RAID-Adapter-MIB
195 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises |
| RFC1213-MIB | -- PhysAddress DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3582 | Nodelsi | |||
| 1.3.6.1.4.1.3582.1 | NodemegaRaid | |||
| 1.3.6.1.4.1.3582.1.1 | NodemegaRaidMib | |||
| 1.3.6.1.4.1.3582.1.1.1 | TableadapterTable | not-accessible | optional | A List of Adapter Entries containing Information/Properties about the Adapters in the System. |
| 1.3.6.1.4.1.3582.1.1.1.1 | RowadapterEntry | not-accessible | optional | An entry in the Adapter Table. Each Entry corresponds to one Adapter in the System. |
| 1.3.6.1.4.1.3582.1.1.1.1.1 | ColumnadpAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter Object. This Entry in the Table, contains Information about the Adapter Number specified by this variable. |
| 1.3.6.1.4.1.3582.1.1.1.1.2 | ColumnnumLogicalDrives | read-only | optional | Number of Logical Drives Configured on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.3 | ColumnfirmwareVersion | read-only | optional | The Firmware Version of the Firmware running on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.4 | ColumnbiosVersion | read-only | optional | The Bios Version of the BIOS Present in the Flash ROM on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.5 | ColumndramSizeInMB | read-only | optional | Amount of DRAM in Mega Bytes present on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.6 | ColumnrebuildRateInPercent | read-write | optional | Rebuild Rate for this Adapter. This determines the Priority of Rebuild/Check-Consistency/Reconstruct Operations versus the Read-Write Operations. |
| 1.3.6.1.4.1.3582.1.1.1.1.7 | ColumnflushInterval | read-write | optional | Internal Cache Flush Interval for Logical Drives in WriteBack Mode. |
| 1.3.6.1.4.1.3582.1.1.1.1.8 | ColumnmaxConcurrentCmds | read-only | optional | Maximum Concurrent Commands Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.9 | ColumnspinupDelay | read-only | optional | This is the Spinup Delay for Spinning Up Physical Drives at Firmware Initialization Time. The Physical Drives are divided into Groups, each containing the numb… |
| 1.3.6.1.4.1.3582.1.1.1.1.10 | ColumnspinupCount | read-only | optional | This is the Spinup Count for Spinning up Physical Drives at Firmware Initialization Time. The Physical Drives are divided into Groups, each containing the numb… |
| 1.3.6.1.4.1.3582.1.1.1.1.11 | ColumnadpIOReadsPerSec | read-only | optional | Number of IO Reads/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.12 | ColumnadpIOWritesPerSec | read-only | optional | Number of IO Writes/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.13 | ColumnadpReadKBsPerSec | read-only | optional | Amount of Data Transferred in KBs/sec due to READ Transfers. |
| 1.3.6.1.4.1.3582.1.1.1.1.14 | ColumnadpWriteKBsPerSec | read-only | optional | Amount of Data Transferred in KBs/sec due to WRITE Transfers. |
| 1.3.6.1.4.1.3582.1.1.1.1.15 | ColumnadpReadFailuresPerSec | read-only | optional | Number of Read-Failures/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.16 | ColumnadpWriteFailuresPerSec | read-only | optional | Number of Write-Failures/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.17 | ColumnscanChannels | read-write | optional | Use this Variable to Discover the Non-Disk Devices attached to the Adapter. Set this Variable to startscan (an integer value of 2) to start the Channel Scannin… |
| 1.3.6.1.4.1.3582.1.1.1.1.18 | ColumnadpBasePort | read-only | optional | Maximum Concurrent Commands Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.19 | ColumnnumSCSIChannels | read-only | optional | Maximum number of SCSI Channels Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.20 | ColumnnumFCLoops | read-only | optional | Number of Fibre channel loops Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.21 | ColumnsubSystemID | read-only | optional | The PCI sub system ID of this controller |
| 1.3.6.1.4.1.3582.1.1.1.1.22 | ColumnsubSystemVendorID | read-only | optional | The PCI sub system vendor ID of this controller |
| 1.3.6.1.4.1.3582.1.1.1.1.23 | ColumnproductName | read-only | optional | The enriched formation of the controller retrieved from the firmware |
| 1.3.6.1.4.1.3582.1.1.1.1.24 | ColumnadpSpeed | read-only | optional | Maximum transfer speed of the adapter. |
| 1.3.6.1.4.1.3582.1.1.2 | TablelogicaldriveTable | not-accessible | optional | A List of Logical Drive Entries containing Information/Properties about the Logical Drives Configured in the System. |
| 1.3.6.1.4.1.3582.1.1.2.1 | RowlogicaldriveEntry | not-accessible | optional | An Entry in the Logical Drive Table. |
| 1.3.6.1.4.1.3582.1.1.2.1.1 | ColumnldAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter/LogicalDrive object. |
| 1.3.6.1.4.1.3582.1.1.2.1.2 | ColumnlogicalDriveNumber | read-only | optional | Logical Drive Number for this Logical Drive Entry. |
| 1.3.6.1.4.1.3582.1.1.2.1.3 | Columnstatus | read-write | optional | The Status of this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.4 | ColumnsizeInMB | read-only | optional | The Configured Size of this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.5 | ColumnraidLevel | read-only | optional | Configured Raid Level for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.6 | ColumnstripeSize | read-only | optional | Configured Stripe Size for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.7 | ColumnreadPolicy | read-write | optional | Configured Read Policy for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.8 | ColumnwritePolicy | read-write | optional | Configured Write Policy for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.9 | ColumncachePolicy | read-write | optional | Configured Cache Policy for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.10 | ColumnenquiryString | read-only | optional | SCSI Inquiry String for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.11 | ColumnnumberOfSpans | read-only | optional | Number of Arrays across which this Logical Drive is Spanning. |
| 1.3.6.1.4.1.3582.1.1.2.1.12 | ColumnnumberOfStripes | read-only | optional | Configured Number of Stripes for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.13 | ColumncheckConsistencyOrInitializeProgress | read-only | optional | Check Consistency or Initialize Progress for this Logical Drive if the Logical Drive Status is checkconsistencyinprogress or initializeinprogress. |
| 1.3.6.1.4.1.3582.1.1.2.1.14 | ColumnldIOReadsPerSec | read-only | optional | Number of IO Reads/sec Statistics for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.15 | ColumnldIOWritesPerSec | read-only | optional | Number of IO Writes/sec Statistics for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.16 | ColumnldReadKBsPerSec | read-only | optional | Amount of Data Transferred in KBs/sec due to READ Transfers. |
| 1.3.6.1.4.1.3582.1.1.2.1.17 | ColumnldWriteKBsPerSec | read-only | optional | Amount of Data Transferred in KBs/sec due to WRITE Transfers. |
| 1.3.6.1.4.1.3582.1.1.2.1.18 | ColumnldReadFailuresPerSec | read-only | optional | Number of Read-Failures/sec Statistics for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.2.1.19 | ColumnldWriteFailuresPerSec | read-only | optional | Number of Write-Failures/sec Statistics for this Logical Drive. |
| 1.3.6.1.4.1.3582.1.1.3 | TablephysicaldriveTable | not-accessible | optional | A List of Physical Device Entries containing Information about the Physical Devices in the System. |
| 1.3.6.1.4.1.3582.1.1.3.1 | RowphysicaldriveEntry | not-accessible | optional | An Entry in the Physical Drive Table. |
| 1.3.6.1.4.1.3582.1.1.3.1.1 | ColumnphysAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter/Physical-Drive Instance. |
| 1.3.6.1.4.1.3582.1.1.3.1.2 | ColumnphysChannel | read-only | optional | Channel Number at Which this Physical Drive is Present. |
| 1.3.6.1.4.1.3582.1.1.3.1.3 | ColumntargetID | read-only | optional | SCSI Target ID at Which This Physical Drive is Present. |
| 1.3.6.1.4.1.3582.1.1.3.1.4 | Columnstate | read-write | optional | Current State of this Physical Drive. |
| 1.3.6.1.4.1.3582.1.1.3.1.5 | ColumnarrayPosition | read-only | optional | Array is a group of Physical Drives used to Configure Logical Drives. This String Variable has values of the type Ai-j. Example: A1-2 implies that this drive i… |
| 1.3.6.1.4.1.3582.1.1.3.1.6 | ColumnsizeMB | read-only | optional | Actual Size of this Physical Drive. |
| 1.3.6.1.4.1.3582.1.1.3.1.7 | ColumndeviceType | read-only | optional | Device Type of this Physical Drive. |
| 1.3.6.1.4.1.3582.1.1.3.1.8 | ColumninquiryString | read-only | optional | SCSI Inquiry String for this Device. |
| 1.3.6.1.4.1.3582.1.1.3.1.9 | ColumnscsiLevel | read-only | optional | ANSI SCSI Level Conformance of this Device. |
| 1.3.6.1.4.1.3582.1.1.3.1.10 | ColumnmaximumQueueDepth | read-only | optional | The maximum queue depth of this Device. |
| 1.3.6.1.4.1.3582.1.1.3.1.11 | ColumnrebuildProgress | read-only | optional | Rebuild Progress for this Physical Drive if the Physical Drive State is Rebuild. |
| 1.3.6.1.4.1.3582.1.1.3.1.12 | ColumnmediumErrors | read-only | optional | Medium Errors Occurred on this Drive Since it was Configured. |
| 1.3.6.1.4.1.3582.1.1.3.1.13 | ColumnphysSlotStatus | read-only | optional | Indicates the status of interest on the drive slot |
| 1.3.6.1.4.1.3582.1.1.3.1.14 | ColumnphysSlotNumber | read-only | optional | SCSI Target Slot Number at Which This Physical Drive is Present. |
| 1.3.6.1.4.1.3582.1.1.3.1.15 | ColumnotherErrors | read-only | optional | Other Errors Occurred on this Drive Since it was Configured. |
| 1.3.6.1.4.1.3582.1.1.3.1.16 | ColumnphysTermination | read-only | optional | Negotiation Information of the physical drive. This field is applicable only to drives. |
| 1.3.6.1.4.1.3582.1.1.3.1.17 | ColumnphysSpeed | read-only | optional | Transfer speed of the physical drive. This field is applicable only to drives. |
| 1.3.6.1.4.1.3582.1.1.3.1.18 | ColumnlunNumber | read-only | optional | SCSI LUN ID of this Physical Device |
| 1.3.6.1.4.1.3582.1.1.4 | TablechannelTable | not-accessible | optional | A List of Channel Entries containing Information/Properties about the Channels on the Adapter. |
| 1.3.6.1.4.1.3582.1.1.4.1 | RowchannelEntry | not-accessible | optional | An Entry in the channel table. |
| 1.3.6.1.4.1.3582.1.1.4.1.1 | ColumnchanAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter/Channel Instance. |
| 1.3.6.1.4.1.3582.1.1.4.1.2 | Columnchannel | read-only | optional | Channel Number for this Channel. |
| 1.3.6.1.4.1.3582.1.1.4.1.3 | Columnterminations | read-only | optional | Current Terminations Effective on this Channel |
| 1.3.6.1.4.1.3582.1.1.4.1.4 | ColumnchannelStatus | read-only | optional | Current Activity Status (QUIET/ACTIVE) for this Channel. |
| 1.3.6.1.4.1.3582.1.1.4.1.5 | ColumnchannelType | read-only | mandatory | Type of the channel(RAID/SCSI). |
| 1.3.6.1.4.1.3582.1.1.5 | TablefcDeviceTable | not-accessible | optional | A List of Entries containing Information about the FC Devices in the System. |
| 1.3.6.1.4.1.3582.1.1.5.1 | RowfcDeviceEntry | not-accessible | optional | An Entry in the FC Device Table. |
| 1.3.6.1.4.1.3582.1.1.5.1.1 | ColumnfcPhysAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter/Physical-Drive Instance. |
| 1.3.6.1.4.1.3582.1.1.5.1.2 | ColumnfcPhysChannel | read-only | optional | The Channel Number for this Instance of Adapter/Physical-Drive |
| 1.3.6.1.4.1.3582.1.1.5.1.3 | ColumnfcTargetId | read-only | optional | The Target Number for this Instance of Adapter/Physical-Drive |
| 1.3.6.1.4.1.3582.1.1.5.1.4 | ColumnfcLoopID-0 | read-only | optional | Loop ID of this FC Drive. |
| 1.3.6.1.4.1.3582.1.1.5.1.5 | ColumnfcLoopID-1 | read-only | optional | Loop ID of this FC Drive. |
| 1.3.6.1.4.1.3582.1.1.5.1.6 | ColumnfcWwn | read-only | optional | WWN is the World Wide Name of this FC device |
| 1.3.6.1.4.1.3582.1.1.5.1.7 | ColumnfcState | read-write | optional | Current State of this Physical Drive. |
| 1.3.6.1.4.1.3582.1.1.5.1.8 | ColumnfcArrayPosition | read-only | optional | Array is a group of Physical Drives used to Configure Logical Drives. This String Variable has values of the type Ai-j. Example: A1-2 implies that this drive i… |
| 1.3.6.1.4.1.3582.1.1.5.1.9 | ColumnfcSizeMB | read-only | optional | Actual Size of this Physical Drive. |
| 1.3.6.1.4.1.3582.1.1.5.1.10 | ColumnfcInquiryString | read-only | optional | SCSI Inquiry String for this Device. |
| 1.3.6.1.4.1.3582.1.1.5.1.11 | ColumnfcScsiLevel | read-only | optional | ANSI SCSI Level Conformance of this Device. |
| 1.3.6.1.4.1.3582.1.1.5.1.12 | ColumnfcRebuildProgress | read-only | optional | Rebuild Progress for this Physical Drive if the Physical Drive State is Rebuild. |
| 1.3.6.1.4.1.3582.1.1.5.1.13 | ColumnfcMediumErrors | read-only | optional | Medium Errors Occurred on this Drive Since it was Configured. |
| 1.3.6.1.4.1.3582.1.1.5.1.14 | ColumnfcOtherErrors | read-only | optional | Other Errors Occurred on this Drive Since it was Configured. |
| 1.3.6.1.4.1.3582.1.1.6 | TablefcChannelTable | not-accessible | optional | A List of FC Channel Entries containing Information about the FC Channels on the Adapter. |
| 1.3.6.1.4.1.3582.1.1.6.1 | RowfcChannelEntry | not-accessible | optional | An Entry in the FC channel table. |
| 1.3.6.1.4.1.3582.1.1.6.1.1 | ColumnfcChanAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter/fc-Channel Instance. |
| 1.3.6.1.4.1.3582.1.1.6.1.2 | ColumnfcChannel | read-only | optional | The Channel Number for this Instance |
| 1.3.6.1.4.1.3582.1.1.6.1.3 | ColumnfcLoopNumber | read-only | optional | Loop Index for this fcChannel. |
| 1.3.6.1.4.1.3582.1.1.6.1.4 | ColumnfcLoopStatus | read-only | optional | Current Activity Status (QUIET/ACTIVE) for this fcChannel. |
| 1.3.6.1.4.1.3582.1.1.6.1.5 | ColumnfcNumberofDevices | read-only | optional | The number of FC devices in this fcChannel |
| 1.3.6.1.4.1.3582.1.1.6.1.6 | ColumnfcProcessorType | read-only | optional | The processor type on this fcChannel |
| 1.3.6.1.4.1.3582.1.1.9 | ScalarioReadsPerSec | read-only | optional | The Total IO-Reads/Sec Statistics on all Adapters. |
| 1.3.6.1.4.1.3582.1.1.10 | ScalarioWritesPerSec | read-only | optional | The Total IO-Writes/Sec Statistics on all Adapters. |
| 1.3.6.1.4.1.3582.1.1.11 | ScalarreadKBsPerSec | read-only | optional | The Total Read KBs Per Second Statistics on all Adapters. |
| 1.3.6.1.4.1.3582.1.1.12 | ScalarwriteKBsPerSec | read-only | optional | The Total Write KBs Per Second Statistics on all Adapters. |
| 1.3.6.1.4.1.3582.1.1.13 | ScalarreadFailuresPerSec | read-only | optional | The Total Read Failures Per Second Statistics on all Adapters. |
| 1.3.6.1.4.1.3582.1.1.14 | ScalarwriteFailuresPerSec | read-only | optional | The Total Write Failures Per Second Statistics on all Adapters. |
| 1.3.6.1.4.1.3582.1.1.15 | TableenclConfigurationTable | not-accessible | optional | A List of Enclosure Configuration Entries containing Information about the SAF-TE Enclosures in the System. |
| 1.3.6.1.4.1.3582.1.1.15.1 | RowenclConfigurationEntry | not-accessible | optional | An Entry in the Enclosure Configuration Table. |
| 1.3.6.1.4.1.3582.1.1.15.1.1 | ColumnenclAdapterNumber | read-only | optional | The Adapter Number for this Instance of Adapter/Enclosure Instance. |
| 1.3.6.1.4.1.3582.1.1.15.1.2 | ColumnenclNumber | read-only | optional | Indicates the enclosure number for this Enclosure. The numbering is w.r.t adapter and not w.r.t Channel |
| 1.3.6.1.4.1.3582.1.1.15.1.3 | ColumnenclChannel | read-only | optional | Channel Number at Which this Enclosure is Present. |
| 1.3.6.1.4.1.3582.1.1.15.1.4 | ColumnenclNumDeviceSlots | read-only | optional | Total number of device slots on the channel for this Enclosure |
| 1.3.6.1.4.1.3582.1.1.15.1.5 | ColumnenclNumFans | read-only | optional | Total number SEP manageable of fans for this Enclosure |
| 1.3.6.1.4.1.3582.1.1.15.1.6 | ColumnenclNumTempSensors | read-only | optional | Number of SEP manageable Temperature Sensors for this Enclosure |
| 1.3.6.1.4.1.3582.1.1.15.1.7 | ColumnenclNumPowerSupplies | read-only | optional | Maximum number of SEP manageable Power Supplies for this Enclosure |
| 1.3.6.1.4.1.3582.1.1.15.1.8 | ColumnenclDoorLockStatus | read-only | optional | Indicates whether this enclosure has door lock installed/locked/unlocked |
| 1.3.6.1.4.1.3582.1.1.15.1.9 | ColumnenclAudibleAlarm | read-only | optional | Indicates the availability of Audible Alarm with this Enclosure |
| 1.3.6.1.4.1.3582.1.1.15.1.10 | ColumnenclAlarmStatus | read-only | optional | Indicates whether this Enclosure speaker is ON or OFF |
| 1.3.6.1.4.1.3582.1.1.15.1.11 | ColumnenclTemperatureScale | read-only | optional | Indicates whether this Enclosure reports temperature in Celsius or Fahrenheit |
| 1.3.6.1.4.1.3582.1.1.15.1.12 | ColumnenclTotalPowerOnMins | read-only | optional | This indicates the total time in minutes that the RAID device has been powered ON. It is cumulative over the life of the device |
| 1.3.6.1.4.1.3582.1.1.15.1.13 | ColumnenclTotalPowerOnCycles | read-only | optional | This indicates the count of number of times that the RAID device has been powered ON. It is cumulative over the life of the device |
| 1.3.6.1.4.1.3582.1.1.16 | TableenclFanTable | not-accessible | optional | A List of SAF-TE Enclosure Fan Entries |
| 1.3.6.1.4.1.3582.1.1.16.1 | RowenclFanEntry | not-accessible | optional | An Entry in the Enclosure Fan Table. |
| 1.3.6.1.4.1.3582.1.1.16.1.1 | ColumnenclNumberFan | read-only | optional | Enclosure Number at Which this Enclosure with the Fan is Present. |
| 1.3.6.1.4.1.3582.1.1.16.1.2 | ColumnenclFanIndex | read-only | optional | The instance of the fan in the enclosure for the adapter/channel |
| 1.3.6.1.4.1.3582.1.1.16.1.3 | ColumnenclFanStatus | read-only | optional | The Status of this fan |
| 1.3.6.1.4.1.3582.1.1.17 | TableenclPowerSupplyTable | not-accessible | optional | A List of SAF-TE Enclosure Power Supply Entries |
| 1.3.6.1.4.1.3582.1.1.17.1 | RowenclPowerSupplyEntry | not-accessible | optional | An Entry in the Enclosure Power Supply Table. |
| 1.3.6.1.4.1.3582.1.1.17.1.1 | ColumnenclNumberPower | read-only | optional | enclosure number at Which this Enclosure with the Power Supply is Present. |
| 1.3.6.1.4.1.3582.1.1.17.1.2 | ColumnenclPowerSupplyIndex | read-only | optional | The instance of the PowerSupply in the enclosure for the adapter/channel |
| 1.3.6.1.4.1.3582.1.1.17.1.3 | ColumnenclPowerSupplyStatus | read-only | optional | The Status of this PowerSupply |
| 1.3.6.1.4.1.3582.1.1.18 | TableenclTempSensorsTable | not-accessible | optional | A List of SAF-TE Enclosure Temperature Sensor Entries |
| 1.3.6.1.4.1.3582.1.1.18.1 | RowenclTempSensorsEntry | not-accessible | optional | An Entry in the Enclosure Temperature Sensor Table. |
| 1.3.6.1.4.1.3582.1.1.18.1.1 | ColumnenclNumberTemp | read-only | optional | enclosure number at Which this Enclosure with the temperature sensor is Present. |
| 1.3.6.1.4.1.3582.1.1.18.1.2 | ColumnenclTempSensorIndex | read-only | optional | The instance of the temperature sensor indices in the enclosure for the adapter/channel |
| 1.3.6.1.4.1.3582.1.1.18.1.3 | ColumnenclTemperature | read-only | optional | Indicates the temperature reported by the sensor in degree Fahrenheit |
| 1.3.6.1.4.1.3582.1.1.200 | NoderaidTraps | |||
| 1.3.6.1.4.1.3582.1.1.200.1001 | ScalarrtAdapterNumber | read-only | optional | Adapter Number for which Trap is generated. |
| 1.3.6.1.4.1.3582.1.1.200.1002 | ScalarrtLogicalDriveNumber | read-only | optional | Logical Drive Number for which Trap is generated. |
| 1.3.6.1.4.1.3582.1.1.200.1003 | ScalarrtChannelNumber | read-only | optional | Channel Number on the Adapter for which Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1004 | ScalarrtTargetID | read-only | optional | Device ID of the Physical Drive for which Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1005 | ScalarrtOldDriveState | read-only | optional | Old State of Logical/Physical Drive, when a State Change Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1006 | ScalarrtNewDriveState | read-only | optional | New State of Logical/Physical Drive, when a State Change Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1007 | ScalarrtSenseKey | read-only | optional | Check Condition Sense-Key reported by Physical Drive for which Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1008 | ScalarrtASC | read-only | optional | Check Condition Additional Sense Code (ASC) reported by Physical Drive for which Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1009 | ScalarrtASCQ | read-only | optional | Check Condition Additional Sense Code Qualifier (ASCQ) reported by Physical Drive for which Trap is Generated. |
| 1.3.6.1.4.1.3582.1.1.200.1010 | ScalarrtDriveVendor | read-only | optional | Vendor Identification String from the SCSI Inquiry Data for the Drive. |
| 1.3.6.1.4.1.3582.1.1.200.1011 | ScalarrtEnclNumber | read-only | optional | Enclosure Number reported by the RAID Controller. |
| 1.3.6.1.4.1.3582.1.1.200.1012 | ScalarrtEnclTempSensorIndex | read-only | optional | Enclosure Temperature Sensor Number reported by the SEP device |
| 1.3.6.1.4.1.3582.1.1.200.1013 | ScalarrtEnclTemperature | read-only | optional | Enclosure Temperature in Fahrenheit reported by the SEP device |
| 1.3.6.1.4.1.3582.1.1.200.1014 | ScalarrtEnclFanIndex | read-only | optional | Enclosure Fan Number reported by the SEP device |
| 1.3.6.1.4.1.3582.1.1.200.1015 | ScalarrtEnclPowerSupplyIndex | read-only | optional | Enclosure Power Supply Number reported by the SEP device |
| 1.3.6.1.4.1.3582.1.1.200.1016 | ScalarrtWWN | read-only | optional | The World Wide Name of the FC device whose loop ID or State changes |
| 1.3.6.1.4.1.3582.1.1.200.1017 | ScalarrtOldLoopID | read-only | optional | Index of the loop before its state changed |
| 1.3.6.1.4.1.3582.1.1.200.1018 | ScalarrtNewLoopID | read-only | optional | Index of the loop after its state changed |
| 1.3.6.1.4.1.3582.1.1.200.9001 | NodertConfigUpdated | Adapter-%d: A New Configuration has been written. | ||
| 1.3.6.1.4.1.3582.1.1.200.9002 | NodertPhysicalDriveStateChange | Adapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9003 | NodertLogicalDriveStateChange | Adapter-%d, Logical Drive-%d: State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9004 | NodertInitializeStarted | Adapter-%d, Logical Drive-%d: Initialization Started. | ||
| 1.3.6.1.4.1.3582.1.1.200.9005 | NodertInitializeCompleted | Adapter-%d, Logical Drive-%d: Initialization Completed Successfully. | ||
| 1.3.6.1.4.1.3582.1.1.200.9006 | NodertInitializeAborted | Adapter-%d, Logical Drive-%d: Initialization Aborted by User. | ||
| 1.3.6.1.4.1.3582.1.1.200.9007 | NodertInitializeFailed | Adapter-%d, Logical Drive-%d: Initialization Failed. | ||
| 1.3.6.1.4.1.3582.1.1.200.9008 | NodertCheckConsistencyStarted | Adapter-%d, Logical Drive-%d: Check Consistency Started. | ||
| 1.3.6.1.4.1.3582.1.1.200.9009 | NodertCheckConsistencyCompleted | Adapter-%d, Logical Drive-%d: Check Consistency Completed. No Inconsistencies Found. | ||
| 1.3.6.1.4.1.3582.1.1.200.9010 | NodertCheckConsistencyAborted | Adapter-%d, Logical Drive-%d: Check Consistency Aborted by User. | ||
| 1.3.6.1.4.1.3582.1.1.200.9011 | NodertConsistencyCorrected | Adapter-%d, Logical Drive-%d: Check Consistency Operation Completed. Inconsistencies have been Cured. | ||
| 1.3.6.1.4.1.3582.1.1.200.9012 | NodertCheckConsistencyFailed | Adapter-%d, Logical Drive-%d: Check Consistency Failed. | ||
| 1.3.6.1.4.1.3582.1.1.200.9013 | NodertReconstructionStarted | Adapter-%d, Logical Drive-%d: Reconstruction Started. | ||
| 1.3.6.1.4.1.3582.1.1.200.9014 | NodertReconstructionCompleted | Adapter-%d, Logical Drive-%d: Reconstruction Completed Successfully. | ||
| 1.3.6.1.4.1.3582.1.1.200.9015 | NodertReconstructionFailed | Adapter-%d, Logical Drive-%d: Reconstruction Failed. | ||
| 1.3.6.1.4.1.3582.1.1.200.9016 | NodertPredictiveFailuresExceeded | Adapter-%d, Channel-%d, Target-%d: Reported Predictive Failure. Drive Identification String = %s Sense Key = 0x%x, ASC = 0x%x, ASCQ = 0x%x. | ||
| 1.3.6.1.4.1.3582.1.1.200.9017 | NodertPredictiveFailuresFalse | Adapter-%d, Channel-%d, Target-%d: Reported Failure Prediction Threshold Exceeded [FALSE]. Drive Identification String = %s Sense Key = 0x%x, ASC = 0x%x, ASCQ … | ||
| 1.3.6.1.4.1.3582.1.1.200.9018 | NodertCheckConditionStatus | Adapter-%d, Channel-%d, Target-%d: Command Completed with Sense-Key-0x%x ASC-0x%x ASCQ-0x%x. | ||
| 1.3.6.1.4.1.3582.1.1.200.9019 | NodertNewDriveInserted | Adapter-%d, Channel-%d, Target-%d: New Device Inserted. | ||
| 1.3.6.1.4.1.3582.1.1.200.9020 | NodertBatteryMissing | Adapter-%d: Battery Module is missing. | ||
| 1.3.6.1.4.1.3582.1.1.200.9021 | NodertBatteryVolatageLow | Adapter-%d: Battery Module Voltage is Low. | ||
| 1.3.6.1.4.1.3582.1.1.200.9022 | NodertBatteryTemperatureHigh | Adapter-%d: Battery Module Temperature Exceeded Danger Threshold. | ||
| 1.3.6.1.4.1.3582.1.1.200.9023 | NodertPhysicalDriveStateReady | Adapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9024 | NodertPhysicalDriveStateOnline | Adapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9025 | NodertPhysicalDriveStateFailed | Adapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9026 | NodertPhysicalDriveStateRebuild | Adapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9027 | NodertPhysicalDriveStateHotspare | Adapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9028 | NodertLogicalDriveStateOffline | Adapter-%d, Logical Drive-%d: State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9029 | NodertLogicalDriveStateDegraded | Adapter-%d, Logical Drive-%d: State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9030 | NodertLogicalDriveStateOptimal | Adapter-%d, Logical Drive-%d: State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9031 | NodertLogicalDriveStateInitialize | Adapter-%d, Logical Drive-%d: State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9032 | NodertLogicalDriveStateChkConsist | Adapter-%d, Logical Drive-%d: State Changed from %s to %s. | ||
| 1.3.6.1.4.1.3582.1.1.200.9033 | NodertEnclTemperatureOutofRange | Adapter-%d, Channel-%d, Enclosure-%d, Temperature Sensor -%d: Temperature %d is out of Range | ||
| 1.3.6.1.4.1.3582.1.1.200.9034 | NodertEnclTemperatureNormal | Adapter-%d, Channel-%d, Enclosure-%d, Temperature Sensor -%d: Temperature %d is Normal | ||
| 1.3.6.1.4.1.3582.1.1.200.9035 | NodertEnclFanMalfunction | Adapter-%d, Channel-%d, Enclosure-%d, Fan-%d: Fan is Malfunctioning | ||
| 1.3.6.1.4.1.3582.1.1.200.9036 | NodertEnclFanOk | Adapter-%d, Channel-%d, Enclosure-%d, Fan-%d: Fan is operating properly | ||
| 1.3.6.1.4.1.3582.1.1.200.9037 | NodertEnclPowerSupplyMalfunction | Adapter-%d, Channel-%d, Enclosure-%d, Power Supply-%d: Power Supply is Malfunctioning | ||
| 1.3.6.1.4.1.3582.1.1.200.9038 | NodertEnclPowerSupplyOk | Adapter-%d, Channel-%d, Enclosure-%d, Power Supply-%d: Power Supply is operating properly | ||
| 1.3.6.1.4.1.3582.1.1.200.9040 | NodertFCLooplStateChange | Adapter-%d, LoopId-%d: Loop State Changed from %s to %s. |