NGDSL-LINE-MIB
353 objects
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines. Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1 am1] and [G.997.1 am2]. Note that the revised ITU-T G.997.1 standard refers also to next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of this document. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC XXXX: see the RFC itself for full legal notices.
Imported Objects
| HC-PerfHist-TC-MIB | HCPerfIntervalThreshold HCPerfTimeElapsed |
| IF-MIB | ifIndex |
| NGDSL-LINE-TC-MIB MISSING | Adsl2ChAtmStatus Adsl2ChPtmStatus Adsl2ConfPmsForce Adsl2Direction Adsl2InitResult Adsl2LastTransmittedState Adsl2LConfProfPmMode Adsl2LdsfResult Adsl2LineLdsf Adsl2LineStatus Adsl2MaxBer Adsl2OperationModes Adsl2PowerMngState Adsl2PsdMaskDs Adsl2PsdMaskUs Adsl2RaMode Adsl2RfiDs Adsl2ScMaskDs Adsl2ScMaskUs Adsl2SymbolProtection Adsl2TransmissionModeType Adsl2Tssi Adsl2Unit |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE transmission Unsigned32 |
| SNMPv2-TC | RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10 | IdentityngdslMIB | This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managin… | ||
| 1.3.6.1.2.1.10.1 | Nodeadsl2 | |||
| 1.3.6.1.2.1.10.1.0 | Nodeadsl2Notifications | |||
| 1.3.6.1.2.1.10.1.0.1 | Notificationadsl2LinePerfFECSThreshAtuc | current | This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.2 | Notificationadsl2LinePerfFECSThreshAtur | current | This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.3 | Notificationadsl2LinePerfESThreshAtuc | current | This notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.4 | Notificationadsl2LinePerfESThreshAtur | current | This notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.5 | Notificationadsl2LinePerfSESThreshAtuc | current | This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.6 | Notificationadsl2LinePerfSESThreshAtur | current | This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.7 | Notificationadsl2LinePerfLOSSThreshAtuc | current | This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.8 | Notificationadsl2LinePerfLOSSThreshAtur | current | This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.9 | Notificationadsl2LinePerfUASThreshAtuc | current | This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.10 | Notificationadsl2LinePerfUASThreshAtur | current | This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.11 | Notificationadsl2LinePerfCodingViolationsThreshAtuc | current | This notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.12 | Notificationadsl2LinePerfCodingViolationsThreshAtur | current | This notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.13 | Notificationadsl2LinePerfCorrectedThreshAtuc | current | This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.14 | Notificationadsl2LinePerfCorrectedThreshAtur | current | This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.0.15 | Notificationadsl2LinePerfFailedFullInitThresh | current | This notification indicates that the failed full initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line. | |
| 1.3.6.1.2.1.10.1.0.16 | Notificationadsl2LinePerfFailedShortInitThresh | current | This notification indicates that the failed short initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line. | |
| 1.3.6.1.2.1.10.1.0.17 | Notificationadsl2LineStatusChangeAtuc | current | This notification indicates that a status change is detected for the referred ATU-C. | |
| 1.3.6.1.2.1.10.1.0.18 | Notificationadsl2LineStatusChangeAtur | current | This notification indicates that a status change is detected for the referred ATU-R. | |
| 1.3.6.1.2.1.10.1.1 | Nodeadsl2Line | |||
| 1.3.6.1.2.1.10.1.1.1 | Tableadsl2LineTable | not-accessible | current | The table adsl2LineTable contains configuration, command and status parameters of the ADSL2 line. The index of this table is an interface index where the inter… |
| 1.3.6.1.2.1.10.1.1.1.1 | Rowadsl2LineEntry | not-accessible | current | The table adsl2LineTable contains configuration, commands and status parameters of the ADSL2 line |
| 1.3.6.1.2.1.10.1.1.1.1.1 | Columnadsl2LineCnfgTemplate | read-write | current | The value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (Adsl2ConfTemplatesTable), which applies for this ADSL2 line. |
| 1.3.6.1.2.1.10.1.1.1.1.2 | Columnadsl2LineAlarmCnfgTemplate | read-write | current | The value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL… |
| 1.3.6.1.2.1.10.1.1.1.1.3 | Columnadsl2LineCmndConfPmsf | read-write | current | Power management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0 (0), l0toL2 (2), … |
| 1.3.6.1.2.1.10.1.1.1.1.4 | Columnadsl2LineCmndConfLdsf | read-write | current | Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be respo… |
| 1.3.6.1.2.1.10.1.1.1.1.5 | Columnadsl2LineCmndConfLdsfFailReason | read-only | current | The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none (1) - The default value… |
| 1.3.6.1.2.1.10.1.1.1.1.6 | Columnadsl2LineCmndAutomodeColdStart | read-write | current | Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB.… |
| 1.3.6.1.2.1.10.1.1.1.1.7 | Columnadsl2LineStatusAtuTransSys | read-only | current | The ATU Transmission System (ATS) in use. It is coded in a bit-map representation with one bit set to '1' (the selected coding for the ADSL line). This paramet… |
| 1.3.6.1.2.1.10.1.1.1.1.8 | Columnadsl2LineStatusPwrMngState | read-only | current | The current power management state. One of four possible power management states: L0 - Synchronized and full transmission (i.e., Showtime), L1 - Low Power with… |
| 1.3.6.1.2.1.10.1.1.1.1.9 | Columnadsl2LineStatusInitResult | read-only | current | Indicates the result of the last full initialization performed on the line. It is an enumeration type with the following values: noFailure(0), configError(1), … |
| 1.3.6.1.2.1.10.1.1.1.1.10 | Columnadsl2LineStatusLastStateDs | read-only | current | The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line. States are per the spec… |
| 1.3.6.1.2.1.10.1.1.1.1.11 | Columnadsl2LineStatusLastStateUs | read-only | current | The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line. States are per the specif… |
| 1.3.6.1.2.1.10.1.1.1.1.12 | Columnadsl2LineStatusAtur | read-only | current | Indicates current state (existing failures) of the ATU-R. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), lossOfFraming(… |
| 1.3.6.1.2.1.10.1.1.1.1.13 | Columnadsl2LineStatusAtuc | read-only | current | Indicates current state (existing failures) of the ATU-C. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), lossOfFraming(… |
| 1.3.6.1.2.1.10.1.1.1.1.14 | Columnadsl2LineStatusLnAttenDs | read-only | current | The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during diagnostics mode an… |
| 1.3.6.1.2.1.10.1.1.1.1.15 | Columnadsl2LineStatusLnAttenUs | read-only | current | The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during diagnostics mode an… |
| 1.3.6.1.2.1.10.1.1.1.1.16 | Columnadsl2LineStatusSigAttenDs | read-only | current | The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime. It ranges… |
| 1.3.6.1.2.1.10.1.1.1.1.17 | Columnadsl2LineStatusSigAttenUs | read-only | current | The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime. It ranges… |
| 1.3.6.1.2.1.10.1.1.1.1.18 | Columnadsl2LineStatusSnrMarginDs | read-only | current | Downstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all downstream bearer … |
| 1.3.6.1.2.1.10.1.1.1.1.19 | Columnadsl2LineStatusSnrMarginUs | read-only | current | Upstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all downstream bearer ch… |
| 1.3.6.1.2.1.10.1.1.1.1.20 | Columnadsl2LineStatusAttainableRateDs | read-only | current | Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver, coded in bi… |
| 1.3.6.1.2.1.10.1.1.1.1.21 | Columnadsl2LineStatusAttainableRateUs | read-only | current | Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver, coded in bit/s. |
| 1.3.6.1.2.1.10.1.1.1.1.22 | Columnadsl2LineStatusActPsdDs | read-only | current | Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units o… |
| 1.3.6.1.2.1.10.1.1.1.1.23 | Columnadsl2LineStatusActPsdUs | read-only | current | Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 … |
| 1.3.6.1.2.1.10.1.1.1.1.24 | Columnadsl2LineStatusActAtpDs | read-only | current | Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the ATU-C at the U-C reference point, at the instant of measurement… |
| 1.3.6.1.2.1.10.1.1.1.1.25 | Columnadsl2LineStatusActAtpUs | read-only | current | Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. … |
| 1.3.6.1.2.1.10.1.2 | Nodeadsl2Status | |||
| 1.3.6.1.2.1.10.1.2.1 | Tableadsl2ChannelStatusTable | not-accessible | current | The table adsl2ChannelStatusTable contains status parameters of ADSL2 channel. |
| 1.3.6.1.2.1.10.1.2.1.1 | Rowadsl2ChannelStatusEntry | not-accessible | current | The table adsl2ChannelStatusTable contains status parameters of ADSL2 channel. The index of this table is an interface index where the interface has an ifType … |
| 1.3.6.1.2.1.10.1.2.1.1.1 | Columnadsl2ChStatusUnit | not-accessible | current | The termination unit ATUC(1) or ATUR(2). |
| 1.3.6.1.2.1.10.1.2.1.1.2 | Columnadsl2ChStatusChannelNum | read-only | current | Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the cha… |
| 1.3.6.1.2.1.10.1.2.1.1.3 | Columnadsl2ChStatusActDataRate | read-only | current | The actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The… |
| 1.3.6.1.2.1.10.1.2.1.1.4 | Columnadsl2ChStatusPrevDataRate | read-only | current | The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fas… |
| 1.3.6.1.2.1.10.1.2.1.1.5 | Columnadsl2ChStatusActDelay | read-only | current | The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it … |
| 1.3.6.1.2.1.10.1.2.1.1.6 | Columnadsl2ChStatusAtmStatus | read-only | current | Indicates current state (existing failures) of the ADSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. The various bit positio… |
| 1.3.6.1.2.1.10.1.2.1.1.7 | Columnadsl2ChStatusPtmStatus | read-only | current | Indicates current state (existing failures) of the ADSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. The various bit positio… |
| 1.3.6.1.2.1.10.1.2.2 | Tableadsl2SCStatusTable | not-accessible | current | The table adsl2SCStatusTable contains status parameters of ADSL2 sub-carriers. |
| 1.3.6.1.2.1.10.1.2.2.1 | Rowadsl2SCStatusEntry | not-accessible | current | The table Hfadsl2SCStatusEntry contains status parameters of ADSL2 sub-carriers. The index of this table is an interface index where the interface has an ifTyp… |
| 1.3.6.1.2.1.10.1.2.2.1.1 | Columnadsl2SCStatusDirection | not-accessible | current | The direction of the sub-carrier either upstream or downstream |
| 1.3.6.1.2.1.10.1.2.2.1.2 | Columnadsl2SCStatusMtime | read-only | current | SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specifie… |
| 1.3.6.1.2.1.10.1.2.2.1.3 | Columnadsl2SCStatusSnr | read-only | current | The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 bytes, de… |
| 1.3.6.1.2.1.10.1.2.2.1.4 | Columnadsl2SCStatusBitsAlloc | read-only | current | The bits allocation per sub-carrier. An array of 256 bytes (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized n… |
| 1.3.6.1.2.1.10.1.2.2.1.5 | Columnadsl2SCStatusGainAlloc | read-only | current | The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octet… |
| 1.3.6.1.2.1.10.1.2.2.1.6 | Columnadsl2SCStatusTssi | read-only | current | The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 … |
| 1.3.6.1.2.1.10.1.2.2.1.7 | Columnadsl2SCStatusLinScale | read-only | current | The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loo… |
| 1.3.6.1.2.1.10.1.2.2.1.8 | Columnadsl2SCStatusLinReal | read-only | current | An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 … |
| 1.3.6.1.2.1.10.1.2.2.1.9 | Columnadsl2SCStatusLinImg | read-only | current | An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 … |
| 1.3.6.1.2.1.10.1.2.2.1.10 | Columnadsl2SCStatusLogMt | read-only | current | The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to th… |
| 1.3.6.1.2.1.10.1.2.2.1.11 | Columnadsl2SCStatusLog | read-only | current | An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstr… |
| 1.3.6.1.2.1.10.1.2.2.1.12 | Columnadsl2SCStatusQlnMt | read-only | current | The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value speci… |
| 1.3.6.1.2.1.10.1.2.2.1.13 | Columnadsl2SCStatusQln | read-only | current | An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers … |
| 1.3.6.1.2.1.10.1.2.2.1.14 | Columnadsl2SCStatusLnAtten | read-only | current | When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R… |
| 1.3.6.1.2.1.10.1.2.2.1.15 | Columnadsl2SCStatusSigAtten | read-only | current | When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R… |
| 1.3.6.1.2.1.10.1.2.2.1.16 | Columnadsl2SCStatusSnrMargin | read-only | current | SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the … |
| 1.3.6.1.2.1.10.1.2.2.1.17 | Columnadsl2SCStatusAttainableRate | read-only | current | Maximum Attainable Data Rate. The maximum net data rate currently attainable by the ATU-C transmitter and ATU-R receiver (when referring to downstream directio… |
| 1.3.6.1.2.1.10.1.2.2.1.18 | Columnadsl2SCStatusActAtp | read-only | current | Actual Aggregate Transmit Power from the ATU (ATU-R on downstream direction and ATU-C on upstream direction), at the instant of measurement. It ranges from -31… |
| 1.3.6.1.2.1.10.1.2.2.1.19 | Columnadsl2SCStatusRowStatus | read-write | current | Row Status. The SNMP agent should create a row in this table for storing the results of a DELT performed on the associated line, if such a row does not already… |
| 1.3.6.1.2.1.10.1.3 | Nodeadsl2Inventory | |||
| 1.3.6.1.2.1.10.1.3.1 | Tableadsl2LineInventoryTable | not-accessible | current | The table adsl2LineInventoryTable contains inventory of ADSL2 unit. |
| 1.3.6.1.2.1.10.1.3.1.1 | Rowadsl2LineInventoryEntry | not-accessible | current | The table adsl2LineInventoryTable contains inventory of ADSL2 unit. The index of this table is an interface index where the interface has an ifType of adsl2(23… |
| 1.3.6.1.2.1.10.1.3.1.1.1 | Columnadsl2LInvUnit | not-accessible | current | The termination unit ATUC{1} or ATUR{2}. |
| 1.3.6.1.2.1.10.1.3.1.1.2 | Columnadsl2LInvG994VendorId | read-only | current | The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocat… |
| 1.3.6.1.2.1.10.1.3.1.1.3 | Columnadsl2LInvSystemVendorId | read-only | current | The ATU System Vendor ID (identifies the ATU system integrator) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Ope… |
| 1.3.6.1.2.1.10.1.3.1.1.4 | Columnadsl2LInvVersionNumber | read-only | current | The ATU version number (vendor specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Cha… |
| 1.3.6.1.2.1.10.1.3.1.1.5 | Columnadsl2LInvSerialNumber | read-only | current | The ATU serial number (vendor specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Chan… |
| 1.3.6.1.2.1.10.1.3.1.1.6 | Columnadsl2LInvSelfTestResult | read-only | current | The ATU self-test result, coded as a 32-bit integer. The most significant octet of this object is '0' if the self-test passed, and '1' if the self-test failed.… |
| 1.3.6.1.2.1.10.1.3.1.1.7 | Columnadsl2LInvTransmissionCapabilities | read-only | current | The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' me… |
| 1.3.6.1.2.1.10.1.4 | Nodeadsl2PM | |||
| 1.3.6.1.2.1.10.1.4.1 | Nodeadsl2PMLine | |||
| 1.3.6.1.2.1.10.1.4.1.1 | Tableadsl2PMLineCurrTable | not-accessible | current | The table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. |
| 1.3.6.1.2.1.10.1.4.1.1.1 | Rowadsl2PMLineCurrEntry | not-accessible | current | The table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The index of this table is an interface index where the interface… |
| 1.3.6.1.2.1.10.1.4.1.1.1.1 | Columnadsl2PMLCurrUnit | not-accessible | current | The termination unit ATUC{1} or ATUR{2}. |
| 1.3.6.1.2.1.10.1.4.1.1.1.2 | Columnadsl2PMLCurrValidIntervals | read-only | current | Valid intervals. |
| 1.3.6.1.2.1.10.1.4.1.1.1.3 | Columnadsl2PMLCurrInvalidIntervals | read-only | current | Invalid intervals. |
| 1.3.6.1.2.1.10.1.4.1.1.1.4 | Columnadsl2PMLCurr15MTimeElapsed | read-only | current | Total elapsed seconds in this interval |
| 1.3.6.1.2.1.10.1.4.1.1.1.5 | Columnadsl2PMLCurr15MFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.1.4.1.1.1.6 | Columnadsl2PMLCurr15MEs | read-only | current | Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 ATU-R: FEBE >= 1 for… |
| 1.3.6.1.2.1.10.1.4.1.1.1.7 | Columnadsl2PMLCurr15MSes | read-only | current | Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE sum… |
| 1.3.6.1.2.1.10.1.4.1.1.1.8 | Columnadsl2PMLCurr15MLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R). |
| 1.3.6.1.2.1.10.1.4.1.1.1.9 | Columnadsl2PMLCurr15MUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the on… |
| 1.3.6.1.2.1.10.1.4.1.1.1.10 | Columnadsl2PMLCurr1DayValidIntervals | read-only | current | Valid intervals. |
| 1.3.6.1.2.1.10.1.4.1.1.1.11 | Columnadsl2PMLCurr1DayInvalidIntervals | read-only | current | Invalid intervals. |
| 1.3.6.1.2.1.10.1.4.1.1.1.12 | Columnadsl2PMLCurr1DayTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.1.4.1.1.1.13 | Columnadsl2PMLCurr1DayFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.1.4.1.1.1.14 | Columnadsl2PMLCurr1DayEs | read-only | current | Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 fo… |
| 1.3.6.1.2.1.10.1.4.1.1.1.15 | Columnadsl2PMLCurr1DaySes | read-only | current | Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE sum… |
| 1.3.6.1.2.1.10.1.4.1.1.1.16 | Columnadsl2PMLCurr1DayLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R). |
| 1.3.6.1.2.1.10.1.4.1.1.1.17 | Columnadsl2PMLCurr1DayUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the o… |
| 1.3.6.1.2.1.10.1.4.1.2 | Tableadsl2PMLineCurrInitTable | not-accessible | current | The table adsl2PMLineCurrInitTable contains current initialization counters of ADSL2 line. |
| 1.3.6.1.2.1.10.1.4.1.2.1 | Rowadsl2PMLineCurrInitEntry | not-accessible | current | The table adsl2PMLineCurrInitTable contains current initialization counters of ADSL2 line. The index of this table is an interface index where the interface ha… |
| 1.3.6.1.2.1.10.1.4.1.2.1.1 | Columnadsl2PMLCurrInit15MTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.2 | Columnadsl2PMLCurrInit15MFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.3 | Columnadsl2PMLCurrInit15MFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.4 | Columnadsl2PMLCurrInit15MShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.5 | Columnadsl2PMLCurrInit15MFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.6 | Columnadsl2PMLCurrInit1DayTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.7 | Columnadsl2PMLCurrInit1DayFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.8 | Columnadsl2PMLCurrInit1DayFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.9 | Columnadsl2PMLCurrInit1DayShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.2.1.10 | Columnadsl2PMLCurrInit1DayFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.3 | Tableadsl2PMLineHist15MinTable | not-accessible | current | The table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of ADSL2 line. |
| 1.3.6.1.2.1.10.1.4.1.3.1 | Rowadsl2PMLineHist15MinEntry | not-accessible | current | The table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of ADSL2 line. The index of this table is an interface index where the interfa… |
| 1.3.6.1.2.1.10.1.4.1.3.1.1 | Columnadsl2PMLHist15MUnit | not-accessible | current | The termination unit ATUC{1} or ATUR{2}. |
| 1.3.6.1.2.1.10.1.4.1.3.1.2 | Columnadsl2PMLHist15MInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.1.4.1.3.1.3 | Columnadsl2PMLHist15MMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.1.4.1.3.1.4 | Columnadsl2PMLHist15MFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.1.4.1.3.1.5 | Columnadsl2PMLHist15MEs | read-only | current | Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 fo… |
| 1.3.6.1.2.1.10.1.4.1.3.1.6 | Columnadsl2PMLHist15MSes | read-only | current | Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE sum… |
| 1.3.6.1.2.1.10.1.4.1.3.1.7 | Columnadsl2PMLHist15MLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R). |
| 1.3.6.1.2.1.10.1.4.1.3.1.8 | Columnadsl2PMLHist15MUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the o… |
| 1.3.6.1.2.1.10.1.4.1.3.1.9 | Columnadsl2PMLHist15MValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.1.4.1.4 | Tableadsl2PMLineHist1DayTable | not-accessible | current | The table adsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of ADSL2 line. |
| 1.3.6.1.2.1.10.1.4.1.4.1 | Rowadsl2PMLineHist1DayEntry | not-accessible | current | The table adsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of ADSL2 line. The indexes of this table is an interface index where the int… |
| 1.3.6.1.2.1.10.1.4.1.4.1.1 | Columnadsl2PMLHist1DUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.1.4.1.4.1.2 | Columnadsl2PMLHist1DInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.1.4.1.4.1.3 | Columnadsl2PMLHist1DMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.1.4.1.4.1.4 | Columnadsl2PMLHist1DFecs | read-only | current | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibite… |
| 1.3.6.1.2.1.10.1.4.1.4.1.5 | Columnadsl2PMLHist1DEs | read-only | current | Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 fo… |
| 1.3.6.1.2.1.10.1.4.1.4.1.6 | Columnadsl2PMLHist1DSes | read-only | current | Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >> 1 OR LPR >= 1 ATU-R: (FEBE sum… |
| 1.3.6.1.2.1.10.1.4.1.4.1.7 | Columnadsl2PMLHist1DLoss | read-only | current | Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R). |
| 1.3.6.1.2.1.10.1.4.1.4.1.8 | Columnadsl2PMLHist1DUas | read-only | current | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the o… |
| 1.3.6.1.2.1.10.1.4.1.4.1.9 | Columnadsl2PMLHist1DValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.1.4.1.5 | Tableadsl2PMLineInitHist15MinTable | not-accessible | current | The table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of ADSL2 line. |
| 1.3.6.1.2.1.10.1.4.1.5.1 | Rowadsl2PMLineInitHist15MinEntry | not-accessible | current | The table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of ADSL2 line. The index of this table is an interface… |
| 1.3.6.1.2.1.10.1.4.1.5.1.1 | Columnadsl2PMLHistInit15MInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.1.4.1.5.1.2 | Columnadsl2PMLHistInit15MMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.1.4.1.5.1.3 | Columnadsl2PMLHistInit15MFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.5.1.4 | Columnadsl2PMLHistInit15MFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.5.1.5 | Columnadsl2PMLHistInit15MShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.5.1.6 | Columnadsl2PMLHistInit15MFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.5.1.7 | Columnadsl2PMLHistInit15MValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.1.4.1.6 | Tableadsl2PMLineInitHist1DayTable | not-accessible | current | The table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of ADSL2 line. |
| 1.3.6.1.2.1.10.1.4.1.6.1 | Rowadsl2PMLineInitHist1DayEntry | not-accessible | current | The table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of ADSL2 line. The indexes of this table is an interface … |
| 1.3.6.1.2.1.10.1.4.1.6.1.1 | Columnadsl2PMLHistinit1DInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.1.4.1.6.1.2 | Columnadsl2PMLHistinit1DMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.1.4.1.6.1.3 | Columnadsl2PMLHistinit1DFullInits | read-only | current | Count of full initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.6.1.4 | Columnadsl2PMLHistinit1DFailedFullInits | read-only | current | Count of failed full initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.6.1.5 | Columnadsl2PMLHistinit1DShortInits | read-only | current | Count of short initializations attempted on the line (successful and failed) during this interval. |
| 1.3.6.1.2.1.10.1.4.1.6.1.6 | Columnadsl2PMLHistinit1DFailedShortInits | read-only | current | Count of failed short initializations on the line during this interval. |
| 1.3.6.1.2.1.10.1.4.1.6.1.7 | Columnadsl2PMLHistinit1DValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.1.4.2 | Nodeadsl2PMChannel | |||
| 1.3.6.1.2.1.10.1.4.2.1 | Tableadsl2PMChCurrTable | not-accessible | current | The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. |
| 1.3.6.1.2.1.10.1.4.2.1.1 | Rowadsl2PMChCurrEntry | not-accessible | current | The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The indexes of this table is an interface index where the interf… |
| 1.3.6.1.2.1.10.1.4.2.1.1.1 | Columnadsl2PMChCurrUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.1.4.2.1.1.2 | Columnadsl2PMChCurrValidIntervals | read-only | current | Valid intervals. |
| 1.3.6.1.2.1.10.1.4.2.1.1.3 | Columnadsl2PMChCurrInvalidIntervals | read-only | current | Invalid intervals. |
| 1.3.6.1.2.1.10.1.4.2.1.1.4 | Columnadsl2PMChCurr15MTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.1.4.2.1.1.5 | Columnadsl2PMChCurr15MCodingViolations | read-only | current | Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.1.4.2.1.1.6 | Columnadsl2PMChCurr15MCorrectedBlocks | read-only | current | Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.1.4.2.1.1.7 | Columnadsl2PMChCurr1DayValidIntervals | read-only | current | Valid intervals. |
| 1.3.6.1.2.1.10.1.4.2.1.1.8 | Columnadsl2PMChCurr1DayInvalidIntervals | read-only | current | Invalid intervals. |
| 1.3.6.1.2.1.10.1.4.2.1.1.9 | Columnadsl2PMChCurr1DayTimeElapsed | read-only | current | Total elapsed seconds in this interval. |
| 1.3.6.1.2.1.10.1.4.2.1.1.10 | Columnadsl2PMChCurr1DayCodingViolations | read-only | current | Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.1.4.2.1.1.11 | Columnadsl2PMChCurr1DayCorrectedBlocks | read-only | current | Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.1.4.2.2 | Tableadsl2PMChHist15MinTable | not-accessible | current | The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. |
| 1.3.6.1.2.1.10.1.4.2.2.1 | Rowadsl2PMChHist15MinEntry | not-accessible | current | The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The indexes of this table is an interface index where the interf… |
| 1.3.6.1.2.1.10.1.4.2.2.1.1 | Columnadsl2PMChHist15MUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.1.4.2.2.1.2 | Columnadsl2PMChHist15MInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.1.4.2.2.1.3 | Columnadsl2PMChHist15MMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.1.4.2.2.1.4 | Columnadsl2PMChHist15MCodingViolations | read-only | current | Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.1.4.2.2.1.5 | Columnadsl2PMChHist15MCorrectedBlocks | read-only | current | Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.1.4.2.2.1.6 | Columnadsl2PMChHist15MValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.1.4.2.3 | Tableadsl2PMChHist1DTable | not-accessible | current | The table adsl2PMChHist1DayTable contains PM channel history for 1 day intervals of ADSL2. |
| 1.3.6.1.2.1.10.1.4.2.3.1 | Rowadsl2PMChHist1DEntry | not-accessible | current | The table adsl2PMChHist1DayTable contains PM channel history for 1 day intervals of ADSL2. The indexes of this table is an interface index where the interface … |
| 1.3.6.1.2.1.10.1.4.2.3.1.1 | Columnadsl2PMChHist1DUnit | not-accessible | current | The termination unit. |
| 1.3.6.1.2.1.10.1.4.2.3.1.2 | Columnadsl2PMChHist1DInterval | not-accessible | current | The interval number. |
| 1.3.6.1.2.1.10.1.4.2.3.1.3 | Columnadsl2PMChHist1DMonitoredTime | read-only | current | Total seconds monitored in this interval. |
| 1.3.6.1.2.1.10.1.4.2.3.1.4 | Columnadsl2PMChHist1DCodingViolations | read-only | current | Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied ov… |
| 1.3.6.1.2.1.10.1.4.2.3.1.5 | Columnadsl2PMChHist1DCorrectedBlocks | read-only | current | Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If … |
| 1.3.6.1.2.1.10.1.4.2.3.1.6 | Columnadsl2PMChHist1DValidInterval | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.10.1.5 | Nodeadsl2Profile | |||
| 1.3.6.1.2.1.10.1.5.1 | Nodeadsl2ProfileLine | |||
| 1.3.6.1.2.1.10.1.5.1.1 | Tableadsl2LineConfTemplateTable | not-accessible | current | The table adsl2LineConfTemplateTable contains ADSL2 line configuration template. |
| 1.3.6.1.2.1.10.1.5.1.1.1 | Rowadsl2LineConfTemplateEntry | not-accessible | current | The table adsl2LineConfTemplateTable contains ADSL2 line configuration template. A default template with an index of 'DEFVAL' will always exist and its paramet… |
| 1.3.6.1.2.1.10.1.5.1.1.1.1 | Columnadsl2LConfTempTemplateName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.1.5.1.1.1.2 | Columnadsl2LConfTempLineProfile | read-create | current | The value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (Adsl2LineConfProfileTable), which applies for this ADSL2 line. |
| 1.3.6.1.2.1.10.1.5.1.1.1.3 | Columnadsl2LConfTempChan1ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel … |
| 1.3.6.1.2.1.10.1.5.1.1.1.4 | Columnadsl2LConfTempChan1RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio re… |
| 1.3.6.1.2.1.10.1.5.1.1.1.5 | Columnadsl2LConfTempChan1RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refe… |
| 1.3.6.1.2.1.10.1.5.1.1.1.6 | Columnadsl2LConfTempChan2ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel … |
| 1.3.6.1.2.1.10.1.5.1.1.1.7 | Columnadsl2LConfTempChan2RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio re… |
| 1.3.6.1.2.1.10.1.5.1.1.1.8 | Columnadsl2LConfTempChan2RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refe… |
| 1.3.6.1.2.1.10.1.5.1.1.1.9 | Columnadsl2LConfTempChan3ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel … |
| 1.3.6.1.2.1.10.1.5.1.1.1.10 | Columnadsl2LConfTempChan3RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio re… |
| 1.3.6.1.2.1.10.1.5.1.1.1.11 | Columnadsl2LConfTempChan3RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refe… |
| 1.3.6.1.2.1.10.1.5.1.1.1.12 | Columnadsl2LConfTempChan4ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (Adsl2ChanConfProfileTableDs) that applies to ADSL2 bearer channel… |
| 1.3.6.1.2.1.10.1.5.1.1.1.13 | Columnadsl2LConfTempChan4RaRatioDs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio re… |
| 1.3.6.1.2.1.10.1.5.1.1.1.14 | Columnadsl2LConfTempChan4RaRatioUs | read-create | current | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refe… |
| 1.3.6.1.2.1.10.1.5.1.1.1.15 | Columnadsl2LConfTempRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.5.1.2 | Tableadsl2LineConfProfTable | not-accessible | current | The table adsl2LineConfProfTable contains ADSL2 line profile configuration. |
| 1.3.6.1.2.1.10.1.5.1.2.1 | Rowadsl2LineConfProfEntry | not-accessible | current | The table adsl2LineConfProfTable contains ADSL2 line profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters wi… |
| 1.3.6.1.2.1.10.1.5.1.2.1.1 | Columnadsl2LConfProfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.1.5.1.2.1.2 | Columnadsl2LConfProfScMaskDs | read-create | current | Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the… |
| 1.3.6.1.2.1.10.1.5.1.2.1.3 | Columnadsl2LConfProfScMaskUs | read-create | current | Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the r… |
| 1.3.6.1.2.1.10.1.5.1.2.1.4 | Columnadsl2LConfProfRfiBandsDs | read-create | current | The subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It… |
| 1.3.6.1.2.1.10.1.5.1.2.1.5 | Columnadsl2LConfProfRaModeDs | read-create | current | The mode of operation of a rate-adaptive ATU-C in the transmit direction. The parameter can take three values: manual (1), raInit (2), dynamicRa (3). |
| 1.3.6.1.2.1.10.1.5.1.2.1.6 | Columnadsl2LConfProfRaModeUs | read-create | current | The mode of operation of a rate-adaptive ATU-R in the transmit direction. The parameter can take three values: manual (1), raInit (2), dynamicRa (3). |
| 1.3.6.1.2.1.10.1.5.1.2.1.7 | Columnadsl2LConfProfRaUsNrmDs | read-create | current | The Downstream Up-Shift Noise Margin value, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is above this value and s… |
| 1.3.6.1.2.1.10.1.5.1.2.1.8 | Columnadsl2LConfProfRaUsNrmUs | read-create | current | The Upstream Up-Shift Noise Margin value, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is above this value and stays… |
| 1.3.6.1.2.1.10.1.5.1.2.1.9 | Columnadsl2LConfProfRaUsTimeDs | read-create | current | The Downstream Up-Shift Time Interval, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. The interval of time that the downstream noise margin should … |
| 1.3.6.1.2.1.10.1.5.1.2.1.10 | Columnadsl2LConfProfRaUsTimeUs | read-create | current | The Upstream Up-Shift Time Interval, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay abov… |
| 1.3.6.1.2.1.10.1.5.1.2.1.11 | Columnadsl2LConfProfRaDsNrmsDs | read-create | current | The Downstream Down-Shift Noise Margin value, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is below this value and… |
| 1.3.6.1.2.1.10.1.5.1.2.1.12 | Columnadsl2LConfProfRaDsNrmsUs | read-create | current | The Upstream Downshift Noise Margin value, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is below this value and stay… |
| 1.3.6.1.2.1.10.1.5.1.2.1.13 | Columnadsl2LConfProfRaDsTimeDs | read-create | current | The Downstream Downshift Time Interval, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. The interval of time the downstream noise margin should stay… |
| 1.3.6.1.2.1.10.1.5.1.2.1.14 | Columnadsl2LConfProfRaDsTimeUs | read-create | current | The Upstream Down-Shift Time Interval, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay be… |
| 1.3.6.1.2.1.10.1.5.1.2.1.15 | Columnadsl2LConfProfTargetSnrmDs | read-create | current | The minimum Noise Margin the ATU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete… |
| 1.3.6.1.2.1.10.1.5.1.2.1.16 | Columnadsl2LConfProfTargetSnrmUs | read-create | current | The minimum Noise Margin the ATU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete i… |
| 1.3.6.1.2.1.10.1.5.1.2.1.17 | Columnadsl2LConfProfMaxSnrmDs | read-create | current | The maximum Noise Margin the ATU-R receiver shall try to sustain. If the Noise Margin is above this level, the ATU-R shall request that the ATU-C reduce the AT… |
| 1.3.6.1.2.1.10.1.5.1.2.1.18 | Columnadsl2LConfProfMaxSnrmUs | read-create | current | The maximum Noise Margin the ATU-C receiver shall try to sustain. If the Noise Margin is above this level, the ATU-C shall request that the ATU-R reduce the AT… |
| 1.3.6.1.2.1.10.1.5.1.2.1.19 | Columnadsl2LConfProfMinSnrmDs | read-create | current | The minimum Noise Margin the ATU-R receiver shall tolerate. If the noise margin falls below this level, the ATU-R shall request that the ATU-C increase the ATU… |
| 1.3.6.1.2.1.10.1.5.1.2.1.20 | Columnadsl2LConfProfMinSnrmUs | read-create | current | The minimum Noise Margin the ATU-C receiver shall tolerate. If the noise margin falls below this level, the ATU-C shall request that the ATU-R increase the ATU… |
| 1.3.6.1.2.1.10.1.5.1.2.1.21 | Columnadsl2LConfProfMsgMinUs | read-create | current | Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in upstream direction. Expressed in … |
| 1.3.6.1.2.1.10.1.5.1.2.1.22 | Columnadsl2LConfProfMsgMinDs | read-create | current | Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in downstream direction. Expressed… |
| 1.3.6.1.2.1.10.1.5.1.2.1.23 | Columnadsl2LConfProfAtuTransSysEna | read-create | current | ATU Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more b… |
| 1.3.6.1.2.1.10.1.5.1.2.1.24 | Columnadsl2LConfProfPmMode | read-create | current | Power management state Enabling. Defines the power states the ATU-C or ATU-R may autonomously transition to on this line. The various bit positions are: allowT… |
| 1.3.6.1.2.1.10.1.5.1.2.1.25 | Columnadsl2LConfProfL0Time | read-create | current | This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds. |
| 1.3.6.1.2.1.10.1.5.1.2.1.26 | Columnadsl2LConfProfL2Time | read-create | current | This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 St… |
| 1.3.6.1.2.1.10.1.5.1.2.1.27 | Columnadsl2LConfProfL2Atpr | read-create | current | The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It… |
| 1.3.6.1.2.1.10.1.5.1.2.1.28 | Columnadsl2LConfProfL2Atprt | read-create | current | The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at tr… |
| 1.3.6.1.2.1.10.1.5.1.2.1.29 | Columnadsl2LConfProfRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.5.1.3 | Tableadsl2LineConfProfModeSpecTable | not-accessible | current | The table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters. A row in this table that has an index o… |
| 1.3.6.1.2.1.10.1.5.1.3.1 | Rowadsl2LineConfProfModeSpecEntry | not-accessible | current | The table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters. |
| 1.3.6.1.2.1.10.1.5.1.3.1.1 | Columnadsl2LconfProfAdslMode | not-accessible | current | The ADSL Mode is a way of categorizing the various ADSL transmission modes into groups, each group (ADSL Mode) shares the same PSD configuration. There should … |
| 1.3.6.1.2.1.10.1.5.1.3.1.2 | Columnadsl2LConfProfMaxNomPsdDs | read-create | current | The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical val… |
| 1.3.6.1.2.1.10.1.5.1.3.1.3 | Columnadsl2LConfProfMaxNomPsdUs | read-create | current | The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical value… |
| 1.3.6.1.2.1.10.1.5.1.3.1.4 | Columnadsl2LConfProfMaxNomAtpDs | read-create | current | The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical… |
| 1.3.6.1.2.1.10.1.5.1.3.1.5 | Columnadsl2LConfProfMaxNomAtpUs | read-create | current | The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical v… |
| 1.3.6.1.2.1.10.1.5.1.3.1.6 | Columnadsl2LConfProfMaxAggRxPwrUs | read-create | current | The maximum upstream aggregate receive power over the relevant set of sub-carriers. The ATU-C should verify that the upstream power cutback is such that this m… |
| 1.3.6.1.2.1.10.1.5.1.3.1.7 | Columnadsl2LConfProfPsdMaskDs | read-create | current | The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in add… |
| 1.3.6.1.2.1.10.1.5.1.3.1.8 | Columnadsl2LConfProfPsdMaskUs | read-create | current | The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addit… |
| 1.3.6.1.2.1.10.1.5.1.3.1.9 | Columnadsl2LConfProfPsdMaskSelectUs | read-create | current | The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled… |
| 1.3.6.1.2.1.10.1.5.1.3.1.10 | Columnadsl2LConfProfModeSpecRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.5.2 | Nodeadsl2ProfileChannel | |||
| 1.3.6.1.2.1.10.1.5.2.1 | Tableadsl2ChConfProfileTable | not-accessible | current | The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. |
| 1.3.6.1.2.1.10.1.5.2.1.1 | Rowadsl2ChConfProfileEntry | not-accessible | current | The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameter… |
| 1.3.6.1.2.1.10.1.5.2.1.1.1 | Columnadsl2ChConfProfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.1.5.2.1.1.2 | Columnadsl2ChConfProfMinDataRateDs | read-create | current | Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.1.5.2.1.1.3 | Columnadsl2ChConfProfMinDataRateUs | read-create | current | Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.1.5.2.1.1.4 | Columnadsl2ChConfProfMinResDataRateDs | read-create | current | Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if t… |
| 1.3.6.1.2.1.10.1.5.2.1.1.5 | Columnadsl2ChConfProfMinResDataRateUs | read-create | current | Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the… |
| 1.3.6.1.2.1.10.1.5.2.1.1.6 | Columnadsl2ChConfProfMaxDataRateDs | read-create | current | Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.1.5.2.1.1.7 | Columnadsl2ChConfProfMaxDataRateUs | read-create | current | Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bit/s. |
| 1.3.6.1.2.1.10.1.5.2.1.1.8 | Columnadsl2ChConfProfMinDataRateLowPwrDs | read-create | current | Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s., during the low power state (L1… |
| 1.3.6.1.2.1.10.1.5.2.1.1.9 | Columnadsl2ChConfProfMinDataRateLowPwrUs | read-create | current | Minimum Data Rate in Low Power state on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s., during the low power state (L1 i… |
| 1.3.6.1.2.1.10.1.5.2.1.1.10 | Columnadsl2ChConfProfMaxDelayDs | read-create | current | Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The ATUs shall choos… |
| 1.3.6.1.2.1.10.1.5.2.1.1.11 | Columnadsl2ChConfProfMaxDelayUs | read-create | current | Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The ATUs shall choose th… |
| 1.3.6.1.2.1.10.1.5.2.1.1.12 | Columnadsl2ChConfProfMinProtectionDs | read-create | current | Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can … |
| 1.3.6.1.2.1.10.1.5.2.1.1.13 | Columnadsl2ChConfProfMinProtectionUs | read-create | current | Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can ta… |
| 1.3.6.1.2.1.10.1.5.2.1.1.14 | Columnadsl2ChConfProfMaxBerDs | read-create | current | Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-… |
| 1.3.6.1.2.1.10.1.5.2.1.1.15 | Columnadsl2ChConfProfMaxBerUs | read-create | current | Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 … |
| 1.3.6.1.2.1.10.1.5.2.1.1.16 | Columnadsl2ChConfProfUsDataRateDs | read-create | current | Data Rate Threshold Up shift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than … |
| 1.3.6.1.2.1.10.1.5.2.1.1.17 | Columnadsl2ChConfProfDsDataRateDs | read-create | current | Data Rate Threshold Downshift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data ra… |
| 1.3.6.1.2.1.10.1.5.2.1.1.18 | Columnadsl2ChConfProfUsDataRateUs | read-create | current | Data Rate Threshold Up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the … |
| 1.3.6.1.2.1.10.1.5.2.1.1.19 | Columnadsl2ChConfProfDsDataRateUs | read-create | current | Data Rate Threshold Downshift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate a… |
| 1.3.6.1.2.1.10.1.5.2.1.1.20 | Columnadsl2ChConfProfImaEnabled | read-create | current | IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is of ATM Data Path. When in 'enable' state, t… |
| 1.3.6.1.2.1.10.1.5.2.1.1.21 | Columnadsl2ChConfProfRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.5.3 | Nodeadsl2ProfileAlarmConf | |||
| 1.3.6.1.2.1.10.1.5.3.1 | Tableadsl2LineAlarmConfTemplateTable | not-accessible | current | The table adsl2LineConfTemplateTable contains ADSL2 line configuration template. |
| 1.3.6.1.2.1.10.1.5.3.1.1 | Rowadsl2LineAlarmConfTemplateEntry | not-accessible | current | The table adsl2LineAlarmConfTemplateTable contains ADSL2 line PM thresholds template. A default template with an index of 'DEFVAL' will always exist and its pa… |
| 1.3.6.1.2.1.10.1.5.3.1.1.1 | Columnadsl2LAlarmConfTempTemplateName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.1.5.3.1.1.2 | Columnadsl2LAlarmConfTempLineProfile | read-create | current | The value of this object identifies the row in the ADSL2 Line Thresholds Configuration Profile Table (adsl2LineAlarmConfProfileTable) that applies to this ADSL… |
| 1.3.6.1.2.1.10.1.5.3.1.1.3 | Columnadsl2LAlarmConfTempChan1ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 b… |
| 1.3.6.1.2.1.10.1.5.3.1.1.4 | Columnadsl2LAlarmConfTempChan2ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 b… |
| 1.3.6.1.2.1.10.1.5.3.1.1.5 | Columnadsl2LAlarmConfTempChan3ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 b… |
| 1.3.6.1.2.1.10.1.5.3.1.1.6 | Columnadsl2LAlarmConfTempChan4ConfProfile | read-create | current | The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 b… |
| 1.3.6.1.2.1.10.1.5.3.1.1.7 | Columnadsl2LAlarmConfTempRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.5.3.2 | Tableadsl2LineAlarmConfProfileTable | not-accessible | current | The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. |
| 1.3.6.1.2.1.10.1.5.3.2.1 | Rowadsl2LineAlarmConfProfileEntry | not-accessible | current | The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist and its para… |
| 1.3.6.1.2.1.10.1.5.3.2.1.1 | Columnadsl2LineAlarmConfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.1.5.3.2.1.2 | Columnadsl2LineAlarmConfProfileAtucThresh15MinFecs | read-create | current | A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.3 | Columnadsl2LineAlarmConfProfileAtucThresh15MinEs | read-create | current | A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.4 | Columnadsl2LineAlarmConfProfileAtucThresh15MinSes | read-create | current | A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.5 | Columnadsl2LineAlarmConfProfileAtucThresh15MinLoss | read-create | current | A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.6 | Columnadsl2LineAlarmConfProfileAtucThresh15MinUas | read-create | current | A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.7 | Columnadsl2LineAlarmConfProfileAturThresh15MinFecs | read-create | current | A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.8 | Columnadsl2LineAlarmConfProfileAturThresh15MinEs | read-create | current | A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.9 | Columnadsl2LineAlarmConfProfileAturThresh15MinSes | read-create | current | A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.10 | Columnadsl2LineAlarmConfProfileAturThresh15MinLoss | read-create | current | A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.11 | Columnadsl2LineAlarmConfProfileAturThresh15MinUas | read-create | current | A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.12 | Columnadsl2LineAlarmConfProfileThresh15MinFailedFullInt | read-create | current | A threshold for the adsl2PMLCurrInit15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.13 | Columnadsl2LineAlarmConfProfileThresh15MinFailedShrtInt | read-create | current | A threshold for the adsl2PMLCurrInit15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter. |
| 1.3.6.1.2.1.10.1.5.3.2.1.14 | Columnadsl2LineAlarmConfProfileRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.5.3.3 | Tableadsl2ChAlarmConfProfileTable | not-accessible | current | The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. |
| 1.3.6.1.2.1.10.1.5.3.3.1 | Rowadsl2ChAlarmConfProfileEntry | not-accessible | current | The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist and its par… |
| 1.3.6.1.2.1.10.1.5.3.3.1.1 | Columnadsl2ChAlarmConfProfileName | not-accessible | current | This object identifies a row in this table. |
| 1.3.6.1.2.1.10.1.5.3.3.1.2 | Columnadsl2ChAlarmConfProfileAtucThresh15MinCodingViolations | read-create | current | A threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the asso… |
| 1.3.6.1.2.1.10.1.5.3.3.1.3 | Columnadsl2ChAlarmConfProfileAtucThresh15MinCorrected | read-create | current | A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the assoc… |
| 1.3.6.1.2.1.10.1.5.3.3.1.4 | Columnadsl2ChAlarmConfProfileAturThresh15MinCodingViolations | read-create | current | A threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the asso… |
| 1.3.6.1.2.1.10.1.5.3.3.1.5 | Columnadsl2ChAlarmConfProfileAturThresh15MinCorrected | read-create | current | A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the assoc… |
| 1.3.6.1.2.1.10.1.5.3.3.1.6 | Columnadsl2ChAlarmConfProfileRowStatus | read-create | current | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When '… |
| 1.3.6.1.2.1.10.1.6 | Nodeadsl2Scalar | |||
| 1.3.6.1.2.1.10.1.6.1 | Nodeadsl2ScalarSC | |||
| 1.3.6.1.2.1.10.1.6.1.1 | Scalaradsl2ScalarSCMaxInterfaces | read-only | current | This value determines the upper size of adsl2SCStatusTable. The maximum number of entries in adsl2SCStatusTable is equal to two times the value of this attribu… |
| 1.3.6.1.2.1.10.1.6.1.2 | Scalaradsl2ScalarSCAvailInterfaces | read-only | current | This value determines the amount of space that is currently available in adsl2SCStatusTable. The number of entries available in adsl2SCStatusTable is equal to … |
| 1.3.6.1.2.1.10.1.8 | Nodeadsl2Conformance | |||
| 1.3.6.1.2.1.10.1.8.1 | Nodeadsl2Groups | |||
| 1.3.6.1.2.1.10.1.8.1.1 | Groupadsl2LineGroup | current | The group of configuration, status, and commands objects on the line level. | |
| 1.3.6.1.2.1.10.1.8.1.2 | Groupadsl2ChannelStatusGroup | current | The group of status objects on the channel level. | |
| 1.3.6.1.2.1.10.1.8.1.3 | Groupadsl2ChannelStatusAtmGroup | current | The group of status objects on the data path level when it is ATM. | |
| 1.3.6.1.2.1.10.1.8.1.4 | Groupadsl2ChannelStatusPtmGroup | current | The group of status objects on the data path level when it is PTM. | |
| 1.3.6.1.2.1.10.1.8.1.5 | Groupadsl2SCStatusGroup | current | The group of status objects on the sub-carrier level. They are updated as a result of a DELT process. | |
| 1.3.6.1.2.1.10.1.8.1.6 | Groupadsl2LineInventoryGroup | current | The group of inventory objects per xTU. | |
| 1.3.6.1.2.1.10.1.8.1.7 | Groupadsl2LineConfTemplateGroup | current | The group of objects in a line configuration template. | |
| 1.3.6.1.2.1.10.1.8.1.8 | Groupadsl2LineConfProfGroup | current | The group of objects in a line configuration profile. | |
| 1.3.6.1.2.1.10.1.8.1.9 | Groupadsl2LineConfProfRaGroup | current | The group of objects required for controlling the rate adaptive behavior of the line. | |
| 1.3.6.1.2.1.10.1.8.1.10 | Groupadsl2LineConfProfMsgMinGroup | current | The group of objects required for controlling the rate reserved for Overhead traffic. | |
| 1.3.6.1.2.1.10.1.8.1.11 | Groupadsl2LineConfProfModeSpecGroup | current | The group of objects in a line configuration profile that have an instance for each operation mode allowed. | |
| 1.3.6.1.2.1.10.1.8.1.12 | Groupadsl2ChConfProfileGroup | current | The group of objects in a channel configuration profile. | |
| 1.3.6.1.2.1.10.1.8.1.13 | Groupadsl2ChConfProfileAtmGroup | current | The group of configuration objects required when the data path is ATM. | |
| 1.3.6.1.2.1.10.1.8.1.14 | Groupadsl2ChConfProfileMinResGroup | current | The group of configuration objects required for the reserved data rate. | |
| 1.3.6.1.2.1.10.1.8.1.15 | Groupadsl2LineAlarmConfTemplateGroup | current | The group of objects in a line alarm template. | |
| 1.3.6.1.2.1.10.1.8.1.16 | Groupadsl2LineAlarmConfProfileGroup | current | The group of objects in a line alarm profile. | |
| 1.3.6.1.2.1.10.1.8.1.17 | Groupadsl2ChAlarmConfProfileGroup | current | The group of objects in a channel alarm profile. | |
| 1.3.6.1.2.1.10.1.8.1.18 | Groupadsl2PMLineCurrGroup | current | The group of objects that report the line level counters for current PM intervals. | |
| 1.3.6.1.2.1.10.1.8.1.19 | Groupadsl2PMLineCurrInitGroup | current | The group of objects that report the full initializations counters for current PM intervals. | |
| 1.3.6.1.2.1.10.1.8.1.20 | Groupadsl2PMLineCurrInitShortGroup | current | The group of objects that report the short initializations counters for current PM intervals. | |
| 1.3.6.1.2.1.10.1.8.1.21 | Groupadsl2PMLineHist15MinGroup | current | The group of line level PM counters for the previous 15 minutes intervals. | |
| 1.3.6.1.2.1.10.1.8.1.22 | Groupadsl2PMLineHist1DayGroup | current | The group of line level PM counters for the previous 24 hours intervals. | |
| 1.3.6.1.2.1.10.1.8.1.23 | Groupadsl2PMLineInitHist15MinGroup | current | The group of PM counters for the previous 15 minutes intervals full initializations. | |
| 1.3.6.1.2.1.10.1.8.1.24 | Groupadsl2PMLineInitHist15MinShortGroup | current | The group of PM counters for the previous 15 minutes intervals short initializations. | |
| 1.3.6.1.2.1.10.1.8.1.25 | Groupadsl2PMLineInitHist1DayGroup | current | The group of PM counters for the previous 24 hours intervals full initializations. | |
| 1.3.6.1.2.1.10.1.8.1.26 | Groupadsl2PMLineInitHist1DayShortGroup | current | The group of PM counters for the previous 24 hours intervals short initializations. | |
| 1.3.6.1.2.1.10.1.8.1.27 | Groupadsl2PMChCurrGroup | current | The group of objects that report the channel level counters for current PM intervals. | |
| 1.3.6.1.2.1.10.1.8.1.28 | Groupadsl2PMChHist15MinGroup | current | The group of objects that report the channel level counters for previous 15 minutes PM intervals. | |
| 1.3.6.1.2.1.10.1.8.1.29 | Groupadsl2PMChHist1DGroup | current | The group of objects that report the channel level counters for previous 24 hours PM intervals. | |
| 1.3.6.1.2.1.10.1.8.1.30 | Groupadsl2ScalarSCGroup | current | The group of objects that report the available memory resources for DELT processes. | |
| 1.3.6.1.2.1.10.1.8.1.31 | Groupadsl2ThreshNotificationGroup | current | This group supports notifications of significant conditions associated with ADSL2 lines. | |
| 1.3.6.1.2.1.10.1.8.1.32 | Groupadsl2StatusChangeNotificationGroup | current | This group supports notifications of thresholds crossing associated with ADSL2 lines. | |
| 1.3.6.1.2.1.10.1.8.2 | Nodeadsl2Compliances | |||
| 1.3.6.1.2.1.10.1.8.2.1 | Complianceadsl2LineMibCompliance | current | The compliance statement for SNMP entities which manage ADSL2 interfaces. |