SCTE-HMS-HEADENDIDENT-TC-MIB
25 objects
The MIB module is for representing general information about HeadEnd Digital equipment present(or indoor) and is supported by an SNMP agent.
Imported Objects
| SNMPv2-SMI | enterprises Integer32 MODULE-IDENTITY Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5591.1.11.5.1 | IdentityhmsTextualConventionMIB | The MIB module is for representing general information about HeadEnd Digital equipment present(or indoor) and is supported by an SNMP agent. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DeviceEnableDisableValues | INTEGER { disabled (1), enabled (2), notSupported(3) } | current | This data type represents whether the object is disabled(1) or enabled(2), or the object is not supported (3) by the current configuration or this device's hardware. |
| HeAlarmControl | INTEGER { alarmEnabled(1), alarmDisabled(2) } | current | Alarm Control value for a specific device. This object is used to control sending traps related to this headend entity or enabling disabling of raising an alarm condition for a specific entity. |
| HeClockSource | INTEGER { unknown(1), other(2), internal(3), external(4), ntp(5), none(6) } | current | An enumerated value that provides the location where the value for the clock on the module is coming from. internal - this value is being derived internally from the local module timing source. external - an source that… |
| HeDigitalAlarmSeverity | INTEGER { critical(1), major(2), minor(3), warning(4), status(5), clear(6), information(7) } | current | The alarm severity that is determined by the device and sent over in the trap message. |
| HeDigitalAlarmType | INTEGER { communication(1), process(2), session(3), capacity(4), maintenance(5), provisioning(6), programMgmt(7), redundancy(8), other(9) } | current | The alarm type that describes the Event that caused the alarm. |
| HeFaultStatus | INTEGER { normal(1), fault(2) } | current | An enumerated value that provides a fault status of a particular hardware or software parameter that usually represent some sort of condition. A value normal(1) indicates the normal condition. A value fault(2) indicates… |
| HeHundredthNanoMeter | Unsigned32 | current | This data type represents wavelength values that are normally expressed in nano meters. Units are in hundredths of a NanoMeter; for example, 1550.56 nm will be represented as 155056. |
| HeHundredthWatts | Unsigned32 | current | This data type represents power values that are normally expressed in watts. Units are in hundredths of a watt; for example, 420 watts will be represented as 42000. |
| HeMilliAmp | Unsigned32 | current | This data type represents current levels that are normally expressed in amperes. Units are in milliamperes; for example, 2.1 Amperes would be expressed as 2100. |
| HeOnOffControl | INTEGER { off(1), on(2), meaningless(3) } | current | An enumerated value that provides a control of a particular hardware or software parameter that usually represent some sort of switch. A SET request with a value off(1) will cause the switch to be shut off. A SET reques… |
| HeOnOffStatus | INTEGER { off(1), on(2) } | current | An enumerated value that provides a status of a particular hardware or software parameter that usually represent some sort of switch. A value off(1) indicates the switch is off. A value on(2) indicates the switch is on. |
| HePIDValue | Unsigned32 (0..8191 | 65535) | current | This data type represents a packet identifier (PID) value which ranges from 0 to (2^13 - 1). The value of 65535 indicates that either the PID is invalid or does not exist. |
| HeResetValue | INTEGER { reset(1), running(2), resetting(3) } | current | Configured reset value for a specific device. reset - the value of reset is SET at the device and the device will reset. running - the normal value of the device is running when an SNMP GET of the reset value is sent. r… |
| HeTenthCentigrade | Integer32 | current | This data type represents temperature values that are normally expressed in Centigrade. Units are in tenths of a Centigrade; for example, -5.1 Centigrade will be represented as -51. |
| HeTenthdB | Integer32 | current | This data type represents power levels that are normally expressed in dB. Units are in tenths of a dB; for example, -5.1 dB will be represented as -51. |
| HeTenthdBm | Integer32 | current | This data type represents power levels that are normally expressed in dBm. Units are in tenths of a dBm; for example, -5.1 dBm will be represented as -51. |
| HeTenthdBmV | Integer32 | current | This data type represents power levels that are normally expressed in dBmV. Units are in tenths of a dBmV; for example, -5.1 dBmV will be represented as -51. |
| HeTenthVolt | Integer32 | current | This data type represents voltage levels that are normally expressed in volts. Units are in tenths of a volt; for example, -48.1 volts will be represented as -481. |
| HeTrapRegenerate | INTEGER { trapRegenerate(1), trapNormal(2) } | current | This value tells the SNMP Agent to send the Trap Regenerate Trap for all values of Current alarms for this entity. The device can provide for a means to send ALL current alarms, not just one specific entity. |
| MpegErrorStatus | INTEGER { good (1), errors (2), notSupported(3) } | current | This data type represents whether the object is good(1) or has errors(2), or the object is not supported (3) by the current configuration or this device's hardware. |
| ProgDataType | INTEGER { video (1), audio (2), data (3), other(4) } | current | This value defines the types of data that can be contained in Programs and program streams. |
| QAMChannelInterleaveMode | INTEGER { unknown(1), other(2), fecI8J16(3), fecI16J8(4), fecI32J4(5), fecI64J2(6), fecI128J1(7), fecI12J17(8), fecI128J2(9), fecI128J3(10), fecI128J4(11), fecI128J5(12), fecI128J6(13), fecI128J7(14), fecI128J8(15) } | current | This value defines the types of QAM Interleave Mode which follows the value of docsIfDownChannelInterleave. This value is supported by HMS QAM devices. |
| QAMChannelModulationFormat | INTEGER { unknown(1), other(2), qam64(3), qam256(4), qam128(5), qam512 (6), qam1024 (7) } | current | This value defines the types of QAM Channel Modulation that is supported by QAM devices. |
| VideoInputFrameRateType | INTEGER { other (1), autoSelect (2), f24Hz (3), f25Hz (4), f29Hz97 (5), f30Hz (6), f29or30Hz (7), f48Hz (8), f50Hz (9), f59Hz94 (10), f60Hz (11), f59or60Hz (12) } | current | This value defines the types of MPEG Video Input Frame Rate that is supported by QAM devices. |