PAIRGAIN-SDSLCELL-MIB
82 objects
The module defines the SDSL CELL MIB
Imported Objects
| PAIRGAIN-COMMON-HD-MIB | pgainSDSLCell |
| RFC-1212 | OBJECT-TYPE |
| RFC1213-MIB | ifIndex |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE |
| SNMPv2-TC | DisplayString RowStatus TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.927.1.14.1 | IdentitypgsdslCellMIB | The module defines the SDSL CELL MIB | ||
| 1.3.6.1.4.1.927.1.14.1.1 | NodepgsdslCellMibObjects | |||
| 1.3.6.1.4.1.927.1.14.1.1.1 | TablepgSdslCellLineTable | not-accessible | current | This table contains the information pointers used to configure each physical line/port of the SDSL Cell card. Each line/port is assigned the index of a Line Pr… |
| 1.3.6.1.4.1.927.1.14.1.1.1.1 | RowpgSdslCellLineEntry | not-accessible | current | This entry contains the indexes of the Line and Alarm Profiles that are assigned to the physical interface indexed by the ifIndex. |
| 1.3.6.1.4.1.927.1.14.1.1.1.1.1 | ColumnpgSdslCellLineProfile | read-write | current | The value of this object identifies the row in the Cell SDSL Line Configuration Profile Table, (pgSdslCellLineProfileTable), which applies for this Cell SDSL l… |
| 1.3.6.1.4.1.927.1.14.1.1.1.1.2 | ColumnpgSdslCellAlarmProfile | read-write | current | The value of this object identifies the row in the Cell SDSL Line Alarm Configuration Profile Table, (pgSdslCellLineAlarmProfileTable), which applies to this C… |
| 1.3.6.1.4.1.927.1.14.1.1.2 | TablepgSdslCellPhysTable | not-accessible | current | This table provides one row for each port. Each row contains the Physical Layer Parameters table for that port. |
| 1.3.6.1.4.1.927.1.14.1.1.2.1 | RowpgSdslCellPhysEntry | not-accessible | current | An entry in the pgSdslCellPhysTable. |
| 1.3.6.1.4.1.927.1.14.1.1.2.1.1 | ColumnpgSdslCellInvSerialNumber | read-only | current | Vendor specific string that identifies the vendor equipment. |
| 1.3.6.1.4.1.927.1.14.1.1.2.1.2 | ColumnpgSdslCellInvVendorID | read-only | current | The vendor ID assigned by T1E1.413 according to its Annex D. |
| 1.3.6.1.4.1.927.1.14.1.1.2.1.3 | ColumnpgSdslCellInvVersionNumber | read-only | current | Vendor specific Version number |
| 1.3.6.1.4.1.927.1.14.1.1.2.1.4 | ColumnpgSdslCellCurrSnrMgn | read-only | current | Noise Margin as seen by this ATU with respect to its received signal in tenth dB. |
| 1.3.6.1.4.1.927.1.14.1.1.2.1.5 | ColumnpgSdslCellCurrAtn | read-only | current | Measured difference in the total power transmitted by the peer and the total power received by this end. This is measured in in tenth dB. |
| 1.3.6.1.4.1.927.1.14.1.1.2.1.6 | ColumnpgSdslCellCurrStatus | read-only | current | Status indicates the state of the Port. This value is intended to give more detail than is currently available through the ifOperStatus. UP (1) - SDSL line is … |
| 1.3.6.1.4.1.927.1.14.1.1.3 | ScalarpgSdslCellLineProfileIndexNext | read-only | current | This object contains an appropriate value to be used for pgSdslCellLineProfileIndex when creating entries in the pgSdslCellLineProfileTable. The value '0' indi… |
| 1.3.6.1.4.1.927.1.14.1.1.4 | TablepgSdslCellLineProfileTable | not-accessible | current | This table contains information on the Cell-SDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to confi… |
| 1.3.6.1.4.1.927.1.14.1.1.4.1 | RowpgSdslCellLineProfileEntry | not-accessible | current | Each entry consists of a list of parameters that represents the configuration of an SDSL Cell. A profile is created in one step with all necessary parameter va… |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.1 | ColumnpgSdslCellLineProfileIndex | read-write | current | This object is used by the line configuration table in order to identify a row of this table |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.2 | ColumnpgSdslCellLineProfileRowStatus | read-write | current | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active… |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.3 | ColumnpgSdslCellLineCode | read-write | current | Specifies the SDSL coding type used on this line. Other types may be added in the future. |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.4 | ColumnpgSdslCellLineRateMode | read-write | current | Defines what form of transmit rate adaptation is configured on this port. See chipset description for more information. |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.5 | ColumnpgSdslCellLineRate | read-write | current | Defines the rate of this port , if RateMode is set to fixed |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.6 | ColumnpgSdslCellLineTermType | read-write | current | Defines the mode of the transceiver ,intend for testing only |
| 1.3.6.1.4.1.927.1.14.1.1.4.1.7 | ColumnpgSdslCellLineProfileInUse | read-only | current | Defines whether this profile is in use. The agent must insure that this object is up to date whenever the line table is updated. If the implementator of this M… |
| 1.3.6.1.4.1.927.1.14.1.1.5 | ScalarpgSdslCellAlarmProfileIndexNext | read-only | current | This object contains an appropriate value to be used for pgSdslCellAlarmProfileIndex when creating entries in the pgSdslCellAlarmProfileTable. The value '0' in… |
| 1.3.6.1.4.1.927.1.14.1.1.6 | TablepgSdslCellAlarmProfileTable | not-accessible | current | This table contains information on the Cell-SDSL Alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to conf… |
| 1.3.6.1.4.1.927.1.14.1.1.6.1 | RowpgSdslCellAlarmProfileEntry | not-accessible | current | Each entry consists of a list of parameters that represents the Alarm configuration of an Cell SDSL port. A profile is created in one step with all necessary p… |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.1 | ColumnpgSdslCellAlarmProfileIndex | read-write | current | This object is used by the line alarm configuration table in order to identify a row of this table |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.2 | ColumnpgSdslCellAlarmProfileRowStatus | read-write | current | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active… |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.3 | ColumnpgSdslCellThresh15MinLOSS | read-write | current | The number of Loss of Signal Seconds, encountered by an Cell SDSL interface within any given 15 minutes performance data collection period, which causes the SN… |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.4 | ColumnpgSdslCellThresh15MinLOCD | read-write | current | The number of Loss of Cell Delineation, encountered by an Cell SDSL interface within any given 15 minutes performance data collection period, which causes the … |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.5 | ColumnpgSdslCellThresh15MinSLOCD | read-write | current | The number of Severe Loss of Cell Delineation, encountered by an Cell SDSL interface within any given 15 minutes performance data collection period, which caus… |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.6 | ColumnpgSdslCellThreshSNR | read-write | current | The SNR value below which causes the SNMP agent to send a pgSdslCellSNRThreshTrap. Limit of one trap will be sent for any TBD interval. A value of '0' will dis… |
| 1.3.6.1.4.1.927.1.14.1.1.6.1.7 | ColumnpgSdslCellAlarmProfileInUse | read-only | current | Defines whether this profile is in use. The agent must insure that this object is up to date whenever the line table is updated. If the implementator of this M… |
| 1.3.6.1.4.1.927.1.14.1.1.7 | TablepgSdslCellPerfCurrTable | not-accessible | current | This table contains running counters on the Cell-SDSL Line performance data. These counters will rollover after overflow. These counters are used internally fo… |
| 1.3.6.1.4.1.927.1.14.1.1.7.1 | RowpgSdslCellPerfCurrEntry | not-accessible | current | An Entry in pgSdslCellPerfCurrTable |
| 1.3.6.1.4.1.927.1.14.1.1.7.1.1 | ColumnpgSdslCellPerfCurrLOSS | read-only | current | The number of Loss of Signal seconds, encountered by an Cell SDSL interface since powered up or since last cleared with a clear command |
| 1.3.6.1.4.1.927.1.14.1.1.7.1.2 | ColumnpgSdslCellPerfCurrLOCD | read-only | current | The number of Loss of Cell Delineation, encountered by an Cell SDSL interface since powered up or since last cleared with a clear command |
| 1.3.6.1.4.1.927.1.14.1.1.7.1.3 | ColumnpgSdslCellPerfCurrSLOCD | read-only | current | The number of Severe Loss of Cell Delineation, encountered by an Cell SDSL interface since powered up or since last cleared with a clear command |
| 1.3.6.1.4.1.927.1.14.1.1.7.1.4 | ColumnpgSdslCellClearStats | read-write | current | Clear running statistics counters to zero on this particular port. Writing a '1' to this MIB object only clears the counters present in pgSdslCellPerfCurrTable… |
| 1.3.6.1.4.1.927.1.14.1.1.7.1.5 | ColumnpgSdslCellStatsLastCleared | read-only | current | The value of MIB II's sysUpTime object at the last time these statistics were cleared. At power on, this value should contain 0. |
| 1.3.6.1.4.1.927.1.14.1.1.8 | TablepgSdslCellPerfCurr15MinTable | not-accessible | current | This table contains information on the Cell-SDSL Line performance data for the current 15 minute period |
| 1.3.6.1.4.1.927.1.14.1.1.8.1 | RowpgSdslCellPerfCurr15MinEntry | not-accessible | current | An Entry in pgSdslCellPerfCurr15MinTable |
| 1.3.6.1.4.1.927.1.14.1.1.8.1.1 | ColumnpgSdslCellPerfCurr15MinLOSS | read-only | current | The number of Loss of Signal seconds, encountered by an Cell SDSL interface within current 15 minutes performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.8.1.2 | ColumnpgSdslCellPerfCurr15MinLOCD | read-only | current | The number of Loss of Cell Delineation, encountered by an Cell SDSL interface within current 15 minutes performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.8.1.3 | ColumnpgSdslCellPerfCurr15MinSLOCD | read-only | current | The number of Severe Loss of Cell Delineation, encountered by an Cell SDSL interface within current 15 minutes performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.8.1.4 | ColumnpgSdslCellClearHistory | read-write | current | Writing a '1' to this object clears all of the statistics and history counters related to this port (ifIndex) except for the running counters stored in pgSdslC… |
| 1.3.6.1.4.1.927.1.14.1.1.8.1.5 | ColumnpgSdslCellHistoryLastCleared | read-only | current | The value of MIB II's sysUpTime object at the last time the history was cleared. At power on, this value should contain 0. |
| 1.3.6.1.4.1.927.1.14.1.1.9 | TablepgSdslCellPerf15MinIntervalTable | not-accessible | current | This table contains information on the Cell-SDSL Line performance data for the previous (0-96) 15 minute Interval |
| 1.3.6.1.4.1.927.1.14.1.1.9.1 | RowpgSdslCellPerf15MinIntervalEntry | not-accessible | current | An Entry in pgSdslCellPerf15MinIntervalTable |
| 1.3.6.1.4.1.927.1.14.1.1.9.1.1 | ColumnpgSdslCellPerf15MinIntervalIndex | read-only | current | A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours and 45 minutes prior … |
| 1.3.6.1.4.1.927.1.14.1.1.9.1.2 | ColumnpgSdslCellPerf15MinIntervalLOSS | read-only | current | The number of Loss of Signal seconds , encountered by an Cell SDSL interface within this 15 minutes performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.9.1.3 | ColumnpgSdslCellPerf15MinIntervalLOCD | read-only | current | The number of Loss of Cell Delineation , encountered by an Cell SDSL interface within this 15 minutes performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.9.1.4 | ColumnpgSdslCellPerf15MinIntervalSLOCD | read-only | current | The number of severe Loss of Cell Delineation , encountered by an Cell SDSL interface within this 15 minutes performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.10 | TablepgSdslCellPerfCurr24hTable | not-accessible | current | This table contains information on the Cell-SDSL Line performance data for the current 24 hour period |
| 1.3.6.1.4.1.927.1.14.1.1.10.1 | RowpgSdslCellPerfCurr24hEntry | not-accessible | current | An Entry in pgSdslCellPerfCurr24hTable |
| 1.3.6.1.4.1.927.1.14.1.1.10.1.1 | ColumnpgSdslCellPerfCurr24hLOSS | read-only | current | The number of Loss of Signal seconds, encountered by an Cell SDSL interface within current 24 hour performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.10.1.2 | ColumnpgSdslCellPerfCurr24hLOCD | read-only | current | The number of Loss of Cell Delineation, encountered by an Cell SDSL interface within current 24 hour performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.10.1.3 | ColumnpgSdslCellPerfCurr24hSLOCD | read-only | current | The number of Severe Loss of Cell Delineation, encountered by an Cell SDSL interface within current 24 hour performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.11 | TablepgSdslCellPerf24hIntervalTable | not-accessible | current | This table contains information on the Cell-SDSL Line performance data for the previous 7 24 hour Interval |
| 1.3.6.1.4.1.927.1.14.1.1.11.1 | RowpgSdslCellPerf24hIntervalEntry | not-accessible | current | An Entry in pgSdslCellPerf24hIntervalTable |
| 1.3.6.1.4.1.927.1.14.1.1.11.1.1 | ColumnpgSdslCellPerf24hIntervalIndex | read-only | current | A number between 1 and 7, where 1 is the most recently completed 24 hour interval |
| 1.3.6.1.4.1.927.1.14.1.1.11.1.2 | ColumnpgSdslCellPerf24hIntervalLOSS | read-only | current | The number of Loss of Signal seconds , encountered by an Cell SDSL interface within this 24 hour performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.11.1.3 | ColumnpgSdslCellPerf24hIntervalLOCD | read-only | current | The number of Loss of Cell Delineation , encountered by an Cell SDSL interface within this 24 hour performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.11.1.4 | ColumnpgSdslCellPerf24hIntervalSLOCD | read-only | current | The number of severe Loss of Cell Delineation , encountered by an Cell SDSL interface within this 24 hour performance data collection interval |
| 1.3.6.1.4.1.927.1.14.1.1.12 | TablepgSdslCellAlarmTable | not-accessible | current | This table provides the SDSL Cell alarm indications. |
| 1.3.6.1.4.1.927.1.14.1.1.12.1 | RowpgSdslCellAlarmEntry | not-accessible | current | Entries of the SDSL Cell alarm table |
| 1.3.6.1.4.1.927.1.14.1.1.12.1.1 | ColumnpgSdslCellCrossThreshLOSS | read-only | current | When active the LOSS Threshold was crossed during the previous 15 minute interval and the condition has not yet been cleared. |
| 1.3.6.1.4.1.927.1.14.1.1.12.1.2 | ColumnpgSdslCellCrossThreshLOCD | read-only | current | When active the LOCD Threshold was crossed during the previous 15 minute interval and the condition has not yet been cleared. |
| 1.3.6.1.4.1.927.1.14.1.1.12.1.3 | ColumnpgSdslCellCrossThreshSLOCD | read-only | current | When active the SLOCD Threshold was crossed during the previous 15 minute interval and the condition has not yet been cleared. |
| 1.3.6.1.4.1.927.1.14.1.1.12.1.4 | ColumnpgSdslCellCrossThreshSNR | read-only | current | When active the current SNR is below the SNR Threshold. |
| 1.3.6.1.4.1.927.1.14.1.1.12.1.5 | ColumnpgSdslCellHardwareCause | read-only | current | This MIB object is used to communicate a port based hardware failure. 1 = no failure detected 2 = transceiver failure detected. e.g. failure to communicate wit… |
| 1.3.6.1.4.1.927.1.14.1.1.12.1.6 | ColumnpgSdslCellAlarmLastChanged | read-only | current | The value of MIB II's sysUpTime object at the last time the alarm status changed. At power on, this value should contain 0. |
| 1.3.6.1.4.1.927.1.14.1.2 | NodepgSdslCellTraps | |||
| 1.3.6.1.4.1.927.1.14.1.2.0 | NodepgSdslCellTrap | |||
| 1.3.6.1.4.1.927.1.14.1.2.0.1 | NotificationpgSdslCellThreshLOSSTrap | current | Loss of Signal 15-minute interval threshold exceeded | |
| 1.3.6.1.4.1.927.1.14.1.2.0.2 | NotificationpgSdslCellThreshLOCDTrap | current | Loss of Cell Delineation 15-minute interval threshold exceeded | |
| 1.3.6.1.4.1.927.1.14.1.2.0.3 | NotificationpgSdslCellThreshSLOCDTrap | current | Severe Loss of Cell Delination 15-minute interval threshold exceeded | |
| 1.3.6.1.4.1.927.1.14.1.2.0.4 | NotificationpgSdslCellThreshSNRTrap | current | SNR 15-minute interval threshold exceeded | |
| 1.3.6.1.4.1.927.1.14.1.2.0.5 | NotificationpgSdslCellHardwareFaultTrap | current | A hardware fault on this ifIndex has occurred. The pgSdslCellHardware Cause provides a description of the type of the failure. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PgSdslcellAlarmProfileType | INTEGER(0..65535) | ||
| PgSdslcellLineProfileType | INTEGER(0..65535) |