarmedia2-name | read-write | optional | Media 2 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.2 | Scalarmedia2-short-name | read-write | optional | Length restricted version of the media name 2. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.3 | Scalarmedia2-page-count | read-only | optional | Number of sheets of media 2 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.4 | Scalarmedia2-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3 | Nodemedia3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.1 | Scalarmedia3-name | read-write | optional | Media 3 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.2 | Scalarmedia3-short-name | read-write | optional | Length restricted version of the media name 3. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.3 | Scalarmedia3-page-count | read-only | optional | Number of sheets of media 3 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.4 | Scalarmedia3-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4 | Nodemedia4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.1 | Scalarmedia4-name | read-write | optional | Media 4 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.2 | Scalarmedia4-short-name | read-write | optional | Length restricted version of the media name 4. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.3 | Scalarmedia4-page-count | read-only | optional | Number of sheets of media 4 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.4 | Scalarmedia4-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5 | Nodemedia5 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.1 | Scalarmedia5-name | read-write | optional | Media 5 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.2 | Scalarmedia5-short-name | read-write | optional | Length restricted version of the media name 5. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.3 | Scalarmedia5-page-count | read-only | optional | Number of sheets of media 5 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.4 | Scalarmedia5-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6 | Nodemedia6 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.1 | Scalarmedia6-name | read-write | optional | Media 6 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.2 | Scalarmedia6-short-name | read-write | optional | Length restricted version of the media name 6. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.3 | Scalarmedia6-page-count | read-only | optional | Number of sheets of media 6 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.4 | Scalarmedia6-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7 | Nodemedia7 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.1 | Scalarmedia7-name | read-write | optional | Media 7 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.2 | Scalarmedia7-short-name | read-write | optional | Length restricted version of the media name 7. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.3 | Scalarmedia7-page-count | read-only | optional | Number of sheets of media 7 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.4 | Scalarmedia7-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8 | Nodemedia8 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.1 | Scalarmedia8-name | read-write | optional | Media 8 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.2 | Scalarmedia8-short-name | read-write | optional | Length restricted version of the media name 8. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.3 | Scalarmedia8-page-count | read-only | optional | Number of sheets of media 8 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.4 | Scalarmedia8-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9 | Nodemedia9 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.1 | Scalarmedia9-name | read-write | optional | Media 9 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.2 | Scalarmedia9-short-name | read-write | optional | Length restricted version of the media name 9. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.3 | Scalarmedia9-page-count | read-only | optional | Number of sheets of media 9 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.4 | Scalarmedia9-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10 | Nodemedia10 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.1 | Scalarmedia10-name | read-write | optional | Media 10 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.2 | Scalarmedia10-short-name | read-write | optional | Length restricted version of the media name 10. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.3 | Scalarmedia10-page-count | read-only | optional | Number of sheets of media 10 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.4 | Scalarmedia10-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11 | Nodemedia11 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.1 | Scalarmedia11-name | read-write | optional | Media 11 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.2 | Scalarmedia11-short-name | read-write | optional | Length restricted version of the media name 11. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.3 | Scalarmedia11-page-count | read-only | optional | Number of sheets of media 11 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.4 | Scalarmedia11-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12 | Nodemedia12 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.1 | Scalarmedia12-name | read-write | optional | Media 12 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.2 | Scalarmedia12-short-name | read-write | optional | Length restricted version of the media name 12. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.3 | Scalarmedia12-page-count | read-only | optional | Number of sheets of media 12 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.4 | Scalarmedia12-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13 | Nodemedia13 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.1 | Scalarmedia13-name | read-write | optional | Media 13 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.2 | Scalarmedia13-short-name | read-write | optional | Length restricted version of the media name 13. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.3 | Scalarmedia13-page-count | read-only | optional | Number of sheets of media 13 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.4 | Scalarmedia13-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14 | Nodemedia14 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.1 | Scalarmedia14-name | read-write | optional | Media 14 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.2 | Scalarmedia14-short-name | read-write | optional | Length restricted version of the media name 14. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.3 | Scalarmedia14-page-count | read-only | optional | Number of sheets of media 14 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.4 | Scalarmedia14-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15 | Nodemedia15 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.1 | Scalarmedia15-name | read-write | optional | Media 15 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.2 | Scalarmedia15-short-name | read-write | optional | Length restricted version of the media name 15. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.3 | Scalarmedia15-page-count | read-only | optional | Number of sheets of media 15 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.4 | Scalarmedia15-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16 | Nodemedia16 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.1 | Scalarmedia16-name | read-write | optional | Media 16 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.2 | Scalarmedia16-short-name | read-write | optional | Length restricted version of the media name 16. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.3 | Scalarmedia16-page-count | read-only | optional | Number of sheets of media 16 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.4 | Scalarmedia16-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17 | Nodemedia17 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.1 | Scalarmedia17-name | read-write | optional | Media 17 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.2 | Scalarmedia17-short-name | read-write | optional | Length restricted version of the media name 17. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.3 | Scalarmedia17-page-count | read-only | optional | Number of sheets of media 17 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.4 | Scalarmedia17-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18 | Nodemedia18 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.1 | Scalarmedia18-name | read-write | optional | Media 18 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.2 | Scalarmedia18-short-name | read-write | optional | Length restricted version of the media name 18. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.3 | Scalarmedia18-page-count | read-only | optional | Number of sheets of media 18 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.4 | Scalarmedia18-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19 | Nodemedia19 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.1 | Scalarmedia19-name | read-write | optional | Media 19 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.2 | Scalarmedia19-short-name | read-write | optional | Length restricted version of the media name 19. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.3 | Scalarmedia19-page-count | read-only | optional | Number of sheets of media 19 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.4 | Scalarmedia19-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20 | Nodemedia20 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.1 | Scalarmedia20-name | read-write | optional | Media 20 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.2 | Scalarmedia20-short-name | read-write | optional | Length restricted version of the media name 20. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.3 | Scalarmedia20-page-count | read-only | optional | Number of sheets of media 20 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.4 | Scalarmedia20-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21 | Nodemedia21 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.1 | Scalarmedia21-name | read-write | optional | Media 21 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.2 | Scalarmedia21-short-name | read-write | optional | Length restricted version of the media name 21. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.3 | Scalarmedia21-page-count | read-only | optional | Number of sheets of media 21 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.4 | Scalarmedia21-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22 | Nodemedia22 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.1 | Scalarmedia22-name | read-write | optional | Media 22 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.2 | Scalarmedia22-short-name | read-write | optional | Length restricted version of the media name 22. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.3 | Scalarmedia22-page-count | read-only | optional | Number of sheets of media 22 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.4 | Scalarmedia22-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23 | Nodemedia23 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23.1 | Scalarmedia23-name | read-write | optional | Media 23 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23.2 | Scalarmedia23-short-name | read-write | optional | Length restricted version of the media name 23. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23.3 | Scalarmedia23-page-count | read-only | optional | Number of sheets of media 23 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23.4 | Scalarmedia23-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24 | Nodemedia24 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24.1 | Scalarmedia24-name | read-write | optional | Media 24 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24.2 | Scalarmedia24-short-name | read-write | optional | Length restricted version of the media name 24. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24.3 | Scalarmedia24-page-count | read-only | optional | Number of sheets of media 24 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24.4 | Scalarmedia24-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.25 | Nodemedia25 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.25.1 | Scalarmedia25-name | read-write | optional | Media 25 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.25.2 | Scalarmedia25-short-name | read-write | optional | Length restricted version of the media name 25. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.25.3 | Scalarmedia25-page-count | read-only | optional | Number of sheets of media 25 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.25.4 | Scalarmedia25-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.26 | Nodemedia26 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.26.1 | Scalarmedia26-name | read-write | optional | Media 26 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.26.2 | Scalarmedia26-short-name | read-write | optional | Length restricted version of the media name 26. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.26.3 | Scalarmedia26-page-count | read-only | optional | Number of sheets of media 26 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.26.4 | Scalarmedia26-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.27 | Nodemedia27 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.27.1 | Scalarmedia27-name | read-write | optional | Media 27 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.27.2 | Scalarmedia27-short-name | read-write | optional | Length restricted version of the media name 27. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.27.3 | Scalarmedia27-page-count | read-only | optional | Number of sheets of media 27 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.27.4 | Scalarmedia27-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.28 | Nodemedia28 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.28.1 | Scalarmedia28-name | read-write | optional | Media 28 name. Additional information: See MEDIA1-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.28.2 | Scalarmedia28-short-name | read-write | optional | Length restricted version of the media name 28. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.28.3 | Scalarmedia28-page-count | read-only | optional | Number of sheets of media 28 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.28.4 | Scalarmedia28-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4 | Nodemedia-modes | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4.1 | Scalarengine-media-modes-supported1 | read-only | optional | The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: 'Normal,Rough,Low,Vellum… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5 | Nodemedia-size | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.1 | Scalarmedia-size-count | read-only | optional | The number of impressions printed on sheets of this media size. The device POS should state whether this value is lost across a power cycle or is kept in perma… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.2 | Scalarmedia-size-west-edge-first-side-offset | read-write | optional | Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.3 | Scalarmedia-size-west-edge-second-side-offset | read-write | optional | Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.4 | Scalarmedia-size-west-edge-side-offset-by-tray | read-write | optional | Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). A positive value move… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.7 | Nodemedia-counts | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.7.1 | Scalarnon-assured-oht-page-count | read-only | optional | This is a count of the number of invalid (non-HP Laser Jet) transparencies that have been printed on. This value is incremented every time an invalid OHT is pr… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.8 | Nodemedia-types | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.8.1 | Scalarmedia-number-of-type-supported | read-only | optional | Indicates the maximum number of supported media types. Additional information: Indicates the number of supported media type. This also indicates which bit in M… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10 | Nodeconsumables | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1 | Nodeconsumables-1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1 | Nodeconsumable-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.56 | Scalarconsumable-status-partnumber | read-only | optional | This object will have one sub-array for the consumable and will will hold the consumable's part number. Additional information: This object is used to report P… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.75 | Scalarconsumable-status-web-service-access-data | read-only | optional | This object is used to report Web Service Access Data. Additional information: This object is used to report Web Service Access Data. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.76 | Scalarconsumable-status-web-service-access-control | read-only | optional | This object is used to report data that controls how web service access is enabled. Additional information: This object is used to report data that controls ho… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.96 | Scalarconsumable-status-tls-max-value | read-only | optional | This object returns the toner level sensor (TLS) max value for the consumable. Additional information: This object returns the TLS max value for the consumable. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.97 | Scalarconsumable-status-printer-design-compatibility | read-only | optional | This object will returns the value of printer design compatibility for the consumable. Additional information: This object will returns the value of printer de… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.99 | Scalarconsumable-status-toner-low-sensing-level | read-only | optional | This object will return the value of toner low sensing level for the consumable. Additional information: This object returns the toner low sensing level for th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.2 | Scalarconsumable-reorder-url | read-write | optional | This object is used to read and write the URL that can be used to reorder consumables for this device. This URL is set at the factory but can be updated by a r… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5 | Nodeconsumables-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1 | Nodeconsumables-life | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.1 | Scalarconsumable-life-usage-units-remaining | read-only | optional | This object reports the current estimate of the number of usage units that remain before this supply is depleted. An installed supply that cannot report such a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.2 | Scalarconsumable-life-usage-units | read-only | optional | This object reports current usage units in use by the corresponding CONSUMABLE-LIFE-USAGE-UNITS-REMAINING object. Additional information: This object returns t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.3 | Scalarconsumable-life-low-threshold | read-only | optional | This object is used to report and modify a threshold value indicating the point in the life of a consumable or supply at which a transition to a LOW state will… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.7 | Scalarconsumable-current-state | read-only | optional | This PML object returns the current state of the particular consumable. cAuthLevel1 - Consumable is at Authentication Level 1 cAuthLevel2 - Consumable is at Au… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.8 | Nodeconsumable-string | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.8.1 | Scalarconsumable-string-information | read-write | optional | This object is used to read and write the string value that describes the consumable information. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.8.2 | Scalarconsumable-string-information-reset | read-write | optional | This object is used to reset (set back to factory default) or read the current status of the corresponding information string. When Set to eResetToDefault, thi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.9 | Scalardevice-used-while-cartridge-out-override-active | read-only | optional | Returns eUsed if the device has ever been used while Cartridge Out Override is activated. Merely enabling cartridge out override will not cause eUsed to be ret… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.10 | Scalarconsumable-notification-status | read-write | optional | This object is used to read and write the various status flags supported by this consumable. For Laserjet 4700 MFP the collection bits supported include: cClie… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.11 | Scalarconsumable-pages-printed-with-supply | read-only | optional | This PML object returns the number of pages printed with a cartridge consumable. This PML object returns the value that should be displayed under 'Pages Printe… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.12 | Scalarsupply-override-activated-level | read-only | optional | This PML object indicates the last override activation level for a given supply. Additional information: This PML object indicates the last override activation… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.13 | Scalarsupply-override-activated-pagecount | read-only | optional | This object reports the printer�s historical page count at which the last override activation occurred for a given supply. Additional information: This objec… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.14 | Scalarsupply-override-activated-date | read-only | optional | This object reports the date when the last override activation occurred for a given supply. Additional information: This object reports the date when the last … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.15 | Scalartotal-kilo-pixels-per-cartridge | read-only | optional | Returns the total number of kilo-pixels at 600dpi in the cartridge. That is, the number returned by this object should be multiplied by 1000 to determine the t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11 | Nodeprint-meter | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1 | Nodeprinter-average | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.4 | Scalarprinter-average-marking-agent-units-per-gram | read-only | optional | This object is used to read the marking agent units of measure per gram. This is typically a conversion factor for converting pixels of toner to grams. This pi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.5 | Scalarprinter-average-marking-agent-coverage-actual | read-only | optional | This object is used to read the actual average marking agent coverage for a given color plane. It is a real number that represents percent coverage and will re… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.13 | Nodemenus | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5 | Nodecopier | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1 | Nodesettings-copier | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.9 | Scalardefault-copier-media-size | read-write | optional | Sets the default copy paper size. The device will scan and format the print data based on the value of this object. The device behavior when the scanned media … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.10 | Scalardefault-copier-image-type | read-write | optional | Specifies the dither matrix used when performing a copy operation. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.14 | Scalarcopier-media-type | read-write | optional | Returns or sets the copier media type. This value is stored in NVRAM, hence the value is saved over power cycles. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.28 | Scalardefault-copy-duplex-mode | read-write | optional | Returns or sets the duplex copying mode. Duplex printing is when printing occurs on both sides of a sheet of media. Long edge binding is also called vertical b… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.29 | Scalardefault-copy-input-tray | read-write | optional | This describes the default input tray to be used. The correspondence between enumerated values and actual trays is device defined (and device dependent). The s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.30 | Scalardefault-copy-output-bin | read-write | optional | This describes the default output bin to be used. The correspondence between enumerated values and actual bins is device defined (and device dependent). The su… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.31 | Scalardefault-copy-reset-timeout | read-write | optional | The time, in seconds, that the printer will wait before automatically reverting to default copy settings. Additional information: This value is saved over a po… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.32 | Scalardefault-copier-quantity | read-write | optional | This item configures the default copy quantity. Additional information: This value is saved over a powercycle. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.33 | Scalardefault-copier-flip-pages-up | read-write | optional | This item configures the default for the copy 'flip-pages-up' status. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.34 | Scalardefault-copier-pages-per-sheet | read-write | optional | Selects a special digital copier mode as follows: eNone: This is the normal copy mode, which means none of the special features are in effect. eTwoUp : Scans i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.35 | Scalardefault-copier-page-borders | read-write | optional | Selects a page boarder mode as follows: eNone : This is the normal copy mode, which no boarder is drawn. eLine : A simple border box is drawn around each scann… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.36 | Scalardefault-copier-collate | read-write | optional | This describes the default setting used to stack the output of a set of copies. eCollate : Copies are stacked 1st page of 1st copy, 2nd page of 1st copy, 3rd p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.37 | Scalardefault-copier-contrast | read-write | optional | This item configures the default Intensity (brightness/contrast) setting. The number of discrete units should be application dependent. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.38 | Scalardefault-copier-edge-to-edge | read-write | optional | This item configures the default edge-to-edge setting for copy jobs. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.39 | Scalarcopy-job-scan-ahead | read-write | optional | When eOn, this implements the 'no-wait scanning' feature. Originals are scanned to disk while waiting for the printer to become available. Default is eOn. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.40 | Scalarcopy-job-auto-interrupt | read-write | optional | When eOn, a walk-up job will automatically interrupt an already-printing mopy jobat a mopy boundary. Default is eOff. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.41 | Scalarcopy-job-interrupt-copy-jobs | read-write | optional | When eOn, this prompts the user whether to interrupt an already-printing copy job when a new copy job is started. Default is eOff. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.42 | Scalarcopy-job-hold-off-print-jobs | read-write | optional | Controls whether new or pending print jobs can begin while a walk-up user is setting up a job. That is, for copy jobs and scan jobs, when eOn this prevents pri… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.43 | Scalarcopy-job-hold-time | read-write | optional | Prevents non-copy print jobs from starting for specified interval after copy job is completely printed. Defined in seconds. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.58 | Scalardefault-copy-job-chromaticity | read-write | optional | Determines the default copy job color setting. eMono(1) is mono and eColor(2) is color. Additional information: Determines the default copy job color setting. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.59 | Scalarfirst-copy-speed | read-write | optional | This describes the warm-up mode used for the first copy eNoEarlyWarmup: With this the fast first copy feature is disabled. eEarlyWarmup: Early warm up is prese… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.67 | Scalarcolor-copy-enabled | read-write | optional | If this object is set to eEnabled, the MFP allows the user to make color copies, else mono copies can only be made. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.68 | Scalarcopy-job-alternative-letterhead-mode | read-write | optional | Configures the MFP to use the Alternative Letterhead Mode when copying to selected media types (letterhead, pre-printed, and user-defined types) to avoid requi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6 | Nodechannel | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.1 | Scalarchannelnumberofchannels | write-only | optional | An indication of how many print data channels the I/O card supports. Additional information: This object is used by the IIO card to tell the peripheral firmwar… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.2 | Scalarchannelprinteralert | read-only | optional | Identifies the values of prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, and prtAlertCode for the latest critical ev… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3 | NodechannelTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1 | NodechannelEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.2 | Scalarchanneltype | write-only | optional | Identifies the type of MIO print data channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.3 | Scalarchannelprotocolversion | write-only | optional | The version of the protocol used on this MIO print data channel. Additional information: After telling the peripheral how many logical channels will be used, t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.4 | Scalarchannelstate | write-only | optional | The state of this print data channel. The value determines whether control information and print data is allowed through this channel or not. Additional inform… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.5 | Scalarchannelifindex | write-only | optional | The value of ifIndex which corresponds to this channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO ca… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.6 | Scalarchannelstatus | write-only | optional | Sub-unit status is reported in the entries of the principle table in the Group that represents the sub-unit. For sub-units that report a status, there is a sta… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.7 | Scalarchannelinformation | write-only | optional | Auxiliary information to allow a printing application to use the channel for data submission to the printer. An application capable of using a specific PrtChan… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7 | Nodetables | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2 | NodedeviceChannelTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1 | NodedeviceChannelEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.2 | Scalarchannel-bytes-sent | read-only | optional | The low order 31 bits of the number of bytes sent from the printer to the host on this logical channel. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.3 | Scalarchannel-bytes-received | read-only | optional | The low order 31 bits of the number of bytes received by the printer from the host on this logical channel. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.4 | Scalarchannel-io-errors | read-only | optional | The low order 31 bits of the number of I/O errors which have occured on this logical channel. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.5 | Scalarchannel-jobs-received | read-only | optional | The low order 31 bits of the number of print jobs which have been received on this logical channel. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.6 | Scalarchannel-mio | read-only | optional | The number of the MIO card associated with this logical channel. If this logical channel is not associated with an MIO card a zero is returned. The value retur… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING |