TNI-MIB
446 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868 | Nodetransition | |||
| 1.3.6.1.4.1.868.1 | NodeproductId | |||
| 1.3.6.1.4.1.868.1 | NodetnIntruderDetect | The tnIntruderDetect trap conveys information related to the automatic intrusion detection of the SPS2000. This trap is sent when an intruder is detected. | ||
| 1.3.6.1.4.1.868.1.1 | NoderptrProdsId | |||
| 1.3.6.1.4.1.868.1.1.1 | NoderptrStackMId | |||
| 1.3.6.1.4.1.868.1.1.1.1 | NoderptrSMVer1Id | |||
| 1.3.6.1.4.1.868.1.1.1.2 | NoderptrSMVer2Id | |||
| 1.3.6.1.4.1.868.1.1.1.3 | NoderptrSM08TId | |||
| 1.3.6.1.4.1.868.1.1.1.4 | NoderptrSM08TSId | |||
| 1.3.6.1.4.1.868.1.1.1.5 | NoderptrSM06FId | |||
| 1.3.6.1.4.1.868.1.1.1.6 | NoderptrSM06FSId | |||
| 1.3.6.1.4.1.868.1.1.1.7 | NoderptrSM8T0Id | |||
| 1.3.6.1.4.1.868.1.1.1.8 | NoderptrSM8TS0Id | |||
| 1.3.6.1.4.1.868.1.1.1.9 | NoderptrSM6F0Id | |||
| 1.3.6.1.4.1.868.1.1.1.10 | NoderptrSM6FS0Id | |||
| 1.3.6.1.4.1.868.1.1.1.11 | NoderptrSM8T6FId | |||
| 1.3.6.1.4.1.868.1.1.1.12 | NoderptrSM8TS6FId | |||
| 1.3.6.1.4.1.868.1.1.1.13 | NoderptrSM8T6FSId | |||
| 1.3.6.1.4.1.868.1.1.1.14 | NoderptrSM8TS6FSId | |||
| 1.3.6.1.4.1.868.1.1.1.15 | NoderptrSM6F8TId | |||
| 1.3.6.1.4.1.868.1.1.1.16 | NoderptrSM6FS8TId | |||
| 1.3.6.1.4.1.868.1.1.1.17 | NoderptrSM6F8TSId | |||
| 1.3.6.1.4.1.868.1.1.1.18 | NoderptrSM6FS8TSId | |||
| 1.3.6.1.4.1.868.1.1.1.19 | NoderptrSM8T8TId | |||
| 1.3.6.1.4.1.868.1.1.1.20 | NoderptrSM8TS8TId | |||
| 1.3.6.1.4.1.868.1.1.1.21 | NoderptrSM8T8TSId | |||
| 1.3.6.1.4.1.868.1.1.1.22 | NoderptrSM8TS8TSId | |||
| 1.3.6.1.4.1.868.1.1.1.23 | NoderptrSM6F6FId | |||
| 1.3.6.1.4.1.868.1.1.1.24 | NoderptrSM6FS6FId | |||
| 1.3.6.1.4.1.868.1.1.1.25 | NoderptrSM6F6FSId | |||
| 1.3.6.1.4.1.868.1.1.1.26 | NoderptrSM6FS6FSId | |||
| 1.3.6.1.4.1.868.1.1.1.27 | NoderptrSM24TId | |||
| 1.3.6.1.4.1.868.1.1.1.28 | NoderptrSM16TId | |||
| 1.3.6.1.4.1.868.1.1.1.29 | NoderptrSM14FId | |||
| 1.3.6.1.4.1.868.1.1.1.30 | NoderptrSM12FId | |||
| 1.3.6.1.4.1.868.1.1.1.31 | NoderptrSM6FId | |||
| 1.3.6.1.4.1.868.1.1.1.32 | NoderptrSM0Id | |||
| 1.3.6.1.4.1.868.1.1.2 | NoderptrSPSId | |||
| 1.3.6.1.4.1.868.1.1.2.1 | NoderptrSPSVer1Id | |||
| 1.3.6.1.4.1.868.1.1.2.2 | NoderptrESPS24Id | |||
| 1.3.6.1.4.1.868.1.1.2.3 | NoderptrESPS24SId | |||
| 1.3.6.1.4.1.868.1.2 | NoderingProdsId | |||
| 1.3.6.1.4.1.868.1.2.1 | NoderingStackTRId | |||
| 1.3.6.1.4.1.868.1.2.1.1 | NoderingTRVer1Id | |||
| 1.3.6.1.4.1.868.1.2.1.2 | NoderingTRVer2Id | |||
| 1.3.6.1.4.1.868.1.2.1.3 | NoderingTR0Id | |||
| 1.3.6.1.4.1.868.1.2.1.4 | NoderingTR16TId | |||
| 1.3.6.1.4.1.868.1.3 | NodebrdgProdsId | |||
| 1.3.6.1.4.1.868.1.3.1 | NodebrdgSwitchMId | |||
| 1.3.6.1.4.1.868.1.3.1.1 | NodebrdgSWVer1Id | |||
| 1.3.6.1.4.1.868.1.3.2 | NodebrdgFBRMId | |||
| 1.3.6.1.4.1.868.1.3.2.119 | Nodesfbrm100ATUDbFull | The Address Translation Database is full, no more entries can be added. | ||
| 1.3.6.1.4.1.868.1.3.2.120 | Nodesfbrm100VTUMemberViolation | A Frame with VLAN ID found in the VLAN Table has been received, but the Ingress port is not a member of the VLAN. | ||
| 1.3.6.1.4.1.868.1.3.2.121 | Nodesfbrm100VTUMissViolation | A Frame with a VLAN ID not in VLAN Table is received. | ||
| 1.3.6.1.4.1.868.1.3.2.122 | Nodesfbrm100ATUMemberViolation | A Source address look-up in the Address Database finds a entry but the ingress port is not on the list of source port. | ||
| 1.3.6.1.4.1.868.1.3.2.123 | Nodesfbrm100ATUMissViolation | A source address look-up in the Address Database resulted in a miss. | ||
| 1.3.6.1.4.1.868.1.3.2.124 | Nodesfbrm100OAMRemoteDetected | A OAM peer is detected and active OAM communication is established with the Peer. | ||
| 1.3.6.1.4.1.868.1.3.2.125 | Nodesfbrm100EEPROMOnFiber | EEPROM for monitoring, is detected on this port. | ||
| 1.3.6.1.4.1.868.1.3.2.126 | Nodesfbrm100DMIOnFiber | DMI is detected on this port. | ||
| 1.3.6.1.4.1.868.1.3.2.127 | Nodesfbrm100LinkChanged | A Link Status change occurred. | ||
| 1.3.6.1.4.1.868.1.3.2.128 | Nodesfbrm100DMILowRxIntrusion | Intrusion detected on Rx Power. | ||
| 1.3.6.1.4.1.868.1.3.2.129 | Nodesfbrm100DMILowRxPower | Rx Power Alarm. | ||
| 1.3.6.1.4.1.868.1.3.2.130 | Nodesfbrm100DMILowTxPower | Tx Power Alarm. | ||
| 1.3.6.1.4.1.868.1.3.2.131 | Nodesfbrm100DMILowTxBias | Transmit bias alarm. | ||
| 1.3.6.1.4.1.868.1.3.2.132 | Nodesfbrm100DMILowTemperature | Temperature alarm. | ||
| 1.3.6.1.4.1.868.1.3.2.133 | Nodesfbrm100LastGasp | The Last gasp from the local device. | ||
| 1.3.6.1.4.1.868.1.3.2.134 | Nodesfbrm100OAMPeerLinkDown | The remote port is down on the peer. | ||
| 1.3.6.1.4.1.868.1.3.2.135 | Nodesfbrm100OAMPeerLinkUp | The remote port is up on the peer. | ||
| 1.3.6.1.4.1.868.1.3.2.136 | Nodesfbrm100OAMPeerDyingGasp | The remote peer OAM dying gasp trap. | ||
| 1.3.6.1.4.1.868.1.3.2.137 | Nodesfbrm100OAMThresholdEvent | Local/remote peer's OAM Threshold crossing traps. | ||
| 1.3.6.1.4.1.868.1.3.2.138 | Nodesfbrm100PeerVersionMismatch | The remote peer is running a different firmware than local. The remote peer needs upgrading. | ||
| 1.3.6.1.4.1.868.2 | Nodeproducts | |||
| 1.3.6.1.4.1.868.2.1 | Noderepeater | |||
| 1.3.6.1.4.1.868.2.1.1 | NodetnStackM | |||
| 1.3.6.1.4.1.868.2.1.1.1 | NodetnSMCommon | |||
| 1.3.6.1.4.1.868.2.1.1.1.1 | ScalartnSMComHwReset | read-write | mandatory | Perform a hardware reset. |
| 1.3.6.1.4.1.868.2.1.1.1.2 | ScalartnSMComMgmtHwRev | read-only | mandatory | The management h/w board revision. |
| 1.3.6.1.4.1.868.2.1.1.1.3 | ScalartnSMComDiagSwRev | read-only | mandatory | The diagnostic s/w code revision. |
| 1.3.6.1.4.1.868.2.1.1.1.4 | ScalartnSMComMgmtSwRev | read-only | mandatory | The downloadable management s/w code revision. |
| 1.3.6.1.4.1.868.2.1.1.1.5 | ScalartnSMComIpAddr | read-write | mandatory | The IP address to which this entry's addressing information pertains. |
| 1.3.6.1.4.1.868.2.1.1.1.6 | ScalartnSMComNetMask | read-write | mandatory | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits … |
| 1.3.6.1.4.1.868.2.1.1.2 | NodetnSMVer1 | |||
| 1.3.6.1.4.1.868.2.1.1.3 | NodetnSMVer2 | |||
| 1.3.6.1.4.1.868.2.1.2 | Nodesps | |||
| 1.3.6.1.4.1.868.2.1.2.1 | NodespsCommon | |||
| 1.3.6.1.4.1.868.2.1.2.1.1 | ScalarspsReset | read-write | mandatory | Setting this object to reset(2) causes a reset of the hardware. Setting this object to noReset(1) has no effect. The agent will always return the value noReset… |
| 1.3.6.1.4.1.868.2.1.2.1.2 | ScalarspsConfig | read-only | mandatory | The hardware configuration information. The type and size of ROM, RAM, and DRAM. |
| 1.3.6.1.4.1.868.2.1.2.1.3 | ScalarspsBootpEnable | read-only | mandatory | If this object is set to enabled(1) the unit will use the Bootstrap Protocol (BOOTP) on power-up or reset to obtain its IP configuration parameters. If this ob… |
| 1.3.6.1.4.1.868.2.1.2.1.4 | ScalarspsBootpServer | read-only | mandatory | This object specifies the IP address of the BOOTP server the client wishes to respond; forcing the boot to occur from a specific host. If the IP address of the… |
| 1.3.6.1.4.1.868.2.1.2.1.5 | ScalarspsBootpFilename | read-only | mandatory | The 'generic' filename to be booted. |
| 1.3.6.1.4.1.868.2.1.2.1.6 | ScalarspsDefaultGateway | read-write | mandatory | This object specifies the IP address of the default gateway. This object is the same as ipRouteDest for the default route. It is placed here as a single object… |
| 1.3.6.1.4.1.868.2.1.2.1.7 | ScalarspsMgmtSegment | read-write | mandatory | Indicates the segment the management interface is on. The value is between 1 and spsMaxSegment. The agent should not allow the NMU to be placed on a segment wh… |
| 1.3.6.1.4.1.868.2.1.2.1.8 | TablespsIpAddrTable | not-accessible | mandatory | The table of addressing information relevant to this entity's IP addresses. |
| 1.3.6.1.4.1.868.2.1.2.1.8.1 | RowspsIpAddrEntry | not-accessible | mandatory | The addressing information relevant to this entity's IP addresses. |
| 1.3.6.1.4.1.868.2.1.2.1.8.1.1 | ColumnspsIpIfIndex | read-only | mandatory | The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the … |
| 1.3.6.1.4.1.868.2.1.2.1.8.1.2 | ColumnspsIpAddr | read-write | mandatory | The IP address to which this entry's addressing information pertains. The IP address value for this entry is the same value as specified by ipAdEntAddr. This e… |
| 1.3.6.1.4.1.868.2.1.2.1.8.1.3 | ColumnspsIpNetMask | read-write | mandatory | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits … |
| 1.3.6.1.4.1.868.2.1.2.1.9 | TablespsTrapTable | not-accessible | mandatory | A list of trap destinations and community names. When generating a trap, each destination in this list is sent the trap using the associated community name. |
| 1.3.6.1.4.1.868.2.1.2.1.9.1 | RowspsTrapEntry | not-accessible | mandatory | An entry in the spsTrapTable. |
| 1.3.6.1.4.1.868.2.1.2.1.9.1.1 | ColumnspsTrapIndex | read-only | mandatory | The index value which uniquely identifies the SNMP trap destination and community name pairing to which this entry is applicable. |
| 1.3.6.1.4.1.868.2.1.2.1.9.1.2 | ColumnspsTrapDestination | read-write | mandatory | This object specifies the destination address of the Trap-PDU. |
| 1.3.6.1.4.1.868.2.1.2.1.9.1.3 | ColumnspsTrapCommunity | read-write | mandatory | The community name used when generating traps. |
| 1.3.6.1.4.1.868.2.1.2.2 | NodespsVer1 | |||
| 1.3.6.1.4.1.868.2.1.2.2.1 | ScalarspsMaxSegment | read-only | mandatory | The maximum number of segments supported. |
| 1.3.6.1.4.1.868.2.1.2.2.2 | ScalarspsPasswdReset | read-write | mandatory | If this object is set to reset(2) resets the joystick password to a known value. Setting this value to noReset(1) has no effect. The agent will always return t… |
| 1.3.6.1.4.1.868.2.1.2.2.3 | ScalarspsExternalPowerSupply | read-only | mandatory | This object indicates the status of the internal power supply. A value of present(1) indicates the power supply is present and able to provide power. A value o… |
| 1.3.6.1.4.1.868.2.1.2.2.4 | ScalarspsDisplayString | read-write | mandatory | Setting this object changes the contents of the display. |
| 1.3.6.1.4.1.868.2.1.2.2.5 | TablespsRptrGroupTable | not-accessible | mandatory | Table of descriptive and status information about the repeater groups (Units). |
| 1.3.6.1.4.1.868.2.1.2.2.5.1 | RowspsRptrGroupEntry | not-accessible | mandatory | An entry in the table, containing information about a single repeater group. |
| 1.3.6.1.4.1.868.2.1.2.2.5.1.1 | ColumnspsRptrGroupIndex | read-only | mandatory | This object identifies the group containing the port for which this entry contains information. The group identified by a particular value of this index is the… |
| 1.3.6.1.4.1.868.2.1.2.2.5.1.2 | ColumnspsRptrGroupUnitId | read-only | mandatory | A unique string which identifies this unit. |
| 1.3.6.1.4.1.868.2.1.2.2.5.1.3 | ColumnspsRptrGroupInternalPowerSupply | read-only | mandatory | This object indicates the status of the internal power supply. A value of present(1) indicates the power supply is present and able to provide power. A value o… |
| 1.3.6.1.4.1.868.2.1.2.2.6 | TablespsRptrPortTable | not-accessible | mandatory | Table of descriptive and status information about the ports. |
| 1.3.6.1.4.1.868.2.1.2.2.6.1 | RowspsRptrPortEntry | not-accessible | mandatory | An entry in the table, containing information about a single port. |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.1 | ColumnspsRptrPortGroupIndex | read-only | mandatory | This object identifies the group containing the port for which this entry contains information. The group identified by a particular value of this index is the… |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.2 | ColumnspsRptrPortIndex | read-only | mandatory | This object identifies the port within the group for which this entry contains information. The port identified by a particular value of this index is the same… |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.3 | ColumnspsRptrPortSegment | read-write | mandatory | The segment number to which this port belongs. This value is never greater than spsMaxSegment. |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.4 | ColumnspsRptrPortSrcAddr | read-write | mandatory | When spsRptrPortEavesdropping or spsRptrPortIntrusion are enabled this object contains the authorized source address, otherwise this object contains the source… |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.5 | ColumnspsRptrPortEavesdropping | read-write | mandatory | Eavesdropping protection safeguards the network from promiscuous mode stations receiving intelligible data from the network. Setting this object to enabled(1) … |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.6 | ColumnspsRptrPortIntrusion | read-write | mandatory | Automatic intrusion protection prevents unauthorized users from gaining access to the network. Conceptually, the source address field of the received packet is… |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.7 | ColumnspsRptrPortCollisionLimit | read-write | mandatory | Selects the consecutive collision count that will cause port partitioning. Valid values are 31, 63, 127, and 255. |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.8 | ColumnspsRptrPortEnableIntruderDetectTrap | read-write | mandatory | Indicates whether the SNMP agent process is permitted to generate intruderDetection traps. |
| 1.3.6.1.4.1.868.2.1.2.2.6.1.9 | ColumnspsRptrPortDisableIntruder | write-only | mandatory | Indicates whether the port is disabled when an intruder is detected. Disabling a port in this manner is the same as setting the rptrPortAdminStatus object for … |
| 1.3.6.1.4.1.868.2.1.2.2.7 | TablespsSerialPortTable | not-accessible | mandatory | The table of RS-232 serial ports. Table only contains information not found in RFC-1316 and RFC-1317 Definitions of Managed Objects for RS-232-like Hardware De… |
| 1.3.6.1.4.1.868.2.1.2.2.7.1 | RowspsSerialPortEntry | not-accessible | mandatory | Table entry for a specific RS-232 serial port. |
| 1.3.6.1.4.1.868.2.1.2.2.7.1.1 | ColumnspsSerialPortIndex | read-only | mandatory | A unique value for each port. |
| 1.3.6.1.4.1.868.2.1.2.2.7.1.2 | ColumnspsSerialPortModemControl | read-only | mandatory | Setting this object to enabled(1) enables the monitoring and control of modem control lines by the serial port. Setting this object to disabled(2) disables the… |
| 1.3.6.1.4.1.868.2.1.2.2.8 | TablespsMonitorSegmentTable | not-accessible | mandatory | Table of performance and error statistics for the segments. |
| 1.3.6.1.4.1.868.2.1.2.2.8.1 | RowspsMonitorSegmentEntry | not-accessible | mandatory | An entry in the table, containing total performance and error statistics for a single segment. Regular retrieval of the information in this table provides a me… |
| 1.3.6.1.4.1.868.2.1.2.2.8.1.1 | ColumnspsMonitorSegmentIndex | read-only | mandatory | This object identifies the group within the repeater for which this entry contains information. |
| 1.3.6.1.4.1.868.2.1.2.2.8.1.2 | ColumnspsMonitorSegmentTotalFrames | read-only | mandatory | The total number of frames of valid frame length that have been received on the ports in this group and for which the FCSError and CollisionEvent signals were … |
| 1.3.6.1.4.1.868.2.1.2.2.8.1.3 | ColumnspsMonitorSegmentTotalOctets | read-only | mandatory | The total number of octets contained in the valid frames that have been received on the ports in this segment. This counter is the summation of the values of t… |
| 1.3.6.1.4.1.868.2.1.2.2.8.1.4 | ColumnspsMonitorSegmentTotalErrors | read-only | mandatory | The total number of errors which have occurred on all of the ports in this segment. This counter is the summation of the values of the rptrMonitorPortTotalErro… |
| 1.3.6.1.4.1.868.2.2 | Nodering | |||
| 1.3.6.1.4.1.868.2.2.1 | NodetnStackTR | |||
| 1.3.6.1.4.1.868.2.2.1.1 | NodetnTRCommon | |||
| 1.3.6.1.4.1.868.2.2.1.1.1 | ScalartnTRComHwReset | read-write | mandatory | Perform a hardware reset. |
| 1.3.6.1.4.1.868.2.2.1.1.2 | ScalartnTRComMgmtHwRev | read-only | mandatory | The management h/w board revision. |
| 1.3.6.1.4.1.868.2.2.1.1.3 | ScalartnTRComDiagSwRev | read-only | mandatory | The diagnostic s/w code revision. |
| 1.3.6.1.4.1.868.2.2.1.1.4 | ScalartnTRComMgmtSwRev | read-only | mandatory | The downloadable management s/w code revision. |
| 1.3.6.1.4.1.868.2.2.1.1.5 | ScalartnTRComIpAddr | read-write | mandatory | The IP address to which this entry's addressing information pertains. |
| 1.3.6.1.4.1.868.2.2.1.1.6 | ScalartnTRComNetMask | read-write | mandatory | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits … |
| 1.3.6.1.4.1.868.2.2.1.1.7 | ScalartnTRComIfaceCapacity | read-only | mandatory | The total number of interfaces found in the stack. |
| 1.3.6.1.4.1.868.2.2.1.2 | NodetnTRVer1 | |||
| 1.3.6.1.4.1.868.2.2.1.2.1 | ScalartnTRV1Commands | read-write | mandatory | When this object is set to the value of open(2), the station should go into the open state. The progress and success of the open is given by the values of the … |
| 1.3.6.1.4.1.868.2.2.1.2.2 | ScalartnTRV1RingStatus | read-only | mandatory | The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station has successfully been added to t… |
| 1.3.6.1.4.1.868.2.2.1.2.3 | ScalartnTRV1RingState | read-only | mandatory | The current interface state with respect to entering or leaving the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.4 | ScalartnTRV1RingOpenStatus | read-only | mandatory | This object indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.5 | ScalartnTRV1RingSpeed | read-write | mandatory | The ring's bandwidth. |
| 1.3.6.1.4.1.868.2.2.1.2.6 | ScalartnTRV1UpStream | read-only | mandatory | The MAC-address of the up stream neighbor station in the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.7 | ScalartnTRV1ActMonParticipate | read-write | mandatory | If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. … |
| 1.3.6.1.4.1.868.2.2.1.2.8 | ScalartnTRV1Functional | read-write | mandatory | The bit mask of all Token Ring functional addresses for which this interface will accept frames. |
| 1.3.6.1.4.1.868.2.2.1.2.9 | ScalartnTRV1StatsLineErrors | read-only | mandatory | This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditio… |
| 1.3.6.1.4.1.868.2.2.1.2.10 | ScalartnTRV1StatsBurstErrors | read-only | mandatory | This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error). |
| 1.3.6.1.4.1.868.2.2.1.2.11 | ScalartnTRV1StatsACErrors | read-only | mandatory | This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is e… |
| 1.3.6.1.4.1.868.2.2.1.2.12 | ScalartnTRV1StatsAbortTransErrors | read-only | mandatory | This counter is incremented when a station transmits an abort delimiter while transmitting. |
| 1.3.6.1.4.1.868.2.2.1.2.13 | ScalartnTRV1StatsInternalErrors | read-only | mandatory | This counter is incremented when a station recognizes an internal error. |
| 1.3.6.1.4.1.868.2.2.1.2.14 | ScalartnTRV1StatsLostFrameErrors | read-only | mandatory | This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip … |
| 1.3.6.1.4.1.868.2.2.1.2.15 | ScalartnTRV1StatsReceiveCongestions | read-only | mandatory | This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station … |
| 1.3.6.1.4.1.868.2.2.1.2.16 | ScalartnTRV1StatsFrameCopiedErrors | read-only | mandatory | This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a … |
| 1.3.6.1.4.1.868.2.2.1.2.17 | ScalartnTRV1StatsTokenErrors | read-only | mandatory | This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted. |
| 1.3.6.1.4.1.868.2.2.1.2.18 | ScalartnTRV1StatsSoftErrors | read-only | mandatory | The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Sof… |
| 1.3.6.1.4.1.868.2.2.1.2.19 | ScalartnTRV1StatsHardErrors | read-only | mandatory | The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or… |
| 1.3.6.1.4.1.868.2.2.1.2.20 | ScalartnTRV1StatsSignalLoss | read-only | mandatory | The number of times this interface has detected the loss of signal condition from the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.21 | ScalartnTRV1StatsTransmitBeacons | read-only | mandatory | The number of times this interface has transmitted a beacon frame. |
| 1.3.6.1.4.1.868.2.2.1.2.22 | ScalartnTRV1StatsRecoverys | read-only | mandatory | The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This counter signifies the number of time… |
| 1.3.6.1.4.1.868.2.2.1.2.23 | ScalartnTRV1StatsLobeWires | read-only | mandatory | The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and dot5RingState will signify this c… |
| 1.3.6.1.4.1.868.2.2.1.2.24 | ScalartnTRV1StatsRemoves | read-only | mandatory | The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state an… |
| 1.3.6.1.4.1.868.2.2.1.2.25 | ScalartnTRV1StatsSingles | read-only | mandatory | The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if th… |
| 1.3.6.1.4.1.868.2.2.1.2.26 | ScalartnTRV1StatsFreqErrors | read-only | optional | The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by more than that specified by the… |
| 1.3.6.1.4.1.868.2.2.1.2.27 | ScalartnTRV1TimerReturnRepeat | read-only | mandatory | The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be greater than the maximum ring l… |
| 1.3.6.1.4.1.868.2.2.1.2.28 | ScalartnTRV1TimerHolding | read-only | mandatory | Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds. Implementers are encouraged to provide… |
| 1.3.6.1.4.1.868.2.2.1.2.29 | ScalartnTRV1TimerQueuePDU | read-only | mandatory | The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0, in units of 100 micro-seconds.… |
| 1.3.6.1.4.1.868.2.2.1.2.30 | ScalartnTRV1TimerValidTransmit | read-only | mandatory | The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds. Implementers are encouraged to provi… |
| 1.3.6.1.4.1.868.2.2.1.2.31 | ScalartnTRV1TimerNoToken | read-only | mandatory | The time-out value used to recover from various-related error situations [9]. If N is the maximum number of stations on the ring, the value of this timer is no… |
| 1.3.6.1.4.1.868.2.2.1.2.32 | ScalartnTRV1TimerActiveMon | read-only | mandatory | The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-seconds. Implementors are encour… |
| 1.3.6.1.4.1.868.2.2.1.2.33 | ScalartnTRV1TimerStandbyMon | read-only | mandatory | The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuous stream of tokens, in units of… |
| 1.3.6.1.4.1.868.2.2.1.2.34 | ScalartnTRV1TimerErrorReport | read-only | mandatory | The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds. Implem… |
| 1.3.6.1.4.1.868.2.2.1.2.35 | ScalartnTRV1TimerBeaconTransmit | read-only | mandatory | The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering the Bypass state, in units of 10… |
| 1.3.6.1.4.1.868.2.2.1.2.36 | ScalartnTRV1TimerBeaconReceive | read-only | mandatory | The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering the Bypass state, in units of 1… |
| 1.3.6.1.4.1.868.2.2.1.3 | NodetnTRVer2 | |||
| 1.3.6.1.4.1.868.2.3 | Nodebridge | |||
| 1.3.6.1.4.1.868.2.3.1 | Nodesfbrm10x100 | |||
| 1.3.6.1.4.1.868.2.3.1.1 | NodesfbrmSystem | |||
| 1.3.6.1.4.1.868.2.3.1.1.1 | Tablesfbrm100SystemTable | not-accessible | mandatory | System Information and Configuration table for the xFBRM/xBFFG 802.3ah Managed device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1 | Rowsfbrm100SystemEntry | not-accessible | mandatory | Status and configuration entries for a xFBRM/xBFFG device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.1 | Columnsfbrm100SysLocPortIndex | read-only | mandatory | The local port index of the port to which the peer is connected. The local device has an index of 0. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.2 | Columnsfbrm100SysSecIndex | read-only | mandatory | Secondary index for the table. It is always 1. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.3 | Columnsfbrm100SysGrpString | read-write | mandatory | Group membership string. See http://www.transition.com/pshelp/configmgmt1.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.4 | Columnsfbrm100SysMRevision | read-only | mandatory | The marketing revision of this device. See http://www.transition.com/pshelp/mrevision.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.5 | Columnsfbrm100SysCfgMatch | read-write | mandatory | See http://www.transition.com/pshelp/configmgmt1.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.6 | Columnsfbrm100SysBootLoaderRevision | read-only | mandatory | The bootloader revision level for this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.7 | Columnsfbrm100SysFirmwareRevision | read-only | mandatory | The firmware revision level for this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.8 | Columnsfbrm100SysSerialNumber | read-only | mandatory | The serial number of this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.9 | Columnsfbrm100SysBIAddress | read-only | mandatory | The serial number (BIA) of the cabinet in which the device is installed. If it is a stand-alone this is zero. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.10 | Columnsfbrm100SysSlotIndex | read-only | mandatory | The Slot number if installed in a chassis. Zero if stand-alone. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.11 | Columnsfbrm100SysNumPorts | read-only | mandatory | The Number of ports on this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.12 | Columnsfbrm100SysMACAddress | read-only | mandatory | The MAC address used in MGMT frames and IP Packets. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.13 | Columnsfbrm100SystemReset | read-write | mandatory | Set this to reset(1) to cause the system to reboot. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.14 | Columnsfbrm100SysIPaddress | read-write | mandatory | The IPV4 address of the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.15 | Columnsfbrm100SysSubnetMask | read-write | mandatory | The subnet mask associated with the IP address of the device. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits … |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.16 | Columnsfbrm100SysDefGateway | read-write | mandatory | The default gateway for the device |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.17 | Columnsfbrm100SysSNMPTrapMgr | read-write | mandatory | The IPV4 address of the SNMP trap manager. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.18 | Columnsfbrm100SysRadiusAuth | read-write | mandatory | RADIUS authentication can be enabled or disabled using this variable. RADIUS Authentication is used for management access only. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.19 | Columnsfbrm100SysRadiusServerAddr | read-write | mandatory | The IPV4 address of the Radius Server. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.20 | Columnsfbrm100SysRadiusSecret | read-write | mandatory | The shared secret between the device and RADIUS server. A read returns 'xxx' for security. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.21 | Columnsfbrm100SysRadiusRetry | read-write | mandatory | The number of times the device would try to contact the RADIUS server, when there is any communication problem. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.22 | Columnsfbrm100SysRadiusTimeout | read-write | mandatory | The number of seconds the device would wait for the server response before it times out. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.23 | Columnsfbrm100SysDHCPEnable | read-write | mandatory | Enable/Disable DHCP. A reset of the system is needed. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.24 | Columnsfbrm100SysSerialAccess | read-write | mandatory | Enable/Disable access to USB Port. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.25 | Columnsfbrm100SysTLPT | read-write | mandatory | Enable/disable Transparent Link Pass through. If the Peer's remote link goes down, the link down is passed on to the other end while the OAM channel is still a… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.26 | Columnsfbrm100SysTFTPServerAddr | read-write | mandatory | The IPV4 address of the TFTP Server. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.27 | Columnsfbrm100SysTFTPfilename | read-write | mandatory | The Firmware file to be downloaded from the TFTP Server for upgrading. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.28 | Columnsfbrm100SysTFTPCmd | read-write | mandatory | To initiate a TFTP upgrading, set the value to perform(1), the systems resets and the bootloader is invoked to perform the upgrade. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.29 | Columnsfbrm100SysTFTPServerIgnore | read-write | mandatory | In some configuration, when the device uses DHCP to get its IP address, it also receives the tftpserver address for upgrading. When this variable is enabled th… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.30 | Columnsfbrm100SysMgmtVlanId | read-only | mandatory | VLAN Id for the management frames. This is valid only when vlan is enabled. This creates a secure channel for all management traffic. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.31 | Columnsfbrm100SysSNMPAccess | read-write | mandatory | The SNMP access to the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.32 | Columnsfbrm100SysIPAccess | read-write | mandatory | IP management access to the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.33 | Columnsfbrm100SysLastGaspPdu | read-write | mandatory | This mib variable is used to choose the type of PDU to be generated on the last gasp event. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.34 | Columnsfbrm100SysLastGaspPort | read-write | mandatory | When there are multiple OAM enabled ports, this variable decides which port to send the Dying gasp OAM PDU. The default is Port 2. This variable is valid only … |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.35 | Columnsfbrm100SysLocalLPT | read-write | mandatory | When the monitored port (sfbrm100SysLPTPort)link goes down, the other port is brought down when this is enabled. This is also named as Selective Link Pass Thro… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.36 | Columnsfbrm100SysLPTPort | read-write | mandatory | This determines the port, on which the Transparent Link pass through and the Selective/local Link pass through will be active. Any link change on this port act… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.37 | Columnsfbrm100SysAutoUpgrade | read-write | mandatory | When enabled, auto upgrade of this device can be done by its peer. By default this is 'enabled(1)'. When disabled, the peer should do a Force upgrade in order … |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.38 | Columnsfbrm100SysFormFactorSlot | read-only | mandatory | This read-only variable gives the number of slots in a chassis this unit occupies if its a chassis card. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.39 | Columnsfbrm100SysFormFactorPort | read-only | mandatory | This read-only variables gives type of ports present on this board. The values and description for each board : 1 - xFBRM 10/100BaseT to 100BaseFx 2 - xFBRM 10… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.40 | Columnsfbrm100SysOAMPort | read-write | mandatory | When only one OAM session is allowed, this determines the port that will be used for sending and receiving OAM messages. This also restricts the number of mana… |
| 1.3.6.1.4.1.868.2.3.1.2 | NodesfbrmSwitch | |||
| 1.3.6.1.4.1.868.2.3.1.2.1 | Tablesfbrm100SwTable | not-accessible | mandatory | Switch Status and configuration table |
| 1.3.6.1.4.1.868.2.3.1.2.1.1 | Rowsfbrm100SwEntry | not-accessible | mandatory | Status and configuration entries for switch setting. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.1 | Columnsfbrm100SwPortIndex | read-only | mandatory | The Local Port Index of the local port to which the peer is connected. The local device has the port index of 0. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.2 | Columnsfbrm100SwSecIndex | read-only | mandatory | Secondary index for the table. It is always 1. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.3 | Columnsfbrm100SwATUAgeTimeout | read-write | mandatory | The ATU ageing time in seconds. This indicates the time that each ATU entry remains valid in the database before being purged. The minimum aging time is 15 sec… |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.4 | Columnsfbrm100SwIngressMonPort | read-write | mandatory | The Ingress monitor port. Frames that are targeted towards an Ingress monitor port go out this port. Not-applicable for a 2-Port device. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.5 | Columnsfbrm100SwEgressMonPort | read-write | mandatory | The egress monitor port. Frames that are targeted towards an Egress monitor port go out this port. Not-applicable for a 2-Port device. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.6 | Columnsfbrm100SwFactoryDefaults | read-write | mandatory | Reset the switch to factory default settings. A read always returns a notApplicable(2) value. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.7 | Columnsfbrm100SwResetCounters | read-write | mandatory | Resets all port counters. A read always returns a notApplicable(2) value. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.8 | Columnsfbrm100SwHistMode | read-write | mandatory | The port histogram counters can be set to : cntRx (1) - count Rx frames only. cntTx (2) - count Tx frames only cntRxTx (3) - count Rx and Tx frames. This affec… |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.9 | Columnsfbrm100SwIEEEPriRemap0 | read-write | mandatory | All Frames with priority 0 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.10 | Columnsfbrm100SwIEEEPriRemap1 | read-write | mandatory | All Frames with priority 1 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.11 | Columnsfbrm100SwIEEEPriRemap2 | read-write | mandatory | All Frames with priority 2 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.12 | Columnsfbrm100SwIEEEPriRemap3 | read-write | mandatory | All Frames with priority 3 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.13 | Columnsfbrm100SwIEEEPriRemap4 | read-write | mandatory | All Frames with priority 4 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.14 | Columnsfbrm100SwIEEEPriRemap5 | read-write | mandatory | All Frames with priority 5 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.15 | Columnsfbrm100SwIEEEPriRemap6 | read-write | mandatory | All Frames with priority 6 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.16 | Columnsfbrm100SwIEEEPriRemap7 | read-write | mandatory | All Frames with priority 7 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.17 | Columnsfbrm100SwFlushFdb | read-write | mandatory | Flushes all static entries in the forwarding database. When set to flushAll(1), all the entries in the database are purged. when set to flushNonStatic(2), all … |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.18 | Columnsfbrm100SwFlushVlandb | read-write | mandatory | Flushes all VLAN entries in the database. When set to flushAll(1), all VLAN entries in the database are purged, and VLAN is disabled automatically. A read alwa… |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.19 | Columnsfbrm100SwUseDoubleTagData | read-write | mandatory | When Double tagging is enabled on any of the ports, this mib variable decides if the tag that is removed from Ingress frames should be used or ignored when mak… |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.20 | Columnsfbrm100SwFiberRedundancy | read-write | mandatory | This feature is applicable in the xFBRM/xBFFG series which have 2 fiber ports. When set to enabled, the primary and backup fiber ports are assumed to be connec… |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.21 | Columnsfbrm100SwFiberRedundRevert | read-write | mandatory | This mib variable is applicable only if 'sfbrm100SwFiberRedundancy' is enabled. When there is a failure in the primary and secondary fiber takes over, this det… |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.22 | Columnsfbrm100SwFbrRedundActivePort | read-write | mandatory | This mib variable is applicable only if 'sfbrm100SwFiberRedundancy' is enabled. This indicates the current active port that is operational as the primary link. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.23 | Columnsfbrm100SwSupressVlanViolations | read-write | mandatory | This supresses all VLAN database violations and the traps caused by these events. |
| 1.3.6.1.4.1.868.2.3.1.2.1.1.24 | Columnsfbrm100SwSupressMACViolations | read-write | mandatory | This supresses all MAC database violations and the traps caused by these events. |
| 1.3.6.1.4.1.868.2.3.1.2.2 | Tablesfbrm100SwIPPrioTable | not-accessible | mandatory | IP Traffic class table. |
| 1.3.6.1.4.1.868.2.3.1.2.2.1 | Rowsfbrm100SwIPPrioEntry | not-accessible | mandatory | Each entry represents the remapped value for each traffic class. |
| 1.3.6.1.4.1.868.2.3.1.2.2.1.1 | Columnsfbrm100SwIPPrioPortIndex | read-only | mandatory | The Local port to which the device is connected. The local device has the port index as zero. |
| 1.3.6.1.4.1.868.2.3.1.2.2.1.2 | Columnsfbrm100SwIPPrioIndex | read-only | mandatory | The IP traffic class remap table index. |
| 1.3.6.1.4.1.868.2.3.1.2.2.1.3 | Columnsfbrm100SwIPPrioTC | read-only | mandatory | The IP traffic class value. |
| 1.3.6.1.4.1.868.2.3.1.2.2.1.4 | Columnsfbrm100SwIPPrioRemap | read-write | mandatory | The IP traffic class defined by sfbrm100SwIPPrioTC, is given the priority value set in this variable. |
| 1.3.6.1.4.1.868.2.3.1.3 | NodesfbrmPort | |||
| 1.3.6.1.4.1.868.2.3.1.3.1 | Tablesfbrm100PortTable | not-accessible | mandatory | Port attributes status and configuration. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1 | Rowsfbrm100PortEntry | not-accessible | mandatory | Status and configuration entries for a each port on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.1 | Columnsfbrm100PortLocIndex | read-only | mandatory | Uniquely indentifies each port on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.2 | Columnsfbrm100PortRmtIndex | read-only | mandatory | Uniquely indentifies each port on the peer device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.3 | Columnsfbrm100PortGrpString | read-write | mandatory | Description string for each port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.4 | Columnsfbrm100PortConnType | read-only | mandatory | The actual physical connector on the port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.5 | Columnsfbrm100PortOAMState | read-write | mandatory | This object is used to provision the default administrative enable/disable of OAM on this interface. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.6 | Columnsfbrm100PortOAMModeCtrl | read-write | mandatory | This object can be used to provision the OAM mode for this interface. In auto(1) mode , the interface is set to active/passive depending on if the board is in … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.7 | Columnsfbrm100PortRmtLoopback | read-write | mandatory | Initiates remote loopback, if supported by remote peer. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.8 | Columnsfbrm100PortIgnoreLoopback | read-write | mandatory | If enabled, the device ignores any loopback requests. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.9 | Columnsfbrm100PortAdvPause | read-write | mandatory | Specifies the Pause frame advertisement capability. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.10 | Columnsfbrm100PortAdv1000FDX | read-write | mandatory | This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, full duplex. This is ignored when autonegotiation i… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.11 | Columnsfbrm100PortAdv1000HDX | read-write | mandatory | This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, half duplex. This is ignored when autonegotiation i… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.12 | Columnsfbrm100PortAdv100FDX | read-write | mandatory | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, full duplex. This is ignored when autonegotiation is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.13 | Columnsfbrm100PortAdv100HDX | read-write | mandatory | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is ignored when autonegotiation is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.14 | Columnsfbrm100PortAdv10FDX | read-write | mandatory | This configuration setting controls whether or not this port advertises willingness to connect at 10Mbps, full duplex. This is ignored when autonegotiation is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.15 | Columnsfbrm100PortAdv10HDX | read-write | mandatory | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is ignored when autonegotiation is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.16 | Columnsfbrm100PortAutoneg | read-write | mandatory | Enable/Disable autonegotiation on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.17 | Columnsfbrm100PortFDuplex | read-write | mandatory | This is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. This is valid only when autonegotiation… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.18 | Columnsfbrm100PortFSpeed | read-write | mandatory | This is a configuration setting that controls the speed; This is valid only when autonegotiation is disabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.19 | Columnsfbrm100PortLpPauseAbility | read-only | mandatory | Link Partner's pause capability. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.20 | Columnsfbrm100PortLpAutonegAbility | read-write | mandatory | The autonegotiation advertisement mode can be set using the options of this variable. spdAutoDupAuto(1) - Advertise all speed and duplex supported. spd1000DupA… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.21 | Columnsfbrm100PortLinkState | read-only | mandatory | Link status on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.22 | Columnsfbrm100PortAutonegState | read-only | mandatory | The autonegotiation state or if autonegotiation is disabled it returns resolved(1). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.23 | Columnsfbrm100PortDuplex | read-only | mandatory | The port's duplex value when autonegotiation is resolved. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.24 | Columnsfbrm100PortSpeed | read-only | mandatory | The port's duplex value when autonegotiation is resolved |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.25 | Columnsfbrm100PortFEFI | read-write | mandatory | Enabled/Disable Far-end Fault detection. Read-only value notApplicable is returned for unsupported Ethernet PHY's. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.26 | Columnsfbrm100PortAutocross | read-write | mandatory | This is applicable for supporting PHY's. If set to mdi(1) the transmit happens on pair 1 & 2 and receive on 3 & 4. If set to mdiX(2) the transmit happens on 3 … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.27 | Columnsfbrm100PortLock | read-write | mandatory | When enabled, it disables the automatic learning of source addresses on this port and drops frames where the SA does not exist in the ATU, and originates a ATU… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.28 | Columnsfbrm100PortIgnoreWrongData | read-write | mandatory | Ignores interrupts caused by reception of frames whose source address is not assigned to this port. When disabled(2), generates a SNMP trap every time a frame … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.29 | Columnsfbrm100PortIGMPSnoop | read-write | mandatory | When enabled all IGMP frames are directed to the CPU overriding the Destination address. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.30 | Columnsfbrm100PortDoubleTagging | read-write | mandatory | When set to enabled, the frames which have 802.3ac tag with IEEE standard ether-type of 0x8100 are examined for tags. On Ingress frames : All untagged frames r… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.31 | Columnsfbrm100PortUseIPTC | read-write | mandatory | When enabled, IP priority fields are used for Traffic class of priority data. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.32 | Columnsfbrm100PortUseTagTC | read-write | mandatory | When enabled, the IEEE 802.1p fields are used for traffic class of priority data if the frame is IEEE 802.1ac tagged. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.33 | Columnsfbrm100PortUseBothTC | read-write | mandatory | When a frame has both IP priority fields and IEEE 802.1ac tags and both sfbrm100PortUseIPTC and sfbrm100PortUseTagTC are enabled then this mib variable is used… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.34 | Columnsfbrm100PortVLANTunnel | read-write | mandatory | For all unicast and multicast frames with destination address defined as 'static' in the address database port-based VLAN masking, 802.1Q VLAN membership maski… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.35 | Columnsfbrm100PortFwdUnknown | read-write | mandatory | When enabled, all unicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allow this frame to egress). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.36 | Columnsfbrm100PortDefForward | read-write | mandatory | When enabled, all multicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allow this frame to egress). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.37 | Columnsfbrm100PortAdminState | read-write | mandatory | Set port state administratively up or down. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.38 | Columnsfbrm100PortVTUPriOverride | read-write | mandatory | When disabled, normal switch operation is done. When enabled, VTU Priority override occurs. i.e The determined VID priority takes precedence over all other pri… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.39 | Columnsfbrm100PortSAPriOverride | read-write | mandatory | When enabled, Source address decides the priority as per the address database entry rules. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.40 | Columnsfbrm100PortDAPriOverride | read-write | mandatory | When enabled, Destination address decides the priority as per the address database entry rules. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.41 | Columnsfbrm100PortVLANStatus | read-write | mandatory | 802.1Q VLAN setting : vlanDisabled - 802.1Q is disabled. fallback - The frame is not discarded if the VID is not in the VLAN Db. check - The VID must be in the… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.42 | Columnsfbrm100PortDiscardTagged | read-write | mandatory | All ingress tagged frames are discarded if enabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.43 | Columnsfbrm100PortDiscardUntagged | read-write | mandatory | All untagged ingress frames are discarded if enabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.44 | Columnsfbrm100PortEgressMonitor | read-write | mandatory | Any frame that egress this port is also sent to the egress monitor destination port. Not applicable for 2-port device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.45 | Columnsfbrm100PortIngressMonitor | read-write | mandatory | Any frame that ingress this port is also sent to the ingress monitor destination port. Not applicable for 2-port device |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.46 | Columnsfbrm100PortPri3IngressRateCtrl | read-write | mandatory | Ingress rate limit for Priority 3 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.47 | Columnsfbrm100PortPri2IngressRateCtrl | read-write | mandatory | Ingress rate limit for Priority 2 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.48 | Columnsfbrm100PortPri1IngressRateCtrl | read-write | mandatory | Ingress rate limit for Priority 1 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.49 | Columnsfbrm100PortPri0IngressRate | read-write | mandatory | Ingress rate for Priority 0 frames in bits per second, but not faster than port speed. Priority 0 frames are discarded after the ingress rate selected is reach… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.50 | Columnsfbrm100PortIngressLimitMode | read-write | mandatory | Ingress Limit mode. all(1) - Limits and counts all frames bCastMCastFloodedUCast(2) - Limits and counts all broadcast, multicast and flooded unicast frames. bC… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.51 | Columnsfbrm100PortEgressRate | read-write | mandatory | Egress priority rate in bits per seconds. This affects the port's effective transmission rate. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.52 | Columnsfbrm100PortDefaultPriority | read-write | mandatory | The default priority of the frame if its not IEEE tagged or not IP frames or no other priority overides are active for this frame. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.53 | Columnsfbrm100PortForceDefVLANId | read-write | mandatory | Force to use the sfbrm100PortDefaultVLANId when 802.1Q is enabled on this port. The frames actual VLAN id is replaced with the default VLAN Id. Has no effect w… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.54 | Columnsfbrm100PortDefaultVLANId | read-write | mandatory | The default VLAN Id of the port. All untagged frames that are to exit tagged will use the VID of the ingress port on exit. This VID is also used on all frames … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.55 | Columnsfbrm100PortBasedVLANTbl | read-write | mandatory | Each bit represents ports on the switch. These bits restrict where this port can send frames to, setting the bits to zero will disable this port's ability to e… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.56 | Columnsfbrm100PortIEEEPriRemap0 | read-write | mandatory | All Frames with priority 0 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.57 | Columnsfbrm100PortIEEEPriRemap1 | read-write | mandatory | All Frames with priority 1 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.58 | Columnsfbrm100PortIEEEPriRemap2 | read-write | mandatory | All Frames with priority 2 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.59 | Columnsfbrm100PortIEEEPriRemap3 | read-write | mandatory | All Frames with priority 3 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.60 | Columnsfbrm100PortIEEEPriRemap4 | read-write | mandatory | All Frames with priority 4 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.61 | Columnsfbrm100PortIEEEPriRemap5 | read-write | mandatory | All Frames with priority 5 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.62 | Columnsfbrm100PortIEEEPriRemap6 | read-write | mandatory | All Frames with priority 6 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.63 | Columnsfbrm100PortIEEEPriRemap7 | read-write | mandatory | All Frames with priority 7 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.64 | Columnsfbrm100PortVCTest | read-write | mandatory | The virtual cable test can be done using this variable set to perform(1), otherwise the Read-only value notApplicable(2) will be returned. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.65 | Columnsfbrm100PortVCTxMDI0Status | read-only | mandatory | The test status of the Tx pair or MDI[0](Gigabit port) depending on port type. normal(1) - Test was successful, cable is normal (no short or open in cable) imp… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.66 | Columnsfbrm100PortTxMDI0Dist | read-only | mandatory | The cable distance of the Tx pair or MDI[0](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this gives the d… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.67 | Columnsfbrm100PortVCRxMDI1Status | read-only | mandatory | The test status of the Rx or MDI[1](Gigabit port) depending on port type. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanc… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.68 | Columnsfbrm100PortRxMDI1Dist | read-only | mandatory | The cable distance of the Rx pair or MDI[1](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this gives the d… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.69 | Columnsfbrm100PortVCMDI2Status | read-only | mandatory | The test status of the MDI[2](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanceMismatch(2)- Te… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.70 | Columnsfbrm100PortMDI2Dist | read-only | mandatory | The cable distance of the MDI[2](if Gigabit port else notApplicable(6)) from the test port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.71 | Columnsfbrm100PortVCMDI3Status | read-only | mandatory | The test status of the MDI[3](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanceMismatch(2)- Te… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.72 | Columnsfbrm100PortMDI3Dist | read-only | mandatory | The cable distance of the MDI[3](if Gigabit port else notApplicable(6)) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, th… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.73 | Columnsfbrm100PortResetCounters | read-write | mandatory | Resets all the port counters for this port. A read returns read-only value donothing(2). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.74 | Columnsfbrm100PortIPTrafficAccess | read-write | mandatory | Allow/block IP management traffic on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.75 | Columnsfbrm100PortResetOAMCounters | read-write | mandatory | Resets all OAM counters for this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.76 | Columnsfbrm100PortForceAutoUpgrade | read-write | mandatory | Force Automatic firmware upgrade on this peer, when the peer has its auto upgrade turned off. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.77 | Columnsfbrm100PortModeType | read-write | mandatory | The Interface mode. The capabilities of the interface. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.78 | Columnsfbrm100PortOAMMode | read-write | mandatory | The OAM mode for this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.79 | Columnsfbrm100PortPhyNumber | read-only | mandatory | This gives the physical port number on the hardware switch. This is useful in computing the port based VLAN setting for this port. The bit position in the port… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.80 | Columnsfbrm100PortIngressRateLimit2 | read-write | mandatory | Ingress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if the ingress rate selected is reached or exceeded. Device… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.81 | Columnsfbrm100PortEgressRateLimit2 | read-write | mandatory | Egress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if over the limit. Devices which support this mib variable d… |
| 1.3.6.1.4.1.868.2.3.1.3.2 | Tablesfbrm100PortStatsTable | not-accessible | mandatory | Port Statistics table. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1 | Rowsfbrm100PortStatsEntry | not-accessible | mandatory | Statistics for a single port. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.1 | Columnsfbrm100PortLocStatsIndex | read-only | mandatory | The port index of the local port as defined by sfbrm100PortLocIndex. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.2 | Columnsfbrm100PortRmtStatsIndex | read-only | mandatory | The remote port index of the remote peer as defined by sfbrm100PortRmtIndex. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.3 | Columnsfbrm100PortInGoodOctetsLo | read-only | mandatory | The lower 32-bits of the received good octets counter. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.4 | Columnsfbrm100PortInGoodOctetsHi | read-only | mandatory | The upper 32-bits of the received good octets counter. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.5 | Columnsfbrm100PortInBadOctets | read-only | mandatory | The sum of all octets in bad Ethernet frames. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.6 | Columnsfbrm100PortInUnicasts | read-only | mandatory | The number of good unicast frames. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.7 | Columnsfbrm100PortInBroadcasts | read-only | mandatory | The number of good broadcast frames. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.8 | Columnsfbrm100PortInMulticasts | read-only | mandatory | The number of good multicast frames. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.9 | Columnsfbrm100PortInPause | read-only | mandatory | The number of good Pause flow control frames. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.10 | Columnsfbrm100PortInUndersize | read-only | mandatory | The number of frames received with a length of less than 64 octets with a valid FCS. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.11 | Columnsfbrm100PortInFragments | read-only | mandatory | The number of frames received with a length of less than 64 octets with an invalid FCS. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.12 | Columnsfbrm100PortInOversize | read-only | mandatory | The number of frames received with a length of more than maximum size octets with a valid FCS. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.13 | Columnsfbrm100PortInJabber | read-only | mandatory | The number of frames received with a length of more than maximum size octets with an invalid FCS. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.14 | Columnsfbrm100PortInRxErr | read-only | mandatory | The number of frames received with a RxErr signal from the Physical layer |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.15 | Columnsfbrm100PortInFCSErr | read-only | mandatory | The number of frames received with a CRC error not counted in sfbrm100PortInFragments, sfbrm100PortInJabber or sfbrm100PortInRxErr. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.16 | Columnsfbrm100PortIn64Octets | read-only | mandatory | The total number of frames received with a length of 64 octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm10… |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.17 | Columnsfbrm100PortIn65to127Octets | read-only | mandatory | The total number of frames received with a length between 65 and 127 octets, including errored frames. This is a histogram counter, dependent on the histogram … |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.18 | Columnsfbrm100PortIn128to255Octets | read-only | mandatory | The total number of frames received with a length between 128 and 255 octets, including errored frames. This is a histogram counter, dependent on the histogram… |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.19 | Columnsfbrm100PortIn256to511Octets | read-only | mandatory | The total number of frames received with a length between 256 and 511 octets, including errored frames. This is a histogram counter, dependent on the histogram… |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.20 | Columnsfbrm100PortIn512to1023Octets | read-only | mandatory | The total number of frames received with a length between 512 and 1023 octets, including errored frames. This is a histogram counter, dependent on the histogra… |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.21 | Columnsfbrm100PortIn1024toMaxOctets | read-only | mandatory | The total number of frames received with a length between 1024 and max size octets, including errored frames. This is a histogram counter, dependent on the his… |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.22 | Columnsfbrm100PortOutOctetsLo | read-only | mandatory | The lower 32-bit of the sum of all frames sent from this port. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.23 | Columnsfbrm100PortOutOctetsHi | read-only | mandatory | The upper 32-bit of the sum of all frames sent from this port. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.24 | Columnsfbrm100PortOutUnicasts | read-only | mandatory | The number of unicast frames transmitted. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.25 | Columnsfbrm100PortOutBroadcasts | read-only | mandatory | The number of broadcast frames transmitted. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.26 | Columnsfbrm100PortOutMulticasts | read-only | mandatory | The number of multicast frames transmitted. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.27 | Columnsfbrm100PortOutPause | read-only | mandatory | The number of Pause frames transmitted. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.28 | Columnsfbrm100PortOutDeferred | read-only | mandatory | The number of frames transmitted with a delay. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.29 | Columnsfbrm100PortOutCollisions | read-only | mandatory | The number of collisions during transmission not including single, multiple, excessive or late collisions. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.30 | Columnsfbrm100PortOutSingle | read-only | mandatory | The number of frames transmitted with exactly one collision. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.31 | Columnsfbrm100PortOutMultiple | read-only | mandatory | The number of frames transmitted with more than one collision. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.32 | Columnsfbrm100PortOutExcessive | read-only | mandatory | The number of frames dropped due to excessive collision. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.33 | Columnsfbrm100PortOutLate | read-only | mandatory | The number of times a collision is detected later than 512 bits-times into transmission of a frame. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.34 | Columnsfbrm100PortOutFCSErr | read-only | mandatory | The number of frames transmitted with invalid FCS. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.35 | Columnsfbrm100PortInDiscard | read-only | mandatory | The number of good frames that were discarded due to lack of resources. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.36 | Columnsfbrm100PortInFiltered | read-only | mandatory | The number of good frames filtered due to ingress switch policy. |
| 1.3.6.1.4.1.868.2.3.1.3.2.1.37 | Columnsfbrm100PortOutFiltered | read-only | mandatory | The number of good frames filtered due to egress switch policy. |
| 1.3.6.1.4.1.868.2.3.1.3.3 | Tablesfbrm100DMITable | not-accessible | mandatory | DMI ports on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1 | Rowsfbrm100DMIEntry | not-accessible | mandatory | Status of the DMI ports. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.1 | Columnsfbrm100DMILocPortIndex | read-only | mandatory | The port index of the DMI port as defined by sfbrm100PortLocIndex. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.2 | Columnsfbrm100DMIRmtPortIndex | read-only | mandatory | The port index of the DMI port as defined by sfbrm100PortRmtIndex. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.3 | Columnsfbrm100DMIRxPwrLvlPreset | read-write | mandatory | A preset level for Rx Power on the Fiber port, if the DMI read value falls below the preset value, an intrusion is detected, and a trap is generated. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.4 | Columnsfbrm100DMIConnType | read-only | mandatory | The DMI connector type indicates the external optical or electrical cable connector provided as the interface. From SFF 8472 Rev 9.5 Value Description of conne… |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.5 | Columnsfbrm100DMIBitRate | read-only | mandatory | Bitrate in units of 100Mbps. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.6 | Columnsfbrm100DMILenFor9x125umKM | read-only | mandatory | Specifies the link length that is supported by the transceiver while operating in single mode fiber. The value is in units of KM. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.7 | Columnsfbrm100DMILenFor9x125um100M | read-only | mandatory | Specifies the link length that is supported by the transceiver while operating in single mode fiber. The value is in units of 100m. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.8 | Columnsfbrm100DMILenFor50x125um10M | read-only | mandatory | Specifies the link length that is supported by the transceiver while operating in 50 micron multi mode fiber. The value is in units of 10m. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.9 | Columnsfbrm100DMILenFor625x125um10M | read-only | mandatory | Specifies the link length that is supported by the transceiver while operating in 62.5 micron multi mode fiber. The value is in units of 10m. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.10 | Columnsfbrm100DMILenForCopper | read-only | mandatory | Specifies the link length that is supported by the transceiver while operating in copper cable. The value is in units of meters. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.11 | Columnsfbrm100DMIId | read-only | mandatory | Specifies the physical device. The table below from SFF-8472 Rev 9.5 Standard gives description for the values. 00h Unknown or unspecified 01h GBIC 02h Module/… |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.12 | Columnsfbrm100DMILaserWavelength | read-only | mandatory | The Nominal transmitter output wavelength at room temperature. The units in nm |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.13 | Columnsfbrm100DMITemperature | read-only | mandatory | Temperature of fiber transceiver in tenths of degrees C. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.14 | Columnsfbrm100DMITempAlarm | read-only | mandatory | . |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.15 | Columnsfbrm100DMITxBiasCurrent | read-only | mandatory | Transmit bias current on local fiber interface, in microamperes. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.16 | Columnsfbrm100DMITxBiasAlarm | read-only | mandatory | . |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.17 | Columnsfbrm100DMITxPowerLevel | read-only | mandatory | DMI: Diagnostic Monitoring Interface for fiber transceivers. Transmit power on local fiber measured in microwatts. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.18 | Columnsfbrm100DMITxPowerAlarm | read-only | mandatory | . |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.19 | Columnsfbrm100DMIRxPowerLevel | read-only | mandatory | DMI: Diagnostic Monitoring Interface for fiber transceivers. Receive power on local fiber measured in microwatts. |
| 1.3.6.1.4.1.868.2.3.1.3.3.1.20 | Columnsfbrm100DMIRxPowerAlarm | read-only | mandatory | . |
| 1.3.6.1.4.1.868.2.3.1.3.4 | Tablesfbrm100PortL2CPTable | not-accessible | mandatory | Port L2CP processing. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1 | Rowsfbrm100PortL2CPEntry | not-accessible | mandatory | Status and configuration entries for a each port on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.1 | Columnsfbrm100PortL2CPLocIndex | read-only | mandatory | Uniquely indentifies each port on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.2 | Columnsfbrm100PortL2CPRmtIndex | read-only | mandatory | Uniquely indentifies each port on the peer device. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.3 | Columnsfbrm100STPProtocolsFwd | read-write | mandatory | Any STP/RSTP/MSTP protocol frames with destination address of 01-80-C2-00-00-00 is discarded at this port or tunnelled. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.4 | Columnsfbrm100SlowProtocolsFwd | read-write | mandatory | Any LACP/LAMP protocol frames with destination address of 01-80-C2-00-00-02 is discarded at this port or tunnelled. Since this device pairs link OAM frames, th… |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.5 | Columnsfbrm100PortAuthProtocolFwd | read-write | mandatory | Port authentication protocol frames with destination address of 01-80-C2-00-00-03 is discarded at this port or tunnelled. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.6 | Columnsfbrm100ELMIProtocolFwd | read-write | mandatory | E-LMI protocol frames with destination address of 01-80-C2-00-00-07 is discarded at this port or tunnelled. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.7 | Columnsfbrm100LLDPProtocolFwd | read-write | mandatory | LLDP protocol frames with destination address of 01-80-C2-00-00-0E is discarded at this port or tunnelled. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.8 | Columnsfbrm100BridgeMgmtProtocolsFwd | read-write | mandatory | Bridge Management protocol frames with destination address of 01-80-C2-00-00-10 is discarded at this port or tunnelled. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.9 | Columnsfbrm100GARPBlockProtocolsFwd | read-write | mandatory | GARP/MRP with destination address of 01-80-C2-00-00-20 to 01-80-C2-00-00-2F is discarded at this port or tunnelled. |
| 1.3.6.1.4.1.868.2.3.1.3.4.1.10 | Columnsfbrm100BridgeBlkOtherMulticastsFwd | read-write | mandatory | This mib variable tunnels or discards all the IEEE multicast frames in the bridge block of addresses [01-80-C2-00-00-20 to 01-80-C2-00-00-0F]. The mib variable… |
| 1.3.6.1.4.1.868.2.3.1.4 | NodesfbrmAddrDB | |||
| 1.3.6.1.4.1.868.2.3.1.4.1 | Tablesfbrm100FwdDBTable | not-accessible | mandatory | Learned address database for this device. |
| 1.3.6.1.4.1.868.2.3.1.4.1.1 | Rowsfbrm100FwdDBEntry | not-accessible | mandatory | Status and configuration entries for a single port on this device. |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.1 | Columnsfbrm100FwdLocPortIndex | read-only | mandatory | The entry can belong to the local switch or one of the remote peers. The local switch has the index as zero. The remote peers have the port index of the local … |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.2 | Columnsfbrm100FwdDBNum | read-only | mandatory | The Address Database Number the entry belongs to. DBNum of 0 is the default database. |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.3 | Columnsfbrm100FwdMacAddress | read-only | mandatory | The unicast or multicast address. |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.4 | Columnsfbrm100FwdConnPort | read-write | mandatory | The index of the logical Port from sfbrm100PortTable to which the MAC address is connected. |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.5 | Columnsfbrm100FwdPriority | read-write | mandatory | The priority of this entry. |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.6 | Columnsfbrm100FwdEntryType | read-write | mandatory | The Entry state of this unicast or multicast entry. The types represent : static(1) - A Valid entry that doesnot age. staticNRL(2) - A static entry that has no… |
| 1.3.6.1.4.1.868.2.3.1.4.1.1.7 | Columnsfbrm100FwdEntryStatus | read-write | mandatory | The status of the row and operations on the entry. write(1) is used to create a entry with default values. Immediately after completing the add operation, the … |
| 1.3.6.1.4.1.868.2.3.1.4.2 | Tablesfbrm100VlanTable | not-accessible | mandatory | VLAN database for this device. |
| 1.3.6.1.4.1.868.2.3.1.4.2.1 | Rowsfbrm100VlanEntry | not-accessible | mandatory | Status and configuration entries for a single port on this device. |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.1 | Columnsfbrm100VlanLocPortIndex | read-only | mandatory | The entry can belong to the local switch or one of the remote peers. The local switch has the index as zero. The remote peers have the port index of the local … |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.2 | Columnsfbrm100VlanDBNum | read-only | mandatory | The Address Database Number the entry belongs to. DBNum of 0 is the default database. |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.3 | Columnsfbrm100VlanVID | read-only | mandatory | The VLAN ID of the entry. |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.4 | Columnsfbrm100VlanVIDPriOverride | read-write | mandatory | Override Priority on frames assosicated with this VID. |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.5 | Columnsfbrm100VlanVIDPriority | read-write | mandatory | Priority for frames assosicated with this VID. |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.6 | Columnsfbrm100VlanMemTagPort1 | read-write | mandatory | Membership and Egress Tagging on Logical Port 1. memEgressNoMode(1)- Port 1 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.7 | Columnsfbrm100VlanMemTagPort2 | read-write | mandatory | Membership and Egress Tagging on Logical Port 2. memEgressNoMode(1)- Port 2 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.8 | Columnsfbrm100VlanMemTagPort3 | read-write | mandatory | Membership and Egress Tagging on Logical Port 3. memEgressNoMode(1)- Port 3 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.9 | Columnsfbrm100VlanMemTagPort4 | read-write | mandatory | Membership and Egress Tagging on Logical Port 4. memEgressNoMode(1)- Port 4 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.10 | Columnsfbrm100VlanMemTagPort5 | read-write | mandatory | Membership and Egress Tagging on Logical Port 5. memEgressNoMode(1)- Port 5 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.11 | Columnsfbrm100VlanMemTagPort6 | read-write | mandatory | Membership and Egress Tagging on Logical Port 6. memEgressNoMode(1)- Port 6 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.12 | Columnsfbrm100VlanMemTagPort7 | read-write | mandatory | Membership and Egress Tagging on Logical Port 7. memEgressNoMode(1)- Port 7 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.13 | Columnsfbrm100VlanMemTagPort8 | read-write | mandatory | Membership and Egress Tagging on Logical Port 8. memEgressNoMode(1)- Port 8 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.14 | Columnsfbrm100VlanMemTagPort9 | read-write | mandatory | Membership and Egress Tagging on Logical Port 9. memEgressNoMode(1)- Port 9 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) -… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.15 | Columnsfbrm100VlanMemTagPort10 | read-write | mandatory | Membership and Egress Tagging on Logical Port 10. memEgressNoMode(1)- Port 10 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2)… |
| 1.3.6.1.4.1.868.2.3.1.4.2.1.16 | Columnsfbrm100VlanEntryStatus | read-write | mandatory | The status of the row and operations on the entry. write(1) is used to create a entry with default values. Immediately after completing the add operation, the … |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CpsConnector | INTEGER { rj-45(10), stmm(11), stsm(12), scmm(13), scsm(14), scsmlh(15), scsmelh(16), scsmlhlw(17), mtrjmm(18), lc(19), bnc(20), stsmlh(21), stsmelh(22), scmm1300(23), stmm1300(24), mtrjsm(25), serial26(26), stmmlh(27), scsmsh(28), scsimplex(29), bncdual(30), db9rsxxx(31), termblock(32), rj11(33), sc40km(34), sc125km(35), din6(38) } | ||
| MacAddress | OCTET STRING (SIZE (6)) |