NB30MIB
143 objects
No module-level DESCRIPTION found.
Imported Objects
| IRM-OIDS | nb30Rev1 |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.1.6.12.1 | Nodenb30Device | |||
| 1.3.6.1.4.1.52.1.6.12.1.1 | Scalarnb30DeviceDisableBdg | read-write | mandatory | Indicates if the bridge will be disabled. |
| 1.3.6.1.4.1.52.1.6.12.1.2 | Scalarnb30DeviceRestoreSettings | read-write | mandatory | Restore the following settings to their default values: Bridge Name to CABLETRON REMOTE BRIDGE, Location to LOCAL, Enet Port 1 Name to ETHERNET PORT 1, Enet Po… |
| 1.3.6.1.4.1.52.1.6.12.1.3 | Scalarnb30DeviceBdgName | read-write | mandatory | The user-defined name (up to 32 characters long) of the bridge. The default bridge name is CABLETRON REMOTE BRIDGE. |
| 1.3.6.1.4.1.52.1.6.12.1.4 | Scalarnb30DeviceNumPorts | read-only | mandatory | The number of ports present on the bridge. |
| 1.3.6.1.4.1.52.1.6.12.1.5 | Scalarnb30DeviceType | read-only | mandatory | The type of bridge, NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.6 | Scalarnb30DeviceVersion | read-only | mandatory | The release version of the firmware installed in the bridge. |
| 1.3.6.1.4.1.52.1.6.12.1.7 | Scalarnb30DeviceLocation | read-write | mandatory | The user-defined name (up to 14 characters long) to indicate the location of the bridge on the network. The default location name is LOCAL. |
| 1.3.6.1.4.1.52.1.6.12.1.8 | Scalarnb30DeviceStatus | read-only | mandatory | The status of the bridge, ON-LINE, STAND BY or DISABLED. |
| 1.3.6.1.4.1.52.1.6.12.1.9 | Scalarnb30DeviceRestartBdg | read-write | mandatory | Force the bridge to undergo a software reset. |
| 1.3.6.1.4.1.52.1.6.12.1.10 | Scalarnb30DeviceFrFwds | read-only | mandatory | The number of frames forwarded by the bridge. |
| 1.3.6.1.4.1.52.1.6.12.1.11 | Scalarnb30DeviceFrRxs | read-only | mandatory | The number of frames received by the bridge. |
| 1.3.6.1.4.1.52.1.6.12.1.12 | Scalarnb30DeviceFrFlts | read-only | mandatory | The number of frames filtered by the bridge. |
| 1.3.6.1.4.1.52.1.6.12.1.13 | Scalarnb30DeviceErrs | read-only | mandatory | The total number of network errors that have occurred. |
| 1.3.6.1.4.1.52.1.6.12.1.14 | Scalarnb30DeviceNumRestarts | read-only | mandatory | The number of times the bridge has been powered up or restarted. |
| 1.3.6.1.4.1.52.1.6.12.1.15 | Scalarnb30DeviceTypeFiltering | read-write | mandatory | The type of filtering to be performed by the bridge. The default is IEEE 802.1. |
| 1.3.6.1.4.1.52.1.6.12.1.16 | Scalarnb30DeviceSTAProtocol | read-write | mandatory | The spanning tree algorithm under which the bridge is operating. The selections are as follows: - IEEE 802.1 compliant spanning tree algorithm environment (802… |
| 1.3.6.1.4.1.52.1.6.12.1.17 | Scalarnb30DeviceBridgeID | read-only | mandatory | The unique identifier of the bridge. The first two bytes of the identifier are the bridge priority and the last six bytes are the Ethernet address. |
| 1.3.6.1.4.1.52.1.6.12.1.18 | Scalarnb30DeviceTopChgCnts | read-only | mandatory | The number of times the bridge's Topology Change Flag has been changed since the bridge was powered up or initialized. |
| 1.3.6.1.4.1.52.1.6.12.1.19 | Scalarnb30DeviceTimeTopChg | read-only | mandatory | The time in seconds that has elapsed since the bridge's Topology Change Flag last recorded the value of a topology change. |
| 1.3.6.1.4.1.52.1.6.12.1.20 | Scalarnb30DeviceTopChg | read-only | mandatory | Indicates if a bridge topology change is in progress. |
| 1.3.6.1.4.1.52.1.6.12.1.21 | Scalarnb30DeviceRootCost | read-only | mandatory | The cost of the path to the root from this bridge. |
| 1.3.6.1.4.1.52.1.6.12.1.22 | Scalarnb30DeviceRootPort | read-only | mandatory | The port identifier for the port which offers the lowest cost path to the root, i.e. that port for which the sum of the values of the designated cost and path … |
| 1.3.6.1.4.1.52.1.6.12.1.23 | Scalarnb30DeviceDesigRoot | read-only | mandatory | The unique identifier of the bridge recorded as the root. |
| 1.3.6.1.4.1.52.1.6.12.1.24 | Scalarnb30DeviceMaxAge | read-only | mandatory | The maximum age of received protocol information before it is discarded. |
| 1.3.6.1.4.1.52.1.6.12.1.25 | Scalarnb30DeviceHoldTime | read-only | mandatory | The minimum time period elapsing between the transmission of configuration BPDU's through a given bridge port. |
| 1.3.6.1.4.1.52.1.6.12.1.26 | Scalarnb30DeviceFwdDly | read-only | mandatory | The time spent in the listening state while moving from the blocking state to the learning state, or the time spent in the learning state while moving from the… |
| 1.3.6.1.4.1.52.1.6.12.1.27 | Scalarnb30DeviceHelloTime | read-only | mandatory | The time interval between the transmission of Configuration BPDU's by a bridge which is attempting to become the root or is the root. |
| 1.3.6.1.4.1.52.1.6.12.1.28 | Scalarnb30DeviceBdgFwdDly | read-write | mandatory | The value of the forward delay parameter when the bridge is the root or is attempting to become the root. A time of 4 to 30 seconds is allowed. The default is … |
| 1.3.6.1.4.1.52.1.6.12.1.29 | Scalarnb30DeviceBdgMaxAge | read-write | mandatory | The value of the Max Age parameter when the bridge is the root or is attempting to become the root. A time of 6 to 40 seconds is allowed. The default is 20 sec… |
| 1.3.6.1.4.1.52.1.6.12.1.30 | Scalarnb30DeviceBdgHello | read-write | mandatory | The value of the Hello Time parameter when the bridge is the root or is attempting to become the root. A time of 1 to 10 seconds is allowed. The default is 2 s… |
| 1.3.6.1.4.1.52.1.6.12.1.31 | Scalarnb30DeviceBdgPriority | read-write | mandatory | Used in the spanning tree for priority comparisons. Allowed range is 0 through FFFF. The default is 8000. |
| 1.3.6.1.4.1.52.1.6.12.1.32 | Scalarnb30DeviceResetCounts | read-write | mandatory | Reset all counters to zero. |
| 1.3.6.1.4.1.52.1.6.12.1.33 | Scalarnb30DeviceUptime | read-only | mandatory | The time, in seconds, that has elapsed since the bridge was last reset or initialized. |
| 1.3.6.1.4.1.52.1.6.12.1.34 | Scalarnb30DeviceRootSwitch | read-only | mandatory | The status of the Root switch on the front panel of the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.35 | Scalarnb30DeviceFwdBroadcast | read-only | mandatory | The status of the Forward Broadcast switch on the front panel of the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.36 | Scalarnb30DeviceConfigSw1 | read-only | mandatory | The status of Config switch 1 on the back panel of the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.37 | Scalarnb30DeviceConfigSw2 | read-only | mandatory | The status of Config switch 2 on the back panel of the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.38 | Scalarnb30DeviceConfigSw3 | read-only | mandatory | The status of Config switch 3 on the back panel of the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.39 | Scalarnb30DeviceConfigSw4 | read-only | mandatory | The status of Config switch 4 on the back panel of the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.40 | Scalarnb30DevicePortActive | read-only | mandatory | The Port number which is acting as the online Ethernet Port on the NB30. |
| 1.3.6.1.4.1.52.1.6.12.1.41 | Scalarnb30DeviceDefPort | read-write | mandatory | The Port number which is Default Ethernet Port on the NB30 at power up. |
| 1.3.6.1.4.1.52.1.6.12.1.42 | Scalarnb30DeviceRedEnable | read-write | mandatory | The state of the Redundancy Enable Flag. |
| 1.3.6.1.4.1.52.1.6.12.2 | Nodenb30Dsx | |||
| 1.3.6.1.4.1.52.1.6.12.2.1 | Scalarnb30DsxLoopUp | read-write | mandatory | The loop up command for the DSX-1 Remote Interface. |
| 1.3.6.1.4.1.52.1.6.12.2.2 | Scalarnb30DsxLoopDn | read-write | mandatory | The loop down command for the DSX-1 Remote Interface. |
| 1.3.6.1.4.1.52.1.6.12.2.3 | Scalarnb30DsxLoopSt | read-only | mandatory | The loop status for the DSX-1 Remote Interface. |
| 1.3.6.1.4.1.52.1.6.12.2.4 | Scalarnb30DsxLoopPattern | read-write | mandatory | The loop test pattern for the DSX-1 Remote Interface. |
| 1.3.6.1.4.1.52.1.6.12.3 | Nodenb30DsxChannel | |||
| 1.3.6.1.4.1.52.1.6.12.3.1 | Tablenb30DsxChannelTable | not-accessible | mandatory | NB30 DSX-1 Remote Port Channelization Table |
| 1.3.6.1.4.1.52.1.6.12.3.1.1 | Rownb30DsxEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.3.1.1.1 | Columnnb30DsxChannelControl | read-write | mandatory | Disable the DSX-1 Channel. |
| 1.3.6.1.4.1.52.1.6.12.3.1.1.2 | Columnnb30DsxChannelId | read-write | mandatory | The channel number for this entry. |
| 1.3.6.1.4.1.52.1.6.12.4 | Nodenb30Port | |||
| 1.3.6.1.4.1.52.1.6.12.4.1 | Tablenb30PortTable | not-accessible | mandatory | Bridge Port information table |
| 1.3.6.1.4.1.52.1.6.12.4.1.1 | Rownb30PortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.1 | Columnnb30PortAddress | read-only | mandatory | The Ethernet address of the port. Instance of 1 represents the local Ethernet address, instance of 2 represents the remote Ethernet address. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.2 | Columnnb30PortName | read-write | mandatory | The user-defined name (up to 32 characters long) assigned to the port. The default Enet port 1 name is ETHERNET PORT 1 and the default Enet Port 2 name is ETHE… |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.3 | Columnnb30PortType | read-only | mandatory | The IEEE specification the port meets, e.g. 802.3. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.4 | Columnnb30PortStatus | read-only | mandatory | The status in which the port is operating. The status messages for Ports 1 and 2 are: OFF - The port is off, due to a failed network interface chip associated … |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.5 | Columnnb30PortNetName | read-write | mandatory | The user-defined name (up to 32 characters long) assigned to a network segment connected to the port. The default network name for Port 1 is LAN_1 and the defa… |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.6 | Columnnb30PortFrRxs | read-only | mandatory | The number of frames received at the specified port. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.7 | Columnnb30PortDisInbounds | read-only | mandatory | The total number of valid frames that were received at the port but then discarded by the bridge in the forwarding process. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.8 | Columnnb30PortFwdOutbs | read-only | mandatory | The number of frames forwarded successfully to the appropriate port. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.9 | Columnnb30PortDisLOBs | read-only | mandatory | The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.10 | Columnnb30PortDisTDEs | read-only | mandatory | The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was … |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.11 | Columnnb30PortCollisions | read-only | mandatory | The number of collisions that have occurred on the network at the specified port. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.12 | Columnnb30PortTxAborts | read-only | mandatory | The number of transmissions that have been aborted due to excessive collisions (over 16 attempts to transmit the same packet). |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.13 | Columnnb30PortOowCollisions | read-only | mandatory | The number of collisions out of the standard collision window (51.2 uS). This indicates a network problem. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.14 | Columnnb30PortCRCErrs | read-only | mandatory | The number of packets detected with Cyclical Redundancy Check failures. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.15 | Columnnb30PortFrAlignErrs | read-only | mandatory | The number of errors due to misaligned packets. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.16 | Columnnb30PortPriority | read-write | mandatory | The part of the port identifier which is used with the spanning tree algorithm when determining which port in a LAN segment has priority. The default is 80. Ap… |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.17 | Columnnb30PortState | read-only | mandatory | The current state of the port, DISABLED, LISTENING, LEARNING, FORWARDING or BLOCKING. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always re… |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.18 | Columnnb30PortPathCost | read-write | mandatory | The contributory cost of the applicable port to the overall cost of the path when the specified port is the root port. Allowable range is 1 to 65535. The defau… |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.19 | Columnnb30PortDesigCost | read-only | mandatory | The cost of the path of this port to the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local… |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.20 | Columnnb30PortDesigBrdg | read-only | mandatory | The network address of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always … |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.21 | Columnnb30PortDesigPort | read-only | mandatory | The port identifier of the bridge port believed to be the designated port for the LAN associated with the port. Applies to the LOCAL and REMOTE Ethernet ports … |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.22 | Columnnb30PortTopChgAck | read-only | mandatory | The value of the topology change acknowledgement flag in the next configuration BPDU to be transmitted on the associated port. Applies to the LOCAL and REMOTE … |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.23 | Columnnb30PortDesigRoot | read-only | mandatory | The unique bridge identifier of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance … |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.24 | Columnnb30PortOversizePkts | read-only | mandatory | The number of packets received at the indicated NB30 Port that were greater than the IEEE 802.3 maximum Ethernet frame size of 1518 bytes. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.25 | Columnnb30PortFrFiltereds | read-only | mandatory | The number of frames received at the indicated port that were filtered by the bridge. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.26 | Columnnb30PortPollAddress | read-write | mandatory | The Poll Address that will be used by the Redundant Port Algorithm on the NB30. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.27 | Columnnb30PortPollInterval | read-write | mandatory | The Poll Interval used by the Redundant Port Algorithm on the NB30. Valid range is 1 - 30 seconds. |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.28 | Columnnb30PortMaxRetry | read-write | mandatory | The Max number of retries for the Redundant Port Algorithm on the NB30. Valid range is 2 - 99 retries |
| 1.3.6.1.4.1.52.1.6.12.4.1.1.29 | Columnnb30PortId | read-only | mandatory | The port number for this entry. |
| 1.3.6.1.4.1.52.1.6.12.5 | Nodenb30RemPort | |||
| 1.3.6.1.4.1.52.1.6.12.5.1 | Tablenb30RemPortTable | not-accessible | mandatory | Bridge Remote Port information table |
| 1.3.6.1.4.1.52.1.6.12.5.1.1 | Rownb30RemPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.1 | Columnnb30RemPortName | read-write | mandatory | The user-defined name assigned to the remote port. The default Remote port name is REMOTE PORT. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.2 | Columnnb30RemPortType | read-only | mandatory | The Electrical interface specification the port meets, e.g. DSX-1, V.35. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.3 | Columnnb30RemPortStatus | read-only | mandatory | The status in which the remote port is operating. The status messages for the Remote Port are: NO EXT CLOCK DCE NOT READY / NO DM DCE NOT READY / NO CTS LINK O… |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.4 | Columnnb30RemPortNetName | read-write | mandatory | The user-defined name assigned to a wide area segment connected to the remote port. The default network name for Remote Port is REMOTE LINK. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.5 | Columnnb30RemPortFrRxs | read-only | mandatory | The number of frames received at the remote port. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.6 | Columnnb30RemPortFwdOutbs | read-only | mandatory | The number of frames forwarded successfully to the remote port. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.7 | Columnnb30RemPortDisLOBs | read-only | mandatory | The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.8 | Columnnb30RemPortDisTDEs | read-only | mandatory | The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was … |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.9 | Columnnb30RemPortCRCErrs | read-only | mandatory | The number of packets detected with Cyclical Redundancy Check failures. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.10 | Columnnb30RemPortFrAlErrs | read-only | mandatory | The number of errors due to misaligned packets. |
| 1.3.6.1.4.1.52.1.6.12.5.1.1.11 | Columnnb30RemPortId | read-only | mandatory | The remote port ID, there is only a single port which is identified as 0. |
| 1.3.6.1.4.1.52.1.6.12.6 | Nodenb30FilterDB | |||
| 1.3.6.1.4.1.52.1.6.12.6.1 | Nodenb30AcqDB | |||
| 1.3.6.1.4.1.52.1.6.12.6.1.1 | Scalarnb30AcqTotalEntries | read-only | mandatory | The total number of entries in the acquired database. |
| 1.3.6.1.4.1.52.1.6.12.6.1.2 | Scalarnb30AcqMaxEntries | read-only | mandatory | The maximum number of entries allowed in the acquired database 8191 entries. |
| 1.3.6.1.4.1.52.1.6.12.6.1.3 | Scalarnb30AcqStaticEntries | read-only | mandatory | The number of addresses added to the Acquired database by the user or network manager. |
| 1.3.6.1.4.1.52.1.6.12.6.1.4 | Scalarnb30AcqDynamicEntries | read-only | mandatory | The number of entries that have been accumulated in the Acquired database through the bridge's learning process. |
| 1.3.6.1.4.1.52.1.6.12.6.1.5 | Scalarnb30AcqDynAgeTime | read-write | mandatory | The length of time allowed for a dynamic entry in the acquired database to be inactive before it is dropped from the database. A time from 10 - 1,000,000 secon… |
| 1.3.6.1.4.1.52.1.6.12.6.1.6 | Scalarnb30AcqEraseDatabase | read-write | mandatory | Set to one to erase all entries in the acquired database. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7 | Tablenb30AcqDBTable | not-accessible | mandatory | Aquired database entrys table |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1 | Rownb30AcqDBEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.1 | Columnnb30AcqCreateFilter | read-write | mandatory | Add an entry to the acquired database to filter packets entering port 1 if those packets are destined for the specified address. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.2 | Columnnb30AcqCreateForward | read-write | mandatory | Add an entry to the acquired database to forward packets entering port 1 to the remote port if those packets are destined for the specified address. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.3 | Columnnb30AcqDeleteFilter | read-write | mandatory | Delete an entry from the acquired database. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.4 | Columnnb30AcqFilterType | read-only | mandatory | Display the entry type, STATIC or DYNAMIC. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.5 | Columnnb30AcqFilterAction | read-only | mandatory | The action to be taken for packets entering port 1. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.6 | Columnnb30AcqSourceAddress | read-only | mandatory | The source address of this acquired database entry, i.e. the instance. |
| 1.3.6.1.4.1.52.1.6.12.6.1.7.1.7 | Columnnb30AcqMacAddress | read-only | mandatory | The MAC address for the specific entry. |
| 1.3.6.1.4.1.52.1.6.12.6.2 | Nodenb30PermDB | |||
| 1.3.6.1.4.1.52.1.6.12.6.2.1 | Scalarnb30PermMaxEntries | read-only | mandatory | The maximum number of entries allowed in the permanent database 2047 entries. |
| 1.3.6.1.4.1.52.1.6.12.6.2.2 | Scalarnb30PermCurrentEntries | read-only | mandatory | The number of entries currently recorded in the bridge's permanent database. |
| 1.3.6.1.4.1.52.1.6.12.6.2.3 | Scalarnb30PermEraseDatabase | read-write | mandatory | Erase all entries in the permanent database. |
| 1.3.6.1.4.1.52.1.6.12.6.2.4 | Tablenb30PermDBTable | not-accessible | mandatory | Aquired database entrys table |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1 | Rownb30PermDBEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.1 | Columnnb30PermCreateFilter | read-write | mandatory | Add an entry to the permanent database to filter packets entering port 1 if those packets are destined for the specified address. |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.2 | Columnnb30PermCreateForward | read-write | mandatory | Add an entry to the permanent database to forward packets entering port 1 to the remote port if those packets are destined for the specified address. |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.3 | Columnnb30PermDeleteEntry | read-write | mandatory | Delete an entry from the permanent database. |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.4 | Columnnb30PermFilterType | read-only | mandatory | Display the entry type, STATIC . |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.5 | Columnnb30PermFilterAction | read-only | mandatory | The action taken on packets entering port 1. |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.6 | Columnnb30PermSourceAddress | read-only | mandatory | The source address in this permanent database entry, i.e. the instance. |
| 1.3.6.1.4.1.52.1.6.12.6.2.4.1.7 | Columnnb30PermDBMacAddress | read-only | mandatory | The specific MAC address for this entry. |
| 1.3.6.1.4.1.52.1.6.12.6.3 | Nodenb30SpecDB | |||
| 1.3.6.1.4.1.52.1.6.12.6.3.1 | Scalarnb30SpecNumEntries | read-only | mandatory | The number of filters in the special database. |
| 1.3.6.1.4.1.52.1.6.12.6.3.2 | Scalarnb30SpecMaxEntries | read-only | mandatory | The maximum number of filters the special database can contain. |
| 1.3.6.1.4.1.52.1.6.12.6.3.3 | Scalarnb30SpecNextFilterNum | read-only | mandatory | The number of the next available filter that can be added to the special database. This OID will return a 255 if the database is full |
| 1.3.6.1.4.1.52.1.6.12.6.3.4 | Tablenb30SpecDBTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1 | Rownb30SpecDBEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.1 | Columnnb30SpecEnable | read-write | mandatory | Enable or disable the filter. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.2 | Columnnb30SpecPort1 | read-write | mandatory | Set port 1 to filter or forward packets. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.3 | Columnnb30SpecDestAddress | read-write | mandatory | Set the special database to filter packets with a specific destination address. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.4 | Columnnb30SpecSrcAddress | read-write | mandatory | Set the special database to filter packets with a specific source address. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.5 | Columnnb30SpecType | read-write | mandatory | Set the special database to filter packets with a specific type field. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.6 | Columnnb30SpecDataField | read-write | mandatory | Set the special database to filter packets based on the first sixteen bytes of data in the packet. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.7 | Columnnb30SpecDeleteFilter | read-write | mandatory | Delete a filter from the special database. |
| 1.3.6.1.4.1.52.1.6.12.6.3.4.1.8 | Columnnb30SpecDbFilterNumber | read-only | mandatory | The specific special data base filter number. |