SYNOPTICS-BASIC-ETHTOK-MIB
434 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.45 | Nodesynoptics | |||
| 1.3.6.1.4.1.45.0 | NodechassisPowerSupplyFailure | Concentrator power supply failure. | ||
| 1.3.6.1.4.1.45.1 | NodechassisFanFailure | Concentrator fan failure. | ||
| 1.3.6.1.4.1.45.1 | Nodeproducts | |||
| 1.3.6.1.4.1.45.1.2 | Nodes3SnmpAgent | |||
| 1.3.6.1.4.1.45.1.2.1 | Nodes3AgentSw | |||
| 1.3.6.1.4.1.45.1.2.1.1 | Scalars3AgentType | read-only | mandatory | The 3000 series agent's Module type. |
| 1.3.6.1.4.1.45.1.2.1.2 | Scalars3AgentFwVer | read-only | mandatory | The agent's module firmware version 0=Rev A,1=Rev B,etc. |
| 1.3.6.1.4.1.45.1.2.1.3 | Scalars3AgentSwMajorVer | read-only | mandatory | The agent major software version number. (version is specified as major.minor.maint or 3.0.1). Object is in decimal. |
| 1.3.6.1.4.1.45.1.2.1.4 | Scalars3AgentSwMinorVer | read-only | mandatory | The agent minor software version number (version is specified as major.minor.maint or 3.0.1). Object is in decimal. |
| 1.3.6.1.4.1.45.1.2.1.5 | Scalars3AgentBootProtocol | read-only | mandatory | Boot protocol used to load the module with its software. On Agents with the Local Load option the value return by this object is valid only if the MIB object s… |
| 1.3.6.1.4.1.45.1.2.1.6 | Scalars3AgentBootFile | read-write | mandatory | The name of the boot file that is sent to the file server during boot time. The actual boot protocol used to retrieve the file is determined by s3AgentBootProt… |
| 1.3.6.1.4.1.45.1.2.1.7 | Scalars3AgentAuthTrap | read-write | deprecated | Enable or disable the use of authentication error trap generation. This parameter will take effect only after a restart (s3AgentRestart) is issued. This parame… |
| 1.3.6.1.4.1.45.1.2.1.8 | Scalars3AgentLocation | read-write | deprecated | This is a informational string that could be used to show the physical location (i.e. area) of the NMM or concentrator. This parameter will take effect only af… |
| 1.3.6.1.4.1.45.1.2.1.9 | Scalars3AgentMibLevel | read-only | mandatory | Used to determine current MIB release supported by agent. The encoding of this object is of the following form: xyy, where x is the major version number and yy… |
| 1.3.6.1.4.1.45.1.2.1.10 | Scalars3AgentFeatureLevel | read-only | deprecated | Used to determine feature level of the agent. The encoding of this object is of the following form: xyy, where x is the major version number and yy is the mino… |
| 1.3.6.1.4.1.45.1.2.1.11 | Scalars3AgentMySlotId | read-only | mandatory | Slot where this agent currently resides. If hardware is unable to determine then a 0 should be returned. |
| 1.3.6.1.4.1.45.1.2.1.12 | Scalars3AgentUnAuthIp | read-only | mandatory | This object contains the IP address of the last station that tried to access this agent with an invalid community string. This object is used as a VarBind in a… |
| 1.3.6.1.4.1.45.1.2.1.13 | Scalars3AgentUnAuthComm | read-only | mandatory | This object contains the community string of the last unauthenticated attempt to access this agent. This object is used as a VarBind in an Authentication Trap … |
| 1.3.6.1.4.1.45.1.2.1.14 | Scalars3AgentSwLicenseCode | read-only | mandatory | The software license code assigned to this agent. This code is required for initializing the agent. The code consists of exactly eight printable characters. |
| 1.3.6.1.4.1.45.1.2.1.15 | Scalars3AgentPerformance | read-only | mandatory | This counts the CPU idle time of the agent in units of 10 microseconds. |
| 1.3.6.1.4.1.45.1.2.1.16 | Scalars3AgentSwMaintVer | read-only | mandatory | The agent software maintenance version number (version is specified as major.minor.maint or 3.0.1). Object is in decimal. |
| 1.3.6.1.4.1.45.1.2.1.17 | Scalars3AgentConfigLoadMode | read-only | mandatory | This indicates whether the agent should get configuration data from the network, use the local configuration data, or try the network first and then fall back … |
| 1.3.6.1.4.1.45.1.2.1.18 | Scalars3AgentConfigActualSource | read-only | mandatory | This indicates whether the agent loaded configuration data from the network or used the local configuration data. |
| 1.3.6.1.4.1.45.1.2.1.19 | Scalars3AgentMgmtProtoMode | read-write | mandatory | This indicates from which network transports over which the agent will accept SNMP requests. This object only applies to agents with IP and IPX dual stack supp… |
| 1.3.6.1.4.1.45.1.2.1.20 | Scalars3AgentActualMgmtProtocol | read-only | mandatory | This indicates which network transports over which the agent will currently accept SNMP requests. |
| 1.3.6.1.4.1.45.1.2.2 | Nodes3AgentNetProtocol | |||
| 1.3.6.1.4.1.45.1.2.2.1 | Nodes3AgentIpProtocol | |||
| 1.3.6.1.4.1.45.1.2.2.1.1 | Scalars3AgentIpAddr | read-write | mandatory | The Agent's administrative IP address. The current operational IP address can be obtained by the ipAdEntAddr entry in the ipAddrTable. This parameter will take… |
| 1.3.6.1.4.1.45.1.2.2.1.2 | Scalars3AgentNetMask | read-write | mandatory | The Agent's administrative subnet mask. The current operational subnet mask can be obtained by the ipAdEntNetMask entry in the ipAddrTable. This parameter will… |
| 1.3.6.1.4.1.45.1.2.2.1.3 | Scalars3AgentDefaultGateway | read-write | mandatory | The Agent's administrative default gateway IP address. The current operational default gateway's IP address can be obtained from the ipRoutingTable. This param… |
| 1.3.6.1.4.1.45.1.2.2.1.4 | Scalars3AgentBootServerAddr | read-write | mandatory | The IP address to which the requests for boot files are sent. The protocol used to retrieve the boot files is determined by object s3AgentBootProtocol. This pa… |
| 1.3.6.1.4.1.45.1.2.2.1.5 | Scalars3AgentSecDefaultGateway | read-write | mandatory | The agent's administrative secondary default gateway IP address. This default gateway's IP address will be used when the primary default gateway (s3AgentDefaul… |
| 1.3.6.1.4.1.45.1.2.2.1.6 | Scalars3AgentPingDefaultRtrSwitch | read-write | mandatory | Controls whether the agent will periodically send out the icmp echos (pings) to the default router(s). The values are: other(1)...unknown or other on(2)......a… |
| 1.3.6.1.4.1.45.1.2.2.1.7 | Scalars3AgentPingDefaultRtrTime | read-write | mandatory | The time interval that the agent uses to send out the pings periodically to the default router(s) to check if the router(s) are still reachable. |
| 1.3.6.1.4.1.45.1.2.2.1.8 | Scalars3AgentBootRouter | read-write | mandatory | The default route IP address used at boot time to download the NMM's agent configuration and image files from the TFTP server. This parameter will not survive … |
| 1.3.6.1.4.1.45.1.2.2.2 | Nodes3AgentIpxProtocol | |||
| 1.3.6.1.4.1.45.1.2.2.2.1 | Scalars3AgentIpxAddr | read-only | mandatory | The current IPX address used by this agent. |
| 1.3.6.1.4.1.45.1.2.2.2.3 | Scalars3AgentUnAuthIpx | read-only | mandatory | This object contains the IPX address of the last station that tried to access this agent with an invalid community string. This object is used as a VarBind in … |
| 1.3.6.1.4.1.45.1.2.3 | Tables3AgentTrapReceiverTable | not-accessible | mandatory | Table containing list of NMS's that are to receive traps generated by this NMM. |
| 1.3.6.1.4.1.45.1.2.3.1 | Rows3AgentTrapReceiverEntry | not-accessible | mandatory | A destination address and community string to a particular trap server, along with a trap filter and entry aging capability. |
| 1.3.6.1.4.1.45.1.2.3.1.1 | Columns3AgentTrapRcvrStatus | read-write | mandatory | Setting this object to the value invalid(3) has the effect of invalidating the corresponding entry in the s3AgentTrapReceiverTable. That is, it effectively dis… |
| 1.3.6.1.4.1.45.1.2.3.1.2 | Columns3AgentTrapRcvrNetAddress | read-write | mandatory | IP address for trap server that is to receive the trap. |
| 1.3.6.1.4.1.45.1.2.3.1.3 | Columns3AgentTrapRcvrComm | read-write | mandatory | Community string used for traps sent to this trap receiver. |
| 1.3.6.1.4.1.45.1.2.3.1.4 | Columns3AgentTrapRcvrAgeTime | read-write | mandatory | This is the time interval used to age entries out of the trap receiver table. The default value if not specified will be 0, or infinite, never to be aged out. |
| 1.3.6.1.4.1.45.1.2.4 | Nodes3AgentHw | |||
| 1.3.6.1.4.1.45.1.2.4.1 | Scalars3AgentStatus | read-write | mandatory | This indicates whether the NMM is online(2) and operating, or offline(1) (ie: not connected to the concentrator backplane). ***ACCESS VARIATION - changed acces… |
| 1.3.6.1.4.1.45.1.2.4.2 | Scalars3AgentMdaHwVer | read-only | mandatory | The network management module's MDA hardware version number (0=Rev. A, 1=Rev. B, etc.). |
| 1.3.6.1.4.1.45.1.2.4.3 | Scalars3AgentMode | read-only | mandatory | This indicates whether the NMM is operating in primary(1) or secondary(2) mode. ***ACCESS VARIATION - changed access from read-write |
| 1.3.6.1.4.1.45.1.2.4.4 | Scalars3AgentReset | read-write | mandatory | Network management module reset status. Writing a reset(2) to this object will reset the NMM and perform a download and restart. |
| 1.3.6.1.4.1.45.1.2.4.5 | Scalars3AgentRestart | read-write | mandatory | Network management module restart status. Writing a restart(2) to this object will restart the NMM. This initializes all the counters, re-reads the EEPROM data… |
| 1.3.6.1.4.1.45.1.2.4.6 | Scalars3AgentBootMode | read-write | mandatory | The method for obtaining boot parameter information. The possible values are: eeprom(1)......get boot info from eeprom net(2).........get boot info from remote… |
| 1.3.6.1.4.1.45.1.2.4.7 | Scalars3AgentWriteEeprom | read-write | mandatory | Network management module EEPROM write status. Writing a (2) to this object will write the contents of current EEPROM data structure in the EEPROM. |
| 1.3.6.1.4.1.45.1.2.4.8 | Scalars3AgentBaudRate | read-write | mandatory | Specifies the baud rate in bits per second of either the internal modem or the RS-232 port. This parameter will take effect only after a restart (s3AgentRestar… |
| 1.3.6.1.4.1.45.1.2.4.9 | Scalars3AgentInitString | read-write | mandatory | This is the initialization string used to establish the out-of-band connection. (i.e. could contain the string ATDT,415-960-1100 for an internal or external mo… |
| 1.3.6.1.4.1.45.1.2.4.10 | Scalars3AgentEepromSize | read-only | mandatory | The size of the EEPROM of the agent in units of bytes. |
| 1.3.6.1.4.1.45.1.2.4.11 | Scalars3AgentEpromSize | read-only | mandatory | The size of the EPROM of the agent in units of bytes. |
| 1.3.6.1.4.1.45.1.2.4.12 | Scalars3AgentDramSize | read-only | mandatory | The size of the DRAM of the agent in units of bytes. |
| 1.3.6.1.4.1.45.1.2.4.13 | Scalars3AgentHexDisplay | read-only | mandatory | The current 4 ASCII character display of the agent. Agents with no hex display hardware should return a zero length string. |
| 1.3.6.1.4.1.45.1.2.4.14 | Scalars3AgentFlashStatus | read-only | mandatory | This indicates the operational status of the flash device of the agent. A fail(3) indicates that either the flash device configuration on board is not valid or… |
| 1.3.6.1.4.1.45.1.2.6 | Nodes3AgentLocImage | |||
| 1.3.6.1.4.1.45.1.2.6.1 | Scalars3LocImageValid | read-only | mandatory | This indicates whether the agent has a valid local code image on board. An EPROM checksum failure would cause the agent to return localImageInvalid(3). |
| 1.3.6.1.4.1.45.1.2.6.2 | Scalars3LocImageMajorVersion | read-only | mandatory | The major software version number of the locally-stored image. This object applies only to agents with valid local image. Other agents should return zero. |
| 1.3.6.1.4.1.45.1.2.6.3 | Scalars3LocImageMinorVersion | read-only | mandatory | The minor software version number of the locally-stored image. This object applies only to agents with valid local image. Other agents should return zero. |
| 1.3.6.1.4.1.45.1.2.6.4 | Scalars3LocImageLoadMode | read-write | mandatory | This indicates whether the agent should get code from the network, use a local image, or try the network first and then fall back to local image if the network… |
| 1.3.6.1.4.1.45.1.2.6.5 | Scalars3LocImageActualSource | read-only | mandatory | This indicates whether the agent loaded code from the network or used a local image. When the the ImageLoadMode is localAsBackup, this variable indicates wheth… |
| 1.3.6.1.4.1.45.1.2.6.6 | Scalars3LocImageMaintVersion | read-only | mandatory | The maintenance software version number of the locally-stored image. This object applies only to agents with valid local image. Other agents should return zero. |
| 1.3.6.1.4.1.45.1.2.7 | Tables3AgentIpxTrapReceiverTable | not-accessible | mandatory | Table containing list of NMS's that are to receive traps generated by this NMM sent over IPX. |
| 1.3.6.1.4.1.45.1.2.7.1 | Rows3AgentIpxTrapReceiverEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.45.1.2.7.1.1 | Columns3AgentIpxTrapRcvrStatus | read-write | mandatory | Action/status for the row. The values that can be written are: valid(2).....create row invalid(3)...delete row The values that can be read are: other(1).....so… |
| 1.3.6.1.4.1.45.1.2.7.1.2 | Columns3AgentIpxTrapRcvrNetAddress | read-write | mandatory | IPX address for trap server that is to receive the trap. The value may only be written when the row is created. |
| 1.3.6.1.4.1.45.1.2.7.1.3 | Columns3AgentIpxTrapRcvrComm | read-write | mandatory | Community string used for traps sent to this trap receiver. |
| 1.3.6.1.4.1.45.1.2.7.1.4 | Columns3AgentIpxTrapRcvrAgeTime | read-write | mandatory | This is the time interval used to age entries out of the trap receiver table. The default value if not specified will be 0, or infinite, never to be aged out. |
| 1.3.6.1.4.1.45.1.3 | Nodeseries3000 | |||
| 1.3.6.1.4.1.45.1.3.1 | Nodes3000Chassis | |||
| 1.3.6.1.4.1.45.1.3.1.1 | Scalars3ChassisType | read-only | mandatory | The chassis type. |
| 1.3.6.1.4.1.45.1.3.1.2 | Scalars3ChassisBkplType | read-only | mandatory | The chassis backplane type. |
| 1.3.6.1.4.1.45.1.3.1.3 | Scalars3ChassisBkplRev | read-only | mandatory | The chassis backplane revision. |
| 1.3.6.1.4.1.45.1.3.1.4 | Scalars3ChassisPsType | read-only | mandatory | The chassis power supply type. This value is valid only when the backplane type is not other(1). If the chassis has a redundant backplane, the agent returns re… |
| 1.3.6.1.4.1.45.1.3.1.5 | Scalars3ChassisPsStatus | read-only | mandatory | The chassis power supply status. |
| 1.3.6.1.4.1.45.1.3.1.6 | Scalars3ChassisFanStatus | read-only | mandatory | The status of the chassis cooling fan. |
| 1.3.6.1.4.1.45.1.3.1.7 | Tables3SlotConfigTable | not-accessible | mandatory | The chassis slot configuration table. |
| 1.3.6.1.4.1.45.1.3.1.7.1 | Rows3SlotConfigEntry | not-accessible | mandatory | What type of module is in each slot of the chassis. |
| 1.3.6.1.4.1.45.1.3.1.7.1.1 | Columns3SlotNumber | read-only | mandatory | The 3000 Chassis slot number. Valid entries are 1-12. |
| 1.3.6.1.4.1.45.1.3.1.7.1.2 | Columns3SlotModuleId | read-only | mandatory | ID for the module. Values are specified in SynOptics technical documents. |
| 1.3.6.1.4.1.45.1.3.1.7.1.3 | Columns3SlotModuleType | read-only | deprecated | The type of module this entry represents. Values are specified in SynOptics technical documents. |
| 1.3.6.1.4.1.45.1.3.1.7.1.4 | Columns3SlotModuleDescr | read-only | mandatory | Module description. Values are specified in SynOptics technical documents. |
| 1.3.6.1.4.1.45.1.3.1.7.1.5 | Columns3SlotModuleLed | read-only | mandatory | Status of the module LEDs. Format is specified in SynOptics technical documents. NOTE: the 291x FDDI workgroup concentrators actually return a string with size… |
| 1.3.6.1.4.1.45.1.3.1.7.1.6 | Columns3SlotModuleMdaId | read-only | mandatory | ID of the medium-dependent part of the board. The value is board dependent. Values are specified in SynOptics technical documents. |
| 1.3.6.1.4.1.45.1.3.1.8 | Tables3CommonBoardTable | not-accessible | mandatory | A table containing information about the boards currently plugged into the 3000 Chassis. This board table contains an entry for each non-empty slot in the s3Sl… |
| 1.3.6.1.4.1.45.1.3.1.8.1 | Rows3CommonBoardEntry | not-accessible | mandatory | A table entry containing information about a single Board currently plugged into the 3000 Chassis. These values can be retrieved using the common board NMI com… |
| 1.3.6.1.4.1.45.1.3.1.8.1.1 | Columns3CommonBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.1.8.1.2 | Columns3CommonBoardId | read-only | mandatory | This is the ID of the board, which is 'hard-coded' in the board, and identifies the board's basic functionality. Some boards have the capability to change aspe… |
| 1.3.6.1.4.1.45.1.3.1.8.1.3 | Columns3CommonBoardHwVer | read-only | mandatory | The hardware revision of the board. 0=Rev. A, 1=Rev. B, etc. |
| 1.3.6.1.4.1.45.1.3.1.8.1.4 | Columns3CommonBoardStatus | read-only | mandatory | This indicates the operational status of the board. |
| 1.3.6.1.4.1.45.1.3.1.8.1.5 | Columns3CommonBoardReset | read-write | mandatory | This indicates the reset state of the board. Writing with the value reset (2) will reset the board. |
| 1.3.6.1.4.1.45.1.3.1.8.1.6 | Columns3CommonBoardPartStatus | read-write | mandatory | Tells whether the board is partitioned or enabled. Writing with the value partition(2) will partition the board indefinitely and writing with the value enabled… |
| 1.3.6.1.4.1.45.1.3.1.8.1.7 | Columns3CommonBoardNmCntlStatus | read-only | mandatory | Tells whether the board is under network management control. The value nmControl(2) indicates that the board or one or more ports are being controlled by netwo… |
| 1.3.6.1.4.1.45.1.3.1.8.1.8 | Columns3CommonBoardPsStatus | read-only | mandatory | This indicates the operational status of the board power supply. A fail(2) indicates that one of the power supplies on the board has failed. |
| 1.3.6.1.4.1.45.1.3.1.8.1.9 | Columns3CommonBoardPartTime | read-write | mandatory | When partitioning the board for a specified time, s3CommonBoardPartStatus must be set with timedPartition(3) and this object must be supplied with the duration… |
| 1.3.6.1.4.1.45.1.3.1.9 | Scalars3SlotConfigOctetString | read-only | mandatory | Packed octet string for the slot configuration table. Format is specified in SynOptics technical documents. NOTE: the 291x FDDI workgroup concentrators actuall… |
| 1.3.6.1.4.1.45.1.3.1.10 | Nodes3000RedundantPs | |||
| 1.3.6.1.4.1.45.1.3.1.10.1 | Scalars3RedPsPlus5vCurrent | read-only | mandatory | This gauge is measured in amperes. |
| 1.3.6.1.4.1.45.1.3.1.10.2 | Scalars3RedPsPlus12vCurrent | read-only | mandatory | This gauge is measured in amperes. |
| 1.3.6.1.4.1.45.1.3.1.10.3 | Scalars3RedPsAmbientTempStatus | read-only | mandatory | This status indicates whether the ambient temperature is normal, i.e., below 40 degree C. |
| 1.3.6.1.4.1.45.1.3.1.10.4 | Scalars3RedPsAmbientTemperature | read-only | mandatory | This gauge is measured in Celsius. |
| 1.3.6.1.4.1.45.1.3.1.10.5 | Scalars3RedPsPrimaryConfig | read-only | mandatory | This indicates the primary power supply type (PS 1). Note that value redundantCapable(5) should not be returned for this object. |
| 1.3.6.1.4.1.45.1.3.1.10.6 | Scalars3RedPsSecondaryConfig | read-only | mandatory | This indicates the secondary power supply type (PS 2). Note that value redundantCapable(5) should not be returned for this object. |
| 1.3.6.1.4.1.45.1.3.1.10.7 | Scalars3RedPsDiodeStatus | read-only | mandatory | This gives the status of the summing diode on the 3100R associated with the indicated power supply. |
| 1.3.6.1.4.1.45.1.3.1.10.8 | Scalars3RedPsPowerAlarm | read-only | mandatory | This tells whether the indicated power supply is sensing voltage on the backplane. |
| 1.3.6.1.4.1.45.1.3.1.11 | Scalars3ChassisBkPlEthChanDiv | read-only | mandatory | A value that describes the divisions of the segmentable ethernet channel. For those devices that do not implement a backplane with this feature, they still nee… |
| 1.3.6.1.4.1.45.1.3.1.12 | Scalars3ChassisEnetChannelAType | read-only | mandatory | The agent will return aSegmentable(2) for the 3000N, 3000NT, 3000S, 3000SR, and any other backplanes in which Ethernet channel A can be divided into multiple s… |
| 1.3.6.1.4.1.45.1.3.2 | Nodes3000Ethernet | |||
| 1.3.6.1.4.1.45.1.3.2.1 | Nodes3000EnetConcentrator | |||
| 1.3.6.1.4.1.45.1.3.2.1.1 | Scalars3EnetConcRetimingStatus | read-write | mandatory | Does this concentrator have retiming turned on. Writing a 1 will turn off retiming and writing a 2 will turn on retiming. This will change the active state of … |
| 1.3.6.1.4.1.45.1.3.2.1.2 | Scalars3EnetConcFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the concentrator. This does not include frames received with a frame-too-long, runt, FCS, or … |
| 1.3.6.1.4.1.45.1.3.2.1.3 | Scalars3EnetConcOctetsRxOk | read-only | mandatory | Contains a count of data and padding octets in frames that are successfully received by the concentrator. This does not include frames received with a frame-to… |
| 1.3.6.1.4.1.45.1.3.2.1.4 | Scalars3EnetConcMcastFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the concentrator and are directed to an active non-broadcast group address. This does not inc… |
| 1.3.6.1.4.1.45.1.3.2.1.5 | Scalars3EnetConcBcastFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the concentrator and are directed to the broadcast group address. This does not include frame… |
| 1.3.6.1.4.1.45.1.3.2.1.6 | Scalars3EnetConcColls | read-only | mandatory | This contains a count of the collisions at the concentrator level. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level co… |
| 1.3.6.1.4.1.45.1.3.2.1.7 | Scalars3EnetConcTooLongErrors | read-only | mandatory | This contains a count of frames that are received by the concentrator and exceed the maximum permitted frame size. This counter is incremented when the frameTo… |
| 1.3.6.1.4.1.45.1.3.2.1.8 | Scalars3EnetConcRuntErrors | read-only | mandatory | This contains a count of frames received by the concentrator that are less than the minimum permitted frame size and have a good FCS. |
| 1.3.6.1.4.1.45.1.3.2.1.9 | Scalars3EnetConcFragErrors | read-only | mandatory | This contains a count of frames received by the concentrator that are less than the minimum permitted frame size and have a bad FCS or alignment error. |
| 1.3.6.1.4.1.45.1.3.2.1.10 | Scalars3EnetConcAlignErrors | read-only | mandatory | This contains a count of frames received by the concentrator that are not an integral number of octets in length and do not pass the FCS check. This counter is… |
| 1.3.6.1.4.1.45.1.3.2.1.11 | Scalars3EnetConcFcsErrors | read-only | mandatory | This contains a count of frames received by the concentrator that are an integral number of octets in length that do not pass the FCS check. This counter is in… |
| 1.3.6.1.4.1.45.1.3.2.1.12 | Scalars3EnetConcLateCollErrors | read-only | mandatory | This contains a total concentrator count of the late collisions. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level late… |
| 1.3.6.1.4.1.45.1.3.2.1.13 | Scalars3EnetConcSecureStatus | read-write | mandatory | This s3EnetConcSecureStatus object indicates whether the security features (both allowed nodes and LattisSecure) for the concentrator are active or inactive. I… |
| 1.3.6.1.4.1.45.1.3.2.1.14 | Scalars3EnetConcAuthAction | read-write | mandatory | If s3EnetConcSecureStatus is concSecureOn(2) and a violation occurs, then the action specified by this object will take place. On a partition, only the port th… |
| 1.3.6.1.4.1.45.1.3.2.1.15 | Scalars3EnetConcSecurityLock | read-only | mandatory | If s3EnetConcSecurityLock is locked(2), the agent will refuse all requests to modify the 'security configuration' (defined below) by returning a BadValue retur… |
| 1.3.6.1.4.1.45.1.3.2.1.16 | Scalars3EnetConcEnetChan | read-only | mandatory | Identifies the channel to which this NMM is currently monitoring. |
| 1.3.6.1.4.1.45.1.3.2.2 | Nodes3000EnetBoard | |||
| 1.3.6.1.4.1.45.1.3.2.2.1 | Tables3EnetBoardTable | not-accessible | mandatory | A table of board-related objects. The number of entries is given by the number of Ethernet host module and network management module boards that are contained … |
| 1.3.6.1.4.1.45.1.3.2.2.1.1 | Rows3EnetBoardEntry | not-accessible | mandatory | A table containing objects about Ethernet boards which are currently plugged into the 3000 chassis. |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.1 | Columns3EnetBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.9 | Columns3EnetBoardFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the board. This does not include frames received with a frame-too-long, runt, FCS, or alignme… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.10 | Columns3EnetBoardOctetsRxOk | read-only | mandatory | Contains a count of data and padding octets in frames that are successfully received by the board. This does not include frames received with a frame-too-long,… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.11 | Columns3EnetBoardMcastFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the board and are directed to an active non-broadcast group address. This does not include fr… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.12 | Columns3EnetBoardBcastFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the board and are directed to the broadcast group address. This does not include frames recei… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.13 | Columns3EnetBoardColls | read-only | mandatory | This contains a board level count of collisions. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level collision 'flags' fo… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.14 | Columns3EnetBoardTooLongErrors | read-only | mandatory | This contains a count of frames that are received by the board and exceed the maximum permitted frame size. This counter is incremented when the frameTooLong e… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.15 | Columns3EnetBoardRuntErrors | read-only | mandatory | This contains a count of frames received by the board that are less than the minimum permitted frame size and have a good FCS. |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.16 | Columns3EnetBoardAlignErrors | read-only | mandatory | This contains a count of frames received by the board that are not an integral number of octets in length and do not pass the FCS check. This counter is increm… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.17 | Columns3EnetBoardFcsErrors | read-only | mandatory | This contains a count of frames received by the board that are an integral number of octets in length that do not pass the FCS check. This counter is increment… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.18 | Columns3EnetBoardLateCollErrors | read-only | mandatory | This contains a count of the board level late collisions. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level late collis… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.19 | Columns3EnetBoardAuthStatus | read-write | mandatory | This object is only used if s3EnetConcSecureStatus is set to slotCheckOn(4). In this case, turning this object on(2) means that any node that is heard on this … |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.20 | Columns3EnetBoardAuthAction | read-write | mandatory | If s3EnetConcSecureStatus is slotCheckOn(4) and s3EnetBoardAuthStatus is on(2) and an authorized nodes violation occurs on the board, then the action specified… |
| 1.3.6.1.4.1.45.1.3.2.2.1.1.21 | Columns3EnetBoardUpStamp | read-only | mandatory | The time ( in hundredths of a second) that the board was first seen as a member of this NMM's segment. |
| 1.3.6.1.4.1.45.1.3.2.2.2 | Nodes3000EnetLocBridge | |||
| 1.3.6.1.4.1.45.1.3.2.2.2.1 | Tables3EnetLocBridgeSlotTable | not-accessible | mandatory | A table of Local Bridge Board entries. The number of entries is determined by the Concentrator Slot Configuration Table. Only those entries that are Ethernet l… |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1 | Rows3EnetLocBridgeEntry | not-accessible | mandatory | A table containing objects about Boards which are local bridges that are currently plugged into the 3000 chassis. |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1.1 | Columns3EnetLocBridgeIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1.2 | Columns3EnetLocBridgeDescr | read-only | mandatory | Description of the local bridge board. |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1.3 | Columns3EnetLocBridgePortCount | read-only | mandatory | Number of ports that are on the local bridge board. |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1.4 | Columns3EnetLocBridgeDiagSts | read-only | mandatory | Latest Diagnostic LED Status that has been recorded. |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1.5 | Columns3EnetLocBridgeBootSts | read-only | mandatory | The current status of the board as it relates to rebooting. |
| 1.3.6.1.4.1.45.1.3.2.2.2.1.1.6 | Columns3EnetLocBridgeStandbySts | read-only | mandatory | This status says whether the local bridge is active or in standby mode. |
| 1.3.6.1.4.1.45.1.3.2.2.2.2 | Tables3EnetLocBridgePortTable | not-accessible | mandatory | A table of Port entries that are part of a local bridge. The number of entries is determined by knowing the number of local bridge boards that are installed by… |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1 | Rows3EnetLocBridgePortEntry | not-accessible | mandatory | A table containing objects about the ports of the local bridges that are currently plugged into the 3000 chassis. |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1.1 | Columns3EnetLocBridgePortSlotIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1.2 | Columns3EnetLocBridgePortIndex | read-only | mandatory | A unique value for each port. Its value ranges between 1 and 12. The value for each port must remain constant at least from one re-initialization of the entity… |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1.3 | Columns3EnetLocBridgePortMdaId | read-only | mandatory | Medium dependent ID for the port. See s3SlotModuleMdaId in the SynOptics Common MIB. |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1.4 | Columns3EnetLocBridgePortIf | read-only | mandatory | Bridge interface types. |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1.5 | Columns3EnetLocBridgePortDescr | read-only | mandatory | A text description of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.2.2.1.6 | Columns3EnetLocBridgePortOpSts | read-only | mandatory | Operating status of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.3 | Nodes3000EnetRemBridge | |||
| 1.3.6.1.4.1.45.1.3.2.2.3.1 | Tables3EnetRemBridgeSlotTable | not-accessible | mandatory | A table of Remote Bridge Board entries. The number of entries is determined by the Concentrator Slot Configuration Table. Only those entries that are Ethernet … |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1 | Rows3EnetRemBridgeEntry | not-accessible | mandatory | A table containing objects about Boards which are remote bridges that are currently plugged into the 3000 chassis. |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1.1 | Columns3EnetRemBridgeIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1.2 | Columns3EnetRemBridgeDescr | read-only | mandatory | Description of the board. |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1.3 | Columns3EnetRemBridgePortCount | read-only | mandatory | Number of ports that are on the board. |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1.4 | Columns3EnetRemBridgeDiagSts | read-only | mandatory | Latest Diagnostic LED Status that has been recorded. |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1.5 | Columns3EnetRemBridgeBootSts | read-only | mandatory | The current status of the board as it relates to rebooting. |
| 1.3.6.1.4.1.45.1.3.2.2.3.1.1.6 | Columns3EnetRemBridgeStandbySts | read-only | mandatory | This status says whether the remote bridge is active or in standby mode. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2 | Tables3EnetRemBridgePortTable | not-accessible | mandatory | A table of Port entries that are part of a remote bridge. The number of entries is determined by knowing the number of remote bridge boards that are installed … |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1 | Rows3EnetRemBridgePortEntry | not-accessible | mandatory | A table containing objects about the ports of the remote bridges that are currently plugged into the 3000 chassis. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.1 | Columns3EnetRemBridgePortSlotIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.2 | Columns3EnetRemBridgePortIndex | read-only | mandatory | A unique value for each port. Its value ranges between 1 and 12. The value for each port must remain constant at least from one re-initialization of the entity… |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.3 | Columns3EnetRemBridgePortMdaId | read-only | mandatory | Medium dependent ID for the port. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.4 | Columns3EnetRemBridgePortDescr | read-only | mandatory | A text description of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.5 | Columns3EnetRemBridgePortOpSts | read-only | mandatory | Operating status of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.6 | Columns3EnetRemBridgePortRdySnd | read-only | mandatory | Ready to send status of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.7 | Columns3EnetRemBridgePortClrSnd | read-only | mandatory | Clear to send status of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.3.2.1.8 | Columns3EnetRemBridgePortCarDt | read-only | mandatory | Carrier detect status of the port. |
| 1.3.6.1.4.1.45.1.3.2.2.4 | Nodes3000EnetRouter | |||
| 1.3.6.1.4.1.45.1.3.2.2.4.1 | Tables3EnetRouterSlotTable | not-accessible | mandatory | A table of Router Board entries. The number of entries is determined by the Concentrator Slot Configuration Table. Only those entries that are Ethernet routers… |
| 1.3.6.1.4.1.45.1.3.2.2.4.1.1 | Rows3EnetRouterEntry | not-accessible | mandatory | A table containing objects about Boards which are routers that are currently plugged into the 3000 chassis. |
| 1.3.6.1.4.1.45.1.3.2.2.4.1.1.1 | Columns3EnetRouterIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.4.1.1.2 | Columns3EnetRouterDescr | read-only | mandatory | Description of the router board. |
| 1.3.6.1.4.1.45.1.3.2.2.4.1.1.3 | Columns3EnetRouterDiagSts | read-only | mandatory | Latest Diagnostic LED Status that has been recorded. |
| 1.3.6.1.4.1.45.1.3.2.2.4.1.1.4 | Columns3EnetRouterStandbySts | read-only | mandatory | This status says whether the router is active or in standby mode. |
| 1.3.6.1.4.1.45.1.3.2.2.5 | Tables3EnetCommonBoardTable | not-accessible | mandatory | Information maintained for each Ethernet board. The information can be retrieved for any Ethernet board, even if the board is not on the same backplane Etherne… |
| 1.3.6.1.4.1.45.1.3.2.2.5.1 | Rows3EnetCommonBoardEntry | not-accessible | mandatory | There is one entry per Ethernet board in this table. |
| 1.3.6.1.4.1.45.1.3.2.2.5.1.1 | Columns3EnetCommonBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.2.5.1.2 | Columns3EnetCommonBoardEnetAB | read-write | mandatory | The channel to which the board is connected. The primary use of this object is for providing realtime switching of boards between channel A and channel B. It i… |
| 1.3.6.1.4.1.45.1.3.2.2.5.1.3 | Columns3EnetCommonBoardChanSwitch | read-only | mandatory | The agent will return switchCapable(2) for any Ethernet host board which can be switched between Ethernet channels. The value notSwitchCapable(3) indicates tha… |
| 1.3.6.1.4.1.45.1.3.2.2.5.1.4 | Columns3EnetCommonBoardRedund | read-only | mandatory | The agent will return redundCapable(2) for any Ethernet host board which can provide hardware and/or software controlled redundancy on the port level. The valu… |
| 1.3.6.1.4.1.45.1.3.2.3 | Nodes3000EnetPort | |||
| 1.3.6.1.4.1.45.1.3.2.3.1 | Tables3EnetPortTable | not-accessible | mandatory | A list of port entries. The number of entries is given by learning the type of board from the information in the s3ChassisSlotConfigTable. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1 | Rows3EnetPortEntry | not-accessible | mandatory | A table containing objects about the Ports of each board plugged into the 3000 chassis which are on the same backplane Ethernet segment as the reporting NMM. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.1 | Columns3EnetPortBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one reinitialization of the entit… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.2 | Columns3EnetPortIndex | read-only | mandatory | A unique value for each port. Its value is dependent on the board type. The value for each port must remain constant at least from one re-initialization of the… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.3 | Columns3EnetPortLinkStatus | read-only | deprecated | Tells whether the port is receiving link status. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.4 | Columns3EnetPortPartStatus | read-write | deprecated | This indicates the operational status of the Port. Writing a partition(2) will partition the port indefinitely and enabled(1) will enable the port. If a timed … |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.5 | Columns3EnetPortJabberStatus | read-only | mandatory | Tells whether the DTE connected to the Port is jabbering or not. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.6 | Columns3EnetPortFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the port. This does not include frames received with a frame-too-long, runt, FCS, or alignmen… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.7 | Columns3EnetPortOctetsRxOk | read-only | mandatory | Contains a count of data and padding octets in frames that are successfully received by the port. This does not include frames received with a frame-too-long, … |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.8 | Columns3EnetPortMcastFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the port and are directed to an active non-broadcast group address. This does not include fra… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.9 | Columns3EnetPortBcastFrmsRxOk | read-only | mandatory | This contains a count of frames that are successfully received by the port and are directed to the broadcast group address. This does not include frames receiv… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.10 | Columns3EnetPortColls | read-only | mandatory | This contains a count of collisions. For NMM+ this is a true counter. For other NMMs this is a count of the collision flags. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.11 | Columns3EnetPortTooLongErrors | read-only | mandatory | This contains a count of frames that are received by the port and exceed the maximum permitted frame size. This counter is incremented when the frameTooLong er… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.12 | Columns3EnetPortRuntErrors | read-only | mandatory | This contains a count of frames received by the port that are less than the minimum permitted frame size and have a good FCS. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.13 | Columns3EnetPortAlignErrors | read-only | mandatory | This contains a count of frames received by the port that are not an integral number of octets in length and do not pass the FCS check. This counter is increme… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.14 | Columns3EnetPortFcsErrors | read-only | mandatory | This contains a count of frames received the port that are an integral number of octets in length that do not pass the FCS check. This counter is incremented w… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.15 | Columns3EnetPortLateCollErrors | read-only | mandatory | This contains a count of late collisions. For NMM+ this is a true counter. For other NMMs this is a count of the late collision flags. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.16 | Columns3EnetPortAuthStatus | read-write | mandatory | This object is only used if s3EnetConcSecureStatus is set to portCheckOn(3) or if the port is on a LattisSecure Host Module. In this case, turning this object … |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.17 | Columns3EnetPortAuthAction | read-write | mandatory | If s3EnetConcSecureStatus is portCheckOn(3) or this port is on a LattisSecure Host Module, and s3EnetPortAuthStatus is on(2) and an authorized nodes violation … |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.18 | Columns3EnetPortPartTime | read-write | deprecated | When partitioning the port for a specified time, s3EnetPortPartStatus must be set with timedpartition(4) and this object must be supplied with the duration val… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.19 | Columns3EnetPortType | read-only | deprecated | The media connection type for this port. Note that this object was called s3EnetPortMDIXSwitch in the Ethernet 3.3 and 4.0 MIBs. |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.20 | Columns3EnetPortInterconStatus | read-only | mandatory | This object tells whether the port is connected to a host or to an interconnect (defined to be another NMM that is sending hello messages). The NMM agent will … |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.21 | Columns3EnetPortAddrCollect | read-write | mandatory | This object tells whether the NMM should collect node address information from this port for the Find Nodes, Show Nodes, and Traffic Matrix (NMM+ only) tables.… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.22 | Columns3EnetPortAddrLearnMode | read-write | mandatory | This object indicates whether the port should automatically learn the port address by reading the source address on the incoming packets. This object applies o… |
| 1.3.6.1.4.1.45.1.3.2.3.1.1.23 | Columns3EnetPortTxSecurity | read-write | mandatory | This value of this object is meaningful only when s3EnetConcSecureStatus is not set to concSecureOff(5) (i.e., if security features are activated on the concen… |
| 1.3.6.1.4.1.45.1.3.2.3.2 | Tables3EnetCommonPortTable | not-accessible | mandatory | This table provides a list of port entries. The number of entries is given for any Ethernet board in the concentrator, even if the board is not on the same Eth… |
| 1.3.6.1.4.1.45.1.3.2.3.2.1 | Rows3EnetCommonPortEntry | not-accessible | mandatory | A table containing objects about the ports of each Ethernet board plugged into the 3000-series chassis. |
| 1.3.6.1.4.1.45.1.3.2.3.2.1.1 | Columns3EnetCommonPortBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.2.3.2.1.2 | Columns3EnetCommonPortIndex | read-only | mandatory | A unique value for each port. Its value is dependent on the board type. |
| 1.3.6.1.4.1.45.1.3.2.3.2.1.3 | Columns3EnetCommonPortLinkStatus | read-only | mandatory | Tells whether the port is receiving link status. |
| 1.3.6.1.4.1.45.1.3.2.3.2.1.4 | Columns3EnetCommonPortPartStatus | read-write | mandatory | This indicates the operational status of the Port. Writing a partition(2) will partition the port indefinitely and enabled(1) will enable the port. If a timed … |
| 1.3.6.1.4.1.45.1.3.2.3.2.1.5 | Columns3EnetCommonPortType | read-only | mandatory | The media connnection type for this port. Note that this object was called s3EnetPortMDIXSwitch in the Ethernet 3.3 and 4.0 MIBs. |
| 1.3.6.1.4.1.45.1.3.2.3.2.1.6 | Columns3EnetCommonPortPartTime | read-write | mandatory | When partitioning the port for a specified time, s3EnetCommonPortPartStatus must be set with timedPartition(4) and this object must be supplied with the durati… |
| 1.3.6.1.4.1.45.1.3.2.3.3 | Tables3EnetRedPortTable | not-accessible | mandatory | A table of ports for each 10BASE-FL board with redundancy capability. The number of boards is determined by checking s3EnetCommonBoardRedund having a value of … |
| 1.3.6.1.4.1.45.1.3.2.3.3.1 | Rows3EnetRedPortEntry | not-accessible | mandatory | An entry in the table of ports on boards with redundancy capability. |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.1 | Columns3EnetRedPortBoardIndex | read-only | mandatory | The index of the slot containing the board. The value for each board must remain constant at least from one re-initialization of the entity's network managemen… |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.2 | Columns3EnetRedPortIndex | read-only | mandatory | The index of the port on the module. |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.3 | Columns3EnetRedPortRedundMode | read-only | mandatory | This object indicates the port's redundancy mode. A value of standAlone(1) indicates that the port is not set for hardware redundancy. A value of hwActive(2) i… |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.4 | Columns3EnetRedPortOperStatus | read-only | mandatory | This object indicates port's redundancy status. This value is valid only when the redundant mode is not standAlone(1). The values are: other(1).........none of… |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.5 | Columns3EnetRedPortRemoteOperStatus | read-only | mandatory | This object reflects the real time status of the received data from the remote port. A value of snpxFLRemFltCpblPortUp(1) indicates that the remote port is cap… |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.6 | Columns3EnetRedPortCompanionSlotNo | read-only | mandatory | The slot number of the other port which is in the redundant pair. In the case of a standalone port, a value of 0 will be returned. |
| 1.3.6.1.4.1.45.1.3.2.3.3.1.7 | Columns3EnetRedPortCompanionPortNo | read-only | mandatory | The port number of the other port which is in the redundant pair. In the case of a standalone port, a value of 0 will be returned. |
| 1.3.6.1.4.1.45.1.3.2.10 | Nodes3000EnetPlusStatistics | |||
| 1.3.6.1.4.1.45.1.3.2.10.1 | Tables3EnetPlusPortTable | not-accessible | mandatory | This table provides a list of entries, each entry providing information related to frame MAC level error conditions per port. This table is conceptually an ext… |
| 1.3.6.1.4.1.45.1.3.2.10.1.1 | Rows3EnetPlusPortEntry | not-accessible | mandatory | An entry in the Plus Port table. |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.1 | Columns3EnetPlusPortBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. (This is the slot number.) |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.2 | Columns3EnetPlusPortIndex | read-only | mandatory | A unique value for each port. Its value typically ranges between 1 and 12. |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.3 | Columns3EnetPortFragments | read-only | mandatory | This contains a count of fragments received by the board between 80-512 bits (64 bytes), inclusively, with invalid FCS or alignment errors. (These commonly rep… |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.4 | Columns3EnetPortShortEvents | read-only | mandatory | This contains a count of fragments received by the port shorter than 80 bits. |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.5 | Columns3EnetPortAutoPartitions | read-only | mandatory | This contains a count of times the ports on the board have autopartitioned due to excessive collisions (more than 32 consecutive collisions). This count is an … |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.6 | Columns3EnetPortRateMismatches | read-only | mandatory | This contains a count of the occurrences of out of spec bit rates. This indicates the number of times FIFO buffer over-runs or underruns due to transmission ra… |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.7 | Columns3EnetPortJabbers | read-only | mandatory | This contains a count of the times that MAU jabber lockup protection (MJLP) was invoked because transmission of data from this port exceeded 5 msec in duration… |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.8 | Columns3EnetPortLastSrcAddr | read-only | mandatory | This is the source address of the last packet received through this port. |
| 1.3.6.1.4.1.45.1.3.2.10.1.1.9 | Columns3EnetPortSrcAddrChanges | read-only | mandatory | This is the number of times that the s3EnetPortLastSrcAddr object for this has changed. |
| 1.3.6.1.4.1.45.1.3.2.10.2 | Tables3EnetPlusBoardTable | not-accessible | mandatory | This table provides a list of entries, each entry providing information related to frame MAC level error conditions per board. This table is conceptually an ex… |
| 1.3.6.1.4.1.45.1.3.2.10.2.1 | Rows3EnetPlusBoardEntry | not-accessible | mandatory | An entry in the Plus Board table. |
| 1.3.6.1.4.1.45.1.3.2.10.2.1.1 | Columns3EnetPlusBoardIndex | read-only | mandatory | The board number part of an index. |
| 1.3.6.1.4.1.45.1.3.2.10.2.1.2 | Columns3EnetBoardFragments | read-only | mandatory | This contains a count of fragments received by the board between 80-512 bits (64 bytes), inclusively, with invalid FCS or alignment errors. (These commonly rep… |
| 1.3.6.1.4.1.45.1.3.2.10.2.1.3 | Columns3EnetBoardShortEvents | read-only | mandatory | This contains a count of fragments received by the board shorter than 80 bits. |
| 1.3.6.1.4.1.45.1.3.2.10.2.1.4 | Columns3EnetBoardAutoPartitions | read-only | mandatory | This contains a count of times the ports on this board have been autopartitioned due to excessive collisions (more than 32 consecutive collisions). This count … |
| 1.3.6.1.4.1.45.1.3.2.10.2.1.5 | Columns3EnetBoardRateMismatches | read-only | mandatory | This contains a count of the occurrences of out of spec bit rates. This indicates the number of times FIFO buffer over-runs or underruns due to transmission ra… |
| 1.3.6.1.4.1.45.1.3.2.10.2.1.6 | Columns3EnetBoardJabbers | read-only | mandatory | This contains a count of the times that MAU jabber lockup protection (MJLP) was invoked because transmission of data from a port on this board exceeded 5 msec … |
| 1.3.6.1.4.1.45.1.3.2.10.3 | Nodes3000EnetPlusConc | |||
| 1.3.6.1.4.1.45.1.3.2.10.3.1 | Scalars3EnetConcShortEvents | read-only | mandatory | This contains a count of fragments received by the concentrator shorter than 80 bits. |
| 1.3.6.1.4.1.45.1.3.2.10.3.2 | Scalars3EnetConcAutoPartitions | read-only | mandatory | This contains a count of times the ports on this concentrator have been autopartitioned due to excessive collisions (more than 32 consecutive collisions). This… |
| 1.3.6.1.4.1.45.1.3.2.10.3.3 | Scalars3EnetConcRateMismatches | read-only | mandatory | This contains a count of the occurrences of out of spec bit rates. This indicates the number of times FIFO buffer over-runs or underruns due to transmission ra… |
| 1.3.6.1.4.1.45.1.3.2.10.3.4 | Scalars3EnetConcJabbers | read-only | mandatory | This contains a count of the times that MAU jabber lockup protection (MJLP) was invoked because transmission of data from a port on this concentrator exceeded … |
| 1.3.6.1.4.1.45.1.3.2.10.3.5 | Scalars3EnetConcCollBackoffErrors | read-only | mandatory | This contains a total concentrator count of the collision events that occur during the normal collision window (i.e., the collisions is not a late collision) a… |
| 1.3.6.1.4.1.45.1.3.3 | Nodes3000TokenRing | |||
| 1.3.6.1.4.1.45.1.3.3.2 | Nodes3000TrBoard | |||
| 1.3.6.1.4.1.45.1.3.3.2.2 | Tables3TrCommonBoardTable | not-accessible | mandatory | Information maintained for each token ring board. The information can be retrieved for any token ring board, even if the board is not on the same backplane rin… |
| 1.3.6.1.4.1.45.1.3.3.2.2.1 | Rows3TrCommonBoardEntry | not-accessible | mandatory | There is one entry per board in this table. |
| 1.3.6.1.4.1.45.1.3.3.2.2.1.1 | Columns3TrCommonBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.3.2.2.1.2 | Columns3TrCommonBoardRing1or2 | read-only | mandatory | Determines which ring the board is currently using on the concentrator backplane. |
| 1.3.6.1.4.1.45.1.3.3.2.2.1.3 | Columns3TrCommonBoardRingSpeed | read-only | mandatory | Token Ring speed of the ring that this board is connected to. |
| 1.3.6.1.4.1.45.1.3.3.3 | Nodes3000TrPort | |||
| 1.3.6.1.4.1.45.1.3.3.3.1 | Tables3TrPortTable | not-accessible | mandatory | A table containing information about each port of a LattisNet concentrator. The number of entries is given by knowing the number of occupied slots in s3Chassis… |
| 1.3.6.1.4.1.45.1.3.3.3.1.1 | Rows3TrPortEntry | not-accessible | mandatory | A port entry containing objects at the port level for a particular port. |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.1 | Columns3TrPortBoardIndex | read-only | mandatory | A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the enti… |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.2 | Columns3TrPortIndex | read-only | mandatory | A unique value for each port. Its value ranges between 1 and 12. The value for each port must remain constant at least from one re-initialization of the entity… |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.3 | Columns3TrPortWrap | read-write | mandatory | Status of the port. Setting wrap(2) disconnects the port from the ring and setting this object to connect(3) connects the port to the ring. If a timed wrap is … |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.4 | Columns3TrPortTestLatch | read-write | mandatory | Status of the test latch which is used to set the channel decoder used to monitor the health of the communication path between the NMM and the module channel. |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.5 | Columns3TrPortRelayStatus | read-only | mandatory | Status of the channel's present relay mode. On(2) means the channel is in the ring and off(3) means the channel is bypassed. |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.6 | Columns3TrPortPhantomStatus | read-only | mandatory | Status of the ring access request signal. |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.7 | Columns3TrPortPhantomChangeFlag | read-only | mandatory | Change(3) indicates that port phantom has been changed from OFF to ON. After inquiry by NMS, it will be cleared to noChange(2). Port phantom changing from ON t… |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.8 | Columns3TrPortChgSyn2IBM | read-write | mandatory | If the port is on a ring in/ring out module this object changes the strap state depending on the jumper setting retrieved as s3TrPortStrap. If the strap is set… |
| 1.3.6.1.4.1.45.1.3.3.3.1.1.9 | Columns3TrPortStrap | read-only | mandatory | If the port is on a ring in/ring out module this object signifies whether the hardware jumper is in synoptics(2) mode or ibm(3) mode. This information is retri… |
| 1.3.6.1.4.1.45.1.3.3.4 | Nodes3000TrNmm | |||
| 1.3.6.1.4.1.45.1.3.3.4.1 | Scalars3TrNmmFnNum | read-write | mandatory | Defines the flat network number that this NMM is part of. |
| 1.3.6.1.4.1.45.1.3.3.4.2 | Scalars3TrNmmRingNum | read-write | mandatory | Defines the segment number that this NMM is connected to. ***ACCESS VARIATION - changed access from read-only |
| 1.3.6.1.4.1.45.1.3.3.4.3 | Scalars3TrNmmSlotNum | read-only | deprecated | Defines the slot number that this NMM is connected to. New NMS implementations should use the object s3AgentMySlotId defined in the common MIB. This object wil… |
| 1.3.6.1.4.1.45.1.3.3.4.4 | Scalars3TrNmmFpuIdRev | read-only | mandatory | The revision of the Front-end Frame Processing unit. 0=Rev. A, 1=Rev. B, etc. |
| 1.3.6.1.4.1.45.1.3.3.4.5 | Scalars3TrNmmFpuStatus | read-only | mandatory | The status of the Front-end Frame Processing Unit. |
| 1.3.6.1.4.1.45.1.3.3.4.6 | Scalars3TrNmmDramSize | read-only | mandatory | The highest address of the DRAM in the NMM memory map. The possible values are: other(1).........Unknown size k512(2)..........512K memory oneMeg(3)........1M … |
| 1.3.6.1.4.1.45.1.3.3.4.7 | Scalars3TrNmmEepromSize | read-only | mandatory | The size of the EEPROM in the NMM memory map. The possible values are: other(1)..........Unknown size size2kBytes(4)....2K by 8 size8kBytes(4)....8K by 8 size1… |
| 1.3.6.1.4.1.45.1.3.3.4.8 | Scalars3TrNmmGrpAddrFrmsRxOk | read-only | mandatory | Number of Group Address frames received without error by this NMM. Note: The NMM counts only Group Address frames that are addressed to its own Group Address(e… |
| 1.3.6.1.4.1.45.1.3.3.4.9 | Scalars3TrNmmRing1or2 | read-only | mandatory | Determines which ring the NMM is currently using on the concentrator backplane. |
| 1.3.6.1.4.1.45.1.3.3.4.10 | Scalars3TrNmmRingSpeed | read-only | mandatory | Token Ring speed. |
| 1.3.6.1.4.1.45.1.3.3.4.11 | Scalars3TrNmmHexDisplay | read-only | mandatory | 4 octet hex display string that is displayed on the NMM control panel. |
| 1.3.6.1.4.1.45.1.3.3.4.12 | Scalars3TrNmmEpromSize | read-only | mandatory | The size of the EPROM in the NMM memory map. |
| 1.3.6.1.4.1.45.1.3.3.5 | Nodes3000TrNode | |||
| 1.3.6.1.4.1.45.1.3.3.5.1 | Tables3TrNodeTable | not-accessible | mandatory | Table containing station specific information. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1 | Rows3TrNodeEntry | not-accessible | mandatory | Entry in the table containing counters and profiling information for each node detected on the local token ring. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.1 | Columns3TrNodeEntMacAddress | read-only | mandatory | MAC address of node that this entry in the table is for. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.4 | Columns3TrNodeEntStatus | read-only | mandatory | Tells whether the station is currently beaconing or not. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.5 | Columns3TrNodeEntNodeStatus | read-only | mandatory | Node status as defined in 802.5 specification (section 3.3.2.18). |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.6 | Columns3TrNodeLineErrs | read-only | mandatory | Number of line errors. Section 3.8.1 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.7 | Columns3TrNodeBurstErrs | read-only | mandatory | Number of burst errors. Section 3.8.3 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.8 | Columns3TrNodeAriFciErrs | read-only | mandatory | Number of ARI FCI errors. See AC errors, Section 3.8.4 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.9 | Columns3TrNodeLostFrames | read-only | mandatory | Number of frames lost. Section 3.8.6 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.10 | Columns3TrNodeRcvCongestErrs | read-only | mandatory | Number of receive congestion errors. Section 3.8.7 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.11 | Columns3TrNodeFrmCopyErrs | read-only | mandatory | Number of frame copy errors. Section 3.8.8 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.12 | Columns3TrNodeTokenErrs | read-only | mandatory | Number of token errors. Section 3.8.10 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.13 | Columns3TrNodeInternalErrs | read-only | mandatory | Number of internal errors. Section 3.8.2 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.14 | Columns3TrNodeAbortTransErrs | read-only | mandatory | Number of abort delimiter transmitted errors. Section 3.8.5 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.15 | Columns3TrNodeFrequencyErrs | read-only | mandatory | Number of frequency errors. Section 3.8.9 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.16 | Columns3TrNodeEntProductId | read-only | mandatory | A brief string describing the product specified by the vendor. Section 3.3.2.14 of IEEE 802.5 specification. The characters in the string are represented in EB… |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.17 | Columns3TrNodeEntUna | read-only | mandatory | The Upstream Neighbor Address. Section 3.3.2.15 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.18 | Columns3TrNodeEntNodeVersion | read-only | mandatory | String that represents the version of the station software. Section 3.3.2.17 of IEEE 802.5 specification. The characters in the string are represented in EBCDI… |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.19 | Columns3TrNodeEntPhysDrop | read-only | mandatory | This reports the physical location of this node on the ring. Section 3.3.2.13 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.20 | Columns3TrNodeEntFuncAddr | read-only | mandatory | Specifies the functional addresses used by this station. Section 3.3.2.8 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.21 | Columns3TrNodeEntAuthFuncClass | read-only | mandatory | This specifies the functional classes that are allowed to be active in the station. Section 3.3.2.3 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.22 | Columns3TrNodeEntAuthAccPriority | read-only | mandatory | The maximum priority this station is allowed to use. Section 3.3.2.2 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.23 | Columns3TrNodeEntGrpAddr | read-only | mandatory | This contains the group address of this station. Section 3.3.2.9 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.24 | Columns3TrNodeEntStationId | read-only | mandatory | This string is used to uniquely identify the station. It may be equal to the station's MAC address. Section 3.3.2.21 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.25 | Columns3TrNodeEntBeaconType | read-only | mandatory | This specifies the type of beacon frame seen. Section 3.3.2.4 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.26 | Columns3TrNodeBeaconCnt | read-only | mandatory | Number of beacon frames that have been sent by this station. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.27 | Columns3TrNodeLastBeaconTime | read-only | mandatory | The time of the last beacon frame sent by this station. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.28 | Columns3TrNodeLastInsertTime | read-only | mandatory | The time of the last ring insertion by this station. Time is relative from the system uptime. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.29 | Columns3TrNodeFirstInsertTime | read-only | mandatory | The time of the first ring insertion by this station. Time is relative from the system uptime. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.30 | Columns3TrNodeLastDeinsertTime | read-only | mandatory | The time of the last ring deinsertion by this station. Time is relative from the system uptime. |
| 1.3.6.1.4.1.45.1.3.3.5.1.1.31 | Columns3TrNodeRemoveStation | read-write | mandatory | Removes the MAC address associated with this entry from the ring by sending a REMOVE MAC frame if this object is written to with remove(2). |
| 1.3.6.1.4.1.45.1.3.3.7 | Nodes3000TrRing | |||
| 1.3.6.1.4.1.45.1.3.3.7.1 | Nodes3TrRingStats | |||
| 1.3.6.1.4.1.45.1.3.3.7.1.1 | Scalars3TrRingStatus | read-only | mandatory | The status of the ring. |
| 1.3.6.1.4.1.45.1.3.3.7.1.2 | Scalars3TrRingFrmsRxOk | read-only | mandatory | Number of frames received successfully by the NMM. |
| 1.3.6.1.4.1.45.1.3.3.7.1.3 | Scalars3TrRingOctetsRxOk | read-only | mandatory | Number of octets received successfully by the NMM. |
| 1.3.6.1.4.1.45.1.3.3.7.1.4 | Scalars3TrRingBcastFrmsRxOk | read-only | mandatory | Number of broadcast frames received successfully by the NMM. |
| 1.3.6.1.4.1.45.1.3.3.7.1.5 | Scalars3TrRingLineErrs | read-only | mandatory | Number of line errors. Section 3.8.1 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.6 | Scalars3TrRingBurstErrs | read-only | mandatory | Number of burst errors. Section 3.8.3 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.7 | Scalars3TrRingAriFciErrs | read-only | mandatory | Number of ARI FCI errors. See AC errors, Section 3.8.4 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.8 | Scalars3TrRingLostFrames | read-only | mandatory | Number of frames lost. Section 3.8.6 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.9 | Scalars3TrRingRcvCongestErrs | read-only | mandatory | Number of receive congestion errors. Section 3.8.7 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.10 | Scalars3TrRingFrmCopyErrs | read-only | mandatory | Number of frame copy errors. Section 3.8.8 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.11 | Scalars3TrRingTokenErrs | read-only | mandatory | Number of token errors. Section 3.8.10 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.12 | Scalars3TrRingInternalErrs | read-only | mandatory | Number of internal errors. Section 3.8.2 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.13 | Scalars3TrRingAbortTransErrs | read-only | mandatory | Number of abort delimiter transmitted errors. Section 3.8.5 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.14 | Scalars3TrRingFrequencyErrs | read-only | mandatory | Number of frequency errors. Section 3.8.9 of IEEE 802.5 specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.15 | Scalars3TrRingBeaconCnt | read-only | mandatory | Number of beacon frames that have been seen. |
| 1.3.6.1.4.1.45.1.3.3.7.1.16 | Scalars3TrRingBeaconType | read-only | mandatory | This specifies the type of beacon frame seen. Section 3.3.2.4 of IEEE 802.5 Specification. |
| 1.3.6.1.4.1.45.1.3.3.7.1.17 | Scalars3TrRingLastBeaconTime | read-only | mandatory | The time of the last beacon frame sent on the ring. Time is relative from the system uptime. |
| 1.3.6.1.4.1.45.1.3.3.7.1.18 | Scalars3TrRingBeaconStation | read-only | mandatory | The MAC address of station last beaconing. |
| 1.3.6.1.4.1.45.2 | Nodetemporary | |||
| 1.3.6.1.4.1.45.2.1 | Nodeieee8023 | |||
| 1.3.6.1.4.1.45.2.1.1 | Tableieee8023IfTable | not-accessible | mandatory | Statistics for a list of interface entries. There is one entry per IEEE 802.3 like 'interface.' |
| 1.3.6.1.4.1.45.2.1.1.1 | Rowieee8023IfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.45.2.1.1.1.1 | Columnieee8023IfIndex | read-only | mandatory | Index of the interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| 1.3.6.1.4.1.45.2.1.1.1.2 | Columnieee8023FrmsTxOk | read-only | mandatory | The number of frames that are successfully transmitted. This counter is incremented when a frame is successfully transmitted, even if one of the collision coun… |
| 1.3.6.1.4.1.45.2.1.1.1.3 | Columnieee8023SingleCollFrms | read-only | mandatory | The number of frames that are involved in a single collision, and are subsequently transmitted successfully. If this counter is incremented, then the ieee8023F… |
| 1.3.6.1.4.1.45.2.1.1.1.4 | Columnieee8023MultipleCollFrms | read-only | mandatory | The number of frames that are involved in more than one collision and are subsequently transmitted successfully. If this counter is incremented, then the ieee8… |
| 1.3.6.1.4.1.45.2.1.1.1.5 | Columnieee8023OctetsTxOk | read-only | mandatory | The amount of data AND PADDING octets of frames that are successfully transmitted. This counter includes octets in broadcast and multicast frames that are tran… |
| 1.3.6.1.4.1.45.2.1.1.1.6 | Columnieee8023DefTx | read-only | mandatory | The number of frames whose transmission was delayed on its first attempt because the medium was busy. Frames involved in collisions are NOT included in this co… |
| 1.3.6.1.4.1.45.2.1.1.1.7 | Columnieee8023McastFrmsTxOk | read-only | mandatory | The number of frames successfully transmitted to a multicast address. This counter does not include frames sent to the broadcast address. |
| 1.3.6.1.4.1.45.2.1.1.1.8 | Columnieee8023BcastFrmsTxOk | read-only | mandatory | The number of frames successfully transmitted to the broadcast address. This counter does not include frames sent to a multicast address. |
| 1.3.6.1.4.1.45.2.1.1.1.9 | Columnieee8023LateColls | read-only | mandatory | The number of times that a collision has been detected later than 512 bit times into the transmission of a packet. 512 bit times is 51.2 micro secs. This type … |
| 1.3.6.1.4.1.45.2.1.1.1.10 | Columnieee8023ExcessColls | read-only | mandatory | The number of frames that are not transmitted because of excessive collisions. |
| 1.3.6.1.4.1.45.2.1.1.1.11 | Columnieee8023IntlMacTxError | read-only | mandatory | The number of frames that would otherwise be transmitted by the station, but could not be sent because of an internal MAC sublayer transmit error. If this coun… |
| 1.3.6.1.4.1.45.2.1.1.1.12 | Columnieee8023CsErrors | read-only | mandatory | The number of times that carrier sense was lost or never appeared when attempting to transmit a packet. This counter is incremented ONCE per transmission attem… |
| 1.3.6.1.4.1.45.2.1.1.1.13 | Columnieee8023ExcessDef | read-only | mandatory | The number of frames that deferred for an excessive period of time. |
| 1.3.6.1.4.1.45.2.1.1.1.14 | Columnieee8023FrmsRxOk | read-only | mandatory | The number of frames that are successfully received. This counter does not include frames received with frame-too-long, FCS, length, or alignment errors, or fr… |
| 1.3.6.1.4.1.45.2.1.1.1.15 | Columnieee8023OctetsRxOk | read-only | mandatory | The number entry of data and padding octets in frames that are successfully received. This counter does not include frames received with frame-too-long, FCS, l… |
| 1.3.6.1.4.1.45.2.1.1.1.16 | Columnieee8023McastFrmsRxOk | read-only | mandatory | The number of frames that are successfully received and are directed to an active non-broadcast group address. This counter does not include frames received wi… |
| 1.3.6.1.4.1.45.2.1.1.1.17 | Columnieee8023BcastFrmsRxOk | read-only | mandatory | The number of frames that are successfully received and are directed to the broadcast group address. This counter does not include frames received with frame-t… |
| 1.3.6.1.4.1.45.2.1.1.1.18 | Columnieee8023TooLongErrors | read-only | mandatory | The number of frames that are received and exceed the maximum permitted frame size. This counter is incremented when the frameTooLong error is returned. |
| 1.3.6.1.4.1.45.2.1.1.1.19 | Columnieee8023AlignErrors | read-only | mandatory | The number of frames that are not an integral number of octets in length and do not pass the FCS check. This counter is incremented when the alignmentError sta… |
| 1.3.6.1.4.1.45.2.1.1.1.20 | Columnieee8023FcsErrors | read-only | mandatory | The number of frames that are an integral number of octets in length and do not pass the FCS check. This counter is incremented when the frameCheckError status… |
| 1.3.6.1.4.1.45.2.1.1.1.21 | Columnieee8023IrLengthErrors | read-only | mandatory | The number of frames with a length field value between the minimum unpadded LLC data size and the maximum allowed LLC data size inclusive, and which do not mat… |
| 1.3.6.1.4.1.45.2.1.1.1.22 | Columnieee8023OorLengthFields | read-only | mandatory | The number of frames with a length field value greater than the maximum allowed LLC data size. If true 802.3 is followed for layer management, then this counte… |
| 1.3.6.1.4.1.45.2.1.1.1.23 | Columnieee8023IntlMacRxErrors | read-only | mandatory | The number of frames that would otherwise be received by the station, but could not be accepted because of an internal MAC sublayer receive error. If this coun… |
| 1.3.6.1.4.1.45.2.1.1.1.24 | Columnieee8023InitMac | read-write | mandatory | Reinitializes the MAC and PLS (physical layer signaling). All MIB counters are set to 0. The states of the status variables (described below) are as follows: -… |
| 1.3.6.1.4.1.45.2.1.1.1.25 | Columnieee8023PromRxStatus | read-write | mandatory | This variable combines the enable ieee8023PromRx, disable ieee8023PromRx, and read ieee8023PromStatus MAC actions. Setting this variable to enabled causes the … |
| 1.3.6.1.4.1.45.2.1.1.1.26 | Columnieee8023MacSubLayerStatus | read-write | mandatory | This variable causes the MAC sublayer to enter the normal operational state at idle. The PLS is reset by this operation. It is accomplished by setting receiveE… |
| 1.3.6.1.4.1.45.2.1.1.1.27 | Columnieee8023TxStatus | read-write | mandatory | This variable enables the MAC sublayer to be explicitly enabled/disabled for transmitting frames. If a frame is being transmitted when this variable is set to … |
| 1.3.6.1.4.1.45.2.1.1.1.28 | Columnieee8023McastRxStatus | read-write | mandatory | Enables/disables reception of multicast frames. To actually receive multicasts, both this variable AND ieee8023MacSubLayerStatus must be set to enabled. |
| 1.3.6.1.4.1.45.2.1.1.1.29 | Columnieee8023MacAddress | read-write | mandatory | This object contains the MAC station address (i.e., the Ethernet address). |
| 1.3.6.1.4.1.45.2.1.1.1.30 | Columnieee8023SqeTestErrors | read-only | mandatory | The number of times that the SQE TEST ERROR status was received. |
| 1.3.6.1.4.1.45.2.1.2 | Tableieee8023CollTable | not-accessible | mandatory | A table containing information on collision activity. |
| 1.3.6.1.4.1.45.2.1.2.1 | Rowieee8023CollEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.45.2.1.2.1.1 | Columnieee8023CollRetrans | read-only | mandatory | The entry corresponding to the number of attempts made before a frame was successfully transmitted. The range is from 1 to 15. |
| 1.3.6.1.4.1.45.2.1.2.1.2 | Columnieee8023CollIndex | read-only | mandatory | The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the s… |
| 1.3.6.1.4.1.45.2.1.2.1.3 | Columnieee8023Collisions | read-only | mandatory | The number of frames that were retransmitted a specific number of times. |
| 1.3.6.1.4.1.45.2.1.3 | Tableieee8023GroupTable | not-accessible | mandatory | A table containing information on group addresses. There are five entries in the table. |
| 1.3.6.1.4.1.45.2.1.3.1 | Rowieee8023GroupEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.45.2.1.3.1.1 | Columnieee8023GroupIndex | read-only | mandatory | The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the s… |
| 1.3.6.1.4.1.45.2.1.3.1.2 | Columnieee8023GroupAddress | read-write | mandatory | A group address to which this Ethernet-like interface responds. ***ACCESS VARIATION - changed access from read-only |
| 1.3.6.1.4.1.45.2.1.3.1.3 | Columnieee8023GroupType | read-write | mandatory | Type of group address. Setting this object to the value invalid(2) invalidates the corresponding entry in the ieee8023GroupTable. That is, it effectively disas… |
| 1.3.6.1.4.1.45.3 | Noderegistration | |||
| 1.3.6.1.4.1.45.3.2 | Nodes3reg-3000 | |||
| 1.3.6.1.4.1.45.3.2.1 | Nodes3reg-3000-enetNMM | |||
| 1.3.6.1.4.1.45.3.2.2 | Nodes3reg-3000-trNMM | |||
| 1.3.6.1.4.1.45.3.3 | Nodes3reg-3030 | |||
| 1.3.6.1.4.1.45.3.3.1 | Nodes3reg-3030-enetNMM | |||
| 1.3.6.1.4.1.45.3.3.2 | Nodes3reg-3030-trNMM | |||
| 1.3.6.1.4.1.45.3.9 | Nodes3reg-2715 | |||
| 1.3.6.1.4.1.45.3.9.1 | Nodes3reg-2715-trNMM | |||
| 1.3.6.1.4.1.45.3.12 | Nodes3reg-281X | |||
| 1.3.6.1.4.1.45.3.12.1 | Nodes3reg-281X-enetNMM | |||
| 1.3.6.1.4.1.45.4 | NodeportAutoPartition | Port auto partitions (wraps). | ||
| 1.3.6.1.4.1.45.5 | NodeportDTEJabbering | Ethernet DTE jabbering detected. | ||
| 1.3.6.1.4.1.45.8 | NodelocalBridgeDiagnostic | NMM detects bridge failure. | ||
| 1.3.6.1.4.1.45.9 | NoderemoteBridgePortOperationChanged | Bridge changes from standby <-> operation. | ||
| 1.3.6.1.4.1.45.10 | NoderemoteBridgeDiagnostic | NMM detects remote bridge failure. | ||
| 1.3.6.1.4.1.45.11 | NodeboardLEDFailure | Board is on but LED is off. | ||
| 1.3.6.1.4.1.45.27 | NodeboardPowerSupplyFailure | Board power supply failure. | ||
| 1.3.6.1.4.1.45.30 | NodelocalBridgeOperationChanged | Bridge changes from standby <-> operation. | ||
| 1.3.6.1.4.1.45.31 | NoderemoteBridgeOperationChanged | Bridge changes from standby <-> operation. | ||
| 1.3.6.1.4.1.45.33 | NoderouterOperationChanged | Router changes from standby <-> operation. | ||
| 1.3.6.1.4.1.45.34 | NoderouterDiagnostic | NMM detects router failure. | ||
| 1.3.6.1.4.1.45.35 | NodekeyManagementFailure | NMM detects that its key doesn't match the configuration. | ||
| 1.3.6.1.4.1.45.44 | NodenmmSaturationA | NMM is dropping packets due to overload. | ||
| 1.3.6.1.4.1.45.46 | NodelattisSecureInitRequired | This trap is sent by a 331xS Ethernet NMM+ when a LattisSecure Host Module needs initialization. The location of the module is indicated by the instance identi… | ||
| 1.3.6.1.4.1.45.47 | NoderedPsPlus5vCurrentExceed | This trap is sent when the current level on the +5 V supply exceeds the maximum recommended level: 1) 30 amps if at least one of the power supplies is a 3001. … | ||
| 1.3.6.1.4.1.45.48 | NoderedPsPlus12vCurrentExceed | This trap is sent when the current level on the +12 V supply exceeds the maximum recommended level of 15 amps for any set of power supplies. Note: The agent re… | ||
| 1.3.6.1.4.1.45.49 | NoderedPsAmbientTempStatChg | This trap is sent whenever there is a change (in either direction) in the psAmbientTempStatus variable. | ||
| 1.3.6.1.4.1.45.50 | NoderedPsSummingDiodeFailure | This trap is sent whenever the reported status of either 3100R summing diode changes from 'Ok' to 'Fail'. | ||
| 1.3.6.1.4.1.45.51 | NodeboardSwap | This trap is sent whenever a board is inserted or removed. The values returned are those before the action was taken. Thus, the value of s3SlotModuleType will … | ||
| 1.3.6.1.4.1.45.53 | NodeenetChannelChange | This trap is sent whenever a board is switched from one channel to the other. The value returned is the one before the action was taken. Thus, the value of s3E… | ||
| 1.3.6.1.4.1.45.54 | NodeflashUpdateFailure | This trap is sent whenever the agent failed to update the local image due to flash device failure. | ||
| 1.3.6.1.4.1.45.58 | NoderedundPortSwitchover | This trap is sent whenever NMM detects a redundant port pair switchover. The values returned are those after the action was taken. The instance values (slot.po… | ||
| 1.3.6.1.4.1.45.59 | NoderedundBadRemCfgDetected | This trap is sent periodically when the NMM detects a s3EnetRedPortRemoteOperStatus of flidl(3) on a port set for hardware redundancy. The trap is also sent wh… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING | ||
| IpxAddress | OCTET STRING (SIZE(10)) | ||
| PhysAddress | OCTET STRING | ||
| S3ModuleType | INTEGER { empty(1), other(2), m3302(3), m3304-ST(4), m3305(5), m3308(6), m3313(7), m3313M(8), m3314-ST(9), m3314M-ST(10), m3323(11), m3324-ST(12), m3502(13), m3532(14), m3552(15), m3301(16), m3307(17), m3356(18), m3512(19), m3514(20), m3505(21), m3554(22), m3534(23), m3383(24), m3384(25), m331x(26), m351x(27), m3502-A(28), m3902(29), m3904(30), m3910S(31), m3386(32), m3394(33), m3395(34), m3323S(35), m3324S-ST(36), m3307A(37), m3308A(38), m3505A(39), m3513(40), m3333(41), m3334-ST(42), m3040(43), m3100R(44), notUsed45(45), notUsed46(46), m2810-hm(47), m2810-nmm(48), m3313S(49), m3314S(50), m3368(51), m3512S(52), m3513S(53), m3514S(54), m3522(55), m2912(56), m2914(57), notUsed58(58), m3301-75(59), m3301-93(60), m271x-nmm(61), m2705-hm(62), m2715-hm(63), m2813-nmm(64), m2814-nmm(65), m2813-hm(66), m2814-hm(67), m2803-hm(68), m2804-hm(69), m3395A(70), m3040S(71), m3502B(72), m3505B(73), m2715-F-hm(74), m2712-hm(75), m2712-F-hm(76), m2702-hm(77), m2702-C-hm(78), m2705-F-hm(79), m2702-F-hm(80), m2705-C-hm(81), m3902A(82), m2912A(83), m3313A(84), m3314A(85), m3307HD(86), m3328(87), m3904-2SM(88), m3910S-SM(89), m3800(90), m3910S-SD(91), m3904-4SM(92), m2915(93), m3910SA(94), m3910SA-SM(95), m3905(96), m2715B-hm(97), m2705B-hm(98), m2715B-F-hm(99), m2712B-hm(100), m2712B-F-hm(101), m2702B-C-hm(102), m3304A(103), m3486(104), m3308B(105), m2813SA-nmm(106), m2814SA-nmm(107), m3517SA(108), m810M(109), m3313SA(110), m3314SA(111), m3522A(112), m3504-ST(113), m3513SA(114), mAlcatel-Eth-nmm(115), mAlcatel-Eth-hm1(116), mAlcatel-Eth-hm(117), m2486-nmm(118), m2486-hm(119), m3174(120), m271xSA-nmm(121), m3299C(122), m3299U(123), m3299F(124) } | ||
| S3PsType | INTEGER { other(1), low(2), medium(3), high(4), redundantCapable(5), empty(6) } | ||
| SnpxBackplaneType | INTEGER { other(1), eth(2), ethTok(3), ethFddi(4), ethTokFddi(5), ethTokRed(6), ethTokFddiRed(7), tok(8) } | ||
| SnpxChassisType | INTEGER { other(1), m3000(2), m3030(3), m2310(4), m2810(5), m2912(6), m2914(7), m271x(8), m2813(9), m2814(10), m2915(11), m5000(12), m2813SA(13), m2814SA(14), m810M(15), m1032x(16), m5005(17), mAlcatelEthConc(18), m2715SA(20), m2486(21) } |