PHIHONG-PoE-MIB
52 objects
No module-level DESCRIPTION found.
Imported Objects
| SNMPv2-SMI | enterprises Gauge32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.24852 | Nodephihong | |||
| 1.3.6.1.4.1.24852.2 | NodepoeProduct | |||
| 1.3.6.1.4.1.24852.2.1 | ScalarpoeProductsPart | read-only | current | the POE controller Part. |
| 1.3.6.1.4.1.24852.2.2 | NodepoeSystem | |||
| 1.3.6.1.4.1.24852.2.2.1 | ScalarpoeSystemActionHubReset | write-only | current | Reset the POE controller. |
| 1.3.6.1.4.1.24852.2.2.2 | ScalarpoeSystemActionHubRestoreFactoryDefault | write-only | current | Restore Factory Default to flash. resetpassword means when users forget the password,they can use this entry, and all of the snmp module parameters will be set… |
| 1.3.6.1.4.1.24852.2.2.3 | ScalarpoeSystemActionHubSaveConfiguration | write-only | current | Save the POE parameters to flash |
| 1.3.6.1.4.1.24852.2.2.4 | ScalarpoeSystemAllPortPowerEnable | write-only | current | Enables power supply in all port. Setting this object at a value enable(2) enables power and detection mechanism for all port. Setting this object at a value d… |
| 1.3.6.1.4.1.24852.2.2.6 | ScalarpoeSystemHWVersion | read-only | current | System hardware version for the Main board |
| 1.3.6.1.4.1.24852.2.2.7 | ScalarpoeSystemNumberOfChannel | read-only | current | Number of ports in the system |
| 1.3.6.1.4.1.24852.2.2.8 | ScalarpoeSystemProductPartNumber | read-only | current | System Part Number for PowerHub |
| 1.3.6.1.4.1.24852.2.2.10 | ScalarpoeSystemFirmwareVersion | read-only | current | System firmware version for the POE |
| 1.3.6.1.4.1.24852.2.2.11 | ScalarpoeSystemDescription | read-write | current | System Description 10 characters |
| 1.3.6.1.4.1.24852.2.2.12 | ScalarpoeSystemConsumptionPower | read-only | current | Measured usage power expressed in Watts. |
| 1.3.6.1.4.1.24852.2.2.13 | ScalarpoeSystemControlACPower | read-write | current | describes the maximum available power in Watts to be supplied by the AC backup source to this device. |
| 1.3.6.1.4.1.24852.2.2.14 | ScalarpoeSystemControlDCPower | read-write | current | describes the maximum available power in Watts to be supplied by the DC backup source to this device. |
| 1.3.6.1.4.1.24852.2.2.15 | ScalarpoeSystemControlBothPower | read-write | current | describes the maximum available power in Watts to be supplied by Both AC and DC backup source to this device. |
| 1.3.6.1.4.1.24852.2.2.16 | ScalarpoeSystemParameters | read-write | current | 1st char:Knokoff enable,2nd char:AC Disconnect enable,3th char:Disable Power Management |
| 1.3.6.1.4.1.24852.2.2.17 | ScalarpoeSystemSnmpVersion | read-only | current | The software version for the SNMP device |
| 1.3.6.1.4.1.24852.2.2.18 | ScalarpoeSystemPerPortPowerEnable | read-write | current | Enables power supply in all port. Setting this object at a value enable(2) enables power and detection mechanism for all port. Setting this object at a value d… |
| 1.3.6.1.4.1.24852.2.2.19 | ScalarpoeSystemStatus | read-only | current | The status of the POE. |
| 1.3.6.1.4.1.24852.2.3 | TablepoePortTable | not-accessible | current | |
| 1.3.6.1.4.1.24852.2.3.1 | RowpoePortEntry | not-accessible | current | port entry containing data regarding a particular port |
| 1.3.6.1.4.1.24852.2.3.1.1 | ColumnpoePortIndex | read-only | current | A unique value for each port. |
| 1.3.6.1.4.1.24852.2.3.1.2 | ColumnpoePortPowerEnable | read-write | current | Enables power supply on this port. Setting this object at a value enable(2) enables power and detection mechanism for this port. Setting this object at a value… |
| 1.3.6.1.4.1.24852.2.3.1.3 | ColumnpoePortControlMaxPower | read-write | current | This command specifies the max power in [mWatts] to that port. IF you set this value it will take out this port from the auto mode. The value MUST be more then… |
| 1.3.6.1.4.1.24852.2.3.1.6 | ColumnpoePortDescription | read-write | current | Port Description 10 characters |
| 1.3.6.1.4.1.24852.2.3.1.7 | ColumnpoePortDetectionStatus | read-only | current | Port Detection, show the detection status of each port |
| 1.3.6.1.4.1.24852.2.3.1.8 | ColumnpoePortPowerClassifications | read-only | current | Port Power Classifications, show the classification of each port |
| 1.3.6.1.4.1.24852.2.3.1.9 | ColumnpoePortPowerDetectionControl | read-write | current | Port Power Detection Control, enable or disable the Power Limit for Management |
| 1.3.6.1.4.1.24852.2.3.1.10 | ColumnpoePortPowerPriority | read-write | current | Port Power Priority, show the priority of each port |
| 1.3.6.1.4.1.24852.2.3.1.11 | ColumnpoePortPower | read-only | current | Port Actual Power (in mWattes). |
| 1.3.6.1.4.1.24852.2.3.1.12 | ColumnpoePortVoltage | read-only | current | Port Voltage (in dVoltage). |
| 1.3.6.1.4.1.24852.2.3.1.13 | ColumnpoePortCurrent | read-only | current | Port Current (in mAmps). |
| 1.3.6.1.4.1.24852.2.3.1.14 | ColumnpoePortResistance | read-only | current | Port Resistance (in ohms). |
| 1.3.6.1.4.1.24852.2.3.1.15 | ColumnpoePortFlags | read-only | current | 1st char:classification(0-3),2nd char:Port bypass detection enable,3th char:Port bypass classifiation enable,4th cahr:Port bypass powerup enable,5th char:Port … |
| 1.3.6.1.4.1.24852.2.3.1.16 | ColumnpoePortBypassFlags | read-write | current | 1st char:Port bypass detection enable,2nd char:Port bypass classifiation enable,3th cahr:Port bypass powerup enable,4th char:Port bypass sampling enable. |
| 1.3.6.1.4.1.24852.2.3.1.17 | ColumnpoePortUseClassificationforPowerLimit | read-write | current | Use Port classification for power limit , enable or disable the Port classification for power limit. |
| 1.3.6.1.4.1.24852.2.3.1.18 | ColumnpoePortLegacyDetection | read-write | current | Use Port legacy detection , enable or disable the Port legacy detection. |
| 1.3.6.1.4.1.24852.2.4 | TablepoeTrapsControlTable | not-accessible | current | A table of objects that display and control the Traps on a PSM device. |
| 1.3.6.1.4.1.24852.2.4.1 | RowpoeTrapsControlEntry | not-accessible | current | A set of objects that control the Trap events. |
| 1.3.6.1.4.1.24852.2.4.1.1 | ColumnpoeTrapsControlGroupIndex | not-accessible | current | This variable uniquely identifies the group. |
| 1.3.6.1.4.1.24852.2.4.1.2 | ColumnpoeTrapsControlEnable | read-write | current | Enable Traps from Agent |
| 1.3.6.1.4.1.24852.2.5 | NodepoeTraps | |||
| 1.3.6.1.4.1.24852.2.5.1 | NotificationpoePortHWFailTrap | current | This trap indicate UV0v failure /UV0v Spike failure /Device A2d failure. | |
| 1.3.6.1.4.1.24852.2.5.2 | NotificationpoePortPeakOverCurrentTrap | current | This trap indicate peak over current failure. | |
| 1.3.6.1.4.1.24852.2.5.3 | NotificationpoePortOverloadTrap | current | This trap indicate overload failure. If you put at least 400mA on the output, you will see if your traps work | |
| 1.3.6.1.4.1.24852.2.5.4 | NotificationpoePortDiscoveryFailTrap | current | This trap indicate Discovery failure/ Discovery VA2 failure/Discovery RA2 failure/Sample Discovery A2d Failure. | |
| 1.3.6.1.4.1.24852.2.5.5 | NotificationpoePortClassificationFailTrap | current | This trap indicate Class Violation failure/ Classification A2d failure. | |
| 1.3.6.1.4.1.24852.2.5.6 | NotificationpoePortDisconnectTrap | current | This trap indicate port is disconnected. | |
| 1.3.6.1.4.1.24852.2.5.7 | NotificationpoePortVoltageFailTrap | current | This trap indicate if PSM Port is no voltage failure. | |
| 1.3.6.1.4.1.24852.2.5.8 | NotificationpoeSystemOverheatTrap | current | This trap indicate if PSM is overheat. |