TMU-MIB
216 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter Gauge internet IpAddress mgmt NetworkAddress TimeTicks |
| SNMPv2-TC | DisplayString MacAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2 | Nodemgmt | |||
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.22 | Nodefibronics | |||
| 1.3.6.1.4.1.22.60 | Nodetmu | |||
| 1.3.6.1.4.1.22.60.1 | NodetmuSystem | |||
| 1.3.6.1.4.1.22.60.1.1 | ScalarfibTmuNumEventErrs | read-only | mandatory | Cyclic counter. Indicates how many times the event-handler procedure has been called with the 'ERR' severity level or higher. |
| 1.3.6.1.4.1.22.60.1.2 | ScalarfibTmuArpAgeTime | read-only | mandatory | The value of the system timer [in SYS-TICKs] at the last time ARP aging was carried out. |
| 1.3.6.1.4.1.22.60.1.3 | ScalarfibTmuNumRarpUpdate | read-only | mandatory | Cyclic counter. Indicates how many times the system's IP address was updated because of a RARP message. |
| 1.3.6.1.4.1.22.60.1.4 | ScalarfibTmuMainSwVersion | read-only | mandatory | United version for all software packages in this system. |
| 1.3.6.1.4.1.22.60.1.5 | ScalarfibTmuEepromVersion | read-only | mandatory | Version of the eeprom package |
| 1.3.6.1.4.1.22.60.1.6 | ScalarfibTmuEepromDeffective | read-only | mandatory | System information. Set when eeprom is found to be physically deffective and can not be read nor written to. |
| 1.3.6.1.4.1.22.60.1.7 | ScalarfibTmuLastSysIfIndex | read-only | mandatory | Number of inteface via which the last ip message was received. Currently interfaces 1->3 are token ring interfaces and interface 4 is the serial/slip interface. |
| 1.3.6.1.4.1.22.60.1.8 | ScalarfibTmuTrDrvVersion | read-only | mandatory | The software version of the token ring driver as received from the driver at initialization. |
| 1.3.6.1.4.1.22.60.1.9 | ScalarfibTmuSccDrvVersion | read-only | mandatory | The software version of the serial line driver as received from the driver at initialization. |
| 1.3.6.1.4.1.22.60.1.10 | ScalarfibTmuSnmpUsrVersion | read-only | mandatory | The software version of the sw package employing udp/ip/snmp and the preliminary reduction of messages from any of the interfaces. Loaded at initialization. |
| 1.3.6.1.4.1.22.60.1.11 | ScalarfibTmuDisplayDebugMode | read-write | mandatory | Flag indicating whether system is in a special debug mode. In that mode, extra code is executed to output indications on system state. |
| 1.3.6.1.4.1.22.60.1.12 | ScalarfibTmuEeFaultsFormat | read-write | mandatory | Flag indicating whether faults stored in eeprom will each take a small eeprom space or a large eeprom space. If the 'small' option is chosen, only so many firs… |
| 1.3.6.1.4.1.22.60.1.13 | ScalarfibTmuRunFaultsFormat | read-only | mandatory | This is the run time value of flag described in eeFaultsFormat above. |
| 1.3.6.1.4.1.22.60.1.14 | ScalarfibTmuFunctionalityVersion | read-only | mandatory | The software version of the sw package which realizes the recovery process when the token ring fails (e.g. beaconing). Loaded at initialization. |
| 1.3.6.1.4.1.22.60.1.15 | ScalarfibTmuUtilitiesVersion | read-only | mandatory | The software version of the sw package containing operating system and hw utilities. Loaded at initialization. |
| 1.3.6.1.4.1.22.60.1.16 | ScalarfibTmuWrapIn | read-write | mandatory | Get: Read the state of the specified relay (wrap on 'ring in' port on trunk). Wrap may be set either by the manager or by the Tmu due to some errors on the tru… |
| 1.3.6.1.4.1.22.60.1.17 | ScalarfibTmuWrapOut | read-write | mandatory | Get: Read the state of the specified relay (wrap on 'ring Out' port on trunk). Wrap may be set either by the manager or by the Tmu due to some errors on the tr… |
| 1.3.6.1.4.1.22.60.1.18 | ScalarfibTmuLoadEeDefaults | read-write | mandatory | When this object is set, the Tmu system is instructed to load non volatile memory by default values at the next reset. Get: Read the value the system will use … |
| 1.3.6.1.4.1.22.60.1.19 | ScalarfibTmuDontResetFatal | read-write | mandatory | When this object is set, the Tmu system is instructed to reset the system when a fatal error has been detected. For debug purposes. In regular cases, this vari… |
| 1.3.6.1.4.1.22.60.1.20 | ScalarfibTmuRIConnection | read-only | mandatory | GET: Read what kind of trank is connected to Ring In port. At board type 9232/nn has no value. |
| 1.3.6.1.4.1.22.60.1.21 | ScalarfibTmuROConnection | read-only | mandatory | GET: Read what kind of trank is connected to Ring Out port. At board type 9232/nn has no value. |
| 1.3.6.1.4.1.22.60.1.22 | ScalarfibTmuRealTimeClock | read-write | mandatory | Get: Read real time with format hh:mm:ss DDD dd/MMM/yy. Set: Recive Display string of format hh:mm:ss DDD dd/MMM/yy. |
| 1.3.6.1.4.1.22.60.2 | NodetmuIntrfc | |||
| 1.3.6.1.4.1.22.60.2.1 | TablefibTmuIntrfcTable | not-accessible | mandatory | Table containing information and control items concerning a specific IP handling interface. |
| 1.3.6.1.4.1.22.60.2.1.1 | RowfibTmuIntrfcEntry | not-accessible | mandatory | Entry of information and control items concerning a specific IP handling interface. |
| 1.3.6.1.4.1.22.60.2.1.1.1 | ColumnfibTmuIntrfcIndex | read-only | mandatory | The value of this object identifies the IP interface for which this entry contains management information. The value of this object for a particular interface … |
| 1.3.6.1.4.1.22.60.2.1.1.2 | ColumnfibTmuNumRarpRcvd | read-only | mandatory | Cyclic counter. Contains the number of rarp response messages received via this interface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.3 | ColumnfibTmuNumRxRjctMem | read-only | mandatory | Cyclic counter. Contains the number of non-mac messages which were received by the tr chip but rejected by the higher sw levels because there was no memory. |
| 1.3.6.1.4.1.22.60.2.1.1.4 | ColumnfibTmuNumRxAccepted | read-only | mandatory | Cyclic counter. Contains the number of non-mac frames received by higher level sw. |
| 1.3.6.1.4.1.22.60.2.1.1.5 | ColumnfibTmuNumRxBdcst | read-only | mandatory | Cyclic counter. Contains the number of non-mac broadcast frames received by higher level SW. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.6 | ColumnfibTmuNumRxSpecific | read-only | mandatory | Cyclic counter. Contains the number of non-mac specific [non-broadcast, non-functional, non-group] frames received by higher level SW. Meaningful for Token Rin… |
| 1.3.6.1.4.1.22.60.2.1.1.7 | ColumnfibTmuNumRifIncluded | read-only | mandatory | Cyclic counter. Contains the number of non-mac frames with routing info field received by higher level SW. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.8 | ColumnfibTmuNumNoRif | read-only | mandatory | Cyclic counter. Contains the number of non-mac frames without routing info field received by higher level SW. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.9 | ColumnfibTmuNumNonSnap | read-only | mandatory | Cyclic counter. Contains the number of non-mac frames which were not snap messages and which were handed over to higher level SW by the mac level SW. These mes… |
| 1.3.6.1.4.1.22.60.2.1.1.10 | ColumnfibTmuNumUnknownType | read-only | mandatory | Cyclic counter. Contains the number of non-mac frames which had an unknown 'TYPE' field in the snap header and which were handed over to higher level SW by the… |
| 1.3.6.1.4.1.22.60.2.1.1.11 | ColumnfibTmuNumRifLong | read-only | mandatory | Cyclic counter. Contains the number of non-mac frames which had a routing information field [rif] which was longer than the UDPIP package can take [for learnin… |
| 1.3.6.1.4.1.22.60.2.1.1.12 | ColumnfibTmuNumRrpRjctIp | read-only | mandatory | Cyclic counter. Contains the number of rarp messages which were rejected because the message contents was illegal [e.g. illegal ip address]. Meaningful for Tok… |
| 1.3.6.1.4.1.22.60.2.1.1.13 | ColumnfibTmuNumArpRcvd | read-only | mandatory | Cyclic counter. Contains the number of arp response messages received via this interface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.14 | ColumnfibTmuNumIpRcvd | read-only | mandatory | Cyclic counter. Contains the number of ip response messages received via this interface. |
| 1.3.6.1.4.1.22.60.2.1.1.15 | ColumnfibTmuNumIfDown | read-only | mandatory | Cyclic counter. Number of times a message was directed to an interface which was 'down'. |
| 1.3.6.1.4.1.22.60.2.1.1.16 | ColumnfibTmuNumOwnBrdcst | read-only | mandatory | Cyclic counter. Contains the number of broadcast frames which were received in one of the system's macs and which were very same messages sent by one of the sy… |
| 1.3.6.1.4.1.22.60.2.1.1.17 | ColumnfibTmuAc00Cntr | read-only | mandatory | Cyclic counter. Contains the number of frames which were received with the 'A' and 'C' bits both '0'. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.18 | ColumnfibTmuAc01Cntr | read-only | mandatory | Cyclic counter. contains the number of frames which were received with the 'A' and 'C' bits equal to '0' and '1'. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.19 | ColumnfibTmuAc10Cntr | read-only | mandatory | Cyclic counter. Contains the number of frames which were received with the 'A' and 'C' bits equal to '1' and '0'. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.20 | ColumnfibTmuAc11Cntr | read-only | mandatory | Cyclic counter. Contains the number of frames which were received with the 'A' and 'C' bits equal to '1' and '1'. |
| 1.3.6.1.4.1.22.60.2.1.1.21 | ColumnfibTmuParityEc | read-only | mandatory | Cyclic counter. Contains the number of times scc reported parity error [per character]. Meaningful for serial intefaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.22 | ColumnfibTmuFrameEc | read-only | mandatory | Cyclic counter. Contains the number of times scc reported framing error [per character]. Meaningful for serial intefaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.23 | ColumnfibTmuRxNoiseEc | read-only | mandatory | Cyclic counter. Contains the number of times scc reported noise error [per character]. Meaningful for serial intefaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.24 | ColumnfibTmuBreakEc | read-only | mandatory | Cyclic counter. Contains the number of times scc reported break character was received. Meaningful for serial intefaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.25 | ColumnfibTmuNumConfigNotValid | read-only | mandatory | Cyclic counter. Contains the number of times get-naun or get-config of tr driver reported 'MAC-ERR-CONFIG-NOT-VALID'. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.26 | ColumnfibTmuNumAddrNotFound | read-only | mandatory | Cyclic counter. Contains the number of times get-naun or get-config of tr driver reported 'MAC-ERR-ADDR-NOT-FOUND'. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.27 | ColumnfibTmuNumProcessDisabled | read-only | mandatory | Cyclic counter. Contains the number of times get-naun or get-config of tr driver reported 'MAC-ERR-PROCESS-DISABLED'. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.28 | ColumnfibTmuNumBeaconsRcvd | read-only | mandatory | Cyclic counter. Contains the number of times tr driver reported receiving a beacon on this interface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.29 | ColumnfibTmuLastBeaconTime | read-only | mandatory | Time [in sys timer units] when last beacon was reported on this intrerface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.30 | ColumnfibTmuLastBeaconType | read-only | mandatory | Type of the last beacon reported on this intrerface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.31 | ColumnfibTmuLastBeaconAddr | read-only | mandatory | Mac address of the last station which reported 'beacon' on this interface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.32 | ColumnfibTmuLastBeaconNaun | read-only | mandatory | Mac address of the next upsream neighbour of the last station which reported 'beacon' on this interface. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.33 | ColumnfibTmuNumRxGroup | read-only | mandatory | Cyclic counter. Contains the number of non-mac group frames received by higher level SW. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.2.1.1.34 | ColumnfibTmuNumRxFunctional | read-only | mandatory | Cyclic counter. Contains the number of non-mac functional frames received by higher level SW. Meaningful for Token Ring interfaces only. |
| 1.3.6.1.4.1.22.60.3 | NodetmuMatch | |||
| 1.3.6.1.4.1.22.60.3.1 | ScalarfibTmuMatchUpdateTime | read-only | mandatory | Time [in sys timer units] from startup at which the table below has been updated. See remark in fibTmuMatchListValid below. |
| 1.3.6.1.4.1.22.60.3.2 | ScalarfibTmuMatchNumEntries | read-only | mandatory | Number of meaningful entries in the match array. The index of the last meaningful entry is num-entries. See remark in fibTmuMatchListValid below. |
| 1.3.6.1.4.1.22.60.3.3 | ScalarfibTmuMatchNumTmuEntries | read-only | mandatory | Number of meaningful entries in the match array which belong to stations attached to the tmu via tau ports. This does not include the two (or one) chipsets the… |
| 1.3.6.1.4.1.22.60.3.4 | ScalarfibTmuMatchFirstChipIndex | read-only | mandatory | The index in the match table at which the the first chipset is located (order of stations on match table is downstream, i.e. in the direction messages are tran… |
| 1.3.6.1.4.1.22.60.3.5 | ScalarfibTmuMatchSecondChipIndex | read-only | mandatory | The index in the match table at which the the second chipset is located (order of stations on match table is downstream, i.e. in the direction messages are tra… |
| 1.3.6.1.4.1.22.60.3.6 | ScalarfibTmuMatchActMonIndex | read-only | mandatory | The index in the match table at which the active monitor is located (order of stations on match table is downstream, i.e. in the direction messages are transpo… |
| 1.3.6.1.4.1.22.60.3.7 | ScalarfibTmuMatchConfigChipIndex | read-only | mandatory | The index in the match table from which the information for the configuration was collected (order of stations on match table is downstream, i.e. in the direct… |
| 1.3.6.1.4.1.22.60.3.8 | ScalarfibTmuMatchListValid | read-only | mandatory | Flag indicating whether the information in the tmuMatch group is valid or not. If information is not valid, ALL objects will return with a 'no such object' res… |
| 1.3.6.1.4.1.22.60.3.9 | ScalarfibTmuMatchUpToDate | read-only | mandatory | Flag. If set '1' then the information in All objects of tmuMatch group is not up to date any more: Some changes have occurred and a new, up to date matching co… |
| 1.3.6.1.4.1.22.60.3.10 | ScalarfibTmuMatchNoMatchReason | read-only | mandatory | Indication meaningful only if fibTmuMatchUpToDate above is not up-to-date. empty-reason - Either there is a list or the reason for the fact that there is no li… |
| 1.3.6.1.4.1.22.60.3.20 | TablefibTmuMatchTable | not-accessible | mandatory | Table containing information on the location of stations (identified by their physical address in terms of Tmu/Tau ports). |
| 1.3.6.1.4.1.22.60.3.20.1 | RowfibTmuMatchEntry | not-accessible | mandatory | Entry of information concerning a single station and its port (on Tmu/Tau). |
| 1.3.6.1.4.1.22.60.3.20.1.1 | ColumnfibTmuMatchIndex | read-only | mandatory | The value of this object identifies the the number of the entry in the table. See remark in fibTmuMatchListValid above |
| 1.3.6.1.4.1.22.60.3.20.1.2 | ColumnfibTmuMatchTauId | read-only | mandatory | Number of the tau port on which station is attached. Tau ports are connectors on the tmu. The may have either a tau connected or a single station. See fibTmuMa… |
| 1.3.6.1.4.1.22.60.3.20.1.3 | ColumnfibTmuMatchPortId | read-only | mandatory | If greater than 1 then 'fibTmuMatchTauId' is the number of the port on the tmu and 'fibTmuMatchPortId' is the number of the port on the related Tau (starting w… |
| 1.3.6.1.4.1.22.60.3.20.1.4 | ColumnfibTmuMatchPhysAddr | read-only | mandatory | The token ring physical address of the station which is attached to the specified port. See remark in fibTmuMatchListValid above |
| 1.3.6.1.4.1.22.60.3.20.1.5 | ColumnfibTmuMatchStationInfo | read-only | mandatory | Information on the attached station: If BIT0 is set (value = 0x01) then this is definitely a 'sniffer' port (i.e. a station which is sending 'trace tool presen… |
| 1.3.6.1.4.1.22.60.4 | NodetmuStations | |||
| 1.3.6.1.4.1.22.60.4.1 | ScalarfibTmuStationsUpdateTime | read-only | mandatory | Time [in sys timer units] from startup at which the table below has been updated. See remark in fibTmuStationsListValid below. |
| 1.3.6.1.4.1.22.60.4.2 | ScalarfibTmuStationsNumEntries | read-only | mandatory | Number of meaningful entries in the Stations array. The index of the last meaningful entry is num-entries. See remark in fibTmuStationsListValid below. |
| 1.3.6.1.4.1.22.60.4.3 | ScalarfibTmuStationsNumTmuEntries | read-only | mandatory | Number of meaningful entries in the Stations array which belong to stations attached to the tmu via tau ports. This does not include the two (or one) chipsets … |
| 1.3.6.1.4.1.22.60.4.4 | ScalarfibTmuStationsFirstChipIndex | read-only | mandatory | The index in the Stations table at which the the first chipset is located (order of stations on Stations table is downstream, i.e. in the direction messages ar… |
| 1.3.6.1.4.1.22.60.4.5 | ScalarfibTmuStationsSecondChipIndex | read-only | mandatory | The index in the Stations table at which the the second chipset is located (order of stations on Stations table is downstream, i.e. in the direction messages a… |
| 1.3.6.1.4.1.22.60.4.6 | ScalarfibTmuStationsActMonIndex | read-only | mandatory | The index in the Stations table at which the active monitor is located (order of stations on Stations table is downstream, i.e. in the direction messages are t… |
| 1.3.6.1.4.1.22.60.4.7 | ScalarfibTmuStationsConfigChipIndex | read-only | mandatory | The index in the Stations table from which the information for the configuration was collected (order of stations on Stations table is downstream, i.e. in the … |
| 1.3.6.1.4.1.22.60.4.8 | ScalarfibTmuStationsStationsListValid | read-only | mandatory | Flag indicating whether the information in the tmuStations group is valid or not. If information is not valid, ALL objects will return with a 'no such object' … |
| 1.3.6.1.4.1.22.60.4.9 | ScalarfibTmuStationsUpToDate | read-only | mandatory | Flag. If set '1' then the information in All objects of tmuStations group is not up to date any more: Some changes have occurred and a new, up to date Stations… |
| 1.3.6.1.4.1.22.60.4.10 | ScalarfibTmuMatchNoStationsListReason | read-only | mandatory | Indication meaningful only if fibTmuStationsUpToDate above is not up-to-date. empty-reason - Either there is a list or the reason for the fact that there is no… |
| 1.3.6.1.4.1.22.60.4.20 | TablefibTmuStationsTable | not-accessible | mandatory | Table containing information on the location of stations (identified by their physical address). |
| 1.3.6.1.4.1.22.60.4.20.1 | RowfibTmuStationsEntry | not-accessible | mandatory | Entry of information concerning a single station. |
| 1.3.6.1.4.1.22.60.4.20.1.1 | ColumnfibTmuStationsIndex | read-only | mandatory | The value of this object identifies the the number of the entry in the table. See remark in fibTmuStationsListValid above |
| 1.3.6.1.4.1.22.60.4.20.1.2 | ColumnfibTmuStationsPhysAddr | read-only | mandatory | The token ring physical address of the station which is at the specified index. See remark in fibTmuStationsListValid above |
| 1.3.6.1.4.1.22.60.4.20.1.3 | ColumnfibTmuStationsStationInfo | read-only | mandatory | Information on the attached station: If BIT0 is set (value = 0x01) then this is definitely a 'sniffer' port (i.e. a station which is sending 'trace tool presen… |
| 1.3.6.1.4.1.22.60.5 | NodetmuPorts | |||
| 1.3.6.1.4.1.22.60.5.1 | ScalarfibTmuPortsNumRelayOpen | read-only | mandatory | Number of ports attached to single stations either directly on the tmu or on a tau which have their relay open. A relay remains open as long as there is an att… |
| 1.3.6.1.4.1.22.60.5.2 | ScalarfibTmuPortsNumPhantomPresent | read-only | mandatory | Number of ports attached to single stations (either directly on the tmu or on a tau) which have their phantom up. |
| 1.3.6.1.4.1.22.60.5.3 | ScalarfibTmuPortsNumPortsPerTmu | read-only | mandatory | Number of ports on one tmu (both ports which support a tau and ports which may support only single stations). |
| 1.3.6.1.4.1.22.60.5.4 | ScalarfibTmuPortsNumTausPerTmu | read-only | mandatory | The maximal number of Tau's which can be connected to one Tmu |
| 1.3.6.1.4.1.22.60.5.5 | ScalarfibTmuPortsNumPortsPerTau | read-only | mandatory | The maximal number of ports on one Tau |
| 1.3.6.1.4.1.22.60.5.6 | ScalarfibTmuPortsMaxNumTauErrs | read-only | mandatory | Number of errors (which cause temporary relay closing) allowed after phantom goes up on a single Tau port and before its relay is closed (port detached). Relay… |
| 1.3.6.1.4.1.22.60.5.7 | ScalarfibTmuPortsMaxFirstTimeout | read-only | mandatory | Number of timeouts allowed before it is decided that communication with Tau is really faulty. System moves from state of connection into no-connection and atte… |
| 1.3.6.1.4.1.22.60.5.29 | TablefibTmuPortsTauTable | not-accessible | mandatory | Table containing information on ports which are directly on Tmu and on Tau's which may be connected to them. |
| 1.3.6.1.4.1.22.60.5.29.1 | RowfibTmuPortsTauEntry | not-accessible | mandatory | Entry of information concerning a single port on Tmu and the attached station/Tau. |
| 1.3.6.1.4.1.22.60.5.29.1.1 | ColumnfibTmuPortsTmuPort | read-only | mandatory | Number of port (on TMU) described in this array entry. Port numbers increase in the direction of the token. |
| 1.3.6.1.4.1.22.60.5.29.1.2 | ColumnfibTmuPortsPortType | read-only | mandatory | Flag indicating whether this port supports both a Tau and a single station or just a single station. |
| 1.3.6.1.4.1.22.60.5.29.1.3 | ColumnfibTmuPortsEndConnection | read-only | mandatory | Flag indicating whether this port is connected to a Tau or to a single station (or is in a state where it is not clear exactly what is connected to the specifi… |
| 1.3.6.1.4.1.22.60.5.29.1.4 | ColumnfibTmuPortsPortStatus | read-only | mandatory | Bit map indicating status of the port: Bit3 (0x08) - If set indicates that the relay of this port is open (and, therefore, the station/Tau connected to this po… |
| 1.3.6.1.4.1.22.60.5.29.1.5 | ColumnfibTmuPortsManagerCloseRun | read-write | mandatory | When setting this object to the value of close (2) the indicated port on Tmu will be closed, the related led will start blinking at a slow rate and port will n… |
| 1.3.6.1.4.1.22.60.5.29.1.6 | ColumnfibTmuPortsManagerClosePerm | read-write | mandatory | When setting this object to the value of close (2) the indicated port on Tmu will be closed after the next system reset. see 'fibTmuPortsManagerCloseRun'. Sett… |
| 1.3.6.1.4.1.22.60.5.29.1.10 | ColumnfibTmuPortsNumConsequentErrs | read-only | mandatory | Counter. Number of times an error has been detected on this Tau port (one after the other, without a 'no error' state in between) since phantom last came up. W… |
| 1.3.6.1.4.1.22.60.5.29.1.11 | ColumnfibTmuPortsNumTimeout | read-only | mandatory | Number of times communication with Tau has been attempted immediately after pahntom has gone up. Attempt go on for MaxFirstTimeout times. After that, it is dec… |
| 1.3.6.1.4.1.22.60.5.29.1.12 | ColumnfibTmuPortsTauPortState | read-only | mandatory | This is a status byte. it indicates the state of the port as far as software is concerned. A port which may only carry a single station can possibly be in one … |
| 1.3.6.1.4.1.22.60.5.29.1.13 | ColumnfibTmuPortsNumPorts | read-only | mandatory | The number of ports on the Tau connected to this port. Set to '1' when a station is directly connected to this port. Only meaningful when 'fibTmuPortsTauPortSt… |
| 1.3.6.1.4.1.22.60.5.29.1.14 | ColumnfibTmuPortsNumAttached | read-only | mandatory | This is the number of ports on the connected Tau (if there is any) that have their relay open (station is attached to the ring). Only meaningful when 'fibTmuPo… |
| 1.3.6.1.4.1.22.60.5.29.1.15 | ColumnfibTmuPortsNumPhantomUp | read-only | mandatory | This is the number of ports on the connected Tau (if there is any) that have their phantom in 'up' state. Only meaningful when 'fibTmuPortsTauPortState' is 'ac… |
| 1.3.6.1.4.1.22.60.5.29.1.16 | ColumnfibTmuPortsTauRevision | read-only | mandatory | This is the Tau revision as reported by the Tau itself (if there is one). Only meaningful when 'fibTmuPortsTauPortState' is 'active-connection'. |
| 1.3.6.1.4.1.22.60.5.29.1.17 | ColumnfibTmuPortsModuleId | read-only | mandatory | This is a hw id attached to each of its modules by the Tau. each octet is related to one module (up to 4 modules). Number of meaningful octets is determined by… |
| 1.3.6.1.4.1.22.60.5.29.1.18 | ColumnfibTmuPortsNumModules | read-only | mandatory | This is the number of modules on the attached Tau as reported by the Tau itself. Only meaningful when 'fibTmuPortsTauPortState' is 'active-connection'. |
| 1.3.6.1.4.1.22.60.5.29.1.19 | ColumnfibTmuPortsTauMode | read-only | mandatory | This is a bit map of information on the status of the Tau and the way it is set. Details of the various bits: Bit0 (= 0x01) If '1' then Tau is set to a rate of… |
| 1.3.6.1.4.1.22.60.5.29.1.20 | ColumnfibTmuPortsLedState | read-only | mandatory | State of the indication led related to this port. Values can be: slow-rate (1) fast-rate (2) fixed-on (3) fixed-off (4) |
| 1.3.6.1.4.1.22.60.5.29.1.21 | ColumnfibTmuPortsRequestType | read-only | mandatory | This is the type of the message sent to the attached Tau for which a response is required. If request-type is 'no-Tau-msg' then no message was sent and, theref… |
| 1.3.6.1.4.1.22.60.5.29.1.22 | ColumnfibTmuPortsLastTxTime | read-only | mandatory | This is the system timer value at the last tx-to-Tau on this Tau port (provided a Tau is attached to it). |
| 1.3.6.1.4.1.22.60.5.29.1.23 | ColumnfibTmuPortsLastPollTime | read-only | mandatory | This is the system timer value at the last poll response on this Tau port (provided a Tau is attached to it). If no polling has so far been carried out, a valu… |
| 1.3.6.1.4.1.22.60.5.29.1.24 | ColumnfibTmuPortsUpdateTime | read-only | mandatory | This is the system timer value when phantom was last probed on this Tau port. |
| 1.3.6.1.4.1.22.60.5.29.1.25 | ColumnfibTmuPortsAllowedAddr | read-write | mandatory | This is the one physical address allowed to be on this Tmu port (provided a single station is attached to it and not a Tau). The value loaded in fibTmuPortsAll… |
| 1.3.6.1.4.1.22.60.5.29.1.26 | ColumnfibTmuPortsAllowedAddrLoaded | read-write | mandatory | This is the status of fibTmuPortsAllowedAddr. When reading, the possible values are as follows: addr-not-loaded indicates the value in fibTmuPortsAllowedAddr i… |
| 1.3.6.1.4.1.22.60.5.30 | TablefibTmuPortsAllTable | not-accessible | mandatory | Table containing information on ports which are directly connected to stations and on Tau ports which may be connected to stations. |
| 1.3.6.1.4.1.22.60.5.30.1 | RowfibTmuPortsAllEntry | not-accessible | mandatory | Entry of information concerning a single port on Tmu or on Tau. |
| 1.3.6.1.4.1.22.60.5.30.1.1 | ColumnfibTmuPortsTmuPortIndex | read-only | mandatory | Number of port on Tmu. Port numbers increase in the direction of the token. range of valid values: 1->fibTmuPortsNumTausPerTmu |
| 1.3.6.1.4.1.22.60.5.30.1.2 | ColumnfibTmuPortsTauPortIndex | read-only | mandatory | Number of port on Tau. Port numbers increase in the direction of the token. range of valid values: 1->fibTmuPortsNumTausPerTau |
| 1.3.6.1.4.1.22.60.5.30.1.3 | ColumnfibTmuPortsPortState | read-only | mandatory | Bit map describing the indicated port: Bit1 (0x02) - No such port. Index is out of bounds. Either a Tau is connected and the specified port number is larger th… |
| 1.3.6.1.4.1.22.60.5.30.1.4 | ColumnfibTmuPortsGenCloseRun | read-write | mandatory | When setting this object to the value of close (2) the indicated port on Tau will be closed, the related led will start blinking at a slow rate and port will n… |
| 1.3.6.1.4.1.22.60.5.30.1.5 | ColumnfibTmuPortsGenClosePerm | read-write | mandatory | When setting this object to the value of close (2) the indicated port on Tau is instructed to be closed after the next reset. Setting to the value of open (1) … |
| 1.3.6.1.4.1.22.60.5.30.1.6 | ColumnfibTmuPortsPhysAddr | read-only | mandatory | The token ring physical address of the station which is attached to the specified port. If station is not identified (e.g. fibTmuMatchListValid, see above, is … |
| 1.3.6.1.4.1.22.60.5.30.1.7 | ColumnfibTmuPortsStationInfo | read-only | mandatory | Information on the attached station: If BIT0 is set (value = 0x01) then this is definitely a 'sniffer' port (i.e. a station which is sending 'trace tool presen… |
| 1.3.6.1.4.1.22.60.5.30.1.8 | ColumnfibTmuPortsTauAllowedAddr | read-write | mandatory | This is the one physical address allowed to be on this port on Tau. The value loaded in fibTmuPortsTauAllowedAddrLoaded below determines the state of this obje… |
| 1.3.6.1.4.1.22.60.5.30.1.9 | ColumnfibTmuPortsTauAllowedAddrLoaded | read-write | mandatory | This is the status of fibTmuPortsTauAllowedAddr. When reading, the possible values are as follows: addr-not-loaded indicates the value in fibTmuPortsTauAllowed… |
| 1.3.6.1.4.1.22.60.6 | NodetmuProduction | |||
| 1.3.6.1.4.1.22.60.6.1 | ScalarfibTmuProductionAddr48No1 | read-write | mandatory | 48 bit address of the chip set which is located at the primary in port. |
| 1.3.6.1.4.1.22.60.6.2 | ScalarfibTmuProductionAddr48No2 | read-write | mandatory | 48 bit address of the chip set which is located at the primary out port. |
| 1.3.6.1.4.1.22.60.6.3 | ScalarfibTmuProductionAddr48No3 | read-write | mandatory | 48 bit address of the chip set which is located at the secondary ring port. |
| 1.3.6.1.4.1.22.60.6.4 | ScalarfibTmuProductionRomType | read-write | mandatory | Type of EPROM used in the Tmu system. |
| 1.3.6.1.4.1.22.60.6.5 | ScalarfibTmuProductionRamType | read-write | mandatory | Type of RAM used in the Tmu system. |
| 1.3.6.1.4.1.22.60.6.6 | ScalarfibTmuProductionFlashType | read-write | mandatory | Type of FLASH used in the Tmu system. |
| 1.3.6.1.4.1.22.60.6.7 | ScalarfibTmuProductionEepromType | read-write | mandatory | Type of EEPROM used in the Tmu system. |
| 1.3.6.1.4.1.22.60.6.8 | ScalarfibTmuProductionSerialNum | read-write | mandatory | Serial number of Tmu HW system. |
| 1.3.6.1.4.1.22.60.6.9 | ScalarfibTmuProductionRamSize | read-write | mandatory | Size of RAM used in the Tmu system in units of 32K bytes. A value of '3' indicates size is not known. |
| 1.3.6.1.4.1.22.60.6.10 | ScalarfibTmuProductionFlash0Size | read-write | mandatory | Size of FLASH memory bank #0 used in the Tmu system in units of 32K bytes. A value of '3' indicates size is not known. |
| 1.3.6.1.4.1.22.60.6.11 | ScalarfibTmuProductionFlash1Size | read-write | mandatory | Size of FLASH memory bank #1 used in the Tmu system in units of 32K bytes. A value of '3' indicates size is not known. A value of '2' indicates chip is not ins… |
| 1.3.6.1.4.1.22.60.6.12 | ScalarfibTmuProductionEepromSize | read-write | mandatory | Size of EEPROM memory used in the Tmu system in units of 0.5K bytes. A value of '3' indicates size is not known. |
| 1.3.6.1.4.1.22.60.6.13 | ScalarfibTmuProductionHwInfo | read-write | mandatory | General encoded information concerning Tmu system's hardware. |
| 1.3.6.1.4.1.22.60.6.14 | ScalarfibTmuProductionBoardType | read-only | mandatory | Type of TMU Board. |
| 1.3.6.1.4.1.22.60.7 | NodetmuSecurity | |||
| 1.3.6.1.4.1.22.60.7.1 | ScalarfibTmuSecurityModeRun | read-only | mandatory | The currently effective security mode. This is a bit map. This object is only loaded once after reset. To change it, fibTmuSecurityModeRun must be loaded and t… |
| 1.3.6.1.4.1.22.60.7.2 | ScalarfibTmuSecurityModePerm | read-write | mandatory | The value currently in non volatile memory of the security mode. This is a bit map. See detals in fibTmuSecurityModeRun above. This object is only loaded into … |
| 1.3.6.1.4.1.22.60.7.3 | ScalarfibTmuNumStationSecurity | read-only | mandatory | Maximal number of ports for which the security mode 'station security' (see fibTmuSecurityModeRun above) can be specified. |
| 1.3.6.1.4.1.22.60.7.4 | ScalarfibTmuNumStationLeft | read-only | mandatory | Number of ports for which the security mode 'station security' (see fibTmuSecurityModeRun above) can still be specified. This is the difference between 'fibTmu… |
| 1.3.6.1.4.1.22.60.8 | NodetmuFunction | |||
| 1.3.6.1.4.1.22.60.8.1 | NodefibTmuFunctRtpGrpVrsRun | |||
| 1.3.6.1.4.1.22.60.8.1.1 | ScalarfibTmuFunctBeacon2AutotestRun | read-only | mandatory | The time period for starting the 'autoremove' test after start of beaconing. In units of milliseconds. Minimal value: 160. maximal value 200. Factory default: … |
| 1.3.6.1.4.1.22.60.8.1.2 | ScalarfibTmuFunctBeacon2OkRun | read-only | mandatory | The upper bound for time period starting at the removal of a problem till ring status indicates no beaconing. In units of milliseconds. Minimal value: 40. maxi… |
| 1.3.6.1.4.1.22.60.8.1.3 | ScalarfibTmuFunctOk2BeaconRun | read-only | mandatory | The upper bound for time period starting at the insertion of a problem till ring status indicates beaconing. In units of milliseconds. Minimal value: 1100. max… |
| 1.3.6.1.4.1.22.60.8.1.4 | ScalarfibTmuFunctWrapCwtRun | read-only | mandatory | Time delay to apply, after changing warp relay state. In units of milliseconds. Intended to let TMS get the real ring status. Minimal value: 0. maximal value 2… |
| 1.3.6.1.4.1.22.60.8.1.5 | ScalarfibTmuFunctWrapWnrRun | read-only | mandatory | Flag indicating whether to release CPU while waiting after warp change. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE. To change this object, load 'fibTmu… |
| 1.3.6.1.4.1.22.60.8.1.6 | ScalarfibTmuFunctRingIstRun | read-only | mandatory | Time to poll for consistent Tmu ring status before continuing recovery. In units of milliseconds. Minimal value: 0. maximal value 200. Factory default: 0 To ch… |
| 1.3.6.1.4.1.22.60.8.1.7 | ScalarfibTmuFunctRingIstnrRun | read-only | mandatory | Flag indicating whether to release CPU while waiting for consistent Tmu ring status. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE. To change this object,… |
| 1.3.6.1.4.1.22.60.8.1.8 | ScalarfibTmuFunctCheckAogTauRun | read-only | mandatory | Flag is used during BRUTAL recovery (single problem). If TRUE (checck-ring) then check whether the ring is BEACONING after opening the good TAU's (This check t… |
| 1.3.6.1.4.1.22.60.8.1.9 | ScalarfibTmuFunctMaxNoiRun | read-only | mandatory | When several station wants to insert into the ring, this parameter sets the limit on the maximal number of stations which are allowed to insert (other stations… |
| 1.3.6.1.4.1.22.60.8.1.10 | ScalarfibTmuFunctLinkPtifRun | read-only | mandatory | When problem in TMU segment is discovered then if this flag is TRUE, first of all try to find problem between last inserted stations. Values: 1 - FALSE, 2 - TR… |
| 1.3.6.1.4.1.22.60.8.1.11 | ScalarfibTmuFunctInsPatRun | read-only | mandatory | Parameter for controlling the aging of the 'inseretion-pool' (Should be long enough to make sure that the station is not malfunctioning). Units: milli seconds.… |
| 1.3.6.1.4.1.22.60.8.1.12 | ScalarfibTmuFunctUseMismatchRun | read-only | mandatory | Indication on whether to apply recovery when the number of stations is larger than the number of open ports. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE… |
| 1.3.6.1.4.1.22.60.8.1.13 | ScalarfibTmuFunctChkRingInsRun | read-only | mandatory | Indication on whether to check ring status (for possible problems caused by the currently inserted stations) or not. Setting 'TRUE' results in quicker discover… |
| 1.3.6.1.4.1.22.60.8.1.14 | ScalarfibTmuFunctChkRingPerRun | read-only | mandatory | Parameter indicating the elapsed time after letting a station into the ring after which a station is considered to be o.k. See 'fibTmuFunctChkRingInsRun' Units… |
| 1.3.6.1.4.1.22.60.8.1.15 | ScalarfibTmuFunctClaimTimeOutRun | read-only | mandatory | Parameter indicating the elapsed time between the detection of a problem and the beginning of sending 'claim'. Units: milli seconds. Minimal value: 150. maxima… |
| 1.3.6.1.4.1.22.60.8.1.16 | ScalarfibTmuFunctAnotherCheckRun | read-only | mandatory | Indication on whether to perform another check before disabling a port as a cross check. Values: 1 - FALSE, 2 - TRUE. Factory default: FALSE. To change this ob… |
| 1.3.6.1.4.1.22.60.8.1.17 | ScalarfibTmuFunctTmsOnOutRun | read-only | mandatory | Parameter indicating the tms to leave out of the ring when carrying out 'warp out': It could be TMS no. 2 (TMS OUT) or the TMS which is on the secondary ring. … |
| 1.3.6.1.4.1.22.60.8.1.18 | ScalarfibTmuFunctUseJitterRun | read-only | mandatory | Indication on whether to use the jitter buster hardware module or not. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE. To change this object, load 'fibTmuF… |
| 1.3.6.1.4.1.22.60.8.1.21 | ScalarfibTmuFunctForceStpRiRun | read-only | mandatory | This object is used to control the type of the trunk (OPTIC or STP). Algorithm: if (optic-module-exists && do-not-force-ri-stp) { ri-trunk-type = OPTIC ; } els… |
| 1.3.6.1.4.1.22.60.8.1.22 | ScalarfibTmuFunctForceStpRoRun | read-only | mandatory | This object is used to control the type of the trunk (OPTIC or STP). Algorithm: if (optic-module-exists && do-not-force-ro-stp) { ro-trunk-type = OPTIC ; } els… |
| 1.3.6.1.4.1.22.60.8.1.23 | ScalarfibTmuFunctMaxSavRecRun | read-only | mandatory | Parameter indicating how many elements to save in the fifo buffer of containing the history of recovery. Minimal value: 5. maximal value 20. Factory default: 2… |
| 1.3.6.1.4.1.22.60.8.1.24 | ScalarfibTmuFunctReadPerRun | read-only | mandatory | Parameter indicating the elapsed time between two readings of the error counter of a TMS. Too large a period may result in counter overflow. A value of '0' ind… |
| 1.3.6.1.4.1.22.60.8.1.25 | ScalarfibTmuFunctDmaThreshRun | read-only | mandatory | Parameter indicating the number of times DMA will attempt retry in case of bus error before giving up. Minimal value: 0. maximal value 30. Factory default: 30.… |
| 1.3.6.1.4.1.22.60.8.1.26 | ScalarfibTmuFunctRemWrapTypeRun | read-only | mandatory | Parameter indicating the criterion for removing 'wrap': It could be removed when the ring is not beaconing and it could be removed when the ring is not claimin… |
| 1.3.6.1.4.1.22.60.8.1.27 | ScalarfibTmuFunctRemWrapLenRun | read-only | mandatory | Parameter indicating the elapsed time between the time it is decided that wrap can be removed and the actual removal. See 'fibTmuFunctRemWrapTypeRun'. Units: m… |
| 1.3.6.1.4.1.22.60.8.2 | NodefibTmuFunctRtpGrpVrsPerm | |||
| 1.3.6.1.4.1.22.60.8.2.1 | ScalarfibTmuFunctBeacon2AutotestPerm | read-write | mandatory | The time period for starting the 'autoremove' test after start of beaconing. In units of milliseconds. Minimal value: 160. maximal value 200. Factory default: … |
| 1.3.6.1.4.1.22.60.8.2.2 | ScalarfibTmuFunctBeacon2OkPerm | read-write | mandatory | The upper bound for time period starting at the removal of a problem till ring status indicates no beaconing. In units of milliseconds. Minimal value: 40. maxi… |
| 1.3.6.1.4.1.22.60.8.2.3 | ScalarfibTmuFunctOk2BeaconPerm | read-write | mandatory | The upper bound for time period starting at the insertion of a problem till ring status indicates beaconing. In units of milliseconds. Minimal value: 1100. max… |
| 1.3.6.1.4.1.22.60.8.2.4 | ScalarfibTmuFunctWrapCwtPerm | read-write | mandatory | Time delay to apply, after changing warp relay state. In units of milliseconds. Intended to let TMS get the real ring status. Minimal value: 0. maximal value 2… |
| 1.3.6.1.4.1.22.60.8.2.5 | ScalarfibTmuFunctWrapWnrPerm | read-write | mandatory | Flag indicating whether to release CPU while waiting after warp change. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE. Setting this variable loads it into… |
| 1.3.6.1.4.1.22.60.8.2.6 | ScalarfibTmuFunctRingIstPerm | read-write | mandatory | Time to poll for consistent Tmu ring status before continuing recovery. In units of milliseconds. Minimal value: 0. maximal value 200. Factory default: 0 Setti… |
| 1.3.6.1.4.1.22.60.8.2.7 | ScalarfibTmuFunctRingIstnrPerm | read-write | mandatory | Flag indicating whether to release CPU while waiting for consistent Tmu ring status. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE. Setting this variable … |
| 1.3.6.1.4.1.22.60.8.2.8 | ScalarfibTmuFunctCheckAogTauPerm | read-write | mandatory | Flag is used during BRUTAL recovery (single problem). If TRUE (checck-ring) then check whether the ring is BEACONING after opening the good TAU's (This check t… |
| 1.3.6.1.4.1.22.60.8.2.9 | ScalarfibTmuFunctMaxNoiPerm | read-write | mandatory | When several station wants to insert into the ring, this parameter sets the limit on the maximal number of stations which are allowed to insert (other stations… |
| 1.3.6.1.4.1.22.60.8.2.10 | ScalarfibTmuFunctLinkPtifPerm | read-write | mandatory | When problem in TMU segment is discovered then if this flag is TRUE, first of all try to find problem between last inserted stations. Values: 1 - FALSE, 2 - TR… |
| 1.3.6.1.4.1.22.60.8.2.11 | ScalarfibTmuFunctInsPatPerm | read-write | mandatory | Parameter for controlling the aging of the 'inseretion-pool' (Should be long enough to make sure that the station is not malfunctioning). Units: milli seconds.… |
| 1.3.6.1.4.1.22.60.8.2.12 | ScalarfibTmuFunctUseMismatchPerm | read-write | mandatory | Indication on whether to apply recovery when the number of stations is larger than the number of open ports. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE… |
| 1.3.6.1.4.1.22.60.8.2.13 | ScalarfibTmuFunctChkRingInsPerm | read-write | mandatory | Indication on whether to check ring status (for possible problems caused by the currently inserted stations) or not. Setting 'TRUE' results in quicker discover… |
| 1.3.6.1.4.1.22.60.8.2.14 | ScalarfibTmuFunctChkRingPerPerm | read-write | mandatory | Parameter indicating the elapsed time after letting a station into the ring after which a station is considered to be o.k. See 'fibTmuFunctChkRingInsPerm' Unit… |
| 1.3.6.1.4.1.22.60.8.2.15 | ScalarfibTmuFunctClaimTimeOutPerm | read-write | mandatory | Parameter indicating the elapsed time between the detection of a problem and the beginning of sending 'claim'. Units: milli seconds. Minimal value: 150. maxima… |
| 1.3.6.1.4.1.22.60.8.2.16 | ScalarfibTmuFunctAnotherCheckPerm | read-write | mandatory | Indication on whether to perform another check before disabling a port as a cross check. Values: 1 - FALSE, 2 - TRUE. Factory default: FALSE. Setting this vari… |
| 1.3.6.1.4.1.22.60.8.2.17 | ScalarfibTmuFunctTmsOnOutPerm | read-write | mandatory | Parameter indicating the tms to leave out of the ring when carrying out 'warp out': It could be TMS no. 2 (TMS OUT) or the TMS which is on the secondary ring. … |
| 1.3.6.1.4.1.22.60.8.2.18 | ScalarfibTmuFunctUseJitterPerm | read-write | mandatory | Indication on whether to use the jitter buster hardware module or not. Values: 1 - FALSE, 2 - TRUE. Factory default: TRUE. Setting this variable loads it into … |
| 1.3.6.1.4.1.22.60.8.2.21 | ScalarfibTmuFunctForceStpRiPerm | read-write | mandatory | This object is used to control the type of the trunk (OPTIC or STP). Algorithm: if (optic-module-exists && do-not-force-ri-stp) { ri-trunk-type = OPTIC ; } els… |
| 1.3.6.1.4.1.22.60.8.2.22 | ScalarfibTmuFunctForceStpRoPerm | read-write | mandatory | This object is used to control the type of the trunk (OPTIC or STP). Algorithm: if (optic-module-exists && do-not-force-ro-stp) { ro-trunk-type = OPTIC ; } els… |
| 1.3.6.1.4.1.22.60.8.2.23 | ScalarfibTmuFunctMaxSavRecPerm | read-write | mandatory | Parameter indicating how many elements to save in the fifo buffer of containing the history of recovery. Minimal value: 5. maximal value 20. Factory default: 2… |
| 1.3.6.1.4.1.22.60.8.2.24 | ScalarfibTmuFunctReadPerPerm | read-write | mandatory | Parameter indicating the elapsed time between two readings of the error counter of a TMS. Too large a period may result in counter overflow. A value of '0' ind… |
| 1.3.6.1.4.1.22.60.8.2.25 | ScalarfibTmuFunctDmaThreshPerm | read-write | mandatory | Parameter indicating the number of times DMA will attempt retry in case of bus error before giving up. Minimal value: 0. maximal value 30. Factory default: 30.… |
| 1.3.6.1.4.1.22.60.8.2.26 | ScalarfibTmuFunctRemWrapTypePerm | read-write | mandatory | Parameter indicating the criterion for removing 'wrap': It could be removed when the ring is not beaconing and it could be removed when the ring is not claimin… |
| 1.3.6.1.4.1.22.60.8.2.27 | ScalarfibTmuFunctRemWrapLenPerm | read-write | mandatory | Parameter indicating the elapsed time between the time it is decided that wrap can be removed and the actual removal. See 'fibTmuFunctRemWrapTypePerm'. Units: … |