MIB Viewer

TAIT-INFRA93SERIES-MIB

266 objects
rctRfTransmitter, rctRfReceiver, rctSelectedChannel related Monitored values in the TB93XX series Base Stations
Imported Objects
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE OBJECT-GROUP
SNMPv2-SMICounter32 MODULE-IDENTITY OBJECT-TYPE Unsigned32
SNMPv2-TCDisplayString TruthValue
TAIT-COMMON-MIBtaitGeneric
TAIT-INFRA93-94SERIES-COMMON-MIBinfra93-94MibModule
TAIT-INFRA93-94SERIES-TC-MIBAlarmState BaseStationMode ChannelGroupStatus Condition CurrentmA FrequencyHz GateState Milliseconds OptionState PowerW TimingControlType TransmitterStatus VoltageV
TAIT-INFRA93SERIES-TC-MIBColourCode ControlProtocolStatus DcsCode FallbackNodeStatus FrequencydHz LeveldBm LogicalChannelState MPTControlProtocolStatus OperationalMode Ratio ReceiverSyncStatus RxFrequencyResponse SINADLevel StandaloneNodeStatus SubAudibleType Temperature TransmitterSyncStatus TxFrequencyResponse
OIDNameAccessStatusDescription
1.3.6.1.4.1.3570.1.1.10.2Identityinfra93MibMonitoredentiresrctRfTransmitter, rctRfReceiver, rctSelectedChannel related Monitored values in the TB93XX series Base Stations
1.3.6.1.4.1.3570.2.2Nodeinfra93MIB
1.3.6.1.4.1.3570.2.2.2Nodemonitored
1.3.6.1.4.1.3570.2.2.2.1NodemibObjects
1.3.6.1.4.1.3570.2.2.2.1.1NodeproductInfo
1.3.6.1.4.1.3570.2.2.2.1.1.1NodeproductSummary
1.3.6.1.4.1.3570.2.2.2.1.1.1.1Nodeinfo
1.3.6.1.4.1.3570.2.2.2.1.1.1.1.1ScalarinfoTransmitterStatusread-onlycurrentThe current status of the transmitter. unknown(0): The transmitter is in an unknown, probably faulty state. unconfigured(1): The transmitter requires configura…
1.3.6.1.4.1.3570.2.2.2.1.1.1.1.2ScalarinfoStandaloneNodeStatusread-onlydeprecatedThe current status of standalone mode. offline(0): A maintainer has taken the base station offline. The base station is not under node control. standby(1): The…
1.3.6.1.4.1.3570.2.2.2.1.1.1.1.3ScalarinfoMPTFallbackNodeStatusread-onlycurrentThe current status of the MPT fallback node.
1.3.6.1.4.1.3570.2.2.2.1.1.1.1.4ScalarinfoDMRFallbackNodeStatusread-onlycurrentThe current status of the DMR fallback node.
1.3.6.1.4.1.3570.2.2.2.1.1.1.2Nodehealth
1.3.6.1.4.1.3570.2.2.2.1.1.1.2.2ScalarhealthRunModeread-onlycurrentIndicates the current base station mode. Offline means that a maintainer has taken the base station out of service. offline(0): The base station is currently o…
1.3.6.1.4.1.3570.2.2.2.1.1.1.2.3ScalarhealthNetworkConnLogChan1Stateread-onlycurrentIndicates the state of logical channel 1. inactive(0): The logical channel is not transmitting. idle(1): The logical channel is currently idle. It is not curre…
1.3.6.1.4.1.3570.2.2.2.1.1.1.2.4ScalarhealthNetworkConnLogChan2Stateread-onlycurrentIndicates the state of logical channel 2. inactive(0): The logical channel is not transmitting. idle(1): The logical channel is currently idle. It is not curre…
1.3.6.1.4.1.3570.2.2.2.1.1.1.2.5ScalarhealthSecureShellRunningread-onlycurrentIndicates whether the remote secure shell interface is running. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2NodeproductEnabledFeatures
1.3.6.1.4.1.3570.2.2.2.1.1.2.300ScalarlicenceDmrFullread-onlycurrentDMR Full license. The base station is licensed for operation on a DMR Full system. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.301ScalarlicenceAnalogConventionalread-onlycurrentAnalog Conventional licence. The base station is licenced for Analog conventional operation Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.302ScalarlicenceDmrExpressread-onlycurrentDMR Express 6 license. The base station is licensed for operation on a DMR Express system. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.303ScalarlicenceDmrAccessread-onlycurrentDMR Access license. The base station is licensed for operation on a DMR Access system. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.304ScalarlicenceDmrConventionalread-onlycurrentDMR Conventional license. The base station is licensed for operation on a DMR concentional system. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.305ScalarlicenceDmrExpress20read-onlycurrentDMR Express 20 license. The base station is licensed for operation on a DMR Express 20 system. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.306ScalarlicenceDmrCentralVoterread-onlycurrentDMR Central Voter license. The base station is licensed for operation as a DMR Central Voter. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.1.2.307ScalarlicenceDmrNetworkSatelliteread-onlycurrentDMR IP Networking Satellite license. The base station is licensed for operation as a DMR IP Networking satellite. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.2Nodemodules
1.3.6.1.4.1.3570.2.2.2.1.2.2Nodereciter
1.3.6.1.4.1.3570.2.2.2.1.2.2.1NoderctSummary
1.3.6.1.4.1.3570.2.2.2.1.2.2.1.1NoderctInfo
1.3.6.1.4.1.3570.2.2.2.1.2.2.1.1.1ScalarrctInfoProductCoderead-onlycurrentThe reciter product code. Product codes are explained in the Specifications Manual.
1.3.6.1.4.1.3570.2.2.2.1.2.2.1.1.2ScalarrctInfoSerialNumberread-onlycurrentThe reciter serial number. A unique identifier assigned to the module in the factory.
1.3.6.1.4.1.3570.2.2.2.1.2.2.1.1.3ScalarrctInfoHardwareVersionread-onlycurrentThe reciter hardware version number.
1.3.6.1.4.1.3570.2.2.2.1.2.2.1.1.4ScalarrctInfoFirmwareVersionread-onlycurrentThe version number of the firmware currently installed on the Reciter.
1.3.6.1.4.1.3570.2.2.2.1.2.2.1.2NoderctHealth
1.3.6.1.4.1.3570.2.2.2.1.2.2.2NoderctSelectedChannel
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.1ScalarrctSelectedChannelNumberread-onlycurrentNumber of the currently selected channel. Range: 1..1000
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.2ScalarrctSelectedChannelNameread-onlycurrentName of the current channel.
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.3ScalarrctSelectedChannelProfileNameread-onlycurrentName of the channel profile assigned to the currently selected channel.
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.4ScalarrctSelectedChannelSigProfileNameread-onlycurrentName of the signalling profile assigned to the currently selected channel.
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.5ScalarrctSelectedChannelTransmitPowerread-onlycurrentConfigured PA RF transmit power in watts for the current channel when it is powered by mains. Range: 0..100
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.6ScalarrctSelectedChannelTxFreqread-onlycurrentThe transmit frequency of the current channel in Hz. Range: 100000000..1000000000
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.7ScalarrctSelectedChannelRxFreqread-onlycurrentThe receive frequency of the current channel in Hz. Range: 100000000..1000000000
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.10ScalarrctSelectedChannelSystemTyperead-onlycurrentThe type of network configured in the channel profile of the currently selected channel, analogConventional(1), dmrConventional(2), dmrTrunking(3), mptTrunking…
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.11ScalarrctSelectedChannelColourCoderead-onlycurrentThe configured colour code for the currently selected channel
1.3.6.1.4.1.3570.2.2.2.1.2.2.2.12ScalarrctSelectedChannelGroupNameread-onlycurrentName of the channel group assigned to the currently selected channel.
1.3.6.1.4.1.3570.2.2.2.1.2.2.3NoderctRfReceiveQuality
1.3.6.1.4.1.3570.2.2.2.1.2.2.3.2ScalarrctRfRcvInterferenceread-onlycurrentInterference level is above configured RSSI threshold. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.2.2.3.3ScalarrctRfInterferenceCounterread-onlycurrentCounter indicating cumulative number of seconds that interference has been present. Range: 0..4294967295
1.3.6.1.4.1.3570.2.2.2.1.2.2.3.4ScalarrctRfInterferenceEventsread-onlycurrentThe number of times the receiver detects interference.
1.3.6.1.4.1.3570.2.2.2.1.2.2.4NoderctRfReceiver
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.1ScalarrctRfReceiverRSSIread-onlycurrentThe current strength of the received signal in dBm. Range: -12000..-6000
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.2ScalarrctRfReceiverLC1RSSIread-onlycurrentThe current strength of the received signal on logical channel 1 in dBm. Range: -12000..-6000
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.3ScalarrctRfReceiverLC2RSSIread-onlycurrentThe current strength of the received signal on logical channel 2 in dBm. Range: -12000..-6000
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.4ScalarrctRfReceiverLC1RxGateStateread-onlycurrentReceiver gate state of logical channel 1. Only valid if the logical channel has received anything since powering up. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.5ScalarrctRfReceiverLC2RxGateStateread-onlycurrentReceiver gate state of logical channel 2. Only valid if the logical channel has received anything since powering up. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.8ScalarrctRfReceiverSelectedDecodeCTCSSread-onlycurrentThe CTCSS value that the base station unmutes to.
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.9ScalarrctRfReceiverSelectedDecodeSubAudibleTyperead-onlycurrentThe configured receive sub-audible signaling type.
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.10ScalarrctRfReceiverSelectedSINADGatingLevelread-onlycurrentThe configured signal-to-noise gating threshold in dB.
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.11ScalarrctRfReceiverSelectedDecodeDCSread-onlycurrentThe DCS value that the base station unmutes to.
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.12ScalarrctRfReceiverSelectedFrequencyResponseread-onlycurrentSpecifies the receive baseband frequency response that applies to the channel. MPT Control channels have a flat speech charactieristic. MPT Traffic channels ha…
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.13ScalarrctRfReceiverAnalogGateStateread-onlycurrentAnalog receiver gate state of the channel. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.2.2.4.14ScalarrctRfReceiverIsDisabledread-onlycurrentStatus of the receiver; if it is unavailable then the receiver can't be disabled in the current mode of operation. Range: true(1), false(2)
1.3.6.1.4.1.3570.2.2.2.1.2.2.5NoderctRfTransmitter
1.3.6.1.4.1.3570.2.2.2.1.2.2.5.10ScalarrctRfTxSelectedEncodeCTCSSread-onlycurrentThe configured transmit CTCSS tone frequency in dHz.
1.3.6.1.4.1.3570.2.2.2.1.2.2.5.11ScalarrctRfTxSelectedEncodeSubAudibleTyperead-onlycurrentThe configured transmit sub-audible signaling type
1.3.6.1.4.1.3570.2.2.2.1.2.2.5.12ScalarrctRfTxSelectFrequencyResponseread-onlycurrentSpecifies the transmit baseband frequency response that applies to the channel. MPT Control channels have a flat speech charactieristic. MPT Traffic channels h…
1.3.6.1.4.1.3570.2.2.2.1.2.2.5.13ScalarrctRfTxSelectedEncodeDCSread-onlycurrentThe DCS sub-audible signalling value that the base station applies while transmitting.
1.3.6.1.4.1.3570.2.2.2.1.2.2.5.14ScalarrctRfTxSelectedEncodeSubAudibleDeviationread-onlycurrentThe deviation that CTCSS or DCS signaling will cause to the carrier frequency. It is in Hz.
1.3.6.1.4.1.3570.2.2.2.1.2.2.5.16ScalarrctRfTxRfRepeatStateread-onlycurrentThe current RF repeat state. disabled(0): RF is not repeated. The reciter acts as a base station. enabled(1): RF is repeated. The reciter acts as a repeater.
1.3.6.1.4.1.3570.2.2.2.1.2.2.6NoderctTemperature
1.3.6.1.4.1.3570.2.2.2.1.2.2.6.1ScalarrctTemperatureBoardread-onlycurrentThe reciter temperature in degrees Celsius, measured on the reciter circuit board. Range: -30..125
1.3.6.1.4.1.3570.2.2.2.1.2.2.7NoderctSystemInterface
1.3.6.1.4.1.3570.2.2.2.1.2.2.7.1ScalarrctSiConfiguredBalancedLineInLevelread-onlycurrentThe configured level of the balanced line input in dBm. Range: -30..0
1.3.6.1.4.1.3570.2.2.2.1.2.2.7.2ScalarrctSiConfiguredBalancedLineOutLevelread-onlycurrentThe configured level of the balanced line output in dBm. Range: -30..0
1.3.6.1.4.1.3570.2.2.2.1.2.2.7.3ScalarrctSiTxKeyread-onlycurrentThe state of the Tx key input. Range: Active(1), Inactive(2)
1.3.6.1.4.1.3570.2.2.2.1.2.2.7.4ScalarrctSiRxGateread-onlycurrentThe state of the Rx Gate output. Range: Active(1), Inactive(2)
1.3.6.1.4.1.3570.2.2.2.1.2.3NodepowerAmplifier
1.3.6.1.4.1.3570.2.2.2.1.2.3.1NodepaSummary
1.3.6.1.4.1.3570.2.2.2.1.2.3.1.1NodepaInfo
1.3.6.1.4.1.3570.2.2.2.1.2.3.1.1.1ScalarpaInfoProductCoderead-onlycurrentThe power amplifier product code. Product codes are explained in the Specifications Manual.
1.3.6.1.4.1.3570.2.2.2.1.2.3.1.1.2ScalarpaInfoSerialNumberread-onlycurrentPower amplifier serial number. A unique identifier assigned to the module in the factory.
1.3.6.1.4.1.3570.2.2.2.1.2.3.1.1.3ScalarpaInfoHardwareVersionread-onlycurrentThe power amplifier hardware version number.
1.3.6.1.4.1.3570.2.2.2.1.2.3.1.1.4ScalarpaInfoFirmwareVersionread-onlycurrentThe version number of the firmware currently installed on the power amplifier.
1.3.6.1.4.1.3570.2.2.2.1.2.3.1.2NodepaHealth
1.3.6.1.4.1.3570.2.2.2.1.2.3.2NodepaTxOutput
1.3.6.1.4.1.3570.2.2.2.1.2.3.2.1ScalarpaTxOutputForwardPowerread-onlycurrentThe measured forward power of the PA output in Watts. Range: 0..100
1.3.6.1.4.1.3570.2.2.2.1.2.3.2.2ScalarpaTxOutputVSWRread-onlycurrentThe transmitter's voltage standing wave ratio (VSWR).
1.3.6.1.4.1.3570.2.2.2.1.2.3.4NodepaTemperature
1.3.6.1.4.1.3570.2.2.2.1.2.3.5NodepaGeneral
1.3.6.1.4.1.3570.2.2.2.1.2.4NodepowerManagementUnit
1.3.6.1.4.1.3570.2.2.2.1.2.4.1NodepmuSummary
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.1NodepmuInfo
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.1.1ScalarpmuInfoProductCoderead-onlycurrentThe product code for the PMU.
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.1.2ScalarpmuInfoSerialNumberread-onlycurrentPMU serial number. A unique identifier assigned to the PMU in the factory.
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.1.3ScalarpmuInfoHardwareVersionread-onlycurrentThe PMU hardware version number.
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.1.4ScalarpmuInfoFirmwareVersionread-onlycurrentThe version number of the firmware currently installed on the PMU.
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.1.5ScalarpmuInfoCalibrationUpdateDateread-onlycurrentIndicates when the PMU was last calibrated.
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.2NodepmuHealth
1.3.6.1.4.1.3570.2.2.2.1.2.4.1.3NodepmuSubmodules
1.3.6.1.4.1.3570.2.2.2.1.2.4.2NodepmuState
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.1ScalarpmuStateMainsInStateread-onlycurrentThe condition of the PMU's AC power input. Range: bad(0): The AC power input is off, or too low, or too high. good(1): The AC power input is usable. not fitted…
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.2ScalarpmuStateBatteryInStateread-onlycurrentThe condition of the PMU's DC power input. Range: bad(0): The DC power input is off, or too low, or too high. good(1): The DC power input is usable. not fitted…
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.3ScalarpmuStateBatteryInVoltageread-onlycurrentThe measured voltage of the DC (battery) power supply to the PMU. Range: 10.5..15.5.
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.4ScalarpmuStateOutCurrentread-onlycurrentThe output current in mA that the PMU is supplying to the subrack (PA(s), reciter(s) and control panel). Range: 0..20000.
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.5ScalarpmuStateOutVoltageread-onlycurrentThe actual voltage of the PMU output(s) to the PA(s) and reciter(s) in the subrack (nominally 28 V). Range: 0..32.
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.6ScalarpmuStateOutStatusread-onlycurrentThe condition of the PMU power supply to the PA. Range: bad(0): The power supply is absent or its voltage is too low or too high. good(1): The power supply is …
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.7ScalarpmuStateAuxOutStateread-onlycurrentThe condition of the auxiliary power output. Range: bad(0): The auxiliary power is off, or its voltage is too high or too low. good(1): The auxiliary power out…
1.3.6.1.4.1.3570.2.2.2.1.2.4.2.9ScalarpmuStateBusConnectread-onlycurrentThe state of the DC supply to the PMU's standby converter. Range: connected(1), not connected(2)
1.3.6.1.4.1.3570.2.2.2.1.2.5NodefrontPanel
1.3.6.1.4.1.3570.2.2.2.1.2.5.1NodefpSummary
1.3.6.1.4.1.3570.2.2.2.1.2.5.1.1NodefpInfo
1.3.6.1.4.1.3570.2.2.2.1.2.5.1.1.1ScalarfpInfoProductCoderead-onlycurrentThe product code for the front panel.
1.3.6.1.4.1.3570.2.2.2.1.2.5.1.1.2ScalarfpInfoSerialNumberread-onlycurrentFront panel serial number. A unique identifier assigned to the front panel in the factory.
1.3.6.1.4.1.3570.2.2.2.1.2.5.1.1.3ScalarfpInfoHardwareVersionread-onlycurrentFront panel hardware version number.
1.3.6.1.4.1.3570.2.2.2.1.2.5.1.1.4ScalarfpInfoFirmwareVersionread-onlycurrentThe version number of the firmware currently installed on the front panel.
1.3.6.1.4.1.3570.2.2.2.1.2.5.1.2NodefpHealth
1.3.6.1.4.1.3570.2.2.2.1.3Nodealarms
1.3.6.1.4.1.3570.2.2.2.1.3.1NodealarmSummary
1.3.6.1.4.1.3570.2.2.2.1.3.1.1ScalaralarmSummaryBaseStationread-onlycurrentBase station summary alarm. The base station currently has one or more active alarms. Connect to the base station to see what these alarms are. Range: unavaila…
1.3.6.1.4.1.3570.2.2.2.1.3.1.2ScalaralarmSummaryReciterread-onlycurrentReciter summary alarm. The reciter currently has one or more active alarms. Connect to the base station to see what these alarms are. Range: unavailable(0), cl…
1.3.6.1.4.1.3570.2.2.2.1.3.1.3ScalaralarmSummaryPowerAmplifierread-onlycurrentPA summary alarm. The PA currently has one or more active alarms. Connect to the base station to see what these alarms are. Range: unavailable(0), cleared(1), …
1.3.6.1.4.1.3570.2.2.2.1.3.1.4ScalaralarmSummaryPowerManagementUnitread-onlycurrentPMU summary alarm. The PMU currently has one or more active alarms. Connect to the base station to see what these alarms are. Range: unavailable(0), cleared(1)…
1.3.6.1.4.1.3570.2.2.2.1.3.1.5ScalaralarmSummaryCustomAlarmsread-onlycurrentCustom summary alarm. There are currently one or more active custom alarms. Connect to the base station to see what these alarms are. Range: unavailable(0), cl…
1.3.6.1.4.1.3570.2.2.2.1.3.1.6ScalaralarmSummaryFrontPanelread-onlycurrentFront panel summary alarm. The front panel currently has one or more active alarms. Connect to the base station to see what these alarms are. Range: unavailabl…
1.3.6.1.4.1.3570.2.2.2.1.3.1.7ScalaralarmSummarySystemread-onlycurrentSystem summary alarm. One or more system conditions have triggered alarms. This does not indicate a base station fault. Connect to the base station to see what…
1.3.6.1.4.1.3570.2.2.2.1.3.1.8ScalaralarmSummaryMinorread-onlycurrentMinor summary alarm. The base station currently has one or more minor alarms. The node will select other channels in preference. Connect to the base station to…
1.3.6.1.4.1.3570.2.2.2.1.3.1.9ScalaralarmSummaryMajorread-onlycurrentMajor summary alarm. The base station currently has one or more major alarms. The node will take it out of service. Connect to the base station to see what the…
1.3.6.1.4.1.3570.2.2.2.1.3.3NodereciterAlarms
1.3.6.1.4.1.3570.2.2.2.1.3.3.2ScalarrctAlarmRxSynthOutOfLockread-onlycurrentReceiver synthesizer alarm. The receiver synthesizer is unable to lock on to the frequency it is configured to operate at. In response, the base station disabl…
1.3.6.1.4.1.3570.2.2.2.1.3.3.3ScalarrctAlarmInvalidChannelSelectedread-onlycurrentChannel invalid alarm. An invalid channel number was selected. The base station has stopped operating. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.3.10ScalarrctAlarmOverTemperatureread-onlycurrentTemperature high alarm. The reciter is approaching its maximum operating temperature. Check if the ambient temperature high alarm is active (Monitor > Alarms >…
1.3.6.1.4.1.3570.2.2.2.1.3.3.13ScalarrctAlarmTxCalibrationInvalidread-onlycurrentTransmitter calibration invalid alarm. This alarm activates if the exciter has become uncalibrated. Send the reciter for repair. Range: unavailable(0), cleared…
1.3.6.1.4.1.3570.2.2.2.1.3.3.14ScalarrctAlarmRxCalibrationInvalidread-onlycurrentReciter receiver calibration invalid alarm. The RSSI needs to be calibrated for the operational frequency of the channel. Connect to the base station and re-ca…
1.3.6.1.4.1.3570.2.2.2.1.3.3.15ScalarrctAlarmInvalidConfigurationread-onlycurrentReciter hardware configuration invalid alarm, the base station modules are not compatible Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.3.16ScalarrctAlarm25MHzSynthOutOfLockread-onlycurrentSynthesizer out of lock alarm. The reciter's 25 MHz synthesizer cannot remain locked to the external reference. Range: unavailable(0), cleared(1), raised(2), d…
1.3.6.1.4.1.3570.2.2.2.1.3.3.17ScalarrctAlarm6144MHzSynthOutOfLockread-onlycurrentSynthesizer out of lock alarm. The reciter's 61.44 MHz synthesizer cannot remain locked to the external reference. Range: unavailable(0), cleared(1), raised(2)…
1.3.6.1.4.1.3570.2.2.2.1.3.3.18ScalarrctAlarmTxFSynthOutOfLockread-onlycurrentThe TxF synthesizer is unable to lock on to the frequency it is configured to operate at. In response, the base station disabled the transmitter. Send the reci…
1.3.6.1.4.1.3570.2.2.2.1.3.3.19ScalarrctAlarmSimulcastSynchread-onlycurrentThe base station cannot achieve synchronization to common time reference required for simulcast operation. If simulcast not needed, uncheck simulcast box in ch…
1.3.6.1.4.1.3570.2.2.2.1.3.3.20ScalarrctAlarmReceiverSynchread-onlycurrentReports whether the receiver is aligned with the transmit TDMA frame synchronization of the transmitters of the channel group. Possible causes for the receiver…
1.3.6.1.4.1.3570.2.2.2.1.3.3.21ScalarrctAlarmTxRSynthOutOfLockread-onlycurrentThe TxR synthesizer is unable to lock on to the frequency it is configured to operate at. In response, the base station disabled the transmitter. Send the reci…
1.3.6.1.4.1.3570.2.2.2.1.3.4NodepaAlarms
1.3.6.1.4.1.3570.2.2.2.1.3.4.1ScalarpaAlarmNoPADetectedread-onlycurrentPA not detected alarm. The reciter has not received a response from a PA over the control bus. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.4.2ScalarpaAlarmInvalidFirmwareread-onlycurrentPA firmware invalid alarm. The firmware in the PA is invalid. 1. Connect to the base station and activate the latest PA firmware. 2. Replace the PA and send it…
1.3.6.1.4.1.3570.2.2.2.1.3.4.3ScalarpaAlarmInvalidCalibrationread-onlycurrentInvalid PA calibration alarm. This alarm can only be triggered on start-up, when the PA carries out self-tests. It indicates that settings stored in firmware h…
1.3.6.1.4.1.3570.2.2.2.1.3.4.5ScalarpaAlarmForwardPowerLowread-onlycurrentForward power low alarm. The PA forward power output is below the configured minimum limit. If the VSWR is also raised, check for a load mismatch. Otherwise, t…
1.3.6.1.4.1.3570.2.2.2.1.3.4.7ScalarpaAlarmPowerFoldbackread-onlycurrentPower foldback alarm. The PA has detected a fault condition and, to prevent damage, reduced its power output to 35 Watts. (But only if the configured power out…
1.3.6.1.4.1.3570.2.2.2.1.3.4.8ScalarpaAlarmReversePowerHighread-onlycurrentReverse power high alarm. The PA's reverse power is above the configured maximum. Check for a load mismatch. This alarm has a resolution of only 1W so it isn't…
1.3.6.1.4.1.3570.2.2.2.1.3.4.9ScalarpaAlarmShutdownImminentread-onlycurrentPA shut-down alarm. The PA is not operational. It detected a fault condition and disabled the transmitter to prevent damage. Range: unavailable(0), cleared(1),…
1.3.6.1.4.1.3570.2.2.2.1.3.4.10ScalarpaAlarmVSWRFaultread-onlycurrentVSWR alarm. The PA's Voltage Standing Wave Ratio (VSWR) is above the configured threshold. A normal VSWR is <= 2:1. A high VSWR automatically means reduced out…
1.3.6.1.4.1.3570.2.2.2.1.3.4.11ScalarpaAlarmDriverCurrentHighread-onlycurrentDriver current high alarm. The driver is drawing excessive current. A fixed limit has been exceeded. Replace the PA and send it for repair. Range: unavailable(…
1.3.6.1.4.1.3570.2.2.2.1.3.4.12ScalarpaAlarmFinal1CurrentHighread-onlycurrentFinal 1 current high alarm. The current in the PA's final 1 output stage has exceeded a fixed limit. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.4.13ScalarpaAlarmFinal2CurrentHighread-onlycurrentFinal 2 current high alarm. The current in the PA's final 2 output stage has exceeded a fixed limit. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.4.14ScalarpaAlarmCurrentImbalanceread-onlycurrentCurrent imbalance alarm. One of the PA's final stages is drawing significantly more current than the other. Range: unavailable(0), cleared(1), raised(2), disab…
1.3.6.1.4.1.3570.2.2.2.1.3.4.15ScalarpaAlarmSupplyVoltageLowread-onlycurrentSupply voltage low alarm. The PA supply voltage is 26 V or less, probably because the battery supply to the PMU is running low. Range: unavailable(0), cleared(…
1.3.6.1.4.1.3570.2.2.2.1.3.4.16ScalarpaAlarmSupplyVoltageHighread-onlycurrentSupply voltage high alarm. The power supplied to the PA is 29 V or more. The PMU is faulty and needs replacing, Range: unavailable(0), cleared(1), raised(2), d…
1.3.6.1.4.1.3570.2.2.2.1.3.4.17ScalarpaAlarmDriverTemperatureHighread-onlycurrentDriver temperature high alarm. The temperature in the PA's driver output stage has exceeded the configured threshold. If it continues to rise and exceeds a bui…
1.3.6.1.4.1.3570.2.2.2.1.3.4.18ScalarpaAlarmFinal1TemperatureHighread-onlycurrentFinal 1 temperature high alarm. The temperature in the PA's final 1 output stage has exceeded the configured threshold. If it continues to rise and exceeds a b…
1.3.6.1.4.1.3570.2.2.2.1.3.4.19ScalarpaAlarmFinal2TemperatureHighread-onlycurrentFinal 2 temperature high alarm. The temperature in the PA's final 2 output stage has exceeded the configured threshold. If it continues to rise and exceeds a b…
1.3.6.1.4.1.3570.2.2.2.1.3.5NodepmuAlarms
1.3.6.1.4.1.3570.2.2.2.1.3.5.1ScalarpmuAlarmNoPMUDetectedread-onlycurrentPMU not detected alarm. The reciter has not received a response from the PMU over the control bus. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.5.2ScalarpmuAlarmInvalidFirmwareread-onlycurrentPMU firmware invalid alarm. The firmware in the PMU is invalid. 1. Connect to the base station and activate the PMU firmware. 2. Replace the PMU and send it fo…
1.3.6.1.4.1.3570.2.2.2.1.3.5.4ScalarpmuAlarmMainsFailureread-onlycurrentMains supply alarm. The mains power supply to the PMU is absent or its voltage is outside acceptable limits. The PMU is using DC power instead. Range: unavaila…
1.3.6.1.4.1.3570.2.2.2.1.3.5.5ScalarpmuAlarmSelfTestFailureread-onlycurrentPMU power-up fault. During start-up, the PMU detected an internal error and will reset itself. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.5.6ScalarpmuAlarmShutdownImminentread-onlycurrentShut-down imminent alarm. A battery is currently powering the base station and its voltage has fallen below the configured power shut-down voltage. The PMU wil…
1.3.6.1.4.1.3570.2.2.2.1.3.5.7ScalarpmuAlarmTemperatureHighread-onlycurrentPMU temperature alarm. One of the PMU temperature sensors has detected a temperature that is above the fixed limit. Range: unavailable(0), cleared(1), raised(2…
1.3.6.1.4.1.3570.2.2.2.1.3.5.8ScalarpmuAlarmBatteryProtectread-onlycurrentBattery protection mode alarm. Battery protection mode is on. If mains power fails, the PMU will shut down to protect the battery. Battery protection mode is e…
1.3.6.1.4.1.3570.2.2.2.1.3.5.9ScalarpmuAlarmBatteryVoltageLowread-onlycurrentLow battery voltage alarm. The DC voltage supply to the PMU is below the configured alarm threshold. If mains power is lost, the PMU is likely to reduce its ou…
1.3.6.1.4.1.3570.2.2.2.1.3.5.10ScalarpmuAlarmBatteryVoltageHighread-onlycurrentBattery voltage high alarm. The voltage of the DC power supply to the PMU is higher than the configured maximum. The base station takes no action until the vol…
1.3.6.1.4.1.3570.2.2.2.1.3.5.11ScalarpmuAlarmCurrentOutHighread-onlycurrentPMU high current alarm. The PMU is providing > 15 A of current and is automatically lowering its output voltage. There is a short circuit or the PMU is faulty.…
1.3.6.1.4.1.3570.2.2.2.1.3.5.12ScalarpmuAlarmVoltageOutLowread-onlycurrentOutput voltage low alarm. The PMU's DC output (nominally 28 V) is lower than the fixed minimum of 24 V. Range: unavailable(0), cleared(1), raised(2), disabled(…
1.3.6.1.4.1.3570.2.2.2.1.3.5.13ScalarpmuAlarmVoltageOutHighread-onlycurrentHigh voltage alarm. The PMU's DC output (nominally 28 V) is higher than the fixed maximum of 32 V. Range: unavailable(0), cleared(1), raised(2), disabled(3)
1.3.6.1.4.1.3570.2.2.2.1.3.6NodecustomAlarms
1.3.6.1.4.1.3570.2.2.2.1.3.6.1ScalarcustomAlarm1read-onlycurrentCustom alarm 1. The state of digital input 1 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.2ScalarcustomAlarm2read-onlycurrentCustom alarm 2. The state of digital input 2 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.3ScalarcustomAlarm3read-onlycurrentCustom alarm 3. The state of digital input 3 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.4ScalarcustomAlarm4read-onlycurrentCustom alarm 4. The state of digital input 4 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.5ScalarcustomAlarm5read-onlycurrentCustom alarm 5. The state of digital input 5 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.6ScalarcustomAlarm6read-onlycurrentCustom alarm 6. The state of digital input 6 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.7ScalarcustomAlarm7read-onlycurrentCustom alarm 7. The state of digital input 7 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.8ScalarcustomAlarm8read-onlycurrentCustom alarm 8. The state of digital input 8 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.9ScalarcustomAlarm9read-onlycurrentCustom alarm 9. The state of digital input 9 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When conf…
1.3.6.1.4.1.3570.2.2.2.1.3.6.10ScalarcustomAlarm10read-onlycurrentCustom alarm 10. The state of digital input 10 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When co…
1.3.6.1.4.1.3570.2.2.2.1.3.6.11ScalarcustomAlarm11read-onlycurrentCustom alarm 11. The state of digital input 11 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When co…
1.3.6.1.4.1.3570.2.2.2.1.3.6.12ScalarcustomAlarm12read-onlycurrentCustom alarm 12. The state of digital input 12 has changed, triggering this alarm. This occurs when external equipment has been connected to the input. When co…
1.3.6.1.4.1.3570.2.2.2.1.3.7NodefpAlarms
1.3.6.1.4.1.3570.2.2.2.1.3.7.1ScalarfpAlarmFan1read-onlycurrentFan alarm. The reciter has failed to detect Fan 1 when attempting to activate it upon start-up or when a module temperature threshold is exceeded. The fan may …
1.3.6.1.4.1.3570.2.2.2.1.3.7.2ScalarfpAlarmFan2read-onlycurrentFan alarm. The reciter has failed to detect Fan 2 when attempting to activate it upon start-up or when a module temperature threshold is exceeded. The fan may …
1.3.6.1.4.1.3570.2.2.2.1.3.7.3ScalarfpAlarmFan3read-onlycurrentFan alarm. The reciter has failed to detect Fan 3 when attempting to activate it upon start-up or when a module temperature threshold is exceeded. The fan may …
1.3.6.1.4.1.3570.2.2.2.1.3.7.4ScalarfpAlarmNoFPDetectedread-onlycurrentThe base station is unable to detect the front panel on the control bus. Check the connections of the D-range connector and system control bus cable. Range: un…
1.3.6.1.4.1.3570.2.2.2.1.3.7.5ScalarfpAlarmInvalidFirmwareread-onlycurrentInvalid front panel firmware alarm. Connect to the base station and select Tools > Firmware Download to acquire valid firmware. If the firmware is valid contac…
1.3.6.1.4.1.3570.2.2.2.1.3.8NodesystemAlarms
1.3.6.1.4.1.3570.2.2.2.1.3.8.1ScalarsystemAlarmAmbientTempLowread-onlycurrentAmbient temperature low alarm. The ambient temperature at the front panel air intake is below the configured minimum. Fan operation and PA power output are una…
1.3.6.1.4.1.3570.2.2.2.1.3.8.2ScalarsystemAlarmAmbientTempHighread-onlycurrentAmbient temperature high alarm. The ambient temperature at the front panel air intake has exceeded the configured maximum. Fan operation and PA power output ar…
1.3.6.1.4.1.3570.2.2.2.1.3.8.3ScalarsystemAlarmExternalRefAbsentread-onlycurrentExternal frequency reference absent alarm. The base station did not detect an external reference frequency source. It is now using its own source. An external …
1.3.6.1.4.1.3570.2.2.2.1.3.8.4ScalarsystemAlarmQoSJitterread-onlycurrentQoS jitter alarm. The incoming voice stream has a jitter equal to or greater than the configured threshold. Range: unavailable(0), cleared(1), raised(2), disab…
1.3.6.1.4.1.3570.2.2.2.1.3.8.5ScalarsystemAlarmQoSLostPacketsread-onlycurrentQoS lost packets alarm. The number of lost packets in the incoming voice stream has equalled or exceeded the configured threshold. Range: unavailable(0), clear…
1.3.6.1.4.1.3570.2.2.2.1.3.8.6ScalarsystemAlarmFallbackControlledread-onlycurrentThis base station is controlled by an Embedded Node in fallback mode.
1.3.6.1.4.1.3570.2.2.2.1.3.8.7ScalarsystemAlarmDuplicateNodePriorityread-onlycurrentThe base station's BSP priority is being used by another base station on the same site. This alarm is raised only if the base station has been configured as 'C…
1.3.6.1.4.1.3570.2.2.2.1.3.8.8ScalarsystemAlarmNTPSynchronisationread-onlycurrentThe base station hasn't had received an NTP signal from a server and the clock might be out of synchronization. Range: unavailable(0), cleared(1), raised(2), d…
1.3.6.1.4.1.3570.2.2.2.1.3.8.9ScalarsystemAlarm1PPSAbsentread-onlycurrentIn a simulcast system base stations must have a 1PPS pulse. This alarm should be disabled for other systems. It is not applicable to receive only base stations…
1.3.6.1.4.1.3570.2.2.2.1.3.8.10ScalarsystemAlarmQoSTransmitBufferread-onlycurrentSimulcast satellite base station is receiving packets that cannot fit into the transmit buffer. The alarm can be raised due to one of the two reasons: packets …
1.3.6.1.4.1.3570.2.2.2.1.3.8.11ScalarsystemAlarmCartesianLoopUnstableread-onlycurrentPA feedback loop to linearise transmitter can't achieve specified tolerances. Check TxR cable connected properly, otherwise return for repair. Range: unavailab…
1.3.6.1.4.1.3570.2.2.2.1.3.8.12ScalarsystemAlarmTxRCableAbsentread-onlycurrentPA feedback cable to reciter TxR is not working correctly/not present. Ensure that the TxR cable between PA and Reciter TxR is unbroken and connected securely,…
1.3.6.1.4.1.3570.2.2.2.1.4NodenetworkLinks
1.3.6.1.4.1.3570.2.2.2.1.4.1NodenetworkLinksSummary
1.3.6.1.4.1.3570.2.2.2.1.4.1.1NodelinkInfo
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.1ScalarlinkInfoCtrlProtocolStatusread-onlycurrentThe status of the base station as reported to the node using the control protocol. Range: unconnected(0): The base station is not under node control. deprecate…
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.2ScalarlinkInfoNetworkPacketCountread-onlycurrentTotal packets received from the network on control and data protocols. This is an accumulating number. The counter is large enough that the number rolls over i…
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.3ScalarlinkInfoMPTCtrlProtocolStatusread-onlycurrentThe status of the base station as reported to the node using the control protocol. unconnected(0): The base-station is not connected to any MPT-IP node, neithe…
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.4ScalarlinkInfoDMRNodeIPAddressread-onlycurrentThe IP address of the DMR Node Controlling the base station.
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.5ScalarlinkInfoDMRNodePriorityread-onlycurrentThe priority of the DMR Node Controlling the base station.
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.6ScalarlinkInfoMPTNodeIPAddressread-onlycurrentThe IP address of the MPT Node Controlling the base station.
1.3.6.1.4.1.3570.2.2.2.1.4.1.1.7ScalarlinkInfoMPTNodePriorityread-onlycurrentThe priority of the MPT Node Controlling the base station.
1.3.6.1.4.1.3570.2.2.2.1.4.1.2NodelinkHealth
1.3.6.1.4.1.3570.2.2.2.1.4.1.2.2ScalarlinkHealthNetworkPacketLostCountread-onlycurrentTotal accumulated number of lost voice and control packets sent from the control and switching nodes. An increasing number indicates that the linking infrastru…
1.3.6.1.4.1.3570.2.2.2.1.4.1.2.3ScalarlinkHealthNetworkJitterLastOverread-onlycurrentThe maximum jitter measured in the last over.
1.3.6.1.4.1.3570.2.2.2.1.4.1.2.4ScalarlinkHealthNetworkJitterCountread-onlycurrentThe total number of times the configured jitter threshold has been exceeded.
1.3.6.1.4.1.3570.2.2.2.1.4.1.2.5ScalarlinkHealthSequenceErrorsCountread-onlycurrentThe result of lost packets - i.e. the number of times packets have been received out of sequence. This is an accumulating number.
1.3.6.1.4.1.3570.2.2.2.1.5NodenetworkInterfaces
1.3.6.1.4.1.3570.2.2.2.1.5.1NodenwNtpInterface
1.3.6.1.4.1.3570.2.2.2.1.5.1.1ScalarnwConfiguredNtpServerAddressread-onlycurrentThe IP address configured for the preferred NTP server used by the base-station. The current status of NTP for the base-station including the selected server i…
1.3.6.1.4.1.3570.2.2.2.1.5.1.2ScalarnwConfiguredNtpBackupServerAddress1read-onlycurrentThe IP address configured for a backup NTP server used by the base-station. The current status of NTP for the base-station including the backup servers is avai…
1.3.6.1.4.1.3570.2.2.2.1.5.1.3ScalarnwConfiguredNtpBackupServerAddress2read-onlycurrentThe IP address configured for a backup NTP server used by the base-station. The current status of NTP for the base-station including the backup servers is avai…
1.3.6.1.4.1.3570.2.2.2.1.5.2NodenwChannelGroup
1.3.6.1.4.1.3570.2.2.2.1.5.2.1ScalarnwChannelGroupStatusread-onlycurrentThe voting role that the base station is currently playing within the channel group.
1.3.6.1.4.1.3570.2.2.2.1.5.2.2ScalarnwChannelGroupLocalBufferLevelread-onlycurrentThe lowest level of the transmit buffer, measured in milliseconds over a 5-second period.
1.3.6.1.4.1.3570.2.2.2.1.5.2.3ScalarnwChannelGroupEmptiestBufferLevelread-onlycurrentThe level of the transmit buffer (in ms) at the member that has got emptiest buffer-level. It is the smallest transmit buffer of any channel group member. If m…
1.3.6.1.4.1.3570.2.2.2.1.5.2.4ScalarnwChannelGroupMarshallingTyperead-onlycurrent[Simulcast] The Marshalling Type configuration setting indicates how the marshalling time is determined. Range: fixed(0): Configuration defines the marshalling…
1.3.6.1.4.1.3570.2.2.2.1.5.2.5ScalarnwChannelGroupMarshallingDurationread-onlycurrentIn simulcast, the current marshalling duration (in ms). This is fixed in configuration or automatically regulated. This parameter is only used by the central v…
1.3.6.1.4.1.3570.2.2.2.1.5.2.6ScalarnwChannelGroupReceiverSynchStatusread-onlycurrentThe receiver synchronization status indicates whether the base station's receiver is synchronized and if not then gives reasons why. Range: no-license(0): The …
1.3.6.1.4.1.3570.2.2.2.1.5.2.7ScalarnwChannelGroupTransmitterSynchStatusread-onlycurrentThe Synchronization status indicates whether the base station's transmission is synchronized and if not then gives reasons why. A base station transmitter in a…
1.3.6.1.4.1.3570.2.2.2.1.5.2.8ScalarnwChannelGroupLateStreamsCountread-onlycurrentThe number of times any transmission stream arrives later than the required transmit time. The count is aggregated one since system-startup.
1.3.6.1.4.1.3570.2.2.2.1.5.2.9ScalarnwChannelGroupOverflowCountread-onlycurrentThe number of channelgroup messages that did not fit in the transmit buffer or were too far into the future. The count is total such messages since system-star…
1.3.6.1.4.1.3570.2.2.2.1.5.2.10ScalarnwChannelGroupUnderflowCountread-onlycurrentThe number of times transmit-buffer ran empty, since system-startup.
1.3.6.1.4.1.3570.2.2.2.1.5.2.11ScalarnwChannelGroupLostPacketsCountread-onlycurrentThe number of packets that were lost during a transmission stream, based on the packet sequence numbering. The count is aggregated one since system-startup.
1.3.6.1.4.1.3570.2.2.2.1.5.2.12ScalarnwChannelGroupJitterread-onlycurrentThe jitter-value calculated in compliance with RFC-1889. It is the mean deviation (absolute value) of the difference in packet spacing at the receiver compared…
1.3.6.1.4.1.3570.2.2.2.1.5.3NodenwPorts
1.3.6.1.4.1.3570.2.2.2.1.5.3.1ScalarnwSvpPortread-onlycurrentThe configured Simulcast Voted protocol UDP port.
1.3.6.1.4.1.3570.2.2.2.5NodemibConformance
1.3.6.1.4.1.3570.2.2.2.5.1NodemibGroups
1.3.6.1.4.1.3570.2.2.2.5.1.1GrouphealthGroupcurrentThe health Group.
1.3.6.1.4.1.3570.2.2.2.5.1.2GroupalarmSummaryGroupcurrentThe alarmSummary Group.
1.3.6.1.4.1.3570.2.2.2.5.1.3GrouprctSelectedChannelGroupcurrentThe rctSelectedChannel Group.
1.3.6.1.4.1.3570.2.2.2.5.1.5GrouppaTxOutputGroupcurrentThe paTxOutput Group.
1.3.6.1.4.1.3570.2.2.2.5.1.6GrouplinkInfoGroupcurrentThe linkInfo Group.
1.3.6.1.4.1.3570.2.2.2.5.1.7GroupcustomAlarmsGroupcurrentThe customAlarms group.
1.3.6.1.4.1.3570.2.2.2.5.1.8GroupsystemAlarmsGroupcurrentThe systemAlarms Group.
1.3.6.1.4.1.3570.2.2.2.5.1.9GroupfpAlarmsGroupcurrentThe fpAlarms Group.
1.3.6.1.4.1.3570.2.2.2.5.1.10GrouppaAlarmsGroupcurrentThe paAlarms Group.
1.3.6.1.4.1.3570.2.2.2.5.1.11GrouppmuAlarmsGroupcurrentThe pmuAlarms Group.
1.3.6.1.4.1.3570.2.2.2.5.1.12GroupreciterAlarmsGroupcurrentThe reciterAlarms Group.
1.3.6.1.4.1.3570.2.2.2.5.1.13GroupinfoGroupcurrentThe info Group.
1.3.6.1.4.1.3570.2.2.2.5.1.14GrouprctReceiveQualityGroupcurrentThe receive quality Group.
1.3.6.1.4.1.3570.2.2.2.5.1.15GrouprctReceiverGroupcurrentThe receiver Group.
1.3.6.1.4.1.3570.2.2.2.5.1.16GrouprctTemperatureGroupcurrentThe reciter temperature group.
1.3.6.1.4.1.3570.2.2.2.5.1.17GrouppmuStateGroupcurrentThe pmu status indications group.
1.3.6.1.4.1.3570.2.2.2.5.1.18GroupnwNtpInterfaceGroupcurrentThe network ntp interface group.
1.3.6.1.4.1.3570.2.2.2.5.1.19GrouprctTransmitterGroupcurrentThe transmitter group.
1.3.6.1.4.1.3570.2.2.2.5.1.20GroupnwChannelGroupGroupcurrentThe group for channelgroup.
1.3.6.1.4.1.3570.2.2.2.5.1.21GroupnwPortsGroupcurrentNetwork ports
1.3.6.1.4.1.3570.2.2.2.5.1.22GrouprctSystemInterfaceGroupcurrentReciter system interface
1.3.6.1.4.1.3570.2.2.2.5.1.23GrouplinearTransmissionCapabilitycurrentInformation depending on existence of a linear power amplifier
1.3.6.1.4.1.3570.2.2.2.5.1.24GrouppmuInfoGroupcurrentThe PMU info group.
1.3.6.1.4.1.3570.2.2.2.5.1.27GroupdeprecatedOidGroupdeprecatedDeprecated OIDs
1.3.6.1.4.1.3570.2.2.2.5.2NodemibCompliance
1.3.6.1.4.1.3570.2.2.2.5.2.1CompliancemibComplianceListcurrentThe requirements for conformance to the TAIT-INFRA93SERIES-MIB.