PW-DRAFT05-MIB
128 objects
This MIB module contains managed object definitions for Pseudo Wire operation as in: Bryant., et al, 'PWE3 architecture', Martini, L., et al, 'Pseudowire Setup and Maintenance using LDP', and Townsley, M., et al, 'Layer Two Tunneling Protocol (Version 3)'. Pseudo Wire (PW) Management June 2004 Information Base This MIB module enables the use of any underlying packet switched network (PSN). MIB nodules that will support PW operations over specific PSN types are defined in separate memos. The indexes for this MIB module are also used to index the PSN-specific tables and the PW-specific tables. The PW Type dictates which PW-specific MIB module to use. Copyright (C) The Internet Society (date). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices.
Imported Objects
| HC-PerfHist-TC-MIB | HCPerfCurrentCount HCPerfIntervalCount HCPerfTimeElapsed HCPerfValidIntervals |
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | Management June 2004 Information Base |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount |
| PW-TC-DRAFT05-MIB | PwGroupID PwOperStatus pwStdMIB PwVcAttachmentIdentifierType PwVcCapabilities PwVcCwStatus PwVcFragSize PwVcFragStatus PwVcIDType PwVcIndexType PwVcStatus PwVcType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10 | IdentitypwVcMIB | This MIB module contains managed object definitions for Pseudo Wire operation as in: Bryant., et al, 'PWE3 architecture', Martini, L., et al, 'Pseudowire Setup… | ||
| 1.3.6.1.2.1.10.0 | NodepwVcNotifications | |||
| 1.3.6.1.2.1.10.0.1 | NotificationpwVcDown | current | This notification is generated when the pwVcOperStatus object for one or more contiguous entries in pwVcTable are about to enter the down(2) state from some ot… | |
| 1.3.6.1.2.1.10.0.2 | NotificationpwVcUp | current | This notification is generated when the pwVcOperStatus object for one or more contiguous entries in pwVcTable are about to enter the up(1) Pseudo Wire (PW) Man… | |
| 1.3.6.1.2.1.10.0.3 | NotificationpwVcDeleted | current | This notification is generated when the PW has been deleted, i.e. when the pwVcRowStatus has been set to destroy(6), the PW has been deleted by a non-MIB appli… | |
| 1.3.6.1.2.1.10.1 | NodepwVcObjects | |||
| 1.3.6.1.2.1.10.1.1 | ScalarpwVcIndexNext | read-only | current | This object contains an appropriate value to be used for pwVcIndex when creating entries in the Pseudo Wire (PW) Management June 2004 Information Base pwVcTabl… |
| 1.3.6.1.2.1.10.1.2 | TablepwVcTable | not-accessible | current | This table specifies information for configuring and status monitoring which are common to all service types and PSN types. |
| 1.3.6.1.2.1.10.1.2.1 | RowpwVcEntry | not-accessible | current | A row in this table represents a pseudo wire (PW) virtual connection (VC) across a packet network. It is indexed by pwVcIndex, which uniquely identifying a sin… |
| 1.3.6.1.2.1.10.1.2.1.1 | ColumnpwVcIndex | not-accessible | current | Index for the conceptual row identifying a PW within this PW Emulation table. |
| 1.3.6.1.2.1.10.1.2.1.2 | ColumnpwVcType | read-create | current | This value indicate the service to be carried over this PW. |
| 1.3.6.1.2.1.10.1.2.1.3 | ColumnpwVcOwner | read-create | current | Set by the operator to indicate the protocol responsible for establishing this PW. Value 'manual' is used in all cases where no maintenance protocol (PW signal… |
| 1.3.6.1.2.1.10.1.2.1.4 | ColumnpwVcPsnType | read-create | current | Set by the operator to indicate the PSN type on which this PW will be carried. Based on this object, the relevant PSN table entries are created in the in the P… |
| 1.3.6.1.2.1.10.1.2.1.5 | ColumnpwVcSetUpPriority | read-create | current | This object define the relative set-up priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treat… |
| 1.3.6.1.2.1.10.1.2.1.6 | ColumnpwVcHoldingPriority | read-create | current | This object define the relative holding priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are trea… |
| 1.3.6.1.2.1.10.1.2.1.8 | ColumnpwVcPeerAddrType | read-create | current | Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown. |
| 1.3.6.1.2.1.10.1.2.1.9 | ColumnpwVcPeerAddr | read-create | current | This object contain the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applic… |
| 1.3.6.1.2.1.10.1.2.1.10 | ColumnpwVcAttachedPwIndex | read-create | current | If the PW is attached to another PW instead of a local native service, this item indicates the pwVcIndex of the attached PW, and the PW specific entry in the s… |
| 1.3.6.1.2.1.10.1.2.1.11 | ColumnpwVcIfIndex | read-create | current | If the PW is represented in the ifTable as an ifIndex, this item holds the ifIndex of the PW in the ifTable, otherwise it MUST be set to zero. |
| 1.3.6.1.2.1.10.1.2.1.12 | ColumnpwVcID | read-create | current | Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Applicable if pwVcOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be… |
| 1.3.6.1.2.1.10.1.2.1.13 | ColumnpwVcLocalGroupID | read-create | current | Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. Applicable if pwVcOwner equal 'pwIdFecSignaling' or 'l2tpCo… |
| 1.3.6.1.2.1.10.1.2.1.14 | ColumnpwVcGroupAttachmentID | read-create | current | This object is an octet string representing the attachment group identifier (AGI) this PW belongs too, which typically identifies the VPN ID. Applicable if pwV… |
| 1.3.6.1.2.1.10.1.2.1.15 | ColumnpwVcLocalAttachmentID | read-create | current | This object is an octet string representing the local forwarder attachment individual identifier (AII) to be used by this PW. It is used as the SAII for outgoi… |
| 1.3.6.1.2.1.10.1.2.1.16 | ColumnpwVcPeerAttachmentID | read-create | current | This object is an octet string representing the peer forwarder attachment individual identifier (AII) to be used by this PW. It is used as the TAII for outgoin… |
| 1.3.6.1.2.1.10.1.2.1.17 | ColumnpwVcCwPreference | read-create | current | Defines if the control word will be sent with each packet by the local node. Some PW types mandate the use of control word, and is such cases the value configu… |
| 1.3.6.1.2.1.10.1.2.1.18 | ColumnpwVcLocalIfMtu | read-create | current | If not equal zero, the optional IfMtu object in the signaling protocol will be sent with this value, representing the locally supported MTU size over the inter… |
| 1.3.6.1.2.1.10.1.2.1.19 | ColumnpwVcLocalIfString | read-create | current | Each PW is associated to an interface (or a virtual interface) in the ifTable of the node as part of the service configuration. This object defines if the main… |
| 1.3.6.1.2.1.10.1.2.1.20 | ColumnpwVcLocalCapabAdvert | read-create | current | Indicates the capabilities to be advertised by this node to the peer. |
| 1.3.6.1.2.1.10.1.2.1.21 | ColumnpwVcRemoteGroupID | read-only | current | Obtained from the Group ID field as received via the signaling protocol used for VC setup, zero if not used. Value of 0xFFFF shall be used if the object is yet… |
| 1.3.6.1.2.1.10.1.2.1.22 | ColumnpwVcCwStatus | read-only | current | If signaling is used for PW establishment, this object indicates the status of the control word negotiation, Pseudo Wire (PW) Management June 2004 Information … |
| 1.3.6.1.2.1.10.1.2.1.23 | ColumnpwVcRemoteIfMtu | read-only | current | The remote interface MTU as (optionally) received from the remote node via the maintenance protocol. Should be zero if this parameter is not available or not u… |
| 1.3.6.1.2.1.10.1.2.1.24 | ColumnpwVcRemoteIfString | read-only | current | Indicates the interface description string as received by the maintenance protocol, MUST be NULL string if not applicable or not known yet. |
| 1.3.6.1.2.1.10.1.2.1.25 | ColumnpwVcRemoteCapabilities | read-only | current | Indicates the capabilities as advertised by the peer. |
| 1.3.6.1.2.1.10.1.2.1.26 | ColumnpwVcFragmentCfgSize | read-create | current | If set to value other than zero, indicates that fragmentation is desired for this PW. |
| 1.3.6.1.2.1.10.1.2.1.27 | ColumnpwVcRmtFragCapability | read-only | current | The status of the fragmentation based on the local configuration and the peer capabilities as advertised by the peer if control protocol is used. |
| 1.3.6.1.2.1.10.1.2.1.28 | ColumnpwVcFcsRetentioncfg | read-create | current | The local configuration of FCS retention for this PW. FCS retention can be configured for PW types HDLC, PPP and Ethernet only. If the agent does not support F… |
| 1.3.6.1.2.1.10.1.2.1.29 | ColumnpwVcFcsRetentionStatus | read-only | current | The status of the FCS retention negotiation process based on local configuration and the remote advertisement. remoteIndicationUnknown - set if a FEC has not b… |
| 1.3.6.1.2.1.10.1.2.1.30 | ColumnpwVcOutboundVcLabel | read-create | current | The PW label used in the outbound direction (i.e. toward the PSN). It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPL… |
| 1.3.6.1.2.1.10.1.2.1.31 | ColumnpwVcInboundVcLabel | read-create | current | The PW label used in the inbound direction (i.e. packets received from the PSN. It may be set up manually if owner is 'manual' or automatically otherwise. Exam… |
| 1.3.6.1.2.1.10.1.2.1.32 | ColumnpwVcName | read-create | current | The canonical name assigned to the PW. |
| 1.3.6.1.2.1.10.1.2.1.33 | ColumnpwVcDescr | read-create | current | A textual string containing information about the PW. If there is no description this object contains a zero length string. |
| 1.3.6.1.2.1.10.1.2.1.34 | ColumnpwVcCreateTime | read-only | current | System time when this PW was created. |
| 1.3.6.1.2.1.10.1.2.1.35 | ColumnpwVcUpTime | read-only | current | Specifies the total time this PW operStatus has been Up(1). |
| 1.3.6.1.2.1.10.1.2.1.36 | ColumnpwVcLastChange | read-only | current | The value of sysUpTime at the time the PW entered its current operational state. If the current state was entered prior to the last re-initialization of the lo… |
| 1.3.6.1.2.1.10.1.2.1.37 | ColumnpwVcAdminStatus | read-create | current | The desired operational status of this PW. |
| 1.3.6.1.2.1.10.1.2.1.38 | ColumnpwVcOperStatus | read-only | current | This object indicates the operational status of the PW, it does not reflect however the status of the CE bound interface. It is set to down only if pwNotForwar… |
| 1.3.6.1.2.1.10.1.2.1.39 | ColumnpwVcLocalStatus | read-only | current | Indicates the status of the PW in the local node. The various indications in this object should be available independent of the ability of the local node to ad… |
| 1.3.6.1.2.1.10.1.2.1.40 | ColumnpwVcRemoteStatusCapable | read-only | current | Indicates the remote node capability to advertise the Pseudo Wire (PW) Management June 2004 Information Base PW status notification. notAppicable should be rep… |
| 1.3.6.1.2.1.10.1.2.1.41 | ColumnpwVcRemoteStatus | read-only | current | Indicates the status of the PW as was advertised by the remote. If the remote is not capable of advertising the status object, or the local node is not able to… |
| 1.3.6.1.2.1.10.1.2.1.42 | ColumnpwVcTimeElapsed | read-only | current | The number of seconds, including partial seconds, that have elapsed since the beginning of the current interval measurement period. |
| 1.3.6.1.2.1.10.1.2.1.43 | ColumnpwVcValidIntervals | read-only | current | The number of previous 15-minute intervals for which data was collected. |
| 1.3.6.1.2.1.10.1.2.1.44 | ColumnpwVcRowStatus | read-create | current | |
| 1.3.6.1.2.1.10.1.2.1.45 | ColumnpwVcStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.2.1.10.1.3 | TablepwVcPerfCurrentTable | not-accessible | current | This table provides per-PW performance information for the current interval. |
| 1.3.6.1.2.1.10.1.3.1 | RowpwVcPerfCurrentEntry | not-accessible | current | An entry in this table is created by the agent for every PW. |
| 1.3.6.1.2.1.10.1.3.1.1 | ColumnpwVcPerfCurrentInHCPackets | read-only | current | High capacity counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwVcPerfCurrentI… |
| 1.3.6.1.2.1.10.1.3.1.2 | ColumnpwVcPerfCurrentInHCBytes | read-only | current | High capacity counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwVcPerfCurrentInB… |
| 1.3.6.1.2.1.10.1.3.1.3 | ColumnpwVcPerfCurrentOutHCPackets | read-only | current | High capacity counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwVcPerfCurrentOu… |
| 1.3.6.1.2.1.10.1.3.1.4 | ColumnpwVcPerfCurrentOutHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwVcPerfCurrentOutB… |
| 1.3.6.1.2.1.10.1.3.1.5 | ColumnpwVcPerfCurrentInPackets | read-only | current | The counter for number of packets received by the PW (from Pseudo Wire (PW) Management June 2004 Information Base the PSN) in the current 15-minute interval. T… |
| 1.3.6.1.2.1.10.1.3.1.6 | ColumnpwVcPerfCurrentInBytes | read-only | current | The counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwVcP… |
| 1.3.6.1.2.1.10.1.3.1.7 | ColumnpwVcPerfCurrentOutPackets | read-only | current | The counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwVc… |
| 1.3.6.1.2.1.10.1.3.1.8 | ColumnpwVcPerfCurrentOutBytes | read-only | current | The counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwVcPe… |
| 1.3.6.1.2.1.10.1.4 | TablepwVcPerfIntervalTable | not-accessible | current | This table provides per-PW performance information for each interval. |
| 1.3.6.1.2.1.10.1.4.1 | RowpwVcPerfIntervalEntry | not-accessible | current | An entry in this table is created agent for every PW. |
| 1.3.6.1.2.1.10.1.4.1.1 | ColumnpwVcPerfIntervalNumber | not-accessible | current | A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently com… |
| 1.3.6.1.2.1.10.1.4.1.2 | ColumnpwVcPerfIntervalValidData | read-only | current | |
| 1.3.6.1.2.1.10.1.4.1.3 | ColumnpwVcPerfIntervalTimeElapsed | read-only | current | The duration of this interval in seconds. |
| 1.3.6.1.2.1.10.1.4.1.4 | ColumnpwVcPerfIntervalInHCPackets | read-only | current | High capacity counter for number of packets received by the PW (from the PSN) during the interval. This is the 64 bit version of pwVcPerfIntervalInPackets, if … |
| 1.3.6.1.2.1.10.1.4.1.5 | ColumnpwVcPerfIntervalInHCBytes | read-only | current | High capacity counter for number of bytes received by the PW (from the PSN) during the interval. This is the 64 bit version of pwVcPerfIntervalInBytes, if pwVc… |
| 1.3.6.1.2.1.10.1.4.1.6 | ColumnpwVcPerfIntervalOutHCPackets | read-only | current | High capacity counter for number of packets forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwVcPerfIntervalOutPackets, if … |
| 1.3.6.1.2.1.10.1.4.1.7 | ColumnpwVcPerfIntervalOutHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwVcPerfIntervalOutBytes, if pwVc… |
| 1.3.6.1.2.1.10.1.4.1.8 | ColumnpwVcPerfIntervalInPackets | read-only | current | This value represents the number of packets received by this PW during the interval. It MUST be equal to the least significant 32 bits of pwVcPerfIntervalInHCP… |
| 1.3.6.1.2.1.10.1.4.1.9 | ColumnpwVcPerfIntervalInBytes | read-only | current | This value represents the number of bytes received by this PW during the interval. It MUST be equal to the least significant 32 bits of if pwVcPerfIntervalInHC… |
| 1.3.6.1.2.1.10.1.4.1.10 | ColumnpwVcPerfIntervalOutPackets | read-only | current | This value represents the number of packets sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwVcPerfIntervalOutHCPack… |
| 1.3.6.1.2.1.10.1.4.1.11 | ColumnpwVcPerfIntervalOutBytes | read-only | current | This value represents the number of bytes sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwVcPerfIntervalOutHCBytes … |
| 1.3.6.1.2.1.10.1.5 | TablepwVcPerfTotalTable | not-accessible | current | This table provides per-PW Performance information from PW start time or management application reset. |
| 1.3.6.1.2.1.10.1.5.1 | RowpwVcPerfTotalEntry | not-accessible | current | An entry in this table is created by the agent for every PW. pwVcPerfTotalDiscontinuityTime indicates the time of the last discontinuity in any of these object… |
| 1.3.6.1.2.1.10.1.5.1.1 | ColumnpwVcPerfTotalInHCPackets | read-only | current | High capacity counter for the total number of packets received by the PW (from the PSN). This is the 64 bit version of pwVcPerfTotalInPackets, if pwVcPerfTotal… |
| 1.3.6.1.2.1.10.1.5.1.2 | ColumnpwVcPerfTotalInHCBytes | read-only | current | High capacity counter for the total number of bytes received by the PW (from the PSN). This is the 64 bit version of pwVcPerfTotalInBytes, if pwVcPerfTotalInHC… |
| 1.3.6.1.2.1.10.1.5.1.3 | ColumnpwVcPerfTotalOutHCPackets | read-only | current | High capacity counter for the total number of packets forwarded by the PW (to the PSN). This is the 64 bit version of pwVcPerfTotalOutPackets, if pwVcPerfTotal… |
| 1.3.6.1.2.1.10.1.5.1.4 | ColumnpwVcPerfTotalOutHCBytes | read-only | current | High capacity counter for the total number of bytes forwarded by the PW (to the PSN). This is the 64 bit version of pwVcPerfTotalOutBytes, if pwVcPerfTotalOutH… |
| 1.3.6.1.2.1.10.1.5.1.5 | ColumnpwVcPerfTotalInPackets | read-only | current | This value represents the total number of packets received Pseudo Wire (PW) Management June 2004 Information Base by this PW. It MUST be equal to the least sig… |
| 1.3.6.1.2.1.10.1.5.1.6 | ColumnpwVcPerfTotalInBytes | read-only | current | This value represents the total number of bytes received by this PW. It MUST be equal to the least significant 32 bits of if pwVcPerfTotalInHCBytes is supporte… |
| 1.3.6.1.2.1.10.1.5.1.7 | ColumnpwVcPerfTotalOutPackets | read-only | current | This value represents the total number of packets sent by this PW. It MUST be equal to the least significant 32 bits of pwVcPerfTotalOutHCPackets if pwVcPerfTo… |
| 1.3.6.1.2.1.10.1.5.1.8 | ColumnpwVcPerfTotalOutBytes | read-only | current | This value represents the total number of bytes sent by this PW. It MUST be equal to the least significant 32 bits of pwVcPerfTotalOutHCBytes if pwVcPerfTotalO… |
| 1.3.6.1.2.1.10.1.5.1.9 | ColumnpwVcPerfTotalDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at Pseudo Wire (PW) Management June 2004 Information Base which any one or more of this row Counter32 or Cou… |
| 1.3.6.1.2.1.10.1.6 | ScalarpwVcPerfTotalErrorPackets | read-only | current | Counter for number of error at the PW processing level, for example packets received with unknown PW label. |
| 1.3.6.1.2.1.10.1.7 | TablepwVcIndexMappingTable | not-accessible | current | This table enables the reverse mapping the unique PWid parameters <peer IP, PW type and PW ID> and the pwVcIndex. The table is not applicable for PW created ma… |
| 1.3.6.1.2.1.10.1.7.1 | RowpwVcIndexMappingEntry | not-accessible | current | An entry in this table MUST be created by the agent for every PW created by the pwVcTable for which pwVcOwner equals �pwIdFecSignaling�. |
| 1.3.6.1.2.1.10.1.7.1.1 | ColumnpwVcIndexMappingVcType | not-accessible | current | The PW type (indicates the service) of this PW. |
| 1.3.6.1.2.1.10.1.7.1.2 | ColumnpwVcIndexMappingVcID | not-accessible | current | The PW ID of this PW. Zero if the PW is configured manually. |
| 1.3.6.1.2.1.10.1.7.1.3 | ColumnpwVcIndexMappingPeerAddrType | not-accessible | current | IP address type of the peer node. |
| 1.3.6.1.2.1.10.1.7.1.4 | ColumnpwVcIndexMappingPeerAddr | not-accessible | current | IP address type of the peer node. |
| 1.3.6.1.2.1.10.1.7.1.5 | ColumnpwVcIndexMappingVcIndex | read-only | current | The value that represents the PW in the pwVcTable. |
| 1.3.6.1.2.1.10.1.8 | TablepwVcPeerMappingTable | not-accessible | current | This table provides reverse mapping of the existing PW based on PW type and PW ID ordering. This table is typically useful for EMS ordered query of existing PW… |
| 1.3.6.1.2.1.10.1.8.1 | RowpwVcPeerMappingEntry | not-accessible | current | An entry in this table is created by the agent for every PW configured in pwVcTable. |
| 1.3.6.1.2.1.10.1.8.1.1 | ColumnpwVcPeerMappingPeerAddrType | not-accessible | current | IP address type of the peer node. |
| 1.3.6.1.2.1.10.1.8.1.2 | ColumnpwVcPeerMappingPeerAddr | not-accessible | current | IP address type of the peer node. |
| 1.3.6.1.2.1.10.1.8.1.3 | ColumnpwVcPeerMappingVcType | not-accessible | current | |
| 1.3.6.1.2.1.10.1.8.1.4 | ColumnpwVcPeerMappingVcID | not-accessible | current | The PW ID of this PW. Zero if the PW is configured manually. |
| 1.3.6.1.2.1.10.1.8.1.5 | ColumnpwVcPeerMappingVcIndex | read-only | current | The value that represents the PW in the pwVcTable. |
| 1.3.6.1.2.1.10.1.9 | ScalarpwVcUpDownNotifEnable | read-write | current | If this object is set to true(1), then it enables the emission of pwVcUp and pwVcDown notifications; otherwise these notifications are not emitted. |
| 1.3.6.1.2.1.10.1.10 | ScalarpwVcDeletedNotifEnable | read-write | current | If this object is set to true(1), then it enables the emission of pwVcDeleted notification; otherwise this notification is not emitted. |
| 1.3.6.1.2.1.10.1.11 | ScalarpwVcNotifRate | read-write | current | This object defines the maximum number of PW notifications that can be emitted from the device per second. |
| 1.3.6.1.2.1.10.2 | NodepwVcConformance | |||
| 1.3.6.1.2.1.10.2.1 | NodepwVcGroups | |||
| 1.3.6.1.2.1.10.2.1.1 | GrouppwVcBasicGroup | current | Collection of objects that are required in all implementations that support the PW MIB module. | |
| 1.3.6.1.2.1.10.2.1.2 | GrouppwVcPwIdGroup | current | Collection of objects required for PW ID configuration and signaling. | |
| 1.3.6.1.2.1.10.2.1.3 | GrouppwVcGeneralizedFecGroup | current | Collection of objects required for generalized FEC configuration and signaling. | |
| 1.3.6.1.2.1.10.2.1.4 | GrouppwVcFcsGroup | current | ||
| 1.3.6.1.2.1.10.2.1.5 | GrouppwVcFragGroup | current | Collection of objects required for fragmentation configuration and signaling. | |
| 1.3.6.1.2.1.10.2.1.6 | GrouppwVcPwStatusGroup | current | Collection of objects required for PW status configuration and signaling. | |
| 1.3.6.1.2.1.10.2.1.7 | GrouppwVcGetNextGroup | current | Collection of objects for getting the next available index. | |
| 1.3.6.1.2.1.10.2.1.8 | GrouppwVcPriorityGroup | current | Collection of objects for controlling the PW setup and holding priority. | |
| 1.3.6.1.2.1.10.2.1.9 | GrouppwVcAttachmentGroup | current | Collection of objects for PW configuration and signaling. | |
| 1.3.6.1.2.1.10.2.1.10 | GrouppwVcPerformanceGeneralGroup | current | Collection of general objects needed for managing the total running performance parameters. | |
| 1.3.6.1.2.1.10.2.1.11 | GrouppwVcPeformanceTotalGroup | current | Collection of 32 bits objects needed for PW running total performance collection. | |
| 1.3.6.1.2.1.10.2.1.12 | GrouppwVcHCPeformanceTotalGroup | current | Collection of HC objects needed for PW running total performance collection. | |
| 1.3.6.1.2.1.10.2.1.13 | GrouppwVcPerformanceIntervalGeneralGroup | current | Collection of general objects needed for managing the interval performance parameters. | |
| 1.3.6.1.2.1.10.2.1.14 | GrouppwVcPeformanceIntervalGroup | current | Collection of 32 bits objects needed for PW performance collection in 15 minutes intervals. | |
| 1.3.6.1.2.1.10.2.1.15 | GrouppwVcHCPeformanceIntervalGroup | current | Collection of HC objects needed for PW performance collection in 15 minutes intervals. | |
| 1.3.6.1.2.1.10.2.1.16 | GrouppwVcMappingTablesGroup | current | Collection of objects contained in the reverse mapping tables. | |
| 1.3.6.1.2.1.10.2.1.17 | GrouppwVcNotificationControlGroup | current | Collection of objects for controlling the PW notifications. | |
| 1.3.6.1.2.1.10.2.1.18 | GrouppwVcNotificationGroup | current | Collection PW notifications objects. | |
| 1.3.6.1.2.1.10.2.2 | NodepwVcCompliances | |||
| 1.3.6.1.2.1.10.2.2.1 | CompliancepwVcModuleFullCompliance | current | The compliance statement for agents that provide full support for PW MIB Module. Such devices can then be monitored and also be configured using this MIB modul… | |
| 1.3.6.1.2.1.10.2.2.2 | CompliancepwVcModuleReadOnlyCompliance | read-only | current | The compliance statement for agents that provide read only support for PW MIB Module. Such devices can then be monitored but cannot be configured using this MI… |