RoamAbout-MIB
94 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.36 | Nodedec | |||
| 1.3.6.1.4.1.36.2 | Nodeema | |||
| 1.3.6.1.4.1.36.2.18 | NodedecMIBextension | |||
| 1.3.6.1.4.1.36.2.18.35 | Noderoamabout | |||
| 1.3.6.1.4.1.36.2.18.35.1 | ScalarrabtPCCardType | read-only | mandatory | The type of PC card inserted in the Access Point. |
| 1.3.6.1.4.1.36.2.18.35.2 | ScalarrabtIPAddressState | read-write | mandatory | Determines the state of IP Address storage. A value of 2 causes the current IP address to be stored in NVRAM. |
| 1.3.6.1.4.1.36.2.18.35.3 | ScalarrabtBridgeMode | read-write | mandatory | CURRENT Access Point bridge mode state. LAN-to-LAN mode is the improved name for 802.11. LAN-to-LAN used to be called full-bridge pre-802.11. |
| 1.3.6.1.4.1.36.2.18.35.4 | ScalarrabtUplineDumpMode | read-write | mandatory | Determines whether or not a dump file is created on an Access Point crash. |
| 1.3.6.1.4.1.36.2.18.35.5 | ScalarrabtMemorySize | read-only | mandatory | The size of the memory in the Access Point in Mbytes. |
| 1.3.6.1.4.1.36.2.18.35.6 | ScalarrabtUpgradeFlash | write-only | mandatory | Causes the Access Point to attempt a flash upgrade. Be aware that this causes the Access Point to reset. |
| 1.3.6.1.4.1.36.2.18.35.7 | ScalarrabtForceUplineDump | write-only | mandatory | Causes the Access Point to attempt a upline dump. Be aware that this causes the Access Point to reset. |
| 1.3.6.1.4.1.36.2.18.35.8 | ScalarrabtStationName | read-write | mandatory | The wireless station name sent out as part of the beacon messages. Valid only when a DS card is inserted in the Access Point. |
| 1.3.6.1.4.1.36.2.18.35.9 | ScalarrabtIPSubnetMask | read-write | mandatory | The IP subnet mask for this access Point. |
| 1.3.6.1.4.1.36.2.18.35.10 | ScalarrabtDSChannel | read-write | mandatory | The channel number for the wireless non-IEEE 2400DS card. This value is only valid currently if a 2400DS card is installed. After changing this value, it will … |
| 1.3.6.1.4.1.36.2.18.35.11 | ScalarrabtDSCountryVariant | read-only | mandatory | Describes the country variant of the 2400DS card. This value is only valid currently if a 2400DS card is installed. |
| 1.3.6.1.4.1.36.2.18.35.12 | ScalarrabtDSCurrentNWID | read-only | mandatory | The WaveLAN Network ID (NWID) this RF-modem is currently operating with. |
| 1.3.6.1.4.1.36.2.18.35.13 | ScalarrabtEncryptionEnable | read-write | mandatory | Used to enable or disable encryption of the wireless radio signals if the installed PC Card supports encryption, and the Access Point is in the 'trusted' secur… |
| 1.3.6.1.4.1.36.2.18.35.14 | NoderabtPTPDiag | |||
| 1.3.6.1.4.1.36.2.18.35.14.1 | ScalarrabtPTPRemoteStationMAC | read-write | mandatory | The MAC address for the remote station to participate in the Point-to-Point diagnostic test. To initiate a search for a participating station, write the broadc… |
| 1.3.6.1.4.1.36.2.18.35.14.2 | ScalarrabtPTPRemoteStationName | read-only | mandatory | The wireless station name of the remote station participating in the Point-to-Point diagnostic test. |
| 1.3.6.1.4.1.36.2.18.35.14.3 | ScalarrabtPTPRemoteSignalLevel | read-only | mandatory | The last remote signal level value obtained from the Point-to-Point diagnostic test. A value of 0 is returned if the last sample was not valid. |
| 1.3.6.1.4.1.36.2.18.35.14.4 | ScalarrabtPTPRemoteNoiseLevel | read-only | mandatory | The last remote noise level value obtained from the Point-to-Point diagnostic test. A value of 0 is returned if the last sample was not valid. |
| 1.3.6.1.4.1.36.2.18.35.14.5 | ScalarrabtPTPRemoteSignalQuality | read-only | mandatory | The last remote signal quality value obtained from the Point-to-Point diagnostic test. A value of 0 is returned if the PTP Diagnostic testing is not currently … |
| 1.3.6.1.4.1.36.2.18.35.14.6 | ScalarrabtPTPInterval | read-write | mandatory | Writing a 1 to this variable causes a single PTP sample to be performed. |
| 1.3.6.1.4.1.36.2.18.35.14.7 | ScalarrabtPTPLocalSignalLevel | read-only | mandatory | The last LOCAL Signal Level value obtained from the Point-to-Point diagnostic test. A value of 0 is returned if the last sample was not valid. |
| 1.3.6.1.4.1.36.2.18.35.14.8 | ScalarrabtPTPLocalNoiseLevel | read-only | mandatory | The last LOCAL Noise Level value obtained from the Point-to-Point diagnostic test. A value of 0 is returned if the last sample was not valid. |
| 1.3.6.1.4.1.36.2.18.35.14.9 | ScalarrabtPTPLocalSignalQuality | read-only | mandatory | The last LOCAL signal quality value obtained from the Point-to-Point diagnostic test. A value of 0 is returned if the last sample was not valid. |
| 1.3.6.1.4.1.36.2.18.35.15 | NoderabtDot11 | |||
| 1.3.6.1.4.1.36.2.18.35.15.1 | NoderabtDot11Current | |||
| 1.3.6.1.4.1.36.2.18.35.15.1.1 | ScalarrabtDot11CurrentChannel | read-only | mandatory | The CURRENT channel. |
| 1.3.6.1.4.1.36.2.18.35.15.1.2 | ScalarrabtDot11CurrentNetworkName | read-only | mandatory | The CURRENT network name. |
| 1.3.6.1.4.1.36.2.18.35.15.1.3 | ScalarrabtDot11CurrentStationName | read-only | mandatory | Defines the CURRENT station name of the radio interface, used by client utilities. |
| 1.3.6.1.4.1.36.2.18.35.15.1.4 | ScalarrabtDot11CurrentOperationalRate | read-only | mandatory | This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be … |
| 1.3.6.1.4.1.36.2.18.35.15.1.5 | ScalarrabtDot11CurrentSystemScale | read-only | mandatory | Specifies the CURRENT Access Point density in the ESS. |
| 1.3.6.1.4.1.36.2.18.35.15.1.6 | ScalarrabtDot11CurrentDTIMPeriod | read-only | mandatory | Defines the CURRENT number of beacon intervals between successive DTIMs. |
| 1.3.6.1.4.1.36.2.18.35.15.1.7 | ScalarrabtDot11CurrentFragmentationThreshold | read-only | mandatory | This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its… |
| 1.3.6.1.4.1.36.2.18.35.15.1.8 | ScalarrabtDot11CurrentRTSThreshold | read-only | mandatory | This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed… |
| 1.3.6.1.4.1.36.2.18.35.15.1.9 | ScalarrabtDot11CurrentMulticastPMBuffering | read-only | mandatory | Defines if multicast MAC frames are CURRENTLY buffered for transmission after DTIM. If disabled, MAC frames are immediately placed in the output queue for tran… |
| 1.3.6.1.4.1.36.2.18.35.15.1.10 | ScalarrabtDot11CurrentSecureAccess | read-only | mandatory | When this mode is set to enabled, the AP will only associate with stations that have the same network name as the AP. When this mode is set to disabled, a stat… |
| 1.3.6.1.4.1.36.2.18.35.15.1.11 | ScalarrabtDot11CurrentTransmitRate | read-only | mandatory | This value specifies the transmission rate of the AP. It is implemented when cards that operate faster than the 2Mbit 802.11 standard are inserted. |
| 1.3.6.1.4.1.36.2.18.35.15.1.12 | ScalarrabtDot11CurrentPrivacyInvoked | read-only | mandatory | When this attribute is true, it shall indicate that the AP is currently using the 802.11 WEP mechanism for transmitting frames of type Data. |
| 1.3.6.1.4.1.36.2.18.35.15.1.13 | ScalarrabtDot11CurrentExcludeUnencrypted | read-only | mandatory | This value indicates the current setting of the dot11ExcludeUnencrypted attribute in the AP. |
| 1.3.6.1.4.1.36.2.18.35.15.2 | NoderabtDot11Future | |||
| 1.3.6.1.4.1.36.2.18.35.15.2.1 | ScalarrabtDot11FutureChannel | read-write | mandatory | Defines the FUTURE channel (communication frequency) to be used for creating a BSS. Note that different subsets of channels are valid for different registratio… |
| 1.3.6.1.4.1.36.2.18.35.15.2.2 | ScalarrabtDot11FutureNetworkName | read-write | mandatory | Defines the FUTURE Service Set IDentifier to be used for the BSS. The term future means that a change takes effect after the next reset of the Access Point. Th… |
| 1.3.6.1.4.1.36.2.18.35.15.2.3 | ScalarrabtDot11FutureStationName | read-write | mandatory | Defines the FUTURE station name of the radio interface, used by client utilities. The term future means that a change takes effect after the next reset of the … |
| 1.3.6.1.4.1.36.2.18.35.15.2.4 | ScalarrabtDot11FutureOperationalRate | read-write | mandatory | This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be … |
| 1.3.6.1.4.1.36.2.18.35.15.2.5 | ScalarrabtDot11FutureSystemScale | read-write | mandatory | Specifies the FUTURE Access Point density in the ESS. The term future means that the change takes effect after the next reset of the Access Point. The current … |
| 1.3.6.1.4.1.36.2.18.35.15.2.6 | ScalarrabtDot11FutureDTIMPeriod | read-write | mandatory | Defines the FUTURE number of beacon intervals between successive DTIMs. The term future means that a change takes effect after the next reset of the Access Poi… |
| 1.3.6.1.4.1.36.2.18.35.15.2.7 | ScalarrabtDot11FutureFragmentationThreshold | read-write | mandatory | This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its… |
| 1.3.6.1.4.1.36.2.18.35.15.2.8 | ScalarrabtDot11FutureRTSThreshold | read-write | mandatory | This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed… |
| 1.3.6.1.4.1.36.2.18.35.15.2.9 | ScalarrabtDot11FutureMulticastPMBuffering | read-write | mandatory | Defines if multicast MAC frames are to be buffered for transmission after DTIM in the FUTURE. If disabled, MAC frames will be immediately placed in the output … |
| 1.3.6.1.4.1.36.2.18.35.15.2.10 | ScalarrabtDot11FutureSecureAccess | read-write | mandatory | When this mode is set to enabled, the AP will only associate with stations that have the same network name as the AP. When this mode is set to disabled, a stat… |
| 1.3.6.1.4.1.36.2.18.35.15.2.11 | ScalarrabtDot11FutureTransmitRate | read-write | mandatory | This value specifies the transmission rate of the AP. It is implemented when cards that operate faster than the 2Mbit 802.11 standard are inserted. |
| 1.3.6.1.4.1.36.2.18.35.15.2.12 | ScalarrabtDot11FuturePrivacyInvoked | read-write | mandatory | This value specifies the future setting of the dot11PrivacyInvoked attribute in the AP. |
| 1.3.6.1.4.1.36.2.18.35.15.2.13 | ScalarrabtDot11FutureExcludeUnencrypted | read-write | mandatory | This value specifies the future value of the dot11ExcludeUnencrypted attribute in the AP. |
| 1.3.6.1.4.1.36.2.18.35.15.3 | NoderabtDot11General | |||
| 1.3.6.1.4.1.36.2.18.35.15.3.1 | ScalarrabtDot11PCCardVersions | read-only | mandatory | Specifies the version identifiers for the PC card. |
| 1.3.6.1.4.1.36.2.18.35.15.4 | NoderabtDot11Bldg | |||
| 1.3.6.1.4.1.36.2.18.35.15.4.1 | ScalarrabtDot11BldgRemoteMAC | read-only | mandatory | The CURRENT MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.2 | ScalarrabtDot11FutureBldgRemoteMAC | read-write | mandatory | The FUTURE MAC address for the remote station participating in a 802.11 Building-to-Building link. Setting this MAC address and then ISSUING A RESET places the… |
| 1.3.6.1.4.1.36.2.18.35.15.4.3 | ScalarrabtFutureBridgeMode | read-write | mandatory | FUTURE Access Point bridge mode state. LAN-to-LAN mode is the improved name for 802.11. LAN-to-LAN used to be called full-bridge pre-802.11. pre-802.11 was dyn… |
| 1.3.6.1.4.1.36.2.18.35.15.4.4 | NoderabtDot11BldgExt | |||
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1 | NoderabtDot11BldgExtCurrent | |||
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1.1 | ScalarrabtDot11BldgRelayMode | read-write | mandatory | Enabling relay mode allows the Access Point in a point to multi-point configuration to relay broadcast messages to other wireless AP's. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1.2 | ScalarrabtDot11BldgRemoteMAC2 | read-only | mandatory | The CURRENT MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1.3 | ScalarrabtDot11BldgRemoteMAC3 | read-only | mandatory | The CURRENT MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1.4 | ScalarrabtDot11BldgRemoteMAC4 | read-only | mandatory | The CURRENT MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1.5 | ScalarrabtDot11BldgRemoteMAC5 | read-only | mandatory | The CURRENT MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.1.6 | ScalarrabtDot11BldgRemoteMAC6 | read-only | mandatory | The CURRENT MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2 | NoderabtDot11BldgExtFuture | |||
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2.1 | ScalarrabtDot11BldgFutureRelayMode | read-write | mandatory | Enabling relay mode allows the Access Point in a point to multi-point configuration to relay broadcast messages to other wireless AP's. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2.2 | ScalarrabtDot11BldgFutureRemoteMAC2 | read-write | mandatory | The FUTURE MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2.3 | ScalarrabtDot11BldgFutureRemoteMAC3 | read-write | mandatory | The FUTURE MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2.4 | ScalarrabtDot11BldgFutureRemoteMAC4 | read-write | mandatory | The FUTURE MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2.5 | ScalarrabtDot11BldgFutureRemoteMAC5 | read-write | mandatory | The FUTURE MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.4.4.2.6 | ScalarrabtDot11BldgFutureRemoteMAC6 | read-write | mandatory | The FUTURE MAC address for the remote station participating in a 802.11 Building-to-Building link. |
| 1.3.6.1.4.1.36.2.18.35.15.5 | NoderabtDot11WEP | |||
| 1.3.6.1.4.1.36.2.18.35.15.5.1 | ScalarrabtDot11WEPEnhancedImplemented | read-only | mandatory | This value indicates whether the AP is capable of Enhanced Wireless Equivalent Privacy (WEP), using 128-bit keys. |
| 1.3.6.1.4.1.36.2.18.35.15.5.2 | ScalarrabtDot11WEPExcludeSNMP | read-only | mandatory | This value indicates that SNMP management of WEP attributes is disabled in the AP. |
| 1.3.6.1.4.1.36.2.18.35.15.5.3 | Tablerabtdot11KeyStateTable | not-accessible | mandatory | A conceptual table containing a set of booleans identifying if an encryption key has been set or not. |
| 1.3.6.1.4.1.36.2.18.35.15.5.3.1 | Rowrabtdot11KeyStateEntry | not-accessible | mandatory | An Entry (conceptual row) in the Key State Table. ifIndex - Each 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed… |
| 1.3.6.1.4.1.36.2.18.35.15.5.3.1.1 | Columnrabtdot11KeyStateIndex | not-accessible | mandatory | The auxiliary variable used to identify instances of the columnar objects in the Key State Table. |
| 1.3.6.1.4.1.36.2.18.35.15.5.3.1.2 | ColumnrabtDot11KeyState | read-only | mandatory | The state column used for determining if an encryption key is set or not. |
| 1.3.6.1.4.1.36.2.18.35.16 | NoderoamaboutLoader | |||
| 1.3.6.1.4.1.36.2.18.35.16.1 | ScalarrabtFirmwareUseBootp | read-write | mandatory | Controls where the AccessPoint gets the information that it needs to download new firmware. When true(1), indicates that the AP should use the BootP protocol t… |
| 1.3.6.1.4.1.36.2.18.35.16.2 | ScalarrabtFirmwareServerIP | read-write | mandatory | The IP address of the TFTP server that should be used for firmware downloads. This value will be ignored when 'rabtFirmwareUseBootp' is 'false(2)'. |
| 1.3.6.1.4.1.36.2.18.35.16.3 | ScalarrabtFirmwareFilename | read-write | mandatory | The name of the remote file that contains the firmware to be downloaded. This value will be ignored when 'rabtFirmwareUseBootp' is 'false(2)'. |
| 1.3.6.1.4.1.36.2.18.35.16.4 | ScalarrabtFirmwareStatus | read-only | mandatory | Indicates the success or failure of the AccessPoint's most recent attempt to download new firmware. In the case of a failure, the value of this object may prov… |
| 1.3.6.1.4.1.36.2.18.35.16.5 | ScalarrabtCrashUploadUseBootp | read-write | mandatory | Controls where the AccessPoint gets the information that it needs to upload crash dumps. When true(1), indicates that the AP should use the BootP protocol to a… |
| 1.3.6.1.4.1.36.2.18.35.16.6 | ScalarrabtCrashUploadServerIP | read-write | mandatory | The IP address of the TFTP server that should be used for crash dump uploads. This value will be ignored when 'rabtCrashUploadUseBootp' is 'false(2)'. |
| 1.3.6.1.4.1.36.2.18.35.16.7 | ScalarrabtCrashUploadDirectory | read-write | mandatory | The name of the remote directory to which all crash dumps should be uploaded. This value will be ignored when 'rabtCrashUploadUseBootp' is 'false(2)'. |
| 1.3.6.1.4.1.36.2.18.35.17 | NoderoamaboutConsole | |||
| 1.3.6.1.4.1.36.2.18.35.17.1 | ScalarrabtUseConsolePassword | read-write | mandatory |