PAIRGAIN-APS-MIB
32 objects
The module defines the PairGain Proprietary linear APS1+1 MIB used in the Avidia System
Imported Objects
| PAIRGAIN-COMMON-HD-MIB | pgApsMIB |
| PAIRGAIN-DSLAM-CHASSIS-MIB | TimeSeconds |
| RFC-1212 | OBJECT-TYPE |
| RFC1213-MIB | ifIndex |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE TimeTicks |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.927.1.9.12.1 | IdentitypgAps | The module defines the PairGain Proprietary linear APS1+1 MIB used in the Avidia System | ||
| 1.3.6.1.4.1.927.1.9.12.1.0 | NodepgApsMIBNotifications | |||
| 1.3.6.1.4.1.927.1.9.12.1.0.1 | NotificationpgApsTrapSwitchOver | current | If pgApsTrapEnable is enabled, then pgApsTrapSwitchOver is sent when the APS switches from the working channel to the protection channel or from the protection… | |
| 1.3.6.1.4.1.927.1.9.12.1.1 | NodepgApsMibObjects | |||
| 1.3.6.1.4.1.927.1.9.12.1.1.1 | TablepgApsConfigTable | not-accessible | current | This table provides the Automatic Protection Switch Mode Configuration for Linear 1+1 mode APS |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1 | RowpgApsConfigEntry | not-accessible | current | Entries in the pgApsConfigTable table. |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.1 | ColumnpgApsIndex | read-only | current | APS entries are slot based. The index uses the slot number of the card. pgApsIndex (slot number) identifies the APS 1+1 entry that represents the two APS 1+1 c… |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.2 | ColumnpgApsEnable | read-write | current | Enable (1) or disables (2) the APS feature. The default is disabled (2). |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.3 | ColumnpgApsTrapEnable | read-write | current | Enables (1) or disables (2) the sending of the trap whenever an APS switch occurs. The default is disabled (2). |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.4 | ColumnpgApsWorkChanIfIndex | read-only | current | The ifIndex of the 1+1 APS configuration working channel. |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.5 | ColumnpgApsProtChanIfIndex | read-only | current | The ifIndex of the 1+1 APS configuration protection channel. |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.6 | ColumnpgApsConfigMode | read-write | current | nonRevertive(1) : Default. non-Revertive mode as defined in GR-253 nonRevertiveAuto(2) : PairGain proprietary mode that switches from the working channel to th… |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.7 | ColumnpgApsConfigSigDegradeThresh | read-only | current | The Bit Error Rate threshold at which the APS declares that the currently selected signal has degraded. The value is the minus power of 10. For example, a valu… |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.8 | ColumnpgApsConfigWaitToRevert | read-write | current | This object is only used during 'revertive' switching mode: If the switch has occurred and the error condition has disappeared, then number of seconds specifie… |
| 1.3.6.1.4.1.927.1.9.12.1.1.1.1.9 | ColumnpgApsSwitchCommand | read-write | current | Sends a local switch command. For example, a command could be Manual switch from normal to protection, or Forced switch from normal to protection. The command … |
| 1.3.6.1.4.1.927.1.9.12.1.1.2 | TablepgApsStatusTable | not-accessible | current | This table provides the status for each 1+1 APS entry. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1 | RowpgApsStatusEntry | not-accessible | current | Status entry for each 1+1 APS. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.1 | ColumnpgApsStatusK1K2Rx | read-only | current | The value of the K1 K2 SONET overhead bytes received. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.2 | ColumnpgApsStatusK1K2Tx | read-only | current | The value of the K1 K2 SONET overhead bytes transmitted. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.3 | ColumnpgApsStatusCurrent | read-only | current | The current switch status. 0 means the working channel selected 1 means protection channel selected The default is the working channel (0). |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.4 | ColumnpgApsWorkChanStatus | read-only | current | Bit 0 set means that this channel is locked out and will not be switched. Bit 1 set means that the SD state is in effect on this channel Bit 2 set means that t… |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.5 | ColumnpgApsWorkChanLastSwitch | read-only | current | Time stamp of the last time the working channel switched to the protection channel. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.6 | ColumnpgApsWorkChanSDs | read-only | current | Running count of the number of SD conditions for the working channel that the driver detected. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.7 | ColumnpgApsWorkChanSFs | read-only | current | Running count of the number of SF conditions for the working channel that the driver detected. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.8 | ColumnpgApsWorkNumSwitchOvers | read-only | current | The number of times the working channel has switched to the protection channel. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.9 | ColumnpgApsProtChanStatus | read-only | current | The protection channel status: Bit 0 set means that the protection channel is locked out and will not be switched. Bit 1 set means that the SD state is in effe… |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.10 | ColumnpgApsProtChanLastSwitch | read-only | current | Time stamp of the last time the Protection channel switched to the working channel. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.11 | ColumnpgApsProtChanSDs | read-only | current | Running count of the number of SD conditions for the protection channel that the driver detected. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.12 | ColumnpgApsProtChanSFs | read-only | current | Running count of the number of SF conditions for the protection channel that the driver detected. |
| 1.3.6.1.4.1.927.1.9.12.1.1.2.1.13 | ColumnpgApsProtNumSwitchOvers | read-only | current | The number of times the protection channel switched to the working channel. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Byte | INTEGER (0..255) | ||
| PgApsK1K2 | Integer32 | current | This Textual Convention describes the K1K2 overhead bytes in the SONET frame that controls APS. K1 is located in the low order byte, K2 is located in the higher order second byte. Bits 1-4 of the K1 byte indicate a requ… |