RAD-BROADBAND-IF-MIB
117 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.1.6.8 | NodebroadbandIf | |||
| 1.3.6.1.4.1.164.3.1.6.8.1 | NodebdbandConfig | |||
| 1.3.6.1.4.1.164.3.1.6.8.1.1 | TableprtBdbandIndTable | not-accessible | current | The Indication Signal table. |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1 | RowprtBdbandIndEntry | not-accessible | current | An entry in the Indication Signal table. |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1.1 | ColumnprtBdbandCnfgIdx | read-only | current | This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Ag… |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1.2 | ColumnprtBdbandIdx | read-only | current | This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex. |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1.3 | ColumnprtBdbandIndSig | read-only | current | This object indicates a unique Indication Signal. ais(1) = AIS = Alarm Indication Signal. rdi(2) = RDI = Remote Defect Indication. |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1.4 | ColumnprtBdbandIndEvent | read-only | current | This object indicates a unique Event that can cause the Indication Signal. slm(2) = SLM = Signal Label Mismatch eed(4) = EED = Excessive Error Defect pathTrace… |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1.5 | ColumnprtBdbandIndSigEnable | read-create | current | This object allows user to define if the event specified by prtBdbandIndEvent will cause creation of the Indication Signal specified by prtBdbandIndSig or not.… |
| 1.3.6.1.4.1.164.3.1.6.8.1.1.1.6 | ColumnprtBdbandRowStatus | read-create | current | Creation/Deletion of rows in the table. |
| 1.3.6.1.4.1.164.3.1.6.8.1.2 | TableprtPhyConfigTable | not-accessible | current | The Phy Config table. Used now for Phy25.6 Mbps. |
| 1.3.6.1.4.1.164.3.1.6.8.1.2.1 | RowprtPhyConfigEntry | not-accessible | current | An entry in the Phy Config table. |
| 1.3.6.1.4.1.164.3.1.6.8.1.2.1.1 | ColumnprtPhyTimeElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.4.1.164.3.1.6.8.1.2.1.2 | ColumnprtPhyValidIntervals | read-only | current | The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in … |
| 1.3.6.1.4.1.164.3.1.6.8.2 | NodeprtPhyPerfHistory | |||
| 1.3.6.1.4.1.164.3.1.6.8.2.1 | TableprtPhyCurrentTable | not-accessible | current | The 25.6 Mbps Section/Line Current table. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1 | RowprtPhyCurrentEntry | not-accessible | current | An entry in the 25.6 Mbps Line Current table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.1 | ColumnprtPhyCurrentLOS | read-only | current | The counter associated with the number of Loss Of Sync seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.2 | ColumnprtPhyCurrentLSV | read-only | current | The counter associated with the number of Line symbol violation seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.3 | ColumnprtPhyCurrentUAS | read-only | current | The counter associated with the number of UAS encountered by a 25.6 Mbps interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.4 | ColumnprtPhyCurrentSES | read-only | current | The counter associated with the number of SES encountered by a 25.6 Mbps interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.5 | ColumnprtPhyCurrentES | read-only | current | The number of Errored Seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.6 | ColumnprtPhyCurrentStatus | read-only | current | The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out. |
| 1.3.6.1.4.1.164.3.1.6.8.2.1.1.7 | ColumnprtPhyCurrentLOF | read-only | current | The number of Loss of Frames, encountered by an interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2 | TableprtPhyIntervalTable | not-accessible | current | The Line Interval table. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1 | RowprtPhyIntervalEntry | not-accessible | current | An entry in the 25.6 Mbps Line Interval table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.1 | ColumnprtPhyIntervalNumber | read-only | current | A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that … |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.2 | ColumnprtPhyIntervalLOS | read-only | current | The counter associated with the number of Loss Of Sync seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.3 | ColumnprtPhyIntervalLSV | read-only | current | The counter associated with the number of line symbol violation seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute … |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.4 | ColumnprtPhyIntervalUAS | read-only | current | The counter associated with the number of UAS encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.5 | ColumnprtPhyIntervalSES | read-only | current | The counter associated with the number of SES encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.6 | ColumnprtPhyIntervalES | read-only | current | The number of Errored Seconds, encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.7 | ColumnprtPhyIntervalStatus | read-only | current | The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out. |
| 1.3.6.1.4.1.164.3.1.6.8.2.2.1.8 | ColumnprtPhyIntervalLOF | read-only | current | The number of Loss of Frames, encountered by an interface in one of the previous 96, individual 15 minute intervals. |
| 1.3.6.1.4.1.164.3.1.6.9 | Noder2If | |||
| 1.3.6.1.4.1.164.3.1.6.9.1 | Noder2ProfileCnfg | |||
| 1.3.6.1.4.1.164.3.1.6.9.1.1 | Tabler2CnfgTable | not-accessible | current | The write operation into the Table Objects is valid only to the TmpCnfg entry. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1 | Rowr2CnfgEntry | not-accessible | current | An entry in table. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.1 | Columnr2CnfgIdx | read-only | current | This attribute indicates the Idx of the Cnfg being accessed. 255 = TmpCnfg. 1 = Current Cnfg. Write is allowed only to TmpCnfg. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.2 | Columnr2CnfgProfileIdx | read-only | current | Profile Index. Valid values: 1..5 Only instances of profiles that are defined having agnSigProfType=r2Cas will exist in this table. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.3 | Columnr2Mode | read-create | current | R2 Mode. auto - in this mode, default value of timers will be used by R2, according to the selected r2Country. manual - in this mode, user can change the value… |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.4 | Columnr2Country | read-create | current | R2 Country. R2 Timers can have different range of values and defaults for each country. When r2Mode=auto, the default value is used by R2 according to this sel… |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.5 | Columnr2Delay | read-create | current | This object enables user to configure the link as satellite or terrestrial. The seize acknowledge detect timing is much shorter (msec) for terrestrial link tha… |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.6 | Columnr2MeteringInd | read-create | current | Which Bit will be used for Metering Indication. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.7 | Columnr2BreakMakeRatio | read-create | current | This object describes the Break-Make Ratio of Pulse Duration, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.8 | Columnr2ReleaseGuardT2 | read-create | current | Release Guard timing T2. Release guard timing before going to idle, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.9 | Columnr2Regret | read-create | current | Regret duration, in [sec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.10 | Columnr2SeizeDetect | read-create | current | Seize Detect. Timer of the R2 incoming side. Minimum duration to detect a valid seizure, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.11 | Columnr2SeizeAckDelay | read-create | current | Timer of the R2 incoming side. Delay before sending a valid seize ack signal, in [msec]. Applicable only when r2Mode=manual. only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.12 | Columnr2ClearBackDetect | read-create | current | Timer of the R2 incoming side. Minimum duration to recognize a valid clear-back, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.13 | Columnr2ClearFwdDetect | read-create | current | Timer of the R2 incoming side. Minimum duration to recognize a valid clear-forward, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.14 | Columnr2FaultDetect | read-create | current | Timer of the R2 incoming side. Minimum duration to recognize a block signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.15 | Columnr2FaultRemoveDetect | read-create | current | Timer of the R2 incoming side. Minimum duration to recognize a valid block removal signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.16 | Columnr2MeterPulseDuration | read-create | current | Timer of the R2 incoming side. Duration of metering pulse to be sent, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.17 | Columnr2SeizeAckWait | read-create | current | Timer of the R2 outgoing side. Minimum duration to receive seizure acknowledge signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.18 | Columnr2SeizeAckDetect | read-create | current | Timer of the R2 outgoing side. Minimum duration to recognize a valid seizure acknowledge signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.19 | Columnr2AnswerDetect | read-create | current | Timer of the R2 outgoing side. Minimum duration to recognize a valid answer signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.20 | Columnr2BlockRemoveDetect | read-create | current | Timer of the R2 outgoing side. Minimum duration to recognize a valid block removal signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.21 | Columnr2MeterPulseDetect | read-create | current | Timer of the R2 outgoing side. Minimum duration of incoming meter pulse, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.22 | Columnr2ForcedDisconnect | read-create | current | Timer of the R2 outgoing side. Minimum duration to recognize disconnect signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.23 | Columnr2DisconnectAck | read-create | current | Timer of the R2 outgoing side. Minimum duration to recognize disconnect acknowledge signal, in [msec]. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.24 | Columnr2ReleaseGuardT1 | read-create | current | Timer of the R2 outgoing side. Minimum duration to release guard, in [msec]. During this time, no new call can be initiated. RW only when r2Mode=manual. |
| 1.3.6.1.4.1.164.3.1.6.9.1.1.1.25 | Columnr2CnfgRowStatus | read-create | current | This object enables the user to add/delete entries to/from the table. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2 | Tabler2TsTable | not-accessible | current | The write operation into the Table Objects is valid only to the TmpCnfg entry. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1 | Rowr2TsEntry | not-accessible | current | An entry in table. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.1 | Columnr2TsCnfgIdx | read-only | current | This attribute indicates the Idx of the Cnfg being accessed. 255 = TmpCnfg. 1 = Current Cnfg. Write is allowed only to TmpCnfg. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.2 | Columnr2TsProfileIdx | read-only | current | Profile Index. Valid values: 1..5 Only instances of profiles that are defined having agnSigProfType=r2Cas will exist in this table. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.3 | Columnr2TsIdx | read-only | current | TS Index. Valid values: 1..31 |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.4 | Columnr2TsCallEnable | read-create | current | This object indicates the Enabled Call direction for the specific TS. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.5 | Columnr2TsMetering | read-create | current | This object indicates if the specific TS should support Metering. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.6 | Columnr2TsRowStatus | read-create | current | This object enables the user to add/delete entries to/from the table. |
| 1.3.6.1.4.1.164.3.1.6.9.1.2.1.7 | Columnr2TsReversePolarity | read-create | current | This object indicates if the specific TS should support Reverse Polarity. |
| 1.3.6.1.4.1.164.3.1.6.9.2 | Noder2IfStatus | |||
| 1.3.6.1.4.1.164.3.1.6.9.2.1 | Tabler2StatusTable | not-accessible | current | The write operation into the Table Objects is valid only to the TmpCnfg entry. |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1 | Rowr2StatusEntry | not-accessible | current | An entry in table. |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1.1 | Columnr2StatusSlotIdx | read-only | current | Slot Index |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1.2 | Columnr2StatusPortIdx | read-only | current | This object indicates a unique port number of the ML having R2 interface. Valid values: exPrt1 (1)..exPrt4 (4) |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1.3 | Columnr2StatusTsIdx | read-only | current | Time Slot index. |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1.4 | Columnr2StatusSigDirection | read-only | current | R2 Time Slot Signaling Direction. |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1.5 | Columnr2StatusTsState | read-only | current | R2 TS State |
| 1.3.6.1.4.1.164.3.1.6.9.2.1.1.6 | Columnr2StatusProtocolState | read-only | current | R2 Protocol State. |
| 1.3.6.1.4.1.164.12.7 | NodeatmLayer2 | |||
| 1.3.6.1.4.1.164.12.7.1 | TableatmLayer2XVclTable | not-accessible | current | This table is an extension of VCL table, which is created for each LAN VCC. |
| 1.3.6.1.4.1.164.12.7.1.1 | RowatmLayer2XVclEntry | not-accessible | current | Conceptual row in atmVclTable. This table augments the RFC2515 VCL table. |
| 1.3.6.1.4.1.164.12.7.1.1.1 | ColumnatmLayer2XVclConnMode | read-create | current | Each valid LAN VCC is either Main or Sub. This parameter is configured only once on creation of a LAN VCC. It can not be changed after creation. In order to ch… |
| 1.3.6.1.4.1.164.12.7.1.1.2 | ColumnatmLayer2XVclGroupIdx | read-only | current | The group identifier. A VCC Group identifier = 0 if the VCC was not associated with a group yet. This value is updated according to the group identifier set by… |
| 1.3.6.1.4.1.164.12.7.2 | TableatmLayer2GroupTable | not-accessible | current | This table contains groups and their members. A group is a bundle of VCCs, which acts as different queues. Main and Sub VCCs should have the same ATM slot and … |
| 1.3.6.1.4.1.164.12.7.2.1 | RowatmLayer2GroupEntry | not-accessible | current | Conceptual row in atmLayer2GroupTable. The indexes: ifIndex, atmVclVpi and atmVclVci indicate the Network ATM End-Point. Upon a group creation, one Main VCC mu… |
| 1.3.6.1.4.1.164.12.7.2.1.1 | ColumnatmLayer2GroupIdx | read-only | current | The group identifier. 0 is not a valid index. |
| 1.3.6.1.4.1.164.12.7.2.1.2 | ColumnatmLayer2GroupRowStatus | read-create | current | Creation/Deletion of rows in the table, and indication of the entry's status. |
| 1.3.6.1.4.1.164.12.7.2.1.3 | ColumnatmLayer2GroupConnMode | read-only | current | Each valid LAN VCC is either Main or Sub as configured in atmLayer2XVclTable. |
| 1.3.6.1.4.1.164.12.7.2.1.4 | ColumnatmLayer2GroupConnPriority | read-only | current | This parameter is configured by atmLayer2PriorityRx from atmLayer2PriorityTable. Each bit in the Octet represents a specific priority as follows: MSB 7 6 5 4 3… |
| 1.3.6.1.4.1.164.12.7.2.1.5 | ColumnatmLayer2GroupName | read-create | current | Group name. Configured by the user. The name is unique per system. For atmLayer2GroupIdx=0, the name will be null. |
| 1.3.6.1.4.1.164.12.7.3 | TableatmLayer2PriorityTable | not-accessible | current | This table maps all priorities inside a group. Several priorities might be mapped to the same VCC. Upon priority change, the agent will update the VCCs of the … |
| 1.3.6.1.4.1.164.12.7.3.1 | RowatmLayer2PriorityEntry | not-accessible | current | Conceptual row in atmLayer2PriorityTable. Each entry is a Network ATM End-Point per priority. Upon a group creation, all priorities are mapped to the Main VCC.… |
| 1.3.6.1.4.1.164.12.7.3.1.1 | ColumnatmLayer2PriorityGroupIdx | read-only | current | The group identifier. |
| 1.3.6.1.4.1.164.12.7.3.1.2 | ColumnatmLayer2PriorityRx | read-only | current | The priority values. The used values are 0-7, but since this value is part of the index of the table, and in order to avoid '0' as an index, the index syntax i… |
| 1.3.6.1.4.1.164.12.7.3.1.3 | ColumnatmLayer2PriorityIfIndex | read-create | current | ATM ifIndex of the network End-Point. |
| 1.3.6.1.4.1.164.12.7.3.1.4 | ColumnatmLayer2PriorityVclVpi | read-create | current | Vpi of the network End-Point. |
| 1.3.6.1.4.1.164.12.7.3.1.5 | ColumnatmLayer2PriorityVclVci | read-create | current | Vci of the network End-Point. |
| 1.3.6.1.4.1.164.12.7.4 | ScalaratmLayer2GroupIndexNext | read-only | current | This object contains an appropriate value to be used for atmLayer2GroupIdx when creating entries in the atmLayer2GroupTable. The value 0 indicates that no unas… |
| 1.3.6.1.4.1.164.12.7.5 | TableatmLayer2CfgTable | not-accessible | current | Bridge configuration Table. This table supports multi-bridge and bridge features within an ATM device. |
| 1.3.6.1.4.1.164.12.7.5.1 | RowatmLayer2CfgEntry | not-accessible | current | Conceptual row in atmLayer2CfgTable. Each entry in this table contains the bridging attributes for both Ethernet and ATM sides. The interface index is the Ethe… |
| 1.3.6.1.4.1.164.12.7.5.1.1 | ColumnatmLayer2CfgBridgingMode | read-write | current | Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> … |
| 1.3.6.1.4.1.164.12.7.5.1.2 | ColumnatmLayer2CfgVlanMode | read-write | current | VLAN Mode. Upon Mode changing, all LAN VCCs will be deleted by the agent from all tables that include LAN VCCs. |
| 1.3.6.1.4.1.164.12.7.5.1.3 | ColumnatmLayer2CfgAtmAcceptableFrameType | read-write | current | The Frame Type that will be acceptable by the VCCs that are associated with this Ethernet port. Frames which don't match the selected type will be discarded. a… |
| 1.3.6.1.4.1.164.12.7.5.1.4 | ColumnatmLayer2CfgAtmIngressFiltering | read-write | current | For the VCCs that are associated with this Ethernet port, when this is true(1) the device will discard incoming frames for VLANs which do not include this Port… |
| 1.3.6.1.4.1.164.12.7.5.1.5 | ColumnatmLayer2CfgAtmTxFrameType | read-write | current | The Frame Type that will be transmitted by the VCCs that are associated with this Ethernet port. unTagged - The transmitted frames will be unTagged. tagged - T… |
| 1.3.6.1.4.1.164.12.7.5.1.6 | ColumnatmLayer2CfgEthAcceptableFrameType | read-write | current | The Frame Type that this Ethernet port will accept. (for ACE-52: the Frame Type that this Bridge will accept) This parameter is notApplicable for atmLayer2Vlan… |
| 1.3.6.1.4.1.164.12.7.5.1.7 | ColumnatmLayer2CfgBridgeAction | read-write | current | This object enables to perform the specified action on the selected port. |
| 1.3.6.1.4.1.164.12.7.5.1.8 | ColumnatmLayer2CfgLearningMode | read-write | current | This object specifies the mode of the learning process of a bridge. svl - Shared VLAN process. If an individual MAC Address is learned in one VLAN, this inform… |
| 1.3.6.1.4.1.164.12.7.5.1.9 | ColumnatmLayer2CfgAgingTime | read-write | current | The timeout period in seconds for aging out dynamically learned forwarding information. |
| 1.3.6.1.4.1.164.12.8 | NoderadAtmFr | |||
| 1.3.6.1.4.1.164.12.8.1 | TablefrAtmIwfXConnectionTable | not-accessible | current | This table is an extension of frAtmIwfXConnectionTable from RFC2955. |
| 1.3.6.1.4.1.164.12.8.1.1 | RowfrAtmIwfXConnectionEntry | not-accessible | current | Conceptual row in frAtmIwfXConnectionTable. This table augments the RFC2955. |
| 1.3.6.1.4.1.164.12.8.1.1.1 | ColumnfrAtmIwfXConnMode | read-create | current | FR IWF Mode. service - Service InterWorking (FRF.8), network - Network InterWorking (FRF.5). |
| 1.3.6.1.4.1.164.12.8.1.1.2 | ColumnfrAtmIwfXConnSscsDlci | read-create | current | This parameter is relevant for frAtmIwfXConnMode=network (FRF.5) only. This parameter allow configuration of the FR SSCS DLCI that is transferred to the remote… |