LJ477-MIB
796 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3 | Nodeorg | |||
| 1.3.6 | Nodedod | |||
| 1.3.6.1 | Nodeinternet | |||
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.11 | NodehpPrintServer | |||
| 1.3.6.1.4.1.11.2 | Nodenm | |||
| 1.3.6.1.4.1.11.2.3.9.4.2 | Nodedm | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1 | Nodedevice | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1 | Nodeiso | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1 | Nodesystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1 | Nodesettings-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1 | Scalarenergy-star | read-only | optional | Returns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 | Scalarsleep-mode | read-only | optional | Returns eTrue if the device is in energy saving sleep mode, otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes the device to wake up, if it is in sl… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.9 | Scalarservice-password | write-only | optional | When set to the password value, other service related objects become 'visible' (i.e readable) and/or become writable. When written with any other value, the se… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.11 | Scalardevice-cfg-download | read-write | optional | Handshaking mechanism between host and device to coordinate the download of device specific data. eCfgDownloadIdle - indicates device configuration download ac… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.12 | Scalardevice-cfg-download-data-type | read-write | optional | Indicates the type of device specific data to be downloaded. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.13 | Scalardevice-cfg-upload | read-write | optional | Handshaking mechanism between host and device to coordinate the upload of device specific data. eCfgUploadIdle - indicates device configuration upload activity… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.14 | Scalardevice-cfg-upload-data-type | read-write | optional | Indicates the type of device specific data to be uploaded. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.17 | Scalardownload-timeout | read-write | optional | Specifies the number of seconds that device will wait for data from the host before the device determines the host is being unresponsive. This timeout conditio… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.18 | Scalarupload-timeout | read-write | optional | Specifies the number of seconds that device will wait for response from the host after transmitting a unit of data before the device determines the host is bei… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.22 | Scalardate-display | read-write | optional | Controls front-panel date display format. Additional information: Controls front-panel date display format. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.23 | Scalardevice-cfg-param-command | read-write | optional | A C structure containing the following fields: typedef struct { u8bit list_id; s8bit auto_incr; u16bit max_index; u16bit rec_size; u16bit index; u8bit data[]; … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.24 | Scalarcopier-token | read-write | optional | Provides an advisory locking mechanism for hosts to coordinate exclusive access to a copier device. Setting the object to a unique id will only succeed if the … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.26 | Scalarfax-upload-token | read-write | optional | Provides an advisory locking mechanism for hosts to coordinate exclusive access to the fax upload features of a device. Setting the object to a unique id will … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.27 | Scalarfax-download-token | read-write | optional | Provides an advisory locking mechanism for hosts to coordinate exclusive access to the fax download features of a device. Setting the object to a unique id wil… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 | Scalarmono-color-switching-mode | read-write | optional | This object allows the user to view/change the color/mono switching mode for a device. Additional information: This object allows the user to view/change the c… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 | Nodedevice-configure | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32.10 | Scalardevice-configure-generic-language-prompt | read-write | optional | This object is used to determine whether to prompt the user to enter the appropriate language. Additional information: This object is used to determine whether… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32.11 | Scalardevice-configure-generic-country-prompt | read-write | optional | This object is used to determine whether to prompt the user to enter the appropriate country at boot. Additional information: This object is used to determine … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2 | Nodestatus-system | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.5 | Scalaron-off-line | read-only | optional | To bring the PDL processing sub-system on or off line. If the device is a printer, then the printer does not process print job data when the printer is off lin… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.7 | Scalarauto-continue | read-write | optional | Indicates if the device will automatically continue after encountering a continuable error. If AUTO-CONTINUE is set to eOn, the device will automatically gener… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.8 | Scalarinstall-date | read-write | optional | Identifies the date that the device was installed. The format of the string is 'YYYYMMDDHHmmZ'. Where: YYYY is the year. MM is the month (1-12). DD is the day … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.17 | Scalardate-and-time | read-write | optional | A C structure containing the following fields: typedef struct { ubyte yr; /* year: 0 to 99 */ ubyte mon; /* month: 1 to 12 */ ubyte day; /* day: 1 to 31 */ uby… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20 | Nodedisplay | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1 | Nodedisplay-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1.3 | Scalarshow-address | read-write | optional | If this object is set to eAuto, and the device has an IP address, the IP address of the device will be shown with the READY message. If this object is set to e… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.28 | Scalartime-display | read-write | optional | Controls front-panel time display format. Set to eTimeDisplayTwelveHour for AM/PM display. Set to eTimeDisplayTwentyFourHour for military-type display. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.35 | Scalarjob-input-auto-continue-timeout | read-write | optional | The number of seconds the device waits after a job related continuable error occurs before automatically continuing. An example job related continuable error i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.36 | Scalarjob-input-auto-continue-mode | read-write | optional | Returns or sets the device behavior when the desired media is not currently available. cCancelJob - The device cancels the job. The device POS should explain w… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.43 | Scalardevice-cfg-download-error | read-only | optional | Error status of the configuration download session. POS should indicate the actual error values reserving value 0 as NO ERROR. Additional information: A value … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.45 | Scalardevice-cfg-upload-error | read-only | optional | Error status of the configuration upload session. POS should indicate the actual error values reserving value 0 as NO ERROR. Additional information: A value of… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.60 | Scalarcontrol-panel-button-press | write-only | optional | Writing this object simulates pressing a button on the control panel. Reading it will return the last key pressed either on the control panel or via PML. The d… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.68 | Scalarclear-nvram | write-only | optional | Writing this object causes the specified NVRAM init option to be performed. Depending on the option, some (or all) of the permanent storage area will be comple… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3 | Nodeid | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.1 | Scalarmodel-number | read-only | optional | Identifies the device model number as listed in the HP corporate price list (e.g. C2121A for DeskJet 500C). The string is as specific as possible. Products sho… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.2 | Scalarmodel-name | read-only | optional | Identifies the device model name (e.g. ''DeskJet 1200C''). The string is as specific as possible. Capitalization and spacing should match family naming convent… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.3 | Scalarserial-number | read-write | optional | Identifies the serial number for the device. If the SERIAL-NUMBER object is set by the user, then setting the object does not need to be protected. If the SERI… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.5 | Scalarfw-rom-datecode | read-only | optional | Identifies the base system firmware date code. The date code will be encoded in the yyyymmdd format. There may be several versions of the base system firmware.… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.8 | Scalarfax-local-phone-num | read-write | optional | CCITT sender's station id (ex. 08-396-4122). |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.9 | Scalarfax-station-name | read-write | optional | name for the fax device (ex. HP R&D). |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.10 | Scalardevice-name | read-write | optional | User defined device name. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.12 | Scalarasset-number | read-write | optional | User defined asset number. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.18 | Scalarfax-line-interface-unit-id | read-only | optional | The fax device line interface unit (LIU) identifier. The LIU number identifies the telephone system electrical characteristics supported by this device. Additi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5 | Nodetest | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.1 | Scalarself-test | read-write | optional | Writing this object allows a device self test to be started. Reading this object provides an indication what self-test is currently executing, if any. Actual s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.2 | Scalarprint-internal-page | read-write | optional | Writing this object to a value other than eNotPrintingAnInternalPage causes the device to attempt to print an internally generated page. Reading this object pr… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6 | Nodejob | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1 | Nodesettings-job | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.2 | Scalarcancel-job | read-write | optional | Cancels the print job whose ID matches the value written to the CANCEL-JOB object. The host first learns the job ID using the CURRENT-JOB-PARSING-ID command. I… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.3 | Scalarjob-info-change-id | read-only | optional | Returns the current value of an object in the job-info sub-tree whose value has changed. Define the object identifier for the object whose value has changed as… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2 | Nodeactive-print-jobs | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1 | Nodejob-being-parsed | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1.1 | Scalarcurrent-job-parsing-id | read-only | optional | Contains the printer assigned job identification for the job currently being processed by the processing PDL sub-system. The job ID is a monotonically increasi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3 | Nodefax-job-control | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.1 | Nodesettings-fax-job | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.1.1 | Scalarfaxjob-action | read-write | optional | Permits host to specify an action to be applied with a particular fax. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.1.2 | Scalarfaxjob-action-id | read-write | optional | Contains the fax job identification of the fax to be acted upon by the action specified by the object FAXJOB-ACTION. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.1.3 | Scalarfaxjob-tx-type | read-write | optional | Indicates sources of the fax image for transmission. Also specifies the temporal order of the data sources. eSrcHostOnly - The fax document images will be whol… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.2 | Nodestatus-fax-job | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.2.1 | Scalarfaxjob-download-id | read-only | optional | Contains the device assigned job identification for the current fax downloading job. The job ID is monotonically increasing number. The job ID may be reset to … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.2.2 | Scalarfaxjob-rx-id | read-only | optional | Contains the device assigned job identification for the currently fax reception job. The job ID is monotonically increasing number. The job ID may be reset to … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.2.3 | Scalarfaxjob-tx-id | read-only | optional | Contains the device assigned job identification for the current fax transmission job. The job ID is monotonically increasing number. The job ID may be reset to… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.2.4 | Scalarfaxjob-upload-id | read-only | optional | Contains the device assigned job identification for the current fax upload job. The job ID is monotonically increasing number. The job ID may be reset to zero … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3 | Nodefaxjob | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.1 | Nodefaxjob-rx-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.1.1 | Scalarfaxjob-rx-status-1 | read-only | optional | Status of receiving fax session 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.3 | Nodefaxjob-tx-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.3.1 | Scalarfaxjob-tx-status-1 | read-only | optional | Status of sending fax session 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.4 | Nodefaxjob-tx-error | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.4.1 | Scalarfaxjob-tx-error-1 | read-only | optional | Error status of the fax reception session 1. Additional information: Error status of the fax transmission session 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.5 | Nodefaxjob-tx-current-page | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.5.1 | Scalarfaxjob-tx-current-page-1 | read-only | optional | The page number of the fax page currently being transmitted via send fax session 1. Starts with page number 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.6 | Nodefaxjob-rx-current-page | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.6.1 | Scalarfaxjob-rx-current-page-1 | read-only | optional | The page number of the fax page currently being received via fax reception session 1. Starts with page number 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.7 | Nodefaxjob-rx-duration | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.7.1 | Scalarfaxjob-rx-duration-1 | read-only | optional | Represent the number of seconds of phone-connect time for a fax reception session 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.8 | Nodefaxjob-tx-duration | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.3.3.8.1 | Scalarfaxjob-tx-duration-1 | read-only | optional | Represent the number of seconds of phone-connect time for send fax session 1. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.4 | Nodefax-activity-log | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.4.1 | Nodesettings-faxlog | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.4.1.1 | Scalarfax-log-action | read-write | optional | Provides applications with the ability to clear or print the fax transaction log. eIdle - no action is occurring on the fax log. eClear - clear the fax log. eP… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.4.1.2 | Scalarfax-log-reporting | read-write | optional | Specifies when fax transaction logs are to be printed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5 | Nodejob-info | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.11 | Scalarjob-info-io-source | read-only | optional | Indicates which I/O source, the print job was received over. The value maps to port numbering scheme supported in the DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.20 | Scalarjob-info-outbins-used | read-only | optional | Indicates which output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: Th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.8 | Nodephoto-job | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.8.2 | Scalarphoto-access-card-error | read-only | optional | Specifies the error reason for most recent unsucessful photo card access. Additional information: Specifies the error reason for most recent unsucessful photo … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9 | NodenetPeripheral | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9 | Nodephone | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1 | Nodedial | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1 | NodenetPrinter | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1 | Nodedial-all-lines | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1 | NodegeneralDeviceStatus | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.1 | Scalarfax-dial-mode | read-write | optional | Device should use DTMF dialing if eToneDial, pulse dial if ePulseDial. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.1 | ScalargdStatusBytes | read-only | current | The number of valid bytes in the gdStatusEntry array. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2 | Scalardevice-redial | read-write | optional | Device to permit redial upon detecting certain error conditions. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2 | NodegdStatusEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.1 | ScalargdStatusLineState | read-only | current | This describes the line state of the peripheral. When non-zero, the peripheral is off-line. When zero the peripheral is on-line. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.2 | ScalargdStatusPaperState | read-only | current | This describes the state of the paper on the peripheral. When non-zero, the peripheral has a paper problem. When zero, the peripheral does not have a paper pro… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.3 | ScalargdStatusInterventionState | read-only | current | This describes the intervention state of the peripheral. When non-zero, the peripheral requires human intervention to continue working. When zero, it requires … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.6 | ScalargdStatusPeripheralError | read-only | current | This is the error code from the peripheral. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.8 | ScalargdStatusPaperOut | read-only | current | This indicates that the peripheral is out of paper. off (0), paper-out-or-paper-mount (1), manual-paper-feed-needed (2) For some peripherals, such as the HP La… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.9 | ScalargdStatusPaperJam | read-only | current | This indicates that the peripheral has a paper jam. off (0), paper-jam(1) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.10 | ScalargdStatusTonerLow | read-only | current | This indicates that the peripheral has a low toner condition. off (0), toner-low (1), no-toner-cartridge (2) For some peripherals, such as the HP LaserJet IIIS… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.11 | ScalargdStatusPagePunt | read-only | current | This indicates that the peripheral did not receive data fast enough to keep up with the print engine when generating a page. For some peripherals, such as the … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.12 | ScalargdStatusMemoryOut | read-only | current | This indicates that the peripheral did not have enough memory to render an image on a page. For some peripherals, such as the HP LaserJet IIISi printer or HP D… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.13 | ScalargdStatusIoActive | read-only | current | This indicates that the peripheral is processing data from this I/O interface card. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.14 | ScalargdStatusBusy | read-only | current | This indicates that the peripheral is busy processing print/plot data. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, thi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.15 | ScalargdStatusWait | read-only | current | This indicates that the peripheral is waiting for print/plot data to process. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plott… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.16 | ScalargdStatusInitialize | read-only | current | This indicates that the peripheral is initializing or warming up. off (0), initializing (1), warm-up(2) For some peripherals, such as the HP LaserJet IIISi pri… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.17 | ScalargdStatusDoorOpen | read-only | current | This indicates that the peripheral cover or door is open. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is al… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.18 | ScalargdStatusPrinting | read-only | current | This indicates that the peripheral is printing or otherwise marking or moving paper. off (0), ordinary-page (1), test-fonts-config-or-start-page (2) For some p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.2.19 | ScalargdStatusPaperOutput | read-only | current | This indicates that the peripheral has a paper output problem such as the output storage bin being full. off (0), output-storage-full (1) For some peripherals,… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.3 | Scalarfax-pulse-dial-support | read-only | optional | This object reports whether the current set country supports pulse dial. Additional information: This object reports whether the current set country supports p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.3 | ScalargdStatusDisplay | read-only | current | The string diplayed on the peripheral front panel. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this is always a zero l… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.7 | ScalargdStatusId | read-only | current | A formatted string of NVT ASCII charactersdescribing this peripheral. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.10 | ScalargdStatusJobTimeout | read-write | obsolete | |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.1.1.13 | ScalargdPasswords | read-write | current | This object is used as a 256 byte NVRAM area for JetAdmin. It is completely managed by JetAdmin. Initially it is initialized to all zeros. A coldboot will re-i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.2 | Nodeanswer | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.2.1 | Nodeanswer-all-lines | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.2.1.1 | Scalarfax-answer-mode | read-write | optional | Sets the answering-priority when using a shared voice line. eManualAnswer - Device will not automatically answer the phone. User must answer and push START but… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.2.1.2 | Scalarfax-num-rings-pickup | read-write | optional | Number of rings before the fax device answers the phone if FAX-ANSWER-MODE is not set to MANUAL-MODE. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.2.1.3 | Scalardevice-ring-type-pickup | read-write | optional | Device to answer the incoming call based on detecting the the specified type of telephone ring. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.4 | NodenetPML | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.4.1 | NodenetPMLtrap | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.4.1.1 | ScalarpmlTrapEnable | read-write | current | This OID is used to enable individual peripheral trappable objects through the print server. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.9.4.1.2 | ScalarpmlTrapDisable | read-write | current | This OID is used to disable individual peripheral trappable objects through the print server. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11 | Nodeerrorlog | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1 | Nodeerror1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.1 | Scalarerror1-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 1 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.2 | Scalarerror1-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2 | Nodeerror2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.1 | Scalarerror2-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 2 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.2 | Scalarerror2-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3 | Nodeerror3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.1 | Scalarerror3-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 3 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.2 | Scalarerror3-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4 | Nodeerror4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.1 | Scalarerror4-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 4 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.2 | Scalarerror4-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5 | Nodeerror5 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.1 | Scalarerror5-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 5 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.2 | Scalarerror5-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6 | Nodeerror6 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.1 | Scalarerror6-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 6 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.2 | Scalarerror6-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7 | Nodeerror7 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.1 | Scalarerror7-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 7 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.2 | Scalarerror7-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8 | Nodeerror8 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.1 | Scalarerror8-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 8 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.2 | Scalarerror8-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9 | Nodeerror9 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.1 | Scalarerror9-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 9 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 197… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.2 | Scalarerror9-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10 | Nodeerror10 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.1 | Scalarerror10-time-stamp | read-only | optional | Contains some sort of time stamp indicating when error 10 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 19… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.2 | Scalarerror10-code | read-only | optional | Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18 | Nodefirmware-download | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.7 | Scalarfirmware-download-version | read-only | optional | This object will return a string value representing the current revision of firmware that the printer is operating with. This is used to determine if code need… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2 | Nodesource-subsystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1 | Nodeio | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1 | Nodesettings-io | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.1 | Scalario-timeout | read-write | optional | The amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel tha… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.2 | Scalario-switch | read-only | optional | Indicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2 | Nodescanner | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1 | Nodesettings-scanner | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.32 | Nodescan-calibration | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.32.18 | Scalarscan-calibration-target | read-only | optional | This object is used by the host to check which type of calibration this scan device supports. The device pos will describe the meaning and intent of each type … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.43 | Scalarscanner-jam-page-count | read-write | optional | Indicates a count of the total pages jammed in the scanner'slifetime. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.44 | Scalarscanner-adf-page-count | read-write | optional | Indicates a count of the total pages scanned through the ADF on the device. This may include scan to host jobs, copyjobs, and fax jobs. If only the total pages… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.45 | Scalarscan-adf-page-count | read-write | optional | Indicates the total pages scanned through the ADF to the host from the device. If the total pages scanned through the scanner are needed for all features, incl… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.48 | Scalarscanner-retrieve-scanline | write-only | optional | This object facilitates the sending of a scan line of data from the scanner to a host. It grabs either raw or corrected data. SERVICE-PASSWORD must be set corr… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.49 | Scalarscanner-motor-control | write-only | optional | This objects is set to the number of steps that the scan motor should move. SERVICE-PASSWORD must be setcorrectly to use this object. Additional information: T… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.51 | Scalarscanner-scanline-statistics | read-only | optional | This object is used to obtain statistics about the scan line that was previously obtained using the SCANNER-RETRIEVE-SCANLINE object. Just as SERVICE-PASSWORD … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.52 | Scalarscan-control-descriptor | read-only | optional | Describes the control language and formats supported for this scanner. Additional information: This string is also used by Jetdirect Embedded WebScan |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.73 | Scalarscan-flatbed-page-count | read-write | optional | This object tracks the page count for the pages scanned from the flatbed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.74 | Scalarscanner-flatbed-page-count | read-write | optional | This object tracks the page count for the pages scanned for all jobs from the flatbed. This includes scan to host jobs, fax jobs, and copy jobs. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.75 | Scalarscanner-modular-hardware | read-only | optional | Used to specify whether optional hardware is installed or not Additional information: This HP LaserJet MFP uses this object to allow a host to query whether or… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.84 | Scalarscanner-clock-edge-modifiers | read-write | optional | This object accesses a table used by firmware to modify clock edge values for CCD scanner modules. Additional information: This object accesses a table used by… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.85 | Scalarscan-clock-edges | read-only | optional | Returns a table of clock edges used by the scanner. Additional information: Returns a table of clock edges used by the scanner. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.86 | Scalarscan-emulate-copy | read-write | optional | Setting this object to eYes will cause firmware to run the next scan job as if it were a copy job, using copy values for scanner h/w and image processing, and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2 | Nodestatus-scanner | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.1 | Scalarnot-ready-source-scanner | read-only | optional | Indicates whether and why the scanner is not ready. A set bit indicates a problem. Additional information: ISSUES: Timberline only used cScannerFeederJam. Tahi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.5 | Scalarscan-calibration-download | read-write | optional | Returns or changes the state of the calibration operation. cScanCalibrationIdle - indicates that calibration is not in progress. cScanCalibrationStart - This s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.6 | Scalarscan-calibration-error | read-only | optional | Error status of the most recent calibration session. eNoError(1) - The calibation was successful. eUnknownCalibrationError(2) - An unknown error occurred. eSca… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.8 | Scalarscanner-lamp-gain-value | read-only | optional | Provides PWM and analog gain for the color channels. The range will vary based on scan mode. The device specific POS should describe the valid range. The forma… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.9 | Scalarscanner-light-monitor-window | read-only | optional | Provides the pixel at which the LMW starts, as the ratio of the average LMW value to the six pixel average value. The device specific pos should specify the va… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.10 | Scalarscanner-reference-position | read-only | optional | Provides 3 pairs of x,y coordinates within a specified range of the calibrate reference position. The device specific POS should specify the valid ranges. The … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.11 | Scalarscanner-sensor-manufacturer | read-only | optional | Reports the scan sensor manufacturer. The device specific POS should list valid manufacturers. Additional information: Reports the scan sensor manufacturer. Th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.2.13 | Scalarcopy-scanner-dimensions | read-only | optional | This object is used to obtain the exact pixel scan dimensions for copy. The dimensions returned correspond to the quality, reduce/enlarge, and media size curre… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.3 | Nodefax-receive | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.3.1 | Nodesettings-fax-receive | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.3.1.1 | Scalarfax-receive-stamping-enable | read-write | optional | Controls whether or not incoming pages of a fax will be stamped upon receipt. Content of the stamp is device-specific but may include such information as date,… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.3.2 | Nodestatus-fax-receive | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.3.2.1 | Scalarnot-ready-fax-receive | read-only | optional | Indicates if the receiving fax sub-system in the device is not ready. If there are no items in the collection (i.e. no bits are set), then the receiving fax su… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3 | Nodeprocessing-subsystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3 | Nodepdl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1 | Nodesettings-pdl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.4 | Scalardefault-copies | read-write | optional | Returns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.8 | Scalardefault-vertical-black-resolution | read-write | optional | Returns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In the product, changing this OID a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.9 | Scalardefault-horizontal-black-resolution | read-write | optional | Returns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In the product, changing this OID… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.11 | Scalardefault-lines-per-page | read-write | optional | Returns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest sup… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.12 | Scalardefault-vmi | read-write | optional | Returns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupport… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.13 | Scalardefault-media-size | read-write | optional | This indicates the default media size. A write of an unsupported value causes an <ErrorInvalidOrUnsupported Value>. Complete list of supported media sizes alon… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.19 | Scalarcold-reset-media-size | read-write | optional | Returns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.22 | Scalardefault-media-name | read-write | optional | Returns or sets the media name that is used until the media name is changed by a print job command. Additional information: This string must be one of the MEDI… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.36 | Scalarreprint | read-write | optional | Returns or changes the reprint (jam recovery) setting. If eOn, then the device will reprint pages jammed pages. If eOff, the device will not attempt to reprint… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.37 | Scalarwide-a4 | read-write | optional | Returns or changes the wide A4 logical page size setting. If eOn, then the margins/printable area of A4 paper will be changed to allow 80 10-pitch characters t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.38 | Scalardark-courier | read-write | optional | Returns or changes the dark Courier setting. If eOn, then the Courier font used will approximate the same darkness as the LaserJet III printer. If eOff, then t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.39 | Scalardefault-bits-per-pixel | read-write | optional | Controls the number of levels used (per pixel) when printing grayscale or color images. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3 | Nodepdl-pcl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.5 | Scalarpcl-total-page-count | read-write | optional | Total number of PCL pages printed by the device. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.13 | Scalarpcl-default-font-height | read-write | optional | Returns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.14 | Scalarpcl-default-font-source | read-write | optional | Returns or changes the value of the default font source variable in NVRAM. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.15 | Scalarpcl-default-font-number | read-write | optional | Returns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an <badValue>. Additiona… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.16 | Scalarpcl-default-font-width | read-write | optional | Returns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4 | Nodepdl-postscript | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.5 | Scalarpostscript-total-page-count | read-write | optional | Total number of PostScript pages printed by the device. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.11 | Scalarpostscript-print-errors | read-write | optional | Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.5 | Nodepjl | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.5.1 | Scalarpjl-password | read-only | optional | Returns PJL password, if the password is not set (zero). If the password is set, then attempting to retrieve the password causes an <genErr> to occur and will … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7 | Nodefax-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1 | Nodesettings-fax-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.1 | Scalarfax-rxscale | read-write | optional | Received faxes are to be printed at a reduced scale percentage. Value of 0 indicates auto-scaled printing based on the length of the received fax image and the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.3 | Scalarfax-noise-volume | read-write | optional | Range is 0..100, where 0 = quietest possible, and 100 = loudest possible. A device shall divide this value into ranges corresponding to the possible volumes. A… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.6 | Scalarfax-download | read-write | optional | Note: Changed enumeration values in a non-backwards manner in version 4.7. Handshake mechanism between host and device to initiate and coordinate the download … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.7 | Scalarfax-silent-detection | read-write | optional | When enabled, this object causes the FAX machine to assume that the caller is a FAX even though the line has remained silent for a time (i.e., no CNG detected)… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.8 | Scalarfax-ring-enable | read-write | optional | When the phone line rings, this object determines whether an audible ring shall be emitted. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.9 | Scalarfax-country | read-write | optional | Note: Non-backwards compatible change make in version 4.7. Returns which country the telephone-electronics (LIU) is configured for. If this object is implement… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.10 | Scalarfax-tx-phone-number | write-only | optional | Phone number about to be dialed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.14 | Scalarfax-redial-time | read-only | optional | Number of seconds one must wait between the current redial (set by FAX-WHICH-REDIAL) and any prior dialing. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.18 | Scalarfax-pstn-access-code | read-write | optional | The code used within a PBX to get access to an outside PSTN line. Typically this is ''9''. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.19 | Scalarfax-rx-disposition | read-write | optional | Indicates what is to be done with the incoming fax call. ePrintOnly - New fax arrivals only go to the printer. If printer becomes unavailable, the fax is store… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.21 | Scalarfax-error-correction-mode | read-write | optional | Indicates whether the device is configured to send and receive faxes in error correction mode (ECM). This object controls both receiving and transmitting in EC… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.22 | Scalarfax-report-transmission | read-write | optional | Provides a host application with the ability to print a fax transmission report. The supported enumerations are: eNone - no transmission report printed ePrintR… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.23 | Scalarfax-report-activity-log | read-write | optional | Specifies when a report of fax transactions is to be printed. eNever - to never print a transaction report. eThreshold - to automatically print a transaction r… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.24 | Scalarfax-dial-tone-detection | read-write | optional | Determines whether the fax machine waits for a dial tone before dialing a fax number. eEnabled - causes the fax machine to wait until a dial tone is recognized… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.25 | Scalarfax-alarm-volume | read-write | optional | Range is 0..100, where 0 = quietest possible, and 100 = loudest possible. A device shall divide this value into ranges corresponding to the possible volumes an… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.26 | Scalarfax-beep-volume | read-write | optional | Range is 0..100, where 0 = quietest possible, and 100 = loudest possible. A device shall divide this value into ranges corresponding to the possible volumes an… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.27 | Scalarfax-ring-volume | read-write | optional | Range is 0..100, where 0 = quietest possible, and 100 = loudest possible. A device shall divide this value into ranges corresponding to the possible volumes an… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.28 | Scalarfax-master-host | read-write | optional | Identifies the hostname of the master host to which the device is connected. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.29 | Scalarfax-thumbnail-enable | read-write | optional | Controls whether or not a thumbnail reprint of the first page of a fax shall be included on the fax call report. When set to eEnabled a thumbnail shall be incl… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.30 | Scalarfax-phone-pickup-enable | read-write | optional | This object is included to handle the situation where a fax machine and a telephone share the same phone line. If a call picked up at the phone turns out to be… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.31 | Scalarfax-adf-scan-count | read-write | optional | This object tracks the page count for the pages scanned for faxing from the ADF. In order to write this object SERVICE-PASSWORD must be set correctly. Addition… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.32 | Scalarfax-print-page-count | read-write | optional | This object tracks the page count for the pages sent to the print engine for fax jobs. In order to write this object SERVICE-PASSWORD must be set correctly. Ad… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.33 | Scalarfax-download-page-count | read-write | optional | This object tracks the page count for the pages downloaded to the peripheral for fax jobs. In order to write this object SERVICE-PASSWORD must be set correctly… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.34 | Scalarfax-upload-page-count | read-write | optional | This object tracks the page count for the pages uploaded from the peripheral for fax jobs. In order to write this object SERVICE-PASSWORD must be set correctly… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.36 | Scalarfax-flatbed-scan-count | read-write | optional | This object tracks the page count for the pages scanned for faxing from the flatbed. In order to write this object the SERVICE-PASSWORD must be set. Additional… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.37 | Scalardefault-fax-glass-size | read-write | optional | Indicates the default fax glass size. Additional information: Indicates the default fax glass size. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.1.38 | Scalarfax-cold-reset-fax-glass-size | read-write | optional | Returns or sets the fax glass size that is used as the DEFAULT-FAX-GLASS-SIZE when a cold reset occurs. Additional information: Returns or sets the fax glass s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2 | Nodestatus-fax-proc-sub | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.1 | Scalarfax-upload | read-write | optional | Note: The enumeration values for this object where changed in a non-backwards compatible manner in version 4.7. Handshake mechanism between host and device to … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.2 | Scalarfax-min-rings-pickup | read-only | optional | Indicates the minimum legal rings before pickup. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.3 | Scalarfax-max-rings-pickup | read-only | optional | Indicates the maximum legal rings before pickup. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.4 | Scalarfax-max-redials | read-only | optional | Maximum number of allowed redials. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.5 | Scalarfax-additional-wait | read-only | optional | Number of additional seconds to wait before beginning a FAX-DOWNLOAD. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.6 | Scalarfax-download-error | read-only | optional | Error status of the fax download session. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.7 | Scalarfax-upload-error | read-only | optional | Error status of the fax upload session. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.2.8 | Scalarfax-firmware-revision | read-only | optional | This object identifies the fax firmware ROM revision code. The format is device specific and shall be specified in the device POS. Additional information: This… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.3 | Nodefax-forwarding | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.3.7.3.3 | Scalarfax-forwarding-phone-num | read-write | optional | Phone number digits of the remote fax station where arrived faxes are to be forwarded. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4 | Nodedestination-subsystem | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1 | Nodeprint-engine | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1 | Nodesettings-prt-eng | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.5 | Scalarprint-density | read-write | optional | Returns or sets the print density setting. Print density is the instantaneous amount of marking agent applied to the paper while printing. A value of zero has … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9 | Nodemarking-agent-density | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.1 | Scalarmarking-agent-density-setting | read-write | optional | Returns or sets the marking agent density setting for each of the marking agents installed. The Marking Agent (aka Print) density is the instantaneous amount o… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.2 | Scalarmarking-agent-highlights-density-setting | read-write | optional | Returns or sets the marking agent highlights density setting for each of the marking agents installed. The value of this object is in the range of -5..+5. The … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.3 | Scalarmarking-agent-midtones-density-setting | read-write | optional | Returns or sets the marking agent midtones density setting for each of the marking agents installed. The value of this object is in the range of -5..+5. See MA… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.4 | Scalarmarking-agent-shadows-density-setting | read-write | optional | Returns or sets the marking agent shadows density setting for each of the marking agents installed. The value of this object is in the range of -5..+5. See MAR… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.18 | Scalarinvalid-personality-reports-enabled | read-write | optional | Read or configure wether invalid personality reports are enabled or disabled for a product. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.19 | Scalarfast-first-page-out | read-write | optional | Return or set the value of the fast first page out setting. Additional information: Return or set the value of the fast first page out setting. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.20 | Scalarcalibration-power-on-initiation | read-write | optional | This object determines when a power on calibration occurs. If eOn, then the calibration occurs immediately following boot. If eOff, then it never occurs. If eD… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.21 | Scalarcalibration-power-on-delay | read-write | optional | This is the delay interval for the power on calibration in minutes. This PML object is only used if the CALIBRATION-POWER-ON-INITIATION PML object is set to eD… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.22 | Scalarcalibration-pages-printed-initiation | read-write | optional | The number of pages that will be printed prior to an automatically initiated print calibration. If set to 0, it turns this calibration off. Additional informat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.23 | Scalarcalibration-timer-initiation | read-write | optional | This is a timer in minutes that will be set in between calibrations. When the timer expires, a calibration will automatically be initiated. If set to 0, it tur… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2 | Nodestatus-prt-eng | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.5 | Scalartotal-engine-page-count | read-write | optional | Total number of pages printed by the device. POS indicates if the total engine page count is kept in NVRAM, and the maximum supported value before the page cou… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.6 | Scalartotal-mono-page-count | read-write | optional | Total number of black pages printed by the device. Additional information: Total number of mono pages printed by the device. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.7 | Scalartotal-color-page-count | read-write | optional | Total number of color pages printed by the device. Additional information: Total number of color pages printed by the device. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.22 | Scalarduplex-page-count | read-write | optional | Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not mark… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.26 | Scalarprint-engine-revision | read-only | optional | Print engine revision string. Additional information: Print engine revision string. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.34 | Scalarprint-engine-jam-count | read-write | optional | Total number of pages jammed in the print engine's life time. The POS indicates if the total jam count is kept in NVRAM and the maximum supported value before … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.35 | Scalarprint-engine-mispick-count | read-write | optional | Total number of pages mispicked in the print engine's life time. The POS indicates if the total mispick count is kept in NVRAM and the maximum supported value … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3 | Nodeintray | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1 | Nodesettings-intray | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.5 | Scalarmp-tray | read-write | optional | Returns or changes the value of the multi-purpose (MP) tray configuration variable. The MP tray can be configured to operate as an additional input tray (eCass… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.6 | Scalartray-lock | read-write | optional | Returns or changes the list of locked input trays. The printer only pulls media from a locked input tray when the input tray is specifically requested by the p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.7 | Scalarcustom-paper-dim-unit | read-write | optional | The units of measure used to specify the width and height of the printer's custom paper. The unit of measure of eTenThousandthsOfInches is 0.0001 inches. Addit… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.8 | Scalarcustom-paper-feed-dim | read-write | optional | Sets the printer's custom paper dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.9 | Scalarcustom-paper-xfeed-dim | read-write | optional | Sets the printer's custom paper dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3 | Nodeintrays | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1 | Nodeintray1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.1 | Scalartray1-media-size-loaded | read-write | optional | Returns the media size that is currently configuredconfigured in tray #1. This object can be set to indicate the media size currently loaded, if the printer su… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.13 | Scalartray1-fuser-temperature | read-write | optional | The fuser temperature to be used when printing media from Tray 1. The value zero is the default temperature. Values less than zero are progressively lower and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2 | Nodeintray2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.1 | Scalartray2-media-size-loaded | read-write | optional | Returns the media size that is currently configured in tray #2. Complete list of supported media sizes along with their dimensions are listed in the ''Media Si… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.13 | Scalartray2-fuser-temperature | read-write | optional | The fuser temperature to be used when printing media from Tray 2. The value zero is the default temperature. Values less than zero are progressively lower and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3 | Nodeintray3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.1 | Scalartray3-media-size-loaded | read-write | optional | Returns the media size that is currently configured in tray #3. Complete list of supported media sizes along with their dimensions are listed in the ''Media Si… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.13 | Scalartray3-fuser-temperature | read-write | optional | The fuser temperature to be used when printing media from Tray 3. The value zero is the default temperature. Values less than zero are progressively lower and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5 | Nodemarking-agent | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1 | Nodesettings-marking-agent | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.11 | Scalarmarker-density-calibration | read-write | optional | Returns the calibration status or triggers a calibration cycle. All calibration procedures are used if set to eCalibrateALL. If set to eCalibrateDMAX then a fu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6 | Nodeimaging | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.5 | Scalardefault-ret | read-write | optional | Returns or changes the Resolution Enhancement Technology setting. Devices that only support eOff and eOn should map all other values to eOn and always return t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.7 | Scalardefault-print-quality | read-write | optional | Returns or sets the default print quality. A value of zero has the lowest print quality. A value of 100 has the highest print quality. Each POS should document… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8 | Nodeprint-media | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1 | Nodesettings-print-media | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.1 | Scalarmedia-names-available | read-only | optional | The value of this object controls which of the MEDIAx-NAME objects are supported. If a bit is set to zero, then attempting to get or set the corresponding MEDI… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3 | Nodemedia-info | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1 | Nodemedia1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.1 | Scalarmedia1-name | read-only | optional | Media 1 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.4 | Scalarmedia1-engine-media-mode | read-only | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: The eng… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2 | Nodemedia2 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.1 | Scalarmedia2-name | read-only | optional | Media 2 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.4 | Scalarmedia2-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3 | Nodemedia3 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.1 | Scalarmedia3-name | read-only | optional | Media 3 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.4 | Scalarmedia3-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4 | Nodemedia4 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.1 | Scalarmedia4-name | read-only | optional | Media 4 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.4 | Scalarmedia4-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5 | Nodemedia5 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.1 | Scalarmedia5-name | read-only | optional | Media 5 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.4 | Scalarmedia5-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6 | Nodemedia6 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.1 | Scalarmedia6-name | read-only | optional | Media 6 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.4 | Scalarmedia6-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7 | Nodemedia7 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.1 | Scalarmedia7-name | read-only | optional | Media 7 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.4 | Scalarmedia7-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8 | Nodemedia8 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.1 | Scalarmedia8-name | read-only | optional | Media 8 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.4 | Scalarmedia8-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9 | Nodemedia9 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.1 | Scalarmedia9-name | read-only | optional | Media 9 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.4 | Scalarmedia9-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10 | Nodemedia10 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.1 | Scalarmedia10-name | read-only | optional | Media 10 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.4 | Scalarmedia10-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11 | Nodemedia11 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.1 | Scalarmedia11-name | read-only | optional | Media 11 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.4 | Scalarmedia11-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12 | Nodemedia12 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.1 | Scalarmedia12-name | read-only | optional | Media 12 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.4 | Scalarmedia12-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13 | Nodemedia13 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.1 | Scalarmedia13-name | read-only | optional | Media 13 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.4 | Scalarmedia13-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14 | Nodemedia14 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.1 | Scalarmedia14-name | read-only | optional | Media 14 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.4 | Scalarmedia14-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15 | Nodemedia15 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.1 | Scalarmedia15-name | read-only | optional | Media 15 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.4 | Scalarmedia15-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16 | Nodemedia16 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.1 | Scalarmedia16-name | read-only | optional | Media 16 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.4 | Scalarmedia16-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17 | Nodemedia17 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.1 | Scalarmedia17-name | read-only | optional | Media 17 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.4 | Scalarmedia17-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18 | Nodemedia18 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.1 | Scalarmedia18-name | read-only | optional | Media 18 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.4 | Scalarmedia18-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19 | Nodemedia19 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.1 | Scalarmedia19-name | read-only | optional | Media 19 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.4 | Scalarmedia19-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20 | Nodemedia20 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.1 | Scalarmedia20-name | read-only | optional | Media 20 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.4 | Scalarmedia20-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21 | Nodemedia21 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.1 | Scalarmedia21-name | read-only | optional | Media 21 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.4 | Scalarmedia21-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22 | Nodemedia22 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.1 | Scalarmedia22-name | read-only | optional | Media 22 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.4 | Scalarmedia22-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23 | Nodemedia23 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23.1 | Scalarmedia23-name | read-only | optional | Media 23 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.23.4 | Scalarmedia23-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24 | Nodemedia24 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24.1 | Scalarmedia24-name | read-only | optional | Media 24 name. Additional information: The symbol set for this string is Roman-8. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.24.4 | Scalarmedia24-engine-media-mode | read-write | optional | The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4 | Nodemedia-modes | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4.1 | Scalarengine-media-modes-supported1 | read-only | optional | The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: 'Normal,Rough,Low,Vellum… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10 | Nodeconsumables | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1 | Nodeconsumables-1 | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1 | Nodeconsumable-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.3 | Scalarconsumable-status-serial-number | read-only | optional | This object is used to report the serial number for this consumable. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5 | Nodeconsumables-status | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1 | Nodeconsumables-life | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.1 | Scalarconsumable-life-usage-units-remaining | read-only | optional | This object reports the current estimate of the number of usage units that remain before this supply is depleted. An installed supply that cannot report such a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.3 | Scalarconsumable-life-low-threshold | read-write | optional | This object is used to report and/or modify a threshold value indicating the point in the life of a consumable or supply at which a transition to a LOW state w… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.6 | Nodeconsumables-test | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.6.1 | Scalarconsumable-test-password | write-only | optional | When set with the correct integer password value this object is used to enable certain device specific test capabilities. When set with any incorrect integer v… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2 | Nodefax-send | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.1 | Nodesettings-fax-send | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.1.1 | Scalarfax-resolution | read-write | optional | struct { unsigned_32bit x_res; /* 1st four bytes; big endian */ unsigned_32bit y_res; /* 2nd four bytes; big endian */ } Sets the send fax resolution. The x an… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.1.2 | Scalarfax-contrast | read-write | optional | Behaves as SCL's 'Set Scanner Contrast Level' command which is used for setting the sending fax contrast level. Range is 0..100. Additional information: Behave… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.1.3 | Scalarfax-pixel-data-type | read-write | optional | Sets the scanning method used when sending a fax. eBiLevelThesholded - One bit per pixel, using simple thresholding of greyscale scan data. eBiLevelHalfToned -… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.2 | Nodestatus-fax-send | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.2.1 | Scalarnot-ready-fax-send | read-only | optional | Indicates if the sending fax sub-system in the device is not ready. If there are no items in the collection (i.e. no bits are set), then the sending fax sub-sy… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.5 | Nodetransmit-fax | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.2.5.3 | Scalarfax-allow-redials | read-write | optional | When eTrue, the FAX machine can redial a phone number if the prior call failed for some reason. When eFalse, such redialing will not occur. Additional informat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5 | Nodecopier | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1 | Nodesettings-copier | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.2 | Scalarcopier-contrast | read-write | optional | Behaves as SCL's 'Set Scanner Contrast Level' command which is used for setting the copier contrast level. Range is 0..100. Additional information: Behaves as … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.4 | Scalarcopier-reduction | read-write | optional | Percentage reduction desired for the copier. A value less than or equal to zero is invalid. A value greater than 100 accomplishes magnification. A device is al… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.6 | Scalarcopier-num-copies | read-write | optional | Returns or changes the number of copies to be printed in the next Host requested copy operation. Additional information: Returns or changes the number of copie… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.7 | Scalarcopier-collation | read-write | optional | Enables the device with local copier capability that also supports outputting multiple copies of a multi-paged source document to print in a collated fashion. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.11 | Scalarcopier-enlargement-maximum | read-only | optional | Maximum value that the host may set COPIER-REDUCTION to. A value less than or equal to zero is invalid. Additional information: Maximum value that the host may… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.12 | Scalarcopier-reduction-maximum | read-only | optional | Minimum value that the host may set COPIER-REDUCTION to. A value less than or equal to zero is invalid. Additional information: Minimum value that the host may… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.13 | Scalarcopier-quality | read-write | optional | Returns or sets the copier quality. This value is stored in NVRAM, hence the value is saved over power cycles. Additional information: This value is stored in … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.19 | Scalarcopier-adf-page-count | read-write | optional | This object tracks the page count for the pages scanned for copying through the ADF. In order to write this object SERVICE-PASSWORD must be set correctly. Addi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.20 | Scalarcopier-print-page-count | read-write | optional | This object tracks the page count for the pages sent to the print engine, for copy jobs. In order to write this object SERVICE-PASSWORD must be set correctly. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.21 | Scalarcopier-job-media-size | read-write | optional | The user can set a copy job setting for paper size using the COPIER-JOB-MEDIA-SIZE object, which is independent of other functions in the device. The device be… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.22 | Scalarcopier-job-quality | read-write | optional | Returns or sets the copier quality. Additional information: Returns or sets the copier quality. eCopierQualityFast is supported but gets mapped to normal. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.23 | Scalarcopier-job-collation | read-write | optional | Enables the device with local copier capability that also supports outputting multiple copies of a multi-paged source document to print in a collated fashion. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.24 | Scalarcopier-job-num-copies | read-write | optional | Returns or changes the number of copies to be printed in the next Host requested copy operation. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.25 | Scalarcopier-job-reduction | read-write | optional | Percentage reduction desired for the copier. A device is allowed to support a set of values (documented in its POS), instead of the full range. <OKNearesetLega… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.26 | Scalarcopier-job-contrast | read-write | optional | Used to set the copier contrast level. Additional information: Behaves as SCL's 'Set Scanner Contrast Level' command which is used for setting the copier contr… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.27 | Scalarcopier-job | read-write | optional | Controls initiating and canceling a copy job. Additional information: Controls initiating and canceling a copy job. eCopierIdle : indicates that a copy functio… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.28 | Scalardefault-copy-duplex-mode | read-write | optional | Returns or sets the duplex copying mode. Duplex printing is when printing occurs on both sides of a sheet of media. Long edge binding is also called vertical b… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.44 | Scalarcopier-flatbed-page-count | read-write | optional | This object tracks the page count for the pages scanned for copying from the flatbed. In order to write this object SERVICE-PASSWORD must be set correctly. Add… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.45 | Scalarcopier-pages-per-sheet | read-write | optional | Returns or sets the copier number of input pages per output sheet. This is also known as nup. This value is stored in NVRAM, hence the value is saved over powe… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.46 | Scalarcopier-job-pages-per-sheet | read-write | optional | Returns or sets the copy value for how many input pages per output sheet. Additional information: Enables the device with local copier capability that also sup… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.47 | Scalarcopier-fit-to-page | read-write | optional | Returns or sets the copy setting for fit to page. This value is stored in NVRAM, hence the value is saved over power cycles. Additional information: Enables th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.48 | Scalarcopier-job-fit-to-page | read-write | optional | Returns or sets the copy value for fit to page. Additional information: Enables the device with local copier capability to fit the input image size automatical… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.5.1.49 | Scalarcopier-pages-per-sheet-maximum | read-only | optional | Maximum pages per sheet value supported by the COPIER- PAGES-PER-SHEET and COPIER-JOB-PAGES-PER-SHEET objects. A value less than or equal to zero is invalid. A… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2 | Nodeprintmib | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5 | NodeprtGeneral | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1 | NodeprtGeneralTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1 | NodeprtGeneralEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.1 | ScalarprtGeneralConfigChanges | read-only | optional | Counts configuration changes that change the capabilities of a printer, such as the addition/deletion of input/output bins, the addition/deletion of interprete… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.2 | ScalarprtGeneralCurrentLocalization | read-write | optional | The value of the prtLocalizationIndex corresponding to the current language, country, and character set to be used for localized string values that are identif… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.3 | ScalarprtGeneralReset | read-write | optional | Setting this value to `powerCycleReset', `resetToNVRAM', or `resetToFactoryDefaults' will result in the resetting of the printer. When read, this object will a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.4 | ScalarprtGeneralCurrentOperator | read-write | optional | The name of the person who is responsible for operating this printer. It is suggested that this string include information that would enable other humans to re… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.5 | ScalarprtGeneralServicePerson | read-write | optional | The name of the person responsible for servicing this printer. It is suggested that this string include information that would enable other humans to reach the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.6 | ScalarprtInputDefaultIndex | read-only | optional | The value of prtInputIndex corresponding to the default input sub-unit: that is, this object selects the default source of input media. This value shall be -1 … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.7 | ScalarprtOutputDefaultIndex | read-only | optional | The value of prtOutputIndex corresponding to the default output sub-unit; that is, this object selects the default output destination. This value shall be -1 i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.8 | ScalarprtMarkerDefaultIndex | read-only | optional | The value of prtMarkerIndex corresponding to the default marker sub-unit; that is, this object selects the default marker. Additional information: The product … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.9 | ScalarprtMediaPathDefaultIndex | read-only | optional | The value of prtMediaPathIndex corresponding to the default media path; that is, the selection of the default media path. Additional information: The only vali… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.10 | ScalarprtConsoleLocalization | read-write | optional | The value of the prtLocalizationIndex corresponding to the language, country, and character set to be used for the console. This localization applies both to t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.11 | ScalarprtConsoleNumberOfDisplayLines | read-only | optional | The number of lines on the printer's physical display. This value is 0 if there are no lines on the physical display or if there is no physical display. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.12 | ScalarprtConsoleNumberOfDisplayChars | read-only | optional | The number of characters per line displayed on the physical display. This value is 0 if there are no lines on the physical display or if there is no physical d… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.13 | ScalarprtConsoleDisable | read-only | optional | If the object prtConsoleDisable has value 'operatorConsoleDisabled' then input is not accepted from the operator console. If the object prtConsoleDisable has t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.16 | ScalarprtGeneralPrinterName | read-write | optional | An administrator-specified name for this printer. Depending upon implementation of this printer, the value of this object may or may not be same as the value f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.17 | ScalarprtGeneralSerialNumber | read-only | optional | A recorded serial number for this device that indexes some type device catalog or inventory. This value is usually set by the device manufacturer but the MIB s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.18 | ScalarprtAlertCriticalEvents | read-only | optional | A running counter of the number of critical alert events that have been recorded in the alert table. The value of this object is RESET in the event of a power … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.19 | ScalarprtAlertAllEvents | read-only | optional | A running counter of the total number of alert event entries (critical and non-critical) that have been recorded in the alert table Additional information: Thi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.2 | NodeprtStorageRefTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.2.1 | NodeprtStorageRefEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.2.1.2 | ScalarprtStorageRefIndex | read-only | optional | The value of the hrDeviceIndex of the printer device that this storageEntry is associated with. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.3 | NodeprtDeviceRefTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.3.1 | NodeprtDeviceRefEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.5.3.1.2 | ScalarprtDeviceRefIndex | read-only | optional | The value of the hrDeviceIndex of the printer device that this deviceEntry is associated with. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.6 | NodeprtCover | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1 | NodeprtCoverTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1 | NodeprtCoverEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1.2 | ScalarprtCoverDescription | read-only | optional | The manufacturer provided cover sub-mechanism name in the localization specified by prtGeneralCurrentLocalization. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1.3 | ScalarprtCoverStatus | read-only | optional | The status of this cover sub-unit. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.7 | NodeprtLocalization | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1 | NodeprtLocalizationTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1 | NodeprtLocalizationEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.2 | ScalarprtLocalizationLanguage | read-only | optional | A two character language code from ISO 639. Examples en, gb, ca, fr, de. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.3 | ScalarprtLocalizationCountry | read-only | optional | A two character country code from ISO 3166, a blank string (two space characters) shall indicate that the country is not defined. Examples: US, FR, DE, ... |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.4 | ScalarprtLocalizationCharacterSet | read-only | optional | The coded character set used for this localization. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8 | NodeprtInput | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2 | NodeprtInputTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1 | NodeprtInputEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.2 | ScalarprtInputType | read-only | optional | The type of technology (discriminated primarily according to feeder mechanism type) employed by the input sub-unit. Note, the Optional Input Class provides for… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.3 | ScalarprtInputDimUnit | read-only | optional | The unit of measurement for use calculating and relaying dimensional values for this input sub-unit. Additional information: Following is a table of paper size… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.4 | ScalarprtInputMediaDimFeedDirDeclared | read-only | optional | This object provides the value of the declared dimension, in the feed direction, of the media that is (or, if empty, was or will be) in this input sub-unit. Th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.5 | ScalarprtInputMediaDimXFeedDirDeclared | read-only | optional | This object provides the value of the declared dimension, in the cross feed direction, of the media that is (or, if empty, was or will be) in this input sub-un… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.6 | ScalarprtInputMediaDimFeedDirChosen | read-only | optional | The printer will act as if media of the chosen dimension (in the feed direction) is present in this input source. Note that this value will be used even if the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.7 | ScalarprtInputMediaDimXFeedDirChosen | read-only | optional | The printer will act as if media of the chosen dimension (in the cross feed direction) is present in this input source. Note that this value will be used even … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.8 | ScalarprtInputCapacityUnit | read-only | optional | The unit of measurement for use in calculating and relaying capacity values for this input sub-unit. Additional information: A sheet is a single piece of 20 po… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.9 | ScalarprtInputMaxCapacity | read-only | optional | The maximum capacity of the input sub-unit in input sub-unit capacity units (PrtCapacityUnitTC). There is no convention associated with the media itself so thi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.10 | ScalarprtInputCurrentLevel | read-only | optional | The current capacity of the input sub-unit in input sub-unit capacity units (PrtCapacityUnitTC). If this input sub-unit can reliably sense this value, the valu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.11 | ScalarprtInputStatus | read-only | optional | The current status of this input sub-unit. Additional information: The default value assumes that media is loaded in the tray. When there is not media loaded i… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.12 | ScalarprtInputMediaName | read-write | optional | A description of the media contained in this input sub-unit; This description is intended for display to a human operator. This description is not processed by… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.13 | ScalarprtInputName | read-only | optional | The name assigned to this input sub-unit. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.14 | ScalarprtInputVendorName | read-only | optional | The vendor name of this input sub-unit. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.15 | ScalarprtInputModel | read-only | optional | The model name of this input sub-unit. Additional information: The product does not specify model names for the input trays. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.16 | ScalarprtInputVersion | read-only | optional | The version of this input sub-unit. Additional information: The product does not specify version numbers for the input trays. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.17 | ScalarprtInputSerialNumber | read-only | optional | The serial number assigned to this input sub-unit. Additional information: The product does not specify serial numbers for the input trays. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.18 | ScalarprtInputDescription | read-only | optional | A free-form text description of this input sub-unit in the localization specified by prtGeneralCurrentLocalization. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.19 | ScalarprtInputSecurity | read-only | optional | Indicates if this input sub-unit has some security associated with it. Additional information: No security mechanism provided. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9 | NodeprtOutput | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2 | NodeprtOutputTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1 | NodeprtOutputEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.2 | ScalarprtOutputType | read-only | optional | The type of technology supported by this output sub-unit. Additional information: The product has only one output bin, a face-down bin located at the top of th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.3 | ScalarprtOutputCapacityUnit | read-only | optional | The unit of measurement for use in calculating and relaying capacity values for this output sub-unit. Additional information: A sheet is a single piece of 20 p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.4 | ScalarprtOutputMaxCapacity | read-only | optional | The maximum capacity of this output sub-unit in output sub-unit capacity units (PrtCapacityUnitTC). There is no convention associated with the media itself so … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.5 | ScalarprtOutputRemainingCapacity | read-only | optional | The remaining capacity of the possible output sub-unit capacity in output sub-unit capacity units (PrtCapacityUnitTC) of this output sub-unit. If this output s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.6 | ScalarprtOutputStatus | read-only | optional | The current status of this output sub-unit. Additional information: The product cannot sense the output tray so this object will always return 5 (Unknown Statu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10 | NodeprtMarker | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2 | NodeprtMarkerTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1 | NodeprtMarkerEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.2 | ScalarprtMarkerMarkTech | read-only | optional | The type of marking technology used for this marking sub-unit. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.3 | ScalarprtMarkerCounterUnit | read-only | optional | The unit that will be used by the printer when reporting counter values for this marking sub-unit. The time units of measure are provided for a device like a s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.4 | ScalarprtMarkerLifeCount | read-only | optional | The count of the number of units of measure counted during the life of printer using units of measure as specified by prtMarkerCounterUnit. Additional informat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.5 | ScalarprtMarkerPowerOnCount | read-only | optional | The count of the number of units of measure counted since the equipment was most recently powered on using units of measure as specified by prtMarkerCounterUni… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.6 | ScalarprtMarkerProcessColorants | read-only | optional | The number of process colors supported by this marker. A process color of 1 implies monochrome. The value of this object and prtMarkerSpotColorants cannot both… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.7 | ScalarprtMarkerSpotColorants | read-only | optional | The number of spot colors supported by this marker. The value of this object and prtMarkerProcessColorants cannot both be 0. Must be 0 or greater. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.8 | ScalarprtMarkerAddressabilityUnit | read-only | optional | The unit of measure of distances, as applied to the marker's resolution. Additional information: This will always be ePtenThousandthsOfInches, no matter what C… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.9 | ScalarprtMarkerAddressabilityFeedDir | read-only | optional | The maximum number of addressable marking positions in the feed direction per 10000 units of measure specified by prtMarkerAddressabilityUnit. A value of (-1) … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.10 | ScalarprtMarkerAddressabilityXFeedDir | read-only | optional | The maximum number of addressable marking positions in the cross feed direction in 10000 units of measure specified by prtMarkerAddressabilityUnit. A value of … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.11 | ScalarprtMarkerNorthMargin | read-only | optional | The margin, in units identified by prtMarkerAddressabilityUnit, from the leading edge of the medium as the medium flows through the marking engine with the sid… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.12 | ScalarprtMarkerSouthMargin | read-only | optional | The margin from the South edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.13 | ScalarprtMarkerWestMargin | read-only | optional | The margin from the West edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.14 | ScalarprtMarkerEastMargin | read-only | optional | The margin from the East edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.15 | ScalarprtMarkerStatus | read-only | optional | The current status of this marker sub-unit. Additional information: The default value assumes the printer is idle and has no malfunctions. Default - 0 (Availab… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11 | NodeprtMarkerSupplies | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1 | NodeprtMarkerSuppliesTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1 | NodeprtMarkerSuppliesEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.2 | ScalarprtMarkerSuppliesMarkerIndex | read-only | optional | The value of prtMarkerIndex corresponding to the marking sub-unit with which this marker supply sub-unit is associated. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.3 | ScalarprtMarkerSuppliesColorantIndex | read-only | optional | The value of prtMarkerColorantIndex corresponding to the colorant with which this marker supply sub-unit is associated. This value shall be 0 if there is no co… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.4 | ScalarprtMarkerSuppliesClass | read-only | optional | Indicates whether this supply entity represents a supply that is consumed or a receptacle that is filled. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.5 | ScalarprtMarkerSuppliesType | read-only | optional | The type of this supply. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.6 | ScalarprtMarkerSuppliesDescription | read-only | optional | The description of this supply container/receptacle in the localization specified by prtGeneralCurrentLocalization. Additional information: |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.7 | ScalarprtMarkerSuppliesSupplyUnit | read-only | optional | Unit of measure of this marker supply container/receptacle. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.8 | ScalarprtMarkerSuppliesMaxCapacity | read-only | optional | The maximum capacity of this supply container/receptacle expressed in prtMarkerSuppliesSupplyUnit. If this supply container/receptacle can reliably sense this … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.9 | ScalarprtMarkerSuppliesLevel | read-only | optional | The current level if this supply is a container; the remaining space if this supply is a receptacle. If this supply container/receptacle can reliably sense thi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12 | NodeprtMarkerColorant | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1 | NodeprtMarkerColorantTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1 | NodeprtMarkerColorantEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.2 | ScalarprtMarkerColorantMarkerIndex | read-only | optional | The value of prtMarkerIndex corresponding to the marker sub-unit with which this colorant entry is associated. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.3 | ScalarprtMarkerColorantRole | read-only | optional | The role played by this colorant. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.4 | ScalarprtMarkerColorantValue | read-only | optional | The name of the color of this colorant using standardized string names from ISO 10175 (DPA) and ISO 10180 (SPDL) which are: other unknown white red green blue … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.12.1.1.5 | ScalarprtMarkerColorantTonality | read-only | optional | The distinct levels of tonality realizable by a marking sub-unit when using this colorant. This value does not include the number of levels of tonal difference… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13 | NodeprtMediaPath | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4 | NodeprtMediaPathTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1 | NodeprtMediaPathEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.2 | ScalarprtMediaPathMaxSpeedPrintUnit | read-only | optional | The unit of measure used in specifying the speed of all media paths in the printer. Additional information: ePimpressionsPerHour is the value that will always … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.3 | ScalarprtMediaPathMediaSizeUnit | read-only | optional | The units of measure of media size for use in calculating and relaying dimensional values for all media paths in the printer. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.4 | ScalarprtMediaPathMaxSpeed | read-only | optional | The maximum printing speed of this media path expressed in prtMediaPathMaxSpeedUnit's. A value of (-1) implies 'other'. Additional information: The page size f… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.5 | ScalarprtMediaPathMaxMediaFeedDir | read-only | optional | The maximum physical media size in the feed direction of this media path expressed in units of measure specified by PrtMediaPathMediaSizeUnit. A value of (-1) … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.6 | ScalarprtMediaPathMaxMediaXFeedDir | read-only | optional | The maximum physical media size across the feed direction of this media path expressed in units of measure specified by prtMediaPathMediaSizeUnit. A value of (… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.7 | ScalarprtMediaPathMinMediaFeedDir | read-only | optional | The minimum physical media size in the feed direction of this media path expressed in units of measure specified by prtMediaPathMediaSizeUnit. A value of (-2) … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.8 | ScalarprtMediaPathMinMediaXFeedDir | read-only | optional | The minimum physical media size across the feed direction of this media path expressed in units of measure specified by prtMediaPathMediaSizeUnit. A value of (… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.9 | ScalarprtMediaPathType | read-only | optional | The type of the media path for this media path. Additional information: This object describes how many paths there are through the engine disregarding the pape… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.10 | ScalarprtMediaPathDescription | read-only | optional | The manufacturer-provided description of this media path in the localization specified by prtGeneralCurrentLocalization. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.11 | ScalarprtMediaPathStatus | read-only | optional | The current status of this media path. Additional information: The default values assume the printer is idle. Default - 0 (Available and Idle) paper motion - 6… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15 | NodeprtInterpreter | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1 | NodeprtInterpreterTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1 | NodeprtInterpreterEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.2 | ScalarprtInterpreterLangFamily | read-only | optional | The family name of a Page Description Language (PDL) or control language which this interpreter in the printer can interpret or emulate. Additional information… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.3 | ScalarprtInterpreterLangLevel | read-only | optional | The level of the language which this interpreter is interpreting or emulating. This might contain a value like '5e' for an interpreter which is emulating level… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.4 | ScalarprtInterpreterLangVersion | read-only | optional | The date code or version of the language which this interpreter is interpreting or emulating. Additional information: These values are derived from the dateCod… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.5 | ScalarprtInterpreterDescription | read-only | optional | A string to identify this interpreter in the localization specified by prtGeneralCurrentLocalization as opposed to the language which is being interpreted. It … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.6 | ScalarprtInterpreterVersion | read-only | optional | The date code, version number, or other product specific information tied to this interpreter. This value is associated with the interpreter, rather than with … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.7 | ScalarprtInterpreterDefaultOrientation | read-write | optional | The current orientation default for this interpreter. This value may be overridden for a particular job (e.g., by a command in the input data stream). Addition… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.8 | ScalarprtInterpreterFeedAddressability | read-only | optional | The maximum interpreter addressability in the feed direction in 10000 prtMarkerAddressabilityUnits (see prtMarkerAddressabilityFeedDir ) for this interpreter. … |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.9 | ScalarprtInterpreterXFeedAddressability | read-only | optional | The maximum interpreter addressability in the cross feed direction in 10000 prtMarkerAddressabilityUnits (see prtMarkerAddressabilityXFeedDir) for this interpr… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.10 | ScalarprtInterpreterDefaultCharSetIn | read-write | optional | The default coded character set for input octets encountered outside a context in which the Page Description Language established the interpretation of the oct… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.11 | ScalarprtInterpreterDefaultCharSetOut | read-only | optional | The default character set for data coming from this interpreter through the printer's output channel (i.e. the 'backchannel'). This value shall be (2) if there… |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.12 | ScalarprtInterpreterTwoWay | read-only | optional | Indicates whether or not this interpreter returns information back to the host. |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.16 | NodeprtConsoleDisplayBuffer | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.16.5 | NodeprtConsoleDisplayBufferTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.16.5.1 | NodeprtConsoleDisplayBufferEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.2.16.5.1.2 | ScalarprtConsoleDisplayBufferText | read-only | optional | The content of a line in the logical display buffer of the operator's console of the printer. When a write operation occurs, normally a critical message, to on… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3 | Nodehrm | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2 | NodehrStorage | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.2 | ScalarhrMemorySize | read-only | mandatory | The amount of physical main memory contained by the host. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The unit of measure … |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3 | NodehrStorageTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1 | NodehrStorageEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.1 | ScalarhrStorageIndex | read-only | mandatory | A unique value for each logical storage area contained by the host. Refer to RFC 1514, Host Resources MIB, for more details. |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.2 | ScalarhrStorageType | read-only | mandatory | The type of storage represented by this entry. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The object is constant for the … |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.3 | ScalarhrStorageDescr | read-only | mandatory | A description of the type and instance of the storage described by this entry. Refer to RFC 1514, Host Resources MIB, for more details. Additional information:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.4 | ScalarhrStorageAllocationUnits | read-only | mandatory | The size, in bytes, of the data objects allocated from this pool. If this entry is monitoring sectors, blocks, buffers, or packets, for example, this number wi… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.5 | ScalarhrStorageSize | read-only | mandatory | The size of the storage represented by this entry, in units of hrStorageAllocationUnits. Refer to RFC 1514, Host Resources MIB, for more details. Additional in… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.6 | ScalarhrStorageUsed | read-only | mandatory | The amount of the storage represented by this entry that is allocated, in units of hrStorageAllocationUnits. Refer to RFC 1514, Host Resources MIB, for more de… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7 | ScalarhrStorageAllocationFailures | read-only | mandatory | The number of requests for storage represented by this entry that could not be honored due to not enough storage. It should be noted that as this object has a … |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3 | NodehrDevice | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2 | NodehrDeviceTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1 | NodehrDeviceEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.1 | ScalarhrDeviceIndex | read-only | mandatory | A unique value for each device contained by the host. The value for each device must remain constant at least from one re-initialization of the agent to the ne… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.2 | ScalarhrDeviceType | read-only | mandatory | An indication of the type of device. If this value is `hrDeviceProcessor { hrDeviceTypes 3 }' then an entry exists in the hrProcessorTable which corresponds to… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.3 | ScalarhrDeviceDescr | read-only | mandatory | A textual description of this device, including the device's manufacturer and revision, and optionally, its serial number. Refer to RFC 1514, Host Resources MI… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.4 | ScalarhrDeviceID | read-only | mandatory | The product ID for this device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The complete OID reported by this object is: .… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.5 | ScalarhrDeviceStatus | read-only | mandatory | The current operational state of the device described by this row of the table. A value unknown(1) indicates that the current state of the device is unknown. r… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.6 | ScalarhrDeviceErrors | read-only | mandatory | The number of errors detected on this device. It should be noted that as this object has a SYNTAX of Counter, that it does not have a defined initial value. Ho… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5 | NodehrPrinterTable | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1 | NodehrPrinterEntry | |||
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1.1 | ScalarhrPrinterStatus | read-only | mandatory | The current status of this printer device. When in the idle(1), printing(2), or warmup(3) state, the corresponding hrDeviceStatus should be running(2) or warni… |
| 1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1.2 | ScalarhrPrinterDetectedErrorState | read-only | mandatory | |
| 1.3.6.1.4.1.11.2.4 | Nodeinterface | |||
| 1.3.6.1.4.1.11.2.4.1 | Nodesimm | |||
| 1.3.6.1.4.1.11.2.4.1.1 | Nodesimm1 | |||
| 1.3.6.1.4.1.11.2.4.1.1.4 | Scalarsimm1-type | read-only | optional | Returns an indication of the type of option installed in SIMM slot 1. eEmpty means the device did not detect any option installed in the interface slot. eUnkno… |
| 1.3.6.1.4.1.11.2.4.1.1.5 | Scalarsimm1-capacity | read-only | optional | Returns an indication of the capacity of the SIMM installed in SIMM slot 1. The capacity is dependent on the type of option, as indicated by the SIMM1-TYPE obj… |
| 1.3.6.1.4.1.11.2.4.3 | NodenpCard | |||
| 1.3.6.1.4.1.11.2.4.3.1 | NodenpSys | |||
| 1.3.6.1.4.1.11.2.4.3.1.2 | ScalarnpSysStatusMessage | read-only | current | A status string reflecting the current state of the card and peripheral. |
| 1.3.6.1.4.1.11.2.4.3.1.10 | ScalarnpSysModelNumber | read-only | current | The HP model number of the device. |
| 1.3.6.1.4.1.11.2.4.3.1.11 | ScalarnpSysNetworkConnectors | read-only | current | This object describes the network connectors supported by the device. The value is a bit mask. A set bit indicates the connector is supported. Bit Value Connec… |
| 1.3.6.1.4.1.11.2.4.3.1.16 | ScalarnpSysCardServices1 | read-only | current | This object is a bitmap showing what services are available on the card. Bit 0 - IPX/SPX/NCP protocol stack Bit 1 - IP/TCP protocol stack Bit 2 - LLC/DLC proto… |
| 1.3.6.1.4.1.11.2.4.3.1.17 | ScalarnpSysCardServices2 | read-only | current | This object is a bitmap showing what services are available on the card. Bit 0 - XIP2 Bit 1 - PML Get/Set Bit 2 - PML Traps Bit 3 - Scan to Web Browser Bit 4 -… |
| 1.3.6.1.4.1.11.2.4.3.1.22 | ScalarnpSysCardServices3 | read-only | current | This object is a bitmap showing what services are available on the card. Bit 0 - 100T Bit 1 - Token Ring 802.5 Bit 2 - 802.11b Bit 3 - 80211.a Bit 4 - Bluetoot… |
| 1.3.6.1.4.1.11.2.4.3.4 | NodenpConns | |||
| 1.3.6.1.4.1.11.2.4.3.4.11 | ScalarnpConnsIP | read-only | current | Remote IP address of the node currently connected to the card. Zero if no connection is active. |
| 1.3.6.1.4.1.11.2.4.3.5 | NodenpCfg | |||
| 1.3.6.1.4.1.11.2.4.3.5.1 | ScalarnpCfgSource | read-write | current | This object indicates how the device obtained its IP configuration. |
| 1.3.6.1.4.1.11.2.4.3.5.2 | ScalarnpCfgYiaddr | read-write | current | The IP address assigned to the card from the BOOTP reply yiaddr field. |
| 1.3.6.1.4.1.11.2.4.3.5.3 | ScalarnpCfgSiaddr | read-only | current | The IP address of the TFTP server from the BOOTP reply siaddr field. |
| 1.3.6.1.4.1.11.2.4.3.5.5 | ScalarnpCfgLogServer | read-write | current | The IP address of the Syslog Server. If set via BOOTP (Tag: 7 field, lg=<ipaddress> ) then SNMP set will fail. If not set via BOOTP then SNMP set will succeed.… |
| 1.3.6.1.4.1.11.2.4.3.5.6 | ScalarnpCfgSyslogFacility | read-only | current | This specifies the facility identifier used in syslog messages generated by the card. |
| 1.3.6.1.4.1.11.2.4.3.5.7 | ScalarnpCfgAccessState | read-only | current | An indication of whether or not the requesting host is allowed to connect to the card as dictated by the access list. |
| 1.3.6.1.4.1.11.2.4.3.5.8 | ScalarnpCfgAccessListNum | read-only | current | The number of access list entries. |
| 1.3.6.1.4.1.11.2.4.3.5.9 | TablenpCfgAccessListTable | not-accessible | current | List of access addresses and masks. |
| 1.3.6.1.4.1.11.2.4.3.5.9.1 | RownpCfgAccessListEntry | not-accessible | current | Each entry contains an access address and mask. |
| 1.3.6.1.4.1.11.2.4.3.5.9.1.1 | ColumnnpCfgAccessListIndex | read-only | current | Index to the configuration access list table. |
| 1.3.6.1.4.1.11.2.4.3.5.9.1.2 | ColumnnpCfgAccessListAddress | read-write | current | The Access List Address contains the list of hosts or network of hosts that are allowed to connect to the print server over ip. When setting this object npCfgA… |
| 1.3.6.1.4.1.11.2.4.3.5.9.1.3 | ColumnnpCfgAccessListAddrMask | read-write | current | Address mask used to help determine whether or not a given IP address is allowed access to the print server. An IP address is allowed access if (Addr & AddrMas… |
| 1.3.6.1.4.1.11.2.4.3.5.12 | ScalarnpCfgSubnetMask | read-write | current | The subnet mask associated with the IP address of this card. |
| 1.3.6.1.4.1.11.2.4.3.5.13 | ScalarnpCfgDefaultGateway | read-write | current | This variable contains the IP address of the default router for this card. |
| 1.3.6.1.4.1.11.2.4.3.5.16 | ScalarnpCfgDomainName | read-write | current | The print server domain name. |
| 1.3.6.1.4.1.11.2.4.3.5.18 | ScalarnpCfgIPP | read-write | current | Below are the different values accepted by this OID. 0 - Disable IPP and IPP-S 1 - Enable IPP and IPP-S 2 - Enable IPP-S only 3 - Enable IPP only |
| 1.3.6.1.4.1.11.2.4.3.5.22 | ScalarnpCfgWINSNameServerIdPri | read-write | current | Primary name server for NetBIOS over TCP/IP. |
| 1.3.6.1.4.1.11.2.4.3.5.28 | ScalarnpCfgPasswd1Verify | read-write | current | Compares string value to passwd1 and returns OK if match, GENERAL ERROR if doesn't match. |
| 1.3.6.1.4.1.11.2.4.3.5.29 | ScalarnpCfgPasswd1 | read-write | current | Password for root or administrator. Get request returns either 'SET' or 'NOT_SET'. |
| 1.3.6.1.4.1.11.2.4.3.5.31 | ScalarnpCfgBanner | read-write | current | Line Printer Daemon Protocol (LPD) banner page per I/O port. (0) = Disabled (1) = Enabled Enabled by default. |
| 1.3.6.1.4.1.11.2.4.3.5.35 | ScalarnpCfgLinkType | read-write | current | Network link speed and communication mode. |
| 1.3.6.1.4.1.11.2.4.3.5.40 | ScalarnpCfgSnmpDefaultReadCmnty | read-write | current | Controls Default Read Community Name access. (0) = Disabled, i.e., default get community names FAIL to access target. (1) = Enabled, i.e., default get communit… |
| 1.3.6.1.4.1.11.2.4.3.5.44 | ScalarnpCfgBonjourServiceName | read-write | current | The name by which all the Jetdirect services will be advertised by Multicast Domain Name System (Bonjour). Must set a non empty string |
| 1.3.6.1.4.1.11.2.4.3.5.46 | ScalarnpCfgBonjourDomainName | read-only | current | The name used as the 'target name' in the DNS SRV records by Multicast Domain Name System (Bonjour). |
| 1.3.6.1.4.1.11.2.4.3.5.49 | ScalarnpCfgIPv6DomainName | read-write | current | IPv6 Domain Name. |
| 1.3.6.1.4.1.11.2.4.3.5.50 | ScalarnpCfgIPv6ConfigState | read-only | current | IPv6 stack status event; IPv6 enabled/disabled. |
| 1.3.6.1.4.1.11.2.4.3.5.56 | ScalarnpCfgIPv6DNSAddr1 | read-write | current | IPv6 DNS Address, priority 1. |
| 1.3.6.1.4.1.11.2.4.3.5.57 | ScalarnpCfgIPv6DNSAddr2 | read-write | current | IPv6 DNS Address, priority 2. |
| 1.3.6.1.4.1.11.2.4.3.5.59 | ScalarnpCfgIPConfigPrecedence | read-write | current | Allows to set uniform rules for parameter overwrite by different configuration methods. 0 - Manual 1 - TFTP 2 - DHCPv4/Bootp 3 - DHCPv6 - only if ipv6 is suppo… |
| 1.3.6.1.4.1.11.2.4.3.5.65 | ScalarnpCfgPortConfig | read-only | current | Network link speed and communication mode. |
| 1.3.6.1.4.1.11.2.4.3.5.85 | ScalarnpCfgWiFiDirectChannelNumber | read-write | current | The WiFi channel number used for Wireless/Wi-Fi Direct. Region Allowed Channels US & Worldwide Safe 1 - 11 Rest of the world 1 - 13 If wireless station is enab… |
| 1.3.6.1.4.1.11.2.4.3.5.86 | ScalarnpCfgWiFiDirectSSIDPrefix | read-only | current | The prefix of the network name (SSID) used for Wireless/Wi-Fi Direct. The value is 'HP-Print-XY-' where XY is the last two hex characters from the wireless MAC… |
| 1.3.6.1.4.1.11.2.4.3.5.87 | ScalarnpCfgWiFiDirectSSIDSuffix | read-write | current | The modifiable suffix of the network name (SSID) used for Wireless/Wi-Fi Direct. The default is '<sub brand> <hp model>', but it can be different depending on … |
| 1.3.6.1.4.1.11.2.4.3.5.88 | ScalarnpCfgWiFiDirectConnectionSecurity | read-write | optional | This is used to select the Wi-Fi Direct connection security method which differentiates how the connection is done between a mobile client and the printer. The… |
| 1.3.6.1.4.1.11.2.4.3.6 | NodenpTcp | |||
| 1.3.6.1.4.1.11.2.4.3.6.9 | ScalarnpTcpTFTPFileName | read-only | current | The TFTP configuration file name. |
| 1.3.6.1.4.1.11.2.4.3.6.10 | ScalarnpTcpTFTPServerId | read-only | current | TFTP server from which configuration information is obtained. |
| 1.3.6.1.4.1.11.2.4.3.6.11 | ScalarnpTcpSyslogMax | read-write | current | Maximum number of syslog packets to be sent per minute. 0 = Disabled. |
| 1.3.6.1.4.1.11.2.4.3.6.12 | ScalarnpTcpAppSyslogPriority | read-write | current | Priority below which the syslog messages will not be sent. Valid priority levels = 0 through 7. Disabled = 8. |
| 1.3.6.1.4.1.11.2.4.3.7 | NodenpCtl | |||
| 1.3.6.1.4.1.11.2.4.3.7.8 | ScalarnpCtlReconfig | read-write | current | Writing any value to this variable causes the card to reconfigure itself by doing the BOOTP/TFTP configuration activity. |
| 1.3.6.1.4.1.11.2.4.3.7.9 | ScalarnpCtlProtocolSet | read-write | current | This is a 4 byte integer value. The least significant bytes represent the protocols on the card. A value of '1' indicates a protocol that is enabled. A value o… |
| 1.3.6.1.4.1.11.2.4.3.7.14 | ScalarnpCtlSNMPEnableDisable | read-write | current | 0 = SNMP disabled 1 = SNMP enabled If SNMP is enabled, setting this object to 0 will disable SNMP on the print server. Once disabled it is not possible to enab… |
| 1.3.6.1.4.1.11.2.4.3.7.19 | ScalarnpCtlTelnet | read-write | current | Configure Telnet service. (0) = Telnet disabled (1) = Telnet enabled |
| 1.3.6.1.4.1.11.2.4.3.7.20 | ScalarnpCtlFTP | read-write | current | Configure File Transfer Protocol (FTP) service. (0) = Both FTP Print and Download Disabled (1) = Both FTP Print and Download Enabled (2) = FTP Print Enabled an… |
| 1.3.6.1.4.1.11.2.4.3.7.21 | ScalarnpCtlSLP | read-write | current | Configure Service Location Protocol (SLP) service. (0) = SLP disabled (1) = SLP enabled |
| 1.3.6.1.4.1.11.2.4.3.7.22 | ScalarnpCtlLPD | read-write | current | Configure Line Printer Daemon Protocol (LPD) service. (0) = LPD disabled (1) = LPD enabled |
| 1.3.6.1.4.1.11.2.4.3.7.24 | ScalarnpCtl9100 | read-write | current | Configure TCP port 9100 printing. (0) = port 9100 printing disabled (1) = port 9100 printing enabled |
| 1.3.6.1.4.1.11.2.4.3.7.26 | ScalarnpCtlSysLog | read-write | current | Configure Syslog service. (0) = Syslog service disabled (1) = Syslog service enabled Enabled by default. |
| 1.3.6.1.4.1.11.2.4.3.7.27 | ScalarnpCtlSnmpVersionAccess | read-write | current | Manages an SNMP version's read and write access to the MIB. |
| 1.3.6.1.4.1.11.2.4.3.7.28 | ScalarnpCtlSnmpV3InitAccount | read-write | current | Used to create initial SNMPv3 account. The following rules apply: 0 = clear init account, only if previously 0. 4 = Block init account, only cold reset will cl… |
| 1.3.6.1.4.1.11.2.4.3.7.29 | ScalarnpCtlBonjour | read-write | current | Configure Multicast Domain Name Service. (0) = Bonjour disabled (1) = Bonjour enabled |
| 1.3.6.1.4.1.11.2.4.3.7.32 | ScalarnpCtlNetworkConnectionMode | read-write | current | This object controls the selection of the active network interface used for communication. This is applicable to products supporting dual wired and wireless ne… |
| 1.3.6.1.4.1.11.2.4.3.7.34 | ScalarnpCtlIPSecurityPolicy | read-write | current | Disable IP Security (IPSec) or Firewall. Only disabling is allowed. |
| 1.3.6.1.4.1.11.2.4.3.7.36 | ScalarnpCtlWSDiscovery | read-write | current | Web Services Discovery enable/disable. |
| 1.3.6.1.4.1.11.2.4.3.7.37 | ScalarnpCtlWSPrint | read-write | current | Web Services Print enable/disable. |
| 1.3.6.1.4.1.11.2.4.3.7.38 | ScalarnpCtlLLMNR | read-write | current | Link-Local Multicast Name Resolution( LLMNR ) enable/disable. |
| 1.3.6.1.4.1.11.2.4.3.7.47 | ScalarnpCtlFpDot11WirelessState | read-write | current | Use for enabling and disabling Wireless Radio. The following values are defined: Disable = 0 Enable = 1 Default = 1(Enabled) |
| 1.3.6.1.4.1.11.2.4.3.7.57 | ScalarnpCtlWiFiDirectSSIDBroadcast | read-write | current | This is used to allow or hide broadcasting of the SSID (Network name). Allowed(Default) = 1 Not Allowed = 0 Not Allowed (0) only takes effect when npCfgWiFiDir… |
| 1.3.6.1.4.1.11.2.4.3.7.58 | ScalarnpCtlWiFiDirectHidePassphrase | read-write | optional | This controls display of the Wireless passphrase on configuration reports/pages or on the control panel. Show = 0 Hide = 1 This object also controls whether or… |
| 1.3.6.1.4.1.11.2.4.3.7.59 | ScalarnpCtlWiFiDirectHideSsid | read-write | optional | This controls display of the network name (SSID) on configuration reports/pages or on the control panel. Show = 0 Hide = 1 Hide (1) only takes effect when npCf… |
| 1.3.6.1.4.1.11.2.4.3.7.68 | ScalarnpCtlAirPrintStatus | read-write | current | Use to Enabled/Disabled AirPrint functionality. Disable = 0 Enable(Default) = 1 |
| 1.3.6.1.4.1.11.2.4.3.7.70 | ScalarnpCtlAllowRFC5746TLSSSLCompatibilityMode | read-write | current | Added to support RFC-5746. This OID can be use to enable/disable legacy SSL renegotiation. Disable = 0 Enable(Default) = 1 |
| 1.3.6.1.4.1.11.2.4.3.7.74 | ScalarnpCtlWiFiDirectState | read-write | current | Configure 802.11 Wireless/Wi-Fi Direct functionality 0 = Wireless/Wi-Fi Direct is disabled 1 = Wireless/Wi-Fi Direct is enabled |
| 1.3.6.1.4.1.11.2.4.3.7.79 | ScalarnpCtlAirScan | read-write | optional | Used to Enable/Disable the AirScan service. Disable = 0 Enable (Default) = 1 |
| 1.3.6.1.4.1.11.2.4.3.7.80 | ScalarnpCtlAirFax | read-write | optional | Used to Enable/Disable the AirFax service. Disable = 0 Enable (Default) = 1 |
| 1.3.6.1.4.1.11.2.4.3.7.81 | ScalarnpCtlGCPrint | read-write | optional | Used to Enable/Disable/Remove(Hide) the GC Print service. Disable = 0 Enable (Default) = 1 Remove = 2 If disable is specified and the device is registered for … |
| 1.3.6.1.4.1.11.2.4.3.8 | NodenpNpi | |||
| 1.3.6.1.4.1.11.2.4.3.8.3 | NodenpNpiPeripheralAttributeEntry | |||
| 1.3.6.1.4.1.11.2.4.3.8.3.2 | ScalarnpNpiPaeClass | read-only | current | The class assigned to the peripheral onto which this card is plugged. |
| 1.3.6.1.4.1.11.2.4.3.8.3.3 | ScalarnpNpiPaeIdentification | read-only | current | The Identification number of the peripheral. These values are defined in the MIO spec. DesignJet, PaintJet XL300, and DesignJet/600 peripherals will identify t… |
| 1.3.6.1.4.1.11.2.4.3.8.4 | NodenpNpiCardAttributeEntry | |||
| 1.3.6.1.4.1.11.2.4.3.8.4.2 | ScalarnpNpiCaeClass | read-only | current | The class of this network peripheral card. |
| 1.3.6.1.4.1.11.2.4.3.13 | NodenpPort | |||
| 1.3.6.1.4.1.11.2.4.3.13.1 | ScalarnpPortNumPorts | read-only | current | The number of peripheral interfaces supported by this device. |
| 1.3.6.1.4.1.11.2.4.3.15 | TablenpCRCTable | not-accessible | current | |
| 1.3.6.1.4.1.11.2.4.3.15.1 | RownpCRCEntry | not-accessible | current | |
| 1.3.6.1.4.1.11.2.4.3.15.1.1 | ColumnnpCRCIndex | read-only | current | |
| 1.3.6.1.4.1.11.2.4.3.15.1.2 | ColumnnpCRCText | read-only | current | |
| 1.3.6.1.4.1.11.2.4.3.15.1.3 | ColumnnpCRCChannel | read-only | current | |
| 1.3.6.1.4.1.11.2.4.3.16 | NodenpDhcp | |||
| 1.3.6.1.4.1.11.2.4.3.16.2 | ScalarnpDHCPserver | read-only | current | IP address of DHCP server that provided this unit with an IP address via the DHCP protocol. |
| 1.3.6.1.4.1.11.2.4.3.16.4 | ScalarnpDhcpFQDNBehavior | read-write | current | This object defines the FQDN behavior in Jetdirect. Set this to ( 0 ) - Present Jetdirect Behavior ( 1 ) - RFC 4702 compliant behavior |
| 1.3.6.1.4.1.11.2.4.3.18 | NodenpWeb | |||
| 1.3.6.1.4.1.11.2.4.3.18.12 | ScalarnpWebProxyServerId | read-write | current | IP address or hostname of web proxy server. |
| 1.3.6.1.4.1.11.2.4.3.18.13 | ScalarnpWebProxyServerPort | read-write | current | IP port of web proxy server |
| 1.3.6.1.4.1.11.2.4.3.18.14 | ScalarnpWebProxyUserName | read-write | current | Proxy web user identification |
| 1.3.6.1.4.1.11.2.4.3.18.15 | ScalarnpWebProxyUserPasswd | read-write | current | Proxy web user password |
| 1.3.6.1.4.1.11.2.4.3.18.17 | ScalarnpWebCheckACLforHTTP | read-write | current | Configure checking of HTTP web connections against Access Control List. (0) = Disable ACL checking (1) = Enable ACL checking |
| 1.3.6.1.4.1.11.2.4.3.20 | NodenpSecurity | |||
| 1.3.6.1.4.1.11.2.4.3.20.1 | ScalarnpSecurityDot1xServerAuthProtocols | read-write | current | HP print servers support secured network access via Extensible Authentication Protocol (EAP) on an IEEE 802.1X network. The IEEE 802.1X standard provides a por… |
| 1.3.6.1.4.1.11.2.4.3.20.2 | ScalarnpSecurityDot1xUsername | read-write | current | Username required by EAP/802.1x Authentication methods. |
| 1.3.6.1.4.1.11.2.4.3.20.3 | ScalarnpSecurityDot1xAuthServerId | read-write | current | Server ID relates to the Common Name that is returned in the subject of the Authentication Server Certificate and determines how print server should validate t… |
| 1.3.6.1.4.1.11.2.4.3.20.4 | ScalarnpSecurityPublicKey | read-only | current | The public key of a public/private key pair to be used by applications to set encrypted values. |
| 1.3.6.1.4.1.11.2.4.3.20.5 | ScalarnpSecurityDot11EncryptedDot11NetworkName | write-only | current | The encrypted network name (SSID). Use the npSecurityPublicKey to encrypt this value. Setting this object will cause the card to reconfigure. |
| 1.3.6.1.4.1.11.2.4.3.20.6 | ScalarnpSecurityEncryptedDot1xPassword | read-write | current | Password required by EAP/802.1x Authentication methods Use the npSecurityPublicKey (1.3.6.1.4.1.11.2.4.3.20.4.0) to encrypt this value using RSA public key enc… |
| 1.3.6.1.4.1.11.2.4.3.20.7 | TablenpSecurityDot11EncryptedWEPKeyTable | not-accessible | current | Encrypted interface to the WEP Keys. |
| 1.3.6.1.4.1.11.2.4.3.20.7.1 | RownpSecurityDot11EncryptedWEPKeyEntry | not-accessible | current | Each row of the table gives a WEP Key |
| 1.3.6.1.4.1.11.2.4.3.20.7.1.2 | ColumnnpSecurityDot11EncryptedWEPKey | write-only | current | The encrypted WEP Key value. Use the npSecurityDot11PublicKey to encrypt this value. Setting this object will cause the card to reconfigure. |
| 1.3.6.1.4.1.11.2.4.3.20.8 | ScalarnpSecurityDot11SignalStrength | read-only | current | A weighted average over time of the signal strength between the access point and the print server in infrastructure mode. Not applicable when in ad hoc mode. |
| 1.3.6.1.4.1.11.2.4.3.20.9 | TablenpSecurityDot11SSIDTable | not-accessible | current | List of discovered SSIDs. |
| 1.3.6.1.4.1.11.2.4.3.20.9.1 | RownpSecurityDot11SSIDEntry | not-accessible | current | Each row of the table gives a discovered SSID value. |
| 1.3.6.1.4.1.11.2.4.3.20.9.1.2 | ColumnnpSecurityDot11SSID | read-only | current | A discovered SSID value. |
| 1.3.6.1.4.1.11.2.4.3.20.10 | ScalarnpSecurityDot11SSIDTableNumEntries | read-only | current | Displays the number of discovered SSIDs in the SSID Table. |
| 1.3.6.1.4.1.11.2.4.3.20.11 | ScalarnpSecurityDot11SSLCertLoaded | read-only | current | Indicates if SSL certificate has been loaded. |
| 1.3.6.1.4.1.11.2.4.3.20.12 | ScalarnpSecurityDot11TLSCertLoaded | read-only | current | Indicates if TLS Trusted CA certificate has been loaded. |
| 1.3.6.1.4.1.11.2.4.3.20.13 | ScalarnpSecuritySnmpV3EncryptedUserName | write-only | current | The encrypted SNMPv3 User Name. Use the npSecurityPublicKey to encrypt this value. When setting this object, all three user account objects (npSecuritySnmpV3En… |
| 1.3.6.1.4.1.11.2.4.3.20.14 | ScalarnpSecuritySnmpV3AuthKeyPassPhrase | write-only | current | The encrypted SNMPv3 Authentication passphrase or key . Use the npSecurityPublicKey to encrypt this value. When setting this object, all three user account obj… |
| 1.3.6.1.4.1.11.2.4.3.20.15 | ScalarnpSecuritySnmpV3PrivKeyPassPhrase | write-only | current | The encrypted SNMPv3 Privacy passphrase or key. Use the npSecurityPublicKey to encrypt this value. When setting this object, all three user account objects (np… |
| 1.3.6.1.4.1.11.2.4.3.20.16 | ScalarnpSecurityDot11BSSID | read-only | current | The BSSID value (hardware address of the access point). |
| 1.3.6.1.4.1.11.2.4.3.20.17 | ScalarnpSecurityDot1xTunnelAuthBits | read-write | current | The Dot1x Tunnel Authentication Bits. Bitwise field with the followings bits: Default All bits cleared EAP MD5 1 EAP MSCHAP 2 EAP MSCHAPv2 4 MSCHAP 8 MSCHAPv2 … |
| 1.3.6.1.4.1.11.2.4.3.20.18 | ScalarnpSecurityDot1xIdentityCleartext | read-write | current | The Dot1x Identity in cleartext. |
| 1.3.6.1.4.1.11.2.4.3.20.19 | ScalarnpSecurityDot1xExactMatchServerId | read-write | current | This OID allows us to configure the �Require Exact Match� feature which indicates how common name from a successfully authenticated server is considered. F… |
| 1.3.6.1.4.1.11.2.4.3.20.20 | ScalarnpSecurityDot1xEncryptionStrength | read-write | current | Encryption strength determines the minimum strength of the SSL tunnel by determining what ciphers are advertised by the print server in the TLS Client Hello pa… |
| 1.3.6.1.4.1.11.2.4.3.20.21 | ScalarnpSecurityCertBuff | read-only | current | A 512 byte buffer of the print server certificate as indexed by npSecurityCertBuffIndex. |
| 1.3.6.1.4.1.11.2.4.3.20.22 | ScalarnpSecurityCertBuffIndex | read-write | current | Indicates the index of the 512 byte block of the print server certificate to load into npSecurityCertBuff. |
| 1.3.6.1.4.1.11.2.4.3.20.23 | ScalarnpSecuritySslRedirection | read-write | current | Setting this object causes the SSL redirection connection to be enabled or disabled. |
| 1.3.6.1.4.1.11.2.4.3.20.24 | ScalarnpSecurityReset | read-write | current | Setting this object causes security object to reset bact to the defaults. |
| 1.3.6.1.4.1.11.2.4.3.20.25 | ScalarnpSecurityWebSpiEnable | read-write | current | This object enables/disables the Embedded Web Simple Printer Install feature. |
| 1.3.6.1.4.1.11.2.4.3.20.26 | ScalarnpSecurityDot11WEPStrength | read-only | current | Indicates the encryption strength of the WEP keys. |
| 1.3.6.1.4.1.11.2.4.3.20.27 | ScalarnpSecurityServicesSupported | read-only | current | BITWISE indication of the security services this device supports. The following bits are defined: MD5 (0) TLS (1) TTLS (2) LEAP (3) PEAP (4) Reserved (5 - 15) … |
| 1.3.6.1.4.1.11.2.4.3.20.28 | ScalarnpSecurityDot11Encryption | read-write | current | 802.11 encryption method currently enabled. The following values are defined: NONE (0x00) SSN/WEP (0x01) TKIP (0x02) AES (0x03) AUTO (0x04) Reserved (5 - 31) I… |
| 1.3.6.1.4.1.11.2.4.3.20.29 | ScalarnpSecurityDot11MulticastCipher | read-write | current | BITWISE indication of the multicast cipher method currently enabled. At minimum, one bit must be set. The following bits are defined: WEP (0) WPA (1) Reserved … |
| 1.3.6.1.4.1.11.2.4.3.20.34 | ScalarnpSecurityDot11BeaconTableNumEntries | read-only | current | Displays the number of discovered SSIDs in the DOT11 Beacon Table. |
| 1.3.6.1.4.1.11.2.4.3.20.35 | ScalarnpSecurityDot11OpenSSIDEnabled | read-only | current | Indicates if the Open SSID is enabled (Spirit-only). |
| 1.3.6.1.4.1.11.2.4.3.20.36 | ScalarnpSecurityDot11EncryptedWPAConfigPSKPassPhrase | write-only | current | The encrypted WPA Config PSK PassPhrase. Use the npSecurityPublicKey to encrypt this value |
| 1.3.6.1.4.1.11.2.4.3.20.37 | ScalarnpSecurityDot11DataRate | read-only | current | Current wireless network data rate |
| 1.3.6.1.4.1.11.2.4.3.20.38 | ScalarnpSecurityDot11ScanComplete | read-write | current | Used to control scan for SSIDs in the wireless network. Set to false to initiate a scan. A value of true indicates the completion of the scan |
| 1.3.6.1.4.1.11.2.4.3.20.39 | ScalarnpSecurityDot11RoamThreshold | read-write | current | Used to control roaming by the wireless radio. The radio on the print server will roam or try to find an access point with a stronger signal once the signal st… |
| 1.3.6.1.4.1.11.2.4.3.20.40 | ScalarnpSecuritySslEncryptionStrength | read-write | current | The SSL Encryption Strength. Setting to Low, Medium or High decides the set of Cipher Suites that would be supported by the device. |
| 1.3.6.1.4.1.11.2.4.3.20.41 | ScalarnpSecurityDot11InstantVerification | read-write | current | Enable and disable wireless instant verification. (0) = Disable (1) = Enable |
| 1.3.6.1.4.1.11.2.4.3.20.42 | ScalarnpSecurityDot11DynamicEncryption | read-write | current | WPA mode. (0x00) = NONE (0x01) = BASIC (0x02) = WPA (0x03) = WPA2 (0x04) = AUTO |
| 1.3.6.1.4.1.11.2.4.3.20.43 | ScalarnpSecurityDot11LinkAuthentication | read-write | current | DOT11 Link Authentication modes. (1) = OPEN (2) = SHARED-KEY (128) = LEAP (143) = AUTO We can set the Link Authentication using the object dot11AuthenticationA… |
| 1.3.6.1.4.1.11.2.4.3.20.44 | ScalarnpSecuritySnmpV3AuthAlgorithm | read-write | current | Indicates the Authentication Algorithm used. It can have the value MD5 or SHA-1. This key will have a default value set to MD5. The following values are define… |
| 1.3.6.1.4.1.11.2.4.3.20.45 | ScalarnpSecuritySnmpV3PrivAlgorithm | read-write | current | Indicates the Privacy Algorithm used. It can have the value DES or AES-128. This key will have a default value set to DES. The following values are defined: DE… |
| 1.3.6.1.4.1.11.2.4.3.20.51 | ScalarnpSecurityWirelessDirectEncryptionMethod | read-write | current | This is used to select the encryption protocol in Wireless Direct Mode. The following values are defined: No Security ( 1 ) WPA ( 2 ) |
| 1.3.6.1.4.1.11.2.4.3.20.55 | ScalarnpSecurityWirelessDirectEncryptedPassPhrase | write-only | current | The WPA2 Passphrase or pre-shared key for secure Wireless Direct. The values allowed are 8 to 63 printable ASCII characters for passphrase or a 64 character he… |
| 1.3.6.1.4.1.11.2.4.3.20.57 | ScalarnpSecurityDot1xFailSafe | read-write | current | After configuring 802.1x on the printer and switching it over to a secured network, if authentication is successful printer retains connectivity and if it fail… |
| 1.3.6.1.4.1.11.2.4.3.20.61 | ScalarnpSecurityIppAuthentication | read-write | current | IPP Authentication is a feature which provides 'HTTP Basic Authentication' for IPP Print-Jobs. Use this OID to Enable/Disable IPP Authentication. 0 - Disable I… |
| 1.3.6.1.4.1.11.2.4.3.20.62 | ScalarnpSecurityIppAuthUsername | read-write | current | IPP Authentication is a feature which provides 'HTTP Basic Authentication' for IPP Print-Jobs. Use this OID to configure the IPP Authentication Username. Strin… |
| 1.3.6.1.4.1.11.2.4.3.20.63 | ScalarnpSecurityIppEncryptedAuthPassword | read-write | current | IPP Authentication is a feature which provides 'HTTP Basic Authentication' for IPP Print-Jobs. Use this OID to configure the IPP Authentication Password. Strin… |
| 1.3.6.1.4.1.11.2.4.3.22 | NodeinetTrap | |||
| 1.3.6.1.4.1.11.2.4.3.22.1 | NodeinetTrapDestination | |||
| 1.3.6.1.4.1.11.2.4.3.22.1.1 | ScalarinetTrapDestinationNum | read-only | current | Total number of ACTIVE rows in the inetTrapDestination table. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2 | TableinetTrapDestinationTable | not-accessible | current | List of inetTrap destinations to which the agent sends traps. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1 | RowinetTrapDestinationEntry | not-accessible | current | Entries are inetAddress Specific sequence of trap destination parameters. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.1 | ColumninetTrapRowIndex | read-only | current | Row Index of the inetTrapDestination table |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.2 | ColumninetTrapRowStatus | read-write | current | Individual Row Status 1 - Row is Active - Row is activated and ready. 2 - Not-In-Service - Row is suspended. 3 - Not Ready - Row is not activated and still nee… |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.3 | ColumninetTrapAddressType | read-write | current | Protocol family for trap. Possible values: ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by … |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.4 | ColumninetTrapAddress | read-write | current | IPv4/IPv6/FQDN address of trap destination node. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.5 | ColumninetTrapPort | read-write | current | Port number of the inetTrap Destination to which the trap is sent. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.6 | ColumninetTrapCommunityName | read-write | current | Trap community name specified in the trap packet. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.7 | ColumninetTrapVersion | read-write | current | Trap version, one of the following 0 = snmpV1 1 = snmpV2 3 = Inform Default is 1 = snmpV2. This value remains persistent through a powercycle. |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.8 | ColumninetTrapStyle | read-write | current | This OID is read-write. If the user wants to receive only the PML traps, then trapStyle can be set to 1. If the user wants to receive only APS and General or N… |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.9 | ColumninetTrapPMLOids | read-write | current | This OID is a read-write. This will have tokens of PML trappable OIDs. Each token (OID) will be separated by a semi-colon. If a trap destination entry is regis… |
| 1.3.6.1.4.1.11.2.4.3.22.1.2.1.10 | ColumninetTrapErrorValue | read-only | current | Gives the error value in case if the server is not able to send the traps to the configured trapDestination entry. It will be set to below defined error values… |
| 1.3.6.1.4.1.11.2.4.3.22.1.3 | ScalarinetTrapTest | write-only | current | Causes agent to send an snmp trap to hosts registered in the trap destination table. Value specified will be used as the specific trap id. |
| 1.3.6.1.4.1.11.2.4.3.22.1.4 | ScalarinetTrapFilterDelay | read-write | current | The purpose of the trap filter feature is to prevent multiple traps of the same specificTrapId to be sent within a short period of time. This object assigns th… |
| 1.3.6.1.4.1.11.2.4.3.22.1.5 | ScalarinetTrapBaseTimeout | read-write | current | Applicable only if trapVersion is set to Inform. Units are 1/10 second intervals. Default is 2 corresponding to 200 milliseconds. This value corresponds to the… |
| 1.3.6.1.4.1.11.2.4.3.22.1.6 | ScalarinetTrapRetryNum | read-write | current | Applicable only if trapVersion is set to Inform. This is the maximum number of inform retries that will be sent to this destination. Retries are sent if no inf… |
| 1.3.6.1.4.1.11.2.4.3.22.1.7 | ScalarinetTrapFQDNResolution | read-write | current | The purpose of this field is to configure various options for resolving FQDN. If configured as 1 - then FQDN names will be resolved for IPv4 addresses only If … |
| 1.3.6.1.4.1.11.2.4.3.22.1.8 | ScalarinetTrapFQDNMultipleAddressBehavior | read-write | current | 1 - Send traps to the first resolved address 2 - Send traps to all resolved address. |
| 1.3.6.1.4.1.11.2.4.3.22.1.9 | ScalarinetTrapUseDNSCache | read-write | current | Depending upon the value of this field resolution of FQDN will happen everytime when a trap is sent. |
| 1.3.6.1.4.1.11.2.13 | Nodetrap | |||
| 1.3.6.1.4.1.11.2.13.1 | NodetrapDest | |||
| 1.3.6.1.4.1.11.2.13.1.1 | ScalartrapDestinationNum | read-only | current | The number of trap destinations. |
| 1.3.6.1.4.1.11.2.13.1.2 | TabletrapDestinationTable | not-accessible | current | Protocol specific list of destinations to which the agent sends traps. |
| 1.3.6.1.4.1.11.2.13.1.2.1 | RowtrapDestinationEntry | not-accessible | current | Entries are a protocol specific sequence of trap destination parameters. |
| 1.3.6.1.4.1.11.2.13.1.3 | ScalartrapTest | read-write | current | Causes agent to send an snmp trap to hosts registered in the trap destination table. Value specified will be used as the specific trap id. |
| 1.3.6.1.4.1.11.2.13.1.4 | ScalartrapSource | read-only | current | Sets the agent internal source for traps. Possibilities are as follows: 0 = ALL_TRAPS_ON 1 = ASYNC_PERIPHERAL_STATUS traps only 2 = proprietary PML traps only … |
| 1.3.6.1.4.1.11.2.13.1.5 | ScalartrapFilterDelay | read-write | current | The purpose of the trap filter feature is to prevent multiple traps of the same specificTrapId to be sent within a short period of time. This object assigns th… |
| 1.3.6.1.4.1.11.2.13.1.6 | ScalartrapFQDNNum | read-only | current | Number of trapFQDNTable rows. |
| 1.3.6.1.4.1.11.2.13.1.7 | TabletrapFQDNTable | not-accessible | current | The trap destination entries can be mapped to destination's FQDN name in this table. |
| 1.3.6.1.4.1.11.2.13.1.7.1 | RowtrapFQDNEntry | not-accessible | current | An FQDN destination entry indexed by the destination's IP address. |
| 1.3.6.1.4.1.11.2.13.1.7.1.1 | ColumntrapIPAddress | read-only | current | The trap destination IP address. |
| 1.3.6.1.4.1.11.2.13.1.7.1.2 | ColumntrapFQDN | read-write | current | The trap destination's FQDN. This will be resolved to IP address(es) at trap destination time. |
| 1.3.6.1.4.1.11.2.15 | NodesnmpAccess | |||
| 1.3.6.1.4.1.11.2.15.1 | Nodecommunity | |||
| 1.3.6.1.4.1.11.2.15.1.1 | ScalarsetCommunityName | read-write | current | This object controls access of snmp read-write requests. Factory default configuration provides authentication of incoming packets with community names: intern… |
| 1.3.6.1.4.1.11.2.15.1.2 | ScalargetCommunityName | read-write | current | This object controls access of snmp read requests. Factory default configuration provides authentication of incoming packets with community names: internal and… |