STN-ATM-MIB
238 objects
Initial version of this MIB module.
Imported Objects
| IF-MIB | InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION TruthValue |
| SPRING-TIDE-NETWORKS-SMI | stnNotification stnSystems |
| SPRING-TIDE-NETWORKS-TC | NSAPAddress |
| STN-ROUTER-MIB | stnRouterIndex |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3551.2.6 | IdentitystnAtm | Initial version of this MIB module. | ||
| 1.3.6.1.4.1.3551.2.6.1 | NodestnAtmObjects | |||
| 1.3.6.1.4.1.3551.2.6.1.1 | NodestnAtmLinks | |||
| 1.3.6.1.4.1.3551.2.6.1.1.1 | NodestnVcLinks | |||
| 1.3.6.1.4.1.3551.2.6.1.1.1.1 | TablestnVcLinkTable | not-accessible | current | A list of VC Link entries. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1 | RowstnVcLinkEntry | not-accessible | current | Entry contains information about a particular VC link. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.1 | ColumnstnVcLinkIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.2 | ColumnstnVcLinkVpi | read-only | current | The VPI value of the VPL. Note that the VPI=0 is not used for a VPL not associated with a VCL. The maximum VPI value cannot exceed the value allowable by the a… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.3 | ColumnstnVcLinkVci | read-only | current | The VCI value of the VCL. The maximum VCI value cannot exceed the value allowable by the atmInterfaceMaxVciBits. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.4 | ColumnstnVcLinkRcvTrafDescr | read-only | current | Receive traffic descriptor identifier for this VPL. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.5 | ColumnstnVcLinkXmtTrafDescr | read-only | current | Transmit traffic descriptor identifier for this VPL. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.6 | ColumnstnVcLinkAalObjectsValid | read-only | current | Indicates whether the following AAL objects are valid (whether the local VCL end-point is also the VCC end-point). Transmit traffic descriptor identifier for t… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.7 | ColumnstnVcLinkAalType | read-only | current | An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL is in use. The type of AAL used on this VCC. The AAL typ… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.8 | ColumnstnVcLinkAal5XmtSDUSize | read-only | current | An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDUsize in octets that… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.9 | ColumnstnVcLinkAal5RcvSDUSize | read-only | current | An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets tha… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.10 | ColumnstnVcLinkAal5EncapsType | read-only | current | An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.11 | ColumnstnVcLinkCastType | read-only | current | The type of topology of a connection (point- to-point, point-to-multipoint). In the case of point-to-multipoint, the orientation of this VPL in the connection.… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.12 | ColumnstnVcLinkConnKind | read-only | current | The use of call control. An spvcInitiator is always cross-connected to an svcOutgoing, and an spvcTarget is always cross-connected to an svcIncoming. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.13 | ColumnstnVcLinkAccEnabled | read-only | current | ATM accounting is enabled for this VC Link. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.14 | ColumnstnVcLinkOAMMgmtEnabled | read-only | current | OAM management is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.15 | ColumnstnVcLinkOAMXmtFrequency | read-only | current | Number of seconds between transmitting OAM loopback cells. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.16 | ColumnstnVcLinkOAMRetryUpCount | read-only | current | Number of consecutive end-to-end F5 OAM loopback cell responses that must be received in order to change a PVC state to up. Does not apply to SVCs. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.17 | ColumnstnVcLinkOAMRetryDownCount | read-only | current | Number of consecutive end-to-end F5 OAM loopback cell responses that are not received in order to change a PVC state to down or tear down an SVC. |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.18 | ColumnstnVcLinkOAMRetryFrequency | read-only | current | The frequency (in seconds) that end-to-end F5 loopback cells should be transmitted when a change in UP/DOWN state is being verified. For example, if a PVC is u… |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.19 | ColumnstnVcLinkPppId | read-only | current | PPP ID |
| 1.3.6.1.4.1.3551.2.6.1.1.1.1.1.20 | ColumnstnVcLinkOperStatus | read-only | current | Operational status of the VC Link. |
| 1.3.6.1.4.1.3551.2.6.1.2 | NodestnAtmCrossConns | |||
| 1.3.6.1.4.1.3551.2.6.1.2.1 | NodestnVcCrossConns | |||
| 1.3.6.1.4.1.3551.2.6.1.2.1.1 | TablestnVcCrossConnTable | not-accessible | current | A list of VC cross connection entries. |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1 | RowstnVcCrossConnEntry | not-accessible | current | Entry contains information about a particular VC cross connection. |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.1 | ColumnstnVcCrossConnLowIfIndex | read-only | current | The value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VP cross-connect. The term low implies that this ATM interface h… |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.2 | ColumnstnVcCrossConnLowVpi | read-only | current | The value of this object is equal to the VPI value at the ATM interface associated with the VP cross-connect that is identified by LowIfIndex. The VPI value ca… |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.3 | ColumnstnVcCrossConnLowVci | read-only | current | The value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by LowIfIndex. The VCI value ca… |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.4 | ColumnstnVcCrossConnHighIfIndex | read-only | current | The value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VP cross-connect. The term low implies that this ATM interface h… |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.5 | ColumnstnVcCrossConnHighVpi | read-only | current | The value of this object is equal to the VPI value at the ATM interface associated with the VP cross-connect that is identified by LowIfIndex. The VPI value ca… |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.6 | ColumnstnVcCrossConnHighVci | read-only | current | The value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by LowIfIndex. The VCI value ca… |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.7 | ColumnstnVcCrossConnLowAutoAssign | read-only | current | Controls low vpi/vci/ifIndex auto assignement to an ECF. If set to true MSM will attempt to dynamically auto assign the connection to an available ECF. |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.8 | ColumnstnVcCrossConnHighAutoAssign | read-only | current | Controls high vpi/vci/ifIndex auto assignement to an ECF. If set to true MSM will attempt to dynamically auto assign the connection to an available ECF. |
| 1.3.6.1.4.1.3551.2.6.1.2.1.1.1.9 | ColumnstnVcCrossConnOperStatus | read-only | current | Operational status of the VC cross connection. |
| 1.3.6.1.4.1.3551.2.6.1.2.2 | NodestnVpCrossConns | |||
| 1.3.6.1.4.1.3551.2.6.1.3 | NodestnAtmTrafficDescrs | |||
| 1.3.6.1.4.1.3551.2.6.1.3.1 | TablestnTrafficDescrTable | not-accessible | current | A list of ATM traffic descriptor entries. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1 | RowstnTrafficDescrEntry | not-accessible | current | Entry contains information about a particular ATM traffic descriptor. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.1 | ColumnstnTrafDescrIndex | read-only | current | The value of this object identifies the row in the stnTrafficDescrTable. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.2 | ColumnstnTrafDescrName | read-only | current | Text name assigned to this traffic descriptor. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.3 | ColumnstnTrafDescrType | read-only | current | The value of this object identifies the type of ATM traffic descriptor. The type may indicate no traffic descriptor or traffic descriptor with one or more para… |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.4 | ColumnstnTrafDescrParam1 | read-only | current | The first parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.5 | ColumnstnTrafDescrParam2 | read-only | current | The second parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.6 | ColumnstnTrafDescrParam3 | read-only | current | The third parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.7 | ColumnstnTrafDescrParam4 | read-only | current | The fourth parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.8 | ColumnstnTrafDescrParam5 | read-only | current | The fifth parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.9 | ColumnstnTrafDescrQosClass | read-only | current | The value of this object identifies the QoS Class. Four Service classes have been specified in the ATM Forum UNI Specification: Service Class A: Constant bit r… |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.10 | ColumnstnTrafDescrServiceCategory | read-only | current | The ATM service category. Service categories are as follows: other, cbr, rt-vbr, nrt-vbr, abr, ubr |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.11 | ColumnstnTrafDescrFrameDiscard | read-only | current | Whether the network should discard frames rather than cells. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.12 | ColumnstnTrafDescrOperStatus | read-only | current | Operational status of the traffic descriptor. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.13 | ColumnstnTrafDescrCommittedRate | read-only | current | The traffic rate in bits per second that the network is committed to transmit for VCs using this transmit traffic descriptor. |
| 1.3.6.1.4.1.3551.2.6.1.3.1.1.14 | ColumnstnTrafDescrMaximumRate | read-only | current | The maximum traffic rate in bits per second that the network will transmit for VCs using this transmit traffic descriptor, if it differs from the committed rat… |
| 1.3.6.1.4.1.3551.2.6.1.4 | NodestnAtmPorts | |||
| 1.3.6.1.4.1.3551.2.6.1.4.1 | NodestnAtmPortAttrs | |||
| 1.3.6.1.4.1.3551.2.6.1.4.1.1 | TablestnAtmPortAttrTable | not-accessible | current | A list of ATM port attribute entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1 | RowstnAtmPortAttrEntry | not-accessible | current | Entry contains information about a particular ATM port attribute entry. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.1 | ColumnstnAtmPortIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.2 | ColumnstnAtmPortIfType | read-only | current | The interface type of the connection point to the switch fabric. Values are: sonet(1), enet(2), epif(3), rim-enet(4). |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.3 | ColumnstnAtmPortIfState | read-only | current | The interface state of the connection point to the switch fabric. Values are: not-present(0), detected(1), configured(2), up-non-redundant(3), up-redundant(4),… |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.4 | ColumnstnAtmPortEnabled | read-only | current | Whether the ATM port is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.5 | ColumnstnAtmPortMinVccVpi | read-only | current | Minimum VPI used for Virtual Channel Circuits. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.6 | ColumnstnAtmPortMaxVccVpi | read-only | current | Maximum VPI used for Virtual Channel Circuits. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.7 | ColumnstnAtmPortMinVccVci | read-only | current | Minimum VCI used for Virtual Channel Circuits. To avoid clashes with the reserved ATM VCI values (such as 5 for signaling and any other reserved values includi… |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.8 | ColumnstnAtmPortMaxVccVci | read-only | current | Maximum VCI used for Virtual Channel Circuits. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.9 | ColumnstnAtmPortMinVpcVpi | read-only | current | Minimum VPI used for Virtual Path Circuits. To avoid clashes with the reserved ATM VCCs values (such as 5 for signaling and any other reserved values including… |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.10 | ColumnstnAtmPortMaxVpcVpi | read-only | current | Maximum VCI used for Virtual Channel Circuits. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.11 | ColumnstnAtmPortMaxActivePaths | read-only | current | The maximum number of active paths that can be active at any time on this port. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.12 | ColumnstnAtmPortMaxActiveChannels | read-only | current | The maximum number of virtual channels that can be active at any time on this port. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.13 | ColumnstnAtmPortPVCAddress | read-only | current | The default configured PVC address information (20-byte NSAP address). |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.14 | ColumnstnAtmPortSVCAddress | read-only | current | The default configured SVC address information (20-byte NSAP address). |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.15 | ColumnstnAtmPortSigVpi | read-only | current | The VPI used for the signaling channel. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.16 | ColumnstnAtmPortSigVci | read-only | current | The VCI used for the signaling channel. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.17 | ColumnstnAtmPortSigEnabled | read-only | current | Indicates if port will have a signaling stack. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.18 | ColumnstnAtmPortIlmiVpi | read-only | current | The VPI used for ILMI channel. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.19 | ColumnstnAtmPortIlmiVci | read-only | current | The VCI used for ILMI channel. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.20 | ColumnstnAtmPortIlmiEnabled | read-only | current | Indicates if port will use ILMI. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.21 | ColumnstnAtmPortOamManagementEnabled | read-only | current | Indicates if port is using OAM Management Procedures. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.22 | ColumnstnAtmPortOamXmtFrequency | read-only | current | Indicates Frequency of OAM Transmit Cells. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.23 | ColumnstnAtmPortOamRetryUpCount | read-only | current | Indicates OAM Cell Retry Up Count value. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.24 | ColumnstnAtmPortOamRetryDownCount | read-only | current | Indicates OAM Cell Retry Down Count value. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.25 | ColumnstnAtmPortOamRetryFrequency | read-only | current | Indicates OAM Retry Frequency value. |
| 1.3.6.1.4.1.3551.2.6.1.4.1.1.1.26 | ColumnstnAtmPortOperStatus | read-only | current | Operational status of the Port. |
| 1.3.6.1.4.1.3551.2.6.1.4.2 | NodestnAtmPortIlmi | |||
| 1.3.6.1.4.1.3551.2.6.1.4.2.1 | TablestnAtmPortIlmiTable | not-accessible | current | A list of ATM ILMI Port entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1 | RowstnAtmPortIlmiEntry | not-accessible | current | Entry contains information about a particular ATM Port ILMI entry. |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.1 | ColumnstnAtmPortIlmiIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.2 | ColumnstnAtmPortIlmiVersion | read-only | current | Specifies the signaling stack protocol type to be used on this port. Valid options are: uni-3-dot-0 uni-3-dot-1 uni-4-dot-0 iisp-3-dot-1 |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.3 | ColumnstnAtmPortIlmiNetworkOrientation | read-only | current | Specifies the ATM device type. Valid options are: user, network |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.4 | ColumnstnAtmPortIlmiAutoNegotiate | read-only | current | Indicates ILMI auto negotiation mode |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.5 | ColumnstnAtmPortIlmiPollInterval | read-only | current | ILMI connection poll interval (S) in seconds. When DC-ILMI is transmitting SNMP Get messages during the attempt to establish connectivity with the remote ILMI … |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.6 | ColumnstnAtmPortIlmiCheckConnectionInt | read-only | current | ILMI check connection poll interval (T) in seconds. If connectivity checking is enabled (as spec by the value connect in the Admin_Status parameter below), thi… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.7 | ColumnstnAtmPortIlmiInactivityFactor | read-only | current | ILMI inactivity factor (K). The number of consecutive polls for which no response is received from the remote ILMI component before ILMI connectivity is assume… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.8 | ColumnstnAtmPortIlmiLocalConn | read-only | current | Specifies whether the local end of the ILMI connection is advertised as a 'public' or 'private' ILMI device. Values are: other, public, private |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.9 | ColumnstnAtmPortIlmiAdminStatus | read-only | current | Specifies which functions of DC-ILMI are enabled. The value std-ilmi must be specified; this value may be combined (using a bitwise OR) with one or more of the… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.10 | ColumnstnAtmPortIlmiEnterprise | read-only | current | Enterprise Object ID that DC-ILMI will use in building SNMP traps (or other generic MIB traps). This parameter can be used to identify the originator of the tr… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.11 | ColumnstnAtmPortIlmiLocalOid | read-only | current | Object ID identifying the local machine - the first 4 octets indicate the length of the object id. For example, the null object id (0.0), which should be used … |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.12 | ColumnstnAtmPortIlmiNetPrefix | read-only | current | Default network prefix. If the prefix length is non-zero, ILMI creates an entry in the ILMI NetPrefix Table for this prefix; otherwise the Net_Prefix parameter… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.13 | ColumnstnAtmPortIlmiPrefixLen | read-only | current | The length of the default network prefix |
| 1.3.6.1.4.1.3551.2.6.1.4.3 | NodestnAtmPortSignaling | |||
| 1.3.6.1.4.1.3551.2.6.1.4.3.1 | NodestnAtmPortSigs | |||
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1 | TablestnAtmPortSigTable | not-accessible | current | A list of ATM port signal entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1 | RowstnAtmPortSigEntry | not-accessible | current | Entry contains information about a particular ATM port signal entry. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.1 | ColumnstnAtmPortSigIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.2 | ColumnstnAtmPortSigVersion | read-only | current | Specifies the signaling stack protocol type to be used on this port. Valid options are: UNI 3.0, UNI 3.1, IISP 3.1, PNNI 1.0 |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.3 | ColumnstnAtmPortSigNetworkOrientation | read-only | current | Indicates whether the ATM device is of the user or network type. Valid values are: user, network |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.4 | ColumnstnAtmPortSigAssignVpiVci | not-accessible | current | Specifies whether VPI/VCI assignment is the responsibility of the local signaling stack or of its partner stack. This parameter is used only for UNI 4.0. Value… |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.5 | ColumnstnAtmPortSigVpSigType | read-only | current | Specifies whether this signaling stack performs VP associated signaling: Valid options are: associated-signaling explicit-vpci |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.6 | ColumnstnAtmPortSigParseMode | read-only | current | Specifies whether the message parser component of Sig should perform validity checking on the contents of received IEs. This element resides in the CCS MIB to … |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.7 | ColumnstnAtmPortSigPrefCarrierPresent | read-only | current | Specifies whether a default prefrd carrier (transit network) is defined. Valid options are: true - the Default_Network_Id below defines which carr is the prefe… |
| 1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.8 | ColumnstnAtmPortSigPrefCarrier | read-only | current | Specifies the default preferred carrier. If stnAtmPortIlmiPrefCarrierPresent is set to false, this element is not used. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2 | NodestnAtmPortSigDurations | |||
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1 | TablestnAtmPortSigDurationTable | not-accessible | current | A list of ATM Port Signaling Duration entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1 | RowstnAtmPortSigDurationEntry | not-accessible | current | Entry contains information about a particular ATM Port Signaling Duration entry. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.1 | ColumnstnAtmPortSigDurIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.2 | ColumnstnAtmPortSigT301Duration | read-only | current | T301 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.3 | ColumnstnAtmPortSigT303Duration | read-only | current | T303 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.4 | ColumnstnAtmPortSigT306Duration | read-only | current | T306 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.5 | ColumnstnAtmPortSigT308Duration | read-only | current | T308 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Intrface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.6 | ColumnstnAtmPortSigT309Duration | read-only | current | T309 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.7 | ColumnstnAtmPortSigT310Duration | read-only | current | T310 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.8 | ColumnstnAtmPortSigT313Duration | read-only | current | T313 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.9 | ColumnstnAtmPortSigT316Duration | read-only | current | T316 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.10 | ColumnstnAtmPortSigT317Duration | read-only | current | T317 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.11 | ColumnstnAtmPortSigT322Duration | read-only | current | T322 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.12 | ColumnstnAtmPortSigT331Duration | read-only | current | T331 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.13 | ColumnstnAtmPortSigT333Duration | read-only | current | T333 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.14 | ColumnstnAtmPortSigT397Duration | read-only | current | T397 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.15 | ColumnstnAtmPortSigT398Duration | read-only | current | T398 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.16 | ColumnstnAtmPortSigT399Duration | read-only | current | T399 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.17 | ColumnstnAtmPortSigSaalRetryDuration | read-only | current | SAAL retry duration. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3 | NodestnAtmPortSigRetries | |||
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1 | TablestnAtmPortSigRetryTable | not-accessible | current | A list of ATM Port Signaling retry entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1 | RowstnAtmPortSigRetryEntry | not-accessible | current | Entry contains information about a ITU-T Q.2931 timer retry counters. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.1 | ColumnstnAtmPortSigRetryIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.2 | ColumnstnAtmPortSigT303Retries | read-only | current | The number of ATM Port Signaling T303 retries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.3 | ColumnstnAtmPortSigT308Retries | read-only | current | The number of ATM Port Signaling T308 retries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.4 | ColumnstnAtmPortSigT316Retries | read-only | current | The number of ATM Port Signaling T316 retries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.5 | ColumnstnAtmPortSigT322Retries | read-only | current | The number of ATM Port Signaling T322 retries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.6 | ColumnstnAtmPortSigT331Retries | read-only | current | The number of ATM Port Signaling T331 retries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2 | TablestnAtmPortSigSSCSTable | not-accessible | current | A list of ATM Port Signaling SSCS entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1 | RowstnAtmPortSigSSCSEntry | not-accessible | current | Entry contains information about a particular Atm Port Signaling SSCS entry. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.1 | ColumnstnAtmPortSigSSCSIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.2 | ColumnstnAtmPortSigSSCSPollDuration | read-only | current | The duration of the SSCS Poll timer in milliseconds. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.3 | ColumnstnAtmPortSigSSCSKeepAliveDuration | read-only | current | The duration of the SSCS keep-alive timer in milliseconds. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.4 | ColumnstnAtmPortSigSSCSIdleDuration | read-only | current | The duration of the SSCS idle timer in milliseconds. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.5 | ColumnstnAtmPortSigSSCSNoRspDuration | read-only | current | The duration of the SSCS no-response timer in milliseconds. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.6 | ColumnstnAtmPortSigSSCSCcDuration | read-only | current | The duration of the SSCS CC timer in milliseconds. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.7 | ColumnstnAtmPortSigSSCSMaxRcvWindowSize | read-only | current | The maximum size on a receive window. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.8 | ColumnstnAtmPortSigSSCSMaxCcRetries | read-only | current | The maximum number of expiries and subsequent connection control PDU retransmissions acceptable before closing the connection. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.9 | ColumnstnAtmPortSigSSCSMaxSdBetwPolls | read-only | current | The maximum number of STAT list elements in a STAT PDU. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.10 | ColumnstnAtmPortSigSSCSMaxStatListElms | read-only | current | The maximum number of STAT list elements in a STAT PDU. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.11 | ColumnstnAtmPortSigSSCSPollAfterRetrans | read-only | current | Whether to send a POLL after retransmitting PDUs. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.12 | ColumnstnAtmPortSigSSCSRepeatUstat | read-only | current | QSAAL only: if true, send two USTATs each time a USTAT is sent. |
| 1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.13 | ColumnstnAtmPortSigSSCSUstatRspToPoll | read-only | current | QSAAL only: whether USTAT PDUs are issued in response to POLLs. |
| 1.3.6.1.4.1.3551.2.6.1.4.4 | NodestnAtmPortTraffic | |||
| 1.3.6.1.4.1.3551.2.6.1.4.4.1 | TablestnAtmPortTrafficTable | not-accessible | current | A list of ATM port traffic entries. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1 | RowstnAtmPortTrafficEntry | not-accessible | current | Entry contains information about a particular ATM port traffic entry. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.1 | ColumnstnAtmPortTrafIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.2 | ColumnstnAtmPortTrafTxCells | read-only | current | The number of ATM cells transmitted. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.3 | ColumnstnAtmPortTrafRxCells | read-only | current | The number of ATM cells received. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.4 | ColumnstnAtmPortTrafTxParityErrors | read-only | current | The number of ATM transmit parity errors. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.5 | ColumnstnAtmPortTrafRxHdrChkSumErrors | read-only | current | The number of received ATM header checksum errors. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.6 | ColumnstnAtmPortTrafPhyParityErrors | read-only | current | The number of ATM physical parity errors. |
| 1.3.6.1.4.1.3551.2.6.1.4.4.1.1.7 | ColumnstnAtmPortTrafCrc10Errors | read-only | current | The number of ATM CRC-10 errors. |
| 1.3.6.1.4.1.3551.2.6.1.5 | NodestnAtmTraces | |||
| 1.3.6.1.4.1.3551.2.6.1.5.1 | NodestnTraceIps | |||
| 1.3.6.1.4.1.3551.2.6.1.5.1.1 | ScalarstnTraceIpsEnabled | read-only | current | Specifies whether IPS tracing is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.5.1.2 | ScalarstnTraceIpsSize | read-only | current | Specifies the maximum IPS trace buffer size multipled by 1024. The IPS trace log file will wrap when it reaches the maximum. Default: 1000 x 1024 Lines |
| 1.3.6.1.4.1.3551.2.6.1.5.1.3 | ScalarstnTraceIpsFile | read-only | current | Specifies the IPS output path and file name. Changes to the path or filename take effect when IPS tracing is disabled and restarted (close file and open new). |
| 1.3.6.1.4.1.3551.2.6.1.5.2 | NodestnTracePd | |||
| 1.3.6.1.4.1.3551.2.6.1.5.2.1 | ScalarstnTracePdProblemEnabled | read-only | current | Specifies whether PD problem tracing is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.5.2.2 | ScalarstnTracePdExceptionEnabled | read-only | current | Specifies whether PD exception tracing is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.5.2.3 | ScalarstnTracePdAuditEnabled | read-only | current | Specifies whether PD audit tracing is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.5.2.4 | ScalarstnTracePdDeveloperEnabled | read-only | current | Specifies whether PD developer tracing is enabled. |
| 1.3.6.1.4.1.3551.2.6.1.5.2.5 | ScalarstnTracePdSize | read-only | current | Specifies the maximum PD trace buffer size multipled by 1024. The PD trace log file will wrap when it reaches the maximum. |
| 1.3.6.1.4.1.3551.2.6.1.5.2.6 | ScalarstnTracePdFile | read-only | current | Specifies the IPS output path and file name. Changes to the path or filename take effect when IPS tracing is disabled and restarted. |
| 1.3.6.1.4.1.3551.2.6.1.6 | NodestnAtmQos | |||
| 1.3.6.1.4.1.3551.2.6.1.6.1 | NodestnQosCLR | |||
| 1.3.6.1.4.1.3551.2.6.1.6.1.1 | ScalarstnQosClass1CLR | read-only | current | QoS Class 1 cell loss ratio. |
| 1.3.6.1.4.1.3551.2.6.1.6.1.2 | ScalarstnQosClass2CLR | read-only | current | QoS Class 2 cell loss ratio. |
| 1.3.6.1.4.1.3551.2.6.1.6.1.3 | ScalarstnQosClass3CLR | read-only | current | QoS Class 3 cell loss ratio. |
| 1.3.6.1.4.1.3551.2.6.1.6.1.4 | ScalarstnQosClass4CLR | read-only | current | QoS Class 4 cell loss ratio. |
| 1.3.6.1.4.1.3551.2.6.1.6.2 | NodestnQosCDV | |||
| 1.3.6.1.4.1.3551.2.6.1.6.2.1 | ScalarstnQosClass1CDV | read-only | current | QoS Class 1 cell delay variation. |
| 1.3.6.1.4.1.3551.2.6.1.6.2.2 | ScalarstnQosClass2CDV | read-only | current | QoS Class 2 cell delay variation. |
| 1.3.6.1.4.1.3551.2.6.1.6.2.3 | ScalarstnQosClass3CDV | read-only | current | QoS Class 3 cell delay variation. |
| 1.3.6.1.4.1.3551.2.6.1.6.2.4 | ScalarstnQosClass4CDV | read-only | current | QoS Class 4 cell delay variation. |
| 1.3.6.1.4.1.3551.2.6.1.6.3 | NodestnQosCTD | |||
| 1.3.6.1.4.1.3551.2.6.1.6.3.1 | ScalarstnQosClass1MaxCTD | read-only | current | QoS Class 1 cell transfer delay. |
| 1.3.6.1.4.1.3551.2.6.1.6.3.2 | ScalarstnQosClass2MaxCTD | read-only | current | QoS Class 2 cell transfer delay. |
| 1.3.6.1.4.1.3551.2.6.1.6.3.3 | ScalarstnQosClass3MaxCTD | read-only | current | QoS Class 3 cell delay transfer. |
| 1.3.6.1.4.1.3551.2.6.1.6.3.4 | ScalarstnQosClass4MaxCTD | read-only | current | QoS Class 4 cell delay transfer. |
| 1.3.6.1.4.1.3551.2.6.1.7 | NodestnAtmAddresses | |||
| 1.3.6.1.4.1.3551.2.6.1.7.1 | TablestnAtmAddressTable | not-accessible | current | A list of ATM address entries. |
| 1.3.6.1.4.1.3551.2.6.1.7.1.1 | RowstnAtmAddressEntry | not-accessible | current | Entry contains information about a particular session. |
| 1.3.6.1.4.1.3551.2.6.1.7.1.1.1 | ColumnstnAtmAddrIfIndex | read-only | current | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module. |
| 1.3.6.1.4.1.3551.2.6.1.7.1.1.2 | ColumnstnAtmAddrAddress | read-only | current | The value of the ATM NSAP address. |
| 1.3.6.1.4.1.3551.2.6.1.7.1.1.3 | ColumnstnAtmAddrAddressLen | read-only | current | The number of relevent bits in the ATM address. |
| 1.3.6.1.4.1.3551.2.6.1.8 | NodestnAtmThresholds | |||
| 1.3.6.1.4.1.3551.2.6.1.8.1 | TablestnAtmThresholdTable | not-accessible | current | A list of ATM threshold entries. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1 | RowstnAtmThresholdEntry | not-accessible | current | Entry contains information about a particular ATM threshold entry. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.1 | ColumnstnAtmTholdTgrpId | read-only | current | Specifies the threshold group indentifier. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.2 | ColumnstnAtmTholdRegionId | read-only | current | Region identifier within a threshold group. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.3 | ColumnstnAtmTholdCellLowerLimit | read-only | current | Lower Cell number limit for region. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.4 | ColumnstnAtmTholdCellUpperLimit | read-only | current | Upper Cell number limit for region. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.5 | ColumnstnAtmTholdCellQLimitMarking | read-only | current | Queue limit for any flow above which EFCI marking occurs. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.6 | ColumnstnAtmTholdQLimitDiscard | read-only | current | Queue limit for any flow above which Discard processing occurs. |
| 1.3.6.1.4.1.3551.2.6.1.8.1.1.7 | ColumnstnAtmTholdQueueLimit | read-only | current | Queue limit for any flow above which cells are automatically discarded. |
| 1.3.6.1.4.1.3551.2.6.1.9 | NodestnAtmAcct | |||
| 1.3.6.1.4.1.3551.2.6.1.9.1 | ScalarstnAtmAcctEnabled | read-only | current | Specifies whether account logging is turned on or off. |
| 1.3.6.1.4.1.3551.2.6.1.9.2 | ScalarstnAtmAcctMaxSize | read-only | current | Specifies the maximum accounting log buffer size. in Kbytes. The accounting log file will be closed when it reaches the maximum size and the name appended with… |
| 1.3.6.1.4.1.3551.2.6.1.9.3 | ScalarstnAtmAcctMaxFiles | read-only | current | Specifies the maximum number of history files to be stored. Once the maximum number of files is reached, the oldest file is deleted. |
| 1.3.6.1.4.1.3551.2.6.1.9.4 | ScalarstnAtmAcctFilePath | read-only | current | Specifies the accounting log output path and file name on remote device. |
| 1.3.6.1.4.1.3551.2.6.1.9.5 | ScalarstnAtmAcctFtpServer1 | read-only | current | The IP address of the first remote FTP server. |
| 1.3.6.1.4.1.3551.2.6.1.9.6 | ScalarstnAtmAcctFtpUserName1 | read-only | current | The first FTP server username. |
| 1.3.6.1.4.1.3551.2.6.1.9.7 | ScalarstnAtmAcctFtpPassword1 | not-accessible | current | The first FTP server password. |
| 1.3.6.1.4.1.3551.2.6.1.9.8 | ScalarstnAtmAcctFtpServer2 | read-only | current | The IP address of the second remote FTP server. |
| 1.3.6.1.4.1.3551.2.6.1.9.9 | ScalarstnAtmAcctFtpUserName2 | read-only | current | The second FTP server username. |
| 1.3.6.1.4.1.3551.2.6.1.9.10 | ScalarstnAtmAcctFtpPassword2 | not-accessible | current | The second FTP server password. |
| 1.3.6.1.4.1.3551.2.6.1.9.11 | ScalarstnAtmAcctFtpServer3 | read-only | current | The IP address of the third remote FTP server. |
| 1.3.6.1.4.1.3551.2.6.1.9.12 | ScalarstnAtmAcctFtpUserName3 | read-only | current | The third FTP server username. |
| 1.3.6.1.4.1.3551.2.6.1.9.13 | ScalarstnAtmAcctFtpPassword3 | not-accessible | current | The third FTP server password. |
| 1.3.6.1.4.1.3551.2.6.1.9.14 | ScalarstnAtmAcctCurrentFtpServer | read-only | current | The IP address of the current FTP server. |
| 1.3.6.1.4.1.3551.2.6.1.9.15 | ScalarstnAtmAcctPreviousFtpServer | read-only | current | The IP address of the previous FTP server. |
| 1.3.6.1.4.1.3551.2.6.2 | NodestnAtmMibConformance | |||
| 1.3.6.1.4.1.3551.2.100.0.15 | NotificationstnCdrServerFailure | current | A stnCdrServerFailure trap signifies that the agent entity has detected that the accounting server has failed over to an auxilary server. The generation of thi… | |
| 1.3.6.1.4.1.3551.2.100.0.16 | NotificationstnCdrLogFailure | current | A stnCdrLogFailure trap signifies that the agent entity has detected that all accounting servers are inaccessible. Accounting data could be lost. The generatio… | |
| 1.3.6.1.4.1.3551.2.100.0.31 | NotificationstnConfigAuditPvcFailure | current | A stnConfigAuditPvcFailure trap signifies that the agent entity has detected an inconsistency between an active and configured PVC after a failover. The genera… | |
| 1.3.6.1.4.1.3551.2.100.0.32 | NotificationstnConfigAuditSpvcFailure | current | A stnConfigAuditSpvcFailure trap signifies that the agent entity has detected an inconsistency between an active and configured SPVC after a failover. The gene… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AtmPortOperStatus | INTEGER { active(1), inactive(2) } | current | Operational status of an ATM port. |
| TrafficDescrOperStatus | INTEGER { active(1), not-in-service(2), not-ready(3), create-and-go(4), create-and-wait(5), destroy(6) } | current | Operational status of a traffic descriptor. |
| VcCrossConnOperStatus | INTEGER { active(1), not-in-service(2), not-ready(3), create-and-go(4), create-and-wait(5), destroy(6) } | current | Operational status of a VC cross connection. |
| VcLinkOperStatus | INTEGER { active(1), not-in-service(2), not-ready(3), create-and-go(4), create-and-wait(5), destroy(6) } | current | Operational status of a VC Link. |