MIB Viewer

SYMMGNSS

54 objects
This is the Symmetricom common MIB for GNSS/GPS. This MIB has two main nodes: gnssStatus and gnssConfig. The gnssStatus node has a port status table, a satellite table, and a scalar for GNSS current position mode. The gnssConfig node has a configuration table, position setting table, and a present position table.
Imported Objects
ENTITY-MIBentPhysicalIndex
IF-MIBifIndex ifNumber
SNMPv2-CONFMODULE-COMPLIANCE OBJECT-GROUP
SNMPv2-SMIInteger32 MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE
SNMPv2-TCDisplayString TEXTUAL-CONVENTION
SYMM-COMMON-SMIGNSSHealthStatus GNSSPositionMode GNSSReceiverMode symmPhysicalSignal YESVALUETYPE
OIDNameAccessStatusDescription
1.3.6.1.4.1.9070.1.2.5.2.1IdentitysymmGNSSThis is the Symmetricom common MIB for GNSS/GPS. This MIB has two main nodes: gnssStatus and gnssConfig. The gnssStatus node has a port status table, a satelli…
1.3.6.1.4.1.9070.1.2.5.2.1.1NodegnssStatus
1.3.6.1.4.1.9070.1.2.5.2.1.1.1TablegnssPortStatusTablenot-accessiblecurrentGNSS port status table. It contains port name and the current GNSS receiver mode for the specified port.
1.3.6.1.4.1.9070.1.2.5.2.1.1.1.1RowgnssPortStatusEntrynot-accessiblecurrentAn entry of the GNSS port status table. Table index is ifIndex.
1.3.6.1.4.1.9070.1.2.5.2.1.1.1.1.1ColumngnssPortStatusIndexnot-accessiblecurrentLocal index of the GNSS port status table.
1.3.6.1.4.1.9070.1.2.5.2.1.1.1.1.2ColumngnssPortStatusPortNameread-onlycurrentThe name of the specified GNSS port. In TP5000 system there can be one or two GNSS ports. One of them is always called GPS, and the additional one (if present)…
1.3.6.1.4.1.9070.1.2.5.2.1.1.1.1.3ColumngnssPortCurrentGNSSread-onlycurrentThis value indicates whether the specified GNSS port is used. Its value is Yes (1) or No (2). If it is No, the port is considered absent in the system.
1.3.6.1.4.1.9070.1.2.5.2.1.1.1.1.4ColumngnssPortCurrentPosModeread-onlycurrentCurrent position mode of the GNSS receiver. It can be surveying (1), position hold (2), or manual (3)
1.3.6.1.4.1.9070.1.2.5.2.1.1.2TablegnssSatTablenot-accessiblecurrentGNSS satellite table. This table lists information about the satellites being tracked by the GNSS receiver.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1RowgnssSatEntrynot-accessiblecurrentAn entry of the GNSS satellite tracking table. Table index is local index gnssSatIndex.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.1ColumngnssSatIndexread-onlycurrentThis is the local index of the table of the GNSS satellites GPS, GLONASS, Galileo being tracked.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.2ColumngnssSatNumread-onlycurrentGNSS satellite number. This is the identification number of the GNSS satellite being tracked. This information is obtained from the GNSS satellite ephemeris or…
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.3ColumngnssSatSNRread-onlycurrentSignal-to-Noise Ratio. This is the GNSS signal to noise ratio measured by the GNSS receiver.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.4ColumngnssSatHealthread-onlycurrentGNSS satellite health state. It can be healthy (1) or unhealthy (2). This data is obtained from the GNSS receiver.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.5ColumngnssSatAzimuthread-onlycurrentGNSS satellite azimuthal angle clockwise from true north. Range of the azimuth is 0 to 360 degrees.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.6ColumngnssSatElevationread-onlycurrentGNSS satellite elevation angle relative to the horizon. Range of the elevation angle is 0 to 90 degrees.
1.3.6.1.4.1.9070.1.2.5.2.1.1.2.1.7ColumngnssSatPortNameread-onlycurrentThe gnss port name. This is defined in gnssConfigTable.
1.3.6.1.4.1.9070.1.2.5.2.1.1.3TablegnssPresentPosTablenot-accessiblecurrentCurrent position table. This table shows the position of the GNSS receiver antenna. In the automatic mode, the position is calculated by the GNSS receiver. In …
1.3.6.1.4.1.9070.1.2.5.2.1.1.3.1RowgnssPresentPosEntrynot-accessiblecurrentAn entry of the current position table. Table index is the ifIndex.
1.3.6.1.4.1.9070.1.2.5.2.1.1.3.1.1ColumngnssPresentPosIndexnot-accessiblecurrentLocal index that corresponds to the ifIndex. For TP5K there are up to two GNSS port entries.
1.3.6.1.4.1.9070.1.2.5.2.1.1.3.1.2ColumngnssPresentPosLatread-onlycurrentLatitude of the GNSS receiver antenna position for the specified GNSS port. Its format is Ndd:mm:ss.ss or Sdd:mm:ss.ss.
1.3.6.1.4.1.9070.1.2.5.2.1.1.3.1.3ColumngnssPresentPosLongread-onlycurrentLongitude of the GNSS receiver antenna position for the specified GNSS port. Its format is Eddd:mm:ss.ss or Wddd:mm:ss.ss.
1.3.6.1.4.1.9070.1.2.5.2.1.1.3.1.4ColumngnssPresentPosHeightread-onlycurrentAltitude (height) in meters of the GNSS receiver antenna position for the specified GNSS port. Its format is +/-hhhh.h.
1.3.6.1.4.1.9070.1.2.5.2.1.2NodegnssConfig
1.3.6.1.4.1.9070.1.2.5.2.1.2.1TablegnssConfigurationTablenot-accessiblecurrentThe GNSS configuration table.
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1RowgnssConfigurationEntrynot-accessiblecurrentAn entry of the GNSS configuration table. Table index is ifIndex.
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.1ColumngnssConfigurationIndexnot-accessiblecurrentLocal index of the GNSS port configuration table.
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.2ColumngnssConfigurationPortNameread-onlycurrentName of the specified GNSS port. For TP5000 currently there are two names for a GNSS port: GPS or GNSS. Use the name on the equipment front panel.
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.3ColumngnssConfigurationTrackModeread-writecurrentGNSS receiver mode. This depends on the GNSS receiver. For the VCOM receiver, there are four modes: beidou (1), gps (2), priorityBeidou (4), which is automatic…
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.4ColumngnssConfigurationPosModeread-writecurrentGNSS receiver position survey mode. It can be either automatic (1) or manual (2). When the position survey mode is manual, the user must configure the position.
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.5ColumngnssConfigurationElevMaskread-writecurrentGNSS elevation mask. The range is 5 to 45 degrees. This value is actually the lower limit of the elevation mask. The upper limit is 90 degrees. If the elevatio…
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.6ColumngnssConfigurationCableDelayread-writecurrentGNSS antenna cable delay compensation in nanoseconds. Range is 0 to 999,999 nanoseconds. This value should be as close to the actual antenna cable delay as pos…
1.3.6.1.4.1.9070.1.2.5.2.1.2.1.1.7ColumngnssConfigurationLeapSecondsread-writecurrentLeapseconds used for GLONASS only satellite to set user-provided value. Range 20-255. This leapseconds not applicable for GPS port. Note: zero (0) indicates No…
1.3.6.1.4.1.9070.1.2.5.2.1.2.2TablegnssPosSettingTablenot-accessiblecurrentThis table is used to manually set the GNSS receiver antenna position for the specified GNSS port.
1.3.6.1.4.1.9070.1.2.5.2.1.2.2.1RowgnssPosSettingEntrynot-accessiblecurrentAn entry of the GNSS position setting table. Table index is ifIndex.
1.3.6.1.4.1.9070.1.2.5.2.1.2.2.1.1ColumngnssPosSettingIndexnot-accessiblecurrentLocal index that corresponds to the ifIndex. For TP5K there are up to two GNSS port entries.
1.3.6.1.4.1.9070.1.2.5.2.1.2.2.1.2ColumngnssPosSettingLatread-writecurrentManual setting for the latitude of the GNSS receiver antenna for the specified GNSS port.
1.3.6.1.4.1.9070.1.2.5.2.1.2.2.1.3ColumngnssPosSettingLongread-writecurrentManual setting for the longitude of the GNSS receiver antenna for the specified GNSS port.
1.3.6.1.4.1.9070.1.2.5.2.1.2.2.1.4ColumngnssPosSettingHeightread-writecurrentManual setting for the height of the GNSS receiver antenna for the specified GNSS port.
1.3.6.1.4.1.9070.1.2.5.2.1.3IdentitygnssConformancecurrentThis subtree contains conformance statements for the SYMMETRICOM-LED-MIB module.
1.3.6.1.4.1.9070.1.2.5.2.1.3.1NodegnssCompliances
1.3.6.1.4.1.9070.1.2.5.2.1.3.1.1CompliancegnssBasicCompliancecurrentThe compliance statement for SNMP entities which have GNSS input.
1.3.6.1.4.1.9070.1.2.5.2.1.3.2NodegnssUocGroups
1.3.6.1.4.1.9070.1.2.5.2.1.3.2.1GroupgnssStatusGroupcurrentA collection of objects providing information applicable to GNSS status group.
1.3.6.1.4.1.9070.1.2.5.2.1.3.2.2GroupgnssConfigGroupcurrentA collection of objects providing information applicable to GNSS configuration group.
1.3.6.1.4.1.9070.1.2.5.2.1.3.2.3GroupgnssSVGroupcurrentA collection of objects providing information applicable to GNSS satellite positions group.
1.3.6.1.4.1.9070.1.2.5.2.1.3.2.4GroupgnssConfigPosGroupcurrentA collection of objects providing information applicable to GNSS position configuration group.
1.3.6.1.4.1.9070.1.2.5.2.1.3.2.5GroupgnssCurrentPosGroupcurrentA collection of objects providing information applicable to GNSS current position group.
Type Definitions
NameSyntaxStatusDescription
DateAndTimeOCTET STRING (SIZE (8 | 11))currentA date-time specification. field octets contents range 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction f…
GNSSCURPOSITIONMODEINTEGER { surveying(1), positionHold(2), manual(3) }
TAntHeightOCTET STRING (SIZE (4))currentantenna height specification. field octets contents range 1 1 +/- '+' / '-' 2 2-3 meter 0..10000 3 4 meter fraction 0..99 +/- hh.hh
TLatAndLonOCTET STRING (SIZE (5))currentantenna latitude and longitude specification. field octets contents range 1 1 +/-180 deg '+' / '-' 2 2 degree 0..180 3 3 minute 0..59 4 4 second 0..59 5 5 second fraction 0..99 +/- dd:mm:ss.ss
TLocalTimeOffsetOCTET STRING (SIZE (3))currentA local time offset specification. field octets contents range 1 1 direction from UTC '+' / '-' 2 2 hours from UTC* 0..13 3 3 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - The hours rang…
TSsmINTEGER (0..255)currentThe ssm hex code