PEA-BRIDGE-IPDSLAM
389 objects
The IP DSLAM software supports a number of standard and proprietary MIBs. This MIB module defines objects for the management via SNMP of the bridge functionality in the IP DSLAM. The bridge filter functionality from the IP DSLAM is configurable not only per subscriber but also per PVC for a specific subscriber. All the subscribers connected to a specific IP DSLAM share the same physically Ethernet interface, and to protect the subscribers from each other (e.g. from hacking and spoofing) the bridge is implemented with some proprietary filters. One of these filters is a VLAN ID filter. With the use of this filter it is possible to limit the VLAN IDs that a end-user is allowed to use. The filter is implemented as Access Control Lists, so the same filter can be attached to several end-users. For further information about this filter please see the description of the following parameters: - vlanIdAclTable - vlanIdAclRuleTable - pvcUpstreamVlanIdAclId - pvcDownstreamVlanIdAclId This mib contains subscriberInfoTable which contains a list of subscriber information that the IP-DSLAM has dynamically learned. From the table it is possible to read out following information of the subscriber : - MAC address - IP address - virtual MAC address - DHCP lease time - whether subscriber uses fixed forwarding functionality - gateway IP address - gateway MAC address This mib contains the mcastFilterTable which contains multicast filter information for a PVC. Each entry describes a range of consecutive multicast group addresses which are allowed or disallowed. Each multicast group address range is mapped to a multicast Vlan and priority. This mib contains the broadcastStormControl and multicastStormControl which protect the network from upstream broadcast/multicast storms. They will limit the traffic to the thresholds, broadcastStormControlThreshold multicastStormControlThreshold respectively. They can be enabled/disabled with broadcastStormControl multicastStormControl respectively Traffic with all 48 bits in MAC address set to 1 is checked by broadcastStormControl. Traffic that is not broadcast, but with ethernet multicast bit set, is checked by multicastStormControl.
Imported Objects
| DIESEL-SMI | peaIpDslam |
| INET-ADDRESS-MIB | InetAddress InetAddressType InetPortNumber |
| SNMPv2-SMI | Counter32 Counter64 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DateAndTime MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.193.72.300.30 | IdentitypeaBridgeIpDslam | The IP DSLAM software supports a number of standard and proprietary MIBs. This MIB module defines objects for the management via SNMP of the bridge functionali… | ||
| 1.3.6.1.4.1.193.72.300.30.1 | NodebridgeControl | |||
| 1.3.6.1.4.1.193.72.300.30.1.1 | ScalarlineIndex | not-accessible | current | The ADSL subscriber line index. |
| 1.3.6.1.4.1.193.72.300.30.1.2 | ScalarpvcIndex | not-accessible | current | The PVC index. |
| 1.3.6.1.4.1.193.72.300.30.1.3 | TablepvcTable | not-accessible | current | A list of entries to the PVCs. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1 | RowpvcEntry | not-accessible | current | An entry containing PVCs objects for the subscriber line identified by lineIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.1 | ColumnvlanID | read-write | current | This is the VLANID to be used for the Ethernet traffic (accordingly to 802.1Q) from and to the specified PVC. It is only used if vlanOperation is set to addone… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.2 | Columnpriority | read-write | current | The priority (accordingly to 802.1Q) that should be used for the Ethernet frames to and from the specified PVC. It is only used if vlanOperation is set to addo… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.3 | ColumnpvcStatus | read-only | current | Show the result of the latest 'ATM OAM F5 end-to-end loopback' test. - notUsed: missing PVC configuration - at least peakCellRate has to be specified - lineDow… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.4 | ColumnaccessMethod | read-write | current | Determines which access method to use for the specific PVC. 0 - DHCP = Use a dynamic IP address (using DHCP). 1 - Static IP = Use a static IP address. 2 - Tran… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.6 | ColumnallowBroadcast | read-write | current | If True the subscriber is allowed to send and receive all broadcasts on the specified PVC. NOTE: Make special attention toward configuring the correct VLANID f… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.7 | ColumngatewayFixedForwarding | read-write | current | If True the Ethernet frames originated from the specified PVC will be forwarded to a gateway. The value can be either True(1) or False(2). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.8 | ColumngatewayIP | read-write | current | The IP Address of the gateway to be used. The value can be any IP address. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.9 | ColumnuseDHCP | read-write | obsolete | If True the DHCP server is used for allocation of IP address. The value can be either True(1) or False(2). If DHCP is not used, an IP address should be added t… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.10 | ColumndownstreamFrameCount | read-only | current | The number of Ethernet frames sent downstream. This equals the number of AAL5 frames transmitted. The counter is stored in remotestorage and will survive a res… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.11 | ColumnupstreamFrameCount | read-only | current | The number of Ethernet frames sent upstream. This equals the number of AAL5 frames received. The counter is stored in remotestorage and will survive a restart. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.12 | ColumndownstreamByteCount | read-only | current | The downstream traffic payload measured in bytes. This counts the number of bytes transmitted within AAL5 frames, excluding the 6 bytes overhead added by AAL5 … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.13 | ColumnupstreamByteCount | read-only | current | The uptream traffic payload measured in bytes. This counts the number of bytes received within AAL5 frames, excluding the 6 bytes overhead added by AAL5 itself… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.14 | Columnvpi | read-write | current | The Virtual Path Identifier for the specified PVC of a subscriber line. The VPI and VCI identifies the PVC (Permanent Virtual Circuit). The value can be betwee… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.15 | Columnvci | read-write | current | The Virtual Chanel Identifier for the specified PVC of a subscriber line. The VCI and VPI identifies the PVC (Permanent Virtual Circuit). The value can be betw… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.16 | ColumnsustainableCellRate | read-write | current | The average downstream PVC rate. The rate has to be lower or equal to the configured ADSL rate and in steps of 32000 bps. Notice: To carry telephony over IP, 1… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.17 | ColumnpeakCellRate | read-write | current | The peak downstream PVC rate. The rate has to be lower or equal to the configured ADSL rate and in steps of 32000 bps. Notice: To carry telephony over IP, 1920… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.18 | ColumntransparentBridging | read-write | obsolete | If True NO filtering will be performed on the specific PVC. This option gives FULL Layer2 connectivity. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.19 | ColumnrelayAgentConfiguration | read-write | current | Determines which Relay Agent configuration to use (DHCP or PPPoE). DHCP: The relay agent adds DHCP option 82 to upstream DHCP requests, and removes the option … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.20 | ColumnrelayAgentString | read-write | current | Specifies the string used in some relayAgentConfiguration's (see 'relayAgentConfiguration' description). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.21 | ColumnuseICMPSecurity | read-write | current | If true upstream ICMP messages are filtered to avoid denial of service attacks. The value can be either True(1) or False(2). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.22 | ColumnatmServiceCategory | read-write | current | Determines which atm service category to use for the PVC. 0 - UBR = Unspecified bit rate. This is typically used for data applications. 1 - VBR NRT = Variable … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.23 | ColumndownstreamMaximumBurstSize | read-write | current | The maximum number of cells in a burst. Notice: To allow a complete telephony over IP packet to be included in one burst, 4 atm cells are needed. Furthermore, … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.24 | ColumnupstreamPeakCellRate | read-write | current | The peak upstream PVC rate. The rate has to be lower or equal to the configured ADSL rate and in steps of 32000 bps. Notice: To carry telephony over IP, 192000… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.25 | ColumnupstreamSustainableCellRate | read-write | current | The average upstream PVC rate. The rate has to be lower or equal to the configured ADSL rate and in steps of 32000 bps. Notice: To carry telephony over IP, 192… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.26 | ColumnupstreamMaximumBurstSize | read-write | current | The maximum number of cells in a burst. Notice: To allow a complete telephony over IP packet to be included in one burst, 4 atm cells are needed. Furthermore, … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.27 | ColumnvirtualMacAdressesAllowed | read-write | deprecated | Use 1.3.6.1.4.1.193.72.300.30.1.3.1.38, macAddressCountLimit and 1.3.6.1.4.1.193.72.300.30.1.3.1.37, virtualMacEnable in place of this. Deprecated from: EDA 2.… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.28 | ColumnallowIgmpSnooping | read-write | current | If True IGMP Snooping is enabled on the specified PVC. The value can be either True(1) or False(2). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.29 | ColumnencapsulationProtocol | read-only | current | The encapsulation protocol used on top of the AAL5, according to RFC2684. The value is autodetected based on the packets received from the CPE modem. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.30 | ColumnpppVariant | read-only | current | The actual PPP variant chosen based on the packets received from the CPE modem. The value is only valid if accessMethod is set to pppox (5). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.31 | ColumnmulticastGroupsAllowed | read-write | deprecated | Multicast groups which are within the range are allowed. If the multicastGroupsAllowed string is empty, then all multicast groups are allowed. Each range is 8 … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.32 | ColumndiscardedOversizedFrames | read-write | current | Counts the number of frames, which have been discarded, due to excessive frame length. The counter can be reset by writing a '0'. (See also: MaximumEthernetFra… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.33 | ColumnupstreamPolicing | read-write | current | Upstream Policing can be enabled or disabled on the specific PVC True(1) - ENABLED False(2) - DISABLED. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.34 | ColumnupstreamPolicingCntr | read-write | current | Counts the number of frames, which have been discarded, due to Upstream Policing. The counter can be reset by writing a '0'. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.35 | ColumnfloodMulticastAddrs | read-write | current | Multicast groups which are within the range are flooded on all member PVCs and LAN. If the floodMulticastAddrs string is empty, then all multicast packets are … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.36 | ColumnpppMruSubstitution | read-write | current | Using this parameter it is possible to 'trick' the CPE modem to think the BRAS uses a MRU of for instance 1500 bytes (Which it usually can). This can be used t… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.37 | ColumnvirtualMacEnable | read-write | current | Activates the function that exchanges the MAC addresses in the frames that pass, so that only virtual MAC addresses, chosen by the access network are used with… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.38 | ColumnmacAddressCountLimit | read-write | current | A limit for the number of MAC addresses concurrently in use in PVC. Special rules apply when it is set to 0. If virtual MAC functionality is enabled when it is… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.39 | ColumninnerVlanID | read-write | current | This is the VLAN identifier used only if vlanOperation is configured to addtwotags. This is the inner Vlan used on traffic from and to the specified PVC. The v… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.40 | ColumninnerVlanPriority | read-write | current | The VLAN priority used only if vlanOperation value is configured to addtwotags. This priority is associated with vlanInnerID accordingly to 802.1Q. The value c… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.41 | ColumndhcpStatus | read-only | current | Indicates the result of testing availability of DHCP Server support within connection. The value is updated only during an IP Connectivity Test, which runs upo… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.42 | ColumngatewayStatus | read-only | current | Indicates the result of testing reachability of default gateway for connection. The value is updated only during an IP Connectivity Test, which runs upon initi… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.43 | ColumnipConnectivityTest | read-write | current | Control and state of IP Connectivity. Values: standBy (0) DSLAM is between tests. This is the default value. This value is written by client when test is finis… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.44 | ColumninsertMacInDhcpOption | read-write | current | DHCP option code to be used when inserting the end-user MAC address to DHCP messages from the end-user. The end-user MAC is inserted in a site-specific DHCP op… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.45 | ColumnmulticastGroupsLimit | read-write | current | A parameter which gives the upper limit on the number of Multicast Groups a subscriber can join simultaneously. When exceeded the subscriber will be denied the… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.46 | ColumnvlanTag | read-write | current | Defines the VLAN tag type applied on upstream traffic if. In case of two VLAN tags applied the this VLAN tag type is applied to the outer VLAN tag - qtag: Q/Qi… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.47 | ColumninnerVlanTag | read-write | current | Defines the inner VLAN tag type applied on upstream traffic if. - qtag: Q/QinQ VLAN tagging. (Ethernet Type 0x8100) - vmantag: VMAN VLAN tagging. (Ethernet Typ… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.48 | ColumnvlanOperation | read-write | current | This parameter defines the VLAN operation for the specific PVC. The following values are supported: - addzerotags: The end-users VLAN tags are forwarded transp… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.49 | ColumnvlanFilter | read-write | current | Defines the types of VLAN tagging a user is allowed to use on upstream traffic. The upstream traffic passes a VLAN filter and if the outermost VLAN tag in the … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.50 | ColumnvlanPrioMappingPrio0 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.51 | ColumnvlanPrioMappingPrio1 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.52 | ColumnvlanPrioMappingPrio2 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.53 | ColumnvlanPrioMappingPrio3 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.54 | ColumnvlanPrioMappingPrio4 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.55 | ColumnvlanPrioMappingPrio5 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.56 | ColumnvlanPrioMappingPrio6 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.57 | ColumnvlanPrioMappingPrio7 | read-write | obsolete | It is possible to map the priority in a user-provided VLAN to another or the priority in the VLAN(s) applied by the IP DSLAM e.g. if the priority in the user-p… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.58 | ColumndownstreamFlows | read-write | current | A list of downstream flows that are contained in/use this PVC. Each octet is a number of a flow that exists (is active). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.59 | ColumnupstreamFlows | read-write | current | A list of upstream flows that are contained in/use this PVC. Each octet is a number of a flow that exists (is active). |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.60 | ColumnflowIdentificationCriterionDownstream | read-write | current | When packets arrive on the uplink, the DSLAM needs to determine which flow the packet belongs to. This can be done in one of three ways. I.e by looking at ... … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.61 | ColumnflowIdentificationCriterionUpstream | read-write | current | When packets arrive on a DSL line, the DSLAM needs to determine which flow the packet belongs to. This can be done in one of four ways. I.e by looking at ... c… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.62 | ColumnschedulingScheme | read-write | current | The DSLAM may schedule packets in this flow in competition with packets in other flows in the same PVC. none (0) There is only one flow, no scheduling needed. … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.63 | ColumnfloodDownstreamUnknownDestMac | read-write | current | Frames received from the aggregation network will be forwarded on this PVC if the destination MAC address is unknown to the DSLAM. The frame must be received i… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.64 | Columnl2cpTunneling | read-write | current | This parameter is used to enable Layer 2 Protocol Tunneling. The tunneling mechanism is a propritary solution specified by Cisco. The Layer 2 Control Protocol … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.65 | ColumnupstreamMcastEnable | read-write | current | Setting this parameter to True enables the end-user to send IGMP queries and multicast streams in the VLAN associated with the PVC. Valid from: EDA 2.1 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.66 | ColumnclearDhcpLeaseTable | read-write | current | When set to clear, all the DHCP Mapping entries for this Connection will be removed from the DHCP Mapping Table. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.67 | ColumnclearMACHistory | read-write | current | If True Clear the Subscriber MAC History for this pCon(Line,Pvc). The value can be either True(1) or False(2). Default Value will be false. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.68 | ColumngatewayMacfilteringDirection | read-write | current | A parameter which gives on which traffic the Gateway Mac filtering needs to be done. If the value is set to 0 then the only in the upstream the Gateway Mac wil… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.69 | ColumndownstreamFramesPerSecond | read-only | current | A parameter which gives the number of downstream frames received on the PVC per second. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.70 | ColumnupstreamFramesPerSecond | read-only | current | A parameter which gives the number of upstream frames received on the PVC per second. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.71 | ColumndownstreamBitsPerSecond | read-only | current | A parameter which gives the number of downstream bits received on the PVC per second. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.72 | ColumnupstreamBitsPerSecond | read-only | current | A parameter which gives the number of upstream bits received on the PVC per second. |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.73 | ColumnarpProxyConfig | read-write | current | This parameter decides the behavior of the ArpProxy in the IP-DSLAM. It is only valid when forced forwarding is enabled (peaBridgeIpDslam::gatewayFixedForwardi… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.80 | ColumnendUserVlanOperation | read-write | current | This parameter decides how the end-users VLAN tags should be handled. The possible values are 0 endUserVLanForward End-user VLANs are filtered according to the… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.85 | ColumnvlanIdFilter | read-write | deprecated | Defines the VLAN ID a user is allowed to use on upstream traffic. The upstream traffic passes a VLAN ID filter and if the outermost VLAN ID in the received pac… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.90 | ColumnpvcFilterVersion | read-write | current | Detemines which version of the IP filter to use for the specific PVC. 1 - pvcFilter = Use filters defined in pvcFiltersTable. 2 - accessControlList = Use Acces… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.93 | ColumnpvcUpstreamVlanIdAclId | read-write | current | Setting this value to non-zero will specify the VLAN ID ACL to be used in the upstream direction. The value of zero means no VLAN ID ACL is used for this PVC. … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.94 | ColumnpvcDownstreamVlanIdAclId | read-write | current | Setting this value to non-zero will specify the VLAN ID ACL to be used in the downstream direction. The value of zero means no VLAN ID ACL is used for this PVC… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.95 | ColumnpvcUpstreamEtherTypeAclId | read-write | current | Setting this value to non-zero will specify the EtherType ACL to be used in the upstream direction. The value of zero means no EtherType ACL is used for this P… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.100 | ColumnpvcDownstreamEtherTypeAclId | read-write | current | Setting this value to non-zero will specify the EtherType ACL to be used in the downstream direction. The value of zero means no EtherType ACL is used for this… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.105 | ColumnpvcUpstreamIpAclId | read-write | current | Setting this value to non-zero will specify the IP ACL to be used in the upstream direction. The value of zero means no IP ACL is used for this PVC. Default va… |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.110 | ColumnpvcDownstreamIpAclId | read-write | current | Setting this value to non-zero will specify the IP ACL to be used in the downstream direction. The value of zero means no IP ACL is used for this PVC. Default … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.115 | ColumndhcpServerMacAddress | read-write | current | Use this parameter to convert the end-users DHCP messages from broadcast to unicast. This is very usefull when trying to minimise the amount of broadcast in a … |
| 1.3.6.1.4.1.193.72.300.30.1.3.1.120 | ColumnallowAnonymousMulticastSubscriber | read-write | current | Determines whether MAC and IP address validation is performed when a subscriber sends multicast frames upstream in the network. Example: If a subscriber is con… |
| 1.3.6.1.4.1.193.72.300.30.1.4 | TablepvcFiltersTable | not-accessible | current | A list of entries to the PVCs. |
| 1.3.6.1.4.1.193.72.300.30.1.4.1 | RowpvcFiltersEntry | not-accessible | current | An entry containing the filters for a PVC for the subscriber line identified by lineIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.1 | ColumnupsteamEthernetTypesFilterType | read-only | deprecated | The filter type can be positive(0) or negative(1). If positive all packets with EthernetType which are part of the filter entries are allowed by the filter. If… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.2 | ColumnupsteamEthernetTypesFilterValue | read-write | deprecated | Filter on Ethernet Type in packets from subscriber into network. A list of EthernetType entries, each two byte in network byte order (big endian). Example: Eth… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.3 | ColumnupstreamDestinationIpFilterType | read-write | deprecated | The filter type can be positive(0) or negative (1). If positive all packets with the destination IP which are part of the filter entries are allowed by the fil… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.4 | ColumnupstreamDestinationIpFilterValue | read-write | deprecated | Filter on destination IP in packets from subscriber into network. Filter entries 8 bytes each, representing a range - to represent the range >=10.0.0.0 <=16.0.… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.5 | ColumnupstreamSourcePortFilterType | read-only | deprecated | The filter type is negative (1). The filter allows all packets except the packets with the IP source port number which are part of the filter entries. This par… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.6 | ColumnupstreamSourcePortFilterValue | read-write | deprecated | Filter on IP source port number in packets from subscriber into network. Filter entries 2 bytes each - to exclude FTP add 21 = 0x00 0x15 This parameter is depr… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.7 | ColumnupstreamDestinationPortFilterType | read-only | deprecated | The filter type is negative (1). The filter allows all packets except the packets with the IP destination port number which are part of the filter entries. Thi… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.8 | ColumnupstreamDestinationPortFilterValue | read-write | deprecated | Filter on IP destination port number in packets from subscriber into network. Filter entries 2 bytes each - to exclude FTP add 21 = 0x00 0x15 This parameter is… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.9 | ColumndownsteamEthernetTypesFilterType | read-only | deprecated | The filter type can be positive(0) or negative(1). If positive all packets with EthernetType which are part of the filter entries are allowed by the filter. If… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.10 | ColumndownsteamEthernetTypesFilterValue | read-write | deprecated | Filter on Ethernet Type in packets from network to subscriber. A list of EthernetType entries, each two byte in network byte order (big endian). Example: Ether… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.11 | ColumndownstreamSourceIpFilterType | read-write | deprecated | The filter type can be positive(0) or negative (1). If positive all packets with the source IP which are part of the filter entries are allowed by the filter. … |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.12 | ColumndownstreamSourceIpFilterValue | read-write | deprecated | Filter on source IP in packets from network to subscriber. Filter entries 4 bytes each, representing a single address. To represent the adress 10.0.0.0 add 0x0… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.13 | ColumndownstreamSourcePortFilterType | read-only | deprecated | The filter type is negative (1). The filter allows all packets except the packets with the IP source port number which are part of the filter entries. This par… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.14 | ColumndownstreamSourcePortFilterValue | read-write | deprecated | Filter on IP source port number in packets from network to subscriber. Filter entries 2 bytes each - to exclude FTP add 21 = 0x00 0x15 This parameter is deprec… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.15 | ColumndownstreamDestinationPortFilterType | read-only | deprecated | The filter type is negative (1). The filter allows all packets except the packets with the IP destination port number which are part of the filter entries. Thi… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.16 | ColumndownstreamDestinationPortFilterValue | read-write | deprecated | Filter on IP destination port number in packets from network to subscriber. Filter entries 2 bytes each - to exclude FTP add 21 = 0x00 0x15 This parameter is d… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.17 | ColumnsubscriberMACFilterType | read-only | current | The filter type is positive(0). All packets with the MAC addresses which are part of the filter entries are allowed by the filter. |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.18 | ColumnsubscriberMACFilterValue | read-write | current | Filter on subscriber MAC addresses. At least one entry should apply here if DHCP is not used. Filter entries 6 bytes each - to include 00-80-03-04-05-06 add 0x… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.19 | ColumnsubscriberIpFilterType | read-write | deprecated | The subscriber IP filter type can be either positive(0) or disabled(2). If positive all packets with the subscriber IP which are part of the filter entries are… |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.20 | ColumnsubscriberIpFilterValue | read-write | deprecated | Filter on subscriber IP addresses. When using DHCP the entries in the filter are added automatically according to the DHCP leases. For other access methods IP … |
| 1.3.6.1.4.1.193.72.300.30.1.4.1.21 | ColumnupstreamPortIpFilterValue | read-write | deprecated | Filter on TCP/UDP destination port number as well as destination IP address in packets from subscriber into network. Filter entries are 10 bytes each. The firs… |
| 1.3.6.1.4.1.193.72.300.30.1.5 | ScalarvirtualMacAddressDomain | read-write | current | The virtual Mac address domain specifies 6 of the 8 bits in the first byte in the virtual Mac address. (The remaining two bits are the multicast bit and the gl… |
| 1.3.6.1.4.1.193.72.300.30.1.6 | ScalarmaximumEthernetFrameSize | read-write | current | MaximumEthernetFrameSize specifies the maximum frame size that the IP DSLAM will send up-stream in the access network. Longer frames will be discarded! The spe… |
| 1.3.6.1.4.1.193.72.300.30.1.7 | TablelineTable | not-accessible | current | A list of entries to the Line Table. |
| 1.3.6.1.4.1.193.72.300.30.1.7.1 | RowlineEntry | not-accessible | current | An entry containing Line objects for the subscriber line identified by lineIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.7.1.1 | ColumnenableAutoConfiguration | read-write | current | Enable of ILMI Auto Configuration for the Line. If True, ILMI AC will try to configure the CPE with all existing PVC:s for the line. |
| 1.3.6.1.4.1.193.72.300.30.1.7.1.5 | ColumnbroadcastStormControl | read-write | current | Broadcast Storm Control (BSC) function. The threshold is set using broadcastStormControlThreshold. The function is default disabled. The possible values are 0 … |
| 1.3.6.1.4.1.193.72.300.30.1.7.1.10 | ColumnbroadcastStormControlThreshold | read-write | current | When broadcastStormControlThreshold is passed and broadcastStormControl is enabled, all broadcast traffic is limited to broadcastStormControlThreshold. Broadca… |
| 1.3.6.1.4.1.193.72.300.30.1.7.1.15 | ColumnmulticastStormControl | read-write | current | Multicast Storm Control (MSC) function. The threshold is set using multicastStormControlThreshold. The function is default disabled. The possible values are 0 … |
| 1.3.6.1.4.1.193.72.300.30.1.7.1.20 | ColumnmulticastStormControlThreshold | read-write | current | When multicastStormControlThreshold is passed and multicastStormControl is enabled, all multicast traffic is limited to multicastStormControlThreshold. Multica… |
| 1.3.6.1.4.1.193.72.300.30.1.8 | ScalarvirtualMacAddressNodeId | read-write | current | The virtual Mac address Node ID specifies the last 3 bytes in the virtual Mac address. With the Node ID, it is possible to identify the origin of an ethernet f… |
| 1.3.6.1.4.1.193.72.300.30.1.9 | ScalarvlanTagType | read-write | current | If 1, VLAN tagging is single. If 2, VLAN tagging is double. Valid from: EDA 2.0SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.10 | ScalarvirtualMacAddressNodeIdEx | read-write | current | The virtual Mac address 'Node ID Extended' specifies 26 bits in the virtual Mac address. With the Node ID Extended, it is possible to identify the origin of an… |
| 1.3.6.1.4.1.193.72.300.30.1.11 | ScalarrelayAgentEdaIp | read-write | current | IP address inserted in the relay agent information when remoteIdEda is used (see 'relayAgentConfiguration' description). Zero must be used when the IP-DSLAM is… |
| 1.3.6.1.4.1.193.72.300.30.1.12 | ScalarrelayAgentEdaNodeId | read-write | current | Specifies the NodeId inserted in the relay agent information when remoteEdaId is used (see 'relayAgentConfiguration' description). The layout of the NodeId fie… |
| 1.3.6.1.4.1.193.72.300.30.1.13 | ScalarflowIndex | not-accessible | current | Unique number assigned to each flow within PVC. The highest index is 7 upstream and 3 downstream. Please note that flowIndex affects priority scheduling and bu… |
| 1.3.6.1.4.1.193.72.300.30.1.14 | TabledownstreamFlowConfigTable | not-accessible | current | A list of downstream flows |
| 1.3.6.1.4.1.193.72.300.30.1.14.1 | RowdownstreamFlowConfigEntry | not-accessible | current | An entry containing flows identified by lineIndex, pvcIndex and flowIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.14.1.2 | ColumndfcFlowIdentifyingValues | read-write | current | What values (in CoS or DSCP field) signal that the packet belongs to this flow. One octet per value. A packet that contains one of these values is classified a… |
| 1.3.6.1.4.1.193.72.300.30.1.14.1.3 | ColumndfcPolicingEnable | read-write | current | Is this flow to be policed? |
| 1.3.6.1.4.1.193.72.300.30.1.14.1.4 | ColumndfcSustainableDataRate | read-write | current | The maximum allowed average information rate in the flow. The rate must be lower than or equal to the configured ADSL rate and in steps of 32000 bps. Notice: T… |
| 1.3.6.1.4.1.193.72.300.30.1.14.1.5 | ColumndfcMaxBurst | read-write | current | The maximum number of bytes in a burst. Notice: To allow a complete telephony over IP packet to be included in one burst, 250 bytes are needed. Furthermore, if… |
| 1.3.6.1.4.1.193.72.300.30.1.14.1.6 | ColumndfcBytesPerRound | read-write | current | The DRR scheduling algorithm visits all the queues in the PVC in a circular fashion (round robin). For each turn of the circle it transfers dfcBytesPerRound by… |
| 1.3.6.1.4.1.193.72.300.30.1.14.1.7 | ColumndfcMaxQueueBuffers | read-write | current | The maximum number of packet buffers allowed to be placed in queue for one downstream flow queue |
| 1.3.6.1.4.1.193.72.300.30.1.15 | TabledownstreamFlowStatsTable | not-accessible | current | Statistics information for a list of downstream flows |
| 1.3.6.1.4.1.193.72.300.30.1.15.1 | RowdownstreamFlowStatsEntry | not-accessible | current | An entry containing flows identified by lineIndex, pvcIndex and flowIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.15.1.1 | ColumndfsPolicedPacketCount | read-only | current | The number of packets that have been discarded by the policing mechanism. |
| 1.3.6.1.4.1.193.72.300.30.1.15.1.2 | ColumndfsFrameCount | read-only | current | The number of Ethernet frames that have passed. |
| 1.3.6.1.4.1.193.72.300.30.1.15.1.3 | ColumndfsByteCount | read-only | current | The number of bytes that have passed. |
| 1.3.6.1.4.1.193.72.300.30.1.15.1.4 | ColumndfsPolicedBytesCount | read-only | current | The number of bytes that have been discarded by the policing mechanism. |
| 1.3.6.1.4.1.193.72.300.30.1.15.1.5 | ColumndfsMaxQueueUsage | read-write | current | The maximum number of buffers stored in a downstream flow queue at any time since the counter was reset. Zero is the only value that can be written to dfsMaxQu… |
| 1.3.6.1.4.1.193.72.300.30.1.16 | TableupstreamFlowConfigTable | not-accessible | current | A list of upstream flows |
| 1.3.6.1.4.1.193.72.300.30.1.16.1 | RowupstreamFlowConfigEntry | not-accessible | current | An entry containing flows identified by lineIndex, pvcIndex and flowIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.16.1.2 | ColumnufcFlowIdentifyingValues | read-write | current | What values (in CoS or DSCP field) signal that the packet belongs to this flow. One octet per value. A packet that contains one of these values is classified a… |
| 1.3.6.1.4.1.193.72.300.30.1.16.1.3 | ColumnufcPolicingEnable | read-write | current | Is this flow to be policed? |
| 1.3.6.1.4.1.193.72.300.30.1.16.1.4 | ColumnufcSustainableDataRate | read-write | current | The maximum allowed average data rate in the flow. The rate must be lower than or equal to the configured ADSL rate and in steps of 32000 bps. Notice: To carry… |
| 1.3.6.1.4.1.193.72.300.30.1.16.1.5 | ColumnufcMaxBurst | read-write | current | The maximum number of bytes in a burst. Notice: To allow a complete telephony over IP packet to be included in one burst, 250 bytes are needed. Furthermore, if… |
| 1.3.6.1.4.1.193.72.300.30.1.16.1.6 | ColumnufcCosRemarkEnable | read-write | obsolete | Is the CoS/p-bit value in the Ethernet header to be overwritten? This MIB object may be removed. Obsoleted from: EDA 2.2 SP1 |
| 1.3.6.1.4.1.193.72.300.30.1.16.1.7 | ColumnufcExceedingTrafficFlow | read-write | current | One Flow has one VLAN priority value associated, that VLAN priority value will be written in the outer most VLAN tag of the Ethernet frame before the Ethernet … |
| 1.3.6.1.4.1.193.72.300.30.1.17 | TableupstreamFlowStatsTable | not-accessible | current | Statistics information for a list of upstream flows |
| 1.3.6.1.4.1.193.72.300.30.1.17.1 | RowupstreamFlowStatsEntry | not-accessible | current | An entry containing flows identified by lineIndex, pvcIndex and flowIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.17.1.1 | ColumnufsPolicedPacketCount | read-only | current | The number of packets that have been discarded by the policing mechanism. |
| 1.3.6.1.4.1.193.72.300.30.1.17.1.2 | ColumnufsFrameCount | read-only | current | The number of Ethernet frames that have passed. |
| 1.3.6.1.4.1.193.72.300.30.1.17.1.3 | ColumnufsByteCount | read-only | current | The number of bytes that have passed. |
| 1.3.6.1.4.1.193.72.300.30.1.17.1.4 | ColumnufsPolicedBytesCount | read-only | current | The number of bytes that have been discarded by the policing mechanism. |
| 1.3.6.1.4.1.193.72.300.30.1.18 | NodemcastFilter | |||
| 1.3.6.1.4.1.193.72.300.30.1.18.1 | TablemcastFilterTypeTable | not-accessible | current | A list of entries to the multicast filter type list. |
| 1.3.6.1.4.1.193.72.300.30.1.18.1.1 | RowmcastFilterTypeEntry | not-accessible | current | The lineIndex and pvcIndex pair forms a unique identification of a PVC in the managed device. A mcastFilterTypeEntry contains multicast filter type information… |
| 1.3.6.1.4.1.193.72.300.30.1.18.1.1.1 | ColumnmcastFilterType | read-write | current | Specifies whether the multicast filter is positive or negative. If the multicast filter is positive, the managed device is allowed to forward multicast group I… |
| 1.3.6.1.4.1.193.72.300.30.1.18.2 | TablemcastFilterTable | not-accessible | current | A list of entries to the multicast filter list. |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1 | RowmcastFilterEntry | not-accessible | current | The lineIndex and pvcIndex pair forms a unique identification of a PVC in the managed device. A mcastFilterEntry contains multicast filter information for a PV… |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1.1 | ColumnmcastFilterAddressType | read-only | current | The type of Internet address used in the multicast filter address range. |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1.2 | ColumnmcastFilterFirstAddress | read-only | current | The first address in the multicast group Internet address range. The type of this address is determined by the value of the mcastFilterAddressType object. The … |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1.3 | ColumnmcastFilterLastAddress | read-create | current | The last address in the multicast group Internet address range. The type of this address is determined by the value of the mcastFilterAddressType object. mcast… |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1.8 | ColumnmcastFilterVlanID | read-create | current | The Vlan ID to be used for the multicast traffic on a multicast group Internet address range, from and to the specified PVC. The value -1 is a nil-value indica… |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1.13 | ColumnmcastFilterVlanPriority | read-create | current | The priority (accordingly to 802.1Q) that should be used for the multicast frames to and from the specified PVC. The value can be between 0 and 7 (where 7 is t… |
| 1.3.6.1.4.1.193.72.300.30.1.18.2.1.99 | ColumnmcastFilterRowStatus | read-create | current | The mcastFilterRowStatus is used to manage the creation and deletion of rows in mcastFilterTable. |
| 1.3.6.1.4.1.193.72.300.30.1.19 | TablemacHistoryTable | not-accessible | current | A list of MAC address entries of Subscribers disconnected/connected to IP DSLAM |
| 1.3.6.1.4.1.193.72.300.30.1.19.1 | RowmacHistoryEntry | not-accessible | current | An entry containing the Subscriber MAC address for each connection identified by the lineIndex and pvcIndex. |
| 1.3.6.1.4.1.193.72.300.30.1.19.1.1 | ColumnsubscriberMacAddress | read-only | current | MAC address of the subscriber. |
| 1.3.6.1.4.1.193.72.300.30.1.19.1.2 | ColumnsubscriberMacLastSeen | read-only | current | The timestamp which indicates the time when the Subscriber MAC address was last seen. |
| 1.3.6.1.4.1.193.72.300.30.1.19.1.3 | ColumnsubscriberMacStatus | read-only | current | If Active indicates that the subscriber is currently connected and Inactive shows the MAC of a disconnected subscriber. The value can be either Active(1) or In… |
| 1.3.6.1.4.1.193.72.300.30.1.20 | ScalarmacFilterAgedTime | read-write | current | macFilterAgedTime specifies in seconds the maximum age of inactive MAC address entries in the subscriber MAC filter for access methods PPPoE and TLS. |
| 1.3.6.1.4.1.193.72.300.30.1.21 | NodeaccessControlList | |||
| 1.3.6.1.4.1.193.72.300.30.1.21.4 | TablevlanIdAclTable | not-accessible | current | This table maintains a list of VLAN ID Access Control Lists in the IPDSLAM. Each Access Control List is made up of a group of access rules. The access rules ar… |
| 1.3.6.1.4.1.193.72.300.30.1.21.4.5 | RowvlanIdAclEntry | not-accessible | current | An entry in the vlanIdAclTable. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.21.4.5.1 | ColumnvlanIdAclId | read-only | current | Index of the VLAN ID Access Control List. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.21.4.5.5 | ColumnvlanIdAclNumberOfRules | read-only | current | Total number of rules in the VLAN ID Access Control List (ACL). Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.21.4.5.999 | ColumnvlanIdAclRowStatus | read-create | current | This object is used to manage the creation, deletion and modification of rows in the VLAN ID Access Control List Table. Due to the way SNMP is handled in the I… |
| 1.3.6.1.4.1.193.72.300.30.1.21.6 | TablevlanIdAclRuleTable | not-accessible | current | This table is used to add/delete individual access rule statement in an VLAN ID Access Control List. The order of the rules is very important. The rules are pr… |
| 1.3.6.1.4.1.193.72.300.30.1.21.6.5 | RowvlanIdAclRuleEntry | not-accessible | current | An entry in the VLAN ID ACL Rule Table. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.21.6.5.1 | ColumnvlanIdAclRuleIndex | read-only | current | The Access Control List may have multiple rules. The vlanIdAclRuleIndex specifies the position of the particular rule in the ACL. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.21.6.5.5 | ColumnvlanIdAclMatchAction | read-create | current | Indicates the action to be taken when packet meets the filtering condition in an ACL Rule. permit: Every packet that matches rule condition is forwarded for fu… |
| 1.3.6.1.4.1.193.72.300.30.1.21.6.5.10 | ColumnvlanIdAclVlanIdMin | read-create | current | vlanIdAclVlanIdMin is 12 bit VLAN ID (0 to 4095) which defines the first element of the intended VLAN ID range. vlanIdAclVlanIdMin and vlanIdAclVlanIdMax toget… |
| 1.3.6.1.4.1.193.72.300.30.1.21.6.5.15 | ColumnvlanIdAclVlanIdMax | read-create | current | vlanIdAclVlanIdMax is 12 bit VLAN ID (0 to 4095) which defines the last element of the intended VLAN ID range. vlanIdAclVlanIdMin and vlanIdAclVlanIdMax togeth… |
| 1.3.6.1.4.1.193.72.300.30.1.21.6.5.999 | ColumnvlanIdAclRuleRowStatus | read-create | current | This object is used to manage creation, deletion and modification of rows in the Access Control List Rule Table. Due to the way SNMP is handled in the IPDSLAM … |
| 1.3.6.1.4.1.193.72.300.30.1.21.10 | TableetherTypeAclTable | not-accessible | current | This table maintains a list of EtherType Access Control Lists in the IPDSLAM. Each Access Control List is made up of a group of access rules. The access rules … |
| 1.3.6.1.4.1.193.72.300.30.1.21.10.5 | RowetherTypeAclEntry | not-accessible | current | An entry in the etherTypeAclTable. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.10.5.1 | ColumnetherTypeAclId | read-only | current | Index of the EtherType Access Control List. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.10.5.5 | ColumnetherTypeAclNumberOfRules | read-only | current | Total number of rules in the EtherType Access Control List (ACL). Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.10.5.999 | ColumnetherTypeAclRowStatus | read-create | current | This object is used to manage the creation, deletion and modification of rows in the EtherType Access Control List Table. Due to the way SNMP is handled in the… |
| 1.3.6.1.4.1.193.72.300.30.1.21.15 | TableetherTypeAclRuleTable | not-accessible | current | This table is used to add/delete individual access rule statement in an EtherType Access Control List. The order of the rules is very important. The rules are … |
| 1.3.6.1.4.1.193.72.300.30.1.21.15.5 | RowetherTypeAclRuleEntry | not-accessible | current | An entry in the EtherType ACL Rule Table. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.15.5.1 | ColumnetherTypeAclRuleIndex | read-only | current | The Access Control List may have multiple rules. The ipAclRuleIndex specifies the position of the particular rule in the ACL. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.15.5.5 | ColumnetherTypeAclMatchAction | read-create | current | Indicates the action to be taken when packet meets the filtering condition in an ACL Rule. permit: Every packet that matches rule condition is forwarded for fu… |
| 1.3.6.1.4.1.193.72.300.30.1.21.15.5.10 | ColumnetherTypeAclEtherType | read-create | current | This number indicates the Ethernet type to match to have a match on the rule. Zero means any Ethernet type will match the rule. A list of standardized Ethernet… |
| 1.3.6.1.4.1.193.72.300.30.1.21.15.5.999 | ColumnetherTypeAclRuleRowStatus | read-create | current | This object is used to manage creation, deletion and modification of rows in the Access Control List Rule Table. Due to the way SNMP is handled in the IPDSLAM … |
| 1.3.6.1.4.1.193.72.300.30.1.21.30 | TableipAclTable | not-accessible | current | This table maintains a list of IP Access Control Lists in the IPDSLAM. Each Access Control List is made up of a group of access rules. The access rules are sto… |
| 1.3.6.1.4.1.193.72.300.30.1.21.30.5 | RowipAclEntry | not-accessible | current | An entry in the ipAclTable. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.30.5.1 | ColumnipAclId | read-only | current | Index of the IP Access Control List. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.30.5.5 | ColumnipAclNumberOfRules | read-only | current | Total number of rules in the IP Access Control List (ACL). Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.30.5.999 | ColumnipAclRowStatus | read-create | current | This object is used to manage the creation, deletion and modification of rows in the IP Access Control List Table. Due to the way SNMP is handled in the IPDSLA… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35 | TableipAclRuleTable | not-accessible | current | This table is used to add/delete individual access rule statement in an IP Access Control List. The order of the rules is very important. The rules are process… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5 | RowipAclRuleEntry | not-accessible | current | An entry in the IP ACL Rule Table. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.1 | ColumnipAclRuleIndex | read-only | current | The Access Control List may have multiple rules. The ipAclRuleIndex specifies the position of the particular rule in the ACL. Valid from: EDA 2.2 SP2 |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.5 | ColumnipAclMatchAction | read-create | current | Indicates the action to be taken when packet meets the filtering condition in an ACL Rule. permit: Every packet that matches rule condition is forwarded for fu… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.24 | ColumnipAclIpProtocol | read-create | current | ipAclIpProtocol identifies the layer above IP to which the IP packet data should be passed. The numbers associated with some important transport protocols are … |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.29 | ColumnipAclIpAddrType | read-create | current | The type of Internet address used in the ACL Rule. The ipAclIpAddrType will determine the value of ipAclSrcIpAddrMin, ipAclSrcIpAddrMax, ipAclDestIpAddrMin and… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.30 | ColumnipAclSrcIpAddrMin | read-create | current | ipAclSrcIpAddrMin is a 32-bit IP address (0.0.0.0 through 255.255.255.255), which defines the first element of the intended IP source address range. ipAclSrcIp… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.31 | ColumnipAclSrcIpAddrMax | read-create | current | ipAclSrcIpAddrMax is a 32-bit IP address (0.0.0.0 through 255.255.255.255), which defines the last element of the intended IP source address range. ipAclSrcIpA… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.36 | ColumnipAclDestIpAddrMin | read-create | current | ipAclDestIpAddrMin is a 32-bit IP address (0.0.0.0 through 255.255.255.255), which defines the first element of the intended IP destination address range. ipAc… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.37 | ColumnipAclDestIpAddrMax | read-create | current | ipAclDestIpAddrMax is a 32-bit IP address (0.0.0.0 through 255.255.255.255), which defines the last element of the intended IP destination address range. ipAcl… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.42 | ColumnipAclSrcPortOp | read-create | current | Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1) which is the default value, means that no comparison is to be made with th… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.43 | ColumnipAclSrcPort | read-create | current | The source port number of the TCP or UDP protocol. If the ipAclSrcPortOp is set to range(6), this object will be the starting port number of the port range. Th… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.44 | ColumnipAclSrcPortRange | read-create | current | The source port number of the TCP or UDP protocol. If the ipAclSrcPortOp is set to range(6), this object will be the ending port number of the port range. The … |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.49 | ColumnipAclDestPortOp | read-create | current | Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1) which is the default value, means that no comparison is to be made wi… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.50 | ColumnipAclDestPort | read-create | current | The destination port number of the TCP or UDP protocol. If the ipAclDestPortOp is set to range(6), this object will be the starting port number of the port ran… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.51 | ColumnipAclDestPortRange | read-create | current | The destination port number of the TCP or UDP protocol. If the ipAclDestPortOp is set to range(6), this object will be the ending port number of the port range… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.56 | ColumnipAclTcpFlags | read-create | current | Value of the TCP Control code/flags. The parameter specifies if a flag must be set or cleared to have a match. |MSB| | | | | | | LSB | | x | x | U | A | P | R … |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.57 | ColumnipAclTcpFlagsMask | read-create | current | Value of the TCP Control code/flags mask. The ipAclTcpFlagsMask specifies which of the TCP Control flags specified in tcpFlags to match. |MSB| | | | | | | LSB … |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.58 | ColumnipAclTcpFlagsMatchMethod | read-create | current | The ipAclTcpFlagsMatchMethod specified whether all (matchAll) or just one or more (matchAny) TCP flags must be correct to have a match in the TCP flags part of… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.63 | ColumnipAclIcmpType | read-create | current | Value of ICMP type. ICMP type defines the ICMP message that is being passed. The default value of -1 for ipAclIcmpType is used to match on all the ICMP Types. … |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.64 | ColumnipAclIcmpCode | read-create | current | Value of ICMP code. In certain cases, an ICMP type may have several submessages. A submessage is called an ICMP code. When an ICMP message requires only a type… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.69 | ColumnipAclIgmpType | read-create | current | Value of IGMP type. IGMP type defines the IGMP message that is being passed.The default value of -1 for ipAclIgmpType is used to match on all the IGMP Types. T… |
| 1.3.6.1.4.1.193.72.300.30.1.21.35.5.999 | ColumnipAclRuleRowStatus | read-create | current | This object is used to manage creation, deletion and modification of rows in the Access Control List Rule Table. Due to the way SNMP is handled in the IPDSLAM … |
| 1.3.6.1.4.1.193.72.300.30.1.22 | NodesubsIpFilter | |||
| 1.3.6.1.4.1.193.72.300.30.1.22.1 | TablesubsIpFilterTypeTable | not-accessible | current | A list of entries to the subscriber IP filter type list. |
| 1.3.6.1.4.1.193.72.300.30.1.22.1.1 | RowsubsIpFilterTypeEntry | not-accessible | current | The lineIndex and pvcIndex pair forms a unique identification of a PVC in the managed device. A subsIpFilterTypeEntry contains subscriber IP filter type inform… |
| 1.3.6.1.4.1.193.72.300.30.1.22.1.1.5 | ColumnsubsIpFilterType | read-write | current | Specifies whether the subscriber IP filter is positive or disabled. If the filter is positive, the managed device is allowed to forward traffic from/to subscri… |
| 1.3.6.1.4.1.193.72.300.30.1.22.2 | TablesubsIpFilterTable | not-accessible | current | A list of entries to the subscriber IP filter list. |
| 1.3.6.1.4.1.193.72.300.30.1.22.2.1 | RowsubsIpFilterEntry | not-accessible | current | The lineIndex and pvcIndex pair forms a unique identification of a PVC in the managed device. A subsIpFilterEntry contains subscriber IP filter information for… |
| 1.3.6.1.4.1.193.72.300.30.1.22.2.1.5 | ColumnsubsIpFilterAddressType | read-only | current | The type of Internet address used in the subscriber IP filter address range. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.22.2.1.10 | ColumnsubsIpFilterFirstAddress | read-only | current | The first address in the subscriber Internet address range. The type of this address is determined by the value of the subsIpFilterAddressType object. The subs… |
| 1.3.6.1.4.1.193.72.300.30.1.22.2.1.15 | ColumnsubsIpFilterLastAddress | read-create | current | The last address in the subscriber Internet address range. The type of this address is determined by the value of the subsIpFilterAddressType object. subsIpFil… |
| 1.3.6.1.4.1.193.72.300.30.1.22.2.1.99 | ColumnsubsIpFilterRowStatus | read-create | current | The subsIpFilterRowStatus is used to manage the creation and deletion of rows in subsIpFilterTable. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.24 | ScalarpriorityIndex | not-accessible | current | priorityIndex is used to access a number of tables regarding Weighted Random Early Discard (WRED). Those tables are indexed per line, PVC and VLAN priority ind… |
| 1.3.6.1.4.1.193.72.300.30.1.30 | TabledownstreamFlowWredConfigTable | not-accessible | current | The IP-DSLAM flow implementation allows multiple VLAN priorities to be mapped to the same downstream flow queue (downstream flows are configured with downstrea… |
| 1.3.6.1.4.1.193.72.300.30.1.30.5 | RowdownstreamFlowWredConfigEntry | not-accessible | current | This is an entry in the downstreamFlowWredConfigTable and contains the parameters to configure the WRED mechanism for one VLAN priority in the downstream flows… |
| 1.3.6.1.4.1.193.72.300.30.1.30.5.5 | ColumnwredBufferLimit | read-write | current | Weighted Random Early Discard (WRED) buffer limit specifies the queue usages limit for traffic with a specific VLAN priority. The drop limit is specified as a … |
| 1.3.6.1.4.1.193.72.300.30.1.30.5.10 | ColumnwredDropProbability | read-write | current | wredDropProbability is used to specify the probability that a packet with a specific VLAN priority will be dropped if the wredBufferLimit has been exceeded. wr… |
| 1.3.6.1.4.1.193.72.300.30.1.31 | TabledownstreamFlowWredStatisticsTable | not-accessible | current | The downstreamFlowWredStatisticsTable contains statistics counters for the Weighted Random Early Discard (WRED) mechanism. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.31.5 | RowdownstreamFlowWredStatisticsEntry | not-accessible | current | The downstreamFlowWredStatisticsEntry contains Weighted Random Early Discard (WRED) statistics for one VLAN priority in a downstream flow. Valid from: EDA 2.2 … |
| 1.3.6.1.4.1.193.72.300.30.1.31.5.5 | ColumnwredStatisticsPktsCount | read-only | current | The number of packets that have passed the Weighted Random Early Discard (WRED) mechanism. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.31.5.10 | ColumnwredStatisticsDiscards | read-only | current | The number of packets that have been discarded by the Weighted Random Early Discard (WRED) mechanism. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.31.5.15 | ColumnwredStatisticsByteCount | read-only | current | The number of bytes that have passed the Weighted Random Early Discard (WRED) mechanism. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.31.5.20 | ColumnwredStatisticsByteDiscards | read-only | current | The number of bytes that have been discarded by the Weighted Random Early Discard (WRED) mechanism. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.32 | TablesubscriberInfoTable | not-accessible | current | This table contains a list of subscriber information that the IP-DSLAM has dynamically learned. From the list it is possible to get the relationship between su… |
| 1.3.6.1.4.1.193.72.300.30.1.32.5 | RowsubscriberInfoEntry | not-accessible | current | An entry containing the subscriber information identified by lineIndex, pvcIndex, subscriberInfoMac and subscriberInfoIp address. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.5 | ColumnsubscriberInfoMac | read-only | current | The MAC address of the subscriber which is learned by the IP-DSLAM. Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.10 | ColumnsubscriberInfoIp | read-only | current | For StaticIP, DHCP and DHCPIP over ATM access methods, relationship between MAC address of the subscriber and IP address of the subscriber is maintained in the… |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.15 | ColumnsubscriberInfoVirtualMac | read-only | current | subscriberInfoVirtualMac will contain the virtual MAC address of the subscriber generated by the IP-DSLAM only when - peaBridgeIpDslam::virtualMacEnable is set… |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.20 | ColumnsubscriberInfoDhcpLeaseTime | read-only | current | The IP address lease time for the subscriber when DHCP is used as access method. For other access methods the DateAndTime string will be read out as empty. The… |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.25 | ColumnsubscriberInfoGatewayFixedForwarding | read-only | current | If True the Ethernet frames originated from the subscriber will be forwarded to a gateway. The value can be either True(1) or False(2). Valid from: EDA 2.2 R3A |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.30 | ColumnsubscriberInfoGatewayIp | read-only | current | The IP address of the gateway used by the subscriber. The subscriberInfoGatewayIp will contain 0.0.0.0 value when peaBridgeIpDslam::gatewayIp is not set for th… |
| 1.3.6.1.4.1.193.72.300.30.1.32.5.35 | ColumnsubscriberInfoGatewayMac | read-only | current | The MAC address of the gateway used by the subscriber which is learned by the IP-DSLAM. The subscriberInfoGatewayMac will contain 00:00:00:00:00:00 value when … |
| 1.3.6.1.4.1.193.72.300.30.1.36 | TablemcastGroupInfoTable | not-accessible | current | Table containing the IGMP membership information for each Multicast Group Address learned by IGMP Snooping. With IGMP Snooping enabled,the IP DSLAM can 'listen… |
| 1.3.6.1.4.1.193.72.300.30.1.36.1 | RowmcastGroupInfoEntry | not-accessible | current | A mcastGroupInfoEntry is created for each multicast group learned on a PVC, when any subscriber joins the multicast group. For an mcastGroupInfoEntry created b… |
| 1.3.6.1.4.1.193.72.300.30.1.36.1.1 | ColumnmcastGroupVlanId | read-only | current | This object indicates the VLAN in which the multicast group is learned. |
| 1.3.6.1.4.1.193.72.300.30.1.36.1.5 | ColumnmcastGroupAddress | read-only | current | This object indicates the IP address of the multicast group learned. |
| 1.3.6.1.4.1.193.72.300.30.1.36.1.9 | ColumnmcastGroupHostMACAddress | read-only | current | This object indicates the MAC address of the host which is a member of the Muticast Group. |
| 1.3.6.1.4.1.193.72.300.30.1.36.1.13 | ColumnmcastGroupSourceFilterIPAddress | read-only | current | IGMP Version 3 (IGMPv3) adds support for 'source filtering', which enables a multicast receiver host to explicitly signal sources from which they want to recei… |
| 1.3.6.1.4.1.193.72.300.30.1.36.1.21 | ColumnmcastGroupIgmpMsgType | read-only | current | This object indicates the type of IGMP messages that are transmitted and received for the Multicast Group. The values for different IGMP message types are : IG… |
| 1.3.6.1.4.1.193.72.300.30.1.36.1.25 | ColumnmcastGroupIgmpMsgUpTime | read-only | current | This object indicates the time elapsed since the mcastGroupIgmpMsgType was first received/transmitted. |
| 1.3.6.1.4.1.193.72.300.30.1.40 | NodetrafficStatistics | |||
| 1.3.6.1.4.1.193.72.300.30.1.40.1 | ScalarnodeId | not-accessible | current | The value of nodeId uniquely identifies the traffic statistics of the IPDSLAM. The default value for IPDSLAM is always one. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2 | NodetrafStatNode | |||
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1 | TabletrafStatNodeMainTable | not-accessible | current | This table contains list of upstream and downstream traffic statistics entries of IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1 | RowtrafStatNodeMainEntry | not-accessible | current | An entry is a collection of upstream and downstream traffic statistics kept for the IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.1 | ColumntsnDsPkts | read-only | current | Total number of Ethernet packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.5 | ColumntsnDsUntaggedMgmtPkts | read-only | current | Total number of untagged management packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.10 | ColumntsnDsTaggedMgmtPkts | read-only | current | Total number of tagged management packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.15 | ColumntsnDsDhcpPkts | read-only | current | Total number of non-management DHCP packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.20 | ColumntsnDsPppDiscoveryPkts | read-only | current | Total number of PPP discovery packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.25 | ColumntsnDsBcastPkts | read-only | current | Total number of non-management broadcast packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.30 | ColumntsnDsArpPkts | read-only | current | Total number of non-management ARP packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.35 | ColumntsnDsL2cpPkts | read-only | current | Total number of L2CP packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.40 | ColumntsnDsPktsFlooded | read-only | current | Total number of Ethernet packets from the network flooded to the subscribers in the same VLAN due to destination MAC address unknown in IPDSLAM. Valid from: ED… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.45 | ColumntsnUsPkts | read-only | current | Total number of packets received from the subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.50 | ColumntsnUsDhcpPkts | read-only | current | Total number of DHCP packets received from the subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.55 | ColumntsnUsPppDiscoveryPkts | read-only | current | Total number of PPP discovery packets received from the subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.60 | ColumntsnUsArpPkts | read-only | current | Total number of ARP packets received from the subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.65 | ColumntsnLocalSwitchPkts | read-only | current | Total number of Ethernet packets received from the subscriber and sent to other subscribers connected on the same IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.1.1.999 | ColumntsnMainClearStat | read-write | current | This parameter resets all the trafStatNodeMain traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5 | TabletrafStatNodeMcastMainTable | not-accessible | current | This table contains list of upstream and downstream multicast traffic statistics entries of IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1 | RowtrafStatNodeMcastMainEntry | not-accessible | current | An entry is a collection of upstream and downstream multicast traffic statistics kept for the IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.1 | ColumntsnDsMcastPkts | read-only | current | Total number of IP multicast packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.5 | ColumntsnDsMcastCtrlPkts | read-only | current | Total number of multicast control (Non-UDP) packets received from the network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.10 | ColumntsnUsMcastPkts | read-only | current | Total number of IP multicast packets received from the subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.15 | ColumntsnUsMcastCtrlPkts | read-only | current | Total number of multicast control (Non-UDP) packets received from the subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.20 | ColumntsnMcastPktsFlooded | read-only | current | Total number of multicast packets received which gets flooded to the network and subscribers in same VLAN. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.25 | ColumntsnNoOfIgmpGroups | read-only | current | Total number of IGMP Groups which have atleast one active member. IGMP Group is identified by the multicast group address and vlan. e.g 1) If IGMP Group [G1,V1… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.30 | ColumntsnNoOfIgmpEntries | read-only | current | Total number of IGMP entries for which there is - Atleast one active member. - Atleast one active querier. IGMP entry is identified by PVC, multicast group add… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.35 | ColumntsnIgmpQueryPkts | read-only | current | Total number of IGMP Query packets received either from network or subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.40 | ColumntsnIgmpReportPkts | read-only | current | Total number of IGMP Report packets received either from network or subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.45 | ColumntsnIgmpLeavePkts | read-only | current | Total number of IGMP Leave packets received either from network or subscribers. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.5.1.999 | ColumntsnMcastMainClearStat | read-write | current | This parameter resets all the trafStatNodeMcastMain traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9 | TabletrafStatNodeErrorsTable | not-accessible | current | This table contains list of upstream and downstream error traffic statistics of the IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1 | RowtrafStatNodeErrorsEntry | not-accessible | current | An entry is a collection of upstream and downstream error traffic statistics kept for the IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.1 | ColumntsnDsTotalDiscardPkts | read-only | current | Total number of non-multicast Ethernet packets from the network discarded by IPDSLAM. tsnDsTotalDiscardPkts = SUM[tsnDsUnknownDstPkts, tsnDsGatewayErrPkts, tsn… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.5 | ColumntsnDsUnknownDstPkts | read-only | current | Total number of Ethernet packets received from the network with unknown destination MAC address. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.10 | ColumntsnDsGatewayErrPkts | read-only | current | Total number of Ethernet packets received from the network and discarded due to : - gateway MAC address not resolved by the IPDSLAM - Source MAC address in the… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.15 | ColumntsnDsVlanIdAclErrPkts | read-only | current | Total number of Ethernet packets received from the network and discarded due to VLAN Id Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.20 | ColumntsnDsEthTypeAclErrPkts | read-only | current | Total number of Ethernet packets received from the network and discarded due to Ethernet type Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.25 | ColumntsnDsIpAclFilterErrPkts | read-only | current | Total number of IP packets received from the network and discarded due to IP Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.30 | ColumntsnUsTotalDiscardPkts | read-only | current | Total number of non-multicast Ethernet packets from the subscribers discarded by IPDSLAM. tsnUsTotalDiscardPkts = SUM[tsnUsVlanIdAclErrPkts, tsnUsEthTypeAclErr… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.35 | ColumntsnUsVlanIdAclErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers and discarded due to VLAN Id Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.40 | ColumntsnUsEthTypeAclErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers and discarded due to Ethernet type Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.45 | ColumntsnUsIpAclFilterErrPkts | read-only | current | Total number of IP packets received from the subscribers and discarded due to IP Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.50 | ColumntsnUsSrcMacErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers and discarded due to : - source MAC not present in the subscriber MAC filter. - MAC limit exceed… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.55 | ColumntsnUsSrcIpErrPkts | read-only | current | Total number of IP packets received from the subscribers and discarded due to source IP address filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.60 | ColumntsnUsBcastErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers and discarded due to subscriber not allowed to send and receive Broadcast. Valid from: EDA 2.2 S… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.65 | ColumntsnUsVmacErrPkts | read-only | current | Total number of packets received from the subscribers and discarded due to maximum limit reached for number of virtual MAC addresses. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.70 | ColumntsnUsGatewayErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers and discarded due to : - gateway MAC address not resolved by the IPDSLAM - Destination MAC addre… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.75 | ColumntsnUsSendErrPkts | read-only | current | Total number of non-multicast Ethernet packets received from the subscribers and discarded due to : - upstream policing - packet size exceeding peaBridgeIpDsla… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.80 | ColumntsnUsVlanTypeFltrErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers and discarded due to VLAN type filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.9.1.999 | ColumntsnErrorsClearStat | read-write | current | This parameter resets all the trafStatNodeErrors traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13 | TabletrafStatNodeMcastErrorsTable | not-accessible | current | This table contains list of upstream and downstream multicast error traffic statistics of the IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1 | RowtrafStatNodeMcastErrorsEntry | not-accessible | current | An entry is a collection of upstream and downstream multicast error traffic statistics kept for the IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.1 | ColumntsnDsMcastErrPkts | read-only | current | Total number of multicast packets received from the network and discarded due to : - Non-IP multicast packet - Non-L2CP multicast packet Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.5 | ColumntsnDsNoDestinationErrPkts | read-only | current | Total number of multicast UDP packets received from network and discarded due to unknown destination multicast group address. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.10 | ColumntsnDsIpAclErrPkts | read-only | current | Total number of multicast non-UDP packets received from network and discarded due to IP Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.15 | ColumntsnDsTxErrPkts | read-only | current | Total number of multicast packets received from network and discarded due to following errors in sending the packets to the susbcribers : - Illegal P-bit - Dow… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.20 | ColumntsnUsMcastErrPkts | read-only | current | Total number of multicast packets received from the subscribers and discarded due to : - Non-IP multicast packet - Non-L2CP multicast packet Valid from: EDA 2.… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.25 | ColumntsnUsNoDestinationErrPkts | read-only | current | Total number of multicast UDP packets received from the subscribers and discarded due to unknown destination multicast group address. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.30 | ColumntsnUsDisabledLogiPortErrPkts | read-only | current | Total number of multicast packets received from the susbcribers and discarded due to : - IGMP snooping disabled on the PVC. - Upstream multicast disabled on th… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.35 | ColumntsnUsIpAclErrPkts | read-only | current | Total number of multicast non-UDP packets received from the subscribers and discarded due to IP Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.40 | ColumntsnUsTxErrPkts | read-only | current | Total number of multicast packets received from the subscribers and discarded due to following errors in sending the packets to network. - upstream policing - … |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.45 | ColumntsnTooShortErrPkts | read-only | current | Total number of IGMP packets discarded due to packet size less than minimum IGMP packet length (Ethernet + IP + IGMP header). Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.50 | ColumntsnUnknownIgmpTypesErrPkts | read-only | current | Total number of IGMP packets discarded due to unknown IGMP type in the IGMP header. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.55 | ColumntsnPhyLayerNotRunningErrPkts | read-only | current | Total number of muticast packets received from the subscribers and discarded due to ADSL line being down. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.60 | ColumntsnReportsNotAllowedErrPkts | read-only | current | Total number of IGMP Report packets discarded due to : - IGMP Report received from the network and upstream multicast not enabled for any subscriber in same Vl… |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.65 | ColumntsnLeavesNotAllowedErrPkts | read-only | current | Total number of IGMP Leave packets discarded due to : - Multicast group address not allowed for the subscriber by the multicast filter. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.13.1.999 | ColumntsnMcastErrorsClearStat | read-write | current | This parameter resets all the trafStatNodeMcastErrors traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.17 | TabletrafStatNodeClearTable | not-accessible | current | This table contains tsnClearStat parameter which resets the upstream and downstream traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.17.1 | RowtrafStatNodeClearEntry | not-accessible | current | An entry in the trafStatNodeClearTable. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.2.17.1.1 | ColumntsnClearStat | read-write | current | This parameter resets all the following traffic statistics of the IPDSLAM to zero. - peaBridgeIpDslam::trafStatNodeMain - peaBridgeIpDslam::trafStatNodeMcastMa… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6 | NodetrafStatLogiPort | |||
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1 | TabletrafStatLogiPortMainTable | not-accessible | current | This table contains list of upstream and downstream traffic statistics of the IPDSLAM for a specific PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1 | RowtrafStatLogiPortMainEntry | not-accessible | current | An entry is a collection of upstream and downstream traffic statistics kept for the IPDSLAM for a specific PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.1 | ColumntslpDsPkts | read-only | current | Total number of Ethernet packets received from network and sent to the subscriber on the specified PVC. This parameter is an alias to pvcTable.downstreamFrameC… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.5 | ColumntslpDsBytes | read-only | current | Total number of bytes received from network and sent to the subscriber on the specified PVC. This parameter is an alias to pvcTable.downstreamByteCount. Valid … |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.10 | ColumntslpDsPktsPerSec | read-only | current | Total number of Ethernet packets per second received from network and sent to the subscriber on the specified PVC. This parameter is an alias to pvcTable.downs… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.15 | ColumntslpDsBitsPerSec | read-only | current | Total number of bits per second received from network and sent to the subscriber on the specified PVC. This parameter is an alias to pvcTable.downstreamBitsPer… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.20 | ColumntslpDsUcastPkts | read-only | current | Total number of unicast packets received from the network and sent to the subscriber on the specified PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.25 | ColumntslpDsBcastPkts | read-only | current | Total numbers of broadcast packets received from the network and sent to the subscriber on the specified PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.30 | ColumntslpDsFromLocalSrcPkts | read-only | current | Total numbers of packets received from a subscriber connected on the same IPDSLAM and sent to subscriber on the specified PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.35 | ColumntslpDsArpPkts | read-only | current | Total number of ARP packets received from network and sent to the subscriber on the specified PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.40 | ColumntslpDsDhcpPkts | read-only | current | Total number of DHCP packets received from network and sent to the subscriber on the specified PVC Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.45 | ColumntslpDsPppDiscoveryPkts | read-only | current | Total number of PPP discovery packets received from network and sent to the subscriber on the specified PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.50 | ColumntslpDsL2cpPkts | read-only | current | Total number of L2CP tunneling packets received from network and sent to the subscriber on the specified PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.55 | ColumntslpUsPkts | read-only | current | Total number of Ethernet packets received from the subscriber on the specified PVC and sent to the network. This parameter is an alias to pvcTable.upstreamFram… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.60 | ColumntslpUsBytes | read-only | current | Total number of bytes received from the subscriber on the specified PVC and sent to network. This parameter is an alias to pvcTable.upstreamByteCount. Valid fr… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.65 | ColumntslpUsPktsPerSec | read-only | current | Total number of Ethernet packets per second received from the subscriber on the specified PVC and sent to the network. This parameter is an alias to pvcTable.u… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.70 | ColumntslpUsBitsPerSec | read-only | current | Total number of bits per second received from the subscriber on the specified PVC and sent to network. This parameter is an alias to pvcTable.upstreamBitsPerSe… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.75 | ColumntslpUsUcastPkts | read-only | current | Total number of unicast packets received from the subscriber on the specified PVC and sent to network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.80 | ColumntslpUsBcastPkts | read-only | current | Total number of broadcast packets received from the subscriber on the specified PVC and sent to network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.85 | ColumntslpUsToLocalDestPkts | read-only | current | Total numbers of packets received from the subscriber on the specified PVC and sent to another subscriber connected on same IPDSLAM. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.90 | ColumntslpUsArpPkts | read-only | current | Total number of ARP packets received from the subscriber on the specified PVC and sent to network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.95 | ColumntslpUsDhcpPkts | read-only | current | Total number of DHCP packets received from the subscriber on the specified PVC and sent to network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.100 | ColumntslpUsPppDiscoveryPkts | read-only | current | Total number of PPP discovery packets received from the subscriber on the specified PVC and sent to network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.105 | ColumntslpUsL2cpPkts | read-only | current | Total number of L2CP tunneling packets received from the subscriber on the specified PVC and sent to network. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.1.1.999 | ColumntslpMainClearStat | read-write | current | This parameter resets all the trafStatLogiPortMain traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5 | TabletrafStatLogiPortErrorsTable | not-accessible | current | This table contains list of upstream and downstream error traffic statistics of the IPDSLAM for a specific PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1 | RowtrafStatLogiPortErrorsEntry | not-accessible | current | An entry is a collection of upstream and downstream error traffic statistics kept for the IPDSLAM for a specific PVC. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.1 | ColumntslpDsVlanIdAclErrPkts | read-only | current | Total number of Ethernet packets received from the network and discarded for the specified PVC due to VLAN Id Access Control List filtering. Valid from: EDA 2.… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.5 | ColumntslpDsEthTypeAclErrPkts | read-only | current | Total number of Ethernet packets received from the network and discarded for the specified PVC due to Ethernet type Access Control List filtering. Valid from: … |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.10 | ColumntslpDsIpAclErrPkts | read-only | current | Total number of IP packets received from the network and discarded for the specified PVC due to IP Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.15 | ColumntslpDsGatewayErrPkts | read-only | current | Total number of Ethernet packets received from the network and discarded for the specified PVC due to - gateway MAC address not resolved by IPDSLAM - Source MA… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.20 | ColumntslpDsMacErrPkts | read-only | current | Total number of packets received from the network and discarded for the specified PVC due to : - destination MAC address not present in the subscriber MAC filt… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.25 | ColumntslpDsBcastErrPkts | read-only | current | Total number of broadcast packets received from the network and discarded for the specified PVC due to : - Gateway MAC address not resolved by IPDSLAM. - Broad… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.30 | ColumntslpDsL2cpErrPkts | read-only | current | Total number of L2CP packets received by the subscriber on the specified PVC and discarded due to L2CP Tunneling not enabled for the received protocol. Valid f… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.35 | ColumntslpUsVlanIdAclErrPkts | read-only | current | Total number of Ethernet packets received from the subscriber on the specified PVC and discarded due to VLAN Id Access Control List filtering. Valid from: EDA … |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.40 | ColumntslpUsEthTypeAclErrPkts | read-only | current | Total number of Ethernet packets received from the subscriber on the specified PVC and discarded due to Ethernet type Access Control List filtering. Valid from… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.45 | ColumntslpUsIpAclErrPkts | read-only | current | Total number of IP packets received from the subscriber on the specified PVC and discarded due to IP Access Control List filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.50 | ColumntslpUsMacErrPkts | read-only | current | Total number of Ethernet packets received from the subscribers on the specified PVC and discarded due to : - source MAC not present in the subscriber MAC filte… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.55 | ColumntslpUsSrcIpErrPkts | read-only | current | Total number of IP packets received from the subscriber on the specified PVC and discarded due to source IP address in the packet not present in the subscriber… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.60 | ColumntslpUsGatewayErrPkts | read-only | current | Total number of Ethernet packets received from the subscriber on the specified PVC and discarded due to : - gateway MAC address not resolved by IPDSLAM - Desti… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.65 | ColumntslpUsBcastErrPkts | read-only | current | Total number of broadcast packets received from the subscriber on the specified PVC and discarded due to subscriber not allowed to send broadcast. Valid from: … |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.70 | ColumntslpUsL2cpErrPkts | read-only | current | Total number of L2CP packets received from the subscriber on the specified PVC and discarded due to : - L2CP Tunneling not enabled for the received protocol. -… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.75 | ColumntslpUsIcmpErrPkts | read-only | current | Total number of ICMP packets received from the subscriber on the specified PVC and discarded due to ICMP security filtering. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.80 | ColumntslpUsOversizedFrameErrPkts | read-only | current | Total number of Ethernet packets received from the subscriber on the specified PVC and discarded due to packet size exceeding peaBridgeIpDslam::maximumEthernet… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.85 | ColumntslpUsPvcPolicingErrPkts | read-only | current | Total number of Ethernet packets received from the subscriber on the specified PVC and discarded due to upstream policing. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.5.1.999 | ColumntslpErrorsClearStat | read-write | current | This parameter resets all the trafStatLogiPortErrors traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.9 | TabletrafStatLogiPortClearTable | not-accessible | current | This table contains tslpClearStat parameter which resets the upstream and downstream Logical port traffic statistics of the IPDSLAM to zero. Valid from: EDA 2.… |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.9.1 | RowtrafStatLogiPortClearEntry | not-accessible | current | An entry in the trafStatLogiPortClearTable. Valid from: EDA 2.2 SP3 |
| 1.3.6.1.4.1.193.72.300.30.1.40.6.9.1.1 | ColumntslpClearStat | read-write | current | This parameter resets all the following Logical port traffic statistics of the IPDSLAM to zero. - peaBridgeIpDslam::trafStatLogiPortMain - peaBridgeIpDslam::tr… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| EthernetTypeList | OCTET STRING LineIndex ::= INTEGER(0..2147483646) | current | A list of EthernetType entries, each two byte in network byte order (big endian). Example: EthernetTypeIp=0x800 => '0x08 0x00' |
| LineIndex | INTEGER(0..2147483646) |