PERSEUS-MIB
71 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.18 | NodelinkSwitch1000-mib | |||
| 1.3.6.1.4.1.43.18.1 | NodelinkSwitchStackGroup | |||
| 1.3.6.1.4.1.43.18.1.1 | ScalarlsStackFwdingAction | read-write | mandatory | This object specifies what action a Perseus unit takes when it receives a packet with an unknown destination address. A unit can forward the packet to the down… |
| 1.3.6.1.4.1.43.18.1.2 | ScalarlsStackFwdingMode | read-write | mandatory | This object controls whether cut-thru is enabled on the stack. Enabling cut-thru can help to minimise the delay experienced by packets before they are forwarde… |
| 1.3.6.1.4.1.43.18.2 | NodelinkSwitchConfigGroup | |||
| 1.3.6.1.4.1.43.18.2.1 | TablelsConfigPortTable | not-accessible | mandatory | Table providing configuration information about a port on a Perseus unit. |
| 1.3.6.1.4.1.43.18.2.1.1 | RowlsConfigPortEntry | not-accessible | mandatory | Configuration options for a single port. |
| 1.3.6.1.4.1.43.18.2.1.1.1 | ColumnlsConPortUnitId | read-only | mandatory | This attribute uniquely identifies a unit on a stack (or a card within a chassis) for which this table entry contains configuration information. |
| 1.3.6.1.4.1.43.18.2.1.1.2 | ColumnlsConPortId | read-only | mandatory | This parameter specifies the second part of the index into this table. Having selected a unit/card, it is now necessary to identify the port on the unit/card. |
| 1.3.6.1.4.1.43.18.2.1.1.3 | ColumnlsConPortWorkGroupId | read-write | mandatory | This attribute uniquely identifies the workgroup of which this port is a member. The attribute is used as an index in the WorkGroup table to locate this port's… |
| 1.3.6.1.4.1.43.18.2.1.1.4 | ColumnlsConPortIfIndex | read-only | mandatory | This attribute specifies the index into the ifTable, for the interface corresponding to this port. |
| 1.3.6.1.4.1.43.18.2.1.1.5 | ColumnlsConPortMode | read-write | mandatory | This attribute specifies the mode of the TP link between a port and its endstation. If the attribute is set to 'fullDuplex', frames are sent and received simul… |
| 1.3.6.1.4.1.43.18.2.1.1.6 | ColumnlsConPortIFM | read-write | mandatory | This object controls the Intelligent Flow Management for the port. It specifies what action a port takes whenever it is unable to receive a packet because its … |
| 1.3.6.1.4.1.43.18.2.1.1.7 | ColumnlsConPortDiscardOnTx | read-write | mandatory | This attribute indicates if the 'Discard-on-transmit' feature is enabled for frames originating at this port and going to any one of the other ports on a Perse… |
| 1.3.6.1.4.1.43.18.2.2 | TablelsWorkGroupTable | not-accessible | mandatory | This table provides configuration information about the workgroups on a Perseus unit. A workgroup is a collection of ports which may freely communicate with ea… |
| 1.3.6.1.4.1.43.18.2.2.1 | RowlsWorkGroupEntry | not-accessible | mandatory | Configuration information about a particular workgroup on a Perseus unit. |
| 1.3.6.1.4.1.43.18.2.2.1.1 | ColumnlsWorkGroupIndex | read-only | mandatory | This attribute uniquely identifies one of the workgroups on a unit. This attribute is also used as an index into the WorkGroup table. |
| 1.3.6.1.4.1.43.18.2.2.1.2 | ColumnlsWorkGroupName | read-write | mandatory | This attribute specifies a text string which uniquely identifies the workgroup. It may be set only if the value of lsWorkGroupRowStatus is notInService(2) or n… |
| 1.3.6.1.4.1.43.18.2.2.1.3 | ColumnlsWorkGroupDLUnitId | read-write | mandatory | This attribute specifies the identity of the unit on which this workgroup's downlink resides. It may be set only if the value of lsWorkGroupRowStatus is notInS… |
| 1.3.6.1.4.1.43.18.2.2.1.4 | ColumnlsWorkGroupDLPortId | read-write | mandatory | This attribute identifies the downlink port for this workgroup. It may be set only if the value of lsWorkGroupRowStatus is notInService(2) or notReady(3), or t… |
| 1.3.6.1.4.1.43.18.2.2.1.5 | ColumnlsWorkGroupRowStatus | read-write | mandatory | The WorkGroup table contains a row for each workgroup that exists on a unit up to a maximum of 16. Ports can be assigned to active workgroups. A new workgroup … |
| 1.3.6.1.4.1.43.18.2.2.1.6 | ColumnlsWorkGroupDBaction | read-write | mandatory | This object allows a user to carry out operations on this workgroup's address list in the forwarding database. freezeAddrs(2) makes all addresses in the workgr… |
| 1.3.6.1.4.1.43.18.3 | NodelinkSwitchMonitorGroup | |||
| 1.3.6.1.4.1.43.18.3.1 | TablelsMonitorWGTable | not-accessible | mandatory | This table provides monitoring information on a workgroup which has been setup on a Perseus hub. |
| 1.3.6.1.4.1.43.18.3.1.1 | RowlsMonitorWGTableEntry | not-accessible | mandatory | Monitoring information for a single workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.1 | ColumnlsMonWgIndex | read-only | mandatory | A stack/chassis may contain more than one workgroup. This parameter uniquely identifies the workgroup which is the target of the request. |
| 1.3.6.1.4.1.43.18.3.1.1.2 | ColumnlsMonWgTxFrames | read-only | mandatory | This parameter specifies the number of frames (including error frames) which were transmitted by ports in this workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.3 | ColumnlsMonWgTxOctets | read-only | mandatory | This parameter specifies the number of octets (including octets in error frames) which were transmitted by ports in this workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.4 | ColumnlsMonWgTxErrors | read-only | mandatory | This parameter specifies the number of error frames which were transmitted by ports in this workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.5 | ColumnlsMonWgRxCongestion | read-only | mandatory | This parameter specifies the number of frames which were dropped due to congestion (lack of buffer resource) on the receive side of ports in this workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.6 | ColumnlsMonWgTxCongestion | read-only | mandatory | This parameter specifies the number of frames which were dropped due to congestion (lack of buffer resource) on the transmit side of ports in this workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.7 | ColumnlsMonWgFilteredFrms | read-only | mandatory | The total number of frames within a workgroup that were filtered because the destination station was on the same segment (port) as the source station. |
| 1.3.6.1.4.1.43.18.3.1.1.8 | ColumnlsMonWgForwardedFrms | read-only | mandatory | The total number of frames that were forwarded successfully by ports in this workgroup to their destinations. |
| 1.3.6.1.4.1.43.18.3.1.1.9 | ColumnlsMonWgTxUnderruns | read-only | mandatory | The total number of frames within this workgroup that were transmitted with a bad CRC because the MMAC did not have enough data to continue transmission. |
| 1.3.6.1.4.1.43.18.3.1.1.10 | ColumnlsMonWgRxDribble | read-only | mandatory | The total number of frames that were received by ports in this workgroup which has dribble bits at the end of the frames |
| 1.3.6.1.4.1.43.18.3.1.1.11 | ColumnlsMonWgCutThrus | read-only | mandatory | The total number of frames that were forwarded to their destinstion in 'cut-thru' mode by ports in this workgroup. When a port is operating in 'cut-thru' mode,… |
| 1.3.6.1.4.1.43.18.3.1.1.12 | ColumnlsMonWgJamCount | read-only | mandatory | The total number of attempts made to jam frames due to insufficient resources at the receive ports in this workgroup. |
| 1.3.6.1.4.1.43.18.3.1.1.13 | ColumnlsMonWgClearCounters | read-write | mandatory | This attribute is used to clear all counters on all ports in a workgroup. |
| 1.3.6.1.4.1.43.18.3.2 | TablelsMonitorPortTable | not-accessible | mandatory | This table provides monitoring information about a port on a Perseus unit. This information is in addition to the statistical information already provided by t… |
| 1.3.6.1.4.1.43.18.3.2.1 | RowlsMonitorPortTableEntry | not-accessible | mandatory | Monitor options for a single port. |
| 1.3.6.1.4.1.43.18.3.2.1.1 | ColumnlsMonPortWgIndex | read-only | mandatory | A stack/chassis may contain more than one workgroup. This parameter uniquely identifies the workgroup which is the target of the request. |
| 1.3.6.1.4.1.43.18.3.2.1.2 | ColumnlsMonPortUnitId | read-only | mandatory | A stack/chassis may contain more than one unit/card. This parameter uniquely identifies the unit/card which is the target of a request. |
| 1.3.6.1.4.1.43.18.3.2.1.3 | ColumnlsMonPortId | read-only | mandatory | A unit/card contains many ports. This parameter uniquely identifies the port which is the target of a request. |
| 1.3.6.1.4.1.43.18.3.2.1.4 | ColumnlsMonPortReceivedFrms | read-only | mandatory | The total number of good and bad frames that were received at this port. |
| 1.3.6.1.4.1.43.18.3.2.1.5 | ColumnlsMonPortTransmittedFrms | read-only | mandatory | The total number of good and bad frames that were transmitted from this port. |
| 1.3.6.1.4.1.43.18.3.2.1.6 | ColumnlsMonPortFilteredFrms | read-only | mandatory | The total number of frames that were filtered because the destination station was on the same segment (port) as the source station. |
| 1.3.6.1.4.1.43.18.3.2.1.7 | ColumnlsMonPortForwardedFrms | read-only | mandatory | The total number of frames which were received by this port and forwarded to their destinations. |
| 1.3.6.1.4.1.43.18.3.2.1.8 | ColumnlsMonPortFragmentFrms | read-only | mandatory | The total number of frames less than 64 octets and with a bad CRC that were received at/transmitted from this port. |
| 1.3.6.1.4.1.43.18.3.2.1.9 | ColumnlsMonPortRxCongestion | read-only | mandatory | This parameter specifies the number of frames which were dropped due to congestion (lack of buffer resource) on the receive side of this port. |
| 1.3.6.1.4.1.43.18.3.2.1.10 | ColumnlsMonPortTxCongestion | read-only | mandatory | This parameter specifies the number of frames which were dropped due to congestion (lack of buffer resource) on the transmit side of this port. |
| 1.3.6.1.4.1.43.18.3.2.1.11 | ColumnlsMonPortTxUnderruns | read-only | mandatory | The total number of frames that were transmitted with an bad CRC because the MMAC did not have enough data to continue transmission. |
| 1.3.6.1.4.1.43.18.3.2.1.12 | ColumnlsMonPortRxDribble | read-only | mandatory | The number of frames that were received on this port with dribble bits at the end of the frame. |
| 1.3.6.1.4.1.43.18.3.2.1.13 | ColumnlsMonPortCutThrus | read-only | mandatory | The total number of frames that were forwarded to their destination in 'cut-through' mode. When a port is operating in 'cut-through' mode, it starts forwarding… |
| 1.3.6.1.4.1.43.18.3.2.1.14 | ColumnlsMonPortRxJamCount | read-only | mandatory | The total number of attempts made to jam packets due to insufficient resources at the receive port. |
| 1.3.6.1.4.1.43.18.3.2.1.15 | ColumnlsMonPortPercentFwd | read-only | mandatory | This is a high level 'Smart' MIB object. This object provides a running average of the proportion of the received frames that are forwarded. This value is calc… |
| 1.3.6.1.4.1.43.18.3.2.1.16 | ColumnlsMonPortBcastBndwth | read-only | mandatory | This is a high level 'Smart' MIB object. This object provides a running average of the Broadcast frame bandwidth in use. This value is calculated locally on th… |
| 1.3.6.1.4.1.43.18.3.2.1.17 | ColumnlsMonPortClearCounters | read-write | mandatory | This attribute is used to clear all counters on a port. |
| 1.3.6.1.4.1.43.18.4 | NodelinkSwitchDatabaseGroup | |||
| 1.3.6.1.4.1.43.18.4.1 | ScalarlsDatabaseSize | read-only | mandatory | This parameter indicates the number of permanent and non-permanent entries currently held in the database on a linkSwitch1000 hub. |
| 1.3.6.1.4.1.43.18.4.2 | ScalarlsPermDatabaseSize | read-only | mandatory | This parameter indicates the number of permanent addresses currently held in the database on a linkSwitch1000. |
| 1.3.6.1.4.1.43.18.4.3 | TablelsDbPortTable | not-accessible | mandatory | Port View Table |
| 1.3.6.1.4.1.43.18.4.3.1 | RowlsDbPortEntry | not-accessible | mandatory | Port View Table entry |
| 1.3.6.1.4.1.43.18.4.3.1.1 | ColumnlsDbPortUnitId | read-only | mandatory | A linkSwitch stack may contain up to 4 units. This parameter uniquely identifies the unit on which the address was learnt. |
| 1.3.6.1.4.1.43.18.4.3.1.2 | ColumnlsDbPortPortId | read-only | mandatory | A linkSwitch1000 unit can contain up to 26 ports. This parameter uniquely the port on which the address was learnt. |
| 1.3.6.1.4.1.43.18.4.3.1.3 | ColumnlsDbPortIndex | read-only | mandatory | Multiple addresses can be learnt on a single port. This parameter uniquely identifies one address on a port. |
| 1.3.6.1.4.1.43.18.4.3.1.4 | ColumnlsDbPortAddress | read-write | mandatory | The physical address of the station which has been learnt on a port on a linkSwitch1000 stack. |
| 1.3.6.1.4.1.43.18.4.3.1.5 | ColumnlsDbPortAddrStatus | read-write | mandatory | This attribute indicates if the address will age out of the database on a linkSwitch1000 unit when it is not the subject of lookup requests (nonPermanent) OR i… |
| 1.3.6.1.4.1.43.18.5 | NodelinkSwitchSmartGroup | |||
| 1.3.6.1.4.1.43.18.5.1 | ScalarlsSmartPercentFwd | read-only | mandatory | This is a smart MIB object which is used internally by the agent to provide a running average of the percentage of incoming frames which are forwarded. It shou… |
| 1.3.6.1.4.1.43.18.5.2 | ScalarlsSmartBcastBndwdth | read-only | mandatory | This is a smart MIB object which is used internally by the agent to provide a running average of the broadcast bandwidth in use. It should not be accessed by a… |