SCTE-HMS-HE-RF-SWITCH-MIB
34 objects
Change Log: 1. Added Unsigned32 and Integer32 to IMPORTS 2. Removed TEXTUAL-CONVENTION from IMPORTS 3. Corrected 4 digit date code defined in RFC2578 4. heRFSwitchWaitToRestoreTime is changed to Integer32 instead of INTEGER 5. Corrected object type definition in HeRFSwitchInputEntry sequence 6. Added double quote at the end of heRFSwitchInputExternalControl description 7. Changed Rf to RF 8. Changed OID number of heRFSwitchMIBCompliances to 1 instead of 2 9. Changed the text description of SNMPv2 to SNMP for heRFSwitchBasicCompliance MODULE-COMPLIANCE
Imported Objects
| ENTITY-MIB | entPhysicalIndex |
| SCTE-HMS-HE-RF-MIB | heRFSwitchGroup |
| SCTE-HMS-HEADENDIDENT-MIB | HeFaultStatus HeOnOffControl HeTenthdB HeTenthdBm HeTenthdBmV |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5591.1.11.4.2.1 | IdentityheRFSwitchMIB | Change Log: 1. Added Unsigned32 and Integer32 to IMPORTS 2. Removed TEXTUAL-CONVENTION from IMPORTS 3. Corrected 4 digit date code defined in RFC2578 4. heRFSw… | ||
| 1.3.6.1.4.1.5591.1.11.4.2.1.1 | NodeheRFSwitchMIBObjects | |||
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1 | TableheRFSwitchUnitTable | not-accessible | current | A table containing information about RF Switch used in an indoor environment. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1 | RowheRFSwitchUnitEntry | not-accessible | current | List of information about each RF switch. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.1 | ColumnheRFSwitchMode | read-write | current | This controls and/or reports the switching mode. If automatic(1), the RF switch will evaluate the RF input status and make the decision to affect the switch st… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.2 | ColumnheRFSwitchControl | read-write | current | Sets the intended state of the RF Switch. The effect of this control will depend on the value of heRFSwitchMode. If heRFSwitchMode is set to automatic, the val… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.3 | ColumnheRFSwitchRevertEnable | read-write | current | This controls the use of revert switching. If set to on, the switch will attempt to go back to the preferred settings indicated by heRFSwitchControl if heRFSwi… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.4 | ColumnheRFSwitchState | read-only | current | Reports the state of the RF Switch. Not all enumerations must be supported. For example, an A-B RF switch may support only the pathA and pathB enumerations whi… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.5 | ColumnheRFSwitchFailoverStatus | read-only | current | The integral status of both inputs. A value is fault(2), if current switch state heRFSwitchState is different than the preferred setting heRFSwitchControl, oth… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.6 | ColumnheRFSwitchBothInputStatus | read-only | current | The integral status of both inputs. A value is fault(2), if both input levels are below the nominal value; otherwise, it is normal(1). This object must provide… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.7 | ColumnheRFSwitchHysteresis | read-write | current | Controls switch input hysteresis amount. The amount of hysteresis used and the ability to change it is to be determined by the vendor. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.8 | ColumnheRFSwitchWaitToRestoreTime | read-write | current | Controls hysteresis time in sec. If in automatic switching mode and revert mode is enabled, a switch back to the original side will be delayed for the time spe… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.9 | ColumnheRFSwitchSensorMode | read-write | current | Controls what source will be used for determining input status: A value of internal(1) causes the internal RF detection circuitry to be used. A value of extern… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2 | TableheRFSwitchInputTable | not-accessible | current | A table containing information about each RF Switch input used in an indoor environment. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1 | RowheRFSwitchInputEntry | not-accessible | current | List of information about each RF switch input. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.1 | ColumnheRFSwitchInputIndex | not-accessible | current | Index number corresponding to the RF Input. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.2 | ColumnheRFSwitchInputRFLevel | read-only | current | The measured RF input power for the RF switch. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.3 | ColumnheRFSwitchSetInputPowerThreshold | read-write | current | Input power switchover point for this input. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.4 | ColumnheRFSwitchInputStatus | read-only | current | The integral status of the input. A value is fault(2), if the input levels are not in the nominal range; otherwise, it is normal(1). This object must provide f… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.5 | ColumnheRFSwitchInputDescription | read-only | current | A description of the switch input port. The description text is to be determined by the equipment manufacturer. For example, Input A or Side B. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.6 | ColumnheRFSwitchInputExternalControl | read-only | current | This is an external control signal that indicates the status of the associated input. A value is fault(2), if the external control signal level is not in the n… |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.3 | TableheRFSwitchOutputTable | not-accessible | current | A table containing information about each RF Switch output used in an indoor environment. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.3.1 | RowheRFSwitchOutputEntry | not-accessible | current | List of information about each RF switch output. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.3.1.1 | ColumnheRFSwitchOutputIndex | not-accessible | current | Index number corresponding to the RF Output. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.1.3.1.2 | ColumnheRFSwitchOutputDescription | read-only | current | A description of the switch output port. The description text is to be determined by the equipment manufacturer. For example, Output A or Seconday Output. |
| 1.3.6.1.4.1.5591.1.11.4.2.1.2 | NodeheRFSwitchMIBConformance | |||
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.1 | NodeheRFSwitchMIBCompliances | |||
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.1.1 | ComplianceheRFSwitchBasicCompliance | current | The compliance statement for SNMP HMS Headend RF Switch entities which implement the SNMP heRFSwitchMIB. | |
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.2 | NodeheRFSwitchMIBGroups | |||
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.2.1 | GroupheRFSwitchUnitMandatoryGroup | current | The main group defines heRFSwitchUnitTable objects which are mandatory to all indoor RF switch modules. | |
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.2.2 | GroupheRFSwitchInputMandatoryGroup | current | The main group defines heRFSwitchInputTable objects which are mandatory to all indoor RF switch modules. | |
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.2.3 | GroupheRFSwitchOutputMandatoryGroup | current | The main group defines heRFSwitchOutputTable objects which are mandatory to all indoor RF switch modules. | |
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.2.4 | GroupheRFSwitchUnitGroup | current | The collection of heRFSwitchUnitTable objects which are used to represent the indoor RF switch module. | |
| 1.3.6.1.4.1.5591.1.11.4.2.1.2.2.5 | GroupheRFSwitchInputGroup | current | The collection of heRFSwitchInputTable objects which are used to represent the indoor RF switch module. |